Aeg-Electrolux | LTH57800 | User manual | Aeg-Electrolux LTH57800 User Manual

LAVATHERM 57800
Condensation dryer
User information
Dear customer,
Please read this User Information carefully and keep it to refer to at a
later date.
Pass this User Information on to any subsequent owner of the appliance.
1
3
2
2
The following symbols are used in the text:
Safety instructions
Warning: Notes that concern your personal safety.
Attention: Notes that show how to avoid damage to the appliance.
Useful tips and hints
Environmental information
Contents
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Environmental tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Description of machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Operating screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Overview of programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Before the first drying cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Sorting and preparing laundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching machine on / switching light on . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening loading door / filling laundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting additional functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTENSITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUDIBLE SIGNAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SENSITIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting time delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting the programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Putting in extra items or taking items out before end of programme . . . .
Drying cycle complete / removing laundry . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
13
13
13
13
14
14
14
14
15
15
15
15
Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning fluff filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the door seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emptying the water reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning heat exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the drum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clean operating screen and housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
16
17
18
18
20
20
What to do if … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Troubleshooting by yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Changing bulb for inside light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Consumption values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installation and connection instructions. . . . . . . . . . . . . . . . .
25
Installation safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Removing transport safety equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Changing door stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Special accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Guarantee/Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service
4
29
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Operating Instructions
1 Safety
Before first starting up
• Note the ”Installation and connection instructions”
• Before first starting up, check the machine for any damage incurred
during transport. Never connect up a damaged machine. If parts are
damaged, contact your supplier.
Intended use
• The dryer is intended for drying standard laundry in domestic applications.
• Conversions or modifications to the dryer are not permitted.
• This dryer is intended only for drying textile material washed in water.
• To minimize the risk of fire in a tumble dryer, the following should be
observed:
– Items that have been spotted or soaked with vegetable or cooking
oil constitute a fire hazard and should not be placed in a tumble
dryer.
– Oil-affected items can ignite sponteanously, especially when exposed to heat sources such as a tumble dryer. The items become
warm, causing an oxidation reaction in the oil. Oxidation creates
heat. If the heat cannot escape, the items can become hot enough
to catch fire. Piling, stacking or storing oil-affected items can prevent heat from escaping and so create a fire hazard.
– If it is unavoidable that fabrics that contain vegetable or cooking
oil or have been contamined by hair care products be placed in a
tumble dryer they should first be washed in hot water with extra
detergent - this will reduce, but not eliminate, the hazard. The „cool
down“ cycle of tumble dryers should be used to reduce the temperature of the items. They should not be removed from the tumble
dryer or piled or stacked while hot.
– Items that have been previously cleaned in, washed in, soaked or
spotted with petrol/gasoline, dry-cleaning solvents or other flammable or explosive substances should not be placed in a tumble
dryer.
– Highly flammable substances commonly used in domestic environments include acetone, denatured alcohol, petrol / gasoline, kerosene, spot removers (some brands), turpentine, waxes and wax
removers should not be placed in a tumble dryer.
5
– Items containing foam rubber (also known as latex foam) or similarly textured rubber-like materials should not be dried in a tumble
dryer on a heat setting. Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
– Fabric softeners or similar products should not be used in a tumble
dryer to eliminate the effects of static electricity unless this practice is specifically recommended by the manufacturer of the fabric
softener or product.
– Undergarments that contain metal reinforcements should not be
placed in a tumble dryer. Damage to the tumble dryer can result if
metal reinforcements come loose during drying. When available a
drying rack could be used for such items.
– Plastic articles such as shower caps or babies´waterproof napkin
covers should not be placed in a tumble dryer.
– rubber-backed articles, clothes fitted with foam rubber pads, pillows, galoshes and rubber-coated tennis shoes should not be placed
in a tumble dryer.
• When using dry-cleaning sets: Only use those products which are declared as suitable for the dryer by the manufacturer.
• Do not place heavily worn laundry items in the dryer. Risk of fire!
• Do not place laundry items with loose fillings (e.g. cushions) in the
dryer. Risk of fire!
• Parts with rigid components (e.g. door mats) may cover the air slots.
Risk of fire! Do not place such items in the dryer.
• Do not overfill the dryer. Risk of fire! Observe max. loading volume of
6 kg.
• Clean the micro-fine filter and fine strainer after each drying cycle.
• Never operate the dryer without fluff filters or with damaged or
blocked fluff filters. Risk of fire!
• Clean the heat exchanger regularly.
• With stacked washer and dryer: Do not place objects on the dryer.
These may fall off during operation.
• The covering bonnet of the bulb for the drum light must be screwed
down tightly.
Safety of children and infirm persons
• The appliance is not intended for use by young children or infirm persons without supervision.
• Children are often not aware of the dangers involved when handling
electrical equipment. Therefore provide the necessary supervision of
children when operating the appliance and do not let children play
6
with the dryer – there is a danger that children could become trapped
inside the appliance.
• Packaging parts (e.g. films, styropore) can be dangerous for children.
Danger of suffocation! Keep packaging parts out of reach of children.
• Make sure that children or small animals do not climb into the drum
of the dryer. For this purpose keep the door of the dryer closed when
the appliance is not in use.
General safety
• Only specialists may undertake repairs on the dryer.
• Never start up the dryer if the mains cable is damaged or if the operating screen, operating plate or base area are damaged so that the inside of the machine is open and accessible.
• Switch off the dryer before all cleaning, care or maintenance work.
Also disconnect the mains plug from the socket or – with permanent
connections – switch off the LS switch in the fuse box and/or fully
unscrew the screwed-in fuse.
• Disconnect the machine from the power supply during long pauses in
operations.
• When removing from the socket, never pull the mains plug by the cable, instead take a hold of the plug.
• Manifold plugs, couplings and extension cables must not be used.
Risk of fire from overheating!
• Do not spray down the dryer with jets of water. Risk of electric shock!
• Do not lean on the open door. The machine may tip over.
• Once the drying cycle has been interrupted, the laundry and drum
may be hot. Risk of burns! Take care when removing the laundry.
Disposal
2
Packaging material
The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging materials in the appropriate
container at the community waste disposal facilities.
7
2
Old appliance
W
1
The symbol
on the product or on its packaging indicates that this
product may not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you
purchased the product.
Warning! Remove mains plug from socket when you have no further
use for the machine. Cut off mains cable and dispose of together with
plug.
Destroy loading door lock. Children cannot then lock themselves in the
machine and put their lives at risk.
2 Environmental tips
• In the dryer, laundry becomes fluffy and soft. Fabric softeners are not
therefore needed when washing.
• Your dryer will function most economically if you:
– always keep the ventilation slots on the base of the dryer unobstructed;
– use the loading volumes specified in the programme overview;
– ensure you have good ventilation in the installation room;
– clean the micro-fine filter and fine strainer after each drying cycle;
– spin the laundry well before drying. Example: Consumption data –
depending on spinning speed – for 6kg of laundry, dried using the
COTTONS STORAGE DRY programme.
Pre-draining
Revolutions per
minute
8
Drying cycle
Residual dampness
Energy
in kWh
in litres
as a %
800
4.2
70
3,84
1000
3.6
60
3,36
1200
3.2
53
3,10
1400
3.0
50
3,00
1800
2.5
42
2,60
Description of machine
Drawer containing
condensate tank
Operating screen
Fine strainer
(lint filter)
Lamp for inside
light
Large mesh filter
(lint filter)
Micro-fine filter
(lint filter)
Type plate
Loading door
(interchangeable
stop)
Screwed feet
(with height
adjustment)
Base door
upstream of
heat exchanger
Air slots
Operating screen
INTENSITY button
Display showing
level of dryness
Multi-display
DELAY TIMER
button
Programme selector
Programme progress display
Block of buttons and displays
Maintenance displays
– HEAT EXCHANGER (clean!)
– EMPTY WATER(empty!)
– CLEAN FILTER (clean lint filter!)
9
Overview of programmes
max. loading volume
(weight when dry)
AUDIBLE SIGNAL
SPECIAL CARE1)
SENSITIVE 1)
INTENSITY
EXTRA DRY
6kg
•
•
•
•
Drying thick or multi-layered textiles, e.g. terry towelling items
mn
INTENSIVE
DRY
6kg
•
•
•
•
Drying thick textiles, e.g. terry
towelling items, towels.
mn
STORAGE
DRY
6kg
•
•
•
•
Drying textiles of even thicknesses, e.g. terry towelling items, knitted items, towels.
mn
DAMP
6kg
•
•
•
•
For thin textiles which are still to
be ironed, e.g. knitted items, cotton shirts.
mn
HAND
IRON
6kg
•
•
•
•
For normal thickness cotton or
linen laundry, e.g. bedding, table
linen.
mn
MACHINE
IRON
6kg
•
•
•
•
For cotton or linen laundry which
are still to be put through a machine, e.g. bedding, table linen.
mn
EXTRA DRY
3kg
•
•
•
•
Drying thick or multi-layered textiles, e.g. pullovers, bedding, table
linen.
m l2)
n
m l2)
n
m l2)
n
COTTONS
Programme
EASY CARES
Additional
functions
Application/properties
STORAGE
DRY
3kg
•
•
•
•
For thin textiles which are not
ironed, e.g. easy care shirts, table
linen, baby’s clothes, socks, underwear.
DAMP
3kg
•
•
•
•
For thin textiles which are still to
be ironed, e.g. knitted items, cotton shirts.
1) SPECIAL CARE and SENSITIVE cannot both be selected at the same time.
2) Press the SPECIAL CARE button!
10
Care
symbols
max. loading volume
(weight when dry)
AUDIBLE SIGNAL
SPECIAL CARE1)
SENSITIVE 1)
INTENSITY
Additional
functions
30 MIN
1kg
•
•
-
-
For drying individual items of laundry
or for small volumes of less than 1kg.
6kg
•
•
•
•
Special programme for leisure clothing, such as jeans, sweat-shirts, etc.,
of different material thicknesses (e.g.
at the cuffs and seams).
mn
LEISURE
m l2)
n
-
Special programme with anti-crease
feature for easy care textiles such
shirts and blouses; for minimum ironing effort. The result depends on the
type and quality of textiles. (The loading volume corresponds to approx. 5
to 7 shirts.)
Recommendation: Place textiles in the
dryer straight after spinning. Once
dried, immediately remove textiles
and place on clothes hanger.
-
Special programme for briefly treating
woollens with warm air after they
have been dried naturally, worn or
stored for long periods. Wool fibres
are aligned and the wool becomes
soft and snugly.
Recommendation: Remove textiles
immediately after drying.
-
Special programme, lasting around 35
minutes, for refreshing or gently
cleaning textiles with commercially
available dry cleaning sets.
(Only use those products which are
declared as suitable for the drier by
the manufacturer; please observe the
manufacturer’s instructions for use.)
Programme
EASY IRON
WOOL CARE
REFRESH
1kg
1kg
1kg
•
•
•
•
•
•
-
-
-
Application/properties
Care
symbols
m l2)
n
1) SPECIAL CARE and SENSITIVE cannot both be selected at the same time.
2) Press the SPECIAL CARE button!
11
Before the first drying cycle
In order to remove any residue which may have been produced during
production, wipe the dryer drum with a damp cloth or undertake a
brief drying cycle (30 MIN) with damp cloths.
Sorting and preparing laundry
Sorting laundry
• Sort by fabric type:
– Cotton/linen for programmes in COTTONS programme group.
– Mixtures and synthetics for programmes in EASY CARES programme group.
• Sorting by care label. The care labels mean:
n
m
l
k
Basic drying
in tumble
dryer possible
Drying
at normal
temperature
Drying
at reduced temperature
(press SPECIAL CARE
button!)
Drying
in tumble dryer
not possible
• Do not dry new, coloured textiles together with light-coloured laundry items. Textile colours may bleed.
• Do not dry tricot or knitted items with the EXTRA DRY programme.
Items may become stuck!
• Do not dry wool in the dryer. May become entangled! After air-drying, wool may be dried with the WOOL CARE programme.
Preparing laundry
• To avoid laundry becoming tangled: Close zips, button up coverings
and tie loose bands or ribbons (e.g. of aprons).
• Empty pockets. Remove metallic items (paperclips, safety pins etc).
• Turn items with double-layered fabrics inside out (e.g. with cottonlined anoraks, the cotton layer should be outermost). These fabrics
will then dry better.
12
Drying
Switching machine on / switching light on
Turn the programme selector to any programme or turn it to LIGHT. The
machine has been switched on. When the loading door is opened, the
drum is illuminated.
Opening loading door / filling laundry
1. Open loading door:
– Either use force to push against the loading door (push point
– or if the machine is switched on: Press the DOOR button.
2. Load your laundry (do not force it in).
)
1
Caution! Do not jam laundry in between the loading door and rubber
seal.
3. Close loading door securely. Lock must audibly lock.
Selecting the programme
Use the programme selector to set
the programme you require.
The probable programme run time
is displayed (in minutes) on the
multi-display.
Selecting additional functions
INTENSITY
Precise setting of humidity content
of laundry. Laundry becomes dryer
from + to +++.
1. Press the INTENSITY button as
many times as necessary until the
small light at the level of residual
dampness required is illuminated.
13
If required, press the AUDIBLE
SIGNAL, SPECIAL CARE or SENSITIVE buttons.
AUDIBLE SIGNAL
When the drying cycle has finished, an intermittent audible signal will
sound.
SPECIAL CARE
For especially gentle drying of sensitive fabrics with the l care label
and for temperature-sensitive textiles (e.g. acrylic, viscose). Programme
is executed with reduced heat.
SPECIAL CARE is only suitable for use with loads of up to 3kg!
SENSITIVE
3
For gentle drying of frequently-worn textiles. Programme starts on full
heat setting, which is then reduced towards the end of the programme
to ensure gentle care of laundry.
SPECIAL CARE and SENSITIVE cannot be selected together.
Setting time delay
3
3
14
With the DELAY TIMER button, you can delay the start of a programme
by between 30 minutes (30' and a maximum of 23 hours (23h).
1. Select the programme
2. Press the DELAY TIMER button as many times as necessary until the required start delay appears on the multi display, e.g. 12h if the programme is to be started in 12 hours. The DELAY TIMER display is
illuminated.
If 23h is displayed and you press the button again, the time delay will
be cancelled. The display will show 0' and then the duration of the selected programme.
3. To activate the delay timer, press the START/PAUSE button. The amount
of time remaining until the programme is set to start is continuously
displayed (e.g. 12h, 11h, 10h, … 30' etc).
Starting the programme
Press the START/PAUSE button. The programme is started.
The programme progress display and the display showing the level of
dryness show drying progress.
Changing programme
To change a programme which has been selected by mistake once the
programme has started, first turn the programme selector to OFF and
then reset the programme.
3
The programme can no longer be changed directly once the programme
has started. If nevertheless there is an attempt to change the programme on the programme knob, the programme progress display and
the maintenance indicators flash. If an option button (excluding the
AUDIBLE SIGNAL button) is pressed, Err appears in the multidisplay.
The drying programme is not however affected by this (laundry protection).
Putting in extra items or taking items out before end of
programme
1. Open door.
1
Warning! Laundry and drum can become hot. Risk of burns!
2. Load or remove laundry items.
3. Close door securely.
4. Press the START/PAUSE button to continue the drying cycle.
Drying cycle complete / removing laundry
3
Once the drying cycle is complete, the END and CREASE GUARD displays light up. If the AUDIBLE SIGNAL button has been pressed, an audible signal sounds intermittently.
The drying cycle is automatically followed by a crease guard phase
which lasts around 30 minutes. The drum rotates in intervals during
this phase. The laundry thereby remains relaxed and free of creases. The
laundry can be removed at any time during the crease guard phase.
(The laundry should be taken out towards the end of the crease guard
phase at the latest to prevent creases from forming.)
15
1. Open loading door
2. Before removing the laundry, remove lint from the micro-fine filter. It is
best to use a damp hand for this purpose (refer to “Cleaning and maintenance” section).
3. Remove laundry.
4. Turn the programme selector to OFF.
Important! After each drying cycle
– clean the micro-fine filter and fine strainer,
– drain the condensate tank
(refer to the “Cleaning and maintenance” section).
5. Close loading door.
Cleaning and maintenance
Cleaning fluff filter
1
To ensure that the dryer works perfectly, the fluff filters (micro-fine filter and fine strainer) must be cleaned after every drying cycle.
Caution! Never operate the dryer without fluff filters or with damaged
or blocked fluff filters.
1. Open loading door
2. Use a damp hand to clean the micro-fine filter, which is built into
the lower part of the loading aperture.
3. Push down unlock button on large
mesh filter.
Large mesh filter jumps up.
16
4. Take out fine strainer.
5. Remove fluff from fine strainer. It
is best to use a damp hand for this
purpose.
3
Clean the entire filter area
The strainer area does not have to be cleaned after every drying cycle,
but should be checked regularly and cleaned of fluff if necessary.
6. To do this, grip the top of the large
mesh filter and pull it forwards until it comes loose from the two
brackets.
7. Remove fluff from the entire filter
area. It is best to use a vacuum
cleaner for this purpose.
8. Press both journals of the large
mesh filter into the brackets on the
loading door until they snap into
place.
9. Re-insert fine strainer.
10. Press against the large mesh filter
until it locks into the interlock.
3
If the fine strainer is not fitted, the
large mesh filter will not snap into
place and the loading door cannot
be closed.
Cleaning the door seal
Wipe the door seal with a damp cloth immediately after the drying cycle has finished.
17
Emptying the water reservoir
1
Empty water reservoir after every drying cycle.
If the water reservoir is full, an active programme will be interrupted
automatically and the EMPTY WATER display will light up. In order to
continue the programme, the water reservoir must be emptied.
Warning! The condensed water is not suitable for drinking or for preparing foodstuffs.
1. Take out drawer containing water
reservoir completely (1) and pull up
the water reservoir’s drainage pipe
as far as it will go (2).
3
2. Pour condensed water out into a
sink or other suitable container.
3. Slide outlet connections in and refit water reservoir.
If the programme has been interrupted as a result of the water reservoir being full:
Press the START/PAUSE button to
continue the drying cycle.
3
The water reservoir has a volume of approx. 4 litres. This is sufficient for
around 6kg of laundry which has previously been spun at 800 revolutions/minute.
The condensed water can be used as distilled water, e.g. for steam ironing. However first filter it (e.g. with a coffee filter) to remove any residue and small pieces of fluff.
Cleaning heat exchanger
1
18
If the HEAT EXCHANGER display is illuminated, the heat exchanger
needs to be cleaned.
Caution! Operating when the heat exchanger is clogged with lint can
damage the dryer. This also increases energy consumption.
1. Open loading door
2. Open base door. To do this, press
the release button located beneath
the loading aperture and open the
base door to the left.
3. Remove lint from the inside of the
door and the heat exchange chamber. Wipe the door seal with a
damp cloth.
4. Turn both lock washers inwards.
5. Use the handle to pull the heat exchanger out of the base and carry
it horizontally to prevent any remaining water from spilling.
6. To empty the heat exchanger, hold
vertically over a washing-up bowl.
1
Caution! Do not use sharp objects
to clean the heat exchanger. You
could damage it an cause leaks.
7. Clean heat exchanger.
It is best to use a brush or to rinse thoroughly with a shower head.
8. Replace heat exchanger and lock into place (turn both lock washers
outwards until they snap into place).
9. Close base door.
3
1
The dryer will not operate if the HEAT EXCHANGER indicator is still lit.
Caution! Never operate the dryer without the heat exchanger.
19
Cleaning the drum
1
3
Caution! Do not use abrasives or steel wool to clean the drum.
Lime in the water or cleaning agents may form a barely visible lining on
the inside of the drum. The degree to which the laundry has been dried
is then no longer detected reliably. The laundry is damper than expected when removed from the dryer.
Use a standard domestic cleaner (e.g. vinegar-based cleaner) to wipe
down the inside of the drum and drum ribs.
Clean operating screen and housing
1
Caution! Do not use furniture cleaners or aggressive cleaning agents to
clean the machine.
Use a damp cloth to wipe down the operating screen and housing.
What to do if …
Troubleshooting by yourself
If, during operation, the error code (E plus number or letter) appears on
the multi-display: Switch the machine off and on again. Reset programme. Press the START/PAUSE button
If the error is still displayed, please inform your local Service Force Centre and quote the error code.
Problem
Possible cause
Remedy
Mains plug is not plugged in Plug in at mains socket. Check
or fuse is not working cor- fuse in fuse box (domestic inrectly.
stallation).
Dryer does not work.
Loading door is open.
Close loading door.
Have you pressed the START/ Press the START/PAUSE button
PAUSE button?
again.
20
Problem
Possible cause
Remedy
Select a different programme
the next time you dry (see
Wrong programme selected.
“Overview of programmes”
section).
Lint filter clogged.
Clean lint filter.
Heat exchanger clogged
with lint.
Clean heat exchanger.
Observe recommended loadDrying results unsatis- Overloading of laundry.
ing volumes.
factory.
Ventilation slots in base area Uncover ventilation slots in
covered up.
base area.
Residue on inside surface of Clean inside surface of drum
drum or drum ribs.
and drum ribs.
Make an adjustment using the
INTENSITY function (see chapter ”Drying, Selecting additional functions”).
Mains plug disconnected.
Loading door does not
open with DOOR but- Programme selector in OFF
ton.
position.
Plug in at mains socket.
Set programme. Loading door
can be opened at any time by
exerting pressure on the door.
Fine strainer not in place
Install fine strainer and/or
Loading door does not
and/or large mesh filter not snap large mesh filter into
close.
locked in place.
place.
When a button is
pressed, Err appears
in the multi-display.
Drum light does not
work.
Washing protection. After
the start of the programme, Turn the programme knob to
the option can no longer be OFF. Set the programme again.
set.
Programme selector in OFF
position.
Turn programme selector to
LIGHT or to any programme.
Defective light bulb.
Replace light bulb (see next
section).
PROGRAMME TIME
display changes erratically or stays unchanged for a long
time.
Programme time is corrected automatically depending
Automatic process; this is not
on type and volume of
a machine fault.
laundry and level of dampness.
Programme inactive,
EMPTY WATER display
illuminated.
Condensate tank is full.
Empty condensate tank, then
start programme with START/
PAUSE button.
21
Problem
Drying cycle ends
shortly after programme starts. END
display illuminated.
Drying cycle lasts an
unusually long time.
Note:
After around 5 hours
the drying cycle ends
automatically (see
„Drying cycle complete“).
Possible cause
Remedy
Select time programme or
Not enough washing loadhigher drying level (e.g. INTENed or washing loaded is too
SIVE DRY instead of STORAGE
dry for selected programme.
DRY).
Lint filter clogged.
Clean lint filter.
Heat exchanger clogged
with lint.
Clean heat exchanger.
SPECIAL CARE button
SPECIAL CARE is only suitable
pressed and load volume too for use with loads of up to
big.
3kg!
Load volume too big.
Reduce load volume.
Laundry insufficiently spun.
Laundry must be adequately
spun.
Changing bulb for inside light
1
1
Only use a special bulb which is designed specially for dryers. The special bulb is available from the after-sales service,
ET-Nr. 112 552 000-5.
Warning! Do not use standard bulbs! These develop too much heat and
may damage the machine!
Warning! Before replacing the bulb, disconnect the mains plug; with a
permanent connection: fully unscrew or deactivate the fuse.
1. Unscrew covering bonnet from above bulb (this can be found directly
behind the loading aperture, at the top; refer to “Description of machine” section.)
2. Replace defective bulb.
3. Screw covering bonnet back down.
1
22
Warning! For reasons associated with safety, the covering bonnet must
be screwed down tightly. If this is not done, the dryer must not be operated.
Programming options
Objective
Implementation
1. Turn the programme selector to any programme.
Permanently programme 2. Press the AUDIBLE SIGNAL button and hold down for
in the audible signal
approx. 5 seconds.
which reminds you that
A brief signal sounds several times. The AUDIBLE SIGNAL
the programme is comdisplay flashes several times.
plete.
The setting is permanently programmed.
The setting is cancelled as described under 1 and 2.
Adjust “level of dryness”
detection:
If the laundry is slightly
drier or slightly damper
at the end of the programme than with the
standard setting.
1. Turn the programme selector to any programme.
2. Press the AUDIBLE SIGNAL and SENSITIVE buttons at the
same time and hold down for approx. 5 seconds.
The current setting appears on the multi-display:
– C0: Setting for drier laundry
– C1: Standard setting
– C2: Setting for damper laundry
3. Press the START/PAUSE button until the setting required
appears on the multi-display.
4. Turn the programme selector to OFF.
The setting is permanently programmed.
To deactivate the EMPTY
WATER display when using an external drain for
the condensed water.
1. Turn the programme selector to any programme.
2. Press the DOOR and SPECIAL CARE buttons at the same
time and hold down for approx. 5 seconds. The multidisplay briefly displays ”0”
The EMPTY WATER display is permanently deactivated.
The setting is cancelled as described under 1 and 2; the
multi-display however briefly displays ”1” (rather than
”0”).
23
Technical data
5
This appliance conforms with the following EU Directives:
– 73/23/EEC dated 19.02.1973 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending
Directive 92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
Height x width x depth
85 x 60 x 60 cm
Depth with loading door open
109 cm
Height can be adjusted by
1.5 cm
Weight when empty
approx. 42kg
Loading volume (depends on programme) 1)
max. 6kg
Energy consumption in accordance with IEC 1121 s. e.
(6kg of cotton, pre-drained at 1000 rpm,
3,36kWh
COTTONS STORAGE DRY programme)
Use
Domestic
permissible ambient temperature
+ 5°C to + 35°C
1) Different loading volume data may be needed in some countries as a result of different measuring methods.
Consumption values
The consumption values have been established under standard conditions. They may deviate when the machine is operated in domestic circumstances.
Programme
COTTONS STORAGE DRY 1)
COTTONS HAND IRON
1)
EASY CARES STORAGE DRY
1) pre-drained at 1000 rpm
2) pre-drained at 1200 rpm
24
2)
Loading volume
in kg
Energy
consumption
in kWh
6
3,36
6
2,70
3
1,20
Installation and connection instructions
1 Installation safety instructions
• Before first starting up, all parts of the transport safety equipment
must be removed. The machine may otherwise be damaged.
• Before starting up for the first time, ensure that the nominal voltage
and type of current specified on the machine type plate match the
nominal voltage and type of current at the installation site. The electrical fuses required can also be found on the type plate.
• Always connect the plug into a protection contact socket which has
been installed as specified.
• With permanent connections: A permanent connection may only be
established by an authorised specialist electrician.
• Do not install machine in rooms at risk of frost.
• Ensure that the door of the machine cannot be blocked by interior
doors of the house or the doors of other appliances.
• Do not install on carpets with high piles. Air circulation will be hindered at the ventilation slots.
• Ensure that the machine is not placed on its mains cable.
• Install the machine horizontally.
Removing transport safety equipment
1 Caution! Before first starting up,
all parts of the transport safety
equipment must be removed.
1. Open loading door
2. Pull off adhesive strips from inside
machine on top of drum.
3. Remove foil hose and polystyrene
padding from the machine.
25
Electrical connection
Details on mains voltage, type of current and the fuses required should
be taken from the type plate. The type plate is fitted near the loading
aperture (see “Machine description” section).
Important:
The plug must be accessible after the appliance has been installed.
Changing door stop
1
Warning! The door stop may only be changed by a specialist.
If necessary, please contact our after-sales service or your specialist
dealer.
Warning! Before changing the door stop, disconnect the mains plug;
with a permanent connection: fully unscrew or deactivate the fuse.
1. Open loading door.
2. Unscrew hinge A from the front of
the machine and take off the loading door.
3. Remove cover plates B and C. To do
this, insert a thin screwdriver into
the slots as shown in the illustration, press downwards slightly and
pry out the cover plates.
4. Use an appropriate tool and exert
pressure to unfasten locking block D
from the snap-on fixture, take out
and reinsert on the other side having rotated the block through 180°.
5. Unscrew hinge A from the loading
door, rotate through 180°, reinsert
on the opposite side and screw
down.
6. Reinsert cover plates B and C on the opposite site having first rotated
them through 180°.
26
7. Unscrew cover plates E from the
front of the machine, rotate
through 180°, screw on the
opposite side.
8. Unscrew door lock F, push down
slightly and remove from the front
of the machine.
9. Disconnect cable connector from
door lock F.
10. Press snap-in button G in and
down, press cover down slightly
and remove from front of the machine.
11. Disconnect cable connector from
cover G.
12. Change door lock F over to the opposite side, insert the cable connector and screw down the door
interlock.
13. On the other side, insert the cable connector in cover G, insert cover
and allow snap-in button to lock into place.
14. Insert loading door and hinges into recesses on the front of the machine and screw down.
15. Once the door stop has been replaced, check the function of the DOOR
button.
Note regarding contact protection: The machine is only secure for
operations again once all plastic parts have been inserted.
27
Special accessories
The following special accessories are available from your Service Force
Centre or your specialist dealer:
Intermediate installation kits for stacked washer and
dryer:
These intermediate installation kits can be used to arrange the dryer
and an automatic AEG-Electrolux washing machine (60cm wide, front
loading) as a space-saving washer/dryer stack. The automatic washing
machine is at the bottom and the dryer is at the top.
Two versions can be supplied:
– without stacker plate
916 018 902
– with extractable stacker plate
916 018 903
Installation kit for external condensate drain
Installation kit (125 122 510) for direct draining of condensate into a
basin, siphon, gully, etc. The condensate tank then no longer has to be
drained, it must however remain in its intended position in the machine. Refer to the “Programme options” section for how to deactivate
the EMPTY WATER display.
Max. displacement height: 1m from the base of the dryer; max. displacement length: 3m
28
Guarantee/Customer Service
Weitere Kundendienststellen im Ausland
In diesen Ländern gelten die Garantiebedingungen der örtlichen Partner. Diese können dort eingesehen werden.
Further after-sales service agencies overseas
In these countries our AEG-Electrolux agents’ own guarantee conditions are applicable. Please obtain further details direct.
Autres agences étrangères assurant le service après-vente
Dans ces pays, les conditions de garantie des concessionnaires de la région sont valables. Vous pouvez les consulter sur place.
Otros puntos de Postventa en el extranjero
En estos países rigen las condiciones de nuestros representantes locales.
las cuales pueden ser consultadas allí mismo.
Ulteriori uffici del servizio tecnico assistenza clienti all’estero
In questi paesi sono valide le condizioni di garanzia dei partner locali.
Queste condizioni possono essere esaminante sul luogo.
Serviços de assistência técnica no estrangeiro
Nestes países são válidas as condições de garantia dos concessionários
locais, podendo aí ser consultadas.
További vevöszolgálati irodák külföldön
Ezekben az országokban a mi AEG-Electrolux vevöszolgálatainknál
saját jótállási feltételek alkalmazhatók. A további adatokat kérjük
közvetlenül szerezzék be.
Servisne službe
Na garancijskem listu boste našli seznam pooblašèenih servisnih
služb AEG-Electrolux.
U.A.E. Abu Dhabi
Universal Trading Company
P.O. Box 43 99
Tel.: 6335331
Service Center 6733974
Jordan
Jordan Household
Supply Co. Ltd.
P.O. Box 3/68
Amman/Tel.: 69 70 50
Malta
ITC
International Trading Company
White House Building
Mountbatte Street
Blata L-Bajda/Tel.: 220644
Egypt
Middle East Commercial
Center
4 Salah El Dein St. - 2nd floor
Heliopolis, Kairo
Egypt
Tel.: 2024181719
Canada
EURO-LINE Appliances
2150 Winston PARK Drive 20
Oakville, Ontario L6H 5V1
Tel.: 905 829 3980
Fax: 905 829 3985
Mauritius
Happy World Centre Ltd.
P.O. 7 54
1 Chausee Street
Port Louis
Tel.: 25355
Australia
The Andi-Co Group
1 Stamford Road
Oakleigh VIC 3166
Tel.: (03) 9569 1255
Fax: (03) 9569 1450
www.andico.com.au
Korea (South)
Core Incorp.
3/F Chewoo Bldg.
200 Nonhyun-Dong
Kangnam-Ku 135-010
Seoul
Telefon 82 2 549 89 61
Namibia
AEG NAMIBIA (PTY)
LIMITED-Jeppe Street
Northern Industrial Area
Windhoek
Tel.: (061) 21-6082/4
Fax: (061) 217838
29
30
Bahrain/Arabian Gulf
A.A. Zayani & Sons
P.O. Box 9 32
Bahrain
Tel.: 17311124
Croatia
Electrolux D.O.O.
Suplova 7
10000 Zagreb
Tel.: 1 61 19512
Fax: 1 61 19513
New Zealand
Monaco Corporation Ltd.
10 Rothwell Avenue
Albany - Auckland
4399 Auckland 1
New Zealand
Tel.: 00 64-92 59 11 11
Fax: 00 64-92 59 11 12
Bulgaria
Electrolux Bulgaria E.O.O.D.
91 Levski Blvd.
1000 Sofia
Tel.: 2 806676
Fax. 2 980 5276
Kuwait/Arabian Gulf
Ali Al-Ghanim Est.
P.O. Box 21540 - Safat
Tel.: 4822190
Fax: 4820116
Syria
WATTAR CO.
P.O. Box 36109
Mazzeh - Damascus
Direct Phone: 00963116132649
Fax: 00963116119537
Cyprus
Hadjikyrlakos & Sons Ltd.
Prodromou 121
P.O. Box 21587
Nicosia 1511
Service Telephones:
Nicosia 02 481226
Limassol 05 562182
Larnaca 04 633929
Paphos 06 932 699
Lebanon
Adib & Assaferi
P.O. Box 539
Tripoli
Iran
ARIAN International Development Co.
AEG Showroom
Shariati, Balatar as Safar
Teheran / Iran
Phone No. Showroom:
021 / 285 513 / 4
Phone No. Service:
021 / 312 27 67 / 8
Estonia
Electrolux Estonia Ltd.
Mustamäe tee 24
EE0006 Tallinn
Tel.: (372) 6 650 090
Fax: (372) 6 650 092
Latvia
Electrolux Latvija Ltd.
Kr.Barona iela 130/2
Riga, LV-1012
Tel.: 371 7313626
Fax: 371 7845954
Poland
Electrolux Poland Sp. zo.o.
ul. Domaniewska 41
02-034 Warszawa
tel.: 022 874 33 33
fax: 022 874 33 00
Hong Kong
Dah Chong Hong Ltd.
20 Kai Cheung Road
Kowloon Bay
Kowloon - Hong Kong
Tel.: 0085222621620
Fax: 0085227550333
Lithuania
Electrolux Lithuania
Verkui 29
2600 Vilnus
Tel.: 372 272 3326
Fax: 372 272 3366
Russia
Electrolux Russia Ltd.
16 Olympiysky prospekt
129090 Moscow
Tel.: (095) 937 7837
Fax: (095) 926 5513
Israel
Evis Ltd.
Tadiran-Ampa Service
10 Gibonay Israel Street
New Industrial Zone
Netanya, 42504
Israel
Malaysia
Arzbergh Engineering
No. 49A/B, Jalan Petaling
Utama 7
4600 Petaling Jaya
Tel.: 3 795 1084
Fax: 3 795 1082
Saudi Arabia
Awad Badi Nahas Est
Shara Siteen
Jeddah 21463
Phone: 6646583
Alia Trading Co
Mecca Road
Riyadh 11491
Phone 4645977
Japan
Electrolux Japan Ltd.
Domestic Appliances
Department
Maruzen Showa Warehouse
Building
Tookai 4-5-12, Ota-ku
143-006 Tokyo
Tel.: 0120-13-7117
Fax: 03-3790-5257
Singapore
Group Pte Ltd.
833 Bukit Timah Road
Unit no. 01-11 Royalville
279887 Singapore
Tel.: 0065 64638484
Fax: 0065 64638488
Slovenia
Electrolux Slovenia D.O.O.
Traska Ul. 132
1000 Ljubljana
Tel.: 61 1234 137
Fax: 61 1234 238
Thailand
Olympia Thai Tower, 444
Rachadapiser Road
Samsennok- Huaykwang
10320 Bangkok
Thailand
Tel.: 006625136111
Fax: 006625136334
Slovakia Rep.
Electrolux Slovakia S.R.O.
Seberiniho 1
821 03 Bratislava
Tel.: 02 4333 4322, 4355
Fax: 02 4333 6976
Hungary
Electrolux Lehel KFT
Erzsébet Királyné útja 87.
1142 Budapest
Tel.: 00361/467-3200
Czech Rep.
South Africa
AEG (Pty) Ltd.
55, 12th Road
P.O. Box 1 02 64
Kew/Johannesburg 2000
Tel.: 8069111
ELECTROLUX DOMÁCå
SPOTØEBIÈE CZ
DIVIZE ELECTROLUX S.R.O.
Customer Centre
Hanusova ul.
140 21 Praha 4
Tel.: 2 6112 6112
Telefax: 2 6112 3504
Service
In the event of technical faults, please first check whether you can
remedy the problem yourself with the help of the operating instructions (section “What to do if…”).
If you were not able to remedy the problem yourself, please contact the
Customer Care Department or one of our service partners.
In order to be able to assist you
quickly, we require the following
information:
– Model description
– Product number (PNC)
– Serial number (S No.)
(for numbers see rating plate)
– Type of fault
– Any error messages displayed by
the appliance
So that you have the necessary reference numbers from your appliance
at hand, we recommend that you write them in here:
Model description:
.....................................
PNC:
.....................................
S No:
.....................................
31
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more
than 150 countries around the world.
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg-electrolux.de
© Copyright by AEG
822 944 843-01-250406-02
Subject to change without notice
Download PDF

advertising