Electrolux | EW878F | User manual | Electrolux EW878F User Manual

Electrolux EW878F User Manual
124970910-EW878F-GB
26-05-2000
15:48
Pagina 1
(Nero/Process Black pellicola)
W A S H I N G M AC H I N E
ÇAMAÇIR MAKINESI
INS T RUCTION BO O KL ET
KULLANIM KILAVUZ U
EW 878
F
GB
124 970 910
TR
Dear customer,
Please read these operating instructions carefully
and pay particular attention to the safety notes
indicated in the first pages. We recommend that you
keep this instruction booklet for future reference and
pass it on to any future owners.
Transport damages
When unpacking the appliance, check that it is not
damaged. If in doubt, do not use it and contact the
Service Centre.
The symbols you will see on some paragraphs of this booklet have the following meaning:
The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly
important for your safety or correct functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use of
the appliance.
Tips and information about economical and ecological use of the machine are marked with this symbol.
Our contribution to the protection of the
environment: we use recycled paper.
2
Warnings
Disposal
Maintenance
4-5
Bodywork
5
Tips for environmental protection 5
Technical specifications
6
Installation
7
Unpacking
7
Positioning
7
Water inlet
7
Water drainage
8
Electrical connection
8
Your new washing machine
9
Description of the appliance
9
Detergent dispenser drawer
Use
10
Control panel
10
Controls
10
Washing hints
11
Sorting the laundry
11
Temperatures
11
Before loading the laundry
11
Maximum loads
11
Laundry weights
11
Removing stains
11
Detergents and additives
12
International wash code symbols
13
Operating sequence
14-15
Washing programmes
16-17
3
18
Detergent dispenser drawer
18
Drain filter
18
Water inlet filter
18
Emergency emptying out
19
Frost precautions
19
Something not working?
9
18
20-21
ENGLISH
Contents
Warnings
The following warnings are provided in the interests of overall safety. You must read them carefully before
installing or using the appliance.
Installation
• Leave the porthole door slightly ajar when the
appliance is not in use. This preserves the door
seal and prevents the formation of musty smells.
• All internal packing must be removed before using
the appliance. Serious damage may be caused to
the machine or adjacent furniture if the protective
transit devices are not removed or are not
completely removed. Refer to the relevant
paragraph in the instruction book.
• Always check that water has emptied out before
opening the door. If not, drain the water following
the instructions in the instruction book.
• Always unplug the appliance and shut the water
tap after use.
• Any electrical work required to install this appliance
must be carried out by a qualified electrician.
General safety
• Any plumbing work required to install this
appliance must be carried out by a qualified
plumber.
• After having installed the machine, check that it is
not standing on its electrical supply cable.
• Repairs to the machine must be carried out only by
qualified personnel. Repairs carried out by
inexperienced persons could cause serious
danger. Contact your local Service Centre.
• If the appliance is placed on a carpeted floor,
ensure that air can circulate freely between the feet
and the floor.
• Never pull the power supply cable to remove the
plug from the socket; always take hold of the plug
itself.
Use
• During high temperature wash programmes the
door glass may get hot. Do not touch it!
• This appliance is designed for domestic use. It
must not be used for purposes other than those for
which it was designed.
• Only wash fabrics which are designed to be
machine washed. Follow the instructions on each
garment label.
• Do not overload the appliance. Follow the
instructions in the instruction book.
• Make sure that all pockets are empty. Objects such
as coins, safety pins, pins and screws can cause
extensive damage.
• Do not machine wash garments saturated with
petroleum, methylated spirits, trichlorethylene, etc.
If such fluids have been used to remove stains
prior to washing, wait until they have completely
evaporated from the fabric before placing garments
in the appliance.
• Place small items such as socks, belts, etc. in a
cloth bag or pillowcase to prevent them getting
trapped between the drum and the tub.
• Use only the recommended quantities of fabric
softener. An excessive amount could damage the
laundry.
4
• Keep all detergents in a safe place out of children’s
reach.
• Children are often not aware of how dangerous
electrical appliances can be. When the machine is
working, children should be carefully supervised
and not be allowed to play with the appliance.
• Make sure that children or pets do not climb into
the drum.
• When the appliance is to be scrapped, cut off the
electrical supply cable and destroy the plug with
the remaining cable. Disable the door catch in
order to prevent children from becoming trapped
inside while playing.
• The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children - danger
of suffocation! Keep them out of children’s reach.
Disposal
Packaging materials
The materials marked with the symbol
recyclable.
Machine
are
Use authorised disposal sites for your old appliance.
Help to keep your country tidy!
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
Tips for environmental protection
To save water, energy and to help protect the
environment, we recommend that you follow these
tips:
• With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
• Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
• Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
• The machine works more economically if it is fully
loaded.
5
ENGLISH
Child safety
Technical specifications
DIMENSIONS
Height
Width
Depth
85 cm
60 cm
54 cm
MAXIMUM LOAD
Cotton
Synthetics
Delicates
Woollens
5 kg
2 kg
2 kg
1 kg
SPIN SPEED
800 rpm max.
POWER SUPPLY VOLTAGE/FREQUENCY
TOTAL POWER ABSORBED
MINIMUM FUSE PROTECTION
220-230 V/50 Hz
2200 W
10 A
WATER PRESSURE
5 N/cm2
80 N/cm2
Minimum
Maximum
This appliance complies with the following EEC Directives:
73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility.
6
Unpacking
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that the
machine does not touch the wall or other kitchen
units.
Carefully level by screwing the adjustable feet in or
out. Never place cardboard, wood or similar
materials under the machine to compensate for any
unevenness in the floor.
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
1. Using a spanner, unscrew and remove the rear
right-hand bolt and lay the machine on its back,
taking care not to squash the hoses. This can be
avoided by placing one of the corner packing
pieces between the machine and the floor.
P1051
Water inlet
P0255
2. Remove the polystyrene block from the bottom of
the machine and release the two plastic bags.
Connect the water inlet hose to a tap with a 3/4"
thread.
3. Carefully remove the right-hand bag (1) then the
left-hand bag (2) by pulling them towards the
centre of the machine.
The other end of the inlet hose which connects to the
machine can be turned in any direction. Simply
loosen the fitting, rotate the hose and retighten the
fitting, making sure there are no water leaks.
2
P1068
1
P1066
P1088
4. Set the machine upright and remove the two
remaining bolts from the back.
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially
designed for this type of use.
5. Pull out the three plastic spacers from the holes
into which the bolts were fitted.
6. Plug the open holes with the plugs which you will
find at the back of the appliance.
P0256
P0021
P0020
7
ENGLISH
Installation
Water drainage
Electrical connection
The end of the drain hose can be positioned in three
ways:
This machine is designed to operate on a 220-230 V,
single-phase, 50 Hz supply.
Hooked over the edge of a sink using the plastic
hose guide supplied with the machine. In this
case, make sure the end cannot come unhooked
when the machine is emptying.
This could be done by tying it to the tap with a piece
of string or attaching it to the wall.
Check that your domestic electrical installation can
take the maximum load required (2.2 kW), also
taking into account any other appliances in use.
Connect the machine to an earthed socket.
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution.
Should the appliance power supply cable
need to be replaced, this should be carried
out by our Service Centre.
Important! The power supply cable must be easily
accessible after installing the machine.
P0022
In a sink drain pipe branch. This branch must be
above the trap so that the bend is at least 60 cm
above the ground.
Directly into a drain pipe at a height of not less
than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain pipe
must be larger than the outside diameter of the drain
hose.
The drain hose must not be kinked. Run it along the
floor; only the part near the drainage point must be
raised.
P0023
8
This new machine meets all modern requirements for effective treatment of laundry with low water, energy and
detergent consumption.
• The temperature selector dial will allow you to choose the most suitable temperature for your laundry.
• The automatic cooling of the washing water from 90° to 60°C before draining will prevent old drain pipes
from being deformed.
• The balance control device ensures the machine is stable during the spin.
Description of the appliance
1 Detergent dispenser drawer
1
3
2 Programme chart
3 Control panel
800
400
YARIM
YÜK
SUDA
AÇMA
BEKLETME KAPAMA
4 Door handle
5 Drain filter
2
6 Adjustable feet
4
5
6
Detergent dispenser drawer
Prewash
Main wash
Fabric softener, starch
P1017
9
ENGLISH
Your new washing machine
Use
Control panel
800
400
YARIM
YÜK
SUDA
BEKLETME
1 2 3 4
AÇMA
KAPAMA
5 6
7
8
1 Programme chart
5 On/Off button AÇMA KAPAMA
It will help you to choose the most suitable washing
programme for your laundry.
Press this button to start the machine. The same
button is used to switch the machine off.
Before selecting a programme or changing an
ongoing programme the machine must be
switched off by depressing the On/Off button.
2 Spin speed reduction button 800
400
By depressing this button the spin speed is reduced
as follows:
● cotton and linen: from 800 to 400 rpm
● synthetics, delicates and wool: from 750 to
400 rpm.
6 Mains-on light
It comes on when the machine starts operating and
goes out at the end of the programme.
3 Half load button YARIM YÜK
7 Temperature selector dial
(thermostat)
Select this button to reduce water consumption on
the rinse cycle when washing a smaller load of
cottons or linens (max. load size=2.5 kg).
To select the washing temperature turn the dial to
the required value.
When your laundry is only lightly soiled, a cold wash
can be used (dial to position
).
4 Anti-crease button SUDA
BEKLETME
Use only with “gentle” programmes for synthetics,
delicates and wool.
The last rinse water is not emptied out, so as to
avoid creasing if the laundry is not removed from the
machine immediately after washing.
The water can be emptied out by pressing the button
again (emptying will be followed by a short spin) or
by selecting the drain programme “M”.
If the button is not pressed, the programmes end
with a short spin.
8 Programme selector dial
To select the required washing programme turn the
dial clockwise.
10
The following weights are indicative:
bathrobe
Sorting the laundry
Follow the wash code symbols on each garment
label and the manufacturer’s washing instructions.
Sort the laundry as follows:
whites, coloureds, synthetics, delicates, woollens.
Temperatures
95°
60°
for normally soiled white cottons and linen
(e.g. tea cloths, towels, tablecloths,
sheets...)
for normally soiled, colour fast garments
(e.g. shirts, night dresses, pyjamas....) in
linen, cotton or synthetic fibres and for
lightly soiled white cotton (e.g. underwear).
(cold)for delicate items (e.g. net curtains), mixed
30°-40° laundry including synthetic fibres and
woollens bearing the label «pure new
wool, machine washable, non-shrink».
1200 g
napkin
100 g
quilt cover
700 g
sheet
500 g
pillow case
200 g
tablecloth
250 g
towelling towel
200 g
tea cloth
100 g
night dress
200 g
ladies’ briefs
100 g
man’s work shirt
600 g
man’s shirt
200 g
man’s pyjamas
500 g
blouse
100 g
men’s underpants
100 g
Removing stains
Before loading the laundry
Stubborn stains may not be removed by just water
and detergent. It is therefore advisable to treat them
prior to washing.
Never wash whites and coloureds together. Whites
may lose their “whiteness” in the wash.
Blood: treat fresh stains with cold water. For dried
stains, soak overnight in water with a special
detergent then rub in the soap and water.
New coloured items may run in the first wash; they
should therefore be washed separately the first time.
Make sure that no metal objects are left in the
laundry (e.g. hair clips, safety pins, pins).
Button up pillowcases, close zip fasteners, hooks
and poppers. Tie any belts or long tapes.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab the
stain; treat several times.
Remove persistent stains before washing. Rub
particularly soiled areas with a special detergent or
detergent paste.
Dried grease stains: moisten with turpentine, lay
the garment on a soft surface and dab the stain with
the fingertips and a cotton cloth.
Treat curtains with special care. Remove hooks or tie
them up in a bag or net.
Maximum loads
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust
stains which are not recent since the cellulose
structure will already have been damaged and the
fabric tends to hole.
Recommended loads are indicated in the
programme charts.
Mould stains: treat with bleach, rinse well (whites
and fast coloureds only).
General rules:
Grass: soap lightly and treat with bleach (whites and
fast coloureds only).
Cotton, linen: drum full but not too tightly packed;
Ball point pen and glue: moisten with acetone (*),
lay the garment on a soft cloth and dab the stain.
Synthetics: drum no more than half full;
Delicate fabrics and woollens: drum no more than
one third full.
Lipstick: moisten with acetone as above, then treat
stains with methylated spirits. Remove any residual
marks from white fabrics with bleach.
Washing a maximum load makes the most efficient
use of water and energy.
Red wine: soak in water and detergent, rinse and
treat with acetic or citric acid, then rinse. Treat any
residual marks with bleach.
For heavily soiled laundry, reduce the load size.
11
ENGLISH
Laundry weights
Washing hints
Quantity of detergent to be used
Ink: depending on the type of ink, moisten the fabric
first with acetone (*), then with acetic acid; treat any
residual marks on white fabrics with bleach and then
rinse thoroughly.
The type and quantity of detergent will depend on
the type of fabric, load size, degree of soiling and
hardness of the water used.
Tar stains: first treat with stain remover, methylated
spirits or benzine, then rub with detergent paste.
(*) do not use acetone on artificial silk.
Water hardness is classified in so-called “degrees” of
hardness. Information on hardness of the water in
your area can be obtained from the relevant water
supply company, or from your local authority.
Detergents and additives
Follow the product manufacturers’ instructions on
quantities to use.
Good washing results also depend on the choice of
detergent and use of the correct quantities to avoid
waste and protect the environment. Although
biodegradable, detergents contain substances
which, in large quantities, can upset the delicate
balance of nature.
Use less detergent if:
– you are washing a small load,
– the laundry is lightly soiled,
– large amounts of foam form during washing.
The choice of detergent will depend on the type of
fabric (delicates, woollens, cottons, etc.), the colour,
washing temperature and degree of soiling.
Degrees of water hardness
All commonly available washing machine detergents
may be used in this appliance:
Degrees
Level
– powder detergents for all types of fabric,
Characteristic
– powder detergents for delicate fabrics (60°C max)
and woollens,
– liquid detergents, preferably for low temperature
wash programmes (60°C max) for all types of
fabric, or special for woollens only.
The detergent and any additives must be placed in
the appropriate compartments of the dispenser
drawer before starting the wash programme.
If using concentrated powder or liquid detergents, a
programme without prewash must be selected.
The washing machine incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked
just before starting the
programme.
Any fabric softener or starching additives must be
poured into the compartment marked
before
starting the wash programme.
Follow the product manufacturer’s recommendations
on quantities to use and do not exceed the «MAX»
mark in the detergent dispenser drawer.
12
1
soft
2
medium
3
hard
4
very hard
German
°dH
French
°T.H.
0- 7
0-15
8-14
16-25
15-21
26-37
more than more than
21
37
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Energetic wash
95
60
40
30
Max. wash
temperature
95°C
Max. wash
temperature
60°C
Max. wash
temperature
40°C
Max. wash
temperature
30°C
Hand wash
Delicate wash
60
Bleaching
Bleach in cold water
40
Do not
wash
at all
30
40
Do not bleach
Ironing
Hot iron
max 200°C
Warm iron
max 150°C
Lukewarm iron
max 110°C
Do not iron
Dry cleaning
Dry cleaning
in all solvents
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
Dry cleaning
in petrol,
pure alcohol
and R 113
Do not
dry clean
high
temperature
low
temperature
Drying
Flat
On the line
On clothes
hanger
13
Tumble dry
Do not
tumble dry
ENGLISH
International wash code symbols
4. Select the temperature
Operating sequence
Turn the dial to the required setting.
Before washing your first load of laundry, we
recommend that you run a cotton cycle at 60°C, with
the machine empty, in order to remove any
manufacturing residue from the drum and tub.
Pour half a measure of detergent into the main wash
compartment and start up the machine.
60
1. Place the laundry in the drum
M0042
Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
5. Select the required option(s)
Close the door.
Depress spin speed reduction 400 and/or half load
YARIM YÜK or anti-crease SUDA BEKLETME
button, if desired.
800
800
400
YARIM
SUDA
YÜK BEKLETME
P0004
2. Measure out the detergent
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent recommended by the
manufacturer in a graduated cup and pour it into the
main wash compartment
.
6. Select the programme and start
the machine
Turn the programme selector dial clockwise to the
required programme and press the ON/OFF button:
the mains on light comes on and the machine starts
to operate.
If you wish to carry out the prewash, pour detergent
into the appropriate compartment marked
.
3. Measure out the additive
If required, pour fabric softener into the compartment
marked
, without exceeding the «MAX» mark.
M0043
P1018
AÇMA
KAPAMA
B
P1019
14
P0033S
ENGLISH
7. At the end of the programme
The machine stops automatically. The mains on light
goes out.
If you have selected a programme which ends with
the water of the last rinse left in the tub (option
SUDA BEKLETME), drain the water before opening
the door. Select programme “M” (drain) or depress
again button SUDA BEKLETME.
Wait one or two minutes before opening the door to
give the electric locking mechanism time to release
it.
Depress the ON/OFF button again to switch the
machine off.
Remove the laundry.
Turn the drum by hand to make sure it is completely
empty, so as to avoid any forgotten items being
damaged in a subsequent wash (e.g. shrinking) or
their colour running into a load of whites.
Release any buttons which have been pressed.
Turn the water tap off and unplug the machine.
Leave the door ajar to air the machine.
15
Programme table
Washing programmes for cotton and linen
Max. load: 5 kg
Programme
Temp.
Additional
functions
Fabrics
Consumptions*
Energy
kWh
Water
lt
Duration
min.
2.4
75
145
A
60°-95°
WHITES WITH PREWASH, for
example work garments, sheets,
household linen, underwear, towels
800 YARIM
400 YÜK
B
60°-95°
WHITES WITHOUT PREWASH, for
example household linen, sheets,
shirts, underwear
800 YARIM
400 YÜK
2.1
59
130
B
40°-60°
COLOUREDS WITHOUT PREWASH,
for example shirts, blouses, terry
cloths, underwear
800 YARIM
400 YÜK
1.15
59
130
C
30°-40°
SHORT PROGRAMME
slightly soiled laundry
800 YARIM
400 YÜK
0.6
59
85
D
Rinses
COLD
This programme can be used for
rinsing hand washed garments
0.1
45
45
-
-
-
F
Long spin
Separate spin for cotton and linen
800 YARIM
400 YÜK
800
400
In compliance with EC directive 92/75, the consumption figures indicated on the energy label refer to the 60°C
wash programme for cotton (programme “B”) with a wash load of 4.5 kg.
* The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on
the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. It corresponds
to the highest temperature for each wash programme.
16
Washing programmes for synthetics, mixed fabrics, delicates and wool
Max. load: 2 kg, wool 1 kg
Programme
Temp.
Additional
functions
Fabrics
Consumptions*
Energy
kWh
Water
lt
Duration
min.
G
40°-60°
SYNTHETICS WITHOUT PREWASH, for example shirts, blouses,
mixed fabrics
800 SUDA
400 BEKLETME
0.9
55
85
H
30°-40°
DELICATES, for example curtains
800 SUDA
400 BEKLETME
0.5
55
60
J
30°-40°
WOOL
Special programme for garments
bearing the “Pure new wool, nonshrink, machine washable” label
0.5
52
55
800 SUDA
400 BEKLETME
800 SUDA
400 BEKLETME
0.06
40
32
800
400
-
-
12
-
-
6
K
Rinses
COLD
This programme can be used for
rinsing hand washed garments
L
Short
spin
Separate spin for synthetics,
delicates and wool
M
Drain
For emptying out the last rinse water
of these programmes with the anticrease option SUDA BEKLETME.
* The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on
the quantity and type of laundry, on the inlet water temperature and on the ambient temperature.
17
ENGLISH
Programme table
Maintenance
1. Bodywork
3. Drain filter
Clean the outside of the machine with warm water
and a neutral, non-abrasive household detergent.
Rinse with clean water and dry with a soft cloth.
The drain filter collects threads and small objects
inadvertently left in the laundry. Check regularly that
the filter is clean.
Important: do not use methylated spirits, solvents or
similar products to clean the bodywork.
Open the filter door.
Place a container under the filter and unscrew it.
2. Detergent dispenser drawer
After a while, detergents and fabric softeners leave
deposits in the drawer.
Clean the drawer from time to time by rinsing it under
a running tap. To remove the drawer from the
machine, press the button in the rear left-hand
corner.
P0011
To facilitate cleaning, the top part of the additive
compartments can be removed.
P0132
Pull out the filter.
Clean the filter under a running tap, then refit it,
screwing it fully in.
P1020
P1021
Detergent can also accumulate inside the drawer
recess: clean it with an old toothbrush. Refit the
drawer after cleaning.
P0133
P0040
4. Water inlet filter
If you notice that the machine is taking longer to fill,
check that the filter in the water inlet hose is not
blocked.
Turn off the water tap.
Unscrew the hose from the tap.
Clean the filter in the hose with a stiff brush.
P0038
Screw the hose back onto the tap.
18
ENGLISH
5. Emergency emptying out
If the water is not discharged (outlet pump is
blocked, filter or drain hose are clogged), proceed as
follows to empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• place a bowl on the floor;
• put the drain hose end into the bowl and let the
water come out.
Should it not be possible to have access to the outlet
hose because, for example, the appliance is built in
the kitchen furniture, slightly loosen the outlet filter
after placing a bowl on the floor, to let the water
come out slowly.
At the end screw the filter again.
6. Frost precautions
If the machine is installed in a place where the
temperature could drop below 0°C, proceed as
follows:
• Close the water tap and unscrew the water inlet
hose from the tap.
• Place the end of the drain hose and that of the inlet
hose in a bowl placed on the floor.
• Select programme “M” and run it until the machine
stops.
• Remove the plug from the socket.
• Screw the water inlet hose back on and put the
drain hose back in its place.
By doing this, any water remaining in the machine is
removed, avoiding the formation of ice and,
consequently, breakage of the affected parts.
When you use the machine again, make sure that
the ambient temperature is above 0°C.
19
Something not working?
Problems which you can resolve yourself.
Problem
Possible cause
• The machine does not start up:
• The door is not firmly closed.
• The machine is not plugged in or there is no power
at the socket.
• The main fuse has blown.
• The programme selector dial is not positioned correctly
and the ON/OFF button has not been depressed.
• The water tap is closed.
• The machine does not fill:
• The inlet hose is squashed or kinked.
• The filter in the inlet hose is blocked.
• The door is not properly closed.
• The machine fills then empties
immediately:
• The end of the drain hose is too low. Refer to
relevant paragraph in “water drainage” section.
• The machine does not empty
and/or does not spin:
• The drain hose is squashed or kinked.
• The option SUDA BEKLETME has been selected.
• The laundry is not evenly distributed in the drum.
• The drain filter is clogged.
• There is water on the floor:
• Too much detergent or unsuitable detergent
(creates too much foam) has been used.
• Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this
as the water runs down the hose; check to see if it
is damp.
• The drain hose is damaged.
• Unsatisfactory washing results:
• Too little detergent or unsuitable detergent has
been used.
• Stubborn stains have not been treated prior to
washing.
• The correct temperature was not selected.
• Excessive laundry load.
• The machine vibrates or is
noisy:
• The transit bolts and packing have not been
removed.
• The support feet have not been adjusted.
• The laundry is not evenly distributed in the drum.
• Maybe there is very little laundry in the drum.
• The programme is still running.
• The door will not open:
• The door lock has not been released.
• There is water in the drum.
20
Possible cause
• Spinning starts late or the
machine does not spin:
• The electronic unbalance detection device has cut
in because the laundry is not evenly distributed in
the drum. The laundry is redistributed by reverse
rotation of the drum. This may happen several
times before the unbalance disappears and normal
spinning can resume. If, after 5 minutes, the
laundry is still not evenly distributed in the drum,
the machine will not spin. In this case, redistribute
the load manually and reselect the spin
programme.
Water is not
visible in the machine. The machine,
which is the result of modern technology, runs
in a very economical way with low water
consumption. Performance is
nevertheless excellent.
The machine makes an unusual
noise. The machine is fitted with a commutator
motor which improves machine
performance.
P1035UK
P1034UK
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning, make
a note of the model, serial number and purchase
date of your machine: the Service Centre will require
this information.
Mod.
..........
Ser.
Mod. ..........
Prod. No. ...........
P0042
21
Ser. No. .........
ENGLISH
Problem
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising