Electrolux Z4709A User Manual

IMPORTANT INFORMATION
2–4
Upright Vacuum Cleaner Owner’s Guide
Household Type
Z4700 Series
4
GUARANTEE
5
QUICK REFERENCE
5–8
HOW TO ASSEMBLE
9–10
11
ROUTINE MAINTENANCE
11
Empty Dust Cup
11
Clean Dust Cup Filter
12
PERIODIC MAINTENANCE
12
Brushroll
12
Brushroll Belt
IMPORTANT
Please read these
instructions for
advice on the
HOW TO USE
13–15
PROBLEM SOLVING
13
Clear Hose
13
Thermal Cut Off
14
Mini Turbo Nozzle
maintenance of
your cleaner.
FILTER REPLACEMENT CODE: EF86b
www.electrolux.co.uk
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
IMPORTANT INFORMATION
To reduce the risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner whilst plugged in. Turn off the switch and unplug the electrical cord when not in
use and before servicing.
• Do not place cleaner on furniture or stairs as the brushroll may cause damage.
Place cleaner on floor with the handle in the storage position while using attachments.
• This appliance is not intended for use by any persons (including children) with reduced physical, sensory or mental
capabilities, or a lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, damaged,
left outdoors, or dropped into water, return it to a service centre before using.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
Do not run vacuum cleaner over cord. Keep cord away from heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that
may reduce airflow.
• This vacuum cleaner creates suction and contains a revolving brushroll. Keep hair, loose clothing, fingers, and all parts
of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without the dust cup or filter(s) in place.
• Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive belt.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.
• Store your cleaner indoors in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming them.
PLEASE SAVE THESE INSTRUCTIONS
The symbol
on the product or on its packaging indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
2
BEFORE YOU START
CHECK THE VOLTAGE
Before connecting the cleaner to an electrical supply, ensure that the voltage shown on the rating plate located beneath the cleaner
is of the correct voltage for your electricity supply. If it is not, do not use the cleaner but refer back to your dealer.
CONNECTING TO YOUR ELECTRICITY SUPPLY
IMPORTANT INFORMATION
Permanently connected to the cleaner is a mains supply (2-core) cable fitted with a non-rewirable plug incorporating a 13A fuse.
In the event of the fuse requiring replacement the fuse cover should be removed using a small screwdriver. The old fuse MUST
be replaced by a 13A ASTA approved BS1362 fuse or a BSI approved fuse. The cover must be replaced before the plug is used
again. In the event of loss of the fuse cover, replacements can be obtained from your Electrolux Retailers and must be of the
same colour as indicated by the coloured insert on the base of the plug.
If difficulty is experienced in obtaining a replacement, contact Electrolux Customer Services on 08445 614614. Calls to this number
will be charged at 5p per minute at all times from a BT Landline.
In no circumstances must the plug be used without a correct fuse cover fitted.
If the plug that is fitted to your appliance is not suitable for your socket outlet, it must be cut off and the appropriate plug fitted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to prevent the hazard of shocks in case it should be plugged into a 13 amp socket
in another part of your home.
The wires in the mains cable of this appliance are coloured in accordance with the following code: Blue: Neutral. Brown: Live.
As the colours of the wires in the mains cable of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
If using a three-pin plug, do not make any connection to the terminal marked with the letter E or by the earth symbol or coloured
green or green-and-yellow. This cleaner is double insulated and no earth connection is necessary.
It is in your interest to ensure that the plug is correctly attached to the mains cable. In case of doubt, consult a qualified electrician,
as Electrolux cannot regard the repair of faults on the plug connection as a service that can be given free of charge under the
terms of the guarantee.
13 Amp Fuse
13 Amp
Fuse
Cover
Fuse
WARNING
Blue
Brown
Cord
Clamp
The brush in the cleaning head rotates at high speed and can cause damage to the mains supply cable if the cleaner passes
over it during cleaning operations.
Care should be taken to ensure that this does not happen. If the cleaning head has accidentally passed over the mains supply cable
the following action should be taken:
1. Switch off and remove the plug from the socket outlet.
2. Examine the mains supply cable for damage (only after removing the plug from the socket outlet).
3. If the supply cord is damaged it must be replaced by a Electrolux Service Agent or similar qualified person in order to avoid a
hazard.
4. NEVER use the machine with a damaged mains supply cable.
Proprietary carpet conditioning and air freshening materials
After using proprietary carpet conditioning powders, it is recommended that the filters be changed. Some of these preparations contain
substances which, if left in the vacuum cleaner for extended periods, could damage the plastic mouldings which form the structure of
the cleaner.
Many air fresheners, household deodorants, sprays and polishes contain a highly flammable gas propellant.
Because of this, it is particularly important that these products are used strictly in accordance with the relevant manufacturer’s
instructions.
It is essential that none of the above products are sprayed directly into the vacuum cleaner or any of its filters, hose assembly, dustbag
chamber or dust cup.
Thermal Cut Off
This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner switches off, push the
switch pedal once and unplug the cleaner. Check the cleaner for a possible source of overheating such as a full dust cup, a blocked hose or
clogged filter. If these conditions are found, fix them and wait at least 30 minutes before attempting to use the cleaner. After the 30 minute
period, plug the cleaner back in and push the on/off switch On (I). If the cleaner still does not run, please call Electrolux Customer Care.
3
SERVICE
Should you require service on your Electrolux cleaner, please telephone Electrolux Customer Services on 08445 614614. Calls
to this number will be charged at 5p per minute at all times from a BT Landline. Before requesting service, please check
whether your problem is covered under Service Checklist (see below). Electrolux will arrange the uplift of the product for repair
should no local service agent be available.
New filter pads, brushrollers and drive belts can be obtained from Electrolux Retailers. If difficulty is experienced in obtaining
spares, please contact Electrolux on 08445 614614. Calls to this number will be charged at 5p per minute at all times from
a BT Landline.
IMPORTANT INFORMATION
SERVICE CHECKLIST
• If your cleaner will not operate, check the plug connection, plug fuse and mains fuse.
• Never allow the dust cup to become so full that it impedes the airflow, thus reducing the cleaning efficiency of the machine.
The character of household dust and its effect on the airflow through the machine may vary considerably. Fluffy dust allows
air to pass through readily whereas fine powdery dust or proprietary cleaning powders, pack tightly in the dust cup, offering
greater resistance to air flow and will reduce cleaning efficiency if the cup becomes overloaded.
• Always store your cleaner and spare dust filters in a dry place.
• Renew the filter pads three or four times a year. This is essential to ensure continued high filtration of dust particles.
• Sucking up such items as stockings, clippings of cloth, sizeable pieces of paper, wrappings from cigarette packets or sweets
etc., may block the hose. Electrolux regrets that the clearing of blocked hoses cannot be regarded as service that can
be given free of charge, under the guarantee. Should a blockage occur, first disconnect the cleaner from the electricity
supply, refer to section headed “Blockages.” If these operations are not successful, contact Electrolux on 08445 614614.
Calls to this number will be charged at 5p per minute at all times from a BT Landline.
• Never pick up hot cinders or lighted cigarette ends.
• Make certain that your cleaner does not come into contact with water or any other liquid. It is not designed as a wet
pick up cleaner, and must never be used on damp carpets or wet floors.
Important - If the supply cord is damaged it must be replaced by a Electrolux Service Agent or similar qualified person in order
Spares
New filters, brushrollers and drive belts can be obtained from Authorised Electrolux Dealers and electrical retailers. If difficulty
is experienced in obtaining spares please call us on 08445 614614 (Calls to this number will be charged at 5p per minute at all
times from a BT Landline) or visit our website at www.shop.electrolux.co.uk
GUARANTEE
GUARANTEE
This guarantee is in addition to your statutory and other legal rights.
This product is for household use only.
Electrolux products are carefully designed, manufactured, tested and inspected and, in consequence, we undertake to replace or repair
any part found to be defective in materials or workmanship, within one year of delivery to the original purchaser, free of charge. You
may be required to take the product to your nearest service provider if the product requires attention during the first year.
There are certain conditions which may invalidate this guarantee:
a. It is dependent upon the appliance being correctly installed and used in accordance with the Company’s instructions under normal
domestic conditions within the United Kingdom or the Republic of Ireland.
b. Service at all times must be carried out by an Electrolux Service Representative or authorised agent.
c. The guarantee may be invalidated by unauthorised repair or modification of the appliance.
d. You may be charged by Electrolux if you call for an engineer to resolve a problem that we believe is covered in the instruction booklet.
(example: blocked/dirty filters)
Electrolux does not accept liability for all defects arising from neglect, misuse or accident. This guarantee excludes such normal wearing
parts as drive belts, brushes and filters as the life of these depends upon the amount and nature of use.
Proof of purchase will be required before service under guarantee is provided. Please call �������������������������������������������
08445 614614�������������������������������
for assistance. ��������������
Calls to this
number will be charged at 5p per minute at all times from a BT Landline.
IMPORTANT:
For future reference we suggest you record the following details here, and keep the receipt with the handbook as proof of purchase.
Purchased from_____________________________________________________
Date purchased___________________Model no___________________________
101 Oakley Road, LUTON, BEDFORDSHIRE, LU4 9QQ
Features of the Electrolux vacuum cleaner and accessories supplied with it are protected in Great Britain and abroad by Patents or Registered
Designs.
This appliance conforms with the requirements of the amended E.E.C. directive No. 89/336/EEC relating to electromagnetic compatibility
(EMC) CE.
Electrolux may introduce modifications to their product from time to time, and consequently the details given in this booklet are subject to
alteration without notice.
4
Quick Reference
B
C
E
F
G
A
Wand
B
Crevice Tool
C
Dusting Brush
D
Hose
E
Base
F
Dust Cup with Lid and Filter
G
Handle ( G1 Turbo Handle)
H
Tool Caddy
I
Rear Housing
J
Hose Retainer
K
Stair Brush
G1
QUICK REFERENCE
A
D
K
H
Stair Brush (some models only)
J
I
How To Assemble
CAUTION: Assemble the cleaner completely before using.
NOTE: All screws must be installed to properly secure the
parts of the vacuum.
CAUTION: Moving parts, make sure the on/off switch is in
the off position and stay clear of the brushroll
when plugging in.
L1 l
L2 l
NOTE: Features may vary by model yet all parts assemble
the same.
Remove all components from the carton and check that all of the parts
are available from the parts list above.
(NOT provided in the package)
HOW TO ASSEMBLE
Have a Phillips screwdriver available (one is NOT provided in the
package).
5
How To Assemble (continued)
FIG. 1
I to the base l
E Step 1: Assemble the rear housing l
by sliding it on top of the base and attaching to the base
L2 . (FIG. 1)
using a long screw provided l
lI L2
l
E l
HOW TO ASSEMBLE
H to the top of the rear
Step 2: Attach the tool caddy l
I
housing l by sliding it onto the housing, lining up the
screw holes, and then attaching it using the 2 short
L1 provided. (FIG. 2)
screws l
l
L1 l
L1 FIG. 2
H l
lI FIG. 3
G to top of tool caddy l
H by
Step 3: Attach the handle l
sliding it downward and then securing with a long screw
L2 . (FIG. 3)
l
G l
L2 l
H l
6
How To Assemble (continued)
FIG. 4
D to the hose
Step 4: Secure the hose assembly l
I with 2 short screws
connection on the rear housing l
L1
l (FIG. 4).
D l
L1 l
l
I L1 l
FIG. 5
lI L1 l
J l
Step 6: Pull the electrical cord up to the cord retainer
and firmly push into the retainer (FIG. 6a). This will keep
the cord out of the way for next use. Wrap the cord
around the carrying handle on the tool caddy and then
wrap around the cord release hook. (FIG. 6)
HOW TO ASSEMBLE
Step 5: Thread the hose inside the lower hose retainer
J and then attach the lower hose retainer to the rear
l
I with a short screw l
L1 (FIG. 5).
housing l
FIG. 6
FIG. 6a
7
How To Assemble (continued)
Step 7: Then wrap the hose up and over the hose hook
G as shown. Plug the end of the hose
on the handle l
E (FIG. 7a)
into the hose retainer hole on the base l
and then snap the hose into the hose holder on the
H . (FIG. 7b)
tool caddy l
FIG. 7
FIG. 7a
G
l
H
l
E
l
FIG. 7b
HOW TO ASSEMBLE
F on the vacuum by aligning
Step 8: Place the dust cup l
the bottom groove of the dust cup against the tab on
cleaner base. Pivot the dust cup up against cleaner and
push to secure as it snaps into place. (FIG. 8)
Step 8A: (in some models only). Place stair brush in
slot in the special handle holder. (FIG. 8a)
FIG. 8
FIG. 8a
F
l
A /l
B tool in the
Step 9: Place the wand/crevice l
wand holder on the side of the vacuum. Store the
C on the brush holder on the back
dusting brush l
of the handle. (FIG. 9)
FIG. 9
l
B
A
l
8
C
l
How To Use
FIG. 10
CAUTION:Do not plug in cleaner until
you understand all controls
and features.
Plug in Vacuum (FIG. 10). Unwrap the cord by
turning the quick release cord hook (FIG. 10a),
unwind the cord and plug into an appropriate
outlet.
Put Cord on Cord Retainer. To use, push
electrical cord down into cord retainer (FIG. 11a).
You will find your cord retainer on the handle
above the upper cord hook. This will place the
cord out of the way the next time you vacuum.
(FIG. 11)
FIG. 10a
ON/OFF Switch Pedal
FIG. 11
CAUTION:Cleaner with revolving
brushrolls may not be suitable
for some types of carpet. If in
doubt, please check with the
carpet manufacturer.
FIG. 11a
Cleaner Height Setting (FIG. 12a)
The cleaner has an adjustment that raises or
lowers the cleaner base to match the type of floor
surface. With the cleaner cord unplugged, set the
adjustment to lowest setting for maximum carpet
cleaning. If the cleaner is difficult to push, move
adjustment to next highest setting until cleaner
FIG. 12a
is comfortable to push. The brushroll must
reach the carpet for effective cleaning. For ease
in moving the adjustment knob, place handle in
operating position and tilt cleaner back to remove weight
from front wheels.
WARNING:Avoid injury. Keep loose clothing,
hair, fingers, and all other parts of
body away from any moving part
(such as the revolving brush).
HOW TO USE
The ON/OFF Switch Pedal is on the base. Press once
to turn on and press again to turn off. (FIG.12). Due to
the powerful motor fitted to this vacuum, you may notice
a higher level of noise than that of your previous model,
and that it will pick up considerably more than your
old model. You may need to empty the dustbin more
frequently as a result of this better pickup.
FIG. 12
9
How To Use (continued)
Stair Cleaning
When cleaning stairs, do not place the cleaner on the stairs or
on a stair above you. This unit is fitted with a constantly rotating brush roll. Care should be taken when using the hose to
clean stairs that the back - not the front - of the unit is placed
against the base of the stairs. This will prevent the unit leaning
forward and causing possible damage to carpets or floors. An
additional stair hose can be purchased. When attached to the
hose on the cleaner you can clean a full flight of stairs without
moving the cleaner. Contact our Customer Care representatives by calling 08445 614614. Calls to this number will be
charged at 5p per minute at all times from a BT Landline.
CAUTION: Do not place the cleaner on stairs or on
a stair above you when cleaning stairs.
FIG. 14
Use Handle Release
14a
Step on handle release (FIG. 14a) and pull handle back to a
comfortable position. Press again to lower handle further to
clean under furniture. Return to full upright position to use the
hose and attachments. (FIG. 14)
Before cleaning under low furniture, check area first for objects that
might harm the unit or block the
vacuum hose.
How To Use Accessories
CAUTION: Do not place the cleaner on furniture
or steps for any period of time as the
brush roll may cause damage. Place the
cleaner on the floor with the handle in
the upright/storage position while using
the accessories.
FIG. 15
B
l
Remove hose from hose adapter on the base of cleaner.
Place desired accessory onto end of hose or wand.
A to add reach. Grasp both
Nested Extension Wand l
wands near ridges. Pull apart. Turn ridge end to center.
Push wands together. (FIG. 15)
B cleans corners, baseboards and between
Crevice Tool l
cushions.
C is for furniture, blinds,
Dusting/Upholstery Brush l
books, lampshades, shelves, curtains, draperies, cushions
and fabrics.
10
NOTE: When using on hard floors an additional
hard floor nozzle is available. Please ring
Electrolux Customer Care on 08706 055 055.
Call to this number will be charged at 5p per
minute at all times from a BT Landline.
C
l
A
l
HOW TO USE
Helpful hINT:
Routine Maintenance
NOTE: Turn off the switch and unplug the electrical cord
before routine maintenance. Never operate the
vacuum cleaner without the dust cup filter in place.
FIG. 16
16a
Empty Dust Cup
Lift up the latch and pull out to release the dust cup from the
housing. Press the button as shown in (FIG. 16a) to empty the dust
from the bottom of the cup.
Clean Dust Cup Filter, EF86b
Cleaning the Pleated Filter:
Emptying The Dust Cup:
It is clearly visible when the dust cup is full and needs emptying.
There is a fill line to help determine when the cup is full. Remove dust
cup from cleaner body, remove the lid and dump debris in a waste
container.
Reinstalling The Dust Cup:
To mount the filter assembly into cleaner body, make certain the filter
assembly is fully seated in top of dust cup lid (FIG. 18). Replace dust
cup by aligning front of the bottom of dust cup into groove on cleaner.
Pivot dust cup up against cleaner and push in place until the dust cup
latch is secure.
FIG. 18
Clean Dust Cup Filter
CAUTION: The dust cup can be washed in warm water, if
desired, but strong detergents should not be used.
Dry thoroughly before using again.
FIG. 17
Empty Dust Cup
NOTE: Frequent cleaning of the filters will maintain
maximum efficiency of your cleaner. The pleated
17a
filter should be removed for frequent washing and
can be used in rotation with a spare filter to ensure a
clean, dry filter is always ready for use.
Step 1: Remove the dust cup lid assembly by turning the lid counter
clockwise (move to OPEN position) (Fig. 17a) then grasp dust
cup lid and pull dust cup lid out and away from the cup (Fig. 17b).
Step 2: Grasp the pleated filter and turn counter clockwise to remove. 17b
(FIG. 17)
Step 3: Shake off dust and hair from filter into the trash. Brush inbetween pleats to remove dust and debris. To wash, rinse
only with warm water. Shake excess water from filter. Do not
submerge filter assembly.
Step 4: When all parts are completely dry, replace pleated filter and
turn clockwise to lock in place.
Step 5: Allow filter to dry for 24 hours before reusing.
ROUTINE MAINTENANCE
NOTE: Turn off the switch and unplug the electrical cord
before changing the Pleated Filter. Never operate the
vacuum cleaner without the dust cup or the pleated
filter assembly. To maintain good performance,
check the Pleated Filter each time the dust cup
is emptied and clean if needed. The filter can be
cleaned by rinsing it with warm water. Be sure
pleated filter is completely dry before reinstalling.
11
PERIODIC Maintenance
CAUTION: Turn off the switch and unplug the electrical
cord before replacing belt. Motor shaft can
become hot during normal use. To prevent
injury, avoid touching the motor shaft when
checking the belt. (FIG. 20 )
PERIODIC MAINTENANCE
Brushroll
The brushroll turns as it sweeps and combs the carpet nap. Remove
hair and threads from the brushroll so it continues brushing the
carpet. To maintain the most efficient cleaning, the bristles must
touch the carpet. To test the bristle length, hold a ruler against the
underneath side of the cleaner. If the bristles no longer touch the
ruler, replace the brushroll.
19a
Brushroll Belt
Brushroll Performance Window (FIG. 19). To check condition
of the belt watch to see if white dots on the belt are moving
through the performance window (FIG. 19a). This indicates
the brushroll is turning.
The brushroll belt turns the brushroll to agitate, sweep, and comb
the carpet nap. Check the belt regularly to be sure it is in good
condition. Replace the belt if it stretches, cracks or loses tension.
Cut away any hair or threads wound around the brushroll or the
belt pulley because the buildup could cause the belt to rotate
unevenly.
FIG. 19
NOTE: Care should be taken when vacuuming rugs to
ensure that edges and fringes do not snap the
drive belt and stop the rotation of the brush roll.
To Change Belt
Step 1: Lower handle to floor to change belt.
Step 2: Remove two screws to release hood (FIG. 19).
Lift hood to expose belt and brushroll (FIG. 20).
Motor
Shaft
Step 3: Lift right side of brushroll and pull out of base.
Brushroll
Step 4: Remove and discard belt.
Brushroll Belt
Step 7: Place belt around right side of brushroll.
Step 5: Clean debris from brushroll area. Clean any
burnt rubber from motor shaft using fine
sandpaper or an emery board.
Step 6: Place new belt around motor shaft.
Step 8: Pull right side of brushroll to stretch belt. Secure
right end cap into base.
Step 9: Align left end cap with square in base. Push end cap
into place.
Step 10: Rotate brushroll to position belt on brushroll pulley.
Step 11: Replace the hood.
Step 12: Tighten screws.
12
FIG. 20
NOTE:Use only GENUINE ELECTROLUX
replacement brushroll belt, Code ZE090.
PLEASE NOTE:The new belt will be
smaller in diameter
compared with the used
belt. Therefore, it will
require stretching into
place. This is normal.
PROBLEM SOLVING
How to Check and Clear Hose Blockages
Low suction or poor pick-up may be due to a
blockage in the vacuum cleaner.
Step 1: Remove hose from hose retainer on the
base and check suction at end of hose. If
little or no suction, check dust cup. Empty
if needed. If no improvement, proceed to
step 2.
Clear Hose
CAUTION: Turn off the switch and unplug
the electrical cord before
clearing hose.
Thermal Cut-Off
This cleaner has a special thermostat that protects
the cleaner in case of motor overheating. If the
cleaner suddenly turns off, follow this procedure:
FIG. 21
Thermal Cut Off
Step 2: Remove electrical cord from cord hooks.
Disconnect the clear tube by unscrewing
the 2 screws, then lift away from cleaner.
Check for any obstructions that may be
in the tube or hose. Obstructions may be
removed by using a blunt instrument to
clear the tube or hose. Flexing the hose
may help loosen the blockage. After
clearing blockage, reverse above steps to
reassemble unit. (FIG. 21)
Step 1: Push on/off switch to off.
Step 2: Unplug cleaner.
Step 3: Check for source of overheating problem
(i.e. full dust cup, clogged hose or clogged
filters).
Step 4: If a full dust cup, clogged hose or clogged
filters are found, empty the dust cup,
unclog the hose or replace the filters.
Step 5: Wait at least 30 minutes before attempting
to reuse the cleaner.
Step 6: After a 30-minute cool down period, plug
the cleaner in and push the switch pedal.
The cleaner should turn on.
Step 7: If the cleaner still does not operate,
please call Electrolux Customer Care on
08445 614614. Calls to this number will
be charged at 5p per minute at all times
from a BT Landline.
13
Models equipped with Mini Turbo Nozzle
(on some models) A Mini Turbo Nozzle can be purchased by contacting our Customer Care representatives by calling 08445 614614. Call to this number will be
charged at 5p per minute all times from a BT Landline.
This convenient air-driven Turbo Nozzle is perfect for
use on upholstery, stairs and area rugs. Turbo Nozzle is
designed for use on end of hose.
Maintenance Instructions:
PROBLEM SOLVING Mini Turbo Nozzle
To remove any clogs or debris from around the
brushroll or belt of the turbo, follow the steps
below:
Step 1: To open Turbo Nozzle, unscrew
the two (2) screws on the side (as
pictured).
Step 2: Lift up the bottom housing.
Step 3: Clear blockage from brushroll area.
Step 4: To close align top and bottom housings
and tighten with the two (2) screws.
14
Screws
Problem
Cause
Filter
Belt Brushroll
Hose
No suction at the hose.
Dust Cup and Filter
Hose
Noise from the brushroll area.
Brushroll
Belt
Cleaner is hard to push.
Cleaner Height Setting
Cleaner height knob will not turn.
Cleaner Height Setting
Brushroll will not turn.
Brushroll
Burning smell.
Belt
Stair brush doesn't work.
Brushroll/Belt
Missing parts.
• Push plug securely into outlet.
• Try another outlet.
• Check circuit breaker.
• Refer to page 3.
• Refer to page 13.
• Empty the dust cup.
• Make sure dust cup is installed properly and
dust cup latch is secured.
• Make sure pleated filter is clean.
• Replace broken, loose, out-of-shape belt.
• Clean hair and thread from bristles and end
cap area.
• Replace brushroll if bristles are worn.
• Remove any clogs from the hose that restrict
the air flow.
• Refer to pages 11, 12, and 13.
• Empty the dust cup.
• Clean and install filter properly.
• Make sure dust cup is installed properly and
dust cup latch secured.
• Remove any clogs from the hose that restrict
the air flow.
• Check both ends of the hose.
• Refer to pages 11 and 13.
• Remove hood and clean debris from the
brushroll area.
• Replace broken, loose, out-of-shape belt.
• Refer to page 12.
• Put handle in operating position. Tilt the
cleaner back to raise the front wheels off the
floor. Then turn the knob to a higher setting.
• Refer to page 9.
• Hint: Put handle in operating position. Tilt the
cleaner back to raise the front wheels off the
floor. Then turn the knob.
• Replace broken, loose, out-of-shape belt.
• Refer to pages 9 and 12.
• Remove hood and clean debris from the
brushroll area.
• Refer to page 12.
• Remove hood and clean debris from the
brushroll and belt area.
• Refer to page 12.
• Remove any clogs from the opening or debris
around the brushroll or belt.
• Refer to page 14.
• Call Electrolux on 08445 614614. Call to this
number will be charged at 5p per minute
at all times from a BT Landline. Have the
model and serial numbers ready when you
call. See rating plate beneath the cleaner.
PROBLEM SOLVING
Motor will not start.
Electric Plug
Motor suddenly stops. Thermal Cut Off
Does not clean the carpet/floor.
Dust Cup Solution
More questions?
15
If you experience any problems with your cleaner,
don’t struggle taking it back to the shop.
Call our dedicated Customer Helpline for help and
advice and also to order filters and accessories.
08445 614614
Call to this number will be charged at 5p per minute at all times from a BT landline.
Items in this Carton
Handle
Rear
Housing
Dusting
Brush
Screws
Base
Wand
Dust Cup with
Lid and Filter
Stair Brush
(on some
models only)
Hose
Tool
Caddy
Hose
Retainer
Crevice Tool
Thank you for purchasing
an Electrolux cleaner.
Don’t Forget to Use
Genuine Electrolux Parts
Caution:Damages caused by the use of non-genuine parts
are not covered by the Electrolux Guarantee.
Part No. 75598D (09/06)
Printed in PRC
">