Zanussi | ZRW110N | User manual | ZANUSSI ZRW110N User Manual

EN
User manual
Wine refrigerator
ZRW110N
The following symbols are used in this manual:
Important information concerning your personal safety and information on how to avoid damaging the
appliance.
General information and tips
Environmental information
2
Contents
Safety information_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Operation_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Maintenance _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Technical information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
3
5
5
6
7
Customer service and spare parts _ _ _ _ _ _ _ _ _
Electrical connection _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
What to do if... _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Environment concerns_ _ _ _ _ _ _ _ _ _ _ _ _ _ _
7
8
9
12
12
Subject to change without notice
Safety information
It is most important that this instruction book should
be retained with the appliance for future reference.
Should the appliance be sold or transferred to another
owner, or should you move house and leave the
appliance, always ensure that the book is supplied
with the appliance in order that the new owner can be
acquainted with the functioning of the appliance and
the relevant warnings.
If this appliance featuring magnetic door seals is to
replace an older appliance having a spring lock (latch)
on the door or lid, be sure to make that spring lock
unusable before you discard the old appliance. This will
prevent it from becoming a death-trap for a child.
These warning are provided in the interest of safety.
You must read them carefully before installing or using
the appliance.
General Safety
The appliance is designed exclusively for domestic use.
The appliance is intended to be used exclusively for
the storage of the wine as explained in this instruction
booklet.
WARNING!
Risk of injury due to broken glass! In case
of transport at an altitude of over 1100 m
the glass panes of the door may break. The
door may break. The fragments have sharp
edges and may cause serious injury. Take
appropriate protective action.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
• It is dangerous to alter the specifications or modify
this product in any way.
• Before any cleaning or maintenance work is carried
out, be sure to switch off and unplug the appliance.
• This appliance is heavy. Care should be taken when
moving it.
• Take utmost care when handling your appliance so
as not to cause any damages to the cooling unit
with consequent possible fluid leakages.
• The appliance must not be located close to radiators
or gas cookers.
• Avoid prolonged exposure of the appliance to direct
sunlight.
• There must be adequate ventilation round the
appliance and any damage to the refrigerant circuit
must be avoided.
• Do not use other electrical appliances (such as ice
cream makers) inside of refrigerant appliance.
Service/Repair
• Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
• This product should be serviced by an authorized
Service Center, and only genuine spare parts should
be used.
• Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out by
inexperienced persons may cause injury or more
serious malfunctioning. Refer to your local Service
Centre, and always insist on genuine spare parts.
• This appliance contains hydrocarbons in its cooling
unit; maintenance and recharging must therefore
only be carried out by authorized technicians.
3
Use
Installation
• The domestic wine refrigerator is designed to be
used specifically for the storage of potable wine
only.
Important: For electrical connection carefully follow
the instructions given in specific paragraphs.
• Best performance is obtained with ambient
temperature as follows:
Climate class
Ambient temperature
SN
+10°C to +32°C
N
+16°C to +32°C
ST
+16°C to +38°C
T
+16°C to +43°C
T he class of your appliance is shown on its rating
plate.
• Warning: when the ambient temperature is not
included within the range indicated for the class of
this appliance, the following instructions must be
observed: when the ambient temperature rises up
the maximum level, the storage temperature in the
refrigerator cannot be guaranteed, it is advisable to
use the food stored as soon as possible.
• Do not put hot pot on the plastic parts of the
appliance.
• Do not store flammable gas and liquid in the
appliance, because they may explode.
• Do not place wine directly against the real wall of
compartment.
• The appliance’s manufactures storage
recommendations should be strictly adhered to.
Refer to relevant instructions.
• The inner lining of the appliance consists channels
through which the refrigerant passes. If these
should be punctured this would damage the
appliance beyond repair and cause food loss. DO
NOT USE SHARP INSTRUMENTS to scrape of frost
or ice. Frost may be removed by using a scraper.
Under no circumstances should be solid ice be
forced off the liner. Solid ice should be allowed to
thaw when defrosting the appliance.
4
• Unpack the appliance and check if there are
damages on it. Do not connect the appliance if it is
damaged. Report possible damages immediately to
the place you bought it. In that case retain packing.
• During normal operation, the compressor and/
or condenser at the back of the appliance heat
up considerably. For safety reasons, minimum
ventilation must be as shown in the instructions.
Attention: keep ventilation openings clear of
obstruction.
• Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cord is damaged, it must
be replaced by a special cord or assembly available
from the manufacture or its service agent.
• If the appliance is transported horizontally, it is
possible that the oil contained in the compressor
flows in the refrigerant circuit. It is advisable to wait
at least two hours before connecting the appliance
to allow the oil to flow back in the compressor.
• There are working parts in this product which heat
up. Always ensure that there is adequate ventilation
as a failure to do this will result in component failure
and possible loss. See installation instructions.
• Parts which heat up should not be exposed.
Wherever possible the back of the product should
be against a wall.
Environment Protection
This appliance does not contain gasses which could
damage the ozone layer, in either its refrigerant circuit
or insulation materials. The appliance shall not be
discarded together with the urban refuse and rubbish.
The insulation foam contains flammable gasses: the
appliance shall be disposed according to the applicable
regulations to obtain from your local authorities. Avoid
damaging the cooling unit, especially at the rear
near the heat exchanger. The materials used on this
appliance marked by the symbol are recyclable.
Use
Cleaning the interior
Do not use detergents or abrasive powders,
as these will damage the finish.
Before using the appliance for the first time, wash the
interior and all internal accessories with lukewarm
water and some neutral soap so as to remove the
typical smell of a brand-new product, and then dry
naturally and thoroughly.
Control panel
Display
A
B
C
D
E
A - temperature up key
B - temperature down key
C - display
D - °F and °C exchanging key
E - light On/Off key
1
2
3
1 - wine storage type
2 - temperature indicator
3 - °F or °C indicator
Operation
After inserting the plug in the socket, the wine
refrigerator will run immediately.
Use
Wine arrangement
Temperature regulation
Please place the wine bottles as the below picture.
Press “∧” key to increase the temperature.
Press “∨” key to decrease the temperature.
The correct position must in any case be determined
bearing in mind that the inside temperature depends
on these factors:
• Room temperature
• How often the door is opened
• The quantity of bottles stored
• The position of the appliance
Maximum loading capability of each shelf is
10 standard bottles.
Keep the wine in the dark. The door is in anti-UV
darkened triple glass to protect the wine from the light
in case the refrigerator is located in well-lit place.
5
Lay the bottles down in such a way that the corks
do not dry.
Avoid switching the appliance light on too often
or for too long. Wine keeps better in dark.
Handle the bottles with care, to avoid agitating the
wine.
Follow the recommendations and advice received
at the time of purchase or given in the technical
documentation regarding the quality, duration and
optimum storage temperature of the wine.
1. The interior light will be on automatically for
5 minutes when the wine refrigerator is powered
on.
2. The interior light can be turned on or off by press
the light On/Off key.
3. Interior light will be switched on immediately when
the door is open. And it will be off automatically
after the door has been open for ten minutes.
4. Interior light will be switched off after the door is
close for 5 minutes.
Storage advice
°F/°C exchange
The storage time for wine depends on ageing, the type
of grapes, alcoholic content and level of fructose and
tannin contained in it. At the time of purchase, check if
the wine is already aged or if it will improve over time.
The temperature can exchanged from °F to °C by
press °F/°C exchanging key.
Recommended storage temperature:
– For champagne and sparkling wines, between 6 and
8 °C
Switching off
Unplug the refrigerator to switch it off.
Inside accessories Shelves
The shelves can be removed for cleaning.
– For white wines, between 10 and 12 °C
– For rose and light red wines, between 12 and 16 °C
– Aged red wines, 14-16 °C
When placing various bottles on top of each
other, make sure they do not touch the refrigerator
cooling plate.
Bottle “Light On”
The bottle can be lighted on by the interior light as
below ways.
Maintenance
Unplug the appliance before carrying out any
operation.
Important
This appliance contains hydrocarbons in the refrigerant
circuit; therefore maintenance and recharging must
only be carried out by personnel authorized by the
manufacturer.
Defrosting
Defrosting in the refrigerator compartment occurs
automatically. The defrost water is run into a bowl
located at the back of the appliance, above the
compressor, where it evaporates. Make sure to
6
periodically clean the defrost water drain hole, using
the special “cleaner”.
Cleaning
Cleaning the inside, removing the shelves, with
lukewarm water and a mild detergent.
Periodically clean the defrost water drain hole, using a
special “cleaner”.
Periodically clean motor compressor with a brush or
vacuum cleaner. This operation will improve operation,
with consequent energy saving. During periods when
the appliance is not being used, take the following
precautions:
– unplug the appliance;
Important
Never use metal objects to clean the appliance.
Lamp replacement safety instructions
For safety reasons this appliance is provided with
special lamps specifically tested and certified for the
foreseen use.
They can only be replaced with lamps of the same type
and having the same characteristics.
Replacement lamps must be done only from authorized
customer service.
– defrost and clean the inside and all the accessories;
– leave the door ajar to prevent the formation of
unpleasant odours.
Technical Information
Net fridge capacity lt.
110
Energy consumption kWh/24h
0.542
Energy consumption kWh/year
198
Dimensions mm
High
850
Width
500
Depth
552
The technical information are situated in the rating plate on the internal left side of the appliance.
Customer service and spare parts
If the appliance is not functioning properly, check that:
• the plug is firmly in the wall socket and the mains
power switch is on;
• there is an electricity supply (find out by plugging in
another appliance);
• If there are water drops on the bottom of the
cabinet, check that the defrost water drain opening
is not obstructed (see “Defrosting” section).
• If the power cable is damaged, it must be replaced
with a special cable or assembly available from the
manufacture or the technical assistance service.
To obtain fast service, it is essential that when
you apply for it you specify the model and
serial number of your appliance which can be
found on the guarantee certificate or on the
rating plate located inside the appliance, on
the bottom left-hand side.
• If your appliance is still not working properly after
making the above checks, contact the nearest
service centre.
7
Electrical connection
Before plugging in, ensure that the voltage and
frequency shown on the serial number plate
correspond to your domestic power supply. Voltage can
vary by ±6% of the rated voltage. For operation with
different voltages, a suitably sized auto-transformer
must be used.
The wires in the mains lead are coloured in
accordance with the following code:
The appliance must be earthed
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The power supply cable plug is provided with a contact
for this purpose. If the domestic power supply socket is
not earthed, connect the appliance to a separate earth
in compliance with current regulations, consulting a
specialist technician.
The Manufacturer declines all responsibility if
the above safety precautions are not observed.
This appliance complies with the
E.E.C. Directives.
1
2
3
5
4
8
1 Green and Yellow:Earth
3 Brown:
Live
5 Blue:
Neutral
1. Connect the wire coloured green and yellow to the
terminal marked either with the letter “E” or by the
earth symbol
or coloured green and yellow.
2. Connect the wire coloured blue to the terminal
either marked with the letter “N” or coloured black.
3. Connect the wire coloured brown to the terminal
either marked with the “L” or coloured red.
4. Check that no cut, or stray strands of wire is
present and the cord clamp 4 is secure over the
outer sheath.
5. Make sure the electricity supply voltage is the
same as that indicated on the appliance rating
plate.
6. Switch on the appliance. The appliance is supplied
with a 13 amp plug fitted 2 . In the event of
having to change the fuse in the plug supplied, a
13 amp ASTA approved (BS 1362) fuse must be
used.
Warning! A cut off plug inserted into a 13 amp
socket is a serious safety (shock) hazard. Ensure
that it is disposed of safely.
Installation
3. Remove the two screw covers.
Important
In order to reserve the required space around the
refrigerator for ventilation, please keep 100mm
distance between 2 sides and top of the wine
refrigerator and the wall and 50mm distance between
rear of refrigerator and the wall.
100
50
4. Remove the two screws and take the handle off.
Put the handle at a safe place.
100
Door reversibility
Before carrying out any operations, remove the
plug from the power socket. To change the opening
direction fo the door, proceed as follows:
1. Remove the tow screws at the rear of the top
cover.
5. Move the hole covers from the left side to the right
side.
2. Push the top cover forward until it is free. And
move the small plate from left to right. Then put
the top cover on a safe place to avoid scratch.
9
6. Unscrew the hinge screws and remove the hinge,
then lift the door and put it on a padded surface to
avoid scratch. Put the hinge and the screws in a
safe place.
7. Remove the cover of door as the rotation direction
shown in the below picture. And then put it on the
other side of the door.
9. Fix the handle on the left side, insert the plastic
cover that can be found in bag for use instruction.
10.Lay the appliance on a soft rug or similar article to
protect it. Unscrew and remove the lower hinge pin
and install it to other hole.
11.Unscrew the screws that fix the lower hinge and
take the lower hinge with foot off.
8. Rotate the door, then unscrew the screw and
transfer the stopper to other side. Then securely fix
the stopper with screw.
10
12.Move the foot from left to right and fix it in right
hole show in below picture.
13.Fix the lower hinge with screws on the other.
16. Fixed the top cover by the two screws.
Levelling
14.Put the door on the lower hinge. Keep the door
cling the cabinet and put the upper hinge into
the hinge hole. The right and left side of the door
must align with the sides of the cabinet. And then
securely fix the upper hinge.
The appliance should be level in order to eliminate
vibration. There are 4 height adjustable feet at bottom
of the appliance, 2 feet in the front and 2 feet in the
back. To make the appliance level, it should be upright
and all feet should be firmly contacted with the floor.
Warning: Reposition, level the appliance, wait for
at least four hours and then connect it to the power
socket. In case you do not want to carry out the above
mentioned operations, contact the nearest After Sales
Service Force. The After Sales Service specialist will
carry out the reversibility of the doors at your cost.
Warning: After having reversed the opening direction
of the door check that all the screws are properly
tightened and that the magnetic seal adheres to the
cabinet If the ambient temperature is cold (i.e. in
Winter), the gasket may not fit perfectly to the cabinet.
In that case, wait for the natural fitting of the gasket.
Lay down the appliance back side down.
15. Place the top cover on the top of the refrigerator
and push it to back side until it is hooked by the
fixed blocks.
11
What to do if...
Warning: Before troubleshooting, disconnect
the power supply. Only a qualified electrician of
competent person must do the troubleshooting
that is not in this manual.
Malfunction
The wine is too warm.
Important: There are some sounds during
normal use (compressor, refrigerant circulation).
Possible cause
Remedy
Temperature is not properly
adjusted.
Please look in the “Use” section.
Door was open for an extended
period.
Open the door only as long as necessary.
The appliance is near a heat
source.
Please look in the “Installation” section.
Interior lighting does not work.
Light bulb is defective.
Please look in the “Maintenance” section.
Heavy build up of the frost,
possibly also on the door seal.
Door seal is not air tight (possibly Carefully warm the leaking sections of
after changing over the hinges). the door seal with a hair dryer (not hotter
than approx. 50 °C). At the same time
shape the warmed door seal by hand
such that it sits correctly.
Unusual noises.
Appliance is not level.
Readjust the feet.
The appliance is touching the
wall or other objects.
Move the appliance slightly.
A component, e.g. a pipe, on
rear of the appliance is touching
another part of the appliance or
the wall.
If necessary, carefully bend the
component out of the way.
The compressor does not start
immediately after changing the
temperature setting.
This is normal, no error has
occurred.
The compressor starts after a period of
time.
Water on the floor.
Water drain hole is blocked.
See the “Cleaning” section.
Environment concerns
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
12
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
Download PDF

advertising