Electrolux | ESI66010X | User manual | Electrolux ESI66010X User Manual

user manual
dishwasher
ESI 66010
We were thinking of you
when we made this product
electrolux 3
Welcome to the world of Electrolux
You’ve chosen a first class product from Electrolux,
which hopefully will provide you with lots of pleasure in
the future. Electrolux ambition is to offer a wide variety of
quality products that would make your life even more
comfortable. You can look at some examples on the
cover in this manual. But now it’s time to study this
manual and start using and enjoying the benefits from
your new machine. We promise that it’ll make your life a
little easier. Good luck!
117978490 - 102007
The following symbols are used in this user manual:
Important information concerning your personal safety and information on
how to avoid damaging the appliance.
General information and tips
Environmental information
4 electrolux
Contents
Safety information
Product description
Control panel
First use
Set the water softener
Use of dishwasher salt
Use of rinse aid
Daily use
Load cutlery and dishes
Use of detergent
Multi-tab function
Select and start a washing
programme
5
7
8
10
10
12
13
14
15
19
20
Unloading the dishwasher
Washing programmes
Care and cleaning
What to do if...
Technical data
Hints for test institutes
Installation
Water connection
Electrical connection
Environment concerns
24
24
26
28
31
31
32
33
36
36
22
Subject to change without notice
safety information electrolux 5
Safety information
In the interest of your safety and to
ensure the correct use, before installing and first using the appliance,
read this user manual carefully, including its hints and warnings. To
avoid unnecessary mistakes and accidents, it is important to ensure that
all people using the appliance are
thoroughly familiar with its operation and safety features. Save these
instructions and make sure that they
remain with the appliance if it is
moved or sold, so that everyone using it through its life will be properly
informed on appliance use and
safety.
Correct use
• This dishwasher is only intended for
washing household utensils suitable
for machine washing.
• Do not put any solvents in the
dishwasher. This could cause an explosion.
• Knives and other items with sharp
points must be loaded in the cutlery
basket with their points down or
placed in a horizontal position in the
upper basket.
• Only use products (detergent, salt and
rinse aid) suitable for dishwashers.
• Avoid opening the door whilst the appliance is in operation, hot steam may
escape.
• Do not take any dishes out of the
dishwasher before the end of the
washing cycle.
• After use, isolate the appliance from
the power supply and turn off the water supply.
• This product should be serviced only
by an authorized service engineer,
and only genuine spare parts should
be used.
• Under no circumstances should you
attempt to repair the machine yourself. Repairs carried out by inexperienced persons could cause injury or
serious malfunctioning. Contact your
local Service Force Centre. Always insist on genuine spare parts.
General safety
• Dishwasher detergents can cause
chemical burns to eyes, mouth and
throat. Could endanger life! Comply
with the safety instructions of the
dishwasher detergent manufacturer.
• The water in your dishwasher is not for
drinking. Detergent residues may still
be present in your machine.
• Ensure that the door of the
dishwasher is always closed when it is
not being loaded or unloaded. In this
way you will avoid anybody tripping
over the open door and hurting themselves.
• Do not sit or stand on the open door.
6 electrolux safety information
Child safety
• This appliance is designed to be
operated by adults. Do not allow children to use the dishwasher unsupervised.
• Keep all packaging well away from
children. There is a risk of suffocation.
• Keep all detergents in a safe place out
of children’s reach.
• Keep children well away from the
dishwasher when the door is open.
Installation
• Check your dishwasher for any transport damage. Never connect a damaged machine. If your dishwasher is
damaged contact your supplier.
• All packaging must be removed before use.
• Any electrical and plumbing work required to install this appliance must be
carried out by a qualified and competent person.
• For safety reasons it is dangerous to
alter the specifications or attempt to
modify this product in any way.
• Never use the dishwasher if the electrical supply cable and water hoses
are damaged; or if the control panel,
work top or plinth area are damaged
such that the inside of the appliance is
freely accessible. Contact your local
Service Force centre, in order to avoid
hazard.
• All sides of the dishwasher must never
be drilled to prevent damage to
hydraulic and electric components.
For electrical and water connection
carefully follow the instructions
given in the specific paragraphs.
product description electrolux 7
Product description
1.
2.
3.
4.
5.
Upper basket
Water hardness dial
Salt container
Detergent dispenser
Rinse aid dispenser
6.
7.
8.
9.
Rating plate
Filters
Lower spray arm
Upper spray arm
8 electrolux control panel
Control panel
1.
2.
3.
4.
5.
6.
On/Off button
Programme selection buttons
Delay start button
Digital display
Indicator lights
Function buttons
The digital display
The digital display indicates:
• the level of hardness to which the water softener is set,
• the approximate remaining time of the
running programme,
• activation/deactivation of the rinse aid
dispenser (ONLY with "Multitab function active"),
• the end of a washing programme (a
zero will appear in the digital display),
• the countdown for the delay start,
• fault codes concerning malfunction of
the dishwasher.
control panel electrolux 9
Function buttons
The following functions can be set using
these buttons:
• setting the water softener level,
• cancelling a washing programme or a
delay start in progress,
• activation/deactivation of the Multitab
function,
• activation/deactivation of the rinse aid
dispenser when Multitab function is
active.
Indicator lights
Programme in progress
Illuminates when a washing programme
is set and remains illuminated for all the
duration of the washing programme.
Turns off when the washing programme
has ended.
End
Illuminates when a washing programme
has ended.
Multitab function
Indicates the activation/deactivation of
the "Multitab function" (see "Multitab
function").
Salt
Illuminates when the special salt has run
out.
1)
Rinse aid
1)
Illuminates when the rinse aid has run
out.
1) The salt and rinse aid indicator lights are never illuminated while a washing programme is running even
if filling with salt and/or rinse aid is necessary.
Setting mode
Press the On/Off button; if ALL programme button lights are illuminated the
appliance is in setting mode.
Always remember that when performing the following operations:
– selecting a washing programme,
– setting the water softener level,
– activating/deactivating the rinse
aid,
the appliance MUST be in setting
mode.
Press the On/Off button; if a programme
button light is illuminated the last performed or selected programme is still
set. In this case, to return to setting
10 electrolux first use
mode, the programme has to be cancelled.
To cancel a set programme or a
programme in progress
Simultaneously press and hold the two
Cancel buttons (function buttons B and
C) until all the programme button lights
illuminate. The programme has been
cancelled and the machine is now in setting mode.
First use
Before using your dishwasher for the first
time:
• Ensure that the electrical and water
connections comply with the installation instructions
• Remove all packaging from inside the
appliance
• Set the water softener level
• Pour 1 litre of water into the salt
container and then fill with dishwasher
salt
• Fill the rinse aid dispenser
If you want to use combi detergent
tablets such as: ''3 in 1'', ''4 in 1'', ''5
in 1'' etc... set the Multitab function.
(See ''Multitab function'').
Set the water softener
The dishwasher is equipped with a water
softener designed to remove minerals
and salts from the water supply, which
would have a detrimental or adverse effect on the operation of the appliance.
The higher the content of these minerals
and salts, the harder your water is. Water
hardness is measured in equivalent
scales, German degrees (dH°), French
degrees (°TH) and mmol/l (millimol per
litre - international unit for the hardness
of water).
The softener should be adjusted according to the hardness of the water in your
area. Your local Water Authority can advise you on the hardness of the water in
your area.
The water softener must be set in
two ways: manually, using the water
hardness dial and electronically.
set the water softener electrolux 11
Adjusting the water hardness
setting
°dH
°TH
mmol/l
manually
electronically
Use
of
salt
51 - 70
91 - 125
9,1 - 12,5
2
level 10
yes
43 - 50
76 - 90
7,6 - 9,0
2
level 9
yes
37 - 42
65 - 75
6,5 - 7,5
2
level 8
yes
29 - 36
51 - 64
5,1 - 6,4
2
level 7
yes
23 - 28
40 - 50
4,0 - 5,0
2
level 6
yes
19 - 22
33 - 39
3,3 - 3,9
2
level 5
yes
15 - 18
26 - 32
2,6 - 3,2
1
level 4
yes
11 - 14
19 - 25
1,9 - 2,5
1
level 3
yes
4 - 10
7 - 18
0,7 - 1,8
1
level 2
yes
<4
<7
< 0,7
1
level 1
no
Water hardness
Setting manually
Setting electronically
The dishwasher is factory set at position 2.
The dishwasher is factory set at
level 5.
1. Open the dishwasher door.
2. Remove the lower basket from the
dishwasher.
3. Turn the water hardness dial to position 1 or 2 (see chart).
4. Replace the lower basket.
1. Press the On/Off button. The
dishwasher must be in setting mode.
2. Simultaneously press and hold function buttons B and C, until the lights
of function buttons A, B and C start
flashing.
3. Press function button A, the lights of
function buttons B and C turn off
while the light of function button A
continues to flash. The current level
shows on the digital display.
Examples:
displayed = level 5
displayed = level 10
12 electrolux use of dishwasher salt
4. To change the level, press function
button A. Each time the button is
pressed the level changes. (For the
selection of the new level see the
chart)..
Examples: If the current level is 5, by
pressing function button A once,
level 6 is selected. if the current level
is 10, by pressing function button A
once, level 1 is selected.
5. To memorise the operation, switch
off the dishwasher by pressing the
On/Off button.
Use of dishwasher salt
Only use salt specifically designed for
use in dishwashers. All other types of salt
not specifically designed for use in a
dishwasher, especially table salt, will
damage the water softener. Only fill with
salt just before starting one of the complete washing programmes. This will
prevent any grains of salt or salty water,
which may have been spilt, remaining on
the bottom of the machine for any period
of time, which may cause corrosion.
To fill:
1. Open the door, remove the lower
basket and unscrew the cap of the
salt container by turning it anticlockwise.
2. Pour 1 litre of water inside the
container (this is necessary only
before filling with salt for the first
time) .
3. Using the funnel provided, pour in
the salt until the container is full.
4. Replace the cap making sure that
there is no trace of salt on the screw
thread or on the gasket.
5. Replace the cap tightly turning it
clockwise until it stops with a click.
Do not worry if water overflows from
the unit when filling with salt, this is
quite normal.
use of rinse aid electrolux 13
The salt indicator light on the control
panel can remain illuminated for 2-6
hours after the salt has been
replenished, assuming the
dishwasher remains switched on. If
you are using salt that takes longer
to dissolve then this can take longer.
The operation of the machine is not
affected.
Use of rinse aid
Only use branded rinse aid for dishwashers.
Never fill the rinse aid dispenser with
any other substances (e.g.
dishwasher cleaning agent, liquid
detergent). This would damage the
appliance.
Rinse aid ensures thorough rinsing,
and spot and streak free drying.
Rinse aid is automatically added
during the last rinse.
1. Open the container by pressing the
release button (A).
2. Add the rinse aid in the container.
The maximum level for filling is indicated by "max".
14 electrolux daily use
The dispenser holds about 110 ml of
rinse aid, which is sufficient for between 16 and 40 washing cycles,
depending upon the dosage setting.
3. Ensure that the lid is closed after every refill.
Increase the dose if there are drops of
water or lime spots on the dishes after
washing.
Reduce it if there are sticky whitish
streaks on the dishes or a bluish film on
glassware or knife blades.
Clean up any rinse aid spilt during
filling with an absorbent cloth to
avoid excess foaming during the
next wash.
According to the finish and drying results
obtained, adjust the dose of rinse aid by
means of the 6 position selector (position 1 minimum dosage, position 6 maximum dosage).
The dose is factory set in position 4.
Daily use
• Check if it’s necessary to refill with
dishwasher salt or rinse aid.
• Load cutlery and dishes into the
dishwasher.
• Fill with dishwasher detergent.
• Select a wash programme suitable for
the cutlery and dishes.
• Start the wash programme.
Helpful hints and tips
Sponges, household cloths and any object that can absorb water may not be
washed in the dishwasher.
• Before loading the dishes, you should:
– Remove all left over food and debris.
– Soften remnants of burnt food in
pans
load cutlery and dishes electrolux 15
• When loading the dishes and cutlery,
please note:
– Dishes and cutlery must not impede
the rotation of the spray arms.
– Load hollow items such as cups,
glasses, pans, etc. with the opening
downwards so that water cannot
collect in the container or a deep
base.
– Dishes and items of cutlery must
not lie inside one another, or cover
each other.
– To avoid damage to glasses, they
must not touch.
– Lay small objects in the cutlery basket.
• Plastic items and pans with non stick
coatings have a tendency to retain
water drops; these items will not dry
as well as porcelain and steel items.
• Light items (plastic bowls etc.) must
be loaded in the upper basket and arranged so they do not move.
For washing in the dishwasher the following cutlery and dishes
are not suitable:
are of limited suitability:
• Cutlery with wooden, horn, china or • Only wash stoneware in the
mother-of-pearls handles.
dishwasher if it is specially marked as
being dishwasher-safe by the
• Plastic items that are not heat resistmanufacturer.
ant.
• Older cutlery with glued parts that are • Glazed patterns may fade if machine
washed frequently.
not temperature resistant.
•
Silver and aluminium parts have a
• Bonded cutlery items or dishes.
tendency
to discolour during wash• Pewter or copper items.
ing: Residues, e.g. egg white, egg
• Lead crystal glass.
yolk and mustard often cause disco• Steel items prone to rusting.
louring and staining on silver. There• Wooden platters.
fore always clean left-overs from silver
immediately, if it is not to be washed
• Items made from synthetics fibres.
straight after use.
Load cutlery and dishes
The lower basket
The lower basket is designed to take
saucepan, lids, plates, salad bowls, cutlery etc.
Service dishes and large lids should be
arranged around the edge of the basket,
ensuring that the spray arms can turn
freely.
16 electrolux load cutlery and dishes
Long and/or sharp items of cutlery
such as carving knives must be
positioned horizontally in the upper
basket. Take care when loading or
unloading sharp items such as knives.
Forks and spoons should be placed in
the removable cutlery basket with the
handles facing downwards and the knives with their handles facing upwards.
The rows of prongs in the lower basket
can lie flat to allow you to load pots, pans
and bowls.
If the handles protrude from the bottom
of the basket, obstructing the lower
spray arm, load the cutlery with the handles facing upwards.
Mix spoons with other cutlery to prevent
them from sticking together.
To make loading of the cutlery basket
easier, lower the cutlery basket handle.
The cutlery basket
Long bladed knives stored in an upright position are a potential hazard.
load cutlery and dishes electrolux 17
For best results we recommend that you
use the cutlery grids.
If the size and dimensions of the cutlery
do not allow the use of the grids, they
can be easily hidden.
The cutlery basket is in two parts which
can be separated to give greater loading
flexibility. To separate the two parts,
slide them horizontally in opposite directions and pull them apart.
To reassemble, reverse the procedure.
The upper basket
The upper basket is designed for saucers, salad bowls, cups, glasses, pots
and lids.
Arrange items on and underneath the
cup racks so that water can reach all
surfaces.
18 electrolux load cutlery and dishes
Glasses with long stems can be placed
upside down in the cup racks.
For taller items the cup racks can be folded upwards.
Before closing the door, ensured
that the spray arms can rotate
freely.
Adjusting the height of the upper
basket
If washing very large plates you can load
them in the lower basket after moving
the upper basket to the higher position.
For glasses with long stems (according
to the size and dimensions), set the glass
holder to the left or right position.
Maximum height of the dishes in
the lower basket
With upper basket
raised
31 cm
With upper basket
lowered
27 cm
To move to the higher position proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards until
the mechanism is engaged and the
basket is stable.
The central rows of prongs can be easily
lowered to improve loading flexibility.
To lower the basket to the original
position proceed as follows:
1. Pull out the basket until it stops.
use of detergent electrolux 19
2. Carefully lift both sides upwards and
then allow the mechanism to drop
back down slowly, keeping hold of it.
After loading your machine always
close the door, as an open door can
be a hazard.
Never lift or lower the basket on one
side only
When the basket is in the higher position you will not be able to use the
cup racks.
Use of detergent
Only use detergents specifically designed for use in dishwashers.
Please observe the manufacturer’s
dosing and storage recommendations as stated on the detergent
packaging.
Using no more than the correct
amount of detergent contributes to
reducing pollution.
Fill with detergent
1. Open the lid.
2. Fill the detergent dispenser (1) with
detergent. The marking indicates the
dosing levels:
20 = approximately 20 g of detergent
30 = approximately 30 g of detergent.
20 electrolux multi-tab function
4. Close the lid and press until it locks
in place.
1
2
3. All programmes with prewash need
an additional detergent dose (5/10 g)
that must be placed in the prewash
detergent chamber (2).
This detergent will be used during
the prewash phase.
When using detergent tablets; place
the tablet in compartment (1)
Detergent tablets from different
manufacturers dissolve at different
rates. For this reason, some detergent tablets do not attain their full
cleaning power during short washing programmes. Therefore, please
use long washing programmes
when using detergent tablets, to ensure the complete removal of detergent residuals.
Multi-tab function
This appliance is equipped with the
"Multitab function", that allows the use
of the "Multitab" combi detergent tablets.
multi-tab function electrolux 21
These products are detergents with a
combined cleaning, rinsing and salt
functions. They can also contain other
different agents depending on which
kind of tablets you choose ("3 in 1", "4 in
1", "5 in 1" etc...).
Check whether these detergents are
suitable for your water hardness. See
the manufacturers instructions.
Once this function is selected it will remain active for all following wash programmes.
With the selection of this function the inflow of rinse aid and salt from each respective supply container is
automatically deactivated and also the
indicator lights for salt and rinse aid are
deactivated.
When using the "Multitab function", the
cycle durations may change. If this is the
case, the running time for the programme is automatically updated on the
digital display.
Activation/deactivation of the
Multitab function
Activate/deactivate the ''Multitab
function'' before the start of a washing programme.
Once the programme is running, the
"Multitab function " can NO longer
be changed. If you want to cancel
the "Multitab function " you have to
cancel the programme setting and
then deactivate the ''Multitab function''. In this case you have to set a
washing programme (and desired
options) again.
Activation/deactivation of the
rinse aid dispenser
Simultaneously press and hold the two
Multitab buttons (function buttons D and
E) until the Multitab indicator light illuminates. This means that the function is
active.
To deactivate the function press the
same buttons again until the indicator
light corresponding to the Multitab function symbol turns off.
If the drying results are not
satisfactory we suggest that you:
1. Fill up the rinse aid dispenser
with rinse aid.
2. Activate the rinse aid dispenser.
3. Set the rinse aid dosage to position 2.
• The activation/deactivation of the
rinse aid is only possible with the
Multitab function active.
1. Press the On/Off button. The
dishwasher must be in setting mode.
2. Simultaneously press and hold function buttons B and C, until the lights
of function buttons A , B, and C start
flashing.
3. Press function button B, the lights of
function buttons A and C turn off
while the light of function button B
continues to flash. The digital display
indicates the current setting.
22 electrolux select and start a washing programme
Rinse aid dispenser deactivated
Rinse aid dispenser activated
4. To change the setting, press button
B again, the digital display indicates
the new setting.
5. To memorise the operation, switch
off the dishwasher by pressing the
On/Off button.
1. Deactivate the Multitab function.
2. Fill up the salt container and the
rinse aid dispenser again.
3. Adjust the water hardness setting to the highest setting and
perform 1 normal washing programme without loading any
dishes.
4. Adjust the water hardness setting according to the hardness of
the water in your area.
5. Adjust the rinse aid dosage.
If you decide to revert back to the
use of individual detergents we advise that you:
Select and start a washing programme
Select the washing programme and
delay start with the door slightly
opened. The start of the programme
or the countdown of the delay start
will occur only after the closure of
the door. Until then it is possible to
modify the settings
1. Check that the baskets have been
loaded correctly and that the spray
arms are free to rotate.
2. Check that the water tap is opened.
3. Press the On/Off button. The
dishwasher must be in setting mode.
4. Press the button corresponding to
the required programme (see
''Washing programmes'' chart).
When a programme has been selected the corresponding light illuminates.
The programme in progress indicator light illuminates.
Close the dishwasher door, the programme starts automatically.
The programme in progress indicator light remains illuminated.
Setting and starting the
programme with delay start
1. After having selected the washing
programme, press the delay start
button until the flashing number of
select and start a washing programme electrolux 23
2.
3.
4.
5.
hours for the delay start appear in the
digital display. The start of the selected washing programme can be delayed for between 1 and 19 hours.
Close the dishwasher door, the
countdown starts automatically. The
number in the display is no longer
flashing but fixed with static light.
The countdown will decrease with
steps of 1 hour.
The opening of the door will interrupt
the countdown. Close the door; the
countdown will continue from the
point at which it was interrupted.
Once the delay start has elapsed the
programme will start automatically.
With the delay start function set, the
programme in progress indicator
light is off. Once the countdown of
the delay start has elapsed, the
washing programme will start
automatically and the programme in
progress indicator light will illuminate.
The selection of the washing programme and delay start can also occur with the door closed. Keep in
mind that this way, once a washing
programme button is pressed you
have ONLY 3 seconds in which you
can choose another programme or
select a delay start, after which the
selected programme will start
automatically.
Interrupt or cancel a washing programme in progress ONLY if it's
absolutely necessary.
Attention! Hot steam may escape
when the door is opened. Open the
door carefully.
Cancel a delay start or a washing
programme in progress
• Simultaneously press and hold the
two Cancel buttons (function buttons
B and C) until all the programme lights
illuminate.
• Cancelling a delay start will also cancel the washing programme. You
have to select the washing programme again.
• If a new washing programme is to be
selected, check that there is detergent
in the detergent dispenser.
End of the washing programme
• The dishwasher will automatically
stop and the programme in progress indicator light turns off.
• The End indicator light will illuminate.
• The light of the programme just ended
will remain on.
• Zero appears in the digital display.
1. Switch off the dishwasher by pressing the On/Off button.
2. Open the dishwasher door, leave it
ajar and wait a few minutes before
24 electrolux unloading the dishwasher
removing the dishes; this way they
will be cooler and the drying will be
improved.
Unloading the dishwasher
• Hot dishes are sensitive to knocks.
The dishes should therefore be allowed to cool down before removing
from the appliance.
• Empty the lower basket first and then
the upper one; this will avoid water
dripping from the upper basket onto
the dishes in the lower one.
• Water may appear on the sides and
the door of the dishwasher as the
stainless steel will eventually become
cooler than the dishes.
When the washing programme has
finished, it is recommended that the
dishwasher is unplugged and the
water tap turned off.
Washing programmes
Programme
Intensive
1)
Quick
2)
Degree of
soil
Type of load
Heavy soil
Crockery,
cutlery, pots
and pans
Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Drying
Any
Crockery,
cutlery, pots
and pans
Prewash
Main wash up to 45°C or 70°C
1 or 2 intermediate rinses
Final rinse
Drying
Normal or
light soil
Programme description
Crockery and Main wash up to 60°C
cutlery
Final rinse
washing programmes electrolux 25
Programme
3)
Prewash
Degree of
soil
Type of load
Normal soil
Prewash
Main wash up to 50°C
Crockery and
1 intermediate rinse
cutlery
Final rinse
Drying
Partial load (to
be completed
later in the
day).
Any
Programme description
1 cold rinse (to avoid food scraps
from sticking).
This programme does not require
the use of detergent.
1) During the "Auto" washing programme the level of soiling on the dishes is determined by how cloudy
the water is. The programme duration, water and energy consumption levels can vary; this depends
upon whether the appliance is fully or partially loaded and if the dishes are lightly or heavily soiled. The
temperature of the water is automatically adjusted between 45°C and 70°C.
2) Ideal for washing a partially loaded dishwasher. This is the perfect daily programme, made to meet
the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery.
3) Test programme for test institutes
Consumption values
Programme
Programme duration
(in minutes)
Energy consumption
(in kWh)
Water consumption
(in litres)
Intensive
110 - 120
1,8 - 2,0
23 - 25
Auto
90 - 130
1,1 - 1,7
12 - 23
Quick
30
0,9
9
Eco 1)
150 - 160
1,0 - 1,2
14 - 16
12
0,1
4
Prewash
1) Test programme for test institutes
The consumption values are intended as a guide and depends on the
pressure and the temperature of the
water and also by the variations of
the power supply and the amount of
dishes.
26 electrolux care and cleaning
Care and cleaning
Cleaning the filters
The filters must be checked and cleaned
from time to time. Dirty filters will degrade the washing result.
Before cleaning the filters ensure
that the machine is switched off.
1. Open the door, remove the lower
basket.
2. The dishwasher filter system comprises a coarse filter (A), a microfilter
(B) and a flat filter. Unlock the filter
system using the handle on the microfilter.
4. Take hold of the coarse filter (A) by
the handle with the hole and remove
from the microfilter (B).
5. Clean all filters thoroughly under running water.
6. Remove the flat filter from the base
of the washing compartment and
clean both faces thoroughly.
3. Turn the handle about 1/4 a turn anticlockwise and remove the filter system
7. Put the flat filter back in the base of
the washing compartment and ensure that it fits perfectly.
8. Place the coarse filter (A) in the microfilter (B) and press together.
9. Put the filter combination in place
and lock by turning the handle clockwise to the stop. During this process
care and cleaning electrolux 27
ensure that the flat filter does not
protrude above the base of the
washing compartment.
NEVER use the dishwasher without
filters. Incorrect repositioning and
fitting of the filters will produce poor
washing results and will result in
damage to the appliance
Prolonged periods of nonoperation
If you are not using the machine for any
prolonged period of time you are advised to:
1. Unplug the appliance and then turn
off the water.
2. Leave the door ajar to prevent the
formation of any unpleasant smells.
3. Leave the inside of the machine
clean.
Frost precautions
NEVER try to remove the spray
arms.
If residues of soil have clogged the
holes in the spray arms, remove the
debris with a cocktail stick.
Avoid placing the machine in a location
where the temperature is below 0°C. If
this is unavoidable, empty the machine,
close the appliance door, disconnect the
water inlet pipe and empty it.
External cleaning
Moving the machine
Clean the external surfaces of the machine and control panel with a damp soft
cloth. If necessary use only neutral detergents. Never use abrasive products,
scouring pads or solvent (acetone, trichloroethylene etc...).
If you have to move the machine (moving
house etc...):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with
the hoses.
Avoid over tilting the machine during
transportation.
Internal cleaning
Ensure that the seals around the door,
the detergent and rinse aid dispensers
are cleaned regularly with a damp cloth.
We recommend every 3 months to run
the wash programme for heavy soiled
dishes using detergent but without
dishes.
28 electrolux what to do if...
What to do if...
The dishwasher will not start or stops
during operation.
Certain problems can be due to the lack
of simple maintenance or oversights,
which can be solved with the help of the
Fault codes and malfunction
hints described in the chart, without calling out an engineer.
Switch off the dishwasher, open the
door and carry out the following suggested corrective actions.
Possible cause and solution
• continuous flashing of the light of the • The water tap is blocked or furred
running programme
with limescale.
Clean the water tap.
•
appears in the digital display
• The water tap is turned off.
The dishwasher does not fill with
Turn the water tap on.
water
• The filter (where present) in the threaded hose fitting at the water inlet valve
is blocked.
Clean the filter in the threaded hose.
• The water inlet hose has not been
correctly laid or it is kinked or
squashed.
Check the water inlet hose connection.
• continuous flashing of the light of the • The sink spigot is blocked.
running programme
Clean out the sink spigot.
•
• The water drain hose has not been
appears in the digital display
correctly laid or it is kinked or
The dishwasher will not drain
squashed.
Check the water drain hose connection.
• continuous flashing of the light of the • Close the water tap and contact your
running programme
local Service Force Centre.
•
appears in the digital display
Anti-flood device is activated
what to do if... electrolux 29
Malfunction
The programme does not start
Once these checks have been carried
out switch on the appliance.
The programme will continue from the
point at which it was interrupted.
If the malfunction or fault code reappears contact your local Service Force
Centre.
For other fault codes not described in
the above chart, please contact your local Service Force Centre.
Contact your local Service Force Centre,
quoting the model (Mod.), product number (PNC) and serial number (S.N.).
Possible cause and solution
• The dishwasher door has not been
properly closed.
Close the door.
• The main plug is not plugged in.
Insert the main plug
• The fuse has blown out in the household fuse box.
Replace the fuse.
• Delay start has been set.
If dishes are to be washed
immediately, cancel the delay start.
This information can be found on the rating plate located on the side of the
dishwasher door.
So that you always have these numbers
at hand, we recommend you to make a
note of them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30 electrolux what to do if...
The wash results are not satisfactory
The dishes are
not clean
• The wrong programme has been selected.
• The dishes are arranged in such a way as to stop water
reaching all parts of a surface. The baskets must not be
overloaded.
• The spray arms do not rotate freely due to incorrect arrangement of the load.
• The filters in the base of the washing compartment are dirty
or incorrectly positioned.
• Too little or no detergent has been used.
• Where there are limescales deposits on the dishes; the salt
container is empty or incorrect level of the water softener
has been set.
• The drain hose connection is not correct.
• The salt container cap is not properly closed.
The dishes are
wet and dull
• Rinse aid was not used.
• The rinse aid dispenser is empty.
There are
streaks, milky
spots or a bluish coating on
glasses and
dishes
• Decrease rinse aid dosage.
• Increase rinse aid dosage.
Water drops
have dried onto • The detergent may be the cause. Contact the detergent
glasses and
manufacturer consumer care line.
dishes
If after all these checks, the problem persists, contact your local Service Force
Centre.
technical data electrolux 31
Technical data
Dimensions
Width
Height
Depth
59,6 cm
81,8 - 89,8 cm
57,5 cm
Electrical connection Voltage - Overall power Fuse
Information on the electrical connection is given on the
rating plate on the inner edge of the dishwasher door.
Water supply pressure
Minimum
Maximum
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Capacity
12 place settings
Weight
39,5 kg
Hints for test institutes
Testing in accordance with EN 60704
must be carried out with appliance fully
loaded and using the test programme
(see "Consumption values").
Test in accordance with EN 50242 must
be carried out when the salt container
and rinse aid dispenser have been filled
with salt and rinse aid respectively and
using the test programme (see
"Consumption values").
Full load: 12 standard place settings
Amount of detergent required:
5 g + 25 g (Type B)
Rinse aid setting
position 4 (Type III)
32 electrolux installation
Cup racks: position A
Arrangement upper basket (take off the
glass holder)
Arrangement lower basket
Arrangement cutlery basket
Installation
Any electrical and/or plumbing work
required to install this appliance
should be carried out by a qualified
electrician and/or plumber or competent person.
water connection electrolux 33
Remove all packaging before positioning the machine.
If possible, position the machine next to
a water tap and a drain.
This dishwasher is designed to be fitted
under a kitchen counter or work surface.
Attention! Carefully follow the instructions on the enclosed template for building in the dishwasher and fitting the
furniture panel.
No further openings for the venting of the
dishwasher are required, but only to let
the water fill and drain hose and power
supply cable pass through.
The dishwasher incorporates adjustable
feet to allow the adjustment of the
height.
During all operations that involve
accessibility to internal components the
dishwasher has to be unplugged.
When inserting the machine, ensure that
the water inlet hose, the drain hose and
the supply cable are not kinked or
squashed.
Fixing to the adjacent units
The dishwasher must be secured
against tilting.
Therefore make sure that the counter it
is fixed under, is suitably secured to a
fixed structure (adjacent kitchen units
cabinets, wall).
Levelling
Good levelling is essential for correct
closure and sealing of the door.
When the appliance is correctly levelled,
the door will not catch on either side of
the cabinet .
If the door does not close correctly,
loosen or tighten the adjustable feet until
the machine is perfectly level.
Water connection
Water supply connection
This dishwasher may be fed with either
hot (max. 60°) or cold water. Nevertheless we advise you a cold water supply.
A hot water supply is not always efficient
with very soiled crockery as it shortens
the washing programmes a lot.
For making the connection itself, the
coupling nut fitted to the machine’s supply hose is designed to screw onto a
3/4" gas thread spout or to a purpose
made quick-coupling tap such as the
Press-block.
The water pressure must be within the
limits given in the "Technical data". Your
local Water Authority will advise you on
the average mains pressure in your area.
The water inlet hose must not be kinked,
crushed, or entangled when it is being
connected.
The dishwasher features fill and drain
hoses which can be turned either to the
left or the right to suit the installation by
means of the locknut. The locknut
must be correctly fitted to avoid water leaks.
34 electrolux water connection
Attention! NOT all models of dishwashers have fill and drain hoses
provided with a locknut. In this case,
this facility is not available.
If the machine is connected to new pipes
or pipes which have not been used for a
long time, you should run the water for a
few minutes before connecting the inlet
hose.
DO NOT use connection hoses
which have previously been used for
an old appliance.
This appliance has been fitted with
safety features which will prevent
the water used in the appliance from
returning back into the drinking water system. This appliance complies
with the applicable plumbing regulations.
Water inlet hose with safety valve
After connecting the double-walled water inlet hose, the safety valve is next to
the tap. Therefore the water inlet hose is
only under pressure while the water is
running. If the water inlet hose starts to
leak during this operation, the safety
valve cuts off the running water.
Please take care when installing the water inlet hose:
• The electrical cable for the safety valve
is in the double-walled water inlet
hose. Do not immerse the water inlet
hose or the safety valve in water.
• If water inlet hose or the safety valve
is damaged, remove the mains plug
immediately.
• A water inlet hose with safety valve
must only be replaced by the Service
Force Centre.
Warning! Dangerous voltage
Water outlet hose connection
The end of the drain hose can be connected in the following ways:
1. To the sink outlet spigot, securing it
to the underside of the work surface.
This will prevent waste water from
the sink running into the machine.
2. To a stand pipe provided with venthole, minimum internal diameter 4
cm.
The waste connection must be at a
maximum height of 60 cm from the bottom of the dishwasher.
water connection electrolux 35
When connecting the drain hose to an
under sink trap spigot, the entire plastic membrane (A) must be removed. Failure to remove all the membrane will result in food particles building
up over time eventually blocking the
dishwasher drain hose spigot
The drain hose can face either to the
right or left of the dishwasher
Ensure the hose is not bent or squashed
as this could prevent or slow down the
discharge of water.
The sink plug must not be in place when
the machine is draining as this could
cause the water to syphon back into the
machine.
The total length of the drain hose, including any extension you might add,
must be no longer than 4 metres. The
internal diameter of the extension hose
must be no smaller than the diameter of
the hose provided.
Likewise the internal diameter of the
couplings used for connections to the
waste outlet must be no smaller than the
diameter of the hose provided.
Our appliances are supplied with a
security device to protect against
the return of dirty water back into
the machine. If the spigot of your
sink has a "no return valve" incorporated this can prevent the correct
draining of your dishwasher. We
therefore advise you to remove it.
To avoid water leakage after installation make sure that the water couplings are tight.
36 electrolux electrical connection
Electrical connection
Safety standards require the appliance to be earthed.
Prior to using the appliance for the
first time, ensure that the rated voltage and type of supply on the rating
plate match that of the supply where
the appliance is to be installed. The
fuse rating is also to be found on the
rating plate
Always plug the mains plug into a
correctly installed shockproof
socket.
Multi-way plugs, connectors and extension cables must not be used.
This could constitute a fire hazard
through overheating.
If necessary, have the domestic wiring system socket replaced. In case
that the electrical cable has to be
replaced, contact your local Service
Force centre.
The plug must be accessible after
the appliance has been installed.
Never unplug the appliance by pulling on the cable. Always pull the
plug.
The manufacturer accepts no
liability for failure to observe the
above safety precautions.
Environment concerns
The symbol
on the product or on its
packaging indicates that this product
may not be treated as household waste.
Instead it should be taken to the
appropriate collection point for the
recycling of electrical and electronic
equipment. By ensuring this product is
disposed of correctly, you will help
prevent potential negative
consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling
of this product. For more detailed
information about recycling of this
product, please contact your local
council, your household waste disposal
service or the shop where you
purchased the product.
Packaging material
The packaging materials are
environmentally friendly and can be recycled. The plastic components are
identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging materials in the appropriate
container at the community waste
disposal facilities.
environment concerns electrolux 37
When a unit is no longer being used:
• Pull the plug out of the socket.
• Cut off the cable and plug and dispose of them.
• Dispose of the door catch. This
prevents children from trapping
themselves inside and endangering their lives.
38 electrolux
www.electrolux.com
www.electrolux.co.uk
117978490 - 102007
Download PDF

advertising