Electrolux | ESF63020X | User manual | Electrolux ESF63020W User Manual

Electrolux ESF63020W User Manual
user manual
ESF 63020
We were thinking of you
when we made this product
electrolux 3
Welcome to the world of Electrolux
You’ve chosen a first class product from Electrolux,
which hopefully will provide you with lots of pleasure in
the future. Electrolux ambition is to offer a wide variety of
quality products that would make your life even more
comfortable. You can look at some examples on the
cover in this manual. But now it’s time to study this
manual and start using and enjoying the benefits from
your new machine. We promise that it’ll make your life a
little easier. Good luck!
The following symbols are used in this user manual:
Important information concerning your personal safety and information on
how to avoid damaging the appliance.
General information and tips
Environmental information
4 electrolux
Safety information
Product description
Control panel
First use
Set the water softener
Filling with dishwasher salt
Use of rinse aid
Adjusting the dosage of rinse aid
Daily use
Loading cutlery and dishes
Use of detergent
Select and start a washing
Unloading the dishwasher
Washing programmes
Care and cleaning
Something not working
Technical data
Consumption values
Hints for test institutes
Environment concerns
safety information electrolux 5
Safety information
In the interest of your safety and to
ensure the correct use, before installing and first using the appliance,
read this user manual carefully, including its hints and warnings. To
avoid unnecessary mistakes and accidents, it is important to ensure that
all people using the appliance are
thoroughly familiar with its operation and safety features. Save these
instructions and make sure that they
remain with the appliance if it is
moved or sold, so that everyone using it through its life will be properly
informed on appliance use and
Correct use
• This dishwasher is only intended for
washing household utensils suitable
for machine washing.
• Do not put any solvents in the
dishwasher. This could cause an explosion.
• Knives and other items with sharp
points must be loaded in the cutlery
basket with their points down or
placed in a horizontal position in the
upper basket.
• Only use products (detergent, salt and
rinse aid) suitable for dishwashers.
• Avoid opening the door whilst the appliance is in operation, hot steam may
• Do not take any dishes out of the
dishwasher before the end of the dishwashing cycle.
• After use, isolate the appliance from
the power supply and turn off the water supply.
• This product should be serviced only
by an authorised service engineer,
and only genuine spare parts should
be used.
• Under no circumstances should you
attempt to repair the machine yourself. Repairs carried out by inexperienced persons will cause injury or
serious malfunctioning. Contact your
local Service Force Centre. Always insist on genuine spare parts.
General safety
• Dishwasher detergents can cause
chemical burns to eyes, mouth and
throat. Could endanger life! Comply
with the safety instructions of the
dishwasher detergent manufacturer.
• The water in your dishwasher is not for
drinking. Detergent residues may still
be present in your machine.
• Ensure that the door of the
dishwasher is always closed when it is
not being loaded or unloaded. In this
way you will avoid anybody tripping
over the open door and hurting themselves.
• Do not sit or stand on the open door.
6 electrolux product description
Child safety
• This appliance is designed to be
operated by adults. Don’t allow children to use the dishwasher unsupervised.
• Keep all packaging well away from
children. There is risk of suffocation.
• Keep all detergents in a safe place out
of children’s reach.
• Keep children well away from the
dishwasher when the door is open.
• Check your dishwasher for any transport damage. Never connect a damaged machine. If your dishwasher is
damaged contact your supplier.
• All packaging must be removed before use.
• Any electrical and plumbing work required to install this appliance must be
carried out by a qualified and competent person.
• For safety reasons it is dangerous to
alter the specifications or attempt to
modify this product in any way.
• Never use the dishwasher if the electrical supply cable and water hoses
are damaged; or if the control panel,
work top or plinth area are damaged
such that the inside of the appliance is
freely accessible. Contact your local
Service Force centre, in order to avoid
• All sides of the dishwasher must never
be drilled to prevent damage to
hydraulic and electric components.
For electrical and water connection
carefully follow the instructions
given in specific paragraphs.
control panel electrolux 7
Product description
Upper basket
Water hardness dial
Salt container
Detergent dispenser
Rinse aid dispenser
Rating plate
Lower spray arm
Upper spray arm
8 electrolux control panel
Control panel
7 6
Programme guide
Programme knob
Start/cancel button
Delay start button
Indicator lights
On/Off indicator light
Programme marker
Indicator lights
Illuminates when the washing and rinsing phases are running.
Illuminates when the drying phase is
End of programme
Illuminates when the washing programme has ended. It also has added
functions of visual signalling as:
• the setting of the water softener,
• intervention of an alarm due to the
malfunction of the machine.
Salt refilling
Illuminates when special salt needs to
be filled.
first use electrolux 9
Indicator lights
Rinse aid
Illuminates when rinse aid needs to be
1) The salt and rinse aid indicator lights are never illuminated while a washing programme is running even
if filling with salt and rinse aid is necessary.
The salt indicator light on the control
panel can remain illuminated for 2-6
hours after the salt has been
replenished, assuming the
dishwasher remains switched on. If
you are using salts that take longer
to dissolve then this can take longer.
The function of the machine is not
Programme knob and On/Off
indicator light
• The selection of a washing programme occurs by turning the programme knob clockwise or anticlock-
wise, until the programme marker,
placed on the knob, corresponds with
the desired washing programme indicated on the control panel.
The On/Off indicator light illuminates
(position ON)
• To switch off the appliance turn the
programme knob until the programme marker corresponds with the
On/Off indicator light. The On/Off indicator light turns off (position OFF).
With the programme knob it is also
possible to set the level of the water
First use
Before using your dishwasher for the first
• Ensure that the electrical and water
connections comply with the installation instructions
• Remove all packaging from inside the
• Set the water softener
• Pour 1 litre of water inside the salt
container and then fill with dishwasher
• Fill the rinse aid dispenser
10 electrolux set the water softener
If you want to use combi detergent
tablets ("3 in 1", "4 in 1", "5 in 1"
etc... ) follow the instructions given
in "Use of detergent".
Set the water softener
The dishwasher is equipped with a water
softener designed to remove minerals
and salts from the water supply, which
would have a detrimental or adverse effect on the operation of the appliance.
The higher the content of these minerals
and salts, the harder your water is. Water
hardness is measured in equivalent
scales, German degrees (°dH), French
degrees (°TH) and mmol/l (millimol per
litre - international unit for the hardness
of water).
The softener should be adjusted according to the hardness of the water in your
area. Your local Water Authority can advise you on the hardness of the water in
your area.
The water softener must be set in
both ways: manually and
Adjusting the water
hardness setting
Water hardness
Use of salt
51 - 70
91 - 125
9,1 - 12,5
level 10
43 - 50
76 - 90
7,6 - 8,9
level 9
37 - 42
65 - 75
6,51 - 7,5
level 8
29 - 36
51 - 64
5,1 - 6,4
level 7
23 - 28
40 - 50
4,0 - 5,0
level 6
19 - 22
33 - 39
3,3 - 3,9
level 5
15 - 18
26 - 32
2,61 - 3,2
level 4
11 - 14
19 - 25
1,9 - 2,5
level 3
4 - 10
7 - 18
0,71 - 1,8
level 2
set the water softener electrolux 11
Adjusting the water
hardness setting
Water hardness
< 0,7
level 1
Use of salt
Setting manually
The dishwasher is factory set at position 2.
1. Open the dishwasher door.
2. Remove the lower basket from the
3. Turn the water hardness dial to position 1 or 2 (see table).
4. Replace the lower basket.
Setting electronically
The dishwasher is factory set at
level 5.
1. The dishwasher must be switched
Keep the start/cancel button
pressed and turn the programme
knob clockwise until the programme
marker corresponds with the first
washing programme.
2. Release the start/cancel button, the
On/Off and start/cancel indicator
lights start to flash indicating that you
have activated the water softener
setting function.
3. At the same time, the end of programme indicator light starts to flash.
The current level is indicated by the
number of flashes of the indicator
light end of programme and a pause
of about 3 seconds.
5 flashes, pause, 5 flashes, pause,
etc... = level 5
6 flashes, pause, 6 flashes, pause,
etc... = level 6
4. To change the level, press the start/
cancel button. Each time the button
is pressed the level changes.
if the current level is 5, by pressing
start/cancel button once, level 6 is
12 electrolux filling with dishwasher salt
if the current level is 10, by pressing
start/cancel button once, level 1 is
5. To memorize the operation, switch
off the dishwasher by returning the
programme knob to the Off position.
Filling with dishwasher salt
Only use salt specifically designed for
use in dishwashers. All other types of salt
not specifically designed for use in a
dishwasher, especially table salt, will
damage the water softener. Only fill with
salt just before starting one of the complete washing programmes. This will
prevent any grains of salt or salty water,
which may have been spilt, remaining on
the bottom of the machine for any period
of time, which may cause corrosion.
To fill:
1. Open the door, remove the lower
basket and unscrew the cap of the
salt container by turning it anticlockwise.
2. Pour 1 litre of water inside the
container (this is necessary only
before filling with salt for the first
time) .
3. Using the funnel provided, pour in
the salt until the container is full.
4. Replace the cap making sure that
there is no trace of salt on the screw
thread or on the gasket.
5. Replace the cap tightly turning it
clockwise until it stops with a click.
Do not worry if water overflows from
the unit when filling with salt, this is
quite normal.
use of rinse aid electrolux 13
The salt indicator light on the control
panel can remain illuminated for 2-6
hours after the salt has been
replenished, assuming the
dishwasher remains switched on. If
you are using salts that take longer
to dissolve then this can take longer.
The function of the machine is not
Use of rinse aid
Only use branded rinse aid for dishwashers.
Never fill the rinse aid dispenser with
any other substances (e.g.
dishwasher cleaning agent, liquid
detergent). This would damage the
Rinse aid ensures thorough rinsing,
and spot and streak free drying.
Rinse aid is automatically added
during the last rinse.
1. Open the container by pressing the
release button (A).
2. Add the rinse aid in the container.
The maximum level for filling is indicated by "max".
14 electrolux adjusting the dosage of rinse aid
The dispenser holds about 110 ml of
rinse aid, which is sufficient for between 16 and 40 dishwashing cycles, depending upon the dosage
3. Ensure that the lid is closed after every refill.
Clean up any rinse aid spilt during
filling with an absorbent cloth to
avoid excess foaming during the
next wash.
Adjusting the dosage of rinse aid
According to the finish and drying
results obtained, adjust the dose of
rinse aid by means of the 6 position
selector (position 1 minimum dosage, position 6 maximum dosage).
The dose is factory set in position 4.
Increase the dose if there are drops
of water or lime spots on the dishes
after washing.
Reduce it if there are sticky whitish
streaks on the dishes or a bluish film
on glassware or knife blades.
Daily use
• Check if it’s necessary to refill with
dishwasher salt or rinse aid.
• Load cutlery and dishes into the
• Fill with dishwasher detergent.
• Select a wash programme suitable for
the cutlery and dishes.
• Start the wash programme.
loading cutlery and dishes electrolux 15
Loading cutlery and dishes
Sponges, household cloths and any object that can absorb water may not be
washed in the dishwasher.
• Before loading the dishes, you should:
– Remove all left over food and debris.
– Soften remnants of burnt food in
• When loading the dishes and cutlery,
please note:
– Dishes and cutlery must not impede
the rotation of the spray arms.
– Load hollow items such as cups,
glasses, pans, etc. with the opening
downwards so that water cannot
collect in the container or a deep
– Dishes and items of cutlery must
not lie inside one another, or cover
each other.
– To avoid damage to glasses, they
must not touch.
– Lay small objects in the cutlery basket.
• Plastic items and pans with non stick
coatings have a tendency to retain
water drops; these items will not dry
as well as porcelain and steel items.
• Light items (plastic bowls etc.) must
be loaded in the upper basket and arranged so they do not move.
For washing in the dishwasher the following cutlery and dishes
are not suitable:
are of limited suitability:
• Cutlery with wooden, horn, china or • Only wash stoneware in the
mother-of-pearls handles.
dishwasher if it is specially marked as
being dishwasher-safe by the
• Plastic items that are not heat resistmanufacturer.
Glazed patterns may fade if machine
• Older cutlery with glued parts that are
washed frequently.
not temperature resistant.
• Silver and aluminium parts have a
• Bonded cutlery items or dishes.
tendency to discolour during wash• Pewter or copper items.
ing: Residues, e.g. egg white, egg
• Lead crystal glass.
yolk and mustard often cause disco• Steel items prone to rusting.
louring and staining on silver. There• Wooden platters.
fore always clean left-overs from silver
immediately, if it is not to be washed
• Items made from synthetics fibres.
straight after use.
16 electrolux loading cutlery and dishes
The lower basket
The lower basket is designed to take
saucepan, lids, plates, salad bowls, cutlery ect.
Service dishes and large lids should be
arranged around the edge of the basket,
ensuring that the spray arms can turn
The cutlery basket
Long bladed knives stored in an upright position are a potential hazard.
Long and/or sharp items of cutlery
such as carving knives must be
positioned horizontally in the upper
basket. Take care when loading or
unloading sharp items such as knives.
Forks and spoons should be placed in
the removable cutlery basket with the
handles facing downwards and the knives with their handles facing upwards.
If the handles protrude from the bottom
of the basket, obstructing the lower
spray arm, load the cutlery with the handles facing upwards. Mix spoons with
other cutlery to prevent them from sticking together.
For best results we recommend you to
use the cutlery grid. If the size and dimensions of the cutlery do not allow the
use of the grid, they can be easily removed.
loading cutlery and dishes electrolux 17
Glasses with long stems can be placed
upside down in the cup racks.
For taller items, the cup racks can be
folded upwards.
The upper basket
The upper basket is designed for plates
(dessert plates, saucers, dinner plates of
up to 24 cm in diameter), salad bowls,
cups and glasses
Arrange items on and underneath the
cup racks so that water can reach all
Before closing the door, ensured
that the spray arms can rotate
Adjusting the height of the upper
If washing very large plates you can load
them in the lower basket after moving
the upper basket to the higher position.
Maximum height of the dishes in:
the upper basket
the lower basket
With upper basket raised 20 cm
31 cm
With upper basket lowered
27 cm
24 cm
To move to the higher position proceed as follows:
1. Move the front runner stops (A) of the
upper basket outwards and slide the
basket out.
18 electrolux use of detergent
2. Refit the basket in the higher position
and replace the stops (A) in their
original position.
When the upper basket is raised you
will not be able to use the cup racks.
After loading your machine always
close the door, as an open door can
be a hazard.
Use of detergent
Only use detergents specifically designed for use in dishwashers.
Please observe the manufacturer’s
dosing and storage recommendations as stated on the detergent
Using no more than the correct
amount of detergent contributes to
reducing pollution.
Fill with detergent
1. Open the lid.
2. Fill the detergent dispenser (1) with
detergent. The marking indicates the
dosing levels:
20 = approximately 20 g of detergent
30 = approximately 30 g of detergent.
use of detergent electrolux 19
Detergent tablets from different
manufactures dissolve at different
rates. For this reason, some detergent tablets do not attain their full
cleaning power during short washing programmes. Therefore, please
use long washing programmes
when using detergent tablets, to ensure the complete removal of detergent residuals.
Use of combi detergent tablets
3. All programmes with prewash need
an additional detergent dose (5/10 g)
that must be placed in the prewash
detergent chamber (2).
This detergent will take effect during
the prewash phase.
When using detergent tablets; place
the tablet in compartment (1)
4. Close the lid and press until it locks
in place.
Detergent tablets
These products are detergents with a
combined cleaning, rinsing and salt
functions. They can also contain other
different agents depending on which
kind of tablets you choose («3 in 1», «4
in 1», «5 in 1» etc...).
1. Check whether these detergents are
suitable for your water hardness. See
the manufacturers instructions.
2. Select the lowest setting for water
hardness and rinse aid dosage.
3. Before the start of the washing programme put the combi detergent
tablet in the detergent dispenser.
The refilling of the salt container and
the rinse aid dispenser are no longer
necessary. In this case the rinse aid
indicator light will always remain illuminated when the machine is
switched on (not all dishwasher
models are foreseen with rinse aid
indicator light).
20 electrolux select and start a washing programme
If the drying results are not
satisfactory we recommend that
1. Fill up the rinse aid dispenser
with rinse aid.
2. Set the rinse aid dosage to position 2.
1. Fill up the dispensers for salt and
rinse aid again.
2. Adjust the water hardness setting to
the highest setting and perform
washing programme without loading
any dishes.
3. Adjust the water hardness setting
according to the hardness of the water in your area.
4. Adjust the rinse aid dosage.
If you decide to turn back to the use
of the standard detergent system
we advise that you:
Select and start a washing programme
1. Check that the baskets have been
loaded correctly and that the spray
arms are free to rotate
2. Check that the water tap is opened
3. Close the dishwasher’s door.
4. Turn the programme knob until the
programme marker corresponds
with the desired programme (see
"Washing programmes" chart).
– The On/Off indicator light illuminates.
– The indicator lights of the phases
foreseen for the programme start
5. Press the start/cancel button, the
programme starts automatically and
the start/cancel indicator light illuminates.
– As soon as the programme starts,
the phase indicator lights turn off
except for the indicator light for the
phase in progress which will remain lit with a static light.
During the running of the programme, it is not possible to change
the selection made by turning the
programme knob in correspondence of another programme or the
Off position. If you want to change
the running programme you must
cancel the selection made (see
"Cancel a washing programme in
Setting and starting the
programme with "delay start"
• Allows the start of the programme to
be delayed by 3 hours.
select and start a washing programme electrolux 21
1. After having selected the washing
programme, press the delay start
– The corresponding indicator light
2. Press the start/cancel button, the
countdown of the delay start begins
– The phase indicator lights turn off.
– The opening of the door will not
modify or interrupt the countdown.
– Once the delay start has elapsed
the washing programme will start
automatically, the delay start indicator light turns off while the indicator light of the phase in progress
Cancelling the "delay start"
• Press the start/cancel button for
about 5 seconds, the indicator lights
of start/cancel and delay start buttons turn off while the indicator lights
of the phases start flashing.
To start the selected washing programme press the start/cancel button.
The washing programme or the
countdown of the delay start will begin only after having pressed the
start/cancel button. Until that moment it is possible to modify the selection made.
Interrupt or cancel a washing programme in progress ONLY if it’s
absolutely necessary. Attention! Hot
steam may escape when the door is
opened. Open the door carefully.
Interrupt a washing programme in
• Open the dishwasher door; the programme will stop. Close the door; the
programme will start from the point at
which it was interrupted.
Cancel a washing programme in
• Press the start/cancel button for
about 5 seconds. The start/cancel indicator light turns off and the phase
indicator lights are flashing. The running programme has been cancelled
and it is now possible to set a new
washing programme or switch off the
machine. If a new washing programme is to be selected, check that
there is detergent in the detergent
End of the washing programme
• The dishwasher will automatically
• The end of programme indicator
light will illuminate.
1. Switch off the dishwasher by returning the programme knob to the Off
position. The On/Off indicator light
turns off.
2. Open the dishwasher’s door, leave it
ajar and wait a few minutes before
removing the dishes; in this way they
22 electrolux unloading the dishwasher
will be cooler and the drying will be
Unloading the dishwasher
• Hot dishes are sensitive to knocks.
The dishes should therefore be allowed to cool down before removing
from the appliance.
• Empty the lower basket first and then
the upper one; this will avoid water
dripping from the upper basket onto
the dishes in the lower one.
• Water may appear on the sides and
the door of the dishwasher as the
stainless steel will eventually become
cooler than the dishes.
When the washing programme has
finished, it is recommended that the
dishwasher is unplugged and the
water tap turned off.
Washing programmes
Degree of soil
Type of load
Programme description
Heavy soil
Crockery, cutlery,
pots and pans
Main wash up to
2 intermediate rinses
Final rinse
Normal soil
Crockery, cutlery,
pots and pans
Main wash up to
2 intermediate rinses
Final rinse
Intensive 70°
Normal 65°
care and cleaning electrolux 23
Degree of soil
Type of load
Programme description
Normal or light soil Crockery and cut- Main wash up to
Final rinse
Normal soil
Eco 50°
Rinse and Hold
Crockery and cut- Prewash
Main wash up to
1 intermediate
Final rinse
1 cold rinse (to
Partial load (to be completed later in the avoid food scraps
from sticking
This programme
does not require
the use of detergent.
1) Ideal for washing a partially loaded dishwasher. This is the perfect daily programme, made to meet
the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery.
2) Test programme for test institutes.
Care and cleaning
Cleaning the filters
The filters must be checked and cleaned
from time to time. Dirty filters will degrade the washing result.
Before cleaning the filters ensure
that the machine is switched off.
1. Open the door, remove the lower
2. The dishwasher filter system comprises a coarse filter (A), a microfilter (B)
and a flat filter. Unlock the filter system using the handle on the microfilter.
24 electrolux care and cleaning
Turn the handle about 1/4 a turn anticlockwise and remove the filter system.
4. Take hold of the coarse filter (A) by
the handle with the hole and remove
from the microfilter (B).
5. Clean all filters thoroughly under running water.
6. Remove the flat filter from the base
of the washing compartment and
clean both faces thoroughly.
Put the flat filter back in the base of
the washing compartment and ensure that it fits perfectly under the
two guides (C).
8. Place the coarse filter (A) in the microfilter (B) and press together.
9. Put the filter combination in place
and lock by turning the handle clockwise to the stop. During this process
ensure that the flat filter does not
protrude above the base of the
washing compartment.
care and cleaning electrolux 25
Prolonged periods of nonoperation
NEVER use the dishwasher without
filters. Incorrect repositioning and
fitting of the filters will produce poor
washing results and may result in
damage to the appliance.
Cleaning the spray arms
If you are not using the machine for any
prolonged period of time you are advised to:
1. Unplug the appliance and then turn
off the water.
2. Leave the door ajar to prevent the
formation of any unpleasant smells.
3. Leave the inside of the machine
NEVER try to remove the spray
Frost precautions
If residues of soil have clogged the holes
in the spray arms, remove them with a
cocktail stick.
Avoid placing the machine in a location
where the temperature is below 0°C. If
this is unavoidable, empty the machine,
close the appliance door, disconnect the
water inlet pipe and empty it.
External cleaning
Clean the external surfaces of the machine and control panel with a damp soft
cloth. If necessary use only neutral detergents. Never use abrasive products,
scouring pads or solvent (acetone, trichloroethylene etc....).
Internal cleaning
Ensure that the seals around the door,
the detergent and rinse aid dispensers
are cleaned regularly with a damp cloth.
We recommend every 3 months to run
the wash programme for heavy soiled
dishes using detergent but without
Moving the machine
If you have to move the machine (moving
house etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with
the hoses.
Avoid over tilting the machine during
26 electrolux something not working
Something not working
The dishwasher will not start or stops
during operation.
Certain problems are due to the lack of
simple maintenance or oversights,
which can be solved with the help of the
indications described in the chart, without calling out an engineer.
Switch off the dishwasher, open the
door and carry out the following suggested corrective actions.
Fault code and malfunction
Possible cause and solution
• continuous flashing of the start/cancel indicator light
• 1 flash of the end of programme indicator light
The dishwasher does not fill with water
• The water tap is blocked or furred
with limescale
Clean the water tap
• The water tap is turned off
Turn the water tap on
• The filter (where present) in the threaded hose fitting at the water inlet valve
is blocked
Clean the filter in the threaded hose
• The water inlet hose has not been
correctly laid or it is bent or squashed
Check the water drain hose connection
• continuous flashing of the start/cancel indicator light
• 2 flashes of the end of programme
indicator light
The dishwasher will not drain
• The sink spigot is blocked
Clean out the sink spigot
• The water drain hose has not been
correctly laid or it is bent or squashed
Check the water drain hose connection
• continuous flashing of the start/can- • Anti-flood device is activated
Close the water tap and contact your
cel indicator light
• 3 flashes of the end of programme local Service Force Center.
indicator light
something not working electrolux 27
Fault code and malfunction
• The programme does not start
Once these checks have been carried
out, switch on the appliance: the programme will continue from the point at
which it was interrupted.
If the malfunction or fault code reappears contact the Service Force Centre.
For other fault codes not described in
the above chart, please contact your local Service Force Centre, quoting the
model (Mod.), product number (PNC)
and serial number (S.N.).
Possible cause and solution
• The dishwasher’s door has not been
properly closed
Close the door
• The main plug is not plugged in
Insert the main plug
• The fuse has blown out in the household fuse box
Replace the fuse
• Delay start has been set
If dishes are to be washed immediately,
cancel the delay start
This information can be found on the rating plate located on the side of the
dishwasher door.
So that you always have these numbers
at hand, we recommend you to make a
note of them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . .
PNC :. . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . .
28 electrolux something not working
The wash results are not satisfactory
The dishes are not clean
• The wrong washing programme has
been selected.
• The dishes are arranged in such a
way as to stop water reaching all
parts of the surface. The baskets
must not be overloaded.
• The spray arms do not rotate freely
due to incorrect arrangement of the
• The filters in the base of the washing
compartment are dirty or incorrectly
• Too little or no detergent has been
• Where there are limescales deposits
on the dishes; the salt container is
empty or the incorrect level of the water softener has been set.
• The drain hose connection is not correct.
• The salt container cap is not properly
The dishes are wet and dull
• Rinse aid was not used.
• The rinse aid dispenser is empty.
There are streaks, milky spots or a blu- • Decrease rinse aid dosing.
ish coating on glasses and dishes
Water drops have dries onto glasses
and dishes
If after all these checks, the problem persists, contact your local Service Force
• Increase rinse aid dosing.
• The detergent may be the cause.
Contact the detergent manufacturer’s consumer care line.
technical data electrolux 29
Technical data
Width x Height x Depth
60,0 x 85,0 x 61,0
Electrical connection
Voltage - Overall power Fuse
Information on the electrical connection is given on the
rating plate on the inner edge of the dishwasher’s
Water supply pressure
Minimum - Maximum
0,05 - 0,8
place settings
Max. weight
Noise level
Consumption values
Consumption values
Programme duration (in minutes)
Energy consumption (in
Water (litres)
Quick 30'
ECO (Test pro140
gramme for Test
Rinse and Hold
The consumption values are intended as a guide and depends on the
pressure and the temperature of the
water and also by the variations of
the power supply and the amount of
30 electrolux hints for test institutes
Hints for test institutes
Testing in accordance with EN 60704
must be carried out with appliance fully
loaded and using the test programme
(see "Consumption values").
Test in accordance with EN 50242 must
be carried out when the salt container
and rinse aid dispenser have been filled
with salt and rinse aid respectively and
using the test programme (see
"Consumption values").
Full load: 12 standard place settings
Amount of detergent required
5 g + 25 g (Type B)
Rinse aid setting
position 4 (Type III)
Lower basket
Cutlery basket
installation electrolux 31
cup racks: position A
Upper basket
Any electrical and/or plumbing work
required to install this appliance
should be carried out by a qualified
electrician and/or plumber or competent person.
Remove all packaging before positioning the machine.
If possible, position the machine next to
a water tap and a drain.
Fitting under a counter (kitchen
worktop or sink)
By removing the machine’s worktop,
you can install it under a close fitting sink
unit or a pre-existing top, providing the
dimensions of the recess correspond to
those shown in the picture.
Proceed as follows:
32 electrolux installation
• Remove the machine’s worktop by
unscrewing the two rear retaining
screws, pull the worktop from the
back of the machine and slide out the
front slots, lifting the worktop.
• Insert the machine after adjusting the
levelling with the adjustable feet.
When inserting the machine, ensure that
the water inlet and drain hoses are not
kinked or squashed.
During all operations that involve
accessibility to internal components the
dishwasher has to be unplugged.
Be sure that once the appliance has
been installed, it is easily accessible for
the service engineer in the event that a
repair is required.
If the dishwasher is later used as a freestanding appliance, the original worktop
must be re-mounted.
The plinth on free-standing appliances is
not adjustable.
Good levelling is essential for correct
closure and sealing of the door. When
the appliance is correctly levelled, the
door will not catch on either side of the
cabinet. If the door does not close
correctly, loosen or tighten the adjustable feet until the machine is perfectly
Water supply connections
This dishwasher may be fed with either
hot (max. 60°) or cold water. Nevertheless we advise you a cold water supply.
A hot water supply is not always efficient
with very soiled crockery as it shortens
the washing programmes a lot.
For making the connection itself, the
coupling nut fitted to the machine’s supply hose is designed to screw onto a
3/4" gas thread spout or to a purpose
made quick-coupling tap such as the
The water pressure must be within the
limits given in the "Technical specifications". Your local Water Authority will advise you on the average mains pressure
in your area.
The water inlet hose must not be kinked,
crushed, or entangled when it is being
The dishwasher features fill and drain
hoses which can be turned either to the
left or the right to suit the installation by
means of the locknut.
The locknut must be correctly fitted
to avoid water leaks.
(Attention! NOT all models of dishwashers have fill and drain hoses provided
with locknut. In this case, this kind of
facility is not possible). If the machine is
connected to new pipes or pipes which
have not been used for a long time, you
should run the water for a few minutes
before connecting the inlet hose.
DO NOT use connection hoses
which have previously been used for
an old appliance.
installation electrolux 33
This appliance has been fitted with
safety features which will prevent
the water used in the appliance from
returning back into the drinking water system. This appliance complies
with the applicable plumbing regulations.
Water outlet hose connection
The end of the drain hose can be connected in the following ways:
1. To the sink outlet spigot, securing it
to the underside of the work surface.
This will prevent waste water from
the sink running into the machine.
2. To a stand pipe provided with venthole, minimum internal diameter 4
The waste connection must be at a
height of between 30 cm (minimum) and
100 cm (maximum) from the bottom of
the dishwasher.
The drain hose can face either to the
right or left of the dishwasher.
Ensure the hose is not bent or squashed
as this could prevent or slow down the
discharge of water.
The sink plug must not be in place when
the machine is draining as this could
cause the water to syphon back into the
If you use a drain hose extension it must
be no longer than 2 metres and its internal diameter must be no smaller than the
diameter of the hose provided.
Likewise the internal diameter of the
couplings used for connections to the
waste outlet must be no smaller than the
diameter of the hose provided.
When connecting the drain hose to an
under sink trap spigot, the entire plastic membrane (A) must be removed.
Failure to remove all the membrane will
result in food particles building up over
time eventually blocking the dishwasher
drain hose spigot.
Our appliances are supplied with a
security device to protect against
the return of dirty water back into
the machine. If the spigot of your
sink has a "no return valve" incorporated this can prevent the correct
draining of your dishwasher. We
therefore advise you to remove it.
34 electrolux environment concerns
Electrical connection
Safety standards require the appliance to be earthed.
Prior to using the appliance for the
first time, ensure that the rated voltage and type of supply on the rating
plate match that of the supply where
the appliance is to be installed.
The fuse rating is also to be found on
the rating plate.
Always plug the mains plug into a
correctly installed shockproof
socket. Multi-way plugs, connectors and extension cables must not
be used.
This could constitute a fire hazard
through overheating.
If necessary, have the domestic wiring system socket replaced. In case
that the electrical cable has to be
replaced, contact your local Service
Force centre.
The plug must be accessible after
the appliance has been installed.
Never unplug the appliance by pulling on the cable. Always pull the
The manufacturer accepts no
liability for failure to observe the
above safety precautions.
Environment concerns
Packaging material
The packaging materials are
environmentally friendly and can be recycled. The plastic components are
identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging materials in the appropriate
container at the community waste
disposal facilities.
When a unit is no longer being used:
• Pull the plug out of the socket.
• Cut off the cable and plug and dispose of them.
• Dispose of the door catch. This
prevents children from trapping
themselves inside and endangering their lives.
The symbol
on the product or on its
packaging indicates that this product
may not be treated as household waste.
Instead it should be taken to the appropriate collection point for the recycling of
electrical and electronic equipment. By
ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of
environment concerns electrolux 35
this product, please contact your local
council, your household waste disposal
service or the shop where you purchased the product.
36 electrolux
electrolux 37
38 electrolux
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF