Zanussi | FJS1025W | User manual | ZANUSSI FJS1225W User Manual

ZANUSSI FJS1225W User Manual
124970982.qxd
9/4/01
2:49 AM
Pagina
1
(Nero/Process Black pellicola)
WASHING MACHINE
FJS 1025 W
FJS 1225 W
FJS 1425 W
DELA
MP
ER A
T
SP
IN S P
FJS 1025 W
PREWASH
SUPER
RINSE
RINSE
HOLD
RE
E
E
OP
TIO N
S
SKIP
QUICK
TI M
V
E
FA BR T
IC
HAND
124970982
1200
900
700
500
90°
60°
50°
40°
30°
COTTONS
SYNTHETIC
DELICATE
WOOL
ED
ON / O F F
XTRACAPACITY
U
JETSYSTEM 1000
E SA
S TAR T/PA U S E
RE SE
T
INSTRUCTION BOOKLET
GB
124970982.qxd
9/4/01
2:49 AM
Pagina
2
(Nero/Process Black pellicola)
Important Safety Information
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance and the relevant
warnings.
These warnings have been provided in the interest of safety. You MUST read them carefully
before installing or using the appliance.
Installation
Use
●
●
●
●
●
●
●
●
This appliance is heavy. Care should be taken when
moving it.
It is dangerous to alter the specifications or attempt
to modify this product in any way.
All packing and transit bolts must be removed before
use. Serious damage can occur to the product and to
property if this is not adhered to. See relevant section
in instructions.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Care must be taken to ensure that the appliance does
not stand on the electrical supply cable.
If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely.
●
●
●
●
●
Child Safety
●
●
●
●
●
●
This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
Pets and children have been known to climb into
washing machines. Please check your drum before
use.
The glass door becomes very hot during the washing
cycle. Keep children away from the vicinity of the
appliance whilst it is in operation.
Keep all packaging well away from children.
Keep all detergents in a safe place out of children’s
reach.
●
●
●
●
2
Always unplug the appliance and turn off the water
supply after use.
Do not overload the appliance. See relevant section
in the instruction book.
Only wash fabrics which are designed to be machine
washed. If in doubt, consult the care label on the
clothes.
Before washing, ensure that all pockets are empty
and buttons and zips are fastened. Avoid washing
frayed or torn articles and treat stains such as paint,
ink, rust, and grass before washing. Underwired bras
must NOT be machine washed.
Any objects such as coins, safety pins, nails, screws,
stones or any other hard, sharp material can cause
extensive damage and must not be placed into the
machine.
Garments which have been in contact with volatile
petroleum products should not be machine washed.
If volatile cleaning fluids are used, care should be
taken to ensure that the fluid is removed from the
garment before placing in the machine.
Wash small items such as socks, laces, washable
belts etc in a washing bag or pillow case as it is
possible for such items to slip down between the tub
and the inner drum.
Only use the advised quantities of fabric softener.
Damage to the fabric can ensue if you over-fill.
Refer to the manufacturer’s recommendations of
quantities.
As some duvets and eiderdowns should be washed
in large commercial machines because of their bulk,
please check with the manufacturer of the item
before washing in a domestic machine.
Leave the porthole door slightly ajar between washes
to preserve the door seal.
Under no circumstances should you attempt to repair
the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Zanussi Service
Force Centre. Always insist on genuine Zanussi
spare parts.
124970982.qxd
9/4/01
2:49 AM
Pagina
3
(Nero/Process Black pellicola)
Contents
For the User
Important Safety Information
Your New Washing Machine
Description of the Appliance
Door locked light
Detergent dispenser drawer
Child safety feature
The Control Panel
Operating sequence
Something Not Working
Service and Spare Parts
Guarantee Conditions
Zanussi Service Force
2
4
5
5
5
5
10-12
Load the laundry
10
Measure out the detergent
10
Measure out the fabric softener
10
Switch the machine on
10
Select the required programme/fabric
10
Select the temperature
11
Select the spin speed or the RINSE HOLD option
11
Select the desired options
11
Select the QUICK WASH option
11
Select the DELAY TIME
11
Start the programme
11
How to change a programme during its cycle
12
How to cancel a programme during its cycle
12
How to open the door during the cycle of
a programme
12
End of programme
12
Wash Care Symbols
Washing Programmes
Maintenance and Cleaning
Descaling
After each wash
External cleaning
Cleaning the dispenser drawer
Cleaning the drawer recess
Cleaning the filter
The dangers of freezing
Maintenance Wash
21
22-23
Installation Instructions
Technical Specifications
24
Unpacking
Positioning
Water inlet
Water drainage
Levelling
Special conditions
In the interest of the environment
Electrical connection
25
25
25
26
27
27
27
28
13-14
14
14
Which detergent?....
And in which form?
20
For the Installer
6-9
Washing Hints
19-20
15
16
17-18
17
17
17
17
17
17
18
18
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
3
24
124970982.qxd
9/4/01
2:49 AM
Pagina
4
(Nero/Process Black pellicola)
Your New Washing Machine
Your new washing machine, fitted with the Zanussi “JET SYSTEM”, meets all modern
requirements for effective treatment of laundry with low water, energy and detergent
consumption.
Even small loads are washed “economically” because the amount of water used is regulated
automatically according to the load and type of fabric.
●
●
●
Automatic cooling of the wash water to 60°C
before draining, with the 90°C programme. This
reduces thermal shock to fabrics, helping to prevent
creasing.
The special wool programme with its new delicate
wash system treats your woollens with extreme care.
The anti-unbalance device ensures that the washing
machine remains stable when spinning.
In the interest of the
environment
●
●
●
Ecological hints
To save water and energy and help protect the
environment, we recommend that you follow these
hints:
● Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
● The machine works more economically if it is fully
loaded.
● With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
● Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
●
Materials marked with the symbol
are
recyclable.
Check with your local Council or Environmental
Health Office to see if there are facilities in your area
for re-cycling this appliance.
When the appliance is to be scrapped, cut off the
power supply cable and make the door lock device
unusable to prevent young children from being
trapped inside.
Help to keep your country tidy - use authorised
disposal sites for your old appliance.
How do we help to protect the environment?
We use recycled paper!
Important
Your machine is fitted with a balance control device, which ensures the machine is stable during the spin.
If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly
distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the
wash load manually and select a spin programme. For more detailed information see the section headed “Something
Not Working”.
4
124970982.qxd
9/4/01
2:49 AM
Pagina
5
(Nero/Process Black pellicola)
Description of the Appliance
1
1 Detergent dispenser drawer
2 Control panel
3 Door locked light
4 Door opening handle
5 Filter
6 Adjustable feet
2
DELA
1200
900
700
500
IC
E
T
FA BR MP
ER A
T
SP
IN S P
FJS 1025 W
PREWASH
SUPER
RINSE
RINSE
HOLD
RE
HAND
E
OP
TIO N
S
SKIP
QUICK
TI M
V
E
90°
60°
50°
40°
30°
COTTONS
SYNTHETIC
DELICATE
WOOL
ED
ON / O F F
XTRACAPACITY
U
JETSYSTEM 1000
E SA
S TAR T/PA U S E
RE SE
T
3
4
5
6
Door locked light
It stays on during the whole programme indicating that
the door is locked.
When the light goes out, the door can be opened (see
page 12).
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
C0063
5
124970982.qxd
9/4/01
2:49 AM
Pagina
6
(Nero/Process Black pellicola)
The Control Panel
DELAY
1
2
3
ERA
4
T
SP
IN S P
E
OP
5
TI O N
6
S
SKIP
QUICK
TI
S TA R T / PA U S E
M E S AV
E
MP
SUPER
RINSE
RINSE
HOLD
RE
E
PREWASH
ED
FA B RI C
T
S
HAND
U
ON / OFF
1200
900
700
500
90°
60°
50°
40°
30°
COTTONS
SYNTHETIC
DELICATE
WOOL
FJS 122 5 W
7
8
9
RE SE
T
10 11 12
1 ON/OFF button
4 TEMPERATURE button
Press this button to switch the washing machine on.
The display (8) will show three blinking dashes or a
blinking zero. You will find more detailed explanations
on page 7 (see “DISPLAY”).
Press the ON/OFF button again to switch the machine
off.
Press this button repeatedly to increase or decrease the
temperature, if you want your laundry to be washed at a
temperature different from the one proposed by the
washing machine. The relevant light will light up.
Maximum temperatures are 90°C for cotton, 60°C for
synthetic fabrics, 40°C for delicate fabrics, wool and
fabrics to be hand-washed (HAND WASH
programme).
2 MAINS-ON light
This light is connected to the ON/OFF button. It lights
up when you press the button, and goes out when you
press it again.
Important!
By pressing the TEMPERATURE and SPIN SPEED
buttons simultaneously, the acoustic signal at the end of
the cycle is deactivated.
By pressing these 2 buttons again the acoustic signal is
reactivated.
3 FABRICS button
Press this button repeatedly to select the programme on
the basis of the type of laundry to be washed. The light
relevant to the selected programme will light up. The
washing machine will propose a temperature and
automatically select the maximum spin value provided
for the programme you have chosen. You can change
these values by operating buttons 4 and 5.
5 SPIN SPEED button
Press this button repeatedly to change the spin speed, if
you want your laundry to be spun at a speed different
from the one proposed by the washing machine. The
relevant light will light up.
Maximum speeds are:
• for cotton: 1,400, 1,200 or 1,000 rpm depending on
the model;
• for synthetic fabrics, wool, and fabrics to be handwashed: 900 rpm;
• for delicate fabrics: 700 rpm.
RINSE HOLD position : when you choose this
option, the machine will not drain the water of the last
rinse, so as not to wrinkle the laundry.
At the end of the cycle, the START/PAUSE button light
will flash, to indicate that the water must be drained.
To complete the cycle, choose one of the following
options:
Hand wash
When you select this programme, you obtain a
particularly delicate washing, suitable for articles of
clothing whose label indicates that they must be handwashed
.
6
124970982.qxd
9/4/01
2:49 AM
Pagina
7
(Nero/Process Black pellicola)
8 Display
• Draining and spin:
- Press the START/PAUSE button. The machine will
drain the water, then spin the laundry at the
maximum speed provided for the selected
programme.
- Select spin speed by means of button 5, and press
the START/PAUSE button.
• Drain only
- Press the SKIP/RESET button once, so as to cause
the DRAIN light
to light up, then press the
START/PAUSE button.
Important! If you accidentally press the SKIP/RESET
button more than once, the display will show three
blinking dashes. To cause the washing machine to
drain the water, select any washing programme by
means of the FABRIC button, then press
SKIP/RESET three times in order to select the
DRAIN position (only the DRAIN light will remain
lit).
The following pieces of information are shown on the
display:
• Three blinking dashes, when a programme is
cancelled by means of the SKIP/RESET button.
The three blinking dashes will also appear when you
press the ON/OFF button to switch the machine on, if
the previously selected cycle has been erased.
--• Duration of washing programme in hours
and minutes, after you have selected a programme.
6 OPTIONS button
Press this button to select the following options:
• PREWASH: select this option if you wish your
laundry to be prewashed before the main wash (not
available for wool and hand-wash cycle).
The prewash ends with a short spin at 650 rpm in
programmes for cotton and synthetic fabrics, whereas
in the programme for delicate fabrics the water is only
drained.
• SUPER RINSE: this option can be selected with all
programmes except the wool programme and hand
wash. The machine performs 4 rinses instead of 3.
This option is recommended for people who are
allergic to detergents, and in areas where the water is
very soft.
2.05
While the programme is running (after you have
pressed the START/PAUSE button), the displayed
time value decreases by one unit every minute.
• The washing machine has stopped with water in the
tub, at the end of a programme with the RINSE
HOLD option: this is indicated by a static zero.
• The washing machine has completed the
programme: this is indicated by a blinking zero. At
the same time, the door locked light goes out. The
zero will reappear when you switch the washing
machine on, unless the previous programme has been
erased by means of the SKIP RESET button.
7 TIME SAVE button
This button allows you to select the QUICK WASH
function, for laundry that is only slightly soiled (not for
wool and HAND WASH programme).
The washing time will be reduced according to the type
of fabric and the selected temperature.
0
7
124970982.qxd
9/4/01
2:49 AM
Pagina
8
(Nero/Process Black pellicola)
9 START/PAUSE button
Important!
The first time you use the washing machine, when
you switch it on, it may display a blinking zero and give
an audible warning signal. This is due to the fact that the
washing machine has performed a washing cycle during
the manufacturer’s inspection tests, and this cycle has
not been erased after its completion.
This button has three functions:
• Start: after you have selected the desired programme
and options, press this button to start the washing
machine. The light above the button will stop flashing
and remain lit.
If you have selected a delay time by means of button
11, the countdown will begin and will be shown on the
display.
• Delay start, a time value indicated in hours and
selected by means of the relevant button.
• Pause: when you press this button again, the
programme in progress is interrupted. The light above
the button will start flashing. To restart the programme,
press the button again.
When you PAUSE the cycle, the DOOR LOCKED
light goes out, and it becomes possible to open the
door, provided
• the washing machine is not in the heating phase
beyond 40°C;
• the level of the water is not high;
• the drum is not turning.
Important! You must set the washing machine to
PAUSE before you make any change in the programme
in progress.
• Draining of water and spinning after the execution of
programmes with the RINSE HOLD option.
The delay time is displayed for 3 seconds, then the
duration of the selected programme reappears.
After you have pressed the START/PAUSE button, the
countdown begins, and the delay time value decreases
by one unit every hour.
You can delay the start of the selected programme by
up to 24 hours in one hour intervals.
• An incorrect option selection has been made: this is
indicated by the message Err when a function
incompatible with the current programme is selected.
10 SKIP/RESET button
This button performs two functions:
- Clears the memory
- Selects special programmes
At the end of every programme the RESET button must
be pressed once or repeatedly to clear the programme
memory. This will be confirmed by three dashes,
flashing in the display.
If the previous programme is not cleared, the display
will show a “0” flashing and an audible signal will
sound, when you switch the machine on.
Selecting a special programme:
A wash programme must be selected in the normal way.
(START button not pressed)
The incorrect selection is also indicated by an audible
warning signal.
• An alarm code indicates a fault in the machine
operation (see the relevant chapter on page 19).
E20
S TA R T / P A U S E
8
124970982.qxd
9/4/01
2:49 AM
Pagina
9
(Nero/Process Black pellicola)
11 DELAY button
A normal wash cycle consists of the following phases,
Wash - Rinses - Spin and is confirmed by the
illumination of the corresponding LED,s.
This button makes it possible to delay the starting of the
programme by up to 24 hours. The delay you have
selected is shown on the display for about 3 seconds;
afterwards, the duration of the programme reappears.
You must select this option after you have set the
programme and before you press the START/PAUSE
button.
The time value shown on the display will decrease by
one unit every hour.
You can change the delay time at any moment, before
you press the START/PAUSE button.
If you have already pressed the START/PAUSE button,
and you wish to change or cancel the delay time,
proceed as follows:
PREWASH
WASH
RINSES
SPIN
DRAIN
To select rinse & spin, press the SKIP button once, the
wash LED goes out.
• set the washing machine to PAUSE by pressing the
START/PAUSE button;
• press the DELAY button until the display shows the
desired delay time or
• press the DELAY button once, to erase the delay time.
The display will indicate “0h”.
• press the START/PAUSE button again.
Important!
The door will be locked throughout the delay time
(DOOR LOCKED light lit).
If you need to open the door, you must first set the
washing machine to PAUSE by pressing the
START/PAUSE button. After you have closed the door,
press the START/PAUSE button again.
To select spin only, press the SKIP button twice.
The wash & rinse LED,s go out.
12 Programme phase indicator
lights
To select Drain, press the SKIP button three times, the
wash - rinse - spin LED,s go out.
When you select a programme, the lights relevant to the
phases that form the programme light up.
If you wish to cancel or advance the running programme
to the required phase, PAUSE the cycle and then press
the SKIP button as previously described.
After you have started the programme, only the light
relevant to the phase that is currently being carried out
will remain lit.
9
124970982.qxd
9/4/01
2:49 AM
Pagina
10
(Nero/Process Black pellicola)
Operating Sequence
4. Switch the machine on
Before the first wash, we recommend that you run a
cotton cycle at 60°C, without any laundry in the
machine, to remove any manufacturing residue from the
drum and tub.
Pour 1/2 a measure of detergent into the main wash
compartment of the dispenser drawer and start the
machine.
Press the ON/OFF button to switch the machine on. The
display will show three blinking dashes or a blinking
zero. The light above the button will light up.
O N / O FF
1.Load the laundry
0
---
Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
Close the door.
5. Select the desired programme/
fabric
Press the FABRICS button repeatedly, in order to select
the desired programme/fabric. The relevant light will
light up.
The lights relevant to the phases that form the
programme will light up.
The display will show the duration of the selected
programme, calculated on the basis of the maximum
load for each type of fabric. The START/PAUSE button
light will start flashing.
If the load of laundry to be washed is small, at the
beginning of the cycle the display will still indicate the
duration relevant to the maximum load. The duration
value will be gradually adjusted during the execution of
the cycle.
P0004
2.Measure out the detergent
Pull out the dispenser drawer until it stops. Measure out
the amount of detergent required and pour it into the
main wash compartment
.
If you wish to carry out the prewash, pour detergent into
the appropriate compartment marked
.
3.Measure out the fabric
softener
COTTONS
SYNTHETICS
DELICATES
WOOL
If required, pour fabric softener into the compartment
marked , without exceeding the «MAX» mark.
HAND
WASH
FA B RIC S
C0064
C0065
Close the drawer gently.
10
124970982.qxd
9/4/01
2:49 AM
Pagina
11
(Nero/Process Black pellicola)
6. Select the temperature
9. Select the QUICK WASH option
Press the TEMPERATURE button if you wish to select
a temperature value different from the one proposed by
the washing machine.
The relevant light will light up.
Depress TIME SAVE button to select the QUICK
WASH option, if your laundry is only slightly soiled.
The relevant light illuminates.
90°C
60°C
50°C
40°C
30°C
QUICK
T
RE
TI
EM
M E S AVE
P ER ATU
10. Select the DELAY TIME
Before you start the programme, if you wish the
starting to be delayed, press the DELAY button
repeatedly, or keep it pressed, to select the desired delay.
The selected delay time value (up to 24 hours) will
appear on the display for 3 seconds, then the duration of
the programme will appear again.
7. Select the spin speed or the
RINSE HOLD option
Press the SPIN SPEED button repeatedly, in order to
select the desired spin speed or the RINSE HOLD
option. The relevant light will light up.
If you select the RINSE HOLD option, the machine will
stop at the end of the programme with the water still in
the tub.
DELAY
1200
900
700
500
RINSE
HOLD
11. Start the programme
N SPEE
D
S
PI
Press the START/PAUSE button. The relevant light will
stop flashing, the DOOR LOCKED light will light up,
and only the light relevant to the phase that is in
progress will remain lit.
If you have chosen a delayed start, the washing machine
will begin the countdown.
The display will show the duration of the programme or
the selected delay.
8. Select the desired options
If your laundry is very dirty, it may be advisable to
select the PREWASH option.
If you wish the laundry to undergo an extra rinse, select
the SUPER RINSE option.
Press the OPTIONS button so as to cause one or both of
the lights to light up.
PREWASH
SUPER
RINSE
OP
S TA R T / P A U S E
TIO N S
11
124970982.qxd
9/4/01
2:49 AM
Pagina
12
(Nero/Process Black pellicola)
12. How to change a programme
during its cycle
After approximately 3 minutes, you can open the door.
Pay attention to the level and temperature of the
water in the washing machine!
When you close the door and press the ON/OFF button
again, the washing machine will resume the programme
from the point where it had been interrupted.
Before you make any change, you must pause the
washing machine by pressing the START/PAUSE
button.
It is possible to change any phase before the programme
carries it out.
Changing the type of fabric or temperature is possible,
obviously, only during the washing phase. When you
make a change in these two parameters, the washing
machine will resume the cycle from the beginning.
If it is necessary to drain the water in order to change the
programme in progress, proceed as follows:
• PAUSE the machine by pressing the START/PAUSE
button;
• press the SKIP/RESET button repeatedly, until only
the DRAIN light remains lit;
15. End of programme
At the end of the programme, the washing machine
stops automatically, gives an audible signal, and displays
a blinking zero.
If you had selected the RINSE HOLD option, the
START/PAUSE button light flashes to indicate that the
water must be drained. The display shows a steadily lit
zero.
When the programme has been completed, a blinking
zero appears on the display and the audible signal is
given.
The DOOR LOCKED light goes out at once.
Press the SKIP/RESET button repeatedly to erase
the programme that has just been carried out. If you
omit to do this, the next time you switch the washing
machine on, the blinking zero will appear on the
display and you will hear the audible signal.
• press the START/PAUSE button again.
When the water has been drained, the display shows a
blinking zero. You may now select a new programme
and press the START/PAUSE button to start it.
13. How to cancel a programme
during its cycle
Note: when you switch the machine on, if you must
erase the previously performed programme, it is also
sufficient to press the FABRIC button and select a new
programme.
Press the ON/OFF button to switch the machine off. The
relevant light will go out.
Remove the laundry from the washing machine.
Check whether the drum is completely empty, by
rotating it with your hand. The purpose of this is to
prevent any items of laundry from remaining
accidentally in the drum, where they might get damaged
in a subsequent wash (e.g. by shrinking) or bleed colour
into another load of laundry.
We advise you to close the water supply tap and
disconnect the plug from the socket.
Leave the door ajar in order to air the washing machine.
To cancel a programme that is being carried out, first
pause the washing machine by pressing the
START/PAUSE button, then press the SKIP/RESET
button repeatedly, until the display shows three blinking
dashes.
14. How to open the door during
the cycle of a programme
You can open the door, after having set the washing
machine to PAUSE, provided the following conditions
exist:
• the washing machine is not in the heating phase
beyond 40°C;
• the level of the water is not high;
• the drum is not turning.
If these requirements are met, when you pause the
washing machine, the DOOR LOCKED light goes out
and the door can be opened.
Should it not be possible to open the door, and should it
be absolutely necessary to do so, switch the machine off
by pressing the ON/OFF button.
12
124970982.qxd
9/4/01
2:49 AM
Pagina
13
(Nero/Process Black pellicola)
Washing Hints
Do NOT overload the machine. Weigh the laundry the
first few times you use the appliance.
●
The average weights of the most common items are
listed below as a guide:
●
1000g = 1 kg
Sheet
700-1000 g
Pillow case
100-200 g
Tablecloth
400-500 g
Serviette
50-100 g
Tea towel
70-120 g
Linen hand towel
100-150 g
Towelling hand towel
150-250 g
Towelling bath towel
700-1000 g
Bath robe
200-300 g
Apron
150-200 g
●
●
●
●
●
●
●
●
●
●
●
●
●
1000-1500 g
Man’s shirt
●
●
●
quantities.
Bleach is very corrosive; it should be used with care
and kept out of reach of children.
Some stains such as fruit, wine, grass, rust etc. are
difficult to remove and should be treated before
washing with specific products, which can be found
in most household shops. In some cases it may help
to soak the stain before washing with a special presoak product or biological detergent.
Only wool marked “Pure New Wool - washable,
preshrunk” can be washed in the machine using the
wool programme; other types of wool should be
washed by hand or dry cleaned.
If you have used the machine to wash, rinse or spin
only non-colour fast garments, there may be dye left
in the sump. To ensure any subsequent wash is not
contaminated with the dye, select and carry out a
rinse and spin programme, without any garments, to
ensure that any dye is removed from the sump.
Once you have finished using the machine, you are
advised to unplug it and turn off the water tap.
«JETSYSTEM» wash
Load the laundry loosely alternating large items with
small ones.
Sort the laundry according to the type of fabric,
colour-fastness and how dirty it is.
Avoid washing unhemmed or torn items as they may
unravel.
Before washing, empty all pockets of small objects
which may have been left inside (coins, keys, screws
etc). as these could damage the drain pump.
When washing curtains, remove the hooks.
Close poppers and zips and fasten loose buttons.
It is essential to wash new coloured items separately
when washing for the first time.
When washing fabrics requiring different wash
temperatures together, always select the lowest
temperature.
White items should not be washed with coloured
items.
Very small items (handkerchiefs, ribbons, socks etc)
should be washed in a washing bag or a pillow case.
Use a good quality detergent suitable for automatic
washing machines.
Use the correct quantities of detergent.
For wool, use gentle detergent only in small
As the Jetsystem is flexible and adjusts water intake
according to wash load size it is not possible to give you
exact recommandations as to the amount of detergent
that should be used for any one wash.
Therefore we recommend that you use approximately
1/3 less than the detergent manufacturer recommends on
the packet or bottle, making the appropriate allowances
for soft or hard water, and light or heavy soilage of
clothes. If you have judged the amount correctly you
should expect to see a soft sudsy liquid during the wash.
It is not necessary to have a head of lather on the water.
13
124970982.qxd
9/4/01
2:49 AM
Pagina
14
(Nero/Process Black pellicola)
Which detergent?....
And in which form?
To ensure you obtain the best wash results from your
appliance, it is important to use the right detergent in
your everyday wash, and only detergents recommended
for use in automatic machines.
To maintain the appearance of your clothes and
household textiles and to make them last longer you
should use different types of detergent for different
washes, whether for whites, colours or delicates.
Not only are there different types of detergent, but they
are also available in different forms. Whether you chose
a powder or liquid in traditional or compact form is
your own personal choice.
TRADITIONAL POWDERS
Pour the powder directly into the dispenser drawer. Do
not sprinkle powder onto clothes in the machine drum.
TRADITIONAL LIQUIDS
WHITES
Liquid can be placed in the main wash compartment of
the detergent drawer marked with the symbol , start
the machine immediately upon placing the detergent in
the dispenser drawer.
Alternatively the detergent is measured into the
specially designed dosing device* which should be
placed on top of the laundry, and at the back of the
machine drum.
We recommend the Ariel product
range which is biological and
designed to provide excellent
cleaning and stain removal even
at low temperatures.
NON BIOLOGICAL
If you prefer to use a non
biological detergent, which does
not contain enzymes we
recommend Fairy. Fairy provides
good cleaning and stain removal.
COMPACT POWDERS AND LIQUIDS
Compact detergents (or concentrates as they are also
known) are available in liquid or powder form, and
generally require a smaller dosage. Follow the
manufacturer’s instructions to ensure the most
economical usage. Pour the detergent directly into the
dispenser drawer, or alternatively measure the detergent
into the specially designed dosing device* which
should be placed on top of the laundry, and at the back
of the machine drum.
COLOUREDS
For coloured items you should use a
detergent which is designed to clean
while maintaining the original colour.
Ariel Color does not contain bleach
and therefore helps to preserve
colours.
* If you use a dosing device in a washer dryer,
please ensure the dosing device/ball is removed
before carrying out a drying programme.
DELICATE ITEMS
FABRIC CONDITIONERS
When washing delicates such as
woollens, you should use a product
which is specially designed to care for
fine fabrics.
Dreft Automatic is suitable for
woollens and other delicates.
These are ideal for improving ‘softness’, and also
reduce static cling on synthetics and make ironing
easier. They are available in two types:
For example Lenor liquid fabric
softener, for use in the washing
machine/washer dryer. The
liquid fabric softener should be
poured into the compartment
marked with the symbol .
Follow the manufacturer’s dosage
instructions and never exceed the
MAX level.
LAUNDRY BLEACH
For additional stain removal you may
wish to use a product such as Ace
Gentle Bleach which is used in addition
to your chosen detergent. Ace is
suitable for all washable fabrics
including silks, woollens and coloureds.
Bounce conditioning sheets for use
in a tumble dryer. We recommend
the conditioning sheets are pinned
(using a safety pin) to an article
of laundry and placed in the
tumble dryer.
14
124970982.qxd
9/4/01
2:49 AM
Pagina
15
(Nero/Process Black pellicola)
Wash Care Symbols
Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling
code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct
programme on your washing machine.
WASHING SYMBOL
WASH ACTION
95
Normal (Maximum)
White Cotton or Linen
without Special Finishes
60
Normal (Maximum)
Cotton, Linen or Viscose
without Special Finishes
Colourfast at 60°C.
50
Reduced (Medium)
Nylon, Polyester/Cotton, Viscose with
Special Finishes, Cotton/Acrylic Mix.
40
Normal (Maximum)
Cotton, Linen or Viscose
Colourfast at 40°C but not 60°C.
40
Reduced (Medium)
Acrylics, Acetate, Triacetate, Wool
mixes, Polyester/wool blends.
40
Much Reduced (Minimum)
Hand wash only
FABRIC
Wool, wool mixtures, Silks
Do not machine wash
BLEACHING
Chlorine bleach may be used
IRONING
Hot iron
Cotton, Linen, Viscose
Warm iron
Polyester mixtures, Wool
Cool iron
Acrylic, Nylon, Polyester
DRY CLEANING
May be dry cleaned. Other letters and/or a bar beneath the circle will
indicate the required process to the dry cleaner.
TUMBLE DRYING
with high heat setting
with low heat setting
May be tumble dried
X
A cross through any symbol means «DO NOT»
Important Notes
fabric conditioner to avoid the conditioner entering the
machine prematurely.
When using liquid detergent and a prewash programme,
place the detergent into the correct compartment in the
dispenser drawer, after the prewash has finished.
For best results, always use the dispenser drawer for
dispensing detergents and liquid additives.
Once the dispenser has been filled, close it by pushing it
in gently. This is particularly important if you are using
15
124970982.qxd
9/4/01
2:49 AM
Pagina
16
(Nero/Process Black pellicola)
Washing programmes
Type of
laundry and
symbols on
labels
60
95
White cotton:
e.g. sheets,
tablecloths,
household
linen
60
40
Load
5 kg
5 kg
30
Coloured
cotton: e.g.
shirts, blouses,
underwear,
towels, household linen
60
50
40
30
Synthetic
fabrics and
blends: e.g.
shirts, blouses,
underwear
40
30
30
Wool
Description of
programme
Consumption*
Available options
Energy
kWh
Water
litres
Time
h/min.
Main wash at
60°-90°C
3 rinses
Long spin
SPIN SPEED
RINSE HOLD
PREWASH
SUPER RINSE
QUICK
1.9
47
2.28
Main wash at
Cottons
60°-40°-30°C 60°-40°-30°C
3 rinses
Long spin
SPIN SPEED
RINSE HOLD
PREWASH
SUPER RINSE
QUICK
0.95
44
2.10
Cottons
60°-90°C
2.5 kg
Synthetics
60°-50°-40°30°C
Main wash at
60°-50°-40°30°C
3 rinses
Short spin
SPIN SPEED
RINSE HOLD
PREWASH
SUPER RINSE
QUICK
0.85
60
1.27
2.5 kg
Delicates
40°-30°C
Main wash at
40°-30°C
3 rinses
Short spin
SPIN SPEED
RINSE HOLD
PREWASH
SUPER RINSE
QUICK
0.55
53
1.04
2 kg
Wool
40°-30°C
Main wash at
40°-30°C
3 rinses
Short spin
SPIN SPEED
RINSE HOLD
0.35
52
53
2 kg
Hand wash
40°-30°C
Main wash at
40°-30°C
3 rinses
Short spin
SPIN SPEED
RINSE HOLD
0.2
60
55
Delicate fabrics: e.g.
acrylic fabrics,
viscose, polyester, synthetic
blends
40
Programme/
temperature
The “coloured cotton programme” at 60°C with a wash load of 5 kg is the reference programme for the data entered in
the energy label, in compliance with EEC 92/75 standards.
* This data is given purely as an indication: the consumption values may vary in relation to the quantity and type of
laundry, the temperature of the water supply and the ambient temperature. The data refers to the highest temperature
provided for each programme.
The machine is capable of washing up to 6 kg, however, to achieve optimum wash results it is recommended
that the above wash loads are adhered to.
16
124970982.qxd
9/4/01
2:49 AM
Pagina
17
(Nero/Process Black pellicola)
Maintenance and Cleaning
Cleaning the drawer recess
Before any maintenance or cleaning is carried out you
must DISCONNECT the appliance from the electricity
supply.
Having removed the drawer, use a small brush to clean
the recess, ensuring that all washing powder residue is
removed from the upper and lower part of the recess.
Replace the drawer and run the rinse programme
without any clothes in the drum.
Descaling
The water we use normally contains lime. It is a good
idea to periodically use a water softening powder in the
machine. Do this separately from any laundry washing,
and according to the softening powder manufacturer's
instructions. This will help to prevent the formation of
lime deposits.
After each wash
P0038
Leave the door open for a while. This helps to prevent
mould and stagnant smells forming inside the appliance.
Keeping the door open after a wash will also help to
preserve the door seal.
Cleaning the filter
The water drain filter
A clean filter is important for the correct operating of the
machine, and should therefore be cleaned after every
washing programme.
Open the filter door and place a container underneath to
catch any spillage. If the filter is blocked and the
machine is unable to drain you will need to drain the
water manually from the machine at this stage. To do
this, unhook the drain hose from the standpipe or sink
and hold the end of the hose over a bowl on the floor.
The water should drain by gravity into the bowl. When
the bowl is full, hook the hose back up and empty the
bowl. Repeat the procedure until water stops flowing
out.
External cleaning
Clean the exterior cabinet of the appliance with soap and
water only, and then dry thoroughly.
Cleaning the dispenser drawer
The washing powder and additive dispenser drawer
should be cleaned regularly.
Remove the drawer by pressing the catch downwards
and by pulling it out. Flush it out under a tap, to remove
any traces of accumulated powder.
To aid cleaning, the top part of the additive compartment
should be removed.
P0861
C0066
C0067
C0068
P1086
17
P0860
124970982.qxd
9/4/01
2:49 AM
Pagina
18
(Nero/Process Black pellicola)
The dangers of freezing
Unscrew and remove the filter.
Clean carefully under a fast running tap.
If the machine is exposed to temperatures below 0°C,
certain precautions should be taken.
● Turn off the water tap.
● Unscrew the inlet hose.
● Unhook the drain hose from the rear support and
position the end of this hose and that of the inlet
hoses in a bowl. Run the draining programme.
To do this:
● Switch the machine on
● Select a washing programme
● Press the SKIP/RESET button three times
● Press START/PAUSE button
● Disconnect the appliance.
● Screw the inlet hose and reposition the drain hose.
● When you intend to start the machine up again, make
sure that the room temperature is above 0°C.
P0040
P0859
Warning
When the appliance is in use and depending on the
programme selected there can be hot water in the filter.
Never remove the filter during a wash cycle, always
wait until the appliance has finished the cycle, and is
empty. When replacing the filter, ensure it is securely
retightened so as to stop leaks and young children being
able to remove it.
The water inlet filter
If your water is very hard or contains traces of lime
deposit, the water inlet filter may become clogged.
It is therefore a good idea to clean it from time to time.
Turn off the water tap. Unscrew the water inlet hose.
Clean the filter using a hard bristle brush.
Tighten up the inlet hose.
Maintenance Wash
With the use of low temperature washes it is possible to
get a build up of residues inside the drum.
We recommend that a maintenance wash be performed
on a regular basis.
To run a maintenance wash:
● The drum should be empty of laundry.
● Select the hottest cotton wash programme.
● Use a normal measure of detergent, must be a
powder (such as Ariel Futur).
P1090
18
124970982.qxd
9/4/01
2:49 AM
Pagina
19
(Nero/Process Black pellicola)
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without
calling out an engineer. Before contacting your local Service Force Centre, please carry out the checks listed
below.
IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
During machine operation it is possible that one of the following alarm codes appears on the display:
- E10 : problem with the water supply
If at the end of the programme the alarm code EF0 is displayed
- E20 : problem with water draining
this means that the drain filter is clogged.
- E40 : door open
Once the problem has been eliminated, press the START/PAUSE button
to restart the programme. If after all
checks, the problem persists, contact your local Service Force Centre.
Symptom
Possible causes
The machine does not start
●
●
●
●
●
●
The machine does not fill
●
●
●
●
The machine fills then empties
immediately
●
●
●
The machine does not empty and/or
does not spin
●
●
●
●
●
●
There is water on the floor
●
●
●
●
●
Unsatisfactory washing results
●
●
●
●
The door has not been closed. (E40)
The plug is not properly inserted in the power socket.
There is no supply at the socket.
The main fuse or the fuse in the plug has blown.
The START/PAUSE button has not been depressed.
The DELAY START option has been selected.
The water tap is closed. (E10)
The filter in the inlet hose is blocked. (E10)
The inlet hose may be squashed or kinked. (E10)
The door has not been closed. (E40)
The end of the drain hose is too low.
The end of the drain hose is submerged in water.
There is no vent in the end of the drain hose.
The drain hose may be squashed or kinked. (E20)
The RINSE HOLD option has been selected.
The drain filter may be blocked. (E20)
The drain hose extension, if fitted, is not correct. Follow the
instructions for connecting to the waste.
The drainage system pipes are blocked. (E20)
The wash load is unbalanced: redistribute the clothes inside the drum to
allow the machine to spin.
Too much detergent or unsuitable detergent has been used (creates too
much foam).
Check whether there are any leaks from the inlet hose fittings. It is not
always easy to see this as the water runs down the hose; check to see if
it is damp.
The drain hose may be damaged or not securely positioned.
The detergent dispenser drawer or recess is clogged.
The drainage system pipes are blocked.
Too little detergent or unsuitable detergent has been used. An
insufficient amount of detergent leaves the laundry looking grey and
causes lime scale to form.
Stubborn stains have not been treated prior to washing
The correct wash programme/temperature has not been selected.
Too much laundry has been placed in the drum.
19
124970982.qxd
9/4/01
2:49 AM
Pagina
20
(Nero/Process Black pellicola)
Symptom
Possible causes
The machine vibrates when spinning
●
●
●
●
●
The door will not open
The internal packing has not been removed.
The machine is in contact with the wall or furniture.
The machine is not level and stable (check diagonally).
The washing load is badly distributed in the drum.
Maybe there is very little laundry in the drum.
●
The water level is above the bottom edge of the door.
The machine is heating the water.
● The drum is turning.
The door can only be opened when the relevant light has gone out.
●
Spinning starts late or the machine
does not spin
●
The machine makes an unusual
noise
●
No water is visible in the drum
●
The electronic unbalance detection device has cut in because the laundry
is not evenly distributed in the drum. The laundry is redistributed by
reverse rotation of the drum. This may happen several times before the
unbalance disappears and normal spinning can resume. If, after 15
minutes, the laundry is still not evenly distributed in the drum, the
machine will not spin. In this case, redistribute the load manually and
select the spin programme.
The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor ensures
a softer start and more even distribution of the laundry in the drum
when spinning, as well as increased stability of the machine.
Machines based on modern technology operate very economically
using very little water without affecting performance.
Service & Spare Parts
Customer Care
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Zanussi Service Force Centre by telephoning:
For general enquiries concerning your Zanussi appliance
or for further information on Zanussi products, please
contact our Customer Care Department by letter or
telephone as follows:
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
The addresses are listed on the following pages.
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working”.
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of fault
4. The model and serial number of the appliance (found
on the rating plate - see picture).
5. The purchase date
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel 08705 727727*
or visit our website at www.zanussi.co.uk
* calls to this number may be recorded for training
purposes.
Mod. ..........
Prod. No. ...........
Ser. No. .........
Mod. ..........
Prod. No. ...........
P0042
Ser. No. .........
20
124970982.qxd
9/4/01
2:49 AM
Pagina
21
(Nero/Process Black pellicola)
Guarantee Conditions
Standard guarantee conditions
Exclusions
We, Zanussi undertake that if, within 12 months of the
date of the purchase, this Zanussi appliance or any part
thereof is proved to be defective by reason only of
faulty workmanship or materials, we will, at our option,
repair or replace the same FREE OF ANY CHARGE
for labour, materials or carriage on condition that:
● The appliance has been correctly installed and used
only on the electricity supply stated on the rating
plate.
● The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer’s instructions.
● The appliance has not been serviced, maintained,
repaired, taken apart or tampered with, by any
person not authorised by us.
All service work under this guarantee must be
undertaken by a Zanussi Service Force Centre.
Any appliance or defective part replaced shall become
the Company’s property.
This guarantee is in addition to your statutory and other
legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
This guarantee does not cover:
●
●
●
●
Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliances
outside the United Kingdom.
Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are NOT
marketed by Zanussi.
European guarantee
If you should move to another country within Europe
then your guarantee moves with you to your new home
subject to the following qualifications:
● The guarantee starts from the date you first
purchased your product.
● The guarantee is for the same period and to the same
extent for labour and parts as exists in the new
country of use for this brand or range of products.
● The guarantee relates to you and cannot be
transferred to another user.
● Your new home is within the European Community
(EC) or European Free Trade Area.
● The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household.
● The product is installed taking into account
regulations in your new country.
Before you move please contact your nearest Customer
Care Centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look
after you and your appliances.
France
Senlis
+33 (0)344 62 22 22
Germany
Nurnberg
+49 (0)911 323 2600
Italy
Pordenone
+39 (0)1678 47053
Sweden
Stockholm
+46 (0)8 738 79 50
UK
Slough
+44 (0)1753 219897
21
124970982.qxd
9/4/01
2:49 AM
Pagina
22
(Nero/Process Black pellicola)
To contact your local Service Force Centre telephone 08705
CHANNEL ISLANDS
Guernsey Electricity
PO Box 4
Vale, Guernsey
Channel Islands GY1 3AD
GUERNSEY
Jersey Electricity Company
Haut De L’orme
Rue De Haut De L’orme
Trinity
Jersey
Channel Islands JE3 5FG
JERSEY
SCOTLAND
ABERDEEN
AUCHTERMUCHTY
BLANTYRE
DUMFRIES
DUNOON
EDINBURGH
GLASGOW
INVERNESS
ISLE OF ARRAN
ISLE OF BARRA
ISLES OF BUTE
54 Claremont Street
Aberdeen AB10 6RA
33a Burnside
Auchtermuchty
Fife KY14 7AJ
Unit 5
Block 2
Auchenraith Ind. Estate
Rosendale Way
Blantyre G72 0NJ
93 Irish Street
Dumfries
DG1 2 PQ
7 Hill Street
Dunoon
Argyll
PA23 7AL
Unit 12
Dumbryden Ind. Estate
2 Dumbryden Road
Edinburgh
EH14 2AB
Unit 4
Wellington Road
Bishopriggs
Glasgow G64 2SA
Unit 3BI
Smithton Ind. Estate
Smithton
Inverness IV2 7WL
ISLE OF LEWIS
2, 6 & 8 Woodmarket
Kelso
Borders
TD5 7AX
KELSO
7 King Street
Kirkwall
Orkney
KW15 1JF
ORKNEY
PERTH
(OWN SALES)
SHETLAND
(OWN SALES)
SHETLAND
(OWN SALES)
WHALSAY
(OWN SALES)
Walker Engineering
Glenmhor
Upper Serpentine Road
Rothesay
Isle of Bute PA20 9EH
Scottish Hydro Electric
Central Warehouse
Inveralmond
Perth PH1 3AF
3-4 Carlton Place
Lerwick
Shetland
ZE1 0PW
Bolts Shetland
26 North Road
Lerwick
Shetland ZE1 0PE
BELFAST
Owenmore House
Kilwee Business Park
Dunmurry
Belfast
BT17 0HD
WALES
CARDIFF
CLYWD
DYFED
OSWESTRY
NORTH EAST
Unit 4
Guardian Industrial Estate
Clydesmuir Road
Cardiff
CF2 2QS
Unit 6-7 Coed Parc
Abergele Road
Rhuddlan
Clwyd
LL18 5UG
Unit 9
St. Clears Business Park
Tenby Road
St. Clears
Carmarthen
SA33 4JW
Plas Ffynnon Warehouse
Middleton Road
Oswestry
SY11 2PP
22
Unit 356a
Dukesway Court
Dukesway
Gateshead NE11 0BH
GATESHEAD
15 Hainton Avenue
Grimsby
N. E. Lincs
DN32 9AS
GRIMSBY
Unit 1
Boulevard Industrial Estate
Hull
HU3 4AY
HULL
64-66 Cross Gates Road
Cross Gates
Leeds
LS15 7YS
LEEDS
NEWTON AYCLIFFE
SHEFFIELD
Leask Electrical
Harisdale
Symbister, Whalsay
Shetland ZE2 9AA
NORTHERN IRELAND
R Haggerty
Bruach
Blackwaterfoot
Isle of Arran
J Zerfah
244 Bruernish
Isle of Barra
Western Islands HS9 5QY
ND Macleod
16 James Street
Stornoway
Isle of Lewis PA87 2QW
929 929
Unit 23
Northfield Way
Aycliffe Industrial Park
Newton Aycliffe
DL5 6EJ
Pennine House
Roman Ridge Road
Sheffield
S9 1GB
NORTH WEST
BIRKENHEAD
CARLISLE
ISLE OF MAN
BOLTON
PRESTON
STOCKPORT
1 Kelvin Park
Dock Road
Birkenhead
CH41 1LT
Unit 7
James Street Workshops
James Street
Carlisle
Cumbria CA2 5AH
South Quay Ind. Estate
Douglas
Isle of Man
IM1 5AT
Unit B
Central Industrial Estate
St Marks Street
Bolton
BL3 6NR
Unit 250
Dawson Place
Bamber Bridge
Preston
Lancashire PR5 8AL
Unit 20 Haigh Park
Haigh Avenue
Stockport
SK4 1QR
124970982.qxd
9/4/01
2:49 AM
Pagina
23
(Nero/Process Black pellicola)
To contact your local Service Force Centre telephone 08705
LONDON & EAST ANGLIA
MIDLANDS
BIRMINGHAM
66 Birch Road East
Wyrley Trading Estate
Witton
Birmingham
B6 7DB
BOURNE
Pinfold Road
Bourne
PE10 9HT
BRIDGNORTH
68 St. Mary’s Street
Bridgnorth
Shropshire
WV16 4DR
GLOUCESTER
HEREFORD
101 Rycroft Street
Gloucester
GL1 4NB
Units 3 & 4
Bank Buildings
Cattle market
Hareford
HE4 9HX
ILKESTON
Unit 2
Furnace Road
Ilkeston DE7 5EP
LEICESTER
Unit 7
Oaks Industrial Estate
Coventry Road
Narborough
Leicestershire
LE9 5GF
11a Gardner Ind. Estate
Kent House Lane
Beckenham
Kent BR3 1QZ
ASHFORD
CHELMSFORD
Hanbury Road
Widford Ind. Estate
Chelmsford
Essex
CM12 3AE
Unit 2
Bridge Road Business Centre
Bridge Road
Ashford
Kent TN23 1BB
FLEET
Unit 1
Redfields Ind. Estate
Church Crookham
Fleet
Hampshire GU13 0RD
HAYWARDS
HEATH
21-25 Bridge Road
Haywards Heath
Sussex RH16 1UA
TONBRIDGE
Unit 30
Deacon Trading Estate
Morley Road
Tonbridge
TN9 1RA
COLINDALE
ELTHAM
ENFIELD
284 Alma Road
Enfield
London
EN3 7BB
GRAVESEND
Unit B4
Imperial Business Estate
West Mill
Gravesend
Kent
DA11 0DL
BARNSTAPLE
Unit 6C
Elton Park Business Centre
Hadleigh Road
Ipswich
IP2 0DD
BOURNEMOUTH 63-65 Curzon Road
IPSWICH
SOUTH WEST
Main Road
Fremington
Barnstaple
North Devon EX31 2NT
Bournemouth
Dorset
BH1 4PW
LONDON
2 - 4 Royal Lane
Yiewsley
West Drayton
Middlesex
UB7 8DL
MAIDENHEAD
Reform Road
Maidenhead
Berkshire
SL6 8BY
MOLESEY
Unit 3
Sterling Park
Claymore
Tamworth
B77 5DQ
10 Island Farm Avenue
West Molesey
Surrey
KT8 2UZ
NEWBURY
NEWTON ABBOT Unit 2
Units 1 & 2
Northbrooks Close
Gregorys Mill Ind. Estate
Worcester
WR3 8BP
9 Pipers Court
Berkshire Drive
Thatcham
Berkshire
RG19 4ER
NORWICH
2b Trafalgar Street
Norwich
NR1 3HN
REDRUTH
SUNBURY
Unit 1a
The Summit
Hanworth Road
Sunbury on Thames
TW16 5DB
NEWCASTLE
UNDER LYME
18-21 Croft Road
Brampton Ind. Estate
Newcastle under Lyme
Staffordshire
ST5 0TW
WORCESTER
194 Court Road
Mottingham
Eltham
London SE9 4EW
16-17 Woodside Ind. Park
Works Road
Letchworth
Herts
SG6 1LA
Unit 8
Clifton Street
Stone Field Park
Lincoln
LN5 8LQ
TAMWORTH
Unit 14
Capitol Park
Capitol Way
Colindale
London NW9 0EQ
LETCHWORTH
LINCOLN
REDDITCH
SOUTH EAST
BECKENHAM
HIGHAM FERRERS 30 High Street
Higham Ferrers
Northants
NN10 8PL
929 929
13 Thornhill Road
North Moons Moat
Redditch
Worcestershire
B98 9ND
23
BRIDGEWATER
6 Herswell Business Park
Salmon Parade
Bridgwater
Somerset TA6 5PY
BRISTOL
11 Eldon Way
Eldonwall Trading Estate
Bristol
BS4 3QQ
EMSWORTH
266 Main Road
Southbourne
Emsworth
PO10 8JL
ISLE OF WIGHT
Unit 8
Enterprise Court
Ryde Business Park
Ryde
Isle of Wight PO33 1DB
Zealley Ind. Estate
Kingsteignton
Newton Abbot
TQ12 3TD
Unit 7D
Pool Ind. Estate
Druids Road
Redruth
Cornwall TR15 3RH
124970982.qxd
9/4/01
2:49 AM
Pagina
24
(Nero/Process Black pellicola)
Installation Instructions
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.
Should the appliance power supply cable need to
be replaced, this should be carried out by our
Service Force Centre.
Technical Specifications
DIMENSIONS
Height
Width
Depth
POWER SUPPLY VOLTAGE
TOTAL POWER ABSORBED
85 cm
60 cm
60 cm
230-240 V/50 Hz
2050 W (10A)
WATER PRESSURE
Minimum
Maximum
50 kPa (0.5 bar)
800 kPa (8 bar)
RECOMMENDED LOAD
Cotton, linen
Synthetics
Delicate fabrics
Wool/Hand Wash
5 kg (max. 6 kg)
2.5 kg
2.5 kg
2 kg
SPIN SPEED
Maximum
CONSUMPTION DATA FOR WASHING
5 KG NORMALLY SOILED COTTON
ITEMS AT 60°C
Energy
Water
1000 rpm (FJS 1025 W)
1200 rpm (FJS 1225 W)
1400 rpm (FJS 1425 W)
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
24
0.95 kWh
44 litres
124970982.qxd
9/4/01
2:49 AM
Pagina
25
(Nero/Process Black pellicola)
Unpacking
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is not
impeded by carpets, rugs etc. Check that the machine
does not touch the wall or other kitchen units.
Never place cardboard, wood or similar materials under
the machine to compensate for any unevenness in the
floor.
Your new washing machine has been designed to be
permanently plumbed in to your home’s water supply
and drainage system. However, if this is not possible, it
may be connected to a suitable existing tap with the
drain hose discharging into a sink.
The appliance has an inlet hose, with female 3/4” BSP
thread connector. If this connection is not compatible
with the plumbing of the existing installation, a variety
of connectors are available from good hardware stores
and plumbers merchants to suit most domestic
plumbing. Any alteration to your existing plumbing
must be carried out by a competent person, or qualified
plumber.
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all the packaging for re-use in
case the machine is to be transported again.
Using a spanner unscrew and remove the rear right bolt.
Lay the machine gently on its back, making sure that the
hoses are not squashed.
P0255
Remove the polystyrene block from the bottom of the
machine and release the two plastic bags.
Carefully slide out the right polythene bag (1).
Repeat the operation for the left polythene bag (2).
2
P1068
Installation on a Suspended Floor
Suspended wooden floors are particularly susceptible to
vibration. To help prevent vibration we recommend you
place a waterproof wood panel, at least 15 mm thick
under the appliance, secured to at least 2 floor beams
with screws. If possible install the appliance in one of
the corners of the room, where the floor is more stable.
1
P1066
Water inlet
Remove the polystyrene base.
Set the machine upright and remove the two remaining
bolts from the back.
Pull out the three plastic spacers from the holes into
which the bolts were fitted.
Plug all the holes with the plugs which you can find in
the envelope containing the instruction booklet.
Connect the hose to a tap with a 3/4” thread.
P1088
P0255
Installation should comply with local water authority
and building regulations’ requirements.
The appliance must be connected to a cold water
supply.
A minimum water pressure of 50 kPa (0.5 bar) is
required for safe operation of the appliance.
P0020
25
124970982.qxd
9/4/01
2:49 AM
Pagina
26
(Nero/Process Black pellicola)
If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system.
There should be a minimum distance of 5.02m
(161/2 ft) between the appliance’s inlet and the bottom
of the water storage tank.
Set the hose correctly by loosening the ring nut. After
positioning the inlet hose, be sure to tighten the ring nut
again to prevent leaks.
When discharging into a standpipe ensure that the top of
the curve in the hose end is no more than 90cm (35.4'')
and no less than 60cm (23.6'') above floor level. The
upright standpipe should have a minimum length of
30cm (12'') from the bottom of the elbow to the top of
the pipe (see diagram).
Make sure that it is designed in such a way, that the end
of the drain hose cannot be covered with water. The
drain hose may be extended to a maximum of 4 metres.
An additional drain hose and joining piece
is available from your local Service Force Centre.
The joining piece must have an internal diameter of
18mm.
If you intend the drain hose to empty into a sink, make
sure that the sink is empty and the plug hole is not
blocked. Use the plastic “U-Piece” supplied.
P0021
Water drainage
This appliance is designed to be permanently plumbed
into your home's water supply and drainage system.
P0022
Important
Before connecting up the machine to new pipework or
to pipework that has not been used for some time, run
off a reasonable amount of water to flush out any debris
that may have collected in the pipes.
Min.60 cm.
(23.6")
Max. 90 cm.(35.4")
3 pin
P1039
Min. 30 cm.(12")
The appliance drain hose should hook into a standpipe,
the hook in the drain hose is formed using the plastic
“U-Piece” supplied.
The standpipe should have an internal diameter of
approximately 38mm (see diagram) thus ensuring there
is an air break between the drain hose and standpipe.
38 mm.(1/1 2") diameter
standpipe
P1040
26
124970982.qxd
9/4/01
2:49 AM
Pagina
27
(Nero/Process Black pellicola)
Levelling
In the interest of the
environment
Level the washing machine by raising or lowering the
feet. The feet may be tight to adjust as they incorporate
a self locking nut, but the machine MUST be level and
stable (check diagonally).
Washing machines and dishwashers should be
connected to the FOUL drainage system, the water will
then be taken to a sewage works for treatment before
being discharged safely into a river.
It is essential that these appliances are not connected to
the surface water drainage system as this water is
discharged directly into a river or stream and may cause
pollution.
If you require any further advice please contact your
local authority drainage department.
P1051
Any necessary adjustment can be made with a spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
Some vibration is inevitable, especially if mounted on a
wooden floor.
Sprung wooden floors are particularly susceptible to
vibration. For advice, consult a builder. If possible,
always place the machine on a solid floor.
SHOWER
SINK
TOILET
BATH
BIDET
Special conditions
If the floor is carpeted or covered with crumbly or soft
material, insert a rigid support base under the feet to
prevent noise, vibration or displacement. The base
should protrude a few centimetres beyond the edges of
the machine.
WASHING
MACHINE
DISHWASHER
RAINWATER
'RUN-OFF'
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
Warning
The machine should NOT be placed on deep pile
carpeting.
UNTREATED
DISCHARGE
FOUL SEWERS
SEWAGE
TREATMENT
WORKS
TREATED
DISCHARGE
RIVER
P0987
Note
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
27
RIVER
124970982.qxd
9/4/01
2:49 AM
Pagina
28
(Nero/Process Black pellicola)
Electrical connection
The wire coloured brown must be connected to the
terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
WARNING:
A cut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate. The rating plate is located at the top of the
rim of the open door.
Should the appliance power supply cable neeed to be
replaced, this should be carried out by our Service
Force Centre.
Mod. ..........
Prod. No. ...........
Ser. No. .........
Note
When the appliance is installed the power supply cable
must be accessible.
Permanent connection
Mod. ..........
Prod. No. ...........
Ser. No. .........
P0042
In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap
of 3mm between the switch contacts and of a type
suitable for the required load in compliance with the
current electrical regulations.
The switch must not break the yellow and green earth
cable at any point.
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS1363A) fuse
must be used.
Should the plug need to be replaced for any reason,
proceed as described below.
The wires in the mains lead are coloured in accordance
with the following code:
Green and Yellow
- Earth
Blue
- Neutral
Brown
- Live
GREEN & YELLOW
13 A
E
N
L
BROWN
BLUE
P1041
CORD CLAMP
The wire coloured green and yellow must be connected
to the terminal marked with the letter «E» or by the
earth symbol
or coloured green and yellow.
The wire coloured blue must be connected to the
terminal marked «N» or coloured black.
28
124970982.qxd
9/4/01
2:49 AM
Pagina
30
(Nero/Process Black pellicola)
From the Electrolux Group. The world’s No. 1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use.
More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners,
chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries
around the world.
© Electrolux Household Appliances Limited 2000
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising