Electrolux | EDI97170W | User manual | Electrolux EDI97170W User Manual

user manual
用户手册
Iron AidTM
Iron Aid TM
EDI97170W
2 electrolux
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Important safety information
Environment
Product description
Control panel
What is shown in the display
Before first use
Sorting and preparing laundry
Starting up for the first time
Iron AidTM Steam System
Starting an Iron AidTM programme
2
4
5
6
6
6
7
7
8
12
Drying
Starting a drying programme
Drying rack
Cleaning and maintenance
What to do if ...
Technical data
Machine settings
Hints for test institutes
Installation
Service
14
16
17
18
21
23
23
24
24
27
Subject to change without notice
Important safety information
Important! Only operate the Iron Aid
programmes with distilled water!
Mains water causes damage to the appliance.
Important! In the interest of your safety
and to ensure the correct use, before
installing and first using the appliance,
read this user manual carefully,
including its hints and warnings. To
avoid unnecessary mistakes and
accidents, it is important to ensure that
all people using the appliance are
thoroughly familiar with its operation
and safety features. Save these
instructions and make sure that they
remain with the appliance if it is moved
or sold, so that everyone using it through
its life will be properly informed on
appliance use and safety.
General safety
• It is dangerous to alter the specifications or
attempt to modify this product in any way.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible
for their safety.
• Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
• Any objects such as coins, safety pins,
nails, screws, stones or any other hard,
sharp material can cause extensive damage and must not be placed into the machine.
• In order to avoid danger of fires caused by
excessive drying, do not use appliance to
dry the following items: cushions, quilts
and the like (these items accumulate heat).
• Items such as foam rubber (latex foam),
shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted with foam rubber pads should not be
dried in the tumble dryer.
• Always unplug the appliance after use,
clean and maintenance.
• Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced persons
may cause injury or serious malfunctioning. Contact your local Service Centre. Always insist on genuine spare parts.
• Items that have been soiled with substances such as cooking oil acetone, petrol,
kerosene, spot removers, turpentine, waxes and wax removers should be washed in
hot water with an extra amount of detergent before being dried in the tumble dryer.
electrolux 3
• Danger of explosion: never tumble dry
items that have been in contact with inflammable solvents (petrol, methylated
spirits, dry cleaning fluid and the like). As
these substance are volatile, they could
cause an explosion. Only tumble dry items
washed with water.
• Risk of fire: items that have been spotted
or soaked with vegetable or cooking oil
constitute a fire hazard and should not be
placed in the tumble dryer.
• If you have washed your laundry with stain
remover you must execute an extra rinse
cycle before loading your tumble dryer.
• Please make sure that no gas lighters or
matches have accidentally been left in
pockets of garments to be loaded into appliance
• When removing from the socket, never pull
the mains plug by the cable, instead take
a hold of the plug.
• The height adjustable screw feet must
never be removed.
• Manifold plugs, couplings and extension
cables must not be used. Risk of fire from
overheating!
• Do not spray down the appliance with jets
of water. Risk of electric shock!
• Do not lean on the open door. The appliance may tip over.
• Once the drying cycle or Iron Aid programme has been interrupted, the laundry
and drum may be hot. Risk of burns! Take
care when removing the laundry.
• Take care when interrupting the Iron Aid
programme: Do not open the machine
door during the steam phase. Hot steam
may result in burns. The display shows a
message to indicate the steam phase.
• The final part of a drying cycle occurs without heat (cool down cycle) to ensure that
the items are left at a temperature that ensures that the items will not be damaged.
•
Caution – Hot surface:
Do not touch the back of the appliance
while it is operating.
Warning! Never stop a tumble dry
before the end of the drying cycle
unless all items are quickly removed
and spread out so that the heat is
dissipated. Risk of fire!
• Risk of electric shock! Do not spray
down the appliance with jets of water.
Installation
• This appliance is heavy. Care should be
taken when moving it.
• When unpacking the appliance, check that
it is not damaged. If in doubt, do not use it
and contact the Service Centre.
• All packaging must be removed before
use. Serious damage can occur to the
product and to property if this is not adhered to. See relevant section in the user
manual.
• The final part of a tumble dryer cycle occurs without heat ( cool down cycle ) to
ensure that the items are left at a temperature that ensures that items will not be
damaged.
• Any electrical work required to install this
appliance should be carried out by a qualified electrician or competent person.
• Care must be taken to ensure that the appliance does not stand on the electrical
supply cable.
• If the machine is situated on a carpeted
floor, please adjust the feet in order to allow air to circulate freely under the appliance.
• After having installed the appliance, check
that it is not pressing or standing on its
electrical supply cable.
• If the tumble dryer is placed on top of a
washing machine, it is compulsory to use
the stacking kit (optional accessory).
Use
• The appliance is intended for drying and
steam treatment of standard laundry in domestic applications.
• This appliance is designed for domestic
use. It must not be used for purposes other
than those for which it was designed.
• Only dry fabrics which are designed to be
machine dried. Follow the instructions on
each garment label.
• Do not dry unwashed items in the tumble
dryer.
• Do not overload the appliance. See the
relevant section in the user manual.
• Clothes which are dripping wet should not
be placed in the dryer.
4 electrolux
• Garments which have been in contact with
volatile petroleum products should not be
machine dried. If volatile cleaning fluids are
used, care should be taken to ensure that
the fluid is removed from the garment before placing in the machine.
• When using dry-cleaning sets: only use
those products which are declared as suitable for the dryer by the manufacturer.
• Clean the micro-fine filter and fine strainer
after each drying cycle or Iron Aid programme.
• Do not use the machine without a lint filter
or with a damaged lint filter. Risk of fire!
• Only fill the water reservoir for steam treatment with distilled water. Do not use tap
water or any additives! The condensed
water from this appliance’s condensed
water container can also be used, if it is
filtered first (e. g. with a coffee filter).
• Clean the heat exchanger regularly.
• Never pull the power supply cable to remove the plug from the socket; always
take hold of the plug itself.
• Never use the tumble dryer if the power
supply cable, the control panel, the working surface or the base are damaged so
that the inside of the tumble dryer is accessible.
• With stacked washer and Iron Aid appliance: do not place objects on the appliance. These may fall off during operation.
• The lamp cover for the interior light must
be screwed down tightly.
• Fabric softeners, or similar products
should be used as specified by the fabric
softener instructions.
• Caution - hot surface : Do not touch the
door light cover surface when the light is
switched on.
Child safety
• This machine is not intended for use by
young children or infirm persons without
supervision.
• Children should be supervised to ensure
that they do not play with the appliance.
• The packaging components (e.g. plastic
film, polystyrene) can be dangerous to children - danger of suffocation! Keep them
out of children’s reach.
• Keep all detergents in a safe place out of
children’s reach.
• Make sure that children or pets do not
climb into the drum.
Environment
The symbol
on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Old appliance
Warning!
Remove mains plug from socket when you
have no further use for the machine. Cut off
mains cable and dispose of together with
plug. Destroy loading door hook. Children
cannot then lock themselves in the machine
and put their lives at risk.
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Please dispose of the
packaging materials in the appropriate container at the community waste disposal facilities.
Environmental tips
• In the dryer, laundry becomes fluffy and
soft. Fabric softeners are not therefore
needed when washing.
electrolux 5
• Your dryer will function most economically
if you:
– always keep the ventilation slots on the
base of the dryer unobstructed;
– use the loading volumes specified in the
programme overview;
– ensure you have good ventilation in the
installation room;
– clean the micro-fine filter and fine strainer after each drying cycle;
– spin the laundry well before drying.
Energy consumption depends on spinning speed set in washing machine.
Higher spinning speed - lower energy
consumption.
Product description
1
6
7
8
2
9
10
3
11
4
12
5
13
14
1
2
3
4
5
6
Control panel
Fluff filters
Loading door (reversible)
Ventilation grille
Adjustable feet
Water recirculation valve/filter, Filler neck
for steam water tank
7 Drawer with condensed water container
8
9
10
11
12
13
14
Drum light
Drying rack
Push button for base door opening
Rating Plate
Heat exchanger
Drainage hose for water tank
Heat exchanger door
6 electrolux
Control panel
1
2
3
5
1
2
3
4
4
6
– FILTER
– CONTAINER
5 Function buttons
6 START/PAUSE button
Programme knob and On/Off switch
Display
DELAY TIMER button
Maintenance displays
– HEAT EXCHANGER
What is shown in the display
1
2
3 4 5 6 7
8
9 10 11 12 13 14 15
1
2
3
4
5
6
7
8
LOAD
DRYNESS
Start time preselection
Drying
Iron Aid programme
Cooling
Anticrease
Degree of dryness Display
9
10
11
12
13
14
15
Steam Filter indicator
DELICATE
Child safety device
Steam water tank indicator
BUZZER
Steam display
Start time /programme duration display
Before first use
In order to remove any residues which may
have been produced during production, wipe
the dryer drum with a damp cloth or carry out
a brief drying cycle (30 MIN) with damp cloths
in the machine.
1. Turn the programme knob to
TIME
(TIME).
2. Press the TIME (TIME) button repeatedly
until 0.30 appears in the display.
3. Press the START/PAUSE (START/
PAUSE) button.
electrolux 7
Sorting and preparing laundry
Sorting laundry
• Sort by fabric type:
– Cotton/linen for programmes in
COTTONS programme group.
– Mixed fibres and synthetics for programmes in the
SYNTHETICS programme group.
Drying in the tumble
dryer possible in principle
Dry at normal temperature
Important! Do not place in the appliance any
wet laundry which is not specified on the care
label as being suitable for tumble-drying.
This appliance can be used for all wet laundry
items which are labelled as suitable for tumble-drying.
• Do not dry new, coloured textiles together
with light-coloured laundry items. Textile
colours may bleed.
• Do not dry cotton jersey and knitwear with
the EXTRA programme. Items may shrink!
• Wool and wool-like textiles can be dried
using the
WOOL (WOOL) programme. Before the drying cycle spin the
woollen textiles as well as possible (max.
1200 rpm). Only dry woollen textiles together which are similar or the same with
respect to material, colour and weight.
Please dry heavy laundry items made of
wool separately.
Special notes about Iron Aid
Caution!
• The following textiles cannot be treated
using an Iron Aid programme: woollen
knitwear, leather, textiles with large metal,
wooden or plastic parts, textiles with rusting metal parts, oilskins or wax cotton garments.
• Sorting by care label. The care labels
mean:
Dry at reduced temperature (press DELICATE
(DELICATE) button!)
Drying in the tumble
dryer not possible
• To smooth or freshen laundry with an Iron
Aid programme, sort laundry by size,
weight, material and colour. Only smooth
textiles together that are similar in terms of
size, weight, material and colour.
• Do not dry new, coloured textiles together
with light-coloured laundry items. Colours
may fade (check colour fastness of fabric
when damp in an inconspicuous area).
• Do not use dry cleaning sets such as dryel
in combination with Iron Aid programmes.
Preparing laundry
• To avoid laundry becoming tangled: close
zips, button up duvet covers and tie loose
ties or ribbons (e.g. of aprons).
• Empty pockets. Remove metal items (paper clips, safety pins, etc).
• Turn items with double-layered fabrics inside out (e.g. with cotton-lined anoraks,
the cotton layer should be outermost).
These fabrics will then dry better.
Special notes about Iron Aid
• Before treating garments with an Iron Aid
programme, remove stains by washing or
using localised stain removal.
• Turn items with double-layered fabrics inside out (e.g. with cottonlined anoraks, the
cotton layer should be outermost). These
fabrics will then dry better.
Starting up for the first time
Switching appliance on / switching light on.
Turn the programme selector to any programme. The appliance has been switched
on. When the loading door is opened, the
drum is illuminated. Opening loading door /
loading laundry
1. Open loading door: Push against the
loading door (push point )
8 electrolux
2. Load your laundry (do not force it in/ overload the machine).
Caution! Be careful not to trap laundry
in between the loading door and rubber
seal.
3. Close loading door securely. Lock must
audibly lock.
Iron AidTM Steam System
Fill water tank
You must fill up the water tank before using
an Iron Aid programme for the first time. Use
the distilled water provided if there is not yet
any condensed water from previous drying
programmes (see chapter on "Cleaning and
Maintenance, Emptying condensed water
container"). If, after an Iron Aid programme is
selected, the
water tank indicator on the
display lights up, you will need to fill up the
water tank with distilled water. Otherwise,
you will not be able to start any Iron Aid programme.
Caution! Important! Only fill the water
tank with distilled or fully desalinated
water. Do not use tap water or additives!
You can also use the condensed water
from the tank, as long as you filter it first
(use the canister supplied with the filter
fitted: see figure opposite).
1. Pull drawer containing condensed water
container out a little (1),
1
2. Push down the water tank’s filler neck (1)
and pull out it (2).
1
2
3. Fill with distilled water from the canister
provided, up to the MAX mark inside the
container.
electrolux 9
To activate recirculation set valve to the ON
position. To do that:
1. Pull drawer containing condensed water
container out a little (1). Behind the drawer there is water tank’s filler neck (2).
max
2
4. Push filler neck and drawer with condensed water container back in.
When dry, all textiles not specifically prohibited in the chapter ‘Sorting and preparing
laundry’ may be treated with the Iron Aid
Steam System. Wet textiles may only be treated if they are labelled as suitable for dry programmes.
1
2. Turn the valve to the ON position. Water
will be supplied by the water circuit directly to the steam water tank filling it automatically during the next drying cycle.
Water recirculation system
This system allows you to automatically use
for an Iron Aid Steam cycle the condensed
water collected in the condense water tank
during a drying cycle.
Caution! The water in the condense
water tank will never automatically fill the
steam water tank. The water
recirculation system works only if it is
supplied by water arising during
standard drying cycles.
To activate this system turn the valve to the
ON position. When the valve is ON the steam
water tank will be filled during the next drying
cycle. Water will be supplied by the water
circuit directly to the steam water tank filling
it automatically.
The steam water tank is empty. Please fill it
and then press START/PAUSE (START/
PAUSE)
If valve is closed (OFF position) recirculation system does not work.
10 electrolux
BUZZER (BUZZER)
Additional
functions / options
LOAD (LOAD)
max. load
(weight when dry)
Overview of Iron Aid programmes
COTTON (COTTON)
1.0 kg
•
•
For 1- 6 cotton shirts. Min. 80% natural
fibres (cotton, linen etc).
wet,
dry
SYNTHETICS
(SYNTHETICS)
1.0 kg
•
•
For 1- 6 synthetic shirts. Max. 20% natural fibres (cotton, linen etc).
wet,
dry
COTTON (COTTON)
3.0 kg
•
•
For smoothing cotton garments. Min.
80% natural fibres (cotton, linen etc).
wet,
dry
SYNTHETICS
(SYNTHETICS)
1.5 kg
•
•
For smoothing easy-care garments.
Max. 20% natural fibres (cotton, linen
etc).
wet,
dry
REFRESH (REFRESH )
2.5 kg
•
•
For one suit or up to two suit jackets or
pairs of trousers or similar garments. Also suitable for removing odours. For dry
garments only
Programmes
All information on applications is for
guidance only. Smoothing results
may vary depending on the selected
programme and especially the fittings and material properties of the
textile. The results can be improved
if necessary by using different programmes and steam volumes. For
example, some textiles containing
more than 20% synthetics but with
the right fittings may behave more
like cotton textiles in an Iron Aid programme. You may therefore get better smoothing results by selecting a
cotton Iron Aid programme.
Given the wide range of different
textile grades and properties that
can be manufactured today using
different mechanical and chemical
processes, we recommend running
the first few Iron Aid programmes at
low steam levels and with a small
number of garments that are as similar as possible. Later, you can carefully start to vary the conditions of
Iron Aid programmes to learn from
Application/properties
experience how to get the best results from the volume of laundry loaded, the quality of the textiles and
the most suitable steam levels and
Iron AidTM programmes. Please also
note the accompanying ‘Textile
Guide’.
electrolux 11
Programme
LOAD
Loading volume
MIN
MED
MAX
1 - 2 shirts
COTTON (COTTON)
MIN
MED
MAX
1 - 2 shirts
SYNTHETICS
(SYNTHETICS)
MIN
MED
MAX
0.5 - 1 kg
COTTON (COTTON)
MIN
MED
MAX
0.2 - 0.5 kg
SYNTHETICS
(SYNTHETICS)
MIN
MED
MAX
1 pair of trousers
REFRESH (REFRESH)
3 - 4 shirts
DURATION
dry [min.]1)
DURATION
wet [min.]1)
20-23
41-51
14-17
24-49
13-16
53-64
12-16
43-53
5 - 6 shirts
3 - 4 shirts
5 - 6shirts
1 - 2 kg
2 - 3 kg
0.5 - 1 kg
1 - 1.5 kg
1 jacket
12-16
1 suit
1) exact programme times appear in the display once the machine has performed wet/dry recognition
(approx. 2 min.)
All information provided on selecting the steam level and corresponding load are suggestions only. In
some cases, using a higher steam
level or smaller load may give better
results. The REFRESH(REFRESH)
programme is a gentle Iron Aid programme for nonwashable textiles.
Any distortion to the shape of a garment which might occur in few cases, can be remedied by ironing.
Selecting the programme
Use the programme selector to set the programme you require. The estimated programme duration (in minutes) appears in the
multi-display.
Select steam level
LOAD (LOAD)
To achieve the best results, different steam
levels are required for different volumes of
laundry.
The LOAD button is used to set the required
steam level: MIN, MED or MAX.
All Iron Aid programmes, apart from the
REFRESH programme, automatically recognise the remaining dampness in clothes.
When laundry is wet, a drying cycle is activated first if required.
The table shows the steam levels appropriate
for the selected load, under LOAD.
1. Press the LOAD button repeatedly until
the desired steam level (MIN, MED or
MAX) is shown in the display.
If the LOAD button is not pressed after an
Iron Aid programme is selected, then medium steam level (MED) is selected automatically. If you select the
REFRESH programme, MIN is selected automatically.
12 electrolux
Important: If in doubt, always select a
lower steam level first until you have
more experience with load volumes, fabric types and the corresponding optimum steam level. If too high a steam
level is selected, garments may lose their
shape. If too low a steam level is selected, creases may remain.
Selecting additional functions
The additional functions available for the
Iron Aid programmes are BUZZER (BUZZER), DELAY (DELAY) and the CHILD LOCK.
1. Select the programme and additional
functions.
2. Press the DELAY button as many times
as necessary until the required start delay
appears on the display, e.g.
if the programme is to be started in
12 hours.
3. To activate the delay timer, press the
START/PAUSE button. The amount of
time remaining until the programme is set
to start is continuously displayed (e.g.
,
,
,…
etc).
If the display is showing
and you press the button again, the
time delay will be cancelled. The display
will show
and then the duration of the
selected programme.
BUZZER (BUZZER)
The appliance is supplied with the BUZZER
function activated. When the drying cycle
has finished, an intermittent acoustic signal
will sound. Each time a button is pressed or
a programme is changed using the programme knob, an audible signal is also set to
sound. The button is used to switch the function on or off. When the function is active, the
BUZZER
symbol appears in the display.
DELAY (DELAY)
With the DELAY button, you can delay
the start of a programme by between 30
minutes (
) and a maximum of 20 hours (
).
CHILD LOCK
The child lock can be set to prevent a programme being accidentally started or a programme in operation being accidentally
changed. The child safety device locks all
buttons and the programme knob. The child
safety device can be activated or deactivated
by holding down the BUZZER and TIME buttons simultaneously for 5 seconds.
• Before programme is started: Appliance
cannot be used
• After programme is started: Programme in
operation cannot be changed
The symbol
appears in the display to indicate that the child safety device is activated. The child safety device is not deactivated
once the programme comes to an end. If you
want to set a new programme, you must first
deactivate the child safety device.
Starting an Iron AidTM programme
Press the START/PAUSE button. The programme is started. First, the drying phase indicator appears in the display. The display
will also show the programme duration for
the selected Iron Aid programme, not including the additional drying phase. With wet
laundry, after a few minutes the appliance will
show the correct programme duration for the
Iron Aid programme including the preceding
drying programme. As soon as the right level
of dryness is reached, the Iron Aid programme will start automatically. The steam
indicator shows the progress of the Iron Aid
programme in the display. The individual
steam phases are shown by animated
clouds of steam.
Caution! Important: During the steam
phases that form part of the Iron Aid
programme and also the anti-crease
phase (represented by animated clouds
of steam in the display), the loading door
cannot be opened. Risk of burns!
electrolux 13
If the
water tank indicator lights up when
you select an Iron Aid programme, the programme cannot be started. You will need to
fill the water tank first (see section on ‘Cleaning and maintenance,filling water tank’.)
It is normal for the appliance to make
noises during an Iron Aid or drying programme if garments with hard parts,
such as metal buttons, are put in the
drum.
Changing a programme
To change a programme which has been selected by mistake once the programme has
started, first turn the programme selector to
O OFF and then reset the programme.
The programme can no longer be
changed directly once the programme
has started. If you nevertheless attempt
to change the programme with the programme knob or an additional function
button (except the BUZZER(BUZZER )
button), the START/PAUSE button and
will flash in the display. The drying
programme is not however affected by
this.
Putting in extra items or taking items out before end of programme
1. Open door.
2. Load or remove laundry items.
3. Close door securely.
4. Press the START/PAUSE button to continue the drying cycle.
Iron Aid programme complete /
removing laundry
After the Iron Aid phase has ended,
is illuminated and the icon
AN-
TICREASE appears in the display. If the
BUZZER has been activated, an audible signal sounds at regular intervals.
The Iron Aid programme is automatically
followed by an anti-crease phase, including brief steam phases, which lasts
around 90 minutes.
The drum rotates during the anti-crease
phase. This keeps the laundry loose and free
of creases. It can be removed at any point
during the anti-crease phase, except during
steam phases (look for steam animation in
the display!). Laundry should be removed as
quickly as possible.
1. Open the loading door to remove the
laundry.
2. Before removing the laundry, remove fluff
from the micro-fine filter. It is best to use
a damp hand for this purpose. (See
“Cleaning and maintenance” section.)
3. Remove laundry one garment at a time.
4. Turn the programme knob to O OFF.
Important! After each drying cycle
– Clean the micro-fine filter and fine filter
– Drain the condensed water container
(See section “Cleaning and maintenance”.)
5. Close door.
Caution! To retain the effects of the Iron
Aid treatment, clothes must be removed
one garment at a time during the anticrease phase and hung immediately on
a clothes hanger to dry (for at least 5-15
mins, depending on fabric and selected
steam level). Do up the buttons and tug
the garment into shape, paying particular attention to cuffs and seams.
14 electrolux
Drying
Overview of drying programmes
Application/properties
Care symbols
TIME (TIME)
DRYNESS (DRYNESS)
DELICATE (DELICATE)
Additional
functions /
options
BUZZER (BUZZE)
max. load
(weight when dry)
Programmes
COTTON
EXTRA (EXTRA)
7 kg
•
•
•
-
Thorough drying of thick or multilayered fabrics, e.g.
terry towelling items, bathrobes.
CUPBOARD
(CUPBOARD)
7 kg
•
•
•
-
Thorough drying of fabrics of even thicknesses, e.g.
terry towelling items, knitwear, towels.
DAMP
(DAMP)
7 kg
•
•
•
-
For normal thickness cotton or linen laundry, e.g.
bedding, table linen .
SYNTHETICS
EXTRA (EXTRA)
3 kg
•
•
•
-
Thorough drying of thick or multilayered fabrics, e.g.
pullovers, bedding, table linen.
CUPBOARD
(CUPBOARD)
3 kg
•
•
•
-
For thin fabrics which are not ironed e.g. easy care
shirts, table linen, baby clothes, socks, lingerie with
bones or wires.
DAMP
(DAMP)
3 kg
•
•
•
-
For thin textiles which are still to be ironed, e.g. knitted
1)
items, shirts.
SPECIA L
TIME (TIME)
7 kg
•
•
-
•
For further drying of individual items of laundry or for
small volumes of less than 1kg. You can select a programme duration from 10 mins to 3 hrs in 10-minute
steps.
SILK (SILK)
1 kg
•
a
u
t
o
•
-
Special programme for drying silk using warm air and
gentle movement. .
1)
1)
electrolux 15
WOOL
& SPORT
SHOES(WOOL
& SPORT
SHOES with
RACK)
1 kg
•
a
u
t
o
-
•
Application/properties
Care symbols
TIME (TIME)
DRYNESS (DRYNESS)
DELICATE (DELICATE)
Additional
functions /
options
BUZZER (BUZZE)
max. load
(weight when dry)
Programmes
For drying woollen fabrics after they have been washed, using warm air at minimum mechanical load (Follow section “Sorting and preparing washing”). Recommendation: Remove fabrics immediately after drying, as no anticrease programme follows.
For gentle drying of one pair of sport shoes, washed
and spindried at 1000 rpm.
You can select a programme duration from 30 mins
to 3 hrs in 10-minute steps.
1) Press the DELICATE button.
Selecting the programme
Use the programme selector to set the programme you require. The estimated programme duration (in minutes) appears in the
multi-display.
DRYNESS (DRYNESS)
Selecting additional functions
You can choose from the additional functions
DRYNESS (DRYNESS), DELICATE(DELICATE), BUZZER (BUZZER) and TIME(TIME ),
(if a TIME programme has been selected).
The symbols of the functions available for the
selected programme are shown in the display.
If laundry comes out of the machine too
damp after a standard drying programme,
you can increase the drying result by using
the DRYNESS function. Laundry becomes
drier as you move from MIN to MAX.
1. Press the DRYNESS button repeatedly
until the desired dryness level (MIN, MED
or MAX) is shown in the display. If another
programme has been selected, AUTO
flashes in the display.
If wool or silk comes out of the machine too
damp at the end of a
WOOL or
SILK
programme, you can dry it again by restarting
the appropriate programme, this time with
the DRYNESS function selected and dryness
level MIN, MED or MAX. In the case of a drying cycle with relatively dry laundry, the length
16 electrolux
of the programme cycle displayed at the beginning is corrected after a while.
Caution! Caution: Make sure that by
selecting the DRYNESS function, you do
not over-dry your wool or silk.
DELICATE (DELICATE)
For especially gentle drying of sensitive fabrics with the care label and for temperaturesensitive textiles (e.g. acrylic, viscose). Programme is executed with reduced heat.
DELICATE is only suitable for use with loads
of up to 3kg.
1. Press the DELICATE button. The DELICATE symbol appears in the display.
TIME (TIME)
To select the programme duration after setTIME programme. You can select
ting the
a programme duration from 10 minutes to 3
hours in 10-minute steps. (corresponding to
the
COOLING(COOLING) programme).
1. Turn the programme knob to the
TIMED PROGRAMME. The
minutes is in the display
2. Press the TIME button repeatedly until
the desired programme duration is
shown in the display, e.g.
for a programme of 20 minutes.
If the programme duration is not selected,
the duration is automatically set to 10 mins.
BUZZER(BUZZER)
See chapter "Iron AidTM Steam System" ,
section "Selecting additional functions BUZZER"
DELAY (DELAY)
See chapter "Iron AidTM Steam System" ,
section "Selecting additional functions - DELAY"
CHILD LOCK
See chapter "Iron AidTM Steam System" ,
section "Selecting additional functions CHILD LOCK"
Starting a drying programme
Press the START/PAUSE button. The programme is started. The programme progress
display shows drying progress. The symbols
for
DRYING and
COOLING appear in
the display one after the other. The number
of droplets in the dryness indicator gradually
goes down as the drying process progresses.
Changing a programme
To change a programme which has been selected by mistake once the programme has
started, first turn the programme selector to
O off and then reset the programme.
The programme can no longer be
changed directly once the programme
has started. If you nevertheless attempt
to change the programme with the programme knob or an additional function
button (except the BUZZER(BUZZER)
button), the START/PAUSE (START/
PAUSE) button and
will flash in the
multi-display. The drying programme is
not however affected by this.
Removing laundry or loading laundry
when necessary
Warning! Laundry and drumcan become hot. Risk of burns!
1. Open loading door
2. Load or remove laundry items.
3. Close the door securely. Lock must audibly lock.
4. Press the START/PAUSE (START/
PAUSE) button to continue the drying cycle.
Drying cycle complete / removing
laundry
Once the drying programme has finished,
CREASE GUARD lights up in the display.
BUZZER (BUZZER) is activated, an
If the
audible signal sounds at regular intervals.
The drying cycle is automatically followed by a anti-crease phase which
lasts around 30 minutes.
The drum rotates at intervals during this
phase. This keeps the laundry loose and free
of creases. It can be removed at any time
during the anti-crease phase. (The laundry
should be taken out towards the end of the
anti-crease phase at the latest to prevent
creases from forming.)
1. Open door.
2. Before removing the laundry, remove fluff
from the micro-fine filter. It is best to use
a damp hand for this purpose. (See
“Cleaning and maintenance” section.)
electrolux 17
3. Remove laundry.
4. Turn the programme knob to O off.
5. Important! After each drying cycle
– Clean the micro-fine filter and fine filter
– Drain the condensed water container
(See section “Cleaning and maintenance”.)
6. Close door.
Drying rack
The drying rack offers the possibility of drying
washable woollen fabrics and sports shoes.
The drying rack does not turn with the
clothes-dryer drum. This allows the drying of
woollen garments or sports shoes.
When wet, the wool must be moved as little
as possible because it tends to become matted, so drying rack is a solution.
Sports shoes cannot be dry without rack otherwise can damage the drum due to their
weight.
For first unpacking of the rack please refer to the installation chapter.
Warning! Before installing the rack
check the dryer drum. It must be
empty!
Important! Take out the insoles and place
them beside the shoes on the rack. Tie the
shoelaces.
1. Open the loading door.
2. Insert the rack.
Lift the rack horizontally in the drum.
Guide the rack down until the support
bracket at the front rests on the opening.
3. Place the washing on the rack:
– Spread the garment out in the rack and
roll it up, without squashing or folding
it.
– Place sport shoes on the rack.
4. Select the required programme run time,
selectable with an interval of 10 min, from
30 min. up to 180 minutes.
Press the TIME button as many times as
necessary until the required programme
running time is shown in the display.
5. Press the START/PAUSE button. The
programme is started.
6. At the end of the drying programme open
the loading door and remove the garments or shoes.
7. Turn the programme selector to O OFF.
8. Remove the rack from the drum at the
end of drying.
18 electrolux
Cleaning and maintenance
Cleaning lint filters
To ensure that the appliance works perfectly,
the lint filters in the door and in front of the
drum must be cleaned after every Iron
AidTM or drying cycle.
Caution! Important. Never operate the
dryer without the lint filter or with a
damaged or blocked lint filter.
1. Open loading door
2. Use a damp hand to clean the micro- fine
filter, which is built into the lower part of
the loading aperture.
3. After a period of time, a patina due to detergent residue on laundry forms on the
filters. When this occurs, clean the filters
with warm water using a brush. Remove
the filter from the door pulling it out. It can
be positioned with the tooth facing to the
left or to the right). After cleaning do not
forget to put it back.
Cleaning the water recirculation valve/
filter
If the
STEAM FILTER symbol is shown in
the display, the recirculation filter needs to be
cleaned. The valve/filter is placed behind the
tank handle - see chapter "Product description".
1. Push down the water tank’s filler neck (1)
and pull out it (2).
1
2
2. Clean the valve/filter under warm water.
4. Remove fluff from lint filter, preferably using a damp hand for this purpose.
5. Replace the filter.
electrolux 19
3. Re-insert the valve/filter.
4. Turn the valve/filter in ON position.
Clean the door seal
Wipe the door seal using a damp cloth immediately after the Iron Aid or drying cycle.
Emptying the condensed water
container
Empty condensed water container after every drying cycle. If the condensed water container is full, an active programme will break
off automatically and the
icon display will
light up. In order to continue the programme,
the condensed water container must first be
emptied.
3. Push drainage pipe in and refit condensed water container.
If the programme has been interrupted as
a result of the condensed water container
being full: Press the START/PAUSE button to continue the drying cycle.
The condensed water container has a
volume of approx. 4 litres. This is sufficient for around 7 kg of laundry which
has previously been spun at 1000 revolutions/ minute.
4. The condensed water can be used as
distilled water, e.g. for steam irons. However, first filter the condensed water to
remove any residues and small pieces of
fluff.
Warning! The condensed water is
not suitable for drinking or for
preparing foodstuffs.
1. Pull drawer containing condensed water
container all the way out (1) and pull up
the condensed water container’s drainage pipe as far as it will go (2).
2.
1.
2. Pour out the condensed water into a basin or similar container.
Using the attached canister to filter: Pour
the water out of the container straight
through the filter at the top of the canister.
Cleaning heat exchanger
If the
HEAT EXCHANGER is displayed,
the heat exchanger needs to be cleaned.
20 electrolux
Caution! Operating when the heat
exchanger is blocked with fluff can
damage the dryer. This also increases
energy consumption.
1. Open door.
2. Open door in plinth. To do this, press the
release button on the bottom of the door
aperture and open the door in the plinth
to the left.
6. To empty the heat exchanger, hold vertically over a washing-up bowl.
Caution! Do not use sharp objects to
clean. The heat exchanger could
develop leaks.
7. Clean heat exchanger.
It is best to use a brush or to rinse thoroughly with a hand-held shower.
8. Replace heat exchanger and lock into
place (turn both lock washers outwards
until they snap into place).
9. Close door in plinth.
3. Clean fluff from the inside of the door and
the heat exchanger front chamber. Wipe
the door seal with a damp cloth.
4. Turn both lock washers inwards.
The appliance will not operate if the
HEAT EXCHANGER indicator is still lit.
Caution! Never operate the dryer
without the heat exchanger.
Cleaning the drum
Caution! Do not use abrasives or steel
wool to clean the drum.
5. Use the handle to pull the heat exchanger
out of the base and carry it horizontally to
prevent any remaining water from spilling.
Lime in the water or cleaning agents may
form a barely visible lining on the inside
of the drum. The degree to which the
laundry has been dried is then no longer
detected reliably. The laundry is damper
than expected when removed from the
appliance.
Use a standard domestic cleaner (e.g. vinegar-based cleaner) to wipe down the inside
of the drum and drum ribs.
Clean control panel and housing
Caution! Do not use furniture cleaners
or aggressive cleaning agents to clean
the machine.
Use a damp cloth to wipe down the control
panel and housing.
electrolux 21
What to do if ...
Troubleshooting by yourself
If during operation, the error code E plus
number or letter) appears on the multi-display: Switch the appliance off and on again.
Problem
Dryer does not work.
IronAid programme does
water
not start. the
tank indicator lights up.
After a IronAid programme, garments are
not sufficiently smooth.
Reset programme. Press the START/PAUSE
button. If the error appears again, please
contact the Customer Care Department,
stating the error code
Possible cause
Remedy
Mains plug is not plugged in or fuse Plug in at mains socket. Check fuse
is not working correctly.
in fuse box (domestic installation).
Loading door is open.
Close loading door.
Have you pressed the START/
PAUSE button?
Press the START/PAUSE button
again.
Water tank is empty.
Fill water tank.
Recirculation valve is closed (OFF
position)
Turn the recirculation valve to ON
position.
Wrong programme selected (e.g.
SYNTHETICS instead of
COTTON).
Note the composition of the fabric.
Too low a LOAD level set.
Set a higher LOAD level.
Too many garments in machine, or
garments that are too different.
Load the machine with fewer garments, or only similar ones.
Clothes are not removed until the
anti-crease phase is finished.
Remove clothes quickly one at a
time from the machine as soon as
possible after the start of the anticrease phase.
Garments not hung on clothes
hangers and/or not tugged into
shape.
Hang garments on clothes hangers, do up buttons and tug garments into shape.
Reshape multi-layered garments by
Multi-layered garments tend to lose
ironing after they come out of the
their shape.
machine.
After a IronAid programme, there are no
creases left in the garments.
The IronAid programme has the ef- Iron creases in again after the Ironfect of smoothing garments.
Aid programme.
Drying results unsatisfactory.
Wrong programme selected.
Select a different programme the
next time you dry (see “Programme
overview” chapter).
Lint filters clogged.
Clean lint filters.
Fluff filter clogged.
Clean fluff filter.
Heat exchanger clogged with lint.
Clean heat exchanger.
Overloading of laundry.
Observe recommended loading
volumes.
Ventilation slots in base area covered up.
Uncover ventilation slots in base
area.
Residue on inside surface of drum
or drum ribs.
Clean inside surface of drum and
drum ribs.
22 electrolux
Make an adjustment using the
DRYNESS function (see chapter ”Drying”)
Conductance of water at installation site differs from standard setting of machine.
Re-programme standard setting for
degree of drying (see ‘Programming options’ chapter).
When a button is pressed
- no reaction of the machine.
Drying protection. After the start of
the programme, the option can no
longer be set.
Turn the programme knob to OFF.
Set the programme again.
Drum light does not work.
Programme selector in OFF position.
Turn programme selector to any
programme.
Defective light bulb.
Replace light bulb (see next section).
Displayed programme
time changes erratically or
stays unchanged for a
long time.
Programme time is corrected autoAutomatic process; this is not a
matically depending on type and
machine fault.
volume of laundry and level of
dampness.
Programme inactive,
CONTAINER display illuminated.
Condensed water container is full.
Drying cycle ends shortly
after programme starts.
ANTICREASE display
illuminated.
Select time programme or higher
Not enough washing loaded or
EXTRA instead
washing loaded is too dry for selec- drying level (e.g.
ted programme.
CUPBOARD).
of
Empty Condensed water container , then start programme with
START/PAUSE button.
Drying cycle lasts an unusually long time. Note:
After up to 5 hours the
Lint filter clogged.
drying cycle ends automatically (see ‘End of drying cycle’).
Clean lint filter.
Fluff filter clogged.
Clean fluff filter.
Load volume too big.
Reduce load volume.
Laundry insufficiently spun.
Laundry must be adequately spun.
Particularly high room temperature. Automatic process, there is no fault
Temporary switching off of the
with the appliance. If possible, lowcompressor to avoid overload.
er the room temperature.
Discoloration
Colour fastness of textiles.
Check colour fastness of textiles.
Only treat textiles together if they
are a similar colour.
Changing the bulb for interior lighting
Only use a special bulb which is designed
specially for dryers. The special bulb can be
obtained from your local Service Force centre.
Warning! Do not use standard bulbs!
These develop too much heat and may
damage the machine!
Warning! When the appliance is
switched on, the interior lighting
switches itself off after 4 minutes when
the door is open.
1. Unscrew cover above the bulb (this can
be found directly behind the loading aperture, at the top; refer to “Description of
machine” section.)
2. Replace defective bulb.
3. Screw cover back down.
Warning! Before replacing the bulb,
disconnect the mains plug.
electrolux 23
Check the correct positioning of o-ring gasket before screwing back the door light cover. Do not operate the dryer when missing oring gasket on door light cover.
Warning! For safety reasons, the cover
must be screwed down tightly. If this is
not done, the dryer must not be
operated.
Technical data
This appliance conforms with the following EU Directives:
– 2006/95/EC dated 12.12.2006 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive
92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
Height x width x depth
85 x 60 x 58 cm
Drum volume
108 l
Depth with loading door open
109 cm
Height can be adjusted by
1.5 cm
Weight when empty
Loading volume (depends on
approx. 46 kg
programme)1)
max. 7 kg
Voltage
230V-240V
Required fuse
10A
Total power
2350
Energy efficiency class
B
Energy consumption (7 kg of cotton, predrained
at 1000 rpm) 2)
3,9
Use
Domestic
Permissible ambient temperature
+ 5°C to + 35°C
Consumption values
The consumption values have been established under standard conditions. They may deviate when
the machine is operated in domestic circumstances.
Programme
Energy consumption in kWh
COTTON CUPBOARD 2)
4,0 (7 kg load pre-drained at 800 rpm)
3,9 (7 kg load pre-drained at 1000 rpm)
3,6 (7 kg load pre-drained at 1400 rpm)
COTTON IRON 2)
3.3 (7 kg load pre-drained at 1000 rpm)
SYNTHETICS
CUPBOARD2)
1,3 (7 kg load pre-drained at 1200 rpm)
1) Different loading volume data may be needed in some countries as a result of different measuring
methods.
2) in accordance with EN 61121
Machine settings
Setting
Implementation
24 electrolux
BUZZER permanent off
1. Turn the programme selector to any programme.
2. Press simultaneously the DRYNESS and DELICATE buttons
and hold down for approx. 5 seconds.
3. The buzzer is by default always off. You can use BUZZER button
to activate or deactivate sound but machine does not memorize
your selection.
Water hardness
Water contains, a variable
quantity of limestone and mineral salts of which quantities
vary according to geographical
locations thus varying its conductivity values.
Relevant variations of the conductivity of the water compared
to those prefixed by the factory
could slightly influence the residual humidity of the laundry at
the end of the cycle. Your dryer
allows you to regulate the sensitivity of the drying sensor
based on conductivity values of
the water.
1. Turn the programme selector to any programme.
2. Press simultaneously the DELICATE and START/PAUSE buttons and hold down for approx. 5 seconds. The current setting
is on the display:
–
low conductivity <300 micro S/cm
–
medium conductivity 300-600 micro S/cm
–
high conductivity >600 micro S/cm
3. Press the START/PAUSE button sequentially until you set desired level.
4. To memorize setting press simultaneously the the DELICATE
and START/PAUSE buttons or turn knob to O OFF position
Hints for test institutes
Parameters possible to checked by the Test
Institutes:
• Energy consumption (corrected with final
humidity) during the cupboard dry cotton
cycle with nominal load.
• Energy consumption (corrected with final
humidity) during the cupboard dry cotton
cycle with half load.
• Final humidity (during cupboard dry cotton, iron dry cotton and cupboard dry easy
care)
• Condensation efficiency (corrected with final humidity) during cupboard dry cotton
cycle with nominal and half load
All the cycles have to be checked in accordance with EN 61121 (Tumble dryers for
household use – Methods for measuring the
performance).
Installation
Important! The appliance must be moved in
vertical position for transport.
Appliance positioning
• It is recommended that, for your convenience, the machine is positioned close to
your washing machine.
• The tumble dryer must be installed in a
clean place, where dirt does not build up.
• Air must be able to circulate freely all round
the appliance. Do not obstruct the front
ventilation grille or the air intake grilles at
the back of the machine.
• To keep vibration and noise to a minimum
when the dryer is in use, it should be
placed on a firm, level surface.
• Once in its permanent operating position,
check that the dryer is absolutely level with
the aid of a spirit level. If it is not, raise or
lower the feet until it is.
• The feet must never be removed. Do not
restrict the floor clearance through deeppile carpets, strips of wood or similar. This
might cause heat built-up which would interfere with the operation of the appliance.
Important!
The hot air emitted by the tumble dryer can
reach temperatures of up to 60°C. The appliance must therefore not be installed on
floors which are not resistant to high temperatures.
electrolux 25
When operating the tumble dryer, the room
temperature must not be lower than +5°C
and higher than +35°C, as it may affect the
performance of the appliance.
To unpack the rack:
1. Remove upper protection polystyrene
parts by pulling them.
Important! Should the appliance be moved,
it must be transported vertically.
Important! The appliance must not be
installed behind the lockable door, a sliding
door a door with a hinge on the opposite side
to that of the appliance.
1
1
Removing transport safety packaging
Caution!
Before use all parts of the transport packaging must be removed.
1. Open loading door
2. Pull off adhesive strips from inside machine on top of drum.
2. Lift slightly rack handle (not to the end).
For easiest unpacking turn the rack
upside down
3. Take it carefully out of the drum.
3
3. Remove foil hose and polystyrene padding from the machine.
2
4. Remove from the drum rest of packing
elements.
Electrical connection
Details on mains voltage, type of current and
the fuses required should be taken from the
rating plate. The rating plate is fitted near the
loading aperture (see “Product description”
chapter).
Connect the machine to an earthed socket,
in accordance with current wiring regulations.
Drying rack unpacking
Caution! Before use all packaging parts
and rack must be removed from the
drum
26 electrolux
Warning! The manufacturer declines
any responsibility for damage or
injury through failure to comply with
the above safety precautions.
Should the appliance power supply
cable need to be replaced, this must
be carried out by an authorised service engineer or a qualified electrician. .
The appliance is supplied with a 13 amp plug
fitted. In the event of having to change the
fuse in the plug supplied, a 13 amp ASTA
approved BS 1363/A fuse must be used.
Permanent connection
In the case of permanent connection it is
necessary that you install a double pole
switch between the appliance and the electricity supply (mains), with a minimum gap of
3 mm between the switch contacts and of a
type suitable for the required load in compliance with the current electrical regulations.
The switch must not break the yellow and
green earth cable at any point.
Changing door stop
4
Warning! Before changing the door
stop, disconnect the mains plug.
3
1
Warning! The plug must be
accessible after installing the
machine.
2
The wires in the mains lead are coloured in
accordance with the following code:
1 Blue - Neutral
2 cord clamp
3 Brown - Live
4 Green and Yellow - Earth
The wire coloured green and yellow must be
connected to the terminal marked with the
or colletter «E» or by the earth symbol
oured green and yellow.
The wire coloured blue must be connected
to the terminal «N» or coloured black.
The wire coloured brown must be connected
to the terminal marked «L» or coloured red.
Upon completion there must be no cut, or
stray strands of wire present and the cord
clamp must be secure over the outer sheath.
Warning! A cut off plug inserted into
a 13 amp socket is a serious safety
(shock) hazard.
Ensure that the cut off plug is disposed of safely.
1. Open loading door.
2. Unscrew hinge A from the front of the
machine and take off the loading door.
3. Remove cover plates B . To do this, insert a thin screwdriver into the slots as
shown in the illustration, press downwards slightly and pry out the cover
plates.
A
C
B
D
A
C
4. Use an appropriate tool and exert pressure to unfasten locking block C from the
snap-on fixture, take out and re-insert on
the other side having rotated the block
through 180°.
electrolux 27
5. Unscrew hinge A from the loading door,
rotate through 180°, re-insert on the opposite side and screw down.
6. Re-insert cover plates B on the opposite
site having first rotated them through
180°.
7. Unscrew cover plates D from the front of
the machine, rotate through 180°, screw
on the opposite side.
8. Unscrew door lock E , push down slightly and remove from the front of the machine.
9. Press snap-in button F in and down,
press cover down slightly and remove
from front of the machine.
10. Change door lock E over to the opposite
side, screw down the door interlock.
E
G
F
E
F
11. On the other side, insert cover F and allow snap-in button to lock into place.
12. Insert loading door and hinges into recesses on the front of the machine and
screw down.
Note regarding contact protection: The
machine is only secure for operations again
once all plastic parts have been inserted.
Special accessories
The following special accessories are available from your Electrolux Service Force Centre
or your specialist dealer:
Intermediate installation kits for stacked
washer and iron aid appliance:
These intermediate installation kits can be
used to arrange the iron aid appliance and an
automatic Electrolux washing machine
(60cm wide, front loading) as a space-saving
washer/iron aid stack. The automatic washing machine is at the bottom and the iron aid
appliance is at the top. Two versions can be
supplied:
• without stacker plate
• with extractable stacker plate
Read the manual supplied with the installation kit carefully.
G
Service
In the event of technical faults, please first
check whether you can remedy the problem
yourself with the help of the operating instructions - see chapter What to do if….
If you were not able to remedy the problem
yourself, please contact the Customer Care
Department or one of our service partners.
In order to be able to assist you quickly, we
require the following information:
– Model description
– Product number (PNC)
– Serial number (S No. is on rating plate stuck
to the product - to find it see chapter Product
description ))
– Type of fault
– Any error messages displayed by the appliance
So that you have the necessary reference
numbers from your appliance at hand, we
recommend that you write them in here:
Model description:
28 electrolux
PNC:
S No:
electrolux 29
Electrolux. Thinking of you.
在 www.electrolux.com 上分享更多我们的思维
目录
重要安全信息
环境
产品说明
控制面板
显示屏上显示的内容
首次使用之前
分类和准备衣物
初次开始使用
Iron Aid TM蒸氣系統
開始一個Iron AidTM程序
29
30
31
32
32
33
33
33
34
38
烘干
启动烘干程序
烘干架
清洁和保养
如果发生下列情况应如何...
技术数据
干衣机设置
测试学会的提示
安装
服务
39
41
41
42
45
47
47
48
48
50
如有更改恕不另行通知
重要安全信息
重要事项! 只可使用蒸馏水执行Iron Aid程
序!
排水管的水会导致干衣机损坏。
重要事项! 为了您的安全起见和确保正确使
用,安装和初次使用干衣机之前,请仔细通
读本用户手册,包括其中的提示以及警
告。 为了避免不必要的错误和意外,必须确
保所有使用本干衣机的人员完全清楚其操作
和安全性能。 请妥善保管说明书并在搬迁或
转售干衣机时一并附上说明书,以便使用该
干衣机的所有人都能够正确了解干衣机的使
用和安全信息。
一般安全信息
• 不管以任何方式改变本产品规格或改造本
产品都非常危险。
• 本干衣机不可由肢体伤残、感觉障碍以及
缺乏相关经验和知识的人员(包括儿童)
使用,除非在其安全负责人的看管或指导
下才可使用。
• 确定小动物没有爬入烘干槽内。 为避免发
生此情况,请在使用之前检查烘干槽内
部。
• 任何物体,如硬币、安全别针、钉子、螺
丝钉、石头或任何其他坚硬、尖锐的材料
都会导致重大损害,因此切勿将这些物体
放入干衣机内。
• 为了避免过量烘干导致的火患危险,请不
要使用本干衣机来烘干下列物品: 垫子、
棉被和类似物品(这类物品会累积热)。
• 如泡沫塑料(乳胶泡沫)胶乳泡沫、浴
帽、防水纺织品、胶底物品和衣物或装有
•
•
•
•
•
•
•
•
•
•
•
•
泡沫橡胶的枕头等物品都不应放在滚筒干
衣机内烘干。
使用、清洁和维护之后务必拔下干衣机的
电源插头。
不论在任何情况下都不应该尝试自行维修
干衣机。 没有经验的人员执行维修工作会
导致受伤或严重故障。 请联系您当地的服
务中心。 始终坚持使用原装备件。
被烹饪油丙酮、汽油、煤油、污迹去除
剂、松节油、蜡和蜡去除剂等物质污染的
衣物,应该先用额外数量的洗衣剂在热水
中洗涤,然后才放入滚筒干衣机内烘干。
爆炸危险: 切勿用干衣机来烘干沾有易燃
溶剂(汽油、甲基化酒精、干洗液和类似
物品)的衣物。 因为这些物质是挥发性的
并可导致爆炸。 仅使用干衣机来烘干用水
洗过的衣物。
火灾危险: 被植物油或烹饪油脏污或浸湿
的衣物会导致火灾危险,请不要用干衣机
来烘干这类衣物。
如果您使用污迹去除剂洗涤衣物,必须执
行额外的漂洗程序之后才将衣物放入滚筒
干衣机。
请确定没有将打火机或火柴意外遗留在要
装入干衣机的衣物口袋中。
从电源插座拔下电源线时,不要从电源线
拉出插头,而是握住插头将它拔出。
切勿卸下用于可调高度的螺丝钉。
切勿使用歧管塞、联结器和延伸电缆。 过
热会导致火灾危险!
请勿对干衣机喷水。 触电危险!
请勿依靠在打开的机门上。 干衣机可能会
翻倒。
30 electrolux
• 一旦中断烘干程序或Iron Aid程序,衣物
和烘干槽都可能变热。 灼伤危险! 取出
衣物时请务必小心。
• 中断Iron Aid程序时请务必小心: 请勿在
蒸汽阶段打开机门。 热蒸汽可能会导致灼
伤。 显示屏将会显示一则信息标示蒸汽阶
段。
• 烘干程序的最后部分在没有热的情况下进
行(变凉程序),以确保衣物保持在一个
可保证衣物不会损坏的温度。
•
小心 – 热烫表面:
切勿在干衣机运行时碰触其背面。
警告! 切勿在烘干程序结束之前停止滚
筒干衣机,除非迅速取出有衣物并摊开
使热消散。 火灾危险!
• 触电危险! 请勿对干衣机喷水。
安装
• 本干衣机很重。 搬动时请务必小心。
• 当您拆开干衣机的包装时,请检查并确定
产品没有损坏。 如有疑问,请勿使用干衣
机并联系服务中心。
• 使用干衣机之前,必须拆除所有的包
装。 若不遵循此指示,会导致产品和财产
严重损坏。 请参阅《用户手册》中的相关
部分。
• 滚筒烘干程序的最后部分在没有热的情况
下进行(变凉程序),以确保衣物保持在
一个可保证衣物不会损坏的温度。
• 安装本干衣机所需的任何电气工作都应该
由合格电工或有能力的人员进行。
• 必须小心确保干衣机没有阻碍电源线。
• 如果将干衣机放置在有地毯的地面上,请
调整机脚,使干衣机底下的空气可以自由
流通。
• 安装干衣机后,检查并确保干衣机没有压
住或阻碍电源线。
• 如果将干衣机放置在洗衣机的上面,就必
需使用堆叠套件(可选附件)。
使用
• 本干衣机的设计用途是在家庭应用中烘干
和蒸汽处理标准衣物。
• 此干衣机设计于在家庭中使用。 切勿将本
产品用于设计以外的用途。
• 仅烘干可使用机器烘干的织物。 请遵循衣
物标签上的说明。
• 请勿在滚筒干衣机中烘干未洗涤的衣物。
• 请勿超载干衣机。 请参阅《用户手册》中
的相关部分。
• 请勿将还在滴水的衣物放入干衣机内。
• 请勿将沾有挥发性石油产品的衣物放入机
器内烘干。 如果使用挥发性清洁液,请小
心确保去除衣物上的清洁液才将它放入机
器内。
• 若使用干洗装置: 仅使用制造商标明适合
干衣机的产品。
• 完成每个烘干程序和Iron Aid程序后,清
洁微细过滤器和细微滤网。
• 请勿使用没有安装纤维屑滤网或纤维屑滤
网损坏的机器。 火灾危险!
• 仅在用于蒸汽处理的储水器中注入蒸馏
水。 请勿使用水龙头水或任何添加剂!
如果有预先过滤(例如使用咖啡滤网)干
衣机冷凝水容器的冷凝水则也可使用。
• 定期清洁热交换器。
• 切勿从电源线拉出插座上的插头; 请务必
握住插头。
• 如果电源线、控制面板、工作台面或底座
损坏而可以接触滚筒干衣机的内部,切勿
使用滚筒干衣机。
• 若使用堆叠洗衣机和Iron Aid干衣机: 请
勿在烘干机上放置任何物体。 这些物体会
在运行时掉落。
• 必须用螺丝钉栓紧内部照明的灯罩。
• 使用衣物柔顺剂或类似产品时,必须按照
衣物柔顺剂说明书的指示进行。
• 小心 - 热烫表面 : 打开照明时,请勿碰
触机门灯罩表面。
儿童安全
• 本烘干机不可在没有看管的情况下由儿童
或体弱人士使用。
• 应该看管儿童以确保他们没有玩耍干衣
机。
• 包装部件(例如塑料袋、聚苯乙烯)可能
会对儿童造成危险 - 窒息危险! 请将它们
存放在儿童无法触及的地方。
• 将所有洗洁剂它们存放在儿童无法触及的
安全地方。
• 确定儿童或小动物没有爬入烘干槽内。
环境
产品上或其包装上的标记表示不能把该产品
作为家 庭垃圾般处理。应该将其弃置在电气
和电子设备的废品 回收站点。 为了确保本
品得到正确弃置和避免由于不适当处理废
品 而给环境和人类健康带来潜在的负面效
果,您也可以尽 一分力。 对于本品回收的
更详细信息,请联系您当地的废物回收 部
electrolux 31
门、您的家庭垃圾处理服务点或您产品的商
店。
旧器具
警告!
如果您不要再使用该机器,请从插座拔下电
源插头。 剪断电源线并和插头一起废弃。
销毁装载门钩。 这样儿童就不会将自己锁在
机器内而危及生命。
包装材料
包装材料符合环保并可回收利用。 塑料部件
都使用标记识别,例如 >PE<, >PS< 等。请
将包装材料丢弃在社区废物处理设施的适当
容器内。
• 如果您遵循下列说明进行,您的干衣机将
能够以最经济的方式操作:
– 始终保持干衣机底座上的通风槽通畅无
阻;
– 使用程序概观中指定的装载容量;
– 确保安装室内的通风良好;
– 完成每个烘干程序后,清洁微细过滤器
和细微滤网;
– 烘干之前妥善使衣物脱水。
能源的消耗将取决于洗衣机上设置的脱
水转速。 较高脱水转速 - 较低能源消
耗。
环境提示
• 在干衣机内,衣物会变得蓬松和柔软。 因
此在洗涤时不需要使用衣物柔顺剂。
产品说明
1
6
7
8
2
9
10
3
11
4
12
5
13
14
1 控制面板
2 绒毛滤网
32 electrolux
3
4
5
6
7
8
装载门(可反转)
通风栅
可调机脚
水循环阀/过滤器、蒸汽水槽的过滤器颈
带冷凝水容器的隔间
烘干槽照明
9
10
11
12
13
14
烘干架
用于打开底座门的按钮
铭牌
热交换器
水槽的排水管
热交换器门
控制面板
1
2
3
5
1
2
3
4
4
6
– 过滤器
– 容器
5 功能按钮
6 "开始/暂停"按钮
程序旋钮和开关
显示屏
"延迟计时器"按钮
保养显示
– 热交换器
显示屏上显示的内容
1
2
3 4 5 6 7
8
9 10 11 12 13 14 15
1
2
3
4
5
6
7
8
LOAD(装载量)
DRYNESS(干燥度)
预先选择开始使劲
烘干
Iron Aid程序
冷却
抗皱摺
干燥度显示
9
10
11
12
13
14
15
蒸汽过滤器指示灯
DELICATE(纤细衣物)
儿童安全设备
蒸汽水槽指示灯
BUZZER(蜂鸣器)
蒸汽显示
开始时间/程序持续时间显示
electrolux 33
首次使用之前
为了去除生产时可能产生的任何残余物,可
使用湿布擦拭干衣机的烘干槽,或将湿布放
在干衣机内然后执行简短的烘干程序(30分
钟)。
1. 将程序旋钮转到
TIME(TIME)(时
间)。
2. 重复按TIME(TIME)(时间)直到显示屏
中出现0.30。
3. 按START/PAUSE(START/PAUSE)
(开始/暂停)按钮。
分类和准备衣物
分类衣物
• 按织品类型分类:
– 棉/亚麻布使用程序组内的
COTTONS。
可按照操作原理在滚筒
干衣机内烘干
在正常温度烘干
重要事项! 请勿将护理标签上未指明适合滚
筒烘干的任何湿衣物放入干衣机内。
本干衣机可用于标明适合滚筒烘干的所有湿
衣物。
• 请勿将新的彩色纺织品和浅色衣物一起烘
干。 纺织品的颜色可能会渗透到衣物上。
• 请勿使用EXTRA程序烘干棉质运动衫和针
织品。 衣物可能会收缩!
• 可以使用
WOOL(WOOL)(羊毛)程
序烘干羊毛和类似羊毛的纺织品。 在烘干
程序之前,尽可能使羊毛纺织品脱水(最
大1200 rpm)。 仅将类似或材料、颜色
和重量相同的羊毛纺织品一起烘干。 请个
别烘干羊毛制造的沉重衣物。
关于Iron Aid的特殊注释
小心!
• 下列纺织品不能使用Iron Aid程序处理:
羊毛针织品、皮革、带大型金属、木制过
塑料部件的纺织品、带生锈金属部件、油
布或蜡棉衣物的纺织品。
• 若要使用Iron Aid程序使衣物光鲜柔顺,
可按尺寸、重量、材料和颜色来分类衣
初次开始使用
打开干衣机电源/打开照明。
将程序选择器转到任何程序。 干衣机电源已
经打开。 打开装载门时,烘干槽将会亮
起。 打开装载门/装载衣物
1. 打开装载门: 推向装载门(推点)
– 混合织品及合成纤维使用程序组内的
SYNTHETICS。
• 按护理标签分类: 护理标签将说明:
在降低温度烘干(按
DELICATE(DELICAT
E)[纤细衣物]按钮!)
不 可以在滚筒干衣机内
烘干
物。 仅将类似或尺寸、重量、材料和颜色
相同的衣物一起执行柔顺纺织品操作。
• 请勿将新的彩色纺织品和浅色衣物一起烘
干。 可能会出现褪色现象(在不显眼的地
方浸湿衣物时检查衣物的不褪色性)。
• 请勿将干洗装置(例如干洗剂)和Iron Aid
程序组合使用。
准备衣物
• 若要避免衣物缠结: 将拉链拉上、扣好棉
被的扣,并绑紧松开的结及丝带(例如围
裙)。
• 清空衣物口袋。 取出金属物件(纸夹、安
全别针等)。
• 反转带双层织物的衣物(例如,带棉衬里
的兜帽,棉层应该在最外面)。 这样即可
更好的烘干这类织物。
关于Iron Aid的特殊注释
• 使用Iron Aid程序处理衣物之前,洗涤或
使用局部污迹去除剂来去除污迹。
• 反转带双层织物的衣物(例如,带棉衬里
的兜帽,棉层应该在最外面)。 这样即可
更好的烘干这类织物。
34 electrolux
2. 装载您的衣物(请勿强制挤入衣物/超载
干衣机)。
小心! 小心不要让衣物夹在装载门和橡
胶密封垫之间。
3. 稳固关闭装载门。 必须听到锁定的声
音。
Iron Aid TM蒸氣系統
将水注入水槽中
初次使用Iron Aid程序之前,您必须注满水
槽。 如果尚未从先前的烘干程序中获得任何
冷凝水,可使用提供的蒸馏水(请参阅"清洁
和维护,清空冷凝水容器"章节)。 如果在
选择Iron Aid之后,显示屏上的
水槽指
示灯亮起,您必须在水槽中注入蒸馏水。 否
则,您将无法启动任何Iron Aid程序。
小心! 重要信息! 仅在水槽中注入蒸馏
水或完全脱盐的水。 请勿使用水龙头水
或添加剂! 您也可以使用水槽中的冷凝
水,只要您事先将其过滤(使用所安装
过滤器提供的罐子: 请参阅对页的
图)。
1
2
3. 从提供的罐子注入蒸馏水,直到容器内
的MAX标记。
1. 将包含冷凝水容器的隔间拉出一点(1),
max
1
2. 向下按水槽过滤器颈(1)然后将它拉出
(2)。
4. 将过滤器颈和包含冷凝水容器的隔间推
入原位。
electrolux 35
执行烘干时,在"分类和准备衣物"章节中特
别禁止的所有纺织品都可以使用"Iron Aid蒸
汽系统"处理。 只有标明适合烘干程序的湿
衣物可进行处理。
2. 将阀转到ON位置。 水将会在下一个烘干
程序,由水电路直接供应到自动注入的
蒸汽水槽。
水循环系统
此系统允许您在"Iron Aid蒸汽"程序中,自动
使用烘干程序过程中在冷凝水槽所收集的冷
凝水。
小心! 冷凝水槽中的水将永远不会自动
注入蒸汽水槽。 水循环系统只有在获得
标准烘干程序期间所形成的水供应时操
作。
若要激活此系统,可将阀转到ON位置。 当
阀处于ON位置时,蒸汽水槽将会在下一个
烘干程序填充。 水将会由水电路直接供应到
自动注入的蒸汽水槽。
若要激活循环,可将阀转设置为ON位置。
若要执行此操作:
1. 将包含冷凝水容器的隔间拉出一点(1)。
隔间后面有一个水槽过滤器颈(2)。
蒸汽水槽是空的。 请填充该水槽然后按
START/PAUSE(开始/暂停)。
如果阀关闭(OFF位置),循环系统将
不会操作。
2
1
Iron Aid程序概观
SYNTHETICS(合
成纤维)
COTTON(COTTON)
(棉质)
BUZZER(蜂鸣器)
COTTON(COTTON)
(棉质)
LOAD(装载量)
程序
最大装载量
(烘干时的重量)
附加功能/选项
1.0公
斤
•
•
用于1- 6件棉质衬衫。 最少 80%天然纤
维(棉、亚麻布等)。
1.0公
斤
•
•
用于1- 6件合成纤衬衫。 最多20%天然
纤维(棉、亚麻布等)。
3.0公
斤
•
•
用于柔顺棉质衣物。 最少 80%天然纤
维(棉、亚麻布等)。
应用/性质
湿、
干
湿、
干
湿、
干
36 electrolux
BUZZER(蜂鸣器)
程序
LOAD(装载量)
最大装载量
(烘干时的重量)
附加功能/选项
应用/性质
SYNTHETICS(SYNT
HETICS)(合成纤
维)
1.5公
斤
•
•
用于柔顺免烫衣物。 最多20%天然纤维
(棉、亚麻布等)。
REFRESH
(REFRESH )(光鲜)
2.5公
斤
•
•
用于一套或最多两套夹克或几件长裤或
类似衣物。 也适用于去除气味。 仅适
用于干衣物
关于应用的所有信息仅供指导。 柔顺效
果会根据所选择的程序和特别是纺织品
的装配和材料性质而有所不同。 如有必
要,可使用不同的程序和蒸汽量改进效
果。 例如,一些纺织品包含超过20%合
成纤维但具有正确的装配,在Iron Aid程
序中可能表现得更像棉质纺织品。 因
此,您可以选择棉质Iron Aid程序来获得
更好的柔顺效果。
湿、
干
的情况下,我们建议以低蒸汽水平运行
首几次的Iron Aid程序,以及使用尽可能
类似的小量衣物。 然后,您可以小心开
始改变Iron Aid程序的情况,从经验中学
习如何从装载的衣物量、纺织品的质
量,以及最合适的蒸汽水平和Iron Aid
TM程序获得最佳效果。 请同时注意随附
的《纺织品指南》。
今天,在可以使用不同的机器和化学加
工来制造各种不同的纺织品等级和性质
程序
LOAD
装载量
MIN
MED
MAX
1 - 2件衬衫
MIN
MED
MAX
1 - 2件衬衫
COTTON(棉
质)
MIN
MED
MAX
0.5 - 1公斤
SYNTHETICS
(合成纤维)
MIN
MED
MAX
0.2 - 0.5公斤
MIN
MED
MAX
1条长裤
REFRESH(REFRES
H)(光鲜)
COTTON(棉
质)
SYNTHETICS(SYN
THETICS)(合成纤
维)
3 - 4件衬衫
5 - 6件衬衫
3 - 4件衬衫
5 - 6件衬衫
1 - 2公斤
2 - 3公斤
0.5 - 1公斤
1 - 1.5公斤
1件夹克
1套衣服
干[分钟]1)
持续时间
持续时间
湿[分钟]1)
20-23
41-51
14-17
24-49
13-16
53-64
12-16
43-53
12-16
1) 实际程序时间会在干衣机执行湿/干识别(约2分钟)之后出现在显示屏中 。
关于选择蒸汽水平和相应装载量的所有
信息仅作为建议提供。 在一些情况下,
使用较高蒸汽水平或较小装载量可能会
提供更佳效果。
REFRESH(REFRESH)(光鲜)程序是
用于不可洗纺织品的温和Iron Aid程
electrolux 37
序。 在少数情况下可能发生的衣物变形
可通过熨烫解决。
选择程序
使用程序选择器选择您需要的程序。 估计的
程序持续时间(以分钟显示)将会在多重显
示屏中显示。
选择蒸汽水平
LOAD(装载量)
若要达到最佳效果,必须针对不同的衣物量
使用不同的蒸汽水平。
LOAD按钮用于设置所需的蒸汽水平: MIN,
MED或MAX。
REFRESH程
所有的Iron Aid程序,除了
序,可自动识别衣物剩余的湿度。 如果衣物
潮湿,将会在必要时先激活烘干程序。
下表显示在LOAD下,适用于所选装载量的
蒸汽水平。
1. 重复按LOAD按钮,直到所需的蒸汽水平
(MIN、MED或MAX)出现在显示屏
中。
如果在选择
Iron Aid程序之后没有按
LOAD按钮,将自动选择中等蒸汽水平
REFRESH程序,
(MED)。 如果您选择
将会自动选择MIN。
重要信息: 如果有任何疑惑,可始终先
选择较低的蒸汽水平,直到您比较熟悉
装载量、织品类型和相应的最佳蒸汽水
平为止。 如果选择太高的蒸汽水平,衣
物可能会变形。 如果选择太低的蒸汽水
平,可能会残留油脂。
选择附加功能
Iron Aid程序提供的附加功能包括
BUZZER(BUZZER)(蜂鸣器)、
DELAY(DELAY)(延迟)和CHILD
LOCK"儿童安全防护锁"。
BUZZER(BUZZER)(蜂鸣器)
本干衣机在装运时已启用BUZZER
功
能。 完成烘干程序后,将会发出间歇性的声
音信号。 每次按下某个按钮或使用程序旋钮
更改程序时,也会发出声音信号。 该按钮用
于打开或关闭此功能。 启用此功能时,
BUZZER
符号将会出现在显示屏中。
DELAY (延迟)
利用DELAY按钮,您可以将启动程序的
时间延迟30分钟(
)和最
)之间。
长20小时(
1. 选择程序和附加功能。
2. 根据需要,多次按DELAY按钮直到所需
的启动延迟出现在显示屏中,例如,若
要在12小时内启动程序,则为
。
3. 若要激活延迟计时器,可按START/
PAUSE按钮。 程序启动之前的剩余时间
将会持续显示(例如
、
、
,…
等)。
如果显示屏显示
而且您
再次按下该按钮,时间延迟将会取消。
显示屏将显示
然后是所选程序的持
续时间。
儿童安全防护锁
您可以设置"儿童安全防护锁"来防止程序意
外启动,或执行中的程序意外更改。 儿童安
全设备防护锁可锁定所有按钮和程序选
钮。 要启用或禁用儿童安全设备,可同时按
住BUZZER和TIME按钮5秒。
• 启动程序之前: 无法使用干衣机
• 启动程序之后: 不能更改执行中的程序
38 electrolux
符号将会出现在显示屏中,用于标示已启
用儿童安全设备。 儿童安全设备在程序结束
时将不会禁用。 如果您要设置新的程序,您
必须先禁用儿童安全设备。
開始一個Iron AidTM程序
按START/PAUSE按钮。 程序将会启动。
首先,烘干阶段指示灯将会出现在显示屏
中。 显示屏也将显示所选Iron Aid程序的程
序持续时间,不包括附加的烘干阶段。 如果
要烘干湿衣物,干衣机将会在几分钟后显示
Iron Aid程序的正确程序持续时间,包括之
前的烘干程序。 达到正确的干燥程度之后,
Iron Aid程序将会立即自动启动。 蒸汽指示
灯将会在显示屏中显示Iron Aid程序的进
度。 个别的蒸汽阶段以动画蒸汽云显示。
小心! 重要信息: 在形成Iron Aid程序一
部分的蒸汽阶段和抗皱摺阶段期间(在
显示器中以动画蒸汽运呈现),将无法
打开装载门。 灼伤危险!
水槽指示灯在您选择Iron Aid程序
如果
时亮起,程序将无法启动。 您将需要先填充
水槽(请参阅"清洁和保养,填充水槽"章
节)。
如果将具有金属部件(如金属钮扣)的
衣物放入烘干槽,干衣机在Iron Aid或烘
干程序期间发出噪音是正常的。
更改程序
若要更改错误选择的程序,在程序启动时,
立即先将程序选择器转到 O OFF然后重置程
序。
程序一旦启动,就无法直接更改。 如果
您仍然尝试使用程序旋钮或附加功能按
钮(除了BUZZER[蜂鸣器]按钮)更改
将
程序,START/PAUSE按钮和
会在显示屏中闪烁。 但是,烘干程序将
不会受到此操作的影响。
在程序结束之前放入额外衣物或取出衣物
1. 打开机门。
2. 装载或取出衣物。
3. 稳固关闭机门。
4. 按START/PAUSE按钮继续烘干程序。
Iron Aid程序完成/取出衣物
Iron Aid阶段结束后,
将会
亮起,而
ANTICREASE(抗皱摺)图标
将会在显示屏中显示。 如果启用了
BUZZER,将会以固定间隔发出声音信号。
Iron Aid程序之后将会自动执行抗皱摺阶
段,包括简短的蒸汽阶段,该阶段持续
大约90分钟。
烘干槽将会在抗皱摺阶段旋转。 这样即可使
衣物散开而不会出现皱摺。 您可以在抗皱摺
阶段的任何时刻取出衣物,除了蒸汽阶段
(请查看显示屏中的蒸汽动画!)。 请尽可
能快取出衣物。
1. 打开装载门取出衣物。
2. 取出衣物之前,先从微细过滤器取出绒
毛。 最好是弄湿双手再执行此操作。
(请参阅"清洁和保养"章节。)
3. 一次取出一件衣物。
4. 将程序旋钮转到 O OFF。
重要信息! 在每个烘干程序之后
– 清洁微细过滤器和细微滤网
– 排出冷凝水容器中的水(请参阅"清洁
和保养"章节。)
5. 关闭机门。
小心! 若要保持Iron Aid处理的效果,必
须在抗皱摺阶段一次取出一件衣物,然
后立即挂在衣架上晾干(至少5-15分
钟,根据织品和选择的蒸汽水平而
定)。 将纽扣扣好拖拉衣物成形,特别
注意袖口和接缝。
electrolux 39
烘干
烘干程序概观
应用/性质
护理符号
TIME(时间)
DRYNESS(干燥度)
DELICATE(纤细衣物)
BUZZER(蜂鸣器)
附加功能/选项
最大装载量
(烘干时的重量)
程序
COTTON
EXTRA(EXTR
A)(额外)
CUPBOARD(C
UPBOARD)
(衣橱)
DAMP(DAMP)
(湿)
7公
斤
•
•
•
-
彻底烘干厚或多层织品,例如,厚绒布毛巾物品、浴
衣。
7公
斤
•
•
•
-
彻底烘干更厚的织品,例如,厚绒布毛巾物品、针织
品、毛巾。
7公
斤
•
•
•
-
用于正常厚度的棉或亚麻布制品,例如被褥、桌布。
SYNTHETICS
EXTRA(EXTR
A)(额外)
CUPBOARD(C
UPBOARD)
(衣橱)
DAMP(DAMP)
(湿)
3公
斤
•
•
•
-
彻底烘干厚或多层织品,例如,套头毛衣、被褥、桌
布。
1)
3公
斤
•
•
•
-
用于无需烫熨的薄织品,例如,免烫衬衫、桌布、婴
孩衣服、袜子、带罩杯和铁丝网的女用内衣。
1)
3公
斤
•
•
•
-
用于仍需烫熨的薄织品,例如,编织衣物、衬衫。
1)
SPECIAL(特殊)
TIME(TIME)
(时间)
SILK(SILK)
(丝绸)
7公
斤
•
•
-
•
用于进一步烘干个别衣物或者小量或少于1公斤的衣
物。 您可以选择从10分钟到3小时的程序持续时间,
步幅为10分钟。
1公
斤
•
自
•
动
-
使用热风及温和运动烘干丝绸的特殊程序。 .
40 electrolux
WOOL &
SPORT
SHOES(WOO
L & SPORT
SHOES with
RACK)(使用
架子的羊毛织品
和运动鞋)
1公
斤
•
自
动
•
应用/性质
护理符号
TIME(时间)
DRYNESS(干燥度)
DELICATE(纤细衣物)
BUZZER(蜂鸣器)
附加功能/选项
最大装载量
(烘干时的重量)
程序
在最小机械负荷下使用热风烘干洗涤后的羊毛织品
(请遵循"分类和准备洗涤"章节的说明进行)。 建
议: 烘干后立即取出织品,因为之后不会执行抗皱
摺程序。
用于温和烘干一双运动鞋,在1000 rpm转速下洗涤
和脱水甩干。
您可以选择从30分钟到3小时的程序持续时间,步幅
为10分钟。
1) 按DELICATE按钮。
选择程序
使用程序选择器选择您需要的程序。 估计的
程序持续时间(以分钟显示)将会在多重显
示屏中显示。
选择附加功能
您可以选择下列附加功能DRYNESS(干燥
度)、DELICATE(纤细衣物)、BUZZER
(蜂鸣器)和TIME(时间),(如果选择了
TIME程序)。 所选程序可使用的功能的符
号将会在显示屏中显示。
DRYNESS(干燥度)
如果在标准烘干程序之后从干衣机取出衣物
时太湿,您可以使用DRYNESS(干燥度)
功能来提高烘干效果。 如果您从MIN(最
小)移到MAX(最大),衣物就会变得比较
干燥。
1. 重复按DRYNESS按钮,直到所需的蒸汽
水平(MIN、MED或MAX)出现在显示
屏中。 如果选择另一个程序,AUTO将
会在显示屏中闪烁。
如果在
WOOL或
SILK程序之后从干
衣机取出羊毛织品或丝绸时太湿,您可以尝
试重新启动适当程序再次烘干,但这次同时
选择DRYNESS功能和干燥度MIN、MED或
MAX。 在烘干相当干的衣物的烘干程序
下,开始时显示的程序长度将会在一会儿之
后修正。
小心! 小心: 确定选择DRYNESS功
能,让您不会过度烘干羊毛织品或丝
绸。
DELICATE(纤细衣物)
用于特别温和烘干带有护理标签的敏感织
品,和用于对温度敏感的纺织品(例如,丙
烯酸纤维、纤维胶)。 程序将会在低热下执
行。 DELICATE(纤细衣物)仅适用于最多
3公斤的装载量。
1. 按DELICATE按钮。
DELICATE符号
将会出现在显示屏中。
TIME(时间)
electrolux 41
用于在设置
TIME程序后选择程序持续时
间。 您可以选择从10分钟到3小时的程序持
续时间,步幅为10分钟。 (相应于
COOLING[冷却]程序)。
1. 将程序旋钮转到
(计时程序)。
分钟将会出现在显示屏中。
2. 重复按TIME按钮,直到所需的程序持续
时间出现在显示屏中,例如,20分钟的
程序为
。
如果没有选择程序持续时间,持续时间将会
自动设为10分钟。
BUZZER(蜂鸣器)
请参阅"Iron AidTM蒸汽系统"篇章的"选择附
加功能 - BUZZER"章节。
DELAY (延迟)
请参阅"Iron AidTM蒸汽系统"篇章的"选择附
加功能 - DELAY"章节。
儿童安全防护锁
请参阅"Iron AidTM蒸汽系统"篇章的"选择附
加功能 - 儿童安全防护锁"章节。
启动烘干程序
按"开始/暂停"按钮。 程序将会启动。 程序
进度显示屏将显示烘干进度。 烘干
和冷
却
符号将会轮流出现在显示屏中。 干燥
度指示器中的小滴数量会随着烘干程序的进
展慢慢下降。
更改程序
若要更改错误选择的程序,在程序启动时,
先将程序选择器转到 O 关闭 然后重置程
序。
程序一旦启动,就无法直接更改。 如果
您仍然尝试使用程序旋钮或附加功能按
钮(除了BUZZER[蜂鸣器]按钮)更改
程序,START/PAUSE(开始/暂停)按
钮和
将会在显示屏中闪烁。 但
是,烘干程序将不会受到此操作的影
响。
在必要时取出衣物或装载衣物
警告! 衣物和烘干槽会变热。 灼伤危
险!
1.
2.
3.
4.
打开装载门
装载或取出衣物。
稳固关闭机门。 必须听到锁定的声音。
按START/PAUSE(开始/暂停)按钮继
续烘干程序。
烘干程序完成/取出衣物
烘干程序一旦完成,
CREASE GUARD
(皱摺防护)便会在显示屏中亮起。 如果启
BUZZER(蜂鸣器),将会以固定
用了
间隔发出声音信号。
烘干程序之后将会自动执行抗皱摺阶
段,该阶段持续大约30分钟。
烘干槽将会在这个阶段间隔旋转。 这样即可
使衣物散开而不会出现皱摺。 在抗皱摺阶
段,您可以随时取出衣物。 (应该在抗皱摺
阶段的最后部分即将结束时取出衣物,以防
止皱摺的形成。)
1. 打开机门。
2. 取出衣物之前,先从微细过滤器取出绒
毛。 最好是弄湿双手再执行此操作。
(请参阅"清洁和保养"章节。)
3. 取出衣物。
4. 将程序旋钮转到 O 关闭。
5. 重要信息! 在每个烘干程序之后
– 清洁微细过滤器和细微滤网
– 排出冷凝水容器中的水(请参阅"清洁
和保养"章节。)
6. 关闭机门。
烘干架
烘干架能够让您烘干可洗涤的羊毛织品和运
动鞋。 烘干架不会和干衣机的烘干槽一起转
动。 这将允许烘干羊毛衣物或运动鞋。
如果潮湿,应该尽可能少移动羊毛织品,因
为它们会变得缠结,因此使用烘干架是一个
解决方案。
运动鞋则必须使用烘干架进行烘干,否则将
会因为鞋子的重量而损坏烘干槽。
如果是初次拆开架子包装,请参阅安装
章节。
警告! 安装架子之前,请检查干衣机的
烘干槽。 它必须是空的!
1. 打开装载门。
2. 插入架子。
将架子在烘干槽中水平升起。 向下引导
架子直到支撑支架处于开口处的前端。
42 electrolux
重要事项! 取出鞋垫并将它们放在架子上的
鞋子旁边。 绑好鞋带。
3. 将洗涤物放在架子上:
– 弹开架子上的衣物然后将衣物向上
卷,避免挤压或折叠衣物。
– 将运动鞋放在架子上。
4. 选择所需的程序运行时间,可选择的间
隔为10分钟,从30分钟 到180分钟。
根据需要,多次按TIME按钮,直到所需
的程序运行时间出现在显示屏中。
5. 按START/PAUSE按钮。 程序将会启
动。
6. 在烘干程序结束时,打开装载门并取出
衣物或鞋子。
7. 将程序选择器转到 O 关闭。
8. 在结束烘干时从烘干槽中取出架子。
清洁和保养
清洁纤维屑滤网
为了确保干衣机完美操作,必须在执行每个
Iron Aid TM或烘干程序之后清洁机门内和烘
干槽前端的纤维屑滤网。
小心! 重要信息。 请勿使用没有安装纤
维屑滤网或纤维屑滤网损坏或阻塞的干
衣机。
1. 打开装载门
2. 使用潮湿的手清洁微细过滤器,该过滤
器内建于装载孔的底端部分。
3. 经过一段时间之后,会因为衣物上的清
洁剂残余物导致过滤器上形成一个薄
层。 出现上述情况时,请使用刷子和温
水清洗过滤器。 拉出机门,取出机门内
的过滤器。 您可以将它定位,使齿轮的
electrolux 43
齿朝向左边或右边。 清洗之后,务必记
得将它放回原位。
1
2
2. 将阀/过滤器放在温水下清洗。
4. 从纤维屑滤网取出绒毛,最好是弄湿双
手再执行此操作。
5. 装回过滤器
3. 装回阀/过滤器。
4. 将阀/过滤器转到ON位置。
清洁水循环阀/过滤器
蒸汽过滤器符号出现在显示屏中,
如果
即表示需要清洁循环过滤器。 阀/过滤器位
于槽把手的后面 - 请参阅"产品说明"。
1. 向下按水槽过滤器颈(1)然后将它拉出
(2)。
清洁机门密封垫
执行Iron Aid或烘干程序后,立即使用湿布
擦拭机门密封垫。
清空冷凝水容器
执行每个烘干程序后清空冷凝水容器。 如果
冷凝水容器已满,执行中的程序将会自动中
断,且
图标显示将会亮起。 若要继续执
行程序,必须先清空冷凝水容器。
44 electrolux
警告! 冷凝水不适合饮用或用于预备食
品。
使用随附的罐子过滤: 将容器内的水通
过罐子顶部的过滤器直接倒出。
1. 将包含冷凝水的隔间完全拉出(1)然后尽
可能向上拉冷凝水容器的排水管(2)。
清洁热交换器
热交换器,则表示需要清洁热
如果显示
交换器。
2.
1.
小心! 在热交换器被绒毛阻塞时操作将
会损坏干衣机。 这样也会提高能源消
耗。
1. 打开机门。
2. 打开底座的机门。 若要执行此操作,可
按门孔底部的释放按钮,然后向左打开
底座的机门。
2. 将冷凝水倒入水盆或类似容器中。
3. 推入排水管然后装回冷凝水容器。
如果程序因为冷凝水容器已满而中断:
按START/PAUSE按钮继续烘干程序。
3. 从机门内部和热交换器前室清洁绒毛。
用湿布擦拭机门密封垫。
4. 将两个锁垫圈向内转动。
冷凝水容器的容量约为 4升。 这将足够
用于先前在1000转/分钟转速下脱水的大
约7公斤衣物。
4. 冷凝水可作为蒸馏水使用,例如,用于
蒸汽烫斗。 但是,必须先过滤冷凝水以
去除任何残余物和小绒毛。
5. 使用把手将热交换器拉出底座,并将它
水平移动以防止任何残余的水溢出。
electrolux 45
如果
热交换器仍然亮起,干衣机将
无法操作。
小心! 切勿操作不具备热交换器的干衣
机。
清洁烘干槽
小心! 请勿使用研磨剂或钢丝绒来清洁
烘干槽。
水或清洁剂中的石灰可能会在烘干槽内
部形成几乎不能看见的内层。 衣物的烘
干程度将无法再可靠检测。 衣物从干衣
机取出时比预期更潮湿。
6. 若要清空热交换器,可垂直握住洗涤
碗。
小心! 请勿使用尖锐物件进行清洁工
作。 这样会使热交换器逐渐泄漏。
7. 清洁热交换器。
最好使用刷子或使用手持淋浴器彻底冲
洗。
8. 装回热交换器并锁定到位(将两个锁垫
圈向外转动直到它们卡入定位)。
9. 关闭底座的机门。
使用标准的家用清洁剂(例如,含醋的清洁
剂)向下擦拭烘干槽的内部和烘干槽骨架。
清洁控制面板和机架
小心! 请勿使用家具清洁剂或强力清洁
剂来清洁干衣机。
使用湿布向下擦拭控制面板和机架。
如果发生下列情况应如何...
自行排解疑难
如果在运作过程中,错误代码E和一个数字
或字母出现在多重显示屏上: 关闭干衣机电
问题
干衣机无法操作。
IronAid程序无法启动。
水槽指示灯亮起。
执行IronAid程序后,衣物
未足够柔顺。
源然后再打开。 重置程序。 按START/
PAUSE按钮。 如果错误再次出现,请联系
客户服务部门并说明错误代码。
可能的原因
解决方法
未插入电源插头或保险丝未正确操
作。
将插头插入电源插座。 检查保险丝
盒内的保险丝(家庭安装)。
装载门打开。
关闭装载门。
您是否按下START/PAUSE按钮?
再次按下START/PAUSE按钮。
水槽是空的。
填充水槽。
循环阀关闭(OFF位置)。
将循环阀转到ON位置。
选择了错误程序(例如,
SYNTHETICS而不是
COTTON)。
注意织品的成分。
设置的LOAD水平过低。
设置较高的LOAD。
干衣机内的衣物过多,或异物差别
在干衣机内装载较少或类似衣物。
太大。
衣物在抗皱摺阶段完成后才可取
出。
启动抗皱摺阶段后,尽快从干衣机
一次取出一件衣物。
衣物未挂在衣架上和/或未拖拉成
形。
将衣物挂在衣架上,扣好纽扣并拖
拉成形。
多层衣物经常失去其形状。
将多层衣物从干衣机取出后熨烫以
恢复其形状。
46 electrolux
执行IronAid程序后,衣物
不再出现皱摺。
IronAid具备柔顺衣物的效果。
执行Iron Aid程序后再次熨烫皱摺。
烘干效果不理想。
选择了错误程序。
在下次烘干时选择不同的程序(请
参阅"程序概观"章节)。
纤维屑滤网阻塞。
清洁纤维屑滤网。
绒毛过滤器阻塞。
清洁绒毛过滤器。
热交换器门被纤维屑阻塞。
清洁热交换器。
衣物超载。
遵循建议的装载量。
底部区域的通风槽被遮蔽。
解除底部区域通风槽的遮蔽。
烘干槽的内部表面或烘干槽骨架上
出现残余物。
清洁烘干槽的内部表面和烘干槽骨
架。
使用DRYNESS功能进行调节(请
参阅"烘干"章节)
安装场地的水导率和机器的标准设
置不同。
重新编程烘干程度的标准设置(请
参阅"编程选项"章节)。
按下按钮时 - 干衣机没有
反应。
烘干防护。 启动程序后,不可再设 将程序旋钮转到OFF。 再次设置程
置选项。
序。
烘干槽照明无法操作。
程序选择器处于OFF位置。
将程序选择器转到任何程序。
灯泡出现瑕疵。
更换灯泡(请参阅下一章节。)
显示的程序时间不规律变
化,或长时间保持一样。
根据衣物的类型和数量,程序时间
自动处理; 这不是干衣机故障。
将会自动更正。
程序停止,
亮起。
冷凝水容器已满。
容器显示
清空冷凝水容器,然后使用
START/PAUSE按钮启动程序。
烘干程序在启动程序后不
抗皱摺显示
久结束。
亮起。
选择时间程序或较高的烘干水平
装载的洗涤物不足,或装载的洗涤
EXTRA而不是
物对于所选的程序而言过于干燥。 (例如,
CUPBOARD)。
烘干程序持续不寻常的长
时间。 注意: 烘干程序在
最多5小时内自动结束(请
参阅"结束烘干程序")。
纤维屑滤网阻塞。
清洁纤维屑滤网。
绒毛过滤器阻塞。
清洁绒毛过滤器。
装载量过大。
减少装载量。
衣物脱水不足。
衣物必须足够脱水。
特别高的室温。 暂时关闭压缩器以 自动处理,干衣机没有故障。 如有
避免超载。
可能,降低室温。
变色。
纺织品褪色。
更换内部照明的灯泡
仅使用特别为干衣机设计的特殊灯泡。 您可
以从当地的服务团队中心获取特殊灯泡。
警告! 打开干衣机时,内部照明将会在
打开机门情况下的4分钟后自动关闭。
警告! 请勿使用标准灯泡! 这些灯泡会
积聚过多的热并可能会损坏干衣机!
警告! 更换灯泡之前,请先拔下电源插
头。
检查纺织品的褪色。 仅一起处理具
有类似颜色的纺织品。
1. 松开灯泡上方灯罩的螺丝钉(可在位于
顶部的装载孔正背面找到; 请参阅"干衣
机说明"章节。)
2. 更换灯泡。
3. 用螺丝钉栓紧灯罩。
用螺丝钉栓紧机门灯罩之前,检查o形垫圈
的位置是否正确。 如果机门灯罩上缺少o形
垫圈,请不要操作干衣机。
警告! 为了安全起见,必须用螺丝钉栓
紧灯罩。 如果不这么做,切勿操作干衣
机。
electrolux 47
技术数据
此干衣机符合下列欧盟指示:
– 于12.12.2006发布的2006/95/EC 低电压指示
– 于03.05.1989发布的89/336/EEC EMC 指示,包括修正指示92/31/EEC
– 于22.07.1993发布的93/68/EEC CE标记指示
高度 x 宽度 x 深度
85 x 60 x 58 厘米
烘干槽容量
108升
打开装载门时的深度
109厘米
高度可调节
1.5厘米
清空时的重量
大约 46公斤
装载量(取决于程序)1)
最多 7 公斤
电压
230V-240V
需要的保险丝
10A
总功率
2350
能源效率等级
B
能源消耗(7公斤棉质,在1000 rpm转速下预
先排水)2)
3,9
使用
家庭
允许的环境温度
+ 5°C 至 + 35°C
水电消耗值
水电消耗值在标准情况下制定。 该值在家庭环境下操作干衣机时可能会偏差。
程序
以kWh表示的能源消耗
COTTONCUPBOARD 2)
4,0(7公斤装载量,在800 rpm转速下预先排水)
3,9 (7公斤装载量,在1000 rpm转速下预先排
水)
3.6(7公斤装载量,在1400 rpm转速下预先排水)
COTTONIRON 2)
3.3 (7公斤装载量,在1000 rpm转速下预先排
水)
SYNTHETICSCUPBOARD2)
1,3 (7公斤装载量,在1200 rpm转速下预先排
水)
1) 因为测量方法不同,一些国家可能需要不同的装载量数据。
2) 根据EN 61121
干衣机设置
设置
蜂鸣器永久关闭
执行
1. 将程序选择器转到任何程序。
2. 同时按下 DRYNESS (干燥度)和 DELICATE (纤细衣物)
按钮并按住大约 5秒。
3. 在默认情况下,蜂鸣器将始终关闭。 您可以使用 BUZZER
(蜂鸣器)按钮来启用或禁用声音,但干衣机不会记住您的选
择。
48 electrolux
水质硬度
1. 将程序选择器转到任何程序。
水包含不固定数量的石灰石和 2. 同时按下 DELICATE (纤细衣物)和 START/PAUSE (开
始/暂停)按钮并按住大约 5秒。 当前设置将会出现在显示屏
矿盐,其数量会根据地理位置
而有所不同,从而也改变其传
上:
导性值。
–
低传导性 <300 微秒/厘米
水传导性的相应变化与那些工
–
中等传导性300-600微秒/厘米
厂预先制定的值比较,会稍微
–
高传导性 >600 微秒/厘米
影响程序结束时的衣物残余湿
度。。 您的干衣机允许您根据 3. 继续按 START/PAUSE (开始/暂停)按钮,直到您设置所需
的水平为止。
水的传导性值调节烘干传感器
4. 若要记住设置,可同时按下 DELICATE (纤细衣物)和 START/
的灵敏度。
PAUSE (开始/暂停)按钮,或将旋钮转到 O 关闭位置。
测试学会的提示
可让测试学会检查的参数:
• 正常装载量下的衣橱干棉质程序期间的能
源消耗(使用最终湿度更正)。
• 一半装载量下的衣橱干棉质程序期间的能
源消耗(使用最终湿度更正)。
• 最终湿度(在衣橱干棉质期间,熨烫干棉
质和衣橱干免烫)
• 正常和一半装载量下的衣橱干棉质程序期
间的凝结效率(使用最终湿度更正)。
所有程序必须根据EN 61121(家用滚筒干
衣机, - 测量性能的方法)进行检查。
安装
重要事项! 运输此干衣机时,必须直向移
动。
重要事项! 切勿将干衣机安装在可锁定的
门、干衣机对面具有铰链的滑动门后面。
放置干衣机
• 为了您的方便,建议将干衣机放置在靠近
洗衣机的地方。
• 必须将滚筒干衣机安装在一个干净、不会
累积尘埃的地方。
• 干衣机周围的空气必须能够自由流通。 请
勿阻挡前端的通风栅,或干衣机背面的通
风口栅。
• 若要保持使用干衣机时最低的震动和噪
音,应该将它放置在一个平稳的表面上。
• 设置其永久操作位置后,检查并确定在使
用水平仪帮助下干衣机绝对水平。 若不
是,可升高或降低机脚直到其水平为止。
• 切勿卸下机脚。 请勿使用deeppile地毯、
木条或类似物体来限制地面间隔。 这样可
能会导致热积聚而影响干衣机的操作。
拆除运输器防护包装
小心!
使用运输器的所有部件之前,必须拆除包
装。
1. 打开装载门
2. 从干衣机内部烘干槽顶部撕下粘带。
重要事项!
滚筒干衣机发出的热空气可高达60°C温
度。 因此必须将干衣机安装在可抵抗高温的
地面上。
操作滚筒干衣机时,室温必须不能低于+5°C
和高于+35°C,因为这样会影响干衣机的性
能。
重要事项! 若要移动干衣机,必须直向搬
运。
3. 从机器拆除箔软管和聚苯乙烯垫。
electrolux 49
电力连接
有关电源电压、电流类型和所需保险丝的详
细信息,可在铭牌上查找。 铭牌位于靠近装
载孔的地方(请参阅"产品说明"章节)。
根据现行的电流布线规范,将干衣机连接到
接地的插座上。
警告! 制造商对于不遵循上述安全注意
事项而导致的损坏或伤害不承担任何责
任。
若需要更换干衣机的电源线,请仅让授
权的服务工程师或合格电工执行此操
作。 .
拆除烘干架包装
小心! 使用所有包装部件和架子之前,
必须从烘干槽取处它们。
若要拆除架子包装:
1. 撕开顶部的防护聚苯乙烯部件将它拆
除。
1
干衣机随附安装好的13 amp插头。 如果需
要更换随附插头内的保险丝,必须使用13
amp ASTA认可的BS 1363/A保险丝。
4
1
3
1
2. 稍微抬高架子把手(不是到末端)。
若要以最轻松的方式拆除包装,可反转
架子。
3. 小心将它从烘干槽取出。
3
2
2
电源线内的电线颜色按照下列规范分配:
1 蓝色 - 中性线
2 电线夹
3 褐色 - 电线
4 绿色和黄色 - 地线
绿色和黄色电线必须连接到标有"E"或接地符
或是绿色和黄色的终端。
号
蓝色电线必须连接到标有"N" 或是黑色的终
端。
褐色电线必须连接到标有"L" 或是红色的终
端。
完成后,必须没有切割,或出现散开的电
线,以及必须将电线夹固定在外部套管上。
警告! 将切断的插头插入13 amp插座是
一个严重危及安全(触电)的动作。
请确定安全处置切断的插头。
4. 从烘干槽中取出其余元件。
警告! 安装干衣机后,必须能够插拔插
头。
50 electrolux
永久连接
如果要永久连接,您必须在干衣机和电源供
应之间安装一个双极开关,且开关接点之间
必须具有至少3毫米的间隙,以及在现行电
气规范下适合所需负载的类型。
开关的黄色和绿色地线在任何接点都必须不
能断开。
更换门掣
8. 松开门锁 E 的螺丝钉,稍微向下按并从
干衣机前端取出。
9. 按入和向下按嵌入按钮 F ,稍微向下按
盖板并从干衣机前端取出。
10. 将门锁 E 换到对面侧,用螺丝钉按顺时
针方向栓紧门互锁。
E
警告! 更换门掣之前,请先拔下电源插
头。
1. 打开装载门。
2. 从干衣机前端松开铰链 A 的螺丝钉,并
将它从装载门取下。
3. 卸下盖板 B 。 若要执行此操作,可如图
所示将一支薄的螺丝起子插入槽中,稍
微向下按然后撬出盖板。
G
F
E
F
A
C
B
D
A
C
4. 使用适当工具并施加压力从嵌入装置解
开锁定块 C ,取出并旋转锁定块180°然
后重新插入另一侧。
5. 从装载门松开铰链 A 的螺丝钉,旋转
180°,重新插入对面侧然后栓紧螺丝
钉。
6. 先将盖板 B 旋转180°,然后重新插入对
面侧。
7. 从干衣机前端松开盖板 D 的螺丝钉,旋
转180°,然后用螺丝钉栓紧在对面侧。
G
11. 在另一侧,插入盖板 F 然后允许嵌入按
钮锁入定位。
12. 将装载门和铰链插入干衣机前端的凹
处,然后用螺丝钉栓紧。
关于接点保护的注释: 只有在插入所有塑料
部件之后才可再次安全使用干衣机。
特殊附件
您可以从您的伊莱克斯服务团队中心或您的
专业零售商获取特殊附件。
堆叠洗衣机和iron aid干衣机的中间安装套
件:
这些中间安装套件可用来排列iron aid干衣机
和伊莱克斯自动洗衣机(60厘米宽,前载
式)作为节省空间的洗衣机/iron aid堆叠。
自动洗衣机在下面而iron aid干衣机在上
面。 提供两个版本:
• 不带堆叠器板
• 带可引出的堆叠器板
请仔细阅读安装套件随附的手册。
服务
若出现技术故障,请先检查您是否可借助操
作说明自行解决问题 - 请参阅 "如果发生下
列情况应如何..."章节。
如果您无法自行解决问题,请联系客户服务
部门或我们的其中一个服务合作伙伴。
为了可以更快帮助您,我们需要下列信息:
electrolux 51
- 型号说明
- 产品编号(PNC)
- 序列号(序列号位于粘贴到产品的铭牌上
- 若要查找该序列号,请参阅 产品说明 章
节。)
- 故障类型
- 干衣机所显示的任何错误信息
当您从干衣机获取必要的参考编号后,我们
建议您在此处记下这些信息:
型号说明:
产品编号:
序列号:
www.electrolux.com
www.electrolux.com.my
www.electrolux.com.sg
www.electrolux.cn
136908690-01-03022009
Download PDF

advertising