Frigidaire GLHV36T5KC User Manual

Frigidaire GLHV36T5KC User Manual
OWNER’S GUIDE
GLHV30T4KC - GLHV30T4KW
GLHV36T5KC - GLHV36T5KW
READ AND SAVE THESE INSTRUCTIONS
Contents
Product Registration .................................................................................... 2
Important Safety Instructions ..................................................................... 3
Installation ................................................................................................4-6
Use and Care ................................................................................................ 7
Hood Cleaning ............................................................................................. 8
Lights Replacement ..................................................................................... 8
Warranty ..................................................................................................... 10
Range Hood
P/N 316 137 203
LI1NTA
Product Registration
Register your Product
The self-addressed P R O D U C T
REGISTRATION CARD should be
filled in completely, signed and
returned to the Frigidaire Canada.
Thank you for choosing this appliance. The information contained within
this Owner’s Guide will instruct you on how to properly operate and care for
your range hood. Please read through the information contained in your
literature pack to learn more about your new appliance.
Record Your Model and Serial Numbers
Record in the space provided below the model and serial numbers found on
the serial plate located on the right hand side of the range hood.
Model Number: ___________________________________________________
Serial Number: ___________________________________________________
Date of Purchase: _________________________________________________
This Owner’s Guide contains general
operating instructions for your range
hood and feature information for
several models. Your range hood
may not have all the described
features.
Note: The instructions appearing in
this Owner’s Guide are not meant to
cover every possible condition and
situation that may occur. Common
sense and caution must be practiced
when installing, operating and
maintaining any appliance.
2
Important Safety Instructions
READ AND SA
VE THESE INSTRUCTIONS
SAVE
Take care when using cleaning agents or detergents.
Suitable for use in household cooking area
CAUTION - To reduce risk of fire and to properly exhaust air, be sure to duct air outside – Do not vent exhaust
air into spaces within walls or ceilings or into attics, crawl spaces, or garages.
CAUTION - For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And
Vapors.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means
to prevent power from being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a prominent warning device, such as a tag, to the service panel.
WARNING – TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
b. Always turn hood ON when cooking at high heat or when cooking flaming foods.
c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
d. Use proper pan size. Always use cookware appropriate for the size of the surface element.
WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:
a. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL
TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b. NEVER PICK UP A FLAMING PAN – You may be burned.
c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
d. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction.
b) Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and
safety standards such as those published by the National Fire Protection Association (NFPA), and the American
Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
c) When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d) Ducted fans must always be vented to the outdoors.
WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
WARNING
Electrical Shock Hazard - Can result in serious injury or death.
Disconnect appliance from electric power before servicing.
If equipped, the fluorescent light bulb contains small amounts of mercury which
must be recycled or disposed of according to Local, State, and Federal Codes.
3
Installation
FOR RESIDENTIAL USE ONLY
NOT TO BE INSTALLED OVER GAS GRILLS
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Safety Warning: Turn off power circuit at the service entrance and lock out
panel, before wiring this appliance.
Requirement: 120 V AC, 60 Hz. 15 or 20 A
Dimensions
Weight: 30” Model 34 lbs - 36” Model 38,5 lbs
Diameter of Transition 4” 3/4
Figure 1
Diameter of exhaust Duct required 4” 3/4
Considerations before installing Hood
1. For the most efficient air flow exhaust, use a straight run or as few elbows
as possible.
CAUTION: Vent unit to outside of building, only.
2. If allowed in your area, use metallic flex ducting only to connect rigid duct
directly to transitions.
3. COLD WEATHER installations should have an additional backdraft damper
installed to minimize backward cold air flow and a nonmetallic thermal
break to minimize conduction of outside temperatures as part of the
ductwork. The damper should be on the cold air side of the thermal break.
The break should be as close as possible to where the ducting enters the
heated portion of the house.
4. Hood installation height above cooktop is the users preference. The lower
the hood above the cooktop, the more efficient the capturing of cooking
odors, grease and smoke. We recommends the hood be installed 18,5”
minimum above an electric cooktop or 25,6” minimum above a gas
cooktop . Be sure that your hood model fits your installation.
4
Installation
Pre-Installation consideration
Tools required for installation
Screw driver (pozidrive n°2 )
Electric drill
with twist bit Ø 2 mm and Ø 6 mm
The hood can be installed to be used in the following ways:
• External exhausting version
• Recycling version (with carbon filter to be ordered from your supplier)
External Exhausting Version
B
The air is expelled outside by means of a pipe to be connected to the coupling
ring B (Figure 2).
In horizontal runs, the duct must be slightly slanted (about 10°) and directed
upwards to vent the air easily from the room to the outside.
A non-return smoke valve is supplied as an optional to be mounted on the
coupling flange .
Recycling version
Figure 2
E
The air is filtered through a carbon filter and recycled into the room.
If the hood has no filter ask for one from the technical assistance service or
the manufacturing company, specifying the hood model.
To install the filter, insert it in the place provided and use the two hooks D
to fasten it (Figure 4).
The filtered air is discharged above the wall cabinet through the baffle E , to
be fastened by means of two screws provided directly on the vertical of the
outlethole of the hood (if necessary fit a duct Ø120mm from the coupling
flange to the upper edge of the hole provided on the top side of the
cupboard (Figure 3).
Figure 3
Figure 4
5
Installation
Fastening the hood to the wall cabinet
Fit the drilling template, which comes with the hood, on the inner right side
of the cabinet making sure side “A” coincides with back part.
Make at least two 2 mm. diameter holes at points 1-2 (Figure 5).
Perform the same operations on the inner left side.
Use screws F (4.5x16) to fasten the hood to the cabinet (Figure 6).
Attention! While mounting the hood on the wall cabinet be sure once the
hood has been fastened, to allow the wiring compartment to be easily and
safely reachable, in order to make eventual safety inspections and/or
maintenance operations.
Box adjustment
Figure 5
The hood can be installed in cabinets with different depths; the front of the
box must always be in line with the cabinet.
For alignment, adjust the back stops of the box.
For box adjustment, loosen screws M , slide the square plates P as necessary,
and tighten screws M (Figure 7).
Ensure that the drawer, when fully retracted, turns OFF all power by acting
positively on the rear microswitch.
F
Wiring to Power Supply
WARNING!
ELECTRICAL GROUNDING INSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION BOX WITH
3 WIRES, ONE OF WHICH (GREEN/YELLOW) SERVES TO GROUND THE
APPLIANCE. TO PROTECT YOU AGAINST ELECTRIC SHOCK, THE GREEN
AND YELLOW WIRE MUST BE CONNECTED TO THE GROUNDING WIRE
IN YOUR
HOME ELECTRICAL SYSTEM, AND IT MUST UNDER NO CIRCUMSTANCES
BE CUT OR REMOVED.
Figure 6
M
Warning: Turn off power circuit at the service panel before wiring this unit.
120 VAC, 15 or 20 Amp circuit required.
P
Figure 7
a.
Remove j-box cover as shown in Figure 8.
b.
Remove the knockout and install the strain relief (conduit) connector (1/
2") in junction box.
c.
Run 3 wires; black, white and green (#16 AWG) in 1/2" conduit from
service panel to junction box.
d.
Connect black wire from service panel to black or red in junction box,
white to white and green to green-yellow. See Figure 8.
e.
Close junction box cover, check all light bulbs to make sure they are
secure in their sockets, then turn power on in service panel and check
lights and blower operation per Care & Use section of this manual and
install filters.
f.
Make sure to leave this manual for the home owner.
Figure 8
6
Use and Care
Control Pad Functions
READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE RANGE HOOD.
For satisfactory use of your hood, become familiar with the various functions
of the hood as described below
Air outlet
Motor
Housing
Light OFF
Light ON
Motor
Housing
Very High Suction Power
High Suction Power
Grease Filters
Handles
Lamp Shield
(PL lamp Housing)
Mid Suction Power
Grease
Filters
Low Suction Power
Motor OFF
Figure 9
Operating Instructions
The blower should be turned on for about 5 minutes before cooking in order to establish air currents upward through
the hood.
Use the low speeds for normal use and the higher speeds for strong odors or fumes.
Minimize cross drafts which will reduce the effectiveness of the hood.
7
Hood Cleaning
Be sure lights are cool before cleaning the hood.
To Clean Filters
• The metal grease filters will last forever.
They are made of anodized aluminum
• It is recommended that the filters be washed at least once a month; they
can be washed by hand or in the dishwasher.
• Drain water through edge holes and let each filter dry thoroughly before
replacing it.
To Remove The Metal Grease Filters
• Turn blower and lights off.
• Push simultaneously the two handles S first upwards, then towards the
center and extract the filters Figure 10.
Figure 10
To Replace The Metal Grease Filters
• Reverse procedure.
To Replace The Carbon Filter
• The Carbon Filter must be replaced once a yera in normal use.
• To dismount push the two locks D and extract it from its housing.
To Clean Hood Surface
Figure 11
• For general care, wipe the outside of the stainless steel, white, black or
glass hood with sudsy water or household cleaners such as Fantastic® or
Formula 409®, rinse well and dry with clean soft cloth to avoid water marks.
• Wipe and dry brushed stainless steel in the same direction as the grain.
• Do not use abrasive products.
• To remove finger prints and give added shine use spray cleaners such as
Stainless Steel Magic® and Shimmer®.
Lights replacement
R
Q
G
NOTE: Turn blower and lights off. Make sure the lights are cool. If new
lights do not operate be sure lights are inserted correctly before calling
service.
• Remove the light shield Q by pushing simultaneously the two unlocking
buttons R (Figure 12); for safety reasons make sure to remove the light
shield from its suspension slides G .
• Pull out fluorescent tube and replace with Philips Type PL-S 9 Watt
maximum.
• Refit the light shield.
Figure 12
8
9
RANGE HOOD WARRANTY
Your range hood is protected by this warranty
In the U.S.A., your appliance is warranted by Electrolux Home Products North America, a division of White Consolidated Industries, Inc. We
authorize no person to change or add to any of our obligations under this warranty. Our obligations for service and parts under this warranty must
be performed by us or an authorized Electrolux Home Products North America servicer. In Canada, your appliance is warranted by WCI Canada,
Inc.
*NORMAL
This warranty applies only to products in ordinary household use, and the consumer is responsible for the
RESPONSIBILITIES items listed below:
OF THE CONSUMER 1. Proper use of the appliance in accordance with instructions provided with the product.
2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in
accordance with all local plumbing, electrical and/or gas codes.
3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose
connections or defects in house wiring.
4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,etc.,
which are not a part of the appliance when it was shipped from the factory.
5. Damages to finish after installation.
6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).
This warranty does not cover the following:
EXCLUSIONS
1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this
limitation or exclusion may not apply to you.
2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in
ordinary household use. The consumer shall pay for such service calls.
3. Damages caused by services performed by servicers other than Electrolux Home Products North America or its
authorized servicers; use of parts other than genuine Electrolux Home Products parts; obtained from persons
other than such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God.
4. Products with original serial numbers that have been removed or altered and cannot be readily determined.
IF YOU NEED
Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the
SERVICE
warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all
receipts. This written warranty gives you specific legal rights. You may also have other rights that vary from state to state.
Service under this warranty must be obtained by contacting Electrolux Home Products:
This warranty only applies in the 50 states of the U.S.A., Puerto Rico, and Canada. Product features or specifications as described or illustrated are
subject to change without notice. All warranties are made by Electrolux Home Products North America, a division of White Consolidated Industries,
Inc. In Canada, your appliance is warranted by WCI Canada, Inc.
03-U-RH-02
Canada
866•213•9397 (English)
866•294•9911 (French)
Electrolux Home Products North America
6150 McLaughlin Road
Mississauga, Ontario, Canada
L5R 4C2
USA
800•944•9044
Electrolux Home Products North America
P.O. Box 212378
Augusta, GA 30917
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement