AEG | F99015IM0P | User manual | Aeg F99015IM0P User Manual

Aeg F99015IM0P User Manual
FAVORIT 99015 I
EN DISHWASHER
USER MANUAL
2
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler – features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Contents
3
CONTENTS
4
6
7
11
11
13
13
15
15
17
19
20
22
25
25
26
30
30
31
Safety information
Product description
Control panel
Use of the appliance
Setting the water softener
Use of dishwasher salt
Use of detergent and rinse aid
Multitab function
Loading cutlery and dishes
Washing programs
Setting and starting a washing
program
Care and cleaning
What to do if…
Technical data
Installation
Water connection
Electrical connection
Environment concerns
Warranty
The following symbols are used in this user
manual:
Important information concerning your
personal safety and information on how to
avoid damaging the appliance.
General information and tips
Environmental information
Subject to change without notice.
4
Safety information
SAFETY INFORMATION
For your safety and correct operation of the appliance, read this manual carefully before
installation and use. Always keep these instructions with the appliance even if you move or
sell it. Users must fully know the operation and safety features of the appliance.
Correct use
• Only use the appliance to clean household utensils that are suitable for dishwashers.
• Do not put solvents in the appliance. Risk of explosion.
• Put knives and all items with sharp points in the cutlery basket with their points down. If
not, put them in a horizontal position in the upper basket.
• Use only products specified for dishwashers (e.g. detergent, salt, rinse aid).
• If you open the door while the appliance is in operation, hot steam can escape. Risk of
skin burns.
• Do not remove dishes from the appliance before the end of the washing program.
• When the washing program is completed, disconnect the mains plug from the mains
socket and close the water tap.
• Only an authorised service engineer can repair this appliance. Use only original spare
parts.
• Do not do repairs yourself to prevent injury and damage to the appliance. Always contact the Customer Care Centre.
General safety
• This appliance is intended to be used in household and similar applications such as:
– Staff kitchen areas in shops, offices and other working environments
– Farm houses
– By clients in hotels, motels and other residential type environments
– Bed and breakfast type environments.
• Some dishwasher detergents are strongly alkaline. They can be extremely dangerous if
swallowed. Avoid contact with skin and eyes. Keep the children away from the appliance
when the door is open. Check that the detergent dispenser is empty after completion of
the washing program.
• Obey the safety instructions from the manufacturer of the dishwasher detergent to prevent burns to eyes, mouth and throat.
• Only put detergent in the dispenser before you start a washing program.
• Do not drink the water from the appliance. Detergent residue can stay in your appliance.
• Always close the door when you do not use the appliance to prevent injury and not to
stumble over the open door.
• Do not sit or stand on the open door.
Safety information
5
Child safety
• Do not let persons, children included, with reduced physical sensory, reduced mental
functions or lack of experience and knowledge use the appliance. They must have supervision or instruction for the operation by a person who is responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Keep all the packaging away from children. There is a risk of suffocation.
• Keep all detergents in a safe area. Do not let children touch the detergents.
• Keep children and pets away from the appliance when the door is open.
Installation
• Make sure that the appliance is not damaged because of transport. Do not connect a
damaged appliance. If necessary, contact the supplier.
• Remove all packaging before first use.
• A qualified and competent person must do the electrical installation.
• A qualified and competent person must do the plumbing installation.
• Do not change the specifications or modify this product. Risk of injury and damage to
the appliance.
• Do not use the appliance:
– If the mains cable or the water hoses are damaged.
– If the control panel, worktop or plinth area are damaged so that you can get access to
the inner side of the appliance.
Contact your local Customer Care Centre.
• Do not drill into the sides of the appliance otherwise damage to hydraulic and electrical
components may occur.
WARNING!
Follow carefully the instructions for electrical and water connections.
6
Product description
PRODUCT DESCRIPTION
10
1
9
2
3
4
5
1
2
3
4
5
6
7
8
9
10
8
7
6
Upper basket
Air vent and water hardness dial
Salt container
Detergent dispenser
Rinse aid dispenser
Rating plate
Filters
Lower spray arm
Upper spray arm
Top spray arm
Internal light
This appliance has an internal light that comes on when you open the door and goes off
when the door is closed.
If it is necessary to replace the light, contact your local Customer Care Centre.
Control panel
7
CONTROL PANEL
Messages in the display and acoustic signals will help you to operate with the appliance.
1
4
3
2
6 5
8 7
1
2
3
4
5
6
7
8
On/off button
Menu touchpad (up)
Display
Return touchpad
Start touchpad
OK touchpad
Menu touchpad (down)
Display touchpad
On/off button
Press this button to switch on or off the appliance.
After 10 minutes from the end of the washing program, the AUTO OFF function automatically switches off the appliance. This helps to decrease energy consumption.
Display
A
B
C
02:28
13:08
Options
The display has three areas. To operate in an area, press the display touchpad until the
frame of the area comes on.
8
Control panel
Programs area (A)
This area shows the menu with the washing programs and the time of each program. To set
the washing program, refer to 'Washing programs'.
1. Press the display touchpad to go to this area.
2. Press one of the menu touchpads. The display shows:
• The menu with the washing programs
• The time of each program.
3. Press one of the menu touchpads to set a washing program.
4. Press the OK touchpad. The display shows the three areas:
• Area (A) shows the washing program and the time of the program.
• Area (B) shows the time to the end of the washing program.
End Time area (B)
You can delay the start of the washing program from 1 to 24 hours.
1. Press the display touchpad to go to this area.
2. Press one of the menu touchpads to set the number of hours for the delay start.
• The upper part of the area shows the delay start.
• The lower part of the area shows the end time of the washing program.
3. Press the OK touchpad.
4. Press the return touchpad to close the menu option and go back to area (A).
Options area (C)
1.
2.
3.
4.
Press the display touchpad to go to this area.
Press one of the menu touchpads to go through the menu option.
Press the OK touchpad to set a function or to open the submenu.
Press the return touchpad to close the menu option and go back to area (A).
Menu option
Menu
Submenu
Description of the function
Multitab
On
Off
If you use the combi detergent tablets ('3 in 1', '4 in 1',
'5 in 1'), use the multitab function. Refer to 'Multitab
function'.
Extra hygiene
On
Off
This function gives better results for the hygiene. During the rinsing phase, the temperature stays at 70 °C
for 10 to 14 minutes.
The function can be activated with all washing programs but has effect only on some programs. To see
where this function has effect, refer to the 'Washing
programs' chart.
Control panel
Menu
Submenu
9
Description of the function
ProBoost
On
Off
This function increases the water pressure by 40%.
This function gives better washing results when the
dishes are very dirty.
The function can be activated with all washing programs but has effect only on some programs. To see
where this function has effect, refer to the 'Washing
programs' chart.
Settings
Language English
You can set the language of the messages in the display.
(Different languages
are available).
Sound volume
On
Off
(5 levels are available).
You can adjust the volume of all the acoustic signals.
Level 0 = volume off.
Factory setting: 5.
Time
You can set the time.
Brightness
You can increase or decrease the brightness of the display.
Factory setting: 10.
(10 levels are available).
Contrast
(10 levels are available).
Reset settings
You can go back to the factory setting of the appliance.
Water hardness
You can adjust the level of the water softener. Refer to
'Setting the water softener'.
Factory setting: 5.
(10 levels are available).
Wash guide
You can increase or decrease the contrast of the display.
Factory setting: 6.
Rinse aid
On
Off
You can activate the rinse aid dispenser. This function
is available only when the multitab function is on.
Back
To go back to the menu option.
Program guide
The display shows information about the washing programs.
Option guide
The display shows information about the functions.
10
Control panel
Menu
Submenu
Description of the function
Demo mode
On
Off
You can simulate a washing program. Refer to Demo
mode .
Factory setting: Off .
Back
To go back to the menu option.
Demo mode
1.
2.
3.
4.
5.
Go to the menu option.
Go to Wash Guide .
Press the OK touchpad to open the submenu.
Go to Demo mode and activate the function.
Press the display touchpad.
• The display shows the three areas (A), (B) and (C).
• The top left corner of the display shows DEMO. The function is activated.
To go back to the daily use of the appliance, remember to deactivate the Demo mode function.
Use of the appliance
11
USE OF THE APPLIANCE
Switching on the appliance for the first time
1. Switch on the appliance.
2. The display shows the default language: Language English.
• Press the OK touchpad to confirm the default language
• Press one of the menu touchpads to set a different language and then press the OK
touchpad to confirm.
3. The display shows the time message.
4. Press one of the menu touchpads to set the time.
5. Press the OK touchpad.
6. The display goes to 'Programs' area.
Using the appliance
1. Be sure that the set level of the water softener agrees with the water hardness in your
area. If not, adjust the water softener.
2. Fill the salt container with dishwasher salt.
3. Fill the rinse aid dispenser with rinse aid.
4. Load cutlery and dishes into the appliance.
5. Set the correct washing program for the type of load and soil.
6. Fill the detergent dispenser with the correct quantity of detergent.
7. Start the washing program.
If you use the combi detergent tablets ('3 in 1', '4 in 1', '5 in 1'), use the multitab function.
Refer to 'Multitab function'.
SETTING THE WATER SOFTENER
The water softener removes minerals and salts from the water supply. Minerals and salts
can have bad effect on the operation of the appliance.
Water hardness is measured in equivalent scales:
• mg/I (millimol per litre)
• ppm (parts per million),
• mmol/l (millimol per litre - international unit for the hardness of water).
Adjust the water softener in to the water hardness in your area. If necessary, contact your
local water authority.
Water hardness
Water hardness setting
mg/l
ppm
mmol/l
manually
electronically
910 - 1250
910 - 1250
9.1 - 12.5
2
10
760 - 909
760 - 909
7.6 - 9.0
2
9
12
Setting the water softener
Water hardness
Water hardness setting
mg/l
ppm
mmol/l
manually
electronically
650 - 759
650 - 759
6.5 - 7.5
2
8
510 - 649
510 - 649
5.1 - 6.4
2
7
400 - 509
400 - 509
4.0 - 5.0
2
6
330 - 399
330 - 399
3.3 - 3.9
2
5
260 - 329
260 - 329
2.6 - 3.2
1
4
190 - 259
190 - 259
1.9 - 2.5
1
3
70 - 189
70 - 189
0.7 - 1.8
1
2
< 70
< 70
< 0.7
1
11)
1) No use of salt required.
You must set the water softener manually and electronically.
Manual adjustment
The appliance is set at the factory at position 2.
1. Remove the lower basket.
2. Turn the water hardness dial to position 1
or 2 (refer to the chart).
3. Put back the lower basket.
Electronic adjustment
1.
2.
3.
4.
5.
6.
7.
8.
Open the menu option.
Go to Settings .
Press the OK touchpad to open the submenu.
Go to Water hardness .
Press the OK touchpad.
Set the level of the water softener.
Press the OK touchpad.
Press the return touchpad to close the menu option.
Use of dishwasher salt
13
USE OF DISHWASHER SALT
CAUTION!
Only use dishwasher salt. Types of salt that are not suitable for dishwashers cause damage
to the water softener.
CAUTION!
Grains of salt and salty water on the bottom of the appliance can cause corrosion. Fill the
appliance with salt before you start a washing program.
Filling the salt container
1. Turn the cap counterclockwise to open the salt container.
2. Fill the salt container with 1 litre of water (only the first operation).
3. Use the funnel to fill the salt container
with salt.
4. Remove the salt around the opening of
the salt container.
5. Turn the cap clockwise to close the salt
container.
When the salt container is empty, the display
shows a message to inform you to refill with
salt. The message does not show while a
washing program operates.
It is normal that water overflows from the
salt container when you replenish it.
After the replenishment of the salt container, the display can continue to show the message for some hours. This does not have an unwanted effect on the operation of the appliance
USE OF DETERGENT AND RINSE AID
1
3
2
4
30
7
4
MA X
+
3 2
-
1
20
6
5
14
Use of detergent and rinse aid
Use of detergent
CAUTION!
Only use detergents (powder, liquid or tablet) that are suitable for dishwashers.
Follow the recommendations on the detergent packaging for the use and storage of the
detergent.
To help the environment, do not use more than the correct quantity of detergent.
Filling with detergent
1. Press the release button 2 to open the lid 7 of the detergent dispenser.
2. Put the detergent in the dispenser 1 .
3. If the washing program has a prewash phase, put a small quantity of detergent on the
inner part of the appliance door.
4. If you use the detergent tablets, put the tablet in the detergent dispenser 1 .
5. Close the detergent dispenser. Press the lid until it locks into position.
Different brands of detergent dissolve in different times. Some detergent tablets do not
have the best cleaning results during short washing programs. Use long washing programs
when you use detergent tablets to fully remove the detergent.
Use of rinse aid
CAUTION!
Only use rinse aid specified for dishwashers.
Do not fill the rinse aid dispenser with other products (e.g. dishwasher cleaning agent, liquid detergent). This can cause damage to the appliance.
Rinse aid makes it possible to dry the dishes without streaks and stains.
Rinse aid is automatically added during the last rinsing phase.
Rinse aid is automatically added during the last rinsing phase.
1. Press the release button 6 to open the lid 5 of the rinse aid dispenser.
2. Fill the rinse aid dispenser 3 with rinse aid. The mark 'max' shows the maximum level.
3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam during
the washing program.
4. Close the rinse aid dispenser. Press the lid until it locks into position.
When it is necessary to fill the rinse aid dispenser, the display shows a message. The message does not show while a washing program operates.
Adjusting the rinse aid dosage
Factory set: position 3.
You can set the rinse aid dosage between position 1 (lowest dosage) and position 4 (highest
dosage).
Turn the rinse aid selector 4 to increase or reduce the dosage.
Wash hands to remove any residue of rinse aid from skin.
Multitab function
15
MULTITAB FUNCTION
The multitab function is for combi detergent tablets.
These tablets contain agents as detergent, rinse aid and dishwasher salt. Some types of tablets can contain other agents.
Be sure that these tablets are applicable for the water hardness in your area (refer to the
instructions on the packaging of the products).
The multitab function deactivates the flow of rinse aid and salt.
The multitab function deactivates the salt and the rinse aid messages.
The program duration can increase if you use the multitab function.
Activate or deactivate the multitab function before the start of a washing program. You
cannot activate or deactivate the function while a washing program operates.
To activate the multitab function
1. Open the menu option.
2. Go to Multitab and activate the multitab function.
• When you activate the multitab function, it stays on until you deactivate it.
3. Press the OK touchpad.
4. Press the return touchpad to close the menu option.
To deactivate the multitab function and use separately detergent, salt and
rinse aid
1.
2.
3.
4.
5.
6.
7.
8.
Open the menu option.
Go to Multitab and deactivate the multitab function.
Press the OK touchpad.
Press the return touchpad to close the menu option.
Fill the salt container and the rinse aid dispenser.
Adjust the water hardness to the highest level.
Start a washing program without dishes.
When the washing program is completed, adjust the water softener to the water hardness in your area.
9. Adjust the quantity of rinse aid.
LOADING CUTLERY AND DISHES
Refer to the leaflet 'Examples of ProClean loads'.
Helpful hints and tips
CAUTION!
Only use the appliance for household utensils that are suitable for dishwashers.
16
Loading cutlery and dishes
Do not use the appliance to clean objects that can absorb water (sponges, household cloths,
etc.).
• Before you load cutlery and dishes:
– Remove all remains of food and debris.
– Soften burnt remains of food.
• While you load cutlery and dishes:
– Load hollow items (e.g. cups, glasses and pans) with the opening down.
– Make sure that water does not collect in the container or in a deep base.
– Make sure that cutlery and dishes do not lie inside one another.
– Make sure that cutlery and dishes do not cover other cutlery and dishes.
– Make sure that glasses do not touch other glasses.
– Put small objects in the cutlery basket.
• Plastic items and pans with non-stick coatings can retain water droplets. Plastic items do
not dry as well as porcelain and steel items.
• Put light items in the upper basket. Make sure that the items do not move.
CAUTION!
Make sure that the spray arms can move freely before you start a washing program.
WARNING!
Always close the door after you load or unload the appliance. An open door can be dangerous.
Beer glass holders
The beer glass holders prevent beer glasses to
move while a washing program operates.
If you do not use the holders, fold them up or remove them. You can also remove the support.
WARNING!
Be careful when you disengage or engage the support.
Washing programs
Follow these steps to remove the holders and the support:
1. Disengage the holders from the support
and remove them.
2. Push the support to the rear part of the
basket to disengage it.
Follow these steps to engage the holders and the support:
1. Push the support to the front part of the
basket to engage it.
2. Engage the holders on the support.
WASHING PROGRAMS
Program
Type of soil
Type of load
Program description
Functions
Automatic 1)
All
Crockery, cutlery, pots and
pans
Prewash
Wash 45 °C or 70 °C
Rinses
Dry
Extra hygiene
70° Pro
Heavy soil
Crockery, cutlery, pots and
pans
Prewash
Wash 70 °C
Rinses
Dry
ProBoost
Crockery and
cutlery
Prewash
Wash 50 °C
Rinses
Dry
Crockery and
cutlery
Wash 60 °C
Rinse
Extra Silent 2) Normal soil
60° Quick 3)
Fresh soil
Extra hygiene
17
18
Washing programs
Program
Type of soil
Type of load
Program description
Functions
50° Energy 4)
Normal soil
Crockery and
cutlery
Prewash
Wash 50 °C
Rinses
Dry
Extra hygiene
50 Minutes
Light soil
Crockery and
cutlery
Wash 55 °C
Rinses
Extra hygiene
ProZone 5)
Mixed soil
Crockery, cutlery, pots and
pans
Prewash
Wash 70 °C
Rinses
Dry
45° Glass
Normal or
light soil
Delicate crockery and glassware
Wash 45 °C
Rinses
Dry
Prewash
Use this program to quickly
rinse the dishes. This prevents
the remaining food to bond
on the dishes and bad odours
to come out from the appliance.
Do not use detergent with
this program.
Rinse
1) The appliance senses the type of soil and the quantity of items in the baskets. It automatically adjusts the
temperature and quantity of the water, the energy consumption and the program time.
2) This is the most silent washing program. The pump works at a very low speed to decrease the level of noise.
Because of the low speed, the program time is long.
3) With this program you can wash a load with fresh soil. It gives good washing results in a short time.
4) This is the standard program for test institutes. With this program you have the most efficient use of water and
energy consumption for crockery and cutlery with normal soil. Refer to the supplied leaflet for test information.
5) With this program you can wash a load with mixed soil. Very heavy soil in the lower basket and normal soil in
the upper basket. The water pressure in the lower basket is three times higher than in the upper basket. The
temperature of the water in the lower basket is 25% higher than in the upper basket.
Consumption values
Energy (kWh)
Program1)
Water (litre)
Automatic
0.9 - 1.7
8 - 15
70° Pro
1.4 - 1.6
13 - 14
Extra silent
1.1 - 1.2
9 - 11
60° Quick
0.8
9
50° Energy
0.67 - 0.81
9.6 - 11.6
50 Minutes
1.0 - 1.1
10 - 11
ProZone
1.3 - 1.5
14 - 15
45° Glass
0.8 - 0.9
11 - 12
Prewash
0.0.5
4
1) The display shows the time of the program.
Setting and starting a washing program
19
The water pressure and temperature, the variations of the mains supply and the quantity of
dishes can change the consumption values.
SETTING AND STARTING A WASHING PROGRAM
Starting the washing program
1.
2.
3.
4.
Close the appliance door.
Switch on the appliance.
Set the washing program and functions.
Press the start touchpad, the countdown of the delay start or the washing program
starts automatically.
• The start of the appliance does not automatically occur if the salt container and the
rinse aid dispenser are empty. The related messages show in the display. Press again
the start touchpad, the countdown of the delay start or the washing program starts.
• When the countdown of the delay start is completed, the washing program starts
automatically.
The opening of the appliance door interrupts the countdown of the delay start. When you
close the door, the countdown continues from the point of interruption.
Cancelling the delay start
1. Press the start touchpad.
2. Follow the indications in the display to cancel the delay start.
3. Press the start touchpad. The washing program starts automatically.
WARNING!
Only interrupt or cancel a washing program if necessary.
Attention! Open the door carefully. Hot steam and water can escape.
Interrupting a washing program
• Open the appliance door. The washing program stops.
• Close the appliance door. The washing program continues from the point of interruption.
Cancelling the washing program
If the washing program has not started, you can change the selection.
To change the selection while the washing program operates, it is necessary to cancel the
program.
1. Press the start touchpad.
2. Follow the indications in the display to cancel the washing program.
Make sure that there is detergent in the detergent dispenser before you start a new washing program.
End of the washing program
When the washing program is completed, an intermittent acoustic signal sounds and the
display shows a message.
20
Care and cleaning
1. Switch off the appliance.
2. Open the appliance door.
For better drying results, keep the appliance door ajar for some minutes.
Removing the load
• Let the dishes cool down before you remove them from the appliance. Hot dishes are
easily damaged.
• First remove items from the lower basket, then from the upper basket.
• There can be water on the sides and door of the appliance. Stainless steel becomes cool
more quickly than the dishes.
CARE AND CLEANING
To remove and clean the filters
WARNING!
Switch the appliance off before you carry out any cleaning operation.
Dirty filters decrease the washing results. Although the maintenance is very low with these
filters, we recommend that you regularly check the filters and clean them if necessary.
1. To remove filter (A), turn it counterclockwise and remove it out from filter (B).
B
A
2. Filter (A) has 2 parts. To disassemble the
filter, pull them apart.
3. Thoroughly clean the parts under running
water.
4. Put the 2 parts of the filter (A) together
and push. Make sure that they assemble
correctly in each other.
5. Remove filter (B).
6. Thoroughly clean filter (B) under running
water.
Care and cleaning
7. Put filter (B) to its initial position. Make
sure that it assembles correctly under the
two guides (C).
8. Put filter (A) into position in filter (B) and
turn it clockwise until it locks.
21
C
Cleaning the spray arms
Do not remove the spray arms.
If the holes in the spray arms become clogged, remove remaining parts of soil with a thin
pointed object.
External cleaning
Clean the external surfaces of the appliance and control panel with a damp soft cloth. Only
use neutral detergents. Do not use abrasive products, scouring pads or solvents (e.g. acetone).
Internal cleaning
We recommend, every 3 months to run a washing program for heavily soiled dishes. Use
detergent, but do not put dishes in the appliance.
When the appliance is not to be used for a long period
1.
2.
3.
4.
Disconnect the mains plug from the mains socket.
Close the water tap.
Leave the door open to prevent unpleasant smells.
Keep the inner side of the appliance clean.
Frost precautions
CAUTION!
Do not install the appliance where the temperature is below 0 °C. The manufacturer is not
responsible for damage caused by frost.
Moving the appliance
1.
2.
3.
4.
Disconnect the mains plug from the mains socket.
Close the water tap.
Remove the appliance and the hoses.
Do not tilt the appliance during transport.
22
What to do if…
WHAT TO DO IF…
The appliance does not start or stops during operation.
If there is a fault, first try to find a solution to the problem yourself. Refer to following
charts. If you cannot find a solution to the problem, contact your dealer or the Customer
Care Centre
With some malfunctions, the display shows a message and an intermittent acoustic signal sounds.
WARNING!
Switch the appliance off before you do the suggested corrective actions.
Malfunction
The appliance does
not fill with water
Possible cause
Possible solution
The water tap is closed.
Open the water tap.
The filter in the water inlet hose is
blocked.
Clean the filter.
The installation of the water inlet
hose is not correct. The hose is bent
or squashed.
Make sure that the installation is
correct.
The water tap is blocked or restricted Clean the water tap.
with limescale.
The appliance does
not drain the water
The water pressure is too low.
Contact your local water authority.
There is a blockage in the sink spigot.
Clean the sink spigot.
The installation of the water drain
hose is not correct. The hose is bent
or squashed.
Make sure that the installation is
correct.
The anti-flood device
operates
The program does
not start
Close the water tap and contact
your Customer Care Centre.
The appliance door is not closed. The
display shows a message.
Close the door.
The start touchpad has not been
pressed.
Press the start touchpad.
Mains plug is not connected.
Plug-in the appliance to the mains.
The delay start is set.
• Cancel the delay start.
• Wait until the countdown of the
delay start is completed.
The fuse has blown out in the
household fuse box
Replace the fuse.
After the check, switch on the appliance. The program continues from the point of interruption. If the malfunction occurs again, contact your Customer Care Centre.
If the display shows other messages, related to malfunctions not described in the chart,
contact your Customer Care Centre.
What to do if…
23
When you contact the Customer Care Centre you will need to give some details of the appliance that can be found on the rating plate (e.g. model number, serial number, product
number). We recommend that you record these details.
The washing results and drying results are not satisfactory
Problem
The dishes are not clean.
Possible cause
Possible solution
The selected washing program Make sure that the washing
was not suitable for the type of program is suitable for the type
load and soil.
of load and soil.
The baskets were not loaded
correctly, water did not touch
all surfaces.
Load the baskets correctly.
The spray arms could not turn
freely because of incorrect arrangement of the load.
Make sure that an incorrect arrangement of the load does not
cause a blockage of the spray
arms.
The filters are dirty or not asMake sure that the filters are
sembled and installed correctly. clean and correctly assembled
and installed.
The quantity of detergent was
not sufficient or missing.
Make sure that the quantity of
detergent is sufficient.
The salt container is empty.
Fill the salt container with salt
for dishwashers.
The water softener is adjusted
on a wrong level.
Adjust the level of the water
softener.
The salt container cap is not
closed correctly.
Ensure that the salt container
cap is correctly closed.
There are streaks, milky stains,
or a bluish layer on glasses and
dishes.
Rinse aid dosage is too high.
Decrease the rinse aid dosage.
Dry water drop stains on
glasses and dishes.
Rinse aid dosage is too low.
Increase the rinse aid dosage.
The detergent can be the
cause.
Use a different brand of detergent.
The dishes are wet.
You have set a washing program without drying phase or
with a decreased drying phase.
Let the door stay ajar for some
minutes before you remove the
dishes.
The dishes are wet and dull.
The rinse aid dispenser is empty.
Fill the rinse aid dispenser with
rinse aid.
Limescale particles on the
dishes
The multitab function is activa- Activate the rinse aid dispenser.
ted (this function automatically deactivates the rinse aid dispenser).
24
What to do if…
Activating the rinse aid dispenser
1.
2.
3.
4.
5.
6.
Open the menu option.
Go to Settings .
Press the OK touchpad to open the submenu.
Go to Rinse aid and activate the rinse aid dispenser.
Press the OK touchpad.
Press the return touchpad to close the menu option.
Technical data
25
TECHNICAL DATA
Dimensions
Width
Height
Depth
Electrical connection
Voltage
Overall power
Fuse
Frequency
Water supply pressure
min.
max.
Capacity
Place settings
596 mm
818 - 898 mm
575 mm
220-240 V
2200 W
10 A
50 Hz
50 kPa (7 psi)
800 kPa (116 psi)
13
INSTALLATION
There should be a minimum
2mm gap between the top of
the dishwasher and
underside of bench top
The hose s hould not be
extended by more than
2 metres or water pumpout problems ma y occu r
Remove entire plastic
membrane from sink trap
spigot & fit drain hose to spigot
with clamp
Secure dishwasher with
brackets and screws provided
600 mm max.
300 mm min.
Gap on both sides should be
equal, & no greater than
5 mm per side.
•
K ickplate fixing screws
•
If floor is not level, adjust
levelling legs to suit
CAUTION!
Instructions for the installation, the furniture door and the water connection are in the
separate template that is provided with this appliance. Follow carefully these instructions.
WARNING!
Make sure that the mains plug is disconnected from the mains socket during installation.
26
Water connection
WARNING!
To prevent injury or damage, make sure that the appliance is under and adjacent safe structures. Use the supplied brackets to attach the appliance under the kitchen counter or to the
adjacent units.
Install the appliance under a kitchen counter.
If a repair is necessary, the appliance must be easily accessible for the engineer.
Put the appliance adjacent to a water tap and drain.
For the venting of the appliance only water hoses and mains cable openings are necessary.
The appliance has adjustable feet to allow the adjustment of its height.
Make sure that the water inlet hose, the drain hose and the mains cable are not bent or
squashed, when you insert the appliance.
Adjusting the level of the appliance
A correct adjustment of the level of the appliance allows the door to close and seal correctly.
If the door does not close correctly, loosen or tighten the adjustable feet to level the appliance.
WATER CONNECTION
Water inlet hose
Connect the inlet hose to a water tap with an external BSP thread spout of 3/4”.
For best washing performance it is recommended to connect the appliance to a cold water
supply.
Energy savings can be made by connecting the appliance to a Solar water system and using
economy options, however the water temperature must not exceed 60 °C.
Once connected the inlet hose to the water tap, turn the tap on and check that there are
no leaks.
Inlet water supply
• Water pressure: 800 kPa max - 50 kPa min.
• Water flow rate 10 L / minute min.
• If water pressure is in excess of 800 kPa, a pressure reducing valve should be used. Check
for leaks.
• If water temperature is in excess of 60 °C, a tempering valve should be used. Check for
leaks.
CAUTION!
Always use new hoses when you connect the appliance to the water mains. Old hoses must
not be used. The water inlet hose must be examined at an interval of twelve months for
deterioration and replaced if necessary.
The water pressure must be in the limits, refer to 'Technical data'.
Make sure that the local water authority gives you the average mains pressure in your area.
Make sure that the water inlet hose is not bent or squashed.
Fit the hose nut correctly to prevent water leaks.
Water connection
27
CAUTION!
Do not connect the appliance to new pipes or pipes that have been not used for a long
time. Let the water run for some minutes, then connect the inlet hose.
The water inlet hose is double-walled and has an inner mains cable and a safety valve. The
water inlet hose is under pressure only while the water is running. If there is a leak in the
water inlet hose, the safety valve interrupts the running water.
Be careful when you install the water inlet hose.
WARNING!
• The mains cable is in the double-walled inlet hose. Do not immerse the water inlet hose
or the safety valve in water.
• Do not attempt to shorten the inlet hose.
• If the water inlet hose or the safety valve is damaged, immediately turn off the power
and remove the mains plug from the mains socket.
• Only a qualified Service Engineer can replace the water inlet hose with safety valve.
WARNING!
Dangerous voltage
28
Water connection
In order to pass the safety valve through the kitchen cabinets, an opening of at
least 45 mm x 90 mm is needed.
Water drain hose
The highest point of the drain hose must be no more than 600 mm from the floor and must
have a continuous fall to the plumbing connection.
The drain hose can be lengthened using additional lengths and connectors. These must be
purchased from Electrolux Spare Parts. The extension length must not exceed 2 metres.
The drain hose must be free of obstructions.
Remove the sink plug when the appliance drains the water to prevent that the water goes
back into the appliance.
If you connect the water drain hose to a trap spigot under the sink, remove the plastic membrane.
If you do not remove the membrane, remaining
food can cause a blockage in the drain hose spigot.
The appliance has a security feature to prevent
dirty water going back into the appliance. If, the
spigot of the sink has a 'non-return valve', this
valve can cause the appliance to drain incorrectly.
Remove the non-return valve.
Water connection
CAUTION!
Make sure that the water couplings are tight to prevent water leakage.
Ensure that hoses are not bent or squashed under
or behind the appliance.
Once connected the inlet hose to the water tap,
turn the tap on and check that there are no leaks.
29
30
Electrical connection
ELECTRICAL CONNECTION
WARNING!
• The manufacturer accepts no liability for failure to observe the below safety precautions.
• Safety standards require the appliance to be earthed.
• Prior to using the appliance for the first time, ensure that the rated voltage and type of
supply on the rating plate match that of the supply where the appliance is to be installed.
• The fuse rating can be found on the rating plate and in 'Technical data'.
• Always plug the mains plug onto a correctly installed approved socket.
• Do not use multi-ways plugs, connectors and extension cables. This can constitute a fire
hazard through overheating.
• If necessary, have the domestic wiring system socket replaced. If the mains cable has to
be replaced, contact your local Customer Care centre.
• The mains plug must be accessible after the appliance has been installed.
• Never unplug the appliance by pulling on the cable. Always pull the plug.
• Test the appliance. Run a quick washing program and ensure that the appliance fills with
water, washes and drains with no leaks.
ENVIRONMENT CONCERNS
The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Discard the packaging materials in
the applicable container at the community waste disposal facilities.
WARNING!
Follow these instructions to discard the appliance:
• Pull the mains plug out of the socket.
• Cut off the mains cable and the mains plug and discard them.
• Discard the door catch. This prevents children from closing themselves inside the appliance and endangering their lives.
Old appliance
Make sure that the appliance goes to the applicable collection point for recycling.
Make sure that this appliance is discarded correctly. Inappropriate waste discard of the appliance causes negative consequences for the environment and human health.
For more information about the recycling of this appliance, contact your local city office,
your household waste disposal service or the shop where you purchased the appliance.
Warranty
31
WARRANTY
FOR SALES IN AUSTRALIA AND NEW ZEALAND
ALL AEG BRANDED APPLIANCES
This document sets out the terms and conditions of the product warranties for AEG Appliances. It is an important document. Please keep it with your proof of purchase documents in a safe place for future reference should you require service for your Appliance.
1. In this warranty
a) ‘acceptable quality’ as referred to in clause 10 of this warranty has the same
meaning referred to in the ACL;
b) ‘ACL’ means Trade Practices Amendment (Australian Consumer Law) Act (No.2)
2010;
c) ‘Appliance’ means any AEG product purchased by you accompanied by this document;
d) ‘ASC’ means AEG’ authorised serviced centres;
e) AEG is the brand controlled by Electrolux Home Products Pty Ltd of 163 O’Riordan
Street, Mascot, NSW 2020, ABN 51 004 762 341 in respect of Appliances purchased in Australia and Electrolux (NZ) Limited of 3-5 Niall Burgess Road, Mount
Wellington, in respect of Appliances purchased in New Zealand;
f) ‘major failure’ as referred to in clause 10 of this warranty has the same meaning
referred to in the ACL and includes a situation when an Appliance cannot be repaired or it is uneconomic for Electrolux, at its discretion, to repair an Appliance
during the Warranty Period;
g) ‘Warranty Period’ means:
– where the Appliance is used for personal, domestic or household use (i.e. normal
single family use) as set out in the instruction manual, the Appliance is warranted against manufacturing defects in Australia and New Zealand for 60 months,
following the date of original purchase of the Appliance;
– this Appliance is not designed for commercial use and therefore no warranty
applies in this case;
h) ‘you’ means the purchaser of the Appliance not having purchased the Appliance
for re-sale, and ‘your’ has a corresponding meaning.
2. This warranty only applies to Appliances purchased and used in Australia or New Zealand and is in addition to (and does not exclude, restrict, or modify in any way) any
non-excludable statutory warranties in Australia or New Zealand.
3. During the Warranty Period AEG or its ASC will, at no extra charge if your Appliance is
readily accessible for service, without special equipment and subject to these terms
and conditions, repair or replace any parts which it considers to be defective. AEG or
its ASC may use remanufactured parts to repair your Appliance. You agree that any
replaced Appliances or parts become the property of AEG. This warranty does not apply
to light globes, batteries, filters or similar perishable parts.
4. Parts and Appliances not supplied by AEG are not covered by this warranty.
32
Warranty
5.
You will bear the cost of transportation, travel and delivery of the Appliance to and
from AEG or its ASC. If you reside outside of the service area, you will bear the cost of:
a) travel of an authorised representative;
b) transportation and delivery of the Appliance to and from AEG or its ASC,
In all instances, unless the Appliance is transported by AEG or an AEG authorised representative, the Appliance is transported at the owner’s cost and risk while in transit to
and from AEG or its ASC.
6. Proof of purchase is required before you can make a claim under this warranty.
7. You may not make a claim under this warranty unless the defect claimed is due to
faulty or defective parts or workmanship. AEG is not liable in the following situations
(which are not exhaustive):
a) the Appliance is damaged by:
– accident
– misuse or abuse, including failure to properly maintain or service
– normal wear and tear
– power surges, electrical storm damage or incorrect power supply
– incomplete or improper installation
– incorrect, improper or inappropriate operation
– insect or vermin infestation
– failure to comply with any additional instructions supplied with the Appliance;
b) the Appliance is modified without authority from AEG in writing;
c) the Appliance’s serial number or warranty seal has been removed or defaced;
d) the Appliance was serviced or repaired by anyone other than AEG, an authorised
repairer or ASC.
8. This warranty, the contract to which it relates and the relationship between you and
AEG are governed by the law applicable where the Appliance was purchased. Where
the Appliance was purchased in New Zealand for business purposes the Consumer
Guarantee Act does not apply.
9. To the extent permitted by law, AEG excludes all warranties and liabilities (other than
as contained in this document) including liability for any loss or damage whether direct or indirect arising from your purchase, use or non use of the Appliance.
10. For Appliances and services provided by AEG in Australia, the Appliances come with a
guarantee by AEG that cannot be excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the Appliance repaired or replaced if the Appliance fails to be of acceptable quality and the
failure does not amount to a major failure. The benefits to you given by this warranty
are in addition to your other rights and remedies under a law in relation to the Appliances or services to which the warranty relates.
11. At all times during the Warranty Period, AEG shall, at its discretion, determine whether
repair, replacement or refund will apply if an Appliance has a valid warranty claim applicable to it.
33
12. For Appliances and services provided by AEG in New Zealand, the Appliances come
with a guarantee by AEG pursuant to the provisions of the Consumer Guarantees Act,
the Sale of Goods Act and the Fair Trading Act.
13. To enquire about claiming under this warranty, please follow these steps:
a) carefully check the operating instructions, user manual and the terms of this warranty;
b) have the model and serial number of the Appliance available;
c) have the proof of purchase (eg an invoice) available;
d) telephone the numbers shown below.
14. You accept that if you make a warranty claim, AEG and its ASC may exchange information in relation to you to enable AEG to meet its obligations under this warranty.
Important Notice
Before calling for service, please ensure that the steps listed in point 13 above have been
followed.
SERVICE AUSTRALIA
www.aeg.com/au
FOR SERVICE
or to find the address of your nearest state service centre in Australia
PLEASE CALL 1300 363 664
OR EMAIL customercare@aegaustralia.com.au
For the cost of a local call (Australia only)
FOR SPARE PARTS
or to find the address of your nearest state spare parts centre in Australia
PLEASE CALL 13 13 50
OR EMAIL customercare@aegaustralia.com.au
For the cost of a local call (Australia only)
SERVICE NEW ZEALAND
FOR SERVICE
or to find the address of your nearest authorised service centre in New Zealand
FREE CALL 0800 10 66 10
OR EMAIL customercare@electrolux.co.nz
(New Zealand only)
FOR SPARE PARTS
or to find the address of your nearest state spare parts centre in New Zealand
FREE CALL 0800 10 66 20
OR EMAIL customercare@electrolux.co.nz
(New Zealand only)
34
35
www.aeg.com/au
117934912-A-192012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising