Electrolux | EWF934 | User manual | Electrolux EWF934 User Manual

Electrolux EWF934 User Manual
Copertina 132990672•GR.qxd
23-03-2004
12:41
Pagina 1
PLUNTHRIO ROUCWN
ODHGIES GIA THN EGKATASTASH
KAI TH CRHSH
132990671 GB.qxd
27/02/2004
10:11
Pagina
2
Dear customer,
Please read these operating instructions carefully
and pay particular attention to the safety notes
indicated in the first pages. We recommend that you
keep this instruction booklet for future reference and
pass it on to any future owners.
Transport damages
When unpacking the appliance, check that it is not
damaged. If in doubt, do not use it and contact the
Service Centre.
The symbols you will see on some paragraphs of this booklet have the following meaning:
The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly
important for your safety or correct functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use of
the appliance.
Tips and information about economical and ecological use of the machine are marked with this symbol.
Our contribution to the protection of the
environment: we use recycled paper.
2
132990671 GB.qxd
27/02/2004
10:11
Pagina
3
Warnings
Disposal
Maintenance
4-5
5
Tips for environmental protection 5
23-24
Bodywork
23
Door seal
23
Detergent dispenser drawer
23
Drain pump
23
Technical specifications
6
Water inlet filter
23
Emergency emptying out
24
Installation
7
Frost precautions
24
Unpacking
7
Positioning
7
Water inlet
7-8
Water drainage
8
Electrical connection
8
Your new washing machine
9
Description of the appliance
9
Detergent dispenser drawer
Use
Control panel
Controls
Washing hints
Sorting the laundry
9
10
10
10-13
14-15
14
Temperatures
14
Before loading the laundry
14
Maximum loads
14
Laundry weights
14
Removing stains
14
Detergents and additives
15
International wash code symbols
Something not working?
16
Operating sequence
17-19
Washing programmes
20-22
3
25-26
ENGLISH
Contents
132990671 GB.qxd
27/02/2004
10:11
Pagina
4
Warnings
The following warnings are provided in the interests of overall safety. You must read them carefully before
installing or using the appliance.
• Leave the porthole door slightly ajar when the
appliance is not in use. This preserves the door
seal and prevents the formation of musty smells.
Installation
• All internal packing must be removed before using
the appliance. Serious damage may be caused to
the machine or adjacent furniture if the protective
transit devices are not removed or are not
completely removed. Refer to the relevant
paragraph in the instruction book.
• Always check that water has emptied out before
opening the door. If not, drain the water following
the instructions in the instruction book.
• Always unplug the appliance and shut the water
tap after use.
• Any electrical work required to install this appliance
must be carried out by a qualified electrician.
• Any plumbing work required to install this
appliance must be carried out by a qualified
plumber.
General safety
• Repairs to the machine must be carried out only by
qualified personnel. Repairs carried out by
inexperienced persons could cause serious
danger. Contact your local Service Centre.
• After having installed the machine, check that it is
not standing on its electrical supply cable.
• If the appliance is placed on a carpeted floor,
ensure that air can circulate freely between the
feet and the floor.
• Never pull the power supply cable to remove the
plug from the socket; always take hold of the plug
itself.
• During high temperature wash programmes the
door glass may get hot. Do not touch it!
Use
• This appliance is designed for domestic use. It
must not be used for purposes other than those for
which it was designed.
• Only wash fabrics which are designed to be
machine washed. Follow the instructions on each
garment label.
• Do not overload the appliance. Follow the
instructions in the instruction book.
• Make sure that all pockets are empty. Objects such
as coins, safety pins, pins and screws can cause
extensive damage.
• Do not machine wash garments saturated with
petroleum, methylated spirits, trichlorethylene, etc.
If such fluids have been used to remove stains
prior to washing, wait until they have completely
evaporated from the fabric before placing
garments in the appliance.
• Place small items such as socks, belts, etc. in a
cloth bag or pillowcase to prevent them getting
trapped between the drum and the tub.
• Use only the recommended quantities of fabric
softener. An excessive amount could damage the
laundry.
4
27/02/2004
10:11
Pagina
5
To disable this device and restore the possibility of
closing the door, rotate the button anti-clockwise
until the groove is vertical.
Child safety
• Children are often not aware of how dangerous
electrical appliances can be. When the machine is
working, children should be carefully supervised
and not be allowed to play with the appliance.
• The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children - danger
of suffocation! Keep them out of children’s reach.
• Keep all detergents in a safe place out of children’s
reach.
P1131
• Make sure that children or pets do not climb into
the drum. To avoid this the machine incorporates a
special feature. To activate this device, rotate the
button (without pressing it) inside the door
clockwise until the groove is horizontal. If
necessary use a coin.
• When the appliance is to be scrapped, cut off the
electrical supply cable and destroy the plug with
the remaining cable. Disable the door catch in
order to prevent children from becoming trapped
inside while playing.
Disposal
Packaging materials
The materials marked with the symbol
recyclable.
Machine
are
Use authorised disposal sites for your old appliance.
Help to keep your country tidy!
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
Tips for environmental protection
To save water, energy and to help protect the
environment, we recommend that you follow these
tips:
• With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
• Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
• Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
• The machine works more economically if it is fully
loaded.
5
ENGLISH
132990671 GB.qxd
132990671 GB.qxd
27/02/2004
10:11
Pagina
6
Technical specifications
DIMENSIONS
Height
Width
Depth
85 cm
60 cm
59 cm
MAXIMUM LOAD
Cotton
Synthetics
Delicates
Woollens and handwash
Silk
5 kg
2,5 kg
2.5 kg
2 kg
1 kg
SPIN SPEED
700 rpm max. (EWF 734)
900 rpm max. (EWF 934)
1000 rpm max. (EWF 1034)
POWER SUPPLY VOLTAGE/FREQUENCY
TOTAL POWER ABSORBED
MINIMUM FUSE PROTECTION
220-230 V/50 Hz
2200 W
10 A
WATER PRESSURE
050 kPa
800 kPa
Minimum
Maximum
This appliance complies with the following EEC Directives:
73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility.
6
132990671 GB.qxd
27/02/2004
10:11
Pagina
7
7. Plug all the holes with the plugs which you will
find in the envelope containing the instruction
booklet.
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
1. Using a spanner, unscrew and remove the two
rear bottom screws. Slide out the two plastic pins.
P1128
P0002
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that the
machine does not touch the wall or other kitchen
units.
Carefully level by screwing the adjustable feet in or
out. Never place cardboard, wood or similar
materials under the machine to compensate for any
unevenness in the floor.
P0001
P1129
2. Lay the machine on its back, taking care not to
squash the hoses. This can be avoided by
placing one of the corner packing pieces between
the machine and the floor.
3. Remove the polystyrene block from the bottom of
the machine and release the two plastic bags.
1
2
3
P1051
P1124
Water inlet
4. Very carefully slide out the left polythene bag,
removing it towards the right and then
downwards.
Connect the water inlet hose to a tap with a 3/4"
thread.
Do not use already employed hoses for water
connection.
5. Very carefully slide out the right polythene bag,
removing it towards the left and then upwards.
P1088
P1126
P1127
The other end of the inlet hose which connects to the
machine can be turned in any direction. Simply
loosen the fitting, rotate the hose and retighten the
fitting, making sure there are no water leaks.
6. Set the machine upright and remove the
remaining rear screw. Slide out the relevant pin.
7
ENGLISH
Installation
132990671 GB.qxd
27/02/2004
10:11
Pagina
8
The drain hose must not be kinked. Run it along the
floor; only the part near the drainage point must be
raised.
P0021
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially
designed for this type of use.
P0023
Electrical connection
Water drainage
This machine is designed to operate on a 220-230 V,
single-phase, 50 Hz supply.
The end of the drain hose can be positioned in three
ways:
Check that your domestic electrical installation can
take the maximum load required (2.2 kW), also
taking into account any other appliances in use.
Hooked over the edge of a sink using the plastic
hose guide supplied with the machine. In this
case, make sure the end cannot come unhooked
when the machine is emptying.
This could be done by tying it to the tap with a piece
of string or attaching it to the wall.
Connect the machine to an earthed socket.
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution.
Should the appliance power supply cable
need to be replaced, this must be carried out
by our Service Centre.
Important!
When the appliance is installed the power supply
cable must be easily accessible.
P0022
In a sink drain pipe branch. This branch must be
above the trap so that the bend is at least 60 cm
above the ground.
Directly into a drain pipe at a height of not less
than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain pipe
must be larger than the outside diameter of the drain
hose.
8
132990671 GB.qxd
27/02/2004
10:11
Pagina
9
This new machine, which is fitted with the New Jet System, meets all modern requirements for effective
treatment of laundry with low water, energy and detergent consumption.
• The DELAY START option allows you to delay starting of the wash programme, so allowing you for instance
to make use of overnight economy electricity tariffs.
• The special HANDWASH programme
extreme care.
• The special wool programme
with its new delicate wash system treats your delicate items with
with its new delicate wash system treats your woollens with extreme care.
• The automatic cooling of the washing water from 90° to 60°C before draining will prevent old drain pipes
from being deformed.
• The balance control device ensures the machine is stable during the spin.
Description of the appliance
2
1
1 Detergent dispenser drawer
2 Control panel
3 Door handle
90°
4 Drain pump
60°
E
40° AA
700
600
40°
500
30°
450
E
FUNCTION
PROGRAM
START/PAUSE
EWF 734
5 Adjustable feet
3
4
5
Detergent dispenser drawer
Prewash
Main wash
Fabric softener, starch
Bleaching agent
Cl
C0115
9
ENGLISH
Your new washing machine
132990671 GB.qxd
27/02/2004
10:11
Pagina
10
Use
Control panel
90°
E
40° AA
700
60°
600
40°
500
30°
450
E
FUNCTION
PROGRAM
1
2
1 Detergent dispenser drawer and
programme chart
3 4
START/PAUSE
5
EWF 734
6 8 9
7
3 TEMPERATURE button
Press this button repeatedly to increase or decrease
the temperature, if you want your laundry to be washed
at a temperature different from the one proposed by the
washing machine. The relevant light will light up.
Maximum temperatures are 90°C for cotton, 60°C for
synthetic fabrics, 40°C for delicate fabrics, wool and
fabrics to be hand-washed (HANDWASH programme),
30°C for silk and
.
A programme chart in Portuguese and Greek is
provided with the instruction booklet. Insert it in the
interior part of the detergent dispenser drawer.
2 Programme selector dial
The selector is divided into 5 sections:
• Synthetics (green section)
By selecting position
the machine will wash with
cold water. To be used for extremely delicate items,
such as curtains.
• Delicate, handwash, wool, silk, miniprogramme
, rinses, drain, spin and delicate spin (grey
section)
4 SPIN SPEED button
• Cotton (blue section)
O Reset programme/OFF
Press this button repeatedly to change the spin
speed, if you want your laundry to be spun at a
speed different from the one proposed by the
washing machine. The relevant light will light up.
E
Maximum speeds are:
40° AA
Model EWF 1034
• for cotton: 1,000 rpm;
• for synthetic fabrics, wool, and fabrics to be
handwashed: 900 rpm;
• for delicate fabrics, silk and
: 700 rpm.
E
The selector dial can be turned either clockwise or
anticlockwise.
Position E
corresponds to the ENERGY SAVING
programme.
Model EWF 934
At the end of the programme the selector dial
must be turned to position O.
Model EWF 734
• for cotton, synthetic fabrics, wool, and fabrics to be
handwashed: 900 rpm;
• for delicate fabrics, silk and
: 700 rpm.
• for cotton, synthetic fabrics, wool, and fabrics to be
handwashed: 700 rpm;
• for delicate fabrics, silk and
: 600 rpm.
10
27/02/2004
10:11
Pagina
11
• NO SPIN
: by selecting this option all the
spinning phases are suppressed. To be used for
extremely delicate items.
The machine will add 3 rinses on cotton
programmes and 1 rinse on synthetic programme.
EXTRA RINSE: this option can be selected with
all programmes except the wool and handwash
programme. The machine will perform 2 additional
rinses for cotton and 1 rinse for synthetics, delicates
and silk.
To be used in areas where the water is very soft or
for people allergic to detergents or who have very
delicate skin.
5 Programme option buttons
Depending on the program, different functions can be
combined. These must be selected after choosing the
desired program and before depressing the
START/PAUSE button.
When these buttons are pressed, the corresponding
pilot lights come on. When they are pressed again,
the pilot lights go out.
If an incorrect option is selected, the pilot lights flash
for about 2 seconds and the message Err is
displayed.
Press these buttons to select the following options:
6 DELAY START button
The wash programme can be delayed from 30 min 60 min - 90 min, 2 hours and then by 1 hour up to a
maximum of 23 hours by means of this button.
Selecting the delayed start
• Select the programme and the required options.
• Select the delay start.
• Depress START/PAUSE button: the machine
starts its hourly countdown.
The programme will start after the selected delay has
expired.
PREWASH: select this option if you wish your
laundry to be prewashed before the main wash (not
available for wool and handwash cycle,
miniprogramme and silk).
The Prewash ends with a short spin at 650 rpm in
programmes for cotton and synthetic fabrics, whereas
in the program for delicate fabrics the water is only
drained.
Altering the delayed start
• Depress START/PAUSE button
• Depress START/PAUSE button again
QUICK WASH: this option can be used for lightly
soiled (not for wool, hand wash, silk and
miniprogramme) in order to obtain a good washing
program in a short time. The washing time will be
reduced according to the type of fabric and the
selected temperature.
Quick wash
cannot be used with E
E
program.
.
• Depress DELAY START button until “0h” is
displayed.
.
7 DISPLAY
The display shows the following information:
Duration of the programme - Delayed start Incorrect option selection - Alarm code - End of
programme.
, 40° AA,
Duration of the selected
programme
RINSE HOLD: by selecting this option the water of
the last rinse is not emptied out to prevent the fabrics
from creasing. When the programme has finished the
light of the START/PAUSE
goes off, the
light
and the light
are on to indicate that the water
must be emptied out.
After selecting a programme, the duration is
displayed in hours and minutes ( for example 2.05).
There are 2 possibilities to empty out water:
• Select programme
(draining):
The water is emptied out without spinning.
Attention! Before selecting programme
the
selector dial has to be positioned on 0 (cancelling).
• Select programme
or
. Select the spin
speed by means of the relevant button and then
depress the START/PAUSE button. The water is
emptied out and the laundry is spun at the selected
spin speed.
The duration is calculated automatically on the basis of
the maximum recommended load for each type of fabric.
After the programme has started, the time remaining
is updated every minute
11
ENGLISH
132990671 GB.qxd
132990671 GB.qxd
27/02/2004
10:11
Pagina
12
Delayed start
End of programme
The selected delay (23 hours max) set by means of
the relevant button appears on the display for 3
seconds, then the duration of the previously selected
programme is displayed.
When the programme has finished a flashing zero
is displayed.
The countdown is updated every hour and when
remain the last 2 hours each 30 min.
8 START/PAUSE button
Incorrect option selection
If an option which is not compatible with the set wash
programme is selected, the message Err is
displayed for 2 seconds.
START/PAUSE
This button has two functions: Start - Pause.
• Start:
After having selected the required programme, press
this button to start the machine; the corresponding
pilot light stops flashing.
If you have selected the delayed start, the machine
begins its countdown. The duration of the
programme or the delay appears on the display.
Alarm codes
• Pause
To interrupt a programme which is running, depress
the Start/Pause button: the corresponding pilot light
starts start to flash.
In the event of operating problems, some alarm
codes can be displayed, for example E20 (see
paragraph “Something not working”).
To restart the programme from the point at which it
was interrupted, press the START/PAUSE button
again.
12
27/02/2004
10:11
Pagina
13
9 Programme progress display
Programme information
By selecting the wash programme, the pilot lights
corresponding to the various phases making up the
programme come on.
Rinses
With this programme it is possible to rinse and spin
cotton garments which have been washed by hand.
The machine performs 3 rinses, followed by a final
spin at maximum speed.
The spin speed can be reduced by depressing
button
. The final spin is foreseen only for cotton
items as in the spin programme.
After the machine has started, only the running
phase pilot light stays on.
Drain
For emptying out the water of the last rinse in
programmes with the Rinse hold
option.
At the end of the programme the pilot light
illuminates.
The pilot light
flashes in the event of operating
problems and the relative alarm code appears on the
display:
Turn first the programme selector dial to O, then select
programme
and depress the START/PAUSE button.
- E40 = the door has not been closed
- E20 = the machine does not empty
- E10 = the machine does not fill
Separate long spin at max.speed for hand washed
garments. It has to be used for cotton items. You can
reduce the speed by means of button
to adapt it
to the fabrics to be spun.
Spin
To eliminate the problem, see paragraph “Something
not working”.
Delicate Spin
Separate short spin at 700 rpm (600 rpm - EWF 734)
for hand washed garments. It has to be used for
synthetic, delicate, wool/handwashed, silk items. You
can reduce the speed by means of button
to
adapt it to the fabrics to be spun.
Mini programme
This is a complete programme that can be
combined with the following options: spin speed
reduction, rinse hold and delayed start.
To be used for laundry which is lightly soiled or
which needs freshening up.
Max load 2.5 kg;
Washing temperature 30°C
Programme duration 30 minutes
Final spin speed 700 r.p.m (600 rpm - EWF 734).
O = Cancelling/OFF
To reset a programme and to switch off the machine
turn the selector dial to O. Now can a new
programme be selected.
13
ENGLISH
132990671 GB.qxd
132990671 GB.qxd
27/02/2004
10:11
Pagina
14
Washing hints
Laundry weights
The following weights are indicative:
Sorting the laundry
bathrobe
Follow the wash code symbols on each garment
label and the manufacturer’s washing instructions.
Sort the laundry as follows:
whites, coloureds, synthetics, delicates, woollens.
1200 g
napkin
100 g
quilt cover
700 g
sheet
500 g
pillow case
200 g
Temperatures
tablecloth
250 g
90°-95° for normally soiled white cottons and linen
towelling towel
200 g
60°
(e.g. tea cloths, towels, tablecloths,
sheets...)
tea cloth
100 g
night dress
200 g
for normally soiled, colour fast garments
(e.g. shirts, night dresses, pyjamas....) in
linen, cotton or synthetic fibres and for
lightly soiled white cotton (e.g. underwear).
ladies’ briefs
100 g
man’s work shirt
600 g
man’s shirt
200 g
man’s pyjamas
500 g
blouse
100 g
men’s underpants
100 g
(cold)for delicate items (e.g. net curtains), mixed
30°-40° laundry including synthetic fibres and
woollens bearing the label «pure new
wool, machine washable, non-shrink».
Before loading the laundry
Removing stains
Never wash whites and coloureds together. Whites
may lose their “whiteness” in the wash.
Stubborn stains may not be removed by just water
and detergent. It is therefore advisable to treat them
prior to washing.
New coloured items may run in the first wash; they
should therefore be washed separately the first time.
Blood: treat fresh stains with cold water. For dried
stains, soak overnight in water with a special
detergent then rub in the soap and water.
Make sure that no metal objects are left in the
laundry (e.g. hair clips, safety pins, pins).
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab the
stain; treat several times.
Button up pillowcases, close zip fasteners, hooks
and poppers. Tie any belts or long tapes.
Remove persistent stains before washing. Rub
particularly soiled areas with a special detergent or
detergent paste.
Dried grease stains: moisten with turpentine, lay
the garment on a soft surface and dab the stain with
the fingertips and a cotton cloth.
Treat curtains with special care. Remove hooks or tie
them up in a bag or net.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust
stains which are not recent since the cellulose
structure will already have been damaged and the
fabric tends to hole.
Maximum loads
Recommended loads are indicated in the
programme charts.
Mould stains: treat with bleach, rinse well (whites
and fast coloureds only).
General rules:
Grass: soap lightly and treat with bleach (whites and
fast coloureds only).
Cotton, linen: drum full but not too tightly packed;
Synthetics: drum no more than half full;
Ball point pen and glue: moisten with acetone (*),
lay the garment on a soft cloth and dab the stain.
Delicate fabrics and woollens: drum no more than
one third full.
Lipstick: moisten with acetone as above, then treat
stains with methylated spirits. Remove any residual
marks from white fabrics with bleach.
Washing a maximum load makes the most efficient
use of water and energy.
For heavily soiled laundry, reduce the load size.
Red wine: soak in water and detergent, rinse and
treat with acetic or citric acid, then rinse. Treat any
14
27/02/2004
10:11
Pagina
15
residual marks with bleach.
Quantity of detergent to be used
Ink: depending on the type of ink, moisten the fabric
first with acetone (*), then with acetic acid; treat any
residual marks on white fabrics with bleach and then
rinse thoroughly.
The type and quantity of detergent will depend on
the type of fabric, load size, degree of soiling and
hardness of the water used.
Water hardness is classified in so-called “degrees” of
hardness. Information on hardness of the water in
your area can be obtained from the relevant water
supply company, or from your local authority.
Tar stains: first treat with stain remover, methylated
spirits or benzine, then rub with detergent paste.
(*) do not use acetone on artificial silk.
Follow the product manufacturers’ instructions on
quantities to use.
Detergents and additives
Use less detergent if:
Good washing results also depend on the choice of
detergent and use of the correct quantities to avoid
waste and protect the environment. Although
biodegradable, detergents contain substances
which, in large quantities, can upset the delicate
balance of nature.
– you are washing a small load,
– the laundry is lightly soiled,
– large amounts of foam form during washing.
Degrees of water hardness
The choice of detergent will depend on the type of
fabric (delicates, woollens, cottons, etc.), the colour,
washing temperature and degree of soiling.
Degrees
All commonly available washing machine detergents
may be used in this appliance:
Level
Characteristic
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (60°C max)
and woollens,
1
soft
– liquid detergents, preferably for low temperature
wash programmes (60°C max) for all types of
fabric, or special for woollens only.
2
medium
3
hard
The detergent and any additives must be placed in
the appropriate compartments of the dispenser
drawer before starting the wash programme.
4
very hard
If using concentrated powder or liquid detergents, a
programme without prewash must be selected.
The washing machine incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked
just before starting the
programme.
Any fabric softener or starching additives must be
poured into the compartment marked
before
starting the wash programme.
The bleaching agent (chlorine) can be used only for
white or fast coloured cotton and linen items.
Pour it into the compartment marked
.
Follow the product manufacturer’s recommendations
on quantities to use and do not exceed the «MAX»
mark in the detergent dispenser drawer.
15
German
°dH
French
°T.H.
0- 7
0-15
8-14
16-25
15-21
26-37
more than more than
21
37
ENGLISH
132990671 GB.qxd
132990671 GB.qxd
27/02/2004
10:11
Pagina
16
International wash code symbols
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Energetic wash
95
60
40
30
Max. wash
temperature
95°C
Max. wash
temperature
60°C
Max. wash
temperature
40°C
Max. wash
temperature
30°C
Delicate wash
60
Bleaching
Bleach in cold water
40
Hand wash
30
40
Do not
wash
at all
Do not bleach
Ironing
Hot iron
max 200°C
Warm iron
max 150°C
Lukewarm iron
max 110°C
Do not iron
Dry cleaning
Dry cleaning
in all solvents
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
Dry cleaning
in petrol,
pure alcohol
and R 113
Do not
dry clean
high
temperature
low
temperature
Drying
Flat
On the line
On clothes
hanger
16
Tumble dry
Do not
tumble dry
27/02/2004
10:11
Pagina
17
4. Switch the machine ON
Operating sequence
Turn the selector dial to the desired programme to
switch the appliance on.
To switch the appliance off turn it to «O».
Before washing your first load of laundry, we
recommend that you run a cotton cycle at 60°C, with
the machine empty, in order to remove any
manufacturing residue from the drum and tub.
Pour half a measure of detergent into the main wash
compartment and start up the machine.
1. Place the laundry in the drum
Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
5. Select the desired programme
Close the door.
Turn the selector dial to the desired position: the
lights corresponding to the different phases making
up the selected programme light on.
P0004
2. Measure out the detergent
The duration of the programme appears in the
display.
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent recommended by the
manufacturer in a graduated cup and pour it into the
main wash compartment
.
6. Select the temperature
Press the Temperature button if you wish to select
a temperature value different from the one proposed
by the washing machine. The relevant light will light
up.
If you wish to carry out a programme with prewash,
pour detergent into the appropriate compartment
marked
.
3. Measure out the additives
90°
60°
If required, pour fabric softener into the compartment
marked
and the bleach into the compartement
marked
, without exceeding the «MAX» mark.
C0116
40°
30°
C0117
17
ENGLISH
132990671 GB.qxd
132990671 GB.qxd
27/02/2004
10:11
Pagina
18
7. Select the Spin Speed
NO SPIN
option.
9. Select the DELAY START
or the
To delay starting of the programme, press the
DELAY start button. The figures corresponding to the
selected delay will be displayed for about 3 seconds,
after which the duration of the selected programme
will appear on the display.
Press the SPIN SPEED button repeatedly, in
order to select the desired spin speed or the No spin
option. The relevant light will light up.
EWF 734
EWF 934
700
900
600
700
500
600
450
500
During this period it is possible to load other laundry:
EWF 1034
• depress START/PAUSE button;
1000
• open the door;
900
• load the laundry;
700
• close the door and depress START/PAUSE button
again.
500
10. Start the programme
Press the START/PAUSE button
. The relevant
light will stop flashing and only the light relevant to
the phase that is in progress will remain lit.
If you have chosen a delayed start, the washing
machine will begin the countdown.
The display will show the duration of the programme
or the selected delay.
8. Select the desired options
The light corresponding to the depressed button
illuminates.
11. Altering a programme
You can alter the programme before it starts.
When the programme has started, you can only
reset it by turning the programme selector dial to O
and then you can select the new programme. Start it
by depressing the START/PAUSE button
.
If you select the Rinse hold
option, the machine
will stop at the end of the programme with the water
still in the tub.
12. Interrupting a programme
Depress the START/PAUSE button
to interrupt a
programme which is running, the corresponding light
starts to flash. Depress the same button again to
restart the programme.
13. Cancelling a programme
Turn the selector dial to «0» to cancel a programme
which is running. Now you can select a new
programme.
18
27/02/2004
10:11
Pagina
19
ENGLISH
132990671 GB.qxd
14.How to open the door after the
programme has started
First set the machine to PAUSE by pressing the
START/PAUSE button.
If the door does not open, this means that the
machine is already heating, that the water level is
above the bottom edge of the door or that the drum
is turning.
If you cannot open the door but you need to open it
you have to switch the machine off turning the
selector dial to 0 . After about 3 minutes the door can
be opened (pay attention to the water level and
temperature!). To restart the programme switch on
the machine and select again the desired
programme and options.
15. At the end of the programme
The washing machine stops automatically.
If the Rinse hold
option has been selected, the
light of the START/PAUSE button goes off,
and
remain lit, to indicate that the water
must be drained before opening the door. The
display shows a flashing zero.
Turn the programme selector dial to Reset “O” to
switch the machine off.
Remove the laundry from the drum and carefully
check that the drum is empty so as to avoid any
forgotten items being damaged in a subsequent
wash (e.g. shrinking) or their colour running into a
load of whites.
If you do not intend to carry out another wash, close
the water tap.
Leave the door open to prevent the formation of
mildew and unpleasant smells.
19
132990671 GB.qxd
27/02/2004
10:11
Pagina
20
Programme table
Washing Programmes for cottons
Type of laundry
White cotton: e.g.
sheets, tablecloths,
household linen
Coloured cotton:
e.g. shirts, blouses,
underwear, towels,
house-hold linen
Cottons
ECONOMY**: e.g.
shirts, blouses,
underwear
Max
load
5 kg
Main wash at
(cold)-90°C
3 rinses
(cold)-90°C
Long spin
5 kg
5 kg
Main wash at
(cold)-60°C
3 rinses
(cold)-60°C
Long spin
1.9
45
2.20
1.1
42
1.59
0.850
42
2.04
0.95
44
2.10
0.85
50
1.27
0.6
44
1.27
Coloured
Cotton
5 kg
Synthetics
ECONOMY
Consumption*
Description of
Available options
programme
Energy Water Time
kWh
litres h/min.
White cotton
White/Coloured
Cottons 40°AA***
Synthetics: e.g.
shirts, blouses,
underwear
Programme/
temperature
and synthetics
Cottons
ECONOMY
E 60°/40°C
E
Main wash at
E 60°/40°C
2 rinses
Long spin
White/coloured Main wash at
40°C
cotton
3 rinses
40°AA
Long spin
Main wash at
(cold)-40°C
(cold)-60°C
3 rinses
Short spin
Synthetics
2.5 kg
2.5 kg
Synthetics
Main wash at
ECONOMY E 40°C
E
E40°C 3 rinses
Short spin
*
The consumption data shown on this chart is to be considered purely indicative, as it may vary depending
on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. It refers
to the highest temperature for each wash programme.
** In compliance with EC directive 92/75 the consumption figures indicated on the Energy label refer to this
programme E
at 60°C.
*** Fabrics washed with this programme have a washing efficiency result of AA.
The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable
Woolmark products provided that the garments are washed according to the instructions on the garment label
and those issued by the manufacturer of this machine. Licence No. M9605.
20
132990671 GB.qxd
27/02/2004
10:11
Pagina
21
Washing programmes for delicates
Type of laundry
Delicates: e.g.
acrylic fabrics,
viscose, polyester,
synthetic blends
Max
load
2,5 kg
Programme/
temperature
Energy Water
kWh
litres
Time
h/min.
Main wash at
(cold)-40°C
3 rinses
Short spin
0.35
52
57
Main wash at
(cold)-40°C
3 rinses
Short spin
0.35
52
57
0.30
50
39
30°C
Main wash at 30°C
3 rinses
Short spin
Miniprogramme
30°C
Main wash at 30°C
2 rinses
Short spin
0.3
40
30
2 kg
- 40°C
Silk
Miniprogramme
Consumption
58
2 kg
1 kg
2,5 kg
Available
options
53
Wool
Silk
and silk
0.55
-40°C
- 40°C
Wool
Description of
programme
, wool
Main wash at
(cold)-40°C
3 rinses
Short spin
Delicates
Handwash
Handwash
, handwash
ENGLISH
Programme table
21
132990671 GB.qxd
27/02/2004
10:11
Pagina
22
Programme table
Special Programmes
Programme
selector dial
position
Spin
Delicate Spin
O
Reset/Off
Wash
load
max.
Consumption*
Programme
For rinsing items
3 rinses with
liquid additive,
if required.
Long spin at
max. speed
5 kg
0.05
45
45
For empting out the
water of the last
rinses of programmes with option
Water draining
/
-
-
2
Separate spin for
cottons
Drain and spin
at the max.
speed
5 kg
-
-
10
5 kg
-
-
6
/
-
-
-
Rinses
Drain
Addictional
functions
Programme
description
Separate spin for
synthetics, delicates, Drain and
wool/handwash and delicate spin
silk
For cancelling the
programme which is
running or to switch
the machine off.
22
Energy Water
kWh
litres
Time
min.
132990671 GB.qxd
27/02/2004
10:11
Pagina
23
Detergent can also accumulate inside the drawer
recess: clean it with an old toothbrush. Refit the
drawer after cleaning.
1. Bodywork
Clean the outside of the machine with soap and
water only. Rinse with clean water and dry with a soft
cloth.
Important: do not use methylated spirits, solvents or
similar products to clean the bodywork.
2. Door seal
Check from time to time the door seal and eliminate
eventual possible objects that could be trapped in
the fold.
P0038
4. Drain pump
The pump should be inspected if
• the machine does not empty and/or spin
• the machine makes an unusual noise during
draining due to objects such as safety pins, coins
etc. blocking the pump.
Proceed as follows:
P1050
• Disconnect the appliance.
• If necessary wait until the water has cooled down.
• Open the pump door.
3. Detergent dispenser drawer
After a while, detergents and fabric softeners leave
deposits in the drawer.
Clean the drawer from time to time by rinsing it under
a running tap. To remove the drawer from the
machine, press the button in the rear left-hand
corner.
To facilitate cleaning, the top part of the additive
compartments can be removed.
P1114
• Place a container close to the pump to collect any
spillage.
• Release the emergency emptying hose, place it in
the container and remove its cap.
• When no more water comes out, unscrew the
pump cover and remove the pump. Always keep a
rag nearby to dry up spillage of water when
removing the pump.
C0118
C0119
P1115
23
ENGLISH
Maintenance
132990671 GB.qxd
27/02/2004
10:11
Pagina
24
• Remove any objects from the pump impeller by
rotating it.
6. Emergency emptying out
If the water is not discharged, proceed as follows to
empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the pump door;
• place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove
its cap. The water should drain by gravity into the
bowl. Whe the bowl is full, put the cap back on the
hose. Empty the bowl. Repeat the procedure until
water stops flowing out;
• Put the cap back on the emergency emptying hose
and place the latter back in its seat.
• clean the pump if necessary as previously
described;
• replace the emergency emptying hose in its seat
after having plugged it;
• screw the pump cover again and close the door.
P1117
7. Frost precautions
• Screw the pump cover fully in.
• Close the pump door.
If the machine is installed in a place where the
temperature could drop below 0°C, proceed as
follows:
5. Water inlet filter
• Remove the plug from the socket.
• Close the water tap and unscrew the water inlet
hose from the tap.
If you notice that the machine is taking longer to fill,
check that the filter in the water inlet hose is not
blocked.
• Place the end of the emergency emptying hose
and that of the inlet hose in a bowl placed on the
floor and let water drain out.
Turn off the water tap.
Unscrew the hose from the tap.
• Screw the water inlet hose back on and reposition
the emergency emptying hose after having put the
cap on again.
Clean the filter with a stiff brush.
Screw the hose back onto the tap.
By doing this, any water remaining in the machine is
removed, avoiding the formation of ice and,
consequently, breakage of the affected parts.
When you use the machine again, make sure that
the ambient temperature is above 0°C.
P1090
24
132990671 GB.qxd
27/02/2004
10:11
Pagina
25
Problems which you can resolve yourself.
During machine operation it is possible that one of the following alarm codes appears on the display and at the
same time the light
starts to flash:
- E10: problem with the water supply
- E20: problem with water draining
- E40: door open
Once the problem has been eliminated, press the START/PAUSE button
all checks, the problem persists, contact your local Service Centre.
Problem
to restart the programme. If after
Possible cause
• The door is not firmly closed. (E40)
• The machine does not start up:
• The machine is not plugged in or there is no power
at the socket.
• The main fuse has blown.
• The START/PAUSE button has not been
depressed.
• The DELAY START option has been selected.
• The programme selector dial is not positioned.
• The water tap is closed. (E10)
• The machine does not fill:
• The inlet hose is squashed or kinked. (E10)
• The filter in the inlet hose is blocked. (E10)
• The door is not properly closed. (E40)
• The machine fills then empties
immediately:
• The end of the drain hose is too low. Refer to
relevant paragraph in “water drainage” section.
• The machine does not empty
and/or does not spin:
• The drain hose is squashed or kinked. (E20)
• The option
or
has been selected.
• The laundry is not evenly distributed in the drum.
• The drain pump is clogged. (E20)
• Too much detergent or unsuitable detergent
(creates too much foam) has been used.
• There is water on the floor:
• Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this
as the water runs down the hose; check to see if it
is damp.
• The drain hose is damaged.
• The cap on the emergency emptying hose has not
been replaced after cleaning the pump.
• Too little detergent or unsuitable detergent has
been used.
• Unsatisfactory washing results:
• Stubborn stains have not been treated prior to
washing.
• The correct temperature was not selected.
• Excessive laundry load.
25
ENGLISH
Something not working?
132990671 GB.qxd
27/02/2004
10:11
Pagina
26
Problem
Possible cause
• The machine vibrates or is
noisy:
• The transit bolts and packing have not been
removed.
• The support feet have not been adjusted.
• The laundry is not evenly distributed in the drum.
• Maybe there is very little laundry in the drum.
• The programme is still running.
• The door will not open:
• The door lock has not been released.
• There is water in the drum.
• The electronic unbalance detection device has cut
in because the laundry is not evenly distributed in
the drum. The laundry is redistributed by reverse
rotation of the drum. This may happen several
times before the unbalance disappears and normal
spinning can resume. If, after 10 minutes, the
laundry is still not evenly distributed in the drum,
the machine will not spin. In this case, redistribute
the load manually and select the spin programme.
• Spinning starts late or the
machine does not spin:
Water is not
visible in the machine. The machine,
which is the result of modern technology, runs
in a very economical way with low water
consumption. Performance is
nevertheless excellent.
The machine makes an unusual
noise. The machine is fitted with a commutator
motor which improves machine
performance.
P1035UK
P1034UK
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning, make
a note of the model, serial number and purchase
date of your machine: the Service Centre will require
this information.
Mod. ..........
Prod. No. ...........
Ser. No. .........
Mod. ..........
Prod. No. ...........
P0042
26
Ser. No. .........
132990671 GB.qxd
27/02/2004
10:11
Pagina
27
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising