Gibson GCG91426XA User Manual

Add to my manuals
32 Pages

advertisement

Gibson GCG91426XA User Manual | Manualzz
GCG91326XA
GCG91426XA
Cooker
User Manual
Contents
Safety information
Safety instructions
Product description
Before first use
Hob - Daily use
Hob - Hints and tips
Hob - Care and cleaning
2
4
7
9
9
10
11
Oven - Daily use
Oven - Clock functions
Oven - Using the accessories
Oven - Hints and tips
Oven - Care and cleaning
Troubleshooting
Installation
12
13
13
15
18
20
21
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
for any injuries or damages that are the result of incorrect
installation or usage. Always keep the instructions in a safe
and accessible location for future reference.
Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability.
•
•
•
•
•
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts are hot.
Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
General Safety
•
2
Only a qualified person must install this appliance and
replace the cable.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
This appliance is intended for use up to an altitude of 2000
m above sea level.
This appliance is not intended to be used on a ships, boats
or vessels.
Do not install the appliance behind a decorative door in order
to avoid overheating.
Do not install the appliance on a platform.
Do not operate the appliance by means of an external timer
or separate remote-control system.
WARNING: Unattended cooking on a hob with fat or oil can
be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire
blanket.
CAUTION: The cooking process has to be supervised. A
short term cooking process has to be supervised
continuously.
WARNING: Danger of fire: Do not store items on the cooking
surfaces.
Do not use a steam cleaner to clean the appliance.
Do not use harsh abrasive cleaners or sharp metal scrapers
to clean the glass door or the glass of hinged lids of the hob
since they can scratch the surface, which may result in
shattering of the glass.
Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they can get
hot.
Remove any spillage from the lid before opening. Let the
hob surface cool down before closing the lid.
WARNING: The appliance and its accessible parts become
hot during use. Care should be taken to avoid touching
heating elements. Children less than 8 years of age shall be
kept away unless continuously supervised.
Always use oven gloves to remove or put in accessories or
ovenware.
Before maintenance cut the power supply.
3
•
•
•
Ensure that the appliance is switched off before replacing
the lamp to avoid the possibility of electric shock.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre
or similarly qualified persons to avoid an electrical hazard.
WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by the
manufacturer of the appliance in the instructions for use as
suitable or hob guards incorporated in the appliance. The
use of inappropriate guards can cause accidents.
Safety instructions
This appliance is suitable for the following
markets: IQ KW QA AE
Installation
WARNING!
Only a qualified person must install
this appliance.
•
•
•
•
•
•
•
•
•
•
•
Remove all the packaging.
Do not install or use a damaged appliance.
Follow the installation instruction supplied
with the appliance.
Always take care when moving the
appliance as it is heavy. Always use safety
gloves and enclosed footwear.
Do not pull the appliance by the handle.
The kitchen cabinet and the recess must
have suitable dimensions.
Keep the minimum distance from the other
appliances and units.
Make sure that the appliance is installed
below and adjacent safe structures.
Parts of the appliance carry current. Close
the appliance with furniture to prevent
touching the dangerous parts.
The sides of the appliance must stay
adjacent to appliances or to units with the
same height.
Do not install the appliance adjacent to a
door or under a window. This prevents hot
cookware to fall from the appliance when
the door or the window is opened.
Electrical Connection
WARNING!
Risk of fire and electrical shock.
•
•
•
•
•
•
•
•
•
•
•
•
4
All electrical connections should be made
by a qualified electrician.
The appliance must be earthed.
Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
Always use a correctly installed shockproof
socket.
Do not use multi-plug adapters and
extension cables.
Do not let mains cables touch or come
near the appliance door, especially when
the door is hot.
The shock protection of live and insulated
parts must be fastened in such a way that
it cannot be removed without tools.
Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
If the mains socket is loose, do not
connect the mains plug.
Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
The electrical installation must have an
isolation device which lets you disconnect
the appliance from the mains at all poles.
•
The isolation device must have a contact
opening width of minimum 3 mm.
Fully close the appliance door, before you
connect the mains plug to the mains
socket.
Gas connection
•
•
•
•
•
All gas connections should be made by a
qualified person.
Before installation, make sure that the
local distribution conditions (nature of the
gas and gas pressure) and the adjustment
of the appliance are compatible.
Make sure that there is air circulation
around the appliance.
The information about the gas supply is on
the rating plate.
This appliance is not connected to a
device, which evacuates the products of
combustion. Make sure to connect the
appliance according to current installation
regulations. Pay attention to requirements
regarding adequate ventilation.
•
•
•
•
WARNING!
Risk of damage to the appliance.
•
Use
WARNING!
Risk of injury and burns.
Risk of electrical shock.
•
•
•
•
•
•
•
•
This appliance is for household use only.
Do not change the specification of this
appliance.
Make sure that the ventilation openings
are not blocked.
Do not let the appliance stay unattended
during operation.
Deactivate the appliance after each use.
Be careful when you open the appliance
door while the appliance is in operation.
Hot air can release.
Do not operate the appliance with wet
hands or when it has contact with water.
Do not use the appliance as a work
surface or as a storage surface.
WARNING!
Risk of fire and explosion
•
•
Fats and oil when heated can release
flammable vapours. Keep flames or heated
objects away from fats and oils when you
cook with them.
The vapours that very hot oil releases can
cause spontaneous combustion.
Used oil, that can contain food remnants,
can cause fire at a lower temperature than
oil used for the first time.
Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
Do not let sparks or open flames to come
in contact with the appliance when you
open the door.
Open the appliance door carefully. The
use of ingredients with alcohol can cause a
mixture of alcohol and air.
•
•
•
•
•
•
•
•
•
•
•
To prevent damage or discoloration to the
enamel:
– do not put ovenware or other objects in
the appliance directly on the bottom.
– do not put water directly into the hot
appliance.
– do not keep moist dishes and food in
the appliance after you finish the
cooking.
– be careful when you remove or install
the accessories.
Discoloration of the enamel or stainless
steel has no effect on the performance of
the appliance.
Use a deep pan for moist cakes. Fruit
juices cause stains that can be permanent.
Do not keep hot cookware on the control
panel.
Do not let cookware boil dry.
Be careful not to let objects or cookware
fall on the appliance. The surface can be
damaged.
Do not activate the cooking zones with
empty cookware or without cookware.
Do not put aluminium foil on the appliance
or directly on the bottom of the appliance.
Cookware made of cast iron, aluminium or
with a damaged bottom can cause
scratches. Always lift these objects up
when you have to move them on the
cooking surface.
Provide good ventilation in the room where
the appliance is installed.
Use only stable cookware with the correct
shape and diameter larger than the
dimensions of the burners.
Make sure the flame does not go out when
you quickly turn the knob from the
maximum to the minimum position.
5
•
•
•
Use only the accessories supplied with the
appliance.
Do not install a flame diffuser on the
burner.
This appliance is for cooking purposes
only. It must not be used for other
purposes, for example room heating.
•
Care and Cleaning
WARNING!
Risk of injury, fire, or damage to
the appliance.
•
•
•
•
•
•
•
•
•
•
Before maintenance, deactivate the
appliance.
Disconnect the mains plug from the mains
socket.
Make sure the appliance is cold. There is
the risk that the glass panels can break.
Replace immediately the door glass panels
when they are damaged. Contact the
Authorised Service Centre.
Be careful when you remove the door from
the appliance. The door is heavy!
Fat and food remaining in the appliance
can cause fire.
Clean regularly the appliance to prevent
the deterioration of the surface material.
Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
any abrasive products, abrasive cleaning
pads, solvents or metal objects.
If you use an oven spray, obey the safety
instructions on the packaging.
Do not clean the catalytic enamel (if
applicable) with any kind of detergent.
Do not clean the burners in the
dishwasher.
Internal light
•
Risk of electrical shock.
•
•
WARNING!
Risk of fire, explosion and burns.
•
•
•
Do not leave the appliance unattended
during grilling. Accessible parts become
hot.
Keep children away when the grill is in
use.
Do not put the oven shelf with food on the
highest shelf level.
Disposal
WARNING!
Risk of injury or suffocation.
•
•
•
•
•
Before replacing the lamp, disconnect the
appliance from the power supply.
Only use lamps with the same
specifications.
Gas Grill
•
•
•
The type of light bulb or halogen lamp
used for this appliance is only for
household appliances. Do not use it for
house lighting.
WARNING!
Lid
Do not change the specification of the lid.
Clean the lid regularly.
Do not open the lid, when there are spills
on the surface.
Before you close the lid turn all burners off.
Do not close the lid until the hob and oven
are completely cold.
Glass lid can shatter, when heated (if
applicable).
Keep the lid glass open, while the oven is
in operation (if applicable).
•
•
•
Contact your municipal authority for
information on how to discard the
appliance correctly.
Disconnect the appliance from the mains
supply.
Cut off the mains electrical cable close to
the appliance and dispose of it.
Remove the door catch to prevent children
or pets from becoming trapped in the
appliance.
Flat the external gas pipes.
Service
•
6
To repair the appliance contact an
Authorised Service Centre.
•
Use original spare parts only.
Product description
Cooker specification
Initial gas settings
GCG91426XA
943006405
Model denomination and PNC number
GCG91326XA
943006306
Check the table to see your appliance's
detailed specification.
X
X
Natural gas
LPG
Additional gas injectors
X
Hob integrated ignition on the control
knob
Hob ignition on the spark generator but‐
ton
X
X
Oven ignition on the spark generator but‐
ton
X
X
Hob thermocouple
X
X
Oven thermocouple
X
X
X
X
Oven integrated ignition on the control
knob
Oven cleaning
Pan support
Enamel
Catalytic
Enamel
Cast iron
X
X
7
General overview
1 2 3
4
5
6
7
12
8
9
5
4
3
2
1
10
11
1
2
3
4
5
6
7
8
9
10
11
12
Button for the turnspit
Button for the spark generator
Knob for the Minute Minder
Knob for the grill
Knob for the oven functions
Button for the lamp
Knobs for the hob
Grill
Lamp
Turnspit hole
Fan
Shelf positions
Cooking surface layout
1
2
3
6
5
4
1 Auxiliary burner
2 Steam outlet - number and position
depend on the model
3 Semi-rapid burner
4 Semi-rapid burner
5 Triple Crown burner
6 Rapid burner
Accessories
•
•
•
•
8
Wire shelf
For cookware, cake tins, roasts.
Baking tray
For cakes and biscuits.
Turnspit
For roasting larger joints of meat and
poultry.
Storage compartment
The storage compartment is below the
oven cavity. To use the compartment, lift
the lower front door then pull it down.
WARNING!
•
The storage compartment can
become hot when the appliance
operates.
Coffee pot (if applicable)
For coffee makers and small pans.
Before first use
WARNING!
Refer to Safety chapters.
Initial Cleaning
Remove all accessories from the appliance.
Refer to "Care and cleaning"
chapter.
Clean the appliance and the accessories
before first use.
Put the accessories back to their initial
position.
1. Set the maximum temperature.
2. Let the appliance operate for
approximately 1 hour.
WARNING!
Accessories can become hotter
than usual.
The appliance can emit an odour and smoke.
This is normal. Make sure that the airflow is
sufficient.
Let the oven cool down. Dampen a soft cloth
with warm water and a little mild washing-up
liquid and use this to clean the oven cavity.
Preheating
Preheat the empty appliance to burn off the
remaining grease.
Hob - Daily use
WARNING!
Refer to Safety chapters.
Ignition of the hob burner
Always light the burner before you
put on the cookware.
WARNING!
Be very careful when you use open
fire in the kitchen environment. The
manufacturer declines any
responsibility in case of the flame
misuse.
The spark generator can start
automatically when you switch on
the mains, after installation or a
power cut. It is normal.
In the absence of electricity you
can ignite the burner manually.
Ignition of a hob burner with the
thermocouple
•
•
For manual ignition put the flame near the
burner. Push the knob for the hob down
and turn it counterclockwise to the
. At the same time push the knob for the
hob down and turn it counterclockwise to
the maximum gas flow position .
Release the spark generator button when
burner lights.
Keep the knob for the hob pushed for equal or
less than 10 seconds to let the thermocouple
warm up. If not, the gas supply is interrupted.
Adjust the flame after it is regular.
WARNING!
Do not keep the knob pushed for
more than 15 seconds. If the
burner does not light after 15
seconds, release the knob, turn it
into the off position and try to light
the burner again after minimum 1
minute.
If after some tries the burner does
not light, check if the crown and its
cap are in the correct position.
If the burner accidentally goes out,
turn the knob to the off position
and try to light the burner again
after minimum 1 minute.
maximum gas flow position .
For ignition with spark generator button
push and hold the spark generator button
9
Burner overview
A.
B.
C.
D.
Burner cap
Burner crown
Ignition candle
Thermocouple (if applicable)
Turning the burner off
A
To put the flame out, turn the knob to the off
position
.
WARNING!
B
Always turn the flame down or
switch it off before you remove the
pans from the burner.
C
D
A
B
C
D
Hob - Hints and tips
WARNING!
Refer to Safety chapters.
Cookware
WARNING!
Do not put the same pan on two
burners.
10
WARNING!
Do not put unstable or damaged
pots on the burner to prevent from
spill and injury.
CAUTION!
Make sure that pot handles are not
above the front edge of the
cooktop.
CAUTION!
Make sure that the pots are placed
centrally on the burner in order to
get maximum stability and to get
lower gas consumption.
Diameters of cookware
WARNING!
Use cookware with diameters
applicable to the size of burners.
Burner
Rapid
160 - 240
Semi-rapid
140 - 240
Auxiliary
120 - 180
Energy saving
•
Burner
Diameter of cook‐
ware (mm)
Triple Crown
Diameter of cook‐
ware (mm)
•
If it is possible, always put the lids on the
cookware.
When the liquid starts to boil, turn down
the flame to barely simmer the liquid.
160 - 260
Hob - Care and cleaning
WARNING!
Refer to Safety chapters.
General information
•
•
•
•
•
Clean the hob after each use.
Always use cookware with clean bottom.
Scratches or dark stains on the surface
have no effect on how the hob operates.
Use a special cleaner applicable for the
surface of the hob.
Wash stainless steel parts with water, and
then dry them with a soft cloth.
Cleaning the hob
•
•
•
Remove immediately: melted plastic,
plastic foil, sugar and food with sugar. If
not, the dirt can cause damage to the hob.
Take care to avoid burns.
Remove when the hob is sufficiently
cool: limescale rings, water rings, fat
stains, shiny metallic discoloration. Clean
the hob with a moist cloth and nonabrasive detergent. After cleaning, wipe
the hob dry with a soft cloth.
To clean the enamelled parts, cap and
crown, wash them with warm soapy water
and dry them carefully before you put them
back on.
Cleaning the spark plug
This feature is obtained through a ceramic
ignition candle with a metal electrode. Keep
these components well clean to prevent
difficult lighting and check that the burner
crown holes are not obstructed.
Pan supports
The pan supports are not resistant
to washing in a dishwasher. They
must be washed by hand.
1. Remove the pan supports to easily clean
the hob.
Be very careful when you
replace the pan supports to
prevent the hob top from
damage.
2. The enamel coating occasionally can
have rough edges, so be careful when
you wash the pan supports by hand and
dry them. If necessary, remove stubborn
stains with a paste cleaner.
3. After you clean the pan supports, make
sure that they are in correct positions.
4. For the burner to operate correctly, make
sure that the arms of the pan supports are
aligned with the centre of the burner.
Periodic maintenance
Speak to your local Authorised Service
Centre periodically to check the conditions of
the gas supply pipe and the pressure
adjuster, if fitted.
11
Oven - Daily use
WARNING!
Refer to Safety chapters.
Oven Functions
Oven function
MIN 240°C
MIN 240°C
Application
Off position
The appliance is off.
Heat settings
Range of temperature adjustment.
Grilling
To grill flat food in the middle of the grill. To make
toast.
Oven fan
To thaw frozen food.
Oven lamp
To illuminate the oven interior.
To use this function, press the button for the lamp.
Turnspit
To spit roasting meat.
Gas Multifunction
To cook several different dishes at the same time. To
cook home-made syrup, dry mushrooms or fruit.
Ignition of the oven gas burner
CAUTION!
When turning on the oven burner
the oven door must be opened.
CAUTION!
Make sure that the lid is opened.
When using the oven the lid has to
be opened to avoid over-heating.
Oven safety device:
The gas oven has a thermocouple.
It stops the gas flow if the flame
goes out.
1. Open the oven door.
2. Ignite the oven gas burner.
• For ignition on the spark generator
button push and hold the button . At
the same time turn the knob for the
oven functions counterclockwise to the
12
maximum heat settings and push it to
light the burner. Release the spark
generator button when burner lights.
Keep the knob for the oven functions
pushed for 15 seconds or less to let the
thermocouple warm up. If not, the gas
flow is interrupted.
Manual ignition of oven gas burner
In case of absence of the electricity you can
ignite the oven burner without an electrical
device.
1. Open the oven door.
2. Hold the flame near the hole in the bottom
of the oven cavity.
Using the grill
CAUTION!
Always keep the appliance door
closed when the grill operates.
Do not put the meat directly on the
tray or pan.
3. At the same time push the knob for the
oven functions and turn it
counterclockwise to the maximum gas
flow position.
4. When the flame comes on, keep the knob
for the oven functions pushed on the
maximum gas flow position for 15
seconds or less to let the thermocouple
warm up.
Do not keep the knob for the oven
functions pushed for more than 15
seconds. If the oven burner does
not light after 15 seconds, release
the knob for the oven functions,
turn it into off position, open the
oven door and try to light the oven
burner again after minimum 1
minute.
After igniting the oven gas burner
1. Release the knob for the oven functions.
2. Close the oven door.
3. Turn the knob for the oven functions to set
the necessary heat setting.
Control the flame trough the holes in the
bottom of the oven.
CAUTION!
Do not put the meat on the highest
shelf level. There is a risk of fire.
1. Open the oven door.
2. Ignite the grill burner.
• For manual ignition hold a flame near
the grill burner holes. Push and turn
the knob for the grill to the flame
position. Hold the knob pushed down.
3. Hold the knob for the grill pushed for
approximately 15 seconds.
4. Release the oven control knob.
The grill temperature can be adjusted. To
lower the temperature turn the knob for
the grill counterclockwise.
If the grill does not come on or if it
accidentally goes out release the knob for
the oven functions and turn it to the Off
position. Open the oven door. After one
minute, try to light the grill again.
5. Preheat the grill for 5 to 10 minutes.
6. Put the oven shelf with the meat on shelf
position 3.
7. Put a baking tray or roasting pan below,
on shelf position 2, to collect the juices.
Turning off the grill burner
Turning off the oven burner
To put out the flame, turn the knob to the off
To put out the flame, turn the knob to the off
position
position
.
.
Oven - Clock functions
Minute Minder
This function has no effect on the
operation of the appliance.
Turn the knob for the timer as far as it goes,
then turn it to necessary time period.
After the time period is completed, an
acoustic signal sounds.
Oven - Using the accessories
WARNING!
Refer to Safety chapters.
Inserting the accessories
Wire shelf:
13
CAUTION!
The maximum weight permitted on
the turnspit is 4.5 kg.
A
B
Put the shelf on the correct shelf position.
Make sure it does not touch the back wall of
the oven.
WARNING!
The maximum weight permitted on
the oven shelf is 24 kg. Avoid
putting heavier food on the shelf.
Tray:
Do not push the baking tray all the
way to the back wall of the cavity.
This prevents the heat from
circulating around the tray. The
food may be burnt, especially in
the rear part of the tray.
C
D
A.
B.
C.
D.
Support hook
Forks
Spit
Handle
The support hook is installed in the
top of the oven cavity.
You can leave the support hook in
the oven, when the turnspit is not
active.
1. Open the oven door.
2. Put the turnspit handle into the spit.
3. Put the baking tray on the lowest shelf
level.
4. Snap out one end of the support hook
from the oven ceiling A and let it hang on
the other end.
A
Put the tray or deep pan on the shelf position.
Make sure it does not touch the back wall of
the oven.
Using the turnspit
WARNING!
Be careful when you use the
turnspit. The forks and the spit are
sharp. There is a risk of injury.
WARNING!
Use oven gloves when you remove
the turnspit. The turnspit and the
grill are hot. There is a risk of
burns.
14
5. Install the first fork on the spit, then put
the meat on the turnspit and install the
second fork.
Make sure that the meat is in the middle
of the spit.
6. Use the screws to tighten the forks.
7. Put the tip of the spit into the turnspit hole.
Refer to "Product description" chapter.
8. Put the front part of the spit on the support
hook.
9. Remove the turnspit handle.
10. Light the grill.
Refer to "Oven - Daily use" chapter.
11. Press the turnspit button .
12. Make sure that turnspit rotates.
13. Close the oven door.
The turnspit does not stop if you open the
oven door.
When meat is ready press the turnspit button.
Turn off the grill. Install the turnspit handle.
Carefully remove the turnspit and the roasting
pan from the oven.
Oven - Hints and tips
This can change the baking results and
cause damage to the enamel.
WARNING!
Refer to Safety chapters.
The temperature and baking times
in the tables are guidelines only.
They depend on the recipes and
the quality and quantity of the
ingredients used.
General information
•
•
•
•
•
The appliance has five shelf positions.
Count the shelf positions from the bottom
of the appliance floor.
The appliance has a special system which
circulates the air and constantly recycles
the steam. With this system you can cook
in a steamy environment and keep the
food soft inside and crusty outside. It
decreases the cooking time and energy
consumption to a minimum.
Moisture can condense in the appliance or
on the door glass panels. This is normal.
Always stand back from the appliance
when you open the appliance door while
cooking. To decrease the condensation,
operate the appliance for 10 minutes
before cooking.
Clean the moisture after each use of the
appliance.
Do not put the objects directly on the
appliance floor and do not put aluminium
foil on the components when you cook.
Baking
•
•
•
•
•
Your oven may bake or roast differently to
the appliance you had before. Adapt your
usual settings such as temperature,
cooking time and shelf position to the
values in the tables.
Use the lower temperature the first time.
If you cannot find the settings for a special
recipe, look for the similar one.
Cakes and pastries at different heights do
not always brown equally at first. If this
occurs, do not change the temperature
setting. The differences equalize during
the baking procedure.
Trays in the oven can twist during baking.
When the trays become cold again, the
distortions disappear.
Baking cakes
•
Do not open the oven door before 3/4 of
the set cooking time is up.
Cooking meat and fish
•
•
Use a deep pan for very fatty food to
prevent the oven from stains that can be
permanent.
Leave the meat for approximately 15
minutes before carving so that the juice
does not seep out.
15
•
Initially, monitor the performance when you
cook. Find the best settings (heat setting,
cooking time, etc.) for your cookware, recipes
and quantities when you use this appliance.
To prevent too much smoke in the oven
during roasting, add some water into the
deep pan. To prevent the smoke
condensation, add water each time after it
dries up.
Cooking times
Cooking times depend on the type of food, its
consistency, and volume.
Cooking tables
Casseroles
Food
Quantity (kg)
Temperature
(°C)
Time (min)
Shelf position
Lasagna1)
2.5 - 4.0
180
45 - 50
2
Cannelloni
2.5 - 4.0
180
50 - 60
2
2.5 - 3.0
170
60 - 65
2
4.0 - 4.5
190
45 - 50
2
3.5 - 4.0
195
40 - 45
2
1)
Potato gratin
1)
Macaroni oven
1)
Kebab Hala
1) Preheat the oven for 15 minutes.
Meat & Poultry
Food
Quantity (kg)
Temperature
(°C)
Time (min)
Shelf position
Sheep
3.0 - 4.0
210
90 - 120
2
Chicken
2.0 - 3.5
240
100 - 1101)
2
Duck
2.4 - 3.6
240
80 - 90
2
Goose
5.0 - 6.0
240
80 - 90
2
Rabbit
2.0 - 3.0
195
90 - 120
2
Beef
2.4 - 3.0
210
90 - 120
2
1) Turn over after 50 min.
Fish
Food
Pike
16
Quantity (kg)
1.6 - 3.0
Temperature
(°C)
180
Time (min)
50 - 60
Shelf position
2
Food
Quantity (kg)
Temperature
(°C)
Time (min)
Shelf position
Dorade
0.8 - 1.4
180
30 - 40
2
Trout
1.0 - 2.0
180
25 - 30
2
Pizza
Food
Thin
Quantity (kg)
Temperature
(°C)
Time (min)
Shelf position
1.5 - 2.5
240
20 - 30
1
1.5 - 2.0
240
25 - 30
1
1.5 - 2.5
210
30 - 35
1
1)
Thick
1)
Calzone
1)
1) Preheat the oven for 15 minutes.
Cakes
Food
Flat cake
Quantity (kg)
Temperature
(°C)
Time (min)
Shelf position
1.2 - 1.5
170
20 - 25
2
2.4 - 3.0
170
25 - 30
2 and 4
Sponge cake
3.0 - 3.5
170
85 - 90
2
Feter Mshalted
2.5 - 3.0
195
40 - 45
2
3.0 - 3.5
195
50 - 60
2
2.5 - 3.0
195
45 - 50
2
1)
Flat cake
1)
1)
Salty cake
1)
Yeast cake
1)
1) Preheat the oven for 15 minutes.
Grilling
Food
Sheep chops1)
Quantity (kg)
1.5 - 2.5
Grill position
half
Time (min)
20 - 25
Shelf position
3
17
Food
Ribs
Quantity (kg)
Grill position
Time (min)
Shelf position
2.0 - 2.5
half
45 - 60
3
3.0 - 3.5
max.
15 - 20
3
2.5 - 3.0
half
20 - 25
3
1.0 - 1.2
max.
7 - 10
3
1.0 - 2.0
max.
15 - 20
3
1)
Burgers
1)
Mackerel
1)
Toast browning
1)
Toast Hawai
1)
1) Preheat the oven for 10 minutes.
Revolving frying
Food
Quantity (kg)
Grill position
Time (min)
Shelf position
Sheep on skewer 3.0 - 4.0
max.
100 - 120
Turnspit
Chicken on
skewer
max.
120 - 130
Turnspit
3.0 - 3.5
Oven - Care and cleaning
WARNING!
Refer to Safety chapters.
Notes on cleaning
•
•
•
•
•
•
18
Clean the front of the appliance with a soft
cloth with warm water and a cleaning
agent.
To clean metal surfaces, use a dedicated
cleaning agent.
Clean the appliance interior after each use.
Fat accumulation or other food remains
may result in a fire.
Clean stubborn dirt with a special oven
cleaner.
Clean all accessories after each use and
let them dry. Use a soft cloth with warm
water and a cleaning agent.
If you have nonstick accessories, do not
clean them using aggressive agents,
sharp-edged objects or a dishwasher. It
can cause damage to the nonstick coating.
Stainless steel or aluminium appliances
Clean the oven door with a damp
cloth or sponge only. Dry it with a
soft cloth.
Do not use steel wool, acids or
abrasive materials as they can
damage the oven surface. Clean
the oven control panel with the
same precautions.
Cleaning the oven door
The oven door has two panels of glass
installed one behind the other. To make the
cleaning easier remove the oven door.
WARNING!
The oven door can close if you try
to remove the internal panel of
glass when the door is still
assembled.
against the top edge of the door. Lift the
inner door.
Do not lose the screws.
1. Open the door fully and hold the two door
hinges.
2. Lift and turn the levers on the two hinges.
3
2 2
7. Clean the oven door with water and soap.
Clean inner side of the door. Dry the oven
door carefully.
When the cleaning is completed, install the
glass panels and the oven door. To install the
oven door, do the above steps in the opposite
sequence.
4
4
6
5
3. Close the oven door to the first opening
position (halfway). Then pull forward and
remove the door from its seat.
5
Replacing the lamp
Put a cloth on the bottom of the interior of the
appliance. It prevents damage to the lamp
glass cover and the cavity.
WARNING!
4. Put the door on a soft cloth on a stable
surface.
5. Use a screwdriver to remove 2 screws
from bottom edge of door.
Danger of electrocution!
Disconnect the fuse before you
replace the lamp.
The lamp and the lamp glass cover
can be hot.
1. Deactivate the appliance.
2. Remove the fuses from the fuse box or
deactivate the circuit breaker.
1
1
6. Use a spatula made of wood or plastic or
equivalent to open the inner door. Hold
the outer door, and push the inner door
The back lamp
1. Turn the lamp glass cover
counterclockwise to remove it.
2. Clean the glass cover.
3. Replace the lamp with a suitable 300 °C
heat-resistant lamp.
4. Install the glass cover.
19
Troubleshooting
WARNING!
Refer to Safety chapters.
What to do if...
Problem
Possible cause
Remedy
There is no spark when you try
to activate the spark generator.
The hob is not connected to an
electrical supply or it is connec‐
ted incorrectly.
Check if the hob is correctly
connected to the electrical sup‐
ply. Refer to the connection dia‐
gram.
There is no spark when you try
to activate the spark generator.
The fuse is blown.
Make sure that the fuse is the
cause of the malfunction. If the
fuse is blown again and again,
contact a qualified electrician.
There is no spark when you try
to activate the spark generator.
Burner cap and crown are
placed incorrectly.
Place the burner cap and crown
correctly.
The flame extinguishes immedi‐
ately after ignition.
Thermocouple is not heated up
sufficiently.
After lightning the flame, keep
the spark generator activated
for equal or less than 10 sec‐
onds
The flame ring is uneven.
Burner crown is blocked with
food residues.
Make sure that the injector is
not blocked and the burner
crown is clean.
The burners do not work.
There is no gas supply.
Check the gas connection.
The appliance makes noises.
Some metal parts of the appli‐
ance expand and contract when
they heat up or cool down. The
noises are normal.
The flame colour is orange or
yellow.
The flame can look orange or
yellow in some areas of the
burner. This is normal.
The lamp does not operate.
The lamp is defective.
Replace the lamp.
Steam and condensation settle
on the food and in the cavity of
the oven.
You left the dish in the oven for
too long.
Do not leave the dishes in the
oven for longer than 15 - 20 mi‐
nutes after the cooking process
ends.
The oven does not heat up.
The necessary settings are not
set.
Make sure that the settings are
correct.
The turnspit does not rotate.
The turnspit is not correctly in‐
stalled into the turnspit hole.
Refer to "Using the turnspit".
20
Problem
Possible cause
It takes too long to cook the
dishes or they cook too quickly.
The temperature is too low or
too high.
Service data
If you cannot find a solution to the problem
yourself, contact your dealer or an Authorised
Service Centre.
Remedy
Adjust the temperature if neces‐
sary. Follow the advice in the
user manual.
front frame of the appliance cavity. Do not
remove the rating plate from the appliance
cavity.
The necessary data for the service centre is
on the rating plate. The rating plate is on the
We recommend that you write the data here:
Model (MOD.)
.........................................
Product number (PNC)
.........................................
Serial number (S.N.)
.........................................
Installation
WARNING!
Refer to Safety chapters.
Location of the appliance
You can install your freestanding appliance
with cabinets on one or two sides and in the
corner.
B
Keep a distance of about 1 cm
between the appliance and the
back wall to make sure that the lid
opens.
C
A
For minimal distances for fitting check the
table.
D
D
Minimum distances
Dimension
mm
A
400
B
650
C
150
21
Dimension
mm
D
Appliance class
20
Technical data
1
Dimension
mm
Height
850 - 870
Voltage
220 - 240 V
Width
900
Frequency
50 - 60 Hz
Depth
600
Other technical data
Appliance category:
II2H3B/P
LPG:
G30 (3B/P) 28-30 mbar
Natural Gas:
G20 (2H) 20 mbar
Bypass diameters
BURNER
Ø BYPASS 1/100 mm
Auxiliary
29 / 30
Semi-rapid
32
Rapid
42
Triple Crown
67
Oven
54
Grill
59
Gas burners for NATURAL GAS G20 20 mbar
BURNER
NORMAL POWER
kW
REDUCED POWER kW
INJECTOR MARK
1/100 mm
Triple Crown
4.0
1.8
146
Rapid
3.0
0.72
119
Semi-rapid
2.0
0.43
96
Auxiliary
1.0
0.35
70
Oven
3.6
1.5
126
Grill
2.5
1.6
111
22
Gas burners for LPG G30 28-30 mbar
BURNER
NORMAL
POWER kW
GAS RATE g/h
REDUCED POW‐
ER kW
INJECTOR MARK
1/100 mm
Triple Crown
4.0
290.8
1.8
101
Rapid
3.0
218.1
0.72
88
Semi-rapid
2.0
145.4
0.43
71
Auxiliary
1.0
72.7
0.35
50
Oven
3.6
261.8
1.5
90
Grill
2.5
181.8
1.6
80
Gas connection
The gas pipe in the appliance has two
endings. You can connect the gas supply to
either one of them. The pipe that is not used
must be clogged with the pipe closer, which
added to the appliance.
Use a fixed connections or use a flexible
stainless steel pipes in compliance with the
regulation in force. If you use flexible metallic
pipes, make sure they do not come in touch
with mobile parts and they are not squeezed.
In installation always use the pipe holder and
the gasket. The flexible pipe can be applied
when:
•
it can not get hotter than room
temperature, higher than 30 °C,
• it is not longer than 1500 mm,
• it has no narrowing anywhere,
• it is not twisted or tighten,
• it does not get in touch with sharp edges or
corners,
• it's conditions can be easily checked.
When checking the flexible pipe make sure:
•
it does not show cracks, cuts, marks of
burnings on the two ends and on its full
length,
• the material is not hardened, but shows its
correct elasticity,
• the fastening clamps are not rusted,
• expired term is not due.
If one or more defects are visible, do not
repair the pipe, but replace it.
WARNING!
When installation is complete,
make sure that the seal of each
pipe fitting does not leak. To check
the seal use a soap solution, not a
flame.
The gas supply ramp is on the rear side of the
control panel.
Flexible nonmetal pipes connection
If you have an easy access to the connection,
you can use a flexible pipe. The flexible pipe
must be tightly attached by clamps.
WARNING!
Before you connect the gas,
disconnect the appliance from the
electricity supply or switch off the
fuse in the fuse box. Close the
primary valve of the gas supply.
23
Adjustment to different types of gas
WARNING!
Let only an authorized person do
the adjustment to different types of
gas.
Check the table in chapter
"Product descriptions" to see the
initial gas of your appliance.
If the appliance is set for natural
gas you can change it to liquid gas,
with the correct injectors.
If the appliance is set for liquid gas
you can change it to natural gas,
with the correct injectors.
The gas rate is adjusted to suit.
WARNING!
Before you replace the injectors,
make sure that the gas knobs are
in the Off position. Disconnect the
appliance from the electrical
supply. Let the appliance cool
down. There is a risk of injury.
The appliance is set to default gas.
To change the setting choose a
pipe holder from the list. Always
use the gasket sealing.
A
B
C
A. Gas connection end
B. Natural Gas pipe holder
C. LPG pipe holder
Hob injectors replacement
Replace the injectors when you change the
gas type.
1. Remove the pan supports.
2. Remove the caps and crowns of the
burner.
3. Remove the injectors with a socket
spanner 7.
4. Replace injectors with the ones necessary
for the type of gas you use.
24
5. Replace the rating plate (it is near the gas
supply pipe) with the one for the new type
of gas supply.
You can find this plate in the
bag supplied with the
appliance.
If the supply gas pressure is not constant or it
is different from the necessary pressure,
install an applicable pressure adjuster on the
gas supply pipe.
Adjusting the minimum gas level on the
hob burner
1. Disconnect the appliance from the
electricity.
2. Remove the knob for the hob. If there is
no access to the bypass screw dismount
the control panel before adjustment start.
3. With a thin and flat screwdriver adjust the
bypass screw A.
The model determines the position of the
bypass screw A.
A
A
Changing from natural gas to liquid
gas
1. Fully tighten the bypass screw.
2. Put the knob back.
Changing from liquid gas to natural
gas
1. Unscrew approximately one turn the
bypass screw position A.
2. Put the knob for the hob back.
3. Connect the appliance to the electricity.
WARNING!
4.
5.
6.
7.
8.
Put the mains plug into the
mains socket only if all parts
are back into their initial
position. There is a risk of
injury.
Light the burner.
Refer to "Hob - Daily use" chapter.
Turn the knob for the hob to the minimum
position.
Remove the knob for the hob again.
Screw on slowly the bypass screw till the
flame becomes minimum and stable.
Put the knob for the hob back on.
A
B
Oven injector replacement
1. Remove the bottom plate of the oven
cavity to get access to the oven burner .
3. Unscrew the screw and slowly pull out the
burner.
1
2
2. Carefully remove from the burner the
thermocouple A. Next remove the spark
plug B.
4. Release the burner injector with a 7 mm
socket spanner and replace it with a right
one.
25
Changing from liquid gas to natural
gas
1. Unscrew approximately one turn the
bypass screw position A.
2. Put the knob for the oven functions back.
3. Connect the appliance to the electricity.
WARNING!
Assemble the burner in a revers sequence.
Replace the gas type sticker near the gas
supply ramp with the one related to the new
gas type.
Adjusting the minimum gas level on the
oven burner
1. Disconnect the appliance from the
electricity.
2. Remove the knob for the oven functions.
If there is no access to the bypass screw
dismount the control panel before
adjustment start.
3. With a thin and flat screwdriver adjust the
bypass screw A.
The model determines the position of the
bypass screw A.
A
Put the mains plug into the
mains socket only if all parts
are back into their initial
position. There is a risk of
injury.
4. Light the burner.
Refer to "Oven - Daily use" chapter.
5. Turn the knob for the oven functions on
the minimum position.
6. Remove the knob for the oven functions
again.
7. Screw on slowly the bypass screw till the
flame becomes minimum and stable.
8. Put the knob for the oven functions back.
9. Set the maximum gas flow position on the
knob for the oven functions and let the
oven heat for at least 10 minutes.
10. Quickly turn the knob for the oven
functions from maximum to the minimum
gas flow position.
Control the flame. Make sure the flame does
not go out when you turn the knob to the
minimum gas flow position. There must be a
small regular flame on the oven burner crown.
If the flame goes out adjust the oven burner
again.
Gas grill injector replacement
1. Release the screws which keep the grill
burner in position A.
A
Changing from natural gas to liquid
gas
1. Fully tighten the bypass screw.
2. Put the knob back.
3. Connect the appliance to the electricity.
26
2. Release the burner injector with a 7 mm
socket spanner and replace it with a right
one.
3. Assemble the burner in a reverse
sequence. Before you fix the screw, make
sure that the burner is pushed correctly to
the back panel.
Test the grill injectors.
B
Levelling
CAUTION!
Remove all the accessories from
the oven.
1. Open the lid of the appliance and
disassemble it.
2. Disassemble the pan supports and all the
burner assemblies.
3. Put the appliance on the sidewall on a
clean and smooth surface. Place each
foot into a separate hole, in the plinth, and
rotate it clockwise.
4. If the floor is not equally flat, use the
adjustable feet on the bottom of the
appliance to set a stable position for the
appliance.
To install all the accessories, do the first step
in an opposite sequence.
Electrical installation
WARNING!
The manufacturer is not
responsible if you do not follow the
safety precautions from Safety
chapters.
This appliance is supplied with a main plug
and a main cable.
27
WARNING!
The power cable must not touch
the part of the appliance shaded in
the illustration.
Environmental concerns
appliances marked with the symbol with the
household waste. Return the product to your
local recycling facility or contact your
municipal office.
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it.
Help protect the environment and human
health by recycling waste of electrical and
electronic appliances. Do not dispose of
28
*
29
30
31
Made in Egypt
867330231-E-462018

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Download PDF

advertisement