Electrolux | EDC5310 | User manual | Electrolux EDC5310 User Manual

Electrolux EDC5310 User Manual
125992312 gb.qxp
2004-07-03
15:59
Page 2
Dear customer,
Please read these operating instructions carefully and pay particular attention to the safety notes indicated in
the first pages.
We recommend that you keep this instruction booklet for future reference and pass it on to any future owners.
Transport damages
After unpacking the machine please check it is not damaged. If in doubt, do not start it but contact your local
Service Centre.
The symbols you will see on some paragraphs of this booklet have the following meaning:
The warning triangle emphasize information that is particularly important for your safety or correct
functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use of
the appliance.
Tips and information about economical and ecological use of the machine are marked with this symbol.
Our contribution to the protection of the
environment: we use recycled paper.
Contents
Important safety information ......................3
Use ........................................................................7
Disposal ..............................................................3
• The control panel ..............................................7-8
• Programme chart ..................................................9
Tips for environmental protection ............4
• Operating sequence............................................10
• Useful hints ........................................................11
Technical specifications ................................4
Maintenance and Cleaning ........................12
Description of the appliance ......................4
• External cleaning ................................................12
Adjusting the level of conductivity ............5
• Cleaning the door ..............................................12
Installation ..........................................................6
• Cleaning the filters ..............................................12
• Cleaning the condenser unit ..............................12
• Unpacking ............................................................6
• Emptying the water reservoir ..............................13
• Positioning ............................................................6
• Cleaning the air intake grille................................13
• Electrical connection ............................................6
• Cleaning the drum ..............................................13
• Stacking kit ..........................................................6
• Door reversal ........................................................6
Something not working? ............................14
2
125992312 gb.qxp
2004-07-03
15:59
Page 3
These warnings have been provided in the interest of safety. You MUST read them carefully before installing or
using the appliance.
Installation
General safety
• Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
• It is dangerous to alter the specifications or
attempt to modify this product in any way.
• Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Service Centre.
Always insist on genuine spare parts.
• Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
• If the machine is situated on a carpeted floor,
please adjust the feet in order to allow air to
circulate freely.
Child safety
Use
• Children are often not aware of how dangerous
electrical appliances can be. When the machine is
working, children should be carefully supervised
and not be allowed to play with the appliance.
• This appliance is designed for domestic use only.
If the machine is used for any other purposes or is
not used correctly, the manufacturer accepts no
responsibility for any damage that might occur.
• The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children danger of suffocation! Keep them out of children’s
reach.
• Always unplug the appliance after use.
• Clothes which are dripping wet should not be
placed in the dryer.
• Make sure that children or pets do not climb into
the drum.
• Danger of explosion: Never tumble dry items that
have been in contact with inflammable solvents
(petrol, methylated spirits, dry cleaning fluid and
the like). As these substances are volatile, they
could cause an explosion. Tumble dry only items
washed with water.
• When the appliance is to be scrapped, cut off the
electrical supply cable and destroy the plug with
the remaining cable. Disable the door catch in
order to prevent children from becoming trapped
inside while playing.
• Please make sure that no gas lighters have
accidentally been left in pockets of garments to be
loaded into appliance.
Disposal
• Do not dry canvas shoes or sports shoes, as they
could get stuck between the door and the drum,
thus blocking this latter.
• Packaging materials
• Leave the door slightly ajar when the appliance is
not being used. This will allow the seal to be
preserved.
The materials marked with the symbol
recyclable.
are
This means that they can be recycled by disposing
of them properly in appropriate collection
containers.
• Clean fluff filters after using the tumble dryer. To
prevent fire risks, do not use the appliance if the
fluff filters are damaged or without filters.
• Do not allow fluff to accumulate around the dryer.
• Machine
Use authorised disposal sites for your old appliance.
Help to keep your country tidy!
3
ENGLISH
Important safety information
125992312 gb.qxp
2004-07-03
15:59
Page 4
Tips for environmental protection
• To utilize the maximum load, laundry which is to
be dried ready to put away (store dry) can be dried
together with items to be ironed. To do this, select
the programme for iron-dry, remove the iron-dry
items at the end of the programme and then
finish-dry the rest of the load.
To save energy and to help protect the environment,
we recommend that you follow these hints:
• Try to load the maximum capacity of the machine
as small loads are uneconomical.
• Always load well spun laundry. The higher the spin
speed, the lower the electricity consumption and
the shorter the drying times.
• Clean the filters regularly to avoid excessive drying
times and high electricity consumption.
• Do not over-dry laundry, this avoids creasing and
saves energy.
Select the drying programme according to the
type of laundry and the required degree of
dryness.
• Ventilate the room well. The room temperature
should not exceed +35°C during drying.
Technical specifications
DIMENSIONS:
Height
Width
Depth
85 cm
60 cm
58 cm
ELECTRICAL CONNECTION:
MAX. POWER ABSORBED:
MIN. FUSE RATING:
220/230 V/50 Hz
2400 W
16 A
MAX. DRYING CAPACITY:
Cotton, linen
Synthetics
5 kg
2.5 kg
CONSUMPTION:
Cotton, linen
Cotton, linen
Synthetics
3.64 kWh (5.5 kg store dry)
3.64 kWh (5.5 kg iron dry)
1.40 kWh (2.5 kg store dry)
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
Description of the appliance
EDC 5310
A
0
L
B
30’
D
C
60’ 90’
E
F
01 Control panel
G
30’-
G
H
J
K
H
3h
L
2
3
02 Water reservoir
03 Fluff filters
04 Rating Plate
05 Condenser Unit
4
06 Adjustable feet
3
6
5
4
1
J
6h
A
B
C
D
E
F
K
9h
60’- 90’
125992312 gb.qxp
2004-07-03
15:59
Page 5
Water contains, a variable quantity of limestone and
mineral salts of which quantities vary according to
geographical locations thus varying its conductivity
values.
Adjusting the level of conductivity:
Press the START/PAUSE
button sequentially:
the level of conductivity is indicated by the phase
pilot lights, which light in various combinations as
follows:
Relevant variations of the conductivity of the water
compared to those prefixed by the factory could
slightly influence the residual humidity of the laundry
at the end of the cycle.
LED lit
Your dryer allows you to regulate the sensitivity of
the drying sensor based on conductivity values of
the water by using the following procedure.
To access adjustment mode:
Turn the programme selector dial to switch on the
appliance. In selection mode, press simultaneously
the buttons 2 and 4.
Press the buttons down until the pilot lights above
each ones begin to flash and one of the pilot lights
indicating the drying phase lights
, cooling
, or
end cycle
remains lit.
Conductivity
Approximate value
µS/cm
Low
< 300
Medium
300 - 600
High
> 600
Normally, the appliance is factory-set to the highest
level; however, certain models may be configured
differently.
Memorizing the new setting:
Simultaneously press the buttons 2 and 4.
Press the buttons down until the pilot lights above
each ones stop flashing and the buzzer sounds.
EDC 5310
0
C
60’ 90
’
E
30’
D
L
B
A
K
J
H
G
F
1 2 3 4 5
5
ENGLISH
Adjusting the level of conductivity
125992312 gb.qxp
2004-07-03
15:59
Page 6
Installation
Warning!
When operating the tumble dryer, the room
temperature must not be lower than +5°C and
higher than +35°C, as it may affect the performance
of the appliance.
Unpacking
Slide out the polythene bag with the
polystyrene stuffing before using the
appliance.
Electrical connection
This machine is designed to operate on a 220-230 V,
single-phase, 50 Hz supply.
Check that your domestic electrical installation can
take the maximum load required (2.4 kW), also
taking into account any other appliances in use.
Connect the machine to an earthed socket, in
accordance with current wiring regulations.
The manufacturer declines any
responsibility for damage or injury
through failure to comply with the
above safety precaution.
Should the appliance power supply
cable need to be replaced, this must
be carried out by our Service
Centre.
P1106
Should the appliance be moved, it must be
transported vertically.
Important!
Positioning
The power supply cable must be accessible after
installing the machine.
It is recommended that, for your convenience, the
machine is positioned close to your washing
machine.
The tumble dryer must be installed in a clean place,
where dirt does not build up.
Stacking kit
A special stacking kit is available through your
dealer, to enable the mounting of the dryer on top of
a front loading washing machine with cover’s depth
between 48 and 60 cm.
Read carefully the instructions supplied with the kit.
Air must be able to circulate freely all round the
appliance. Do not obstruct the front ventilation grille
or the air intake grille at the back of the machine.
To keep vibration and noise to a minimum when the
dryer is in use, it should be placed on a firm, level
surface.
Once in its permanent operating position, check
that the dryer is absolutely level with the aid of a
spirit level. If it is not, raise or lower the feet until
it is.
The feet must never be removed.
P1148
Do not restrict the floor clearance through deeppile carpets, strips of wood or similar. This might
cause heat build-up which would interfere with
the operation of the appliance.
Door reversal
To make it easier to load or unload the laundry the
door can be reversed.
This operation must be carried out by qualified
personnel.
Please contact the nearest Service Centre.
Important
The hot air emitted by the tumble dryer can reach
temperatures of up to 60°C. The appliance must
therefore not be installed on floors which are not
resistant to high temperatures.
6
125992312 gb.qxp
2004-07-03
15:59
Page 7
The control panel
EDC 5310
L
B
30’- 60’- 90’
60’ 90
’
E
3h
D
6h
C
9h
30’
G
H
J
K
0
L
A
B
C
D
E
F
A
H
G
F
1 Programme guide
J
2 3 4 5 6 7
K
1
8
4 Low temperature button
This will help you to select the correct programme
for drying.
Pressing this button allows drying to be performed
at a lower temperature, for delicate items.
The corresponding pilot light comes on.
This option can also be used for time controlled
drying.
This function cannot be used with QUICK DRYING.
2 Quick drying button
By depressing this button the drying time is reduced
in the following COTTON programmes:
• extra dry
• ready to wear
• store dry
The corresponding light illuminates. This option
cannot be selected together with “low temperature”
function .
5 DELAYED START button
This button allows you to delay the starting of the
programme by 3, 6 or 9 hours.
Press the button until the light relevant to the
desired delay lights up.
This option must be selected after having selected
the programme and before pressing START/PAUSE
to start the programme.
3 Buzzer OFF button
A buzzer sounds
• when selecting the programme
• when depressing the buttons
• when an incorrect option selection is made
• when the programme selector dial is turned to
another position during the programme or when
you depress an option button during the cycle
• at the end of the programme
• when the water reservoir is full
• if the machine is not working correctly
• when the door of the appliance or the small door at
the bottom are open
By depressing button
the acoustic signal is
switched off in the following cases:
• when selecting the programme
• when depressing the buttons
• when the programme selector dial is turned to
another position during the programme or when
you depress an option button during the cycle
• at the end of the programme.
The corresponding light comes on.
The machine begins the countdown, which is shown
by the pilot lights. For example, if you have chosen a
9-hour delay (pilot light 9h lit), after 3 hours, 9h goes
out and 6h lights up; after 3 more hours, 6h goes out
and 3h lights up. When the 9 hours are over (pilot
light 3h off), the drying cycle begins.
During the delayed start period, it is not possible to
change the programme or the selected delay. If you
wish to do so, you must first cancel everything by
rotating the programme selector dial to position “0”.
Select the new programme, the options and the
delayed start, then press START/PAUSE.
If you wish to change only the options, this can be
done on condition that the new option(s) is(are)
compatible with the programme. Set the machine to
PAUSE by depressing the relevant button, select the
new option(s) and depress START/PAUSE button
again.
If you wish to add some laundry while the machine
is performing the countdown, after having done so
and having closed the door, press START/PAUSE
again, in order to allow the machine to complete the
remaining countdown time.
7
ENGLISH
Use
125992312 gb.qxp
2004-07-03
15:59
Page 8
6 Start/Pause button
“Filter cleaning” light
Press this button to start the dryer after having
selected the programme and the options.
The relevant light will stop flashing. If you have
chosen a delayed start, the machine will begin the
countdown.
This light illuminates at the end of the programme to
remind you that the filters must be cleaned.
“Water reservoir full” light
This light comes on at the end of the programme to
remind you that the water reservoir must be emptied
out. If this light illuminates during a programme this
means that the water reservoir is full. The buzzer
sounds, the programme stops, the light of the
Start/Pause button flashes.
If the door of the appliance or the small door at
the bottom is opened while the programme is
running, this button must be pressed again after
closing the door in order to restart the programme
from the point at which it was interrupted.
This button must be depressed also after a power
failure and after having re-inserted the water
reservoir, if it has been emptied in the middle of a
programme after lighting up of light
.
In both cases the light of the Start/Pause button
flashes to remind you that the start button needs to
be pressed again.
“Condenser cleaning” light
It comes on every 80 cycles to remind you that the
condenser must be cleaned.
8 Programme/Time selector dial
7 Indicator lights
Allows you to select electronically controlled or time
controlled drying.
These lights indicate the following functions:
Turn the dial to the required programme or time.
“Drying” light
Electronically controlled drying
(automatic)
This light indicates that the appliance is in the drying
phase.
The appliance runs these programmes with the help
of probes which detect the degree of dampness of
the laundry.
Simply select the programme according to the type
of laundry and degree of drying required.
“Cooling” light
This light indicates that the appliance is in the
cooling phase. At the end of drying, there is a
10 minute cooling phase to cool the laundry.
Time controlled drying
Can be used to finish off drying if necessary.
Select the 90 or 60 minute programme for cottons
or the 30 minute programme for synthetics.
“End of programme” light
This light is on at the end of the cooling phase,
during the anti-creasing phase and at the end of the
programme.
To cancel a programme which is running, turn the
programme selector dial to “0”.
At the end of drying, turn the selector dial to “0” to
switch the machine off before removing the laundry.
8
125992312 gb.qxp
2004-07-03
15:59
Page 9
Programme chart
Degree of drying
required
Type of laundry
Cotton & linen
extra dry
ready to wear
store dry
slightly damp
iron dry
machine iron dry
Synthetics
extra dry
store dry
iron dry
Jumpers
Baby cycle
Jackets, trousers,
dresses, skirts.
Dry fresh
Max-load (1)
Programme
5 kg
5 kg
5 kg
5 kg
5 kg
5 kg
A
B
C(*)
D
E(*)
F
2.5 kg
2.5 kg
2.5 kg
G
H(*)
J
1 kg
(10 jumpers)
K
1 - 4 garments
L
(*) According to CEI 1121 Standards.
• Baby cycle “K” is a special programme for jumpers to be dried “ready to wear”.
• Dry fresh “L” is designed to clean and freshen garments labelled “dry clean only” at home, in your tumble
dryer, using the special product available on the market.
Time controlled drying
Type of laundry
Drying time
Max-load (1)
Programme
selector dial position
Cotton
90 min
5 kg
90’
Cotton
60 min
5 kg
60’
Synthetics
30 min
2.5 kg
30’
(1) Never overfill the drum (do not load large quilts, for example).
Drying times vary according to:
• The type of laundry
• The size of the load
• The degree of spinning prior to drying.
• The requested drying degree.
Fresh & Cool
This position on programme selector dial can be used to freshen the laundry (e.g. to remove a persistent
odour of moth-balls). Programme duration 10 mins.
Load
It is often difficult to estimate the weight of items to be dried. We therefore recommend that you adopt the
following guidelines:
• cotton, linen: drum full but not too tightly packed;
• synthetics: drum no more than half full;
• delicate fabrics: drum no more than one third full.
9
ENGLISH
Automatic drying (electronic programmes)
125992312 gb.qxp
2004-07-03
16:00
Page 10
10. Turn the programme selector dial to “0”; all the
lights go out. The appliance is switched off.
Operating sequence
Remove the laundry.
Before using your tumble dryer for the first time, we
recommend to place a few damp cloths inside the
appliance and dry for 30 minutes.
There may be dust inside a brand new tumble dryer.
If you open and then close the door before
turning the selector dial to “0” all the lights
corresponding to the phases making up the
performed programme come on.
Drying
1. Connect the appliance.
After each use
2. Open the door.
• Clean the filters (see page 12).
• Empty the water reservoir (see page 13).
Important!
If the drying programme has to be stopped before it
reaches the end, we recommend that you turn the
programme selector dial to position
and wait
until the end of this cooling phase before removing
the laundry. This will avoid a build-up of heat inside
the appliance.To do this first turn the dial to “0” and
then to
and depress Start button
.
P1108
P1149
3. Load the items one at a time, shaking them out
loosely.
4. Close the door. Please check the laundry does
not get caught between the door and filter.
Modifying the programme
To change a programme which is running, first
cancel it by turning the programme selector dial to
“0”. Select the new programme and press the Start
button
.
5. Select the drying programme or time. The lights
,
and
come on.
6. If required, press the low temperature button
and/or the buzzer OFF button
or the
QUICK drying button .
7. Select the DELAYED START
if required.
8. Press the Start button
: the corresponding
light stops flashing and drying starts. Only the
light
remains lit. If you have selected the
delayed start, the machine begins its countdown.
If the programme selector dial is turned to
another position, when the machine is running,
the buzzer will sound and the programme phase
indicator lights will flash.
The drum turns alternately in both directions
during drying.
All drying programmes end with a 10 minute
cooling phase (light
is on).
You may remove the laundry after this phase.
The lights
,
buzzer sounds.
and
illuminate and the
9. If the laundry is not removed at the end of the
cycle, the dryer performs an anti-creasing
phase (duration: 30 minutes maximum).
If you do not remove the laundry, the dryer will stop
automatically at the end of the anti-creasing phase.
Lights
,
and
remain lit and the buzzer
sounds for 2 minutes.
10
2004-07-03
16:00
Page 11
Useful hints
• Avoid drying dark clothes with light coloured fluffy
items such as towels as they could attract the
fluff.
• Try to load to the maximum capacity of the
machine as small loads are uneconomical.
For information, here is a list of the average
weights of some common laundry items.
Sheet
700 - 1000 g
Tablecloth
• Easy-care items, too, e.g. shirts, should be
briefly pre-spun before drying (depending on
crease resistance approx. 30 seconds or using the
special brief spin programme of your washing
machine).
400 - 500 g
Kitchen towel
70 - 120 g
Table napkin
50 - 100 g
Towelling hand towel
Bathrobe
• The laundry must be thoroughly spun before
tumble drying.
• Knitted textiles (knitted underwear) may shrink a
little during drying. Please do not overdry items of
this type. It is advisable to allow for shrinkage
when choosing the size of new purchases.
150 - 250 g
• You can also put starched items into your dryer.
However, to achieve the desired starched effect,
choose the programme “iron dry”. To remove any
starch residues, wipe out the internal drum after
drying with a moist cloth and then rub it dry.
1000 - 1500 g
Man’s shirt
200 - 300 g
Pillowcase
100 - 200 g
Man’s pyjamas
400 - 500 g
Ladies’ nightdress
200 - 250 g
• To avoid a static charge when drying is
completed, use either a fabric softener when you
are washing the laundry or a fabric conditioner
specifically for tumble dryers.
• Remove the laundry when the dryer has finished
drying.
• Never tumble dry the following:
Particularly delicate items such as net curtains,
woollen, silk, fabrics with metal trim, nylon tights,
bulky materials such as anoraks, blankets,
eiderdowns, sleeping bags, feather quilts and any
items containing rubber foam or materials similar
to rubber foam.
• If individual items are still damp after drying, set a
brief post-drying time, but at least 30 minutes.
This will be necessary particularly for multilayered
items (e.g. collars, pockets, etc.).
• Always follow the instructions on garment labels:
may be tumble dried
normal drying (high temperature)
delicate drying (low temperature)
do not tumble dry
• Close pillowcases and covers with fasteners to
prevent small laundry items getting tangled inside
them. Close press studs, zips and hooks and tie
belts and apron strings.
• Sort laundry according to type and degree of
drying required.
• Do not over-dry laundry, this avoids creasing and
saves energy.
11
ENGLISH
125992312 gb.qxp
125992312 gb.qxp
2004-07-03
16:00
Page 12
Maintenance and Cleaning
You must disconnect the appliance from the
electricity supply, before you can carry out any
cleaning or maintenance work.
650
800 /
kg 5
kg 2,5
900
70' - 90'
35' - 50'
1000 /
1200
65' - 85'
30' - 45'
800 /
900
80' - 100'
70'
55' -
1000 /
1200
75' - 95'
50' - 65'
kg 2,5
kg 1
50' - 60'
30' - 35'
E
R S
V E
R E
T O
A U
External cleaning
Use only soap and water and then dry thoroughly.
Important: do not use methylated spirit, diluents or
similar products.
P1152
Cleaning the door
Do not use the appliance without filters.
Clean periodically the interior part of the door to
remove any fluff from the seals around the filter.
Accurate cleaning ensures correct drying.
650
800 /
kg 5
kg 2,5
900
70' - 90'
35' - 50'
1000 /
1200
65' - 85'
30' - 45'
800 /
900
80' - 100'
70'
55' -
1000 /
1200
75' - 95'
50' - 65'
kg 2,5
kg 1
50' - 60'
30' - 35'
Cleaning the condenser unit
E
R S
V E
R E
T O
A U
Clean the condenser when light
comes on.
The condenser is situated at the lower part of the
cabinet behind a small door. To open the door,
push the catch as per picture.
P1150
Cleaning the filters
Your dryer will only function well if the filters are
clean.
P1153
During the drying cycle or at the end, it is normal for
water to be present on the surface of the condenser
insertion.
To pull out the condenser, first turn the two red
stops downwards and then remove the condenser
unit holding it at the handle.
The filters collect all the fluff which accumulates
during drying and they must therefore be cleaned
at the end of each programme, before removing
the laundry, with a damp cloth.
The light
is on to remind you this operation.
650
800 /
kg 5
kg 2,5
P1110
900
70' - 90'
35' - 50'
1000 /
1200
65' - 85'
30' - 45'
800 /
900
80' - 100'
70'
55' -
1000 /
1200
75' - 95'
50' - 65'
kg 2,5
kg 1
50' - 60'
30' - 35'
E
R S
V E
R E
T O
A U
P1151
P1154
The filter in the inner door must be removed for
cleaning.
Do not be alarmed by the amount of fluff. It is not
due to excessive wear caused by the dryer. All fabric
loses fluff when drying but it goes un-noticed in the
air. In a tumble dryer it simply collects in the filter.
P1155
Clean it with a brush and rinse it under the shower if
necessary.
After a while, a withish patina due to detergent
residue on laundry forms on the filters. When this
occurs, clean the filters with warm water using a
brush. Remove the filter in the door opening as per
picture (it can be positioned with the tooth facing to
the left or to the right).
P0639
12
2004-07-03
16:00
Page 13
Also clean the outside, removing all fluff.
Cleaning the air intake grille
Clean the rubber seal round the condenser cabinet
and in the inner part of the small door with a damp
cloth.
Using a vacuum cleaner remove the fluff from the air
intake grille at the back of the appliance.
Important! Do not use pointed objects or utensils to
clean the spaces between the plates, as this could
damage the condenser and make it permeable.
Re-fit the condenser, turn the red stops upwards
and close the door.
Do not use this appliance if the condenser
has not been fitted.
P1162
Cleaning the drum
Emptying the water reservoir
When your laundry does not reach the desired
degree of dryness, in other words, when it turns out
either too dry or too damp, we advise you to clean
the inside of the drum with a cloth soaked with
vinegar.
Water extracted from the laundry condenses inside
the machine and is collected in a reservoir.
The reservoir must be emptied after each drying
cycle to ensure efficient operation when the
machine is next used. The pilot light
reminds
you this operation.
This will eliminate the slight patina that has formed
in the drum (due to residues of detergent and
softeners used in the washing, and to the lime
contained in the water), which prevents the probes
from detecting the correct degree of dryness.
Proceed as follows:
• Pull out the reservoir
• Turn it upside down and let water flow down
• Re-fit the reservoir
P1156
P1157
The reservoir must be re-inserted correctly.
If this is not done the pilot light
comes on during
next drying and the programme stops, leaving the
laundry damp. The buzzer will sound.
After emptying and inserting the reservoir the
START-button
has to be depressed again to
allow the programme to continue.
Handy tip: The condensed water may be used in a
steam iron or to top up a battery, etc. In this case it
must be filtered (e.g. through a coffee filter).
13
ENGLISH
125992312 gb.qxp
125992312 gb.qxp
2004-07-03
16:00
Page 14
Something not working?
Before contacting your local Service Centre, please make the following checks:
Important!
If during the drying phase the END pilot light starts blinking and the buzzer sounds, please switch your tumble
dryer off and contact your local Service Centre.
Problem
Possible cause
• The dryer does not work:
• The door(s) is(are) open.
• The plug is not fitted into the wall socket.
• There is no electricity supply from the wall socket.
• The selector dial is not set correctly.
• The water reservoir is full or not correctly inserted
(light
is on). The programme starts in any case
but it stops after approx. 4 minutes.
• The start button
has not been depressed.
• The DELAYED START option has been selected.
• The filters are clogged.
• The dryer does not dry properly:
• The condenser is clogged.
• The water reservoir is full.
• The selected cycle is not suitable for the laundry.
• Insufficient drying time.
• The laundry has not been spun properly.
• The low temperature function
has been
selected.
• Excessive laundry load.
• The dryer is not correctly installed.
This information can be found on the rating plate
(see picture on page 4).
If, after the above checks, there is still a fault, call
your local Service Centre.
Please make sure you give the model and serial
number of the appliance.
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising