ZANUSSI ZCK67201XA User Manual

ZANUSSI ZCK67201XA User Manual
User Manual
GETTING
STARTED?
EASY.
ZCK67201WA
ZCK67201XA
EN User Manual
Cooker
IL
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
WARNING!
Risk of suffocation, injury or permanent disability.
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts are hot.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
•
•
•
•
•
•
2
Only a qualified person must install this appliance and replace
the cable.
This appliance is intended for use up to an altitude of 2000 m
above sea level.
This appliance is not intended to be used on a ships, boats or
vessels.
Do not install the appliance behind a decorative door in order to
avoid overheating.
Do not install the appliance on a platform.
Do not operate the appliance by means of an external timer or
separate remote-control system.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
WARNING: Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire blanket.
CAUTION: The cooking process has to be supervised. A short
term cooking process has to be supervised continuously.
WARNING: Danger of fire: Do not store items on the cooking
surfaces.
Do not use a steam cleaner to clean the appliance.
Do not use harsh abrasive cleaners or sharp metal scrapers to
clean the glass door or the glass of hinged lids of the hob since
they can scratch the surface, which may result in shattering of
the glass.
Metallic objects such as knives, forks, spoons and lids should
not be placed on the hob surface since they can get hot.
Remove any spillage from the lid before opening. Let the hob
surface cool down before closing the lid.
WARNING: The appliance and its accessible parts become hot
during use. Care should be taken to avoid touching heating
elements. Children less than 8 years of age shall be kept away
unless continuously supervised.
Always use oven gloves to remove or put in accessories or
ovenware.
Before maintenance cut the power supply.
Ensure that the appliance is switched off before replacing the
lamp to avoid the possibility of electric shock.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
To remove the shelf supports first pull the front of the shelf
support and then the rear end away from the side walls. Install
the shelf supports in the opposite sequence.
WARNING: Use only hob guards designed by the manufacturer
of the cooking appliance or indicated by the manufacturer of
the appliance in the instructions for use as suitable or hob
guards incorporated in the appliance. The use of inappropriate
guards can cause accidents.
3
SAFETY INSTRUCTIONS
This appliance is suitable for the following markets:
•
IL
INSTALLATION
WARNING! Only a qualified person
must install this appliance.
•
•
•
•
•
•
•
•
•
•
•
•
Remove all the packaging.
Do not install or use a damaged appliance.
Follow the installation instruction supplied with
the appliance.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Do not pull the appliance by the handle.
The kitchen cabinet and the recess must have
suitable dimensions.
Keep the minimum distance from the other
appliances and units.
Make sure that the appliance is installed below
and adjacent safe structures.
Parts of the appliance carry current. Close the
appliance with furniture to prevent touching the
dangerous parts.
The sides of the appliance must stay adjacent to
appliances or to units with the same height.
Do not install the appliance adjacent to a door
or under a window. This prevents hot cookware
to fall from the appliance when the door or the
window is opened.
Make sure to install a stabilizing means in order
to prevent tipping of the appliance. Refer to
Installation chapter.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electrical
shock.
•
•
•
•
•
•
4
All electrical connections should be made by a
qualified electrician.
The appliance must be earthed.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Always use a correctly installed shockproof
socket.
Do not use multi-plug adapters and extension
cables.
Do not let mains cables touch or come near the
appliance door, especially when the door is hot.
•
•
•
•
•
•
The shock protection of live and insulated parts
must be fastened in such a way that it cannot be
removed without tools.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
If the mains socket is loose, do not connect the
mains plug.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type fuses
removed from the holder), earth leakage trips
and contactors.
The electrical installation must have an isolation
device which lets you disconnect the appliance
from the mains at all poles. The isolation device
must have a contact opening width of minimum
3 mm.
Fully close the appliance door, before you
connect the mains plug to the mains socket.
GAS CONNECTION
• All gas connections should be made by a
qualified person.
• Before installation, make sure that the local
distribution conditions (nature of the gas and
gas pressure) and the adjustment of the
appliance are compatible.
• Make sure that there is air circulation around the
appliance.
• The information about the gas supply is on the
rating plate.
• This appliance is not connected to a device,
which evacuates the products of combustion.
Make sure to connect the appliance according
to current installation regulations. Pay attention
to requirements regarding adequate ventilation.
USE
WARNING! Risk of injury and burns.
Risk of electrical shock.
•
•
•
•
•
This appliance is for household use only.
Do not change the specification of this
appliance.
Make sure that the ventilation openings are not
blocked.
Do not let the appliance stay unattended during
operation.
Deactivate the appliance after each use.
•
•
•
Be careful when you open the appliance door
while the appliance is in operation. Hot air can
release.
Do not operate the appliance with wet hands or
when it has contact with water.
Do not use the appliance as a work surface or
as a storage surface.
WARNING! Risk of fire and explosion
•
•
•
•
•
•
Fats and oil when heated can release flammable
vapours. Keep flames or heated objects away
from fats and oils when you cook with them.
The vapours that very hot oil releases can cause
spontaneous combustion.
Used oil, that can contain food remnants, can
cause fire at a lower temperature than oil used
for the first time.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Do not let sparks or open flames to come in
contact with the appliance when you open the
door.
Open the appliance door carefully. The use of
ingredients with alcohol can cause a mixture of
alcohol and air.
WARNING! Risk of damage to the
appliance.
•
•
•
•
•
•
•
•
•
To prevent damage or discoloration to the
enamel:
– do not put ovenware or other objects in the
appliance directly on the bottom.
– do not put water directly into the hot
appliance.
– do not keep moist dishes and food in the
appliance after you finish the cooking.
– be careful when you remove or install the
accessories.
Discoloration of the enamel or stainless steel
has no effect on the performance of the
appliance.
Use a deep pan for moist cakes. Fruit juices
cause stains that can be permanent.
Do not keep hot cookware on the control panel.
Do not let cookware boil dry.
Be careful not to let objects or cookware fall on
the appliance. The surface can be damaged.
Do not activate the cooking zones with empty
cookware or without cookware.
Do not put aluminium foil on the appliance or
directly on the bottom of the appliance.
Cookware made of cast iron, aluminium or with
a damaged bottom can cause scratches.
•
•
•
•
•
•
Always lift these objects up when you have to
move them on the cooking surface.
Provide good ventilation in the room where the
appliance is installed.
Use only stable cookware with the correct
shape and diameter larger than the dimensions
of the burners.
Make sure the flame does not go out when you
quickly turn the knob from the maximum to the
minimum position.
Use only the accessories supplied with the
appliance.
Do not install a flame diffuser on the burner.
This appliance is for cooking purposes only. It
must not be used for other purposes, for
example room heating.
CARE AND CLEANING
WARNING! Risk of injury, fire, or
damage to the appliance.
•
•
•
•
•
•
•
•
•
•
Before maintenance, deactivate the appliance.
Disconnect the mains plug from the mains
socket.
Make sure the appliance is cold. There is the
risk that the glass panels can break.
Replace immediately the door glass panels
when they are damaged. Contact the
Authorised Service Centre.
Be careful when you remove the door from the
appliance. The door is heavy!
Fat and food remaining in the appliance can
cause fire.
Clean regularly the appliance to prevent the
deterioration of the surface material.
Clean the appliance with a moist soft cloth. Only
use neutral detergents. Do not use any abrasive
products, abrasive cleaning pads, solvents or
metal objects.
If you use an oven spray, obey the safety
instructions on the packaging.
Do not clean the catalytic enamel (if applicable)
with any kind of detergent.
Do not clean the burners in the dishwasher.
LID
• Do not change the specification of the lid.
• Clean the lid regularly.
• Do not open the lid, when there are spills on the
surface.
• Before you close the lid turn all burners off.
• Do not close the lid until the hob and oven are
completely cold.
• Glass lid can shatter, when heated (if
applicable).
5
•
•
•
•
INTERNAL LIGHT
• The type of light bulb or halogen lamp used for
this appliance is only for household appliances.
Do not use it for house lighting.
WARNING! Risk of electrical shock.
•
•
•
Contact your municipal authority for information
on how to discard the appliance correctly.
Disconnect the appliance from the mains
supply.
Cut off the mains electrical cable close to the
appliance and dispose of it.
Remove the door catch to prevent children or
pets from becoming trapped in the appliance.
Flat the external gas pipes.
SERVICE
• To repair the appliance contact an Authorised
Service Centre.
• Use original spare parts only.
Before replacing the lamp, disconnect the
appliance from the power supply.
Only use lamps with the same specifications.
DISPOSAL
WARNING! Risk of injury or
suffocation.
INSTALLATION
WARNING! Refer to Safety chapters.
Minimum distances
Dimension
LOCATION OF THE APPLIANCE
You can install your freestanding appliance with
cabinets on one or two sides and in the corner.
Keep a distance of about 1 cm
between the appliance and the back
wall to make sure that the lid opens.
For minimal distances for fitting check the table.
mm
A
400
B
650
C
150
TECHNICAL DATA
Voltage
220 - 240 V
Frequency
50 / 60 Hz
Appliance class
1
B
C
Dimension
A
6
mm
Height
857
Width
600
Depth
600
OTHER TECHNICAL DATA
Appliance category:
I3B/P
Gas original:
G30/G31 (3B/P) 30/30 mbar
BYPASS DIAMETERS
BURNER
Ø BYPASS1) 1/100 mm
Auxiliary
29 / 30
Semi-rapid
32
Multi Crown
67
1) Type of bypass depends on model.
GAS BURNERS FOR LPG G30 30 mbar
BURNER
NORMAL POWER REDUCED POWkW
ER kW
INJECTOR MARK
1/100 mm
NOMINAL GAS
FLOW g/h
Multi Crown
3.2
1.80
90x
233
Semi-rapid
2.0
0.43
71
145
Auxiliary
1.0
0.35
50
73
GAS BURNERS FOR LPG G31 30 mbar
BURNER
Multi Crown
NORMAL POWER kW1)
REDUCED POWER INJECTOR MARK NOMINAL GAS FLOW
1/100 mm
g/h
kW1)
2.8
1.6
90x
200
Semi-rapid
1.7
0.38
71
121
Auxiliary
0.85
0.31
50
61
1) Type of tap depends on model.
GAS CONNECTION
Use a fixed connections or use a flexible stainless
steel pipes in compliance with the regulation in
force. If you use flexible metallic pipes, make sure
they do not come in touch with mobile parts and
they are not squeezed.
WARNING! The gas connection pipe
must not touch the part of the
appliance shown in the illustration.
7
FLEXIBLE NONMETAL PIPES CONNECTION
If you have an easy access to the connection, you
can use a flexible pipe. The flexible pipe must be
tightly attached by clamps.
In installation always use the pipe holder and the
gasket. The flexible pipe can be applied when:
• it can not get hotter than room temperature,
higher than 30 °C,
• it is not longer than 1500 mm,
• it has no narrowing anywhere,
• it is not twisted or tighten,
• it does not get in touch with sharp edges or
corners,
• it's conditions can be easily checked.
When checking the flexible pipe make sure:
• it does not show cracks, cuts, marks of burnings
on the two ends and on its full length,
• the material is not hardened, but shows its
correct elasticity,
• the fastening clamps are not rusted,
• expired term is not due.
If one or more defects are visible, do not repair the
pipe, but replace it.
WARNING! When installation is
complete, make sure that the seal of
each pipe fitting does not leak. To
check the seal use a soap solution, not
a flame.
The gas supply ramp is on the rear side of the
control panel.
The appliance is set to default gas. To
change the setting always use the
gasket sealing.
C
B
A
D
A. Gas connection point (only one point is
applicable for the appliance)
B. Gasket
C. Adjustable connection
D. LPG pipe holder
HOB INJECTORS REPLACEMENT
Replace the injectors when you change the gas
type.
1. Remove the pan supports.
2. Remove the caps and crowns of the burner.
3. Remove the injectors with a socket spanner 7.
4. Replace injectors with the ones necessary for
the type of gas you use.
WARNING! Before you connect the
gas, disconnect the appliance from the
electricity supply or switch off the fuse
in the fuse box. Close the primary
valve of the gas supply.
ADJUSTMENT TO DIFFERENT TYPES OF GAS
Let only an authorized person do the
adjustment to different types of gas.
If the appliance is set for liquid gas
you can change it to natural gas, with
the correct injectors.
The gas rate is adjusted to suit.
WARNING! Before you replace the
injectors, make sure that the gas
knobs are in the Off position.
Disconnect the appliance from the
electrical supply. Let the appliance
cool down. There is a risk of injury.
8
5. Replace the rating plate (it is near the gas
supply pipe) with the one for the new type of
gas supply.
You can find this plate in the bag
supplied with the appliance.
If the supply gas pressure is not constant or it is
different from the necessary pressure, install an
applicable pressure adjuster on the gas supply
pipe.
ADJUSTING THE MINIMUM GAS LEVEL ON
THE HOB BURNER
1. Disconnect the appliance from the electricity.
2. Remove the knob for the hob. If there is no
access to the bypass screw dismount the
control panel before adjustment start.
3. With a thin and flat screwdriver adjust the
bypass screw A.
The model determines the position of the
bypass screw A.
A
ANTI-TILT PROTECTION
Set the correct height and area for the appliance
before you attach the anti-tilt protection.
CAUTION! Make sure you install the
anti-tilt protection at the correct
height.
Make sure that the surface behind the
appliance is smooth.
You must install the anti-tilt protection. If you do not
install it, the appliance can tilt.
Your appliance has the symbol shown on the
picture (if applicable) to remind you about the
installation of the anti-tilt protection.
A
Changing from natural gas to liquid gas
1. Fully tighten the bypass screw.
2. Put the knob back.
Changing from liquid gas to natural gas
1. Unscrew approximately one turn the bypass
screw position A.
2. Put the knob for the hob back.
3. Connect the appliance to the electricity.
4.
5.
6.
7.
8.
WARNING! Put the mains plug
into the mains socket only if all
parts are back into their initial
position. There is a risk of injury.
Light the burner.
Refer to "Hob - Daily use" chapter.
Turn the knob for the hob to the minimum
position.
Remove the knob for the hob again.
Screw on slowly the bypass screw till the flame
becomes minimum and stable.
Put the knob for the hob back on.
LEVELLING OF THE APPLIANCE
1. Install the anti-tilt protection 232 - 237 mm
down from the top surface of the appliance and
110 - 115 mm from the side of the appliance
into the circular hole on a bracket. Screw it into
the solid material or use applicable
reinforcement (wall).
110-115
mm
232- 237
mm
Use small feet on the bottom of appliance to set the
appliance top surface level with other surfaces.
9
2. You can find the hole on the left side at the
back of the appliance. Lift the front of the
appliance and put it in the middle of the space
between the cupboards. If the space between
the bench cupboards is larger than the width of
the appliance, you must adjust the side
measurement to centre the appliance.
This appliance is supplied with a main plug and a
main cable.
WARNING! The power cable must
not touch the part of the appliance
shaded in the illustration.
If you changed the dimensions of the
cooker, you must align the non-tip
device correctly.
CAUTION! If the space between the
bench cupboards is larger than the
width of the appliance, you must
adjust the side measurement to the
centre of the appliance.
ELECTRICAL INSTALLATION
WARNING! The manufacturer is not
responsible if you do not follow the
safety precautions from Safety
chapters.
PRODUCT DESCRIPTION
GENERAL OVERVIEW
1
2 3
4
5
6
4
3
10
10
7
2
8
1
9
1 Knobs for the hob
2 Knob for the Minute Minder
3 Knob for the temperature
4 Temperature indicator / symbol
5 Knob for the oven functions
6 Heating element
7 Lamp
8 Fan
9 Shelf support, removable
10 Shelf positions
COOKING SURFACE LAYOUT
1
2
3
1 Auxiliary burner
2 Steam outlet - number and position depend on
the model
3 Semi-rapid burner
4 Semi-rapid burner
5 Multi Crown burner
5
4
ACCESSORIES
• Wire shelf
For cookware, cake tins, roasts.
• Baking tray
For cakes and biscuits.
• Grill- / Roasting pan
To bake and roast or as pan to collect fat.
• Optional telescopic runners
For shelves and trays. You can order them
separately.
•
Storage compartment
The storage compartment is below the oven
cavity. To use the compartment, lift the lower
front door then pull it down.
WARNING! The storage
compartment can become hot
when the appliance operates.
BEFORE FIRST USE
WARNING! Refer to Safety chapters.
INITIAL CLEANING
Remove all accessories and removable shelf
supports from the appliance.
Refer to "Care and cleaning" chapter.
Clean the appliance and the accessories before
first use.
Put the accessories and the removable shelf
supports back to their initial position.
and the maximum
1. Set the function
temperature.
2. Let the appliance operate for 1 hour.
3. Set the function
and set the maximum
temperature. The maximum temperature for this
function is 210 °C.
4. Let the appliance operate for 15 minutes.
5. Set the function
and set the maximum
temperature.
6. Let the appliance operate for 15 minutes.
Accessories can become hotter than usual. The
appliance can emit an odour and smoke. This is
normal. Make sure that the airflow in the room is
sufficient.
PREHEATING
Preheat the empty appliance to burn off the
remaining grease.
11
HOB - DAILY USE
WARNING! Refer to Safety chapters.
BURNER OVERVIEW
IGNITION OF THE HOB BURNER
A
Always light the burner before you put
on the cookware.
B
WARNING! Be very careful when you
use open fire in the kitchen
environment. The manufacturer
declines any responsibility in case of
the flame misuse.
C
D
1. Turn the knob for the hob counterclockwise to
the maximum gas flow position
and push it
down to light the burner.
2. Keep the knob for the hob pushed for equal or
less than 10 seconds to let the thermocouple
warm up. If not, the gas supply is interrupted.
3. Adjust the flame after it is regular.
A
WARNING! Do not keep the knob
pushed for more than 15 seconds. If
the burner does not light after 15
seconds, release the knob, turn it into
the off position and try to light the
burner again after minimum 1 minute.
B
C
If after some tries the burner does not
light, check if the crown and its cap
are in the correct position.
In the absence of electricity you can
ignite the burner without an electrical
device. In this case approach the
burner with a flame, push the relevant
knob down and turn it to maximum
position. Keep the knob pushed for
equal or less than 10 seconds to let
the thermocouple warm up.
If the burner accidentally goes out,
turn the knob to the off position and try
to light the burner again after minimum
1 minute.
The spark generator can start
automatically when you switch on the
mains, after installation or a power cut.
It is normal.
12
D
A.
B.
C.
D.
Burner cap
Burner crown
Ignition candle
Thermocouple
TURNING THE BURNER OFF
To put the flame out, turn the knob to the off
position
.
WARNING! Always turn the flame
down or switch it off before you
remove the pans from the burner.
HOB - HINTS AND TIPS
WARNING! Refer to Safety chapters.
COOKWARE
WARNING! Do not put the same pan
on two burners.
WARNING! Do not put unstable or
damaged pots on the burner to
prevent from spill and injury.
CAUTION! Make sure that pot
handles are not above the front edge
of the cooktop.
DIAMETERS OF COOKWARE
WARNING! Use cookware with
diameters applicable to the size of
burners.
Burner
Diameter of cookware
(mm)
Multi Crown
160 - 240
Semi - rapid
140 - 240
Auxiliary
120 - 180
CAUTION! Make sure that the pots
are placed centrally on the burner in
order to get maximum stability and to
get lower gas consumption.
HOB - CARE AND CLEANING
WARNING! Refer to Safety chapters.
GENERAL INFORMATION
• Clean the hob after each use.
• Always use cookware with clean bottom.
• Scratches or dark stains on the surface have no
effect on how the hob operates.
• Use a special cleaner applicable for the surface
of the hob.
• Wash stainless steel parts with water, and then
dry them with a soft cloth.
CLEANING THE HOB
• Remove immediately: melted plastic, plastic
foil, sugar and food with sugar. If not, the dirt
can cause damage to the hob. Take care to
avoid burns.
• Remove when the hob is sufficiently cool:
limescale rings, water rings, fat stains, shiny
metallic discoloration. Clean the hob with a
moist cloth and non-abrasive detergent. After
cleaning, wipe the hob dry with a soft cloth.
• To clean the enamelled parts, cap and crown,
wash them with warm soapy water and dry them
carefully before you put them back on.
CLEANING THE SPARK PLUG
This feature is obtained through a ceramic ignition
candle with a metal electrode. Keep these
components well clean to prevent difficult lighting
and check that the burner crown holes are not
obstructed.
PAN SUPPORTS
The pan supports are not resistant to
washing in a dishwasher. They must
be washed by hand.
1. Remove the pan supports to easily clean the
hob.
Be very careful when you replace
the pan supports to prevent the
hob top from damage.
2. The enamel coating occasionally can have
rough edges, so be careful when you wash the
pan supports by hand and dry them. If
necessary, remove stubborn stains with a paste
cleaner.
3. After you clean the pan supports, make sure
that they are in correct positions.
4. For the burner to operate correctly, make sure
that the arms of the pan supports are aligned
with the centre of the burner.
13
PERIODIC MAINTENANCE
Speak to your local Authorised Service Centre
periodically to check the conditions of the gas
supply pipe and the pressure adjuster, if fitted.
OVEN - DAILY USE
WARNING! Refer to Safety chapters.
ACTIVATING AND DEACTIVATING THE
APPLIANCE
It depends on the model if your
appliance has lamps, knob
symbols or indicators:
• The lamp turns on when the
appliance operates.
• The symbol shows whether the
knob controls one of the cooking
zones, the oven functions or the
temperature.
• The indicator turns on when the
oven heats up.
1. Turn the knob for the oven functions to select
an oven function.
2. Turn the knob for the temperature to select a
temperature.
3. To deactivate the appliance, turn the knobs for
the oven functions and temperature to the off
position.
SAFETY THERMOSTAT
Incorrect operation of the appliance or defective
components can cause dangerous overheating. To
prevent this, the oven has a safety thermostat which
interrupts the power supply. The oven activates
again automatically when the temperature drops.
OVEN FUNCTIONS
Symbol
14
Oven functions
Application
Off position
The oven is off.
Conventional Cooking
To bake and roast food on one shelf position.
Bottom Heat
To bake cakes with crispy bottom and to preserve food.
Moist Baking
This function is designed to save energy during cooking.
For the cooking instructions refer to "Hints and tips" chapter, Moist Baking. The oven door should be closed during
cooking so that the function is not interrupted and to ensure that the oven operates with the highest energy efficiency possible. When you use this function, the temperature in the cavity may differ from the set temperature. The
heating power may be reduced. For general energy saving
recommendations refer to "Energy Efficiency" chapter,
Oven - Energy Saving. This function was used to comply
with the energy efficiency class according to EN 60350-1.
Grilling
To grill flat food and to toast bread.
The maximum temperature for this function is 210 °C.
Symbol
Oven functions
Application
True Fan Cooking
To bake on one shelf position and to dry food. Set the temperature 20 - 40 °C lower than for Conventional Cooking.
Defrost
To defrost food (vegetables and fruit). The defrosting time
depends on the amount and size of the frozen food.
OVEN - CLOCK FUNCTIONS
MINUTE MINDER + END OF COOKING
Use it to set an automatic switch-off time for an
oven function.
To operate the appliance manually
without a set time period, turn the
knob for the Minute Minder to
. The
Minute Minder + End of Cooking is
off.
1. Set an oven function and the temperature.
2. Turn the knob for the timer as far as it goes,
then turn it to necessary time period.
After the time period is completed, an acoustic
signal sounds. The appliance deactivates.
Turn the knob for the oven functions and the knob
for the temperature to the off position. Turn the
knob for the timer to
.
OVEN - USING THE ACCESSORIES
WARNING! Refer to Safety chapters.
INSERTING THE ACCESSORIES
Wire shelf:
Put the shelf between the guide bars of the shelf
support.
Tray:
Push the tray or deep pan between the guide bars
of the shelf support. Make sure it does not touch
the back wall of the oven.
Wire shelf and the deep pan together:
Push the deep pan between the guide bars of the
shelf support and the wire shelf on the guide bars
above.
Do not push the baking tray all the way
to the back wall of the cavity. This
prevents the heat from circulating
around the tray. The food may be
burnt, especially in the rear part of the
tray.
15
OVEN - HINTS AND TIPS
WARNING! Refer to Safety chapters.
•
•
The temperature and baking times in
the tables are guidelines only. They
depend on the recipes and the quality
and quantity of the ingredients used.
GENERAL INFORMATION
• The appliance has four shelf positions. Count
the shelf positions from the bottom of the
appliance floor.
• The appliance has a special system which
circulates the air and constantly recycles the
steam. With this system you can cook in a
steamy environment and keep the food soft
inside and crusty outside. It decreases the
cooking time and energy consumption to a
minimum.
• Moisture can condense in the appliance or on
the door glass panels. This is normal. Always
stand back from the appliance when you open
the appliance door while cooking. To decrease
the condensation, operate the appliance for 10
minutes before cooking.
• Clean the moisture after each use of the
appliance.
• Do not put the objects directly on the appliance
floor and do not put aluminium foil on the
components when you cook. This can change
the baking results and cause damage to the
enamel.
BAKING
• Your oven may bake or roast differently to the
appliance you had before. Adapt your usual
16
•
•
settings such as temperature, cooking time and
shelf position to the values in the tables.
Use the lower temperature the first time.
If you cannot find the settings for a special
recipe, look for the similar one.
Cakes and pastries at different heights do not
always brown equally at first. If this occurs, do
not change the temperature setting. The
differences equalize during the baking
procedure.
Trays in the oven can twist during baking. When
the trays become cold again, the distortions
disappear.
BAKING CAKES
• Do not open the oven door before 3/4 of the set
cooking time is up.
COOKING MEAT AND FISH
• Use a deep pan for very fatty food to prevent the
oven from stains that can be permanent.
• Leave the meat for approximately 15 minutes
before carving so that the juice does not seep
out.
• To prevent too much smoke in the oven during
roasting, add some water into the deep pan. To
prevent the smoke condensation, add water
each time after it dries up.
COOKING TIMES
Cooking times depend on the type of food, its
consistency, and volume.
Initially, monitor the performance when you cook.
Find the best settings (heat setting, cooking time,
etc.) for your cookware, recipes and quantities
when you use this appliance.
CONVENTIONAL COOKING
Food
Quantity (g)
Temperature
(°C)
Time (min)
Shelf position
Accessories
Pastry stripes
250
150
25 - 30
3
baking tray
Flat cake 1)
1000
160 - 170
30 - 35
2
baking tray
Yeast cake with
apples
2000
170 - 190
40 - 50
3
baking tray
Drip pan cake
1500
160 - 170
45 - 55 2)
2
baking tray
Chicken, whole
1350
200 - 220
60 - 70
2
wire shelf
1
baking tray
3
wire shelf
1
baking tray
3
Wire shelf
1
baking tray
Chicken, half
1300
190 - 210
35 + 30
Pork roast cutlet
600
190 - 210
30 - 35
Flan bread 3)
800
230 - 250
10 - 15
2
baking tray
Stuffed yeast
cake 4)
1200
170 - 180
25 - 35
2
baking tray
Pizza
1000
200 - 220
25 - 35
2
baking tray
Cheese cake
2600
170 - 190
60 - 70
2
baking tray
Swiss apple
flan 4)
1900
200 - 220
30 - 40
1
baking tray
Christmas
cake 4)
2400
170 - 180
55 - 65 5)
2
baking tray
Quiche Lorraine 4)
1000
220 - 230
40 - 50
1
1 round tray (diameter: 26 cm)
Peasant bread 6)
750 + 750
180 - 200
60 - 70
1
2 aluminized
trays (length: 20
cm)
Romanian
sponge cake 1)
600 + 600
160 - 170
40 - 50
2
2 aluminized
trays (length: 25
cm) on the same
shelf position
Romanian
sponge cake traditional
600 + 600
160 - 170
30 - 40
2
2 aluminized
trays (length: 25
cm) on the same
shelf position
Yeast buns 4)
800
200 - 210
10 - 15
2
baking tray
17
Food
Quantity (g)
Temperature
(°C)
Time (min)
Shelf position
Accessories
Swiss roll 1)
500
150 - 170
15 - 20
1
baking tray
Meringue
400
100 - 120
40 - 50
2
baking tray
Crumble cake 4)
1500
180 - 190
25 - 35
3
baking tray
Buttered cake 1)
600
180 - 200
20 - 25
2
baking tray
1) Preheat the oven for 10 minutes.
2) After you switch off the appliance, leave the cake in the oven for 7 minutes.
3) Preheat the oven for 20 minutes.
4) Preheat the oven for 10 - 15 minutes.
5) After you switch off the appliance, leave the cake in the oven for 10 minutes.
6) Set the temperature for 250 °C and preheat the oven for 18 minutes.
TRUE FAN COOKING
Food
Temperature
(°C)
Time (min)
Shelf position
Accessories
Pastry stripes 1)
250
155
20
3
baking tray
Flat cake 1)
1000
155
35
2
baking tray
Yeast cake with
apples 1)
2000
170 - 180
40 - 50
3
baking tray
Apple pie 1)
1200 +
1200
175
55
1
2 round aluminized trays
(diameter: 20
cm)
Small cakes 1)
500
150
35
3
baking tray
Fatless sponge
cake 1)
350
160
30
3
1 round aluminized tray
(diameter: 26
cm)
Drip pan cake
1200
150 - 160
40 - 50 2)
3
baking tray
Chicken, whole
1400
200
50
2
wire shelf
1
baking tray
Pork roast cutlet
600
180 - 200
30 - 40
2
wire shelf
1
baking tray
2
baking tray
Flan bread 3)
18
Quantity (g)
800
230 - 250
10 - 15
Food
Quantity (g)
Temperature
(°C)
Time (min)
Stuffed yeast
cake
1200
160 - 170
20 - 30
Cheese cake
2600
150 - 170
Swiss apple
flan 3)
1900
180 - 200
Christmas
cake 1)
2400
Quiche Lorraine 3)
Shelf position
Accessories
3
baking tray
60 - 70
2
baking tray
50 - 40
3
baking tray
150 - 170
50 - 60 4)
3
baking tray
1000
210 - 230
35 - 45
2
1 round tray
(diameter: 26
cm)
Peasant bread 5)
750 + 750
180 - 190
50 - 60
3
baking tray
Romanian
sponge cake 1)
600 + 600
150 - 170
40 - 50
2
2 aluminized
trays (length:
25 cm) on
the same
shelf position
Romanian
sponge cake traditional
600 + 600
160 - 170
30 - 40
2
2 aluminized
trays (length:
25 cm) on
the same
shelf position
Yeast buns 1)
800
190
15
3
baking tray
Swiss roll 1)
500
150 - 170
10 - 15
3
baking tray
Meringue
400
100 - 120
50 - 60
2
baking tray
Crumble cake 1)
1500
170 - 180
20 - 30
2
baking tray
Sponge cake 1)
600
150 - 170
20 - 30
2
baking tray
1) Preheat the oven for 10 minutes.
2) After you switch off the appliance, leave the cake in the oven for 7 minutes.
3) Preheat the oven for 15 minutes.
4) After you switch off the appliance, leave the cake in the oven for 10 minutes.
5) Set the temperature to 230 °C and preheat the oven for 15 minutes.
MOIST BAKING
Food
TemperaShelf poTime (min)
ture (°C)
sition
Accessories
Bread and pizza
19
Food
TemperaShelf poTime (min)
ture (°C)
sition
Accessories
Buns
190
25 - 30
2
baking tray or grill- / roasting pan
Bread rolls
200
40 - 45
2
baking tray or grill- / roasting pan
Frozen pizza 350 g
190
25 - 35
2
wire shelf
Swiss roll
180
20 - 30
2
baking tray or grill- / roasting pan
Brownie
180
35 - 45
2
baking tray or grill- / roasting pan
210
35 - 45
2
six ceramic ramekins on wire shelf
Sponge flan base
180
25 - 35
2
flan base tin on wire shelf
Sponge cake
150
35 - 45
2
cake tin on wire shelf
Fish in pouches 300 g
180
25 - 35
2
baking tray or grill- / roasting pan
Whole fish 200 g
180
25 - 35
2
baking tray or grill- / roasting pan
Fish fillet 300 g
180
30 - 40
2
pizza pan on wire shelf
Cakes in baking tray
Cakes in tin
Soufflé
Fish
Meat
Meat in pouch 250 g
200
35 - 45
2
baking tray or grill- / roasting pan
Meat skewers 500 g
200
30 - 40
2
baking tray or grill- / roasting pan
Cookies
170
25 - 35
2
baking tray or grill- / roasting pan
Macarons
170
40 - 50
2
baking tray or grill- / roasting pan
Muffins
180
30 - 40
2
baking tray or grill- / roasting pan
Savoury cracker
160
25 - 35
2
baking tray or grill- / roasting pan
Shortcrust pastry biscuits
140
25 - 35
2
baking tray or grill- / roasting pan
Tartelettes
170
20 - 30
2
baking tray or grill- / roasting pan
Mixed vegetables in
pouch 400 g
200
20 - 30
2
baking tray or grill- / roasting pan
Omelette
200
30 - 40
2
pizza pan on wire shelf
Vegetables on tray
700 g
190
25 - 35
2
baking tray or grill- / roasting pan
Small baked items
Vegetarian
20
INFORMATION FOR TEST INSTITUTES
Temperature (°C)
Accessories
Shelf posiTime (min)
tion
Food
Function
Small cakes (16 per
tray)
Conventional
Cooking
160
baking tray
3
20 - 30
Small cakes (16 per
tray)
Fan Cooking
150
baking tray
3
20 - 30
Small cakes (16 per
tray)
True Fan
Cooking
160
baking tray
1+3
30 - 40
Apple pie (2 tins Ø20
cm, diagonally off
set)
Conventional
Cooking
190
wire shelf
1
60 - 75
Apple pie (2 tins Ø20
cm, diagonally off
set)
Fan Cooking
180
wire shelf
2
70 - 80
Fatless sponge cake
Conventional
Cooking
180
wire shelf
2
20 - 30
Fatless sponge cake
Fan Cooking
160
wire shelf
2
25 - 35
Fatless sponge cake
True Fan
Cooking
170
wire shelf
1+3
30 - 40
Short bread / Pastry
stripes
Conventional
Cooking
140
baking tray
3
15 - 30
Short bread / Pastry
stripes
Fan Cooking
140
baking tray
3
20 - 30
Short bread / Pastry
stripes
True Fan
Cooking
140
baking tray
1+3
15 - 30
Toast
Fast Grilling
250
wire shelf
3
5 - 10
Beef burger
Turbo Grilling
250
wire shelf or
grill- / roasting
pan
3
15 - 20
first
side; 10
-15
second
side
PIZZA SETTING
When you cook Pizza, for best results
turn the control knobs for oven
functions and oven temperature to the
Pizza position.
21
OVEN - CARE AND CLEANING
WARNING! Refer to Safety chapters.
NOTES ON CLEANING
• Clean the front of the appliance with a soft cloth
with warm water and a cleaning agent.
• To clean metal surfaces, use a dedicated
cleaning agent.
• Clean the appliance interior after each use. Fat
accumulation or other food remains may result
in a fire. The risk is higher for the grill pan.
• Clean stubborn dirt with a special oven cleaner.
• Clean all accessories after each use and let
them dry. Use a soft cloth with warm water and
a cleaning agent.
• If you have nonstick accessories, do not clean
them using aggressive agents, sharp-edged
objects or a dishwasher. It can cause damage
to the nonstick coating.
STAINLESS STEEL OR ALUMINIUM
APPLIANCES
Clean the oven door with a damp cloth
or sponge only. Dry it with a soft cloth.
Do not use steel wool, acids or
abrasive materials as they can damage
the oven surface. Clean the oven
control panel with the same
precautions.
1
2
Install the shelf supports in the opposite sequence.
CLEANING THE OVEN DOOR
The oven door has two glass panels. You can
remove the oven door and the internal glass panel
to clean it.
The oven door can close if you try to
remove the internal glass panel before
you remove the oven door.
CAUTION! Do not use the appliance
without the internal glass panel.
1. Open the door fully and hold the two door
hinges.
REMOVING THE SHELF SUPPORTS
To clean the oven, remove the shelf supports.
1. Pull the front of the shelf support away from the
side wall.
2. Lift and turn the levers on the two hinges.
2. Pull the rear end of the shelf support away from
the side wall and remove it.
22
6. Turn the two fasteners by 90° and remove them
from their seats.
3. Close the oven door halfway to the first
opening position. Then pull forward and remove
the door from its seat.
90°
7. First lift carefully and then remove the glass
panel.
4. Put the door on a soft cloth on a stable surface.
5. Release the locking system to remove the
internal glass panel.
1
2
8. Clean the glass panel with water and soap. Dry
the glass panel carefully.
When the cleaning is completed, install the glass
panel and the oven door. Do the above steps in the
opposite sequence.
The screen-printing zone must face the inner side
of the door. Make sure that after the installation the
surface of the glass panel frame on the screenprinting zones is not rough when you touch it.
Make sure that you install the internal glass panel in
the seats correctly.
23
WARNING! Danger of electrocution!
Disconnect the fuse before you
replace the lamp.
The lamp and the lamp glass cover
can be hot.
REPLACING THE LAMP
Put a cloth on the bottom of the interior of the
appliance. It prevents damage to the lamp glass
cover and the cavity.
1. Deactivate the appliance.
2. Remove the fuses from the fuse box or
deactivate the circuit breaker.
The back lamp
1. Turn the lamp glass cover counterclockwise to
remove it.
2. Clean the glass cover.
3. Replace the lamp with a suitable 300 °C heatresistant lamp.
4. Install the glass cover.
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
WHAT TO DO IF...
Problem
Remedy
There is no spark when you try
to activate the spark generator.
The hob is not connected to an
electrical supply or it is connected incorrectly.
Check if the hob is correctly
connected to the electrical
supply. Refer to the connection
diagram.
There is no spark when you try
to activate the spark generator.
The fuse is blown.
Make sure that the fuse is the
cause of the malfunction. If the
fuse is blown again and again,
contact a qualified electrician.
There is no spark when you try
to activate the spark generator.
Burner cap and crown are
placed incorrectly.
Place the burner cap and
crown correctly.
The flame extinguishes immediately after ignition.
Thermocouple is not heated up
sufficiently.
After lightning the flame, keep
the spark generator activated
for equal or less than 10 seconds
The flame ring is uneven.
Burner crown is blocked with
food residues.
Make sure that the injector is
not blocked and the burner
crown is clean.
The burners do not work.
There is no gas supply.
Check the gas connection.
The flame colour is orange or
yellow.
24
Possible cause
The flame can look orange or
yellow in some areas of the
burner. This is normal.
Problem
Possible cause
Remedy
The lamp does not operate.
The lamp is defective.
Replace the lamp.
Steam and condensation settle
on the food and in the cavity of
the oven.
You left the dish in the oven for
too long.
Do not leave the dishes in the
oven for longer than 15 - 20
minutes after the cooking
process ends.
The oven does not heat up.
The necessary settings are not
set.
Make sure that the settings are
correct.
It takes too long to cook the
dishes or they cook too quickly.
The temperature is too low or
too high.
Adjust the temperature if necessary. Follow the advice in the
user manual.
SERVICE DATA
If you cannot find a solution to the problem yourself,
contact your dealer or an Authorised Service
Centre.
The necessary data for the service centre is on the
rating plate. The rating plate is on the front frame of
the appliance cavity. Do not remove the rating plate
from the appliance cavity.
We recommend that you write the data here:
Model (MOD.)
.........................................
Product number (PNC)
.........................................
Serial number (S.N.)
.........................................
ENERGY EFFICIENCY
HOB - ENERGY SAVING
You can save energy during everyday cooking if you
follow below hints.
• When you heat up water, use only the amount
you need.
• If it is possible, always put the lids on the
cookware.
• Before you use the burners and pan support
make sure they are assembled correctly.
• The cookware bottom should have the correct
diameters for the burner size.
• Put the cookware directly over the burner and in
the centre of it.
• When the liquid starts to boil, turn down the
flame to barely simmer the liquid.
• If it is possible, use a pressure cooker. Refer to
its user manual.
OVEN - ENERGY SAVING
The oven contains features which help
you save energy during everyday
cooking.
General hints
Make sure that the oven door is closed properly
when the oven operates. Do not open the door too
often during cooking. Keep the door gasket clean
and make sure it is well fixed in its position.
Use metal dishes to improve energy saving.
When possible, do not preheat the oven before you
put the food inside.
When the cooking duration is longer than 30
minutes, reduce the oven temperature to minimum
3 - 10 minutes before the end of the cooking time,
depending on the duration of the cooking. The
residual heat inside the oven will continue to cook.
25
Moist Baking
Use the residual heat to warm up other dishes.
Keep breaks between baking as short as possible
when you prepare few dishes at one time.
Function designed to save energy during cooking.
For additional details refer to "Oven - Daily use"
chapter, Oven functions.
Cooking with fan
When possible, use the cooking functions with fan
to save energy.
Keep food warm
Choose the lowest possible temperature setting to
use residual heat and keep a meal warm.
ENVIRONMENTAL CONCERNS
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
Recycle materials with the symbol
. Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
26
*
27
867342593-A-302018
WWW.ZANUSSI.COM/SHOP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement