Etna AFI8527ZT/E01 User Manual

AFI8527ZT
Bedienungsanleitung
Geschirrspüler
instruction book
dishwasher
Seite 2
page 20
Contents
Safety instructions
21
Disposal
21
Economical and ecological dishwashing
21
Installation instructions
Building-in
Levelling
Fixing to the adjacent units
Water supply connections
Water inlet hose with safety valve
Water outlet hose connection
Electrical connection
22
22
22
22
22
22
23
23
Description of the appliance
24
The control panel
25
Prior to using for the first time
The water softener
Filling with dishwasher salt
Rinse aid
27
27
28
28
In daily use
Loading cutlery and dishes
The lower basket
The cutlery basket
The upper basket
Adjusting the height of the upper basket
Use of detergent
29
29
29
29
30
30
31
Different kinds of detergent
31
Washing programmes
32
Starting a washing programme
33
Maintenance and cleaning
Cleaning the filters
Prolonged periods of non-operation
Frost precautions
Moving the machine
34
34
34
34
34
Something not working
Service and spare parts
35
36
Hints for test centres
37
Technical specifications
Dimensions
Width
Height
Max depth
Max depth with open door
Electrical connection:
Voltage
Overall power
Fuse
Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher’s door.
Water supply pressure
Minimum
Maximum
Capacity
59.6 cm
81.8 - 87.8 cm
55.5 cm
114 cm
0,05 MPa
0,8 MPa
12 place settings
This appliance complies with the following E.E.C. Directives:
- 73/23 or 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 or 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
20
Safety instructions
It is most important that this instruction book should be retained with the appliance for future reference. Should the
appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that
the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the
relevant safety information.
This information has been provided in the interest of your safety. You MUST read it carefully before installing or using the
appliance.
Installation
●
Check your dishwasher for any transport damage. Never
connect a damaged machine. If your dishwasher is
damaged, you should contact your supplier.
●
For safety reasons it is dangerous to alter the specifications
or attempt to modify this product in any way.
●
Any electrical and plumbing work required to install this
appliance should be carried out by a qualified and
competent person.
●
Care must be taken to ensure that the appliance does not
stand on the electrical supply cable.
●
The sides of the dishwasher must never be drilled to
prevent damage to hydraulic components.
●
Disposal
Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.
Plastic parts are marked with standard international
abbreviations:
>PE<
for polyethylene, e.g. sheet wrapping material.
>PS<
for polystyrene, e.g. padding material (always CFCfree).
>POM< for polyoxymethylene, e.g. plastic clips.
Child safety
●
This appliance is designed to be operated by adults.
●
Children should not be allowed to tamper with the controls
or play with the product.
●
Ensure the packaging materials for this appliance are kept
away from children so as to prevent the risk of injury or
suffocation.
●
The water in your dishwasher is not for drinking. Detergent
residues may still be present in your machine. Keep
children well away from your dishwasher when the door is
open.
●
Keep all detergents in a safe place out of children's reach.
Under no circumstances should you attempt to repair the
machine yourself. Repairs carried out by inexperienced
persons may cause injury or serious malfunctioning.
Contact your local Service Force Centre. Always insist on
genuine spare parts.
Cardboard packaging is manufactured from recycled paper
and should be deposited in the waste paper collection for
recycling.
As and when you cease to use your dishwasher and withdraw
it from service, your should render it unserviceable before
having it disposed of.
Warning! Children at play could lock themselves in your
dishwasher or otherwise endanger their lives. Therefore cut off
the power supply cable and make the door closing device
unusable to prevent children from being trapped inside.
For the disposing of the appliance please take it to a recycling
centre or to your dealer who may, for a small contribution to
the costs, dispose it for you.
Your dishwasher in day-to-day use
The symbol
on the product or on its packaging indicates
that this product may not be treated as
household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative
consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of
this product.
For more detailed information about recycling of this product,
please contact your local city office, your household waste
disposal service or the shop where you purchased the
product.
●
Items that are contaminated by petrol, paint, steel or iron
debris, corrosive, acidic or alkaline chemicals must not be
washed in this dishwasher.
●
Under no circumstances should you open the door whilst
the appliance is in operation, especially during the washing
phase, hot water may escape. However, if the door is
opened, a safety device ensures that the machine stops.
●
Only use products (detergent, salt and rinse aid) specifically
designed for use in dishwashers.
●
Long bladed knives stored in an upright position are a
potential hazard.
●
Long and/or sharp items of cutlery such as carving knives
must be positioned horizontally in the upper basket.
●
Ensure that the door of the dishwasher is always closed
when it is not being loaded or unloaded. In this way you will
avoid anybody tripping over the open door and hurting
themselves.
●
When finishing loading or unloading close the door, as an
open door can be a hazard.
●
Ensure that the water softener is correctly adjusted.
●
Do not pre-wash under running water.
●
Do not sit or stand on the open door.
●
●
Isolate the appliance from the power supply and turn off the
water supply after use.
Select the wash programme to suit the nature and degree of
the soiling on the dishes.
●
Do not use more detergent, dishwasher salt and rinse aid
than is recommended in these operating instructions and by
the manufacturer of the respective product.
●
Economical and
ecological dishwashing
This product should be serviced by an authorised service
engineer, and only genuine spare parts should be used.
21
Installation instructions
Any electrical and/or plumbing work required to install
this appliance should be carried out by a qualified
electrician and/or plumber or competent person.
If the machine is connected to new pipes or pipes which have
not been used for a long time, you should run the water for a
few minutes before connecting the inlet hose.
Remove all packaging before positioning the machine.
DO NOT use connection hoses which have previously
been used for an old appliance.
If possible, position the machine next to a water tap and a
drain.
This appliance has been fitted with safety features which will
prevent the water used in the appliance from returning back
into the drinking water system. This appliance complies with
the applicable plumbing regulations.
Building-in
This dishwasher is designed to be fitted under a kitchen
counter or worksurface.
Water inlet hose with safety valve
Attention!
Carefully follow the instructions on the enclosed template for
building in the dishwasher and fitting the furniture panel.
No further openings for the venting of the dishwasher are
required, but only to let the water fill and drain hose and power
supply cable pass through.
After connecting the double-walled water inlet hose, the safety
valve is next to the tap. Therefore the water inlet hose is only
under pressure while the water is running. If the water inlet
hose starts to leak during this operation, the safety valve cuts
off the running water.
The dishwasher incorporates adjustable feet to allow the
adjustment of the height.
Please take care when installing the water inlet hose:
During all operations that involve accessibility to internal
components the dishwasher has to be unplugged.
- The electrical cable for the safety valve is in the doublewalled water inlet hose. Do not immerse the water inlet hose
or the safety valve in water.
When inserting the machine, ensure that the water inlet hose,
the drain hose and the supply cable are not kinked or
squashed.
- If water inlet hose or the safety valve is damaged, remove
the mains plug immediately.
- A water inlet hose with safety valve must only be replaced by
a specialist or by the Service Force Centre.
Levelling
- Place the water inlet hose in such a way that it is never
higher than the bottom edge of the safety valve.
Good levelling is essential for correct closure and sealing of
the door.
When the appliance is correctly levelled, the door will not catch
on either side of the cabinet.
WARNING!
Dangerous voltage
If the door does not close correctly, loosen or tighten the
adjustable feet until the machine is perfectly level.
Fixing to the adjacent units
The dishwasher must be secured against tilting.
Therefore make sure that the counter it is fixed under, is
suitably secured to a fixed structure (adjacent kitchen units
cabinets, wall).
Water supply connections
This dishwasher may be fed with either hot (max. 60°) or cold
water. Nevertheless we advise you a cold water supply.
A hot water supply is not always efficient with very soiled
crockery as it shortens the washing programmes a lot.
For making the connection itself, the coupling nut fitted to the
machine’s supply hose is designed to screw onto a 3/4" gas
thread spout or to a purpose made quick-coupling tap such as
the Press-block.
The water pressure must be within the limits given in the
"Technical specifications". Your local Water Authority will
advise you on the average mains pressure in your area.
The water inlet hose must not be kinked, crushed, or entangled
when it is being connected.
The dishwasher features fill and drain hoses which can be
turned either to the left or the right to suit the installation by
means of the locknut. The locknut must be correctly fitted
to avoid water leaks. (Attention! NOT all models of
dishwashers have fill and drain hoses provided with locknut. In
this case, this kind of facility is not possible).
22
Water outlet hose connection
Electrical connection
The end of the drain hose can be connected in the following
ways:
Information concerning the electrical connection is given on the
rating plate on the edge of the dishwasher’s door.
1. To the sink outlet spigot, securing it to the underside of the
work surface. This will prevent waste water from the sink
running into the machine.
Before plugging the appliance into the wall socket, make sure
that:
1. The mains voltage and current rating at the site of
installation match the nominal voltage and current rating
given on the rating plate.
2. To a stand pipe provided with vent-hole, minimum internal
diameter 4 cm.
2. The meter, fuses, mains power supply and wall socket can
all take the maximum load required. Make sure that the
socket and plug are compatible without having to use any
type of adaptor. If necessary, have the domestic wiring
system socket replaced.
The waste connection must be at a height of between 30 cm
(minimum) and 100 cm (maximum) from the bottom of the
dishwasher.
The drain hose can face either to the right or left of the
dishwasher
Ensure the hose is not bent or squashed as this could prevent
or slow down the discharge of water.
To isolate the dishwasher from mains, remove the mains plug.
Important!
The plug must still be accessible after the appliance
has been installed.
The sink plug must not be in place when the machine is
draining as this could cause the water to syphon back into the
machine.
In case that the electrical cable has to be replaced,
please contact your local Service Force Centre.
If you use a drain hose extension it must be no longer than 2
metres and its internal diameter must be no smaller than the
diameter of the hose provided.
The appliance should not be connected to the
electrical supply by means of an extension cable.
Safety standards require the appliance to be
earthed.
The manufacturer accepts no liability for failure to
observe the above safety precautions.
Likewise the internal diameter of the couplings used for
connections to the waste outlet must be no smaller than the
diameter of the hose provided.
Attention!
Our appliances are supplied with a security device to protect
against the return of dirty water back into the machine.
If the spigot of your sink has a "no return valve" incorporated
this can prevent the correct draining of your dishwasher.
We therefore advise you to remove it.
23
Description of the appliance
1.
Upper basket stop
2.
Water hardness dial
3.
Salt container
4.
Detergent dispenser
5.
Control panel
6.
Rating plate
7.
Rinse aid dispenser
8.
Filters
9.
Lower spray arm
10. Upper spray arm
11. Upper basket
24
The control panel
3 in 1 button
Function buttons
On/Off button
Digital display
1
2
3
Indicator lights
Programme selection button
Half Load button
Delay start button
Function buttons: in addition to the selection of the
"Half load" button: this option is useful and economical
washing programme, "half load" option and "delay start"
option, the following functions can also be set with the help of
these buttons:
when only a few dishes need washing reducing the
consumption of water and energy. This option must be linked
to the selection of a washing programme.
- the setting of the water softener,
Remember to load both baskets.
- activation/deactivation of the rinse aid dispenser,
With the use of this function, the cycle durations change. In
this case, in the digital display, the indication of the running
time of the programme is automatically updated.
- the cancelling of a washing programme in progress,
- deactivation/activation of the audible signals.
With only some programmes this option is available (See
"Washing programmes" chart).
"Programme selection" button: allows the selection
of the desired washing programme (see "Washing
programmes" chart).
"Half load" option
available
- button activated
- indicator light on
"Half load" option
not available
- button deactivated
- indicator light off
"Delay start" button: this option allows the start of the
programme to be delayed from 1 to 19 hours.
The digital display indicates:
Indicator lights: have the following meanings:
- the level of hardness to which the water softener is set,
- if the audible signals are activated/deactivated,
salt refilling indicator light: illuminates when the salt
has run out
- the number corresponding to the selected washing
programme,
rinse aid refilling indicator light: illuminates when
the rinse aid has run out
- if the rinse aid dispenser is activated/deactivated,
- the approximate remaining time of the washing programme,
end of programme indicator light: illuminates when
the washing programme has ended
- the end of the programme (a zero will appear in the digital
display),
- the countdown of the delay start,
- fault codes concerning malfunction of the dishwasher.
25
3 in 1 button: This appliance is equipped with the 3 in 1
function, that allows the use of the "3 in 1" combi detergent
tablets.
This function can be selected with all washing programmes.
With the selection of this function the inflow of rinse aid and
salt from each respective supply container is automatically
deactivated and also the indicator lights for salt and rinse aid
are deactivated.
Select the 3 in 1 function before the set of a washing
programme.
Once selected this function (button indicator light illuminated) it
will remain active also for the following washing programmes,
to deactivate the function, press the button (button indicator
light off).
With the use of the 3 in 1 function, the cycle durations may
change. In this case, in the digital display, the indication of the
running time of the programme is automatically updated.
Audible signals
Audible signals have been introduced to help indicate which
operations the dishwasher is performing:
- setting of the water softener
- end of programme
- intervention of an alarm due to malfunction
Deactivation/activation of the audible signals
(The dishwasher must be switched off)
Factory setting: audible signals activated
1. Press the On/Off button. The indicator light of the
programme selection button will illuminate and 2 horizontal
lines (--) are visible in the digital display (setting mode).
If the number of a programme (1 - 2 - 3 etc..) is visible in the
display, this means that a washing programme is set.
The programme must be cancelled: press simultaneously
function buttons 2 and 3 for about 2 seconds. 2 horizontal
lines will appear in the digital display, this means that the
set washing programme has been cancelled and the
machine is now in setting mode.
NOTE: Once the programme is running, the 3 in 1 function
can NO longer be changed. If you want to exclude the 3 in 1
function you have to cancel the programme setting (see
chapter "Starting a washing programme" - "Cancel a washing
programme in progress") and then deactivate the 3 in 1
function.
In this case you have to set a washing programme (and
desired options) again.
2. Press simultaneously function buttons 2 and 3, the indicator
lights of the function buttons 1, 2 and 3 start flashing.
NOTE: if the drying results are not satisfactory we suggest
that you reactivate the rinse aid dispenser.
The activation/deactivation of the rinse aid dispenser can only
be possible with the 3 in 1 function active.
3. Press function button 3, the indicator lights of function
buttons 1 and 2 turn off while the indicator light of the button
3 goes on flashing, the digital display indicates the current
setting.
Activation/deactivation of the rinse aid
dispenser
Audible signals deactivated
(The dishwasher must be switched off)
Audible signals activated (factory set)
When the rinse aid dispenser has been activated, the rinse
aid indicator light on the control panel is automatically
activated.
4. To change the current setting, press again function button 3,
the digital display will indicate the new setting.
1. Press the On/Off button. The indicator light of the
programme selection button will illuminate and 2 horizontal
lines (--) are visible in the digital display (setting mode).
If the number of a programme (1 - 2 - 3 etc..) is visible in the
display, this means that a washing programme is set.
The programme must be cancelled: press simultaneously
function buttons 2 and 3 for about 2 seconds. 2 horizontal
lines will appear in the digital display, this means that the
set washing programme has been cancelled and the
machine is now in setting mode.
5. To memorise the operation, switch off the dishwasher by
pressing the On/Off button or wait about 60 seconds after
which the dishwasher will automatically return to setting
mode.
2. Press simultaneously function buttons 2 and 3, the indicator
lights of the function buttons 1, 2 and 3 start flashing.
3. Press function button 2, the indicator lights of function
buttons 1 and 3 turn off while the indicator light of the button
2 goes on flashing, the digital display indicates the current
setting.
Rinse aid dispenser deactivated
Rinse aid dispenser activated
4. To change the setting, press again function button 2, the
digital display indicates the new setting.
5. To memorise the operation, switch off the dishwasher by
pressing the On/Off button or wait about 60 seconds after
which the dishwasher will automatically return to setting
mode.
26
Prior to using for the first time
Before using your dishwasher for the first time:
b) Setting electronically
(The dishwasher must be switched off)
1. Ensure that the electrical and water connections comply
with the installation instructions
NOTE: the electronic setting of the water softener is
possible ONLY with the 3 in 1 function deactivated.
2. Remove all packaging from inside the appliance
3. Set the water softener
The dishwasher is factory set at level 5.
4. Pour 1 litre of water inside the salt container and then fill
with dishwasher salt
1. Press the On/Off button. The indicator light of the
programme selection button will illuminate and 2 horizontal
lines (--) are visible in the digital display (setting mode).
If the number of a programme (1 - 2 - 3 etc..) is visible in the
display, this means that a washing programme is set.
The programme must be cancelled: press simultaneously
function buttons 2 and 3 for about 2 seconds. 2 horizontal
lines will appear in the digital display, this means that the
set washing programme has been cancelled and the
machine is now in setting mode.
5. Fill the rinse aid dispenser
Note:
If you want to use the "3 in 1" combi detergents, carefully
read the information given in "Different kinds of
detergents".
The water softener
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these minerals and salts, the harder
your water is.
Water hardness is measured in equivalent scales, German
degrees (°dH), French degrees (°TH) and mmol/l (millimol per
litre - international unit for the hardness of water).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
2. Press simultaneously function buttons 2 and 3, until the
indicator lights of the function buttons 1, 2 and 3 start
flashing.
3. Press function button 1, the indicator lights of function
buttons 2 and 3 turn off while the indicator light of the
button 1 goes on flashing, the digital display indicates the
current level and a sequence of intermittent audible signals
are heard.
The current level is indicated by the number visible in the
display and the number of intermittent audible signals
heard.
Example:
The water softener must be set in both ways: manually, using
the water hardness dial and electronically, using the function
buttons on the control panel.
displayed + 5 audible signals = level 5.
4. To change the level, press function button 1. Each time the
button is pressed the level changes. (For the selection of
the new level see the chart).
a) Setting manually
1. Open the dishwasher door.
Examples:
if the current level is 5, by pressing button 1 once, level 6 is
selected.
if the current level is 10, by pressing button 1 once, level 1
is selected.
2. Remove the lower basket from the dishwasher.
3. Turn the water hardness dial to position 1 or 2 (see table).
4. Replace the lower
basket.
The dishwasher is factory set
at position 2.
5. To memorise the operation, switch off the dishwasher by
pressing the On/Off button or wait about 60 seconds after
which the dishwasher will automatically return to setting
mode.
Water hardness
Adjusting the water
hardness setting
Level indicated
on the
digital display
Number of
audible
signals
Use
of salt
°dH
°TH
mmol/l
Range
manually
electronically
51 - 70
91 - 125
9,0 - 12,5
IV
2
level 10
10
yes
43 - 50
76 - 90
7,6 - 8,9
IV
2
level 9
9
yes
37 - 42
65 - 75
6,5 - 7,5
IV
2
level 8
8
yes
29 - 36
51 - 64
5,1 - 6,4
IV
2
level 7
7
yes
23 - 28
40 - 50
4,0 - 5,0
IV
2
level 6
6
yes
19 - 22
33 - 39
3,3 - 3,9
III
2
level 5
5
yes
15 - 18
26 - 32
2,6 - 3,2
III
1
level 4
4
yes
11 - 14
19 - 25
1,9 - 2,5
II
1
level 3
3
yes
4 - 10
7 - 18
0,7 - 1,8
I/II
1
level 2
2
yes
<4
<7
< 0,7
I
1
level 1
1
no
27
Filling with dishwasher salt
Rinse aid
Only use salt specifically designed for use in
dishwashers.
All other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water
softener.
Only fill with salt just before starting one of the complete
washing programmes.
This will prevent any grains of salt or salty water, which
may have been spilt, remaining on the bottom of the
machine for any period of time, which may cause
corrosion.
Rinse aid is automatically added during the last rinse, ensuring
thorough rinsing, and spot and streak free drying.
The dispenser, which is positioned inside the door, holds about
110 ml of rinse aid, which is sufficient for between 16 and 40
dishwashing cycles, depending upon the dosage setting.
Filling with rinse aid
1. Open the container by pressing the release button (A).
2. Add the rinse aid until the container is completely full. The
maximum level for filling is indicated by "max".
To fill:
1. Open the door, remove the lower basket and unscrew the
cap of the salt container by turning it anticlockwise.
2. Pour 1 litre of water inside the container (this is necessary
only before filling with salt for the first time).
3. Using the funnel provided,
pour in the salt until the
container is full.
4. Replace the cap making
sure that there is no trace
of salt on the screw
thread or on the gasket.
Ensure that the lid is closed after every refill.
Clean up any rinse aid spilt during filling with an
absorbent cloth to avoid excess foaming during the next
wash.
5. Replace the cap tightly
turning it clockwise until it
stops with a click.
Only use branded rinse aid for dishwashers. Never fill the
rinse aid dispenser with any other substances (e.g.
dishwasher cleaning agent, liquid detergent). This would
damage the appliance.
The salt container will require topping up periodically. You are
reminded of this by the salt indicator light on the control panel
which comes on when the salt has finished.
Adjusting the dose
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been
replenished, assuming the dishwasher remains switched
on. If you are using salts that take longer to dissolve then
this can take longer. The function of the machine is not
affected.
According to the finish and drying results obtained, adjust the
dose of rinse aid by means of the 6 position selector (position
1 minimum dosage, position 6 maximum dosage).
The dose is factory set in
position 4.
Increase the dose if there are
drops of water or lime spots
on the dishes after washing.
Do not worry if water overflows from the unit when filling with
salt, this is quite normal.
Reduce it if there are sticky
whitish streaks on the dishes
or a bluish film on glassware
or knife blades.
Top up the rinse aid when the indicator light on the control
panel illuminates.
28
In daily use
●
Check if it’s necessary to refill with dishwasher salt or rinse
aid
●
Load cutlery and dishes into the dishwasher.
●
Fill with dishwasher detergent .
●
Select a wash programme suitable for the cutlery and
dishes.
●
Start the wash programme.
Loading cutlery and dishes
Sponges, household cloths and any object that can
absorb water may not be washed in the dishwasher.
●
Before loading the dishes, you should:
- Remove all left over food and debris.
- Soften remnants of burnt food in pans
●
When loading the dishes and cutlery, please note:
- Dishes and cutlery must not impede the rotation of the
spray arms .
- Load hollow items such as cups, glasses, pans, etc. with
the opening downwards so that water cannot collect in the
container or a deep base.
- Dishes and items of cutlery must not lie inside one
another, or cover each other.
- To avoid damage to glasses, they must not touch.
- Lay small objects in the cutlery basket.
●
Plastic items and pans with teflon have a tendency to
retain water drops; these items will not dry as well as
porcelain and steel items.
For washing in the dishwasher the following cutlery/dishes
are of limited suitability:
are not suitable:
- Cutlery with wooden, horn, china or
mother-of-pearl handles
- Only wash stoneware in the dishwasher if it is specifically
marked as being dishwasher-safe by the manufacturer.
- Plastic items that are not heat resistant
- Glazed patterns may fade if machine washed frequently
- Older cutlery with glued parts that are not temperature
resistant
- Silver and aluminium parts have a tendency to discolour
during washing. Residues, e.g. egg white, egg yolk and
mustard often cause discolouring and staining on silver.
Therefore always clean left-overs from silver immediately, if
it is not to be washed straight after use.
- Bonded cutlery items or dishes
- Pewter or copper items
- Lead crystal glass
- Some types of glass can become dull after a large number
of washes
- Steel items prone to rusting
- Wooden platters
- Items made from synthetic fibres
Open the door and slide out the baskets to load the dishes.
The cutlery basket
Long bladed knives stored in an upright position are a
potential hazard.
Long and/or sharp items of cutlery such as carving knives
must be positioned horizontally in the upper basket.
Take care when loading or unloading sharp items such as
knives.
The lower basket
The lower basket is designed to take saucepans, lids, plates,
salad bowls, cutlery etc.
Serving dishes and large lids should be arranged around the
edge of the basket, ensuring that the spray arms can turn
freely.
Forks and spoons should be placed in the removable cutlery
basket with the handles facing downwards and the knives with
their handles facing upwards.
If the handles protrude from the bottom of the basket,
obstructing the lower spray arm, load the cutlery with the
handles facing upwards.
Mix spoons with other cutlery
to prevent them from sticking
together.
For best results we
recommend you to use the
cutlery grid provided (if the
size and dimensions of the
cutlery allow it).
29
The upper basket
Adjusting the height of the upper basket
The upper basket is designed for plates (dessert plates,
saucers, dinner plates of up to 24 cm in diameter), salad
bowls, cups and glasses.
Arrange items on and
underneath the cup racks so
that water can reach all
surfaces.
Glasses with long stems can
be placed upside down in the
cup racks.
For taller items, the cup racks
can be folded upwards.
Light items (plastic bowls
etc.) must be loaded in the
upper basket and arranged
so they do not move.
If washing very large plates you can load them in the lower
basket after moving the upper basket to the higher position.
Maximum height of the dishes in
upper basket
lower basket
With upper basket raised
20 cm
31 cm
With upper basket lowered
24 cm
27 cm
To move to the higher position proceed as
follows:
1. Move the front runner stops (A) of the upper basket
outwards and slide the basket out.
2. Refit the basket in the higher position and replace the stops
(A) in their original position.
When the basket is in the
higher position you will not
be able to use the cup
rack(s).
In case that plates are loaded in the upper
basket:
load them starting from the
rear positions of the basket;
tilting them slightly
forwards and avoiding the
front positions near the
door.
After loading your machine always close the door, as an
open door can be a hazard.
Before closing the door, ensure that the spray arms can
rotate freely.
30
Use of detergent
Different kinds of
detergent
Only use detergents specifically designed for use in
dishwashers.
Using no more than the correct amount of detergent
contributes to reducing pollution.
Detergent tablets
Please observe the manufacturer’s dosing and storage
recommendations as stated on the detergent packaging.
Detergent tablets from different manufactures dissolve at
different rates. For this reason, some detergent tablets do not
attain their full cleaning power during short washing
programmes. Therefore, please use long washing programmes
when using detergent tablets, to ensure the complete removal
of detergent residuals.
Fill with detergent
1. If the lid is closed: press release button (1). The lid springs
open.
2. Fill the detergent dispenser (2) with detergent.
The marking indicates the dosing levels:
20 = approximately 20 g of detergent
30 = approximately 30 g of detergent
Concentrated detergent
Modern detergents for dishwashers are almost exclusively lowalkaline concentrated detergents with natural enzymes in tablet
form.
Using 50°C washing programmes in conjunction with these
concentrated detergents reduces pollution and is good for your
dishes, as these washing programmes are specially matched
to the dirt-dissolving properties of the enzymes in concentrated
detergents. It is for this reason that using 50°C washing
programmes in conjunction with concentrated detergents can
achieve the same cleaning results that can otherwise only be
achieved using 65°C washing programmes.
3. All programmes with prewash need an additional detergent
dose (5/10 g) that must be placed in the prewash detergent
chamber (3). This detergent will take effect during the
prewash phase.
Use of "3 in 1" combi detergents
4. Close the lid and press until it locks in place.
1. Check whether these detergents are suitable for your water
hardness. Follow the manufacturers instructions.
These products are detergents with a combined cleaning,
rinsing and salt function.
2. Set the "3 in 1" function.
3. Before the start of the washing programme put the "3 in 1"
detergent in the detergent dispenser.
NOTE: If the drying results are not satisfactory we recommend
that you:
1. Fill up the rinse aid dispenser with rinse aid.
2. Activate the rinse aid dispenser and set the rinse aid
dosage to position 2.
If you decide to turn back to the use of the standard
detergent system we advise that you:
●
Deactivate the "3 in 1" function.
●
Fill up the dispensers for salt and rinse aid again.
●
Adjust the water hardness setting to the highest setting
and perform up to 3 normal washing programmes without
loading any dishes.
●
Adjust the water hardness setting according to the
hardness of the water in your area.
●
Adjust the rinse aid dosage.
NOTE: When using 4 in 1 detergents that integrate also antiglass corrosion agent into "3 in 1" formula, please follow the
same instruction as given for "3 in 1" detergents above.
31
Washing programmes
Programme
Degree of soil
and
type of load
Options available
with the
programme
Cycle
description
1 cold rinse (to avoid food scraps
from sticking together).
This programme does not require the
use of detergent.
(2) Consumption values
Energy
consumption
(in kWh)
Water
consumption
(in litres)
0,1
4
1.
Rinse and Hold
Any.
Partial load (to be completed
later in the day).
2.
Intensive 70°C
Heavy soil.
Crockery, cutlery, pots and
pans
half load
3 in 1
Hot prewash
Main wash up to 70°C
2 warm rinses
1 hot rinse
Drying
1,7 - 1,9
23 - 25
3.
Daily 65°C
Normal soil.
Crockery and cutlery
half load
3 in 1
Cold prewash
Main wash up to 65°C
2 warm rinses
1 hot rinse
Drying
1,5 - 1,7
23 - 25
4.
Quick Wash
60°C
Light soil.
Crockery and cutlery
3 in 1
Main wash up to 60°C
1 hot rinse
0,8
9
5.
Bio 50°C
with prewash
(1)
Normal soil.
Crockery and cutlery
half load
3 in 1
Cold prewash
Main wash up to 50°C
1 cold rinse
1 hot rinse
Drying
1,05
15
6.
Delicate 45°C
with prewash
Light soil.
Crockery , cutlery, pots and
pans
half load
3 in 1
Cold prewash
Main wash up to 45°C
1 cold rinse
1 hot rinse
Drying
1,0 - 1,1
14 - 16
7.
Crystal 40°C
Normal soil.
Delicate china, delicate
crockery and glassware
Main wash up to 40°C
1 warm rinse
1 hot rinse
Drying
0,8 - 0,9
14 - 16
3 in 1
(1) Testing programme for EN 50242 (see "Hints for Test Centres). This programme, developed for the use of detergents with enzymes, allows you
to achieve, with reduced consumption of energy the same cleaning results that would otherwise be obtained only with the 65°C programmes and
conventional detergents. To compensate the lower temperature, the duration of washing and drying have been extended.
(2) The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the variations of
the power supply. The programme duration is visible in the digital display when the selection of the washing programme occurs.
Note:
With the set of the half load option, programmes 2 (Intensive 70°C), 3 (Daily 65°C ) and 6 (Delicate 45°C withprewash) the prewash phase is
automatically excluded. (In this case the detergent dose for the prewash phase is no longer necessary).
With programme 5 (Bio 50°C with prewash) the duration of the washing phase will be reduced.
When using this option we recommend to reduce the dose of detergent that is normally used for a complete load.
32
Starting a washing programme
In this fully integrated appliance the controls are located on the
top of the door. When selecting a programme, the door needs
to be open.
Cancel a washing programme in progress
Open the dishwasher door.
Press simultaneously functio buttons 2 and 3 for about 2
seconds, the indicator light of the programme selection
button will illuminate and in the digital display will appear
two horizontal lines (--) indicating that the running
programme has been cancelled and that the machine has
returned to setting mode.
If a new washing programme is to be selected, check that
there is detergent in the detergent dispenser).
1. Check that the baskets have been
loaded correctly and that the spray
arms can rotate freely
2. Turn on the water tap
6. To cancel a delay start in progress
To cancel a delay start in progress you have to reset the
dishwasher; follow the same instructions given in "Cancel
a washing programme in progress".
Cancelling a delay start involves also the cancelling of the
set washing programme (and eventual options).
In this case you have to set the washing programme (and
options) again.
3. Press the On/Off button
The indicator light of the programme selection button will
illuminate and 2 horizontal lines (--) are visible in the digital
display.
4. Setting and starting the programme
To select a programme, press the programme selection
button until the number of the desired programme appears
in the digital display (see "Washing programmes" chart for
the number of the programme).
7. End of the washing programme
The dishwasher will automatically stop and an audible
signal informs you of the end of the washing programme.
Select, at the need, the options available with the selected
programme (see "Washing programmes" chart for
available options).
Open the dishwasher’s door, leave it ajar and wait a few
minutes before removing the dishes; in this way they will
be cooler and the drying will be improved.
Close the dishwasher’s door, the programme will start
automatically.
In the digital display is visible 0 (remaining running time).
The end of programme indicator light is illuminated.
Switch off the dishwasher by pressing the On/Off button.
Setting and starting the programme with the
delay start
8. Unloading the dishwasher
Once selected the washing programme (and options)
press the delay start button, the corresponding indicator
light will illuminate and in the digital display appears 1 h.
Hot dishes are sensitive to knocks. The dishes should
therefore be allowed to cool down before removing from
the appliance.
Empty the lower basket first and then the upper one; this
will avoid water dripping from the upper basket onto the
dishes in the lower one.
Water may appear on the sides and the door of the
dishwasher as the stainless steel will eventually become
cooler than the dishes.
Press the delay start button until in the digital display will
appear the number of hours desired (from 1 hour up to 19
hours).
Close the dishwasher’s door, the countdown starts
automatically and will decrease with steps of 1 hour.
The opening of the door will not modify or interrupt the
countdown.
When the washing programme has finished, it is
recommended that the dishwasher is unplugged and
the water tap turned off.
Once the delay start has elapsed the programme will start
automatically.
NOTE: The start of the programme o the countdown of
the delay start will occur only after the closure of the door,
until this moment you can modify the set made.
5. To interrupt or cancel a washing
programme in progress
Interrupt or cancel a washing programme in progress
ONLY if it’s absolutely necessary
Attention! Hot steam may escape when the door is
opened. Open the door carefully.
Interrupt a washing programme in progress
Open the dishwasher door; the programme will stop.
Close the door; the programme will start from the point at
which it was interrupted.
33
Maintenance and cleaning
Clean the external surfaces of the machine and control panel
with a damp soft cloth. If necessary use only neutral
detergents. Never use abrasive products, scouring pads or
solvent (acetone, trichloroethylene etc....).
Ensure that the seals around the door, the detergent and rinse
aid dispensers are cleaned regularly with a damp cloth.
We recommend every 3 months to run a 65°C wash
programme without dishes using detergent.
Attention!
Cleaning the filters
If residues of soil have
clogged the holes in the
upper spray arm, remove
them with a cocktail stick.
Under no circumstances may the dishwasher be used without
filters.
Incorrect repositioning and fitting of the filters will produce
poor washing results.
NEVER try to remove the
upper spray arm.
The filters must be checked and cleaned from time to time.
Dirty filters will degrade the washing result.
Important! Before cleaning the filters ensure that the
machine is switched off.
1. Open the door, remove the lower basket.
2. The dishwasher filter system comprises a coarse filter (A),
a microfilter (B) and a flat filter (C).
Unlock the filter system using the handle on the microfilter,
and remove.
Prolonged periods of non-operation
If you are not using the machine for any period of time you are
advised to:
1. Unplug the appliance and then turn off the water.
2. Leave the door ajar to prevent the formation of any
unpleasant smells.
3. Leave the inside of the machine clean.
Frost precautions
Avoid placing the machine in a location where the temperature
is below 0°C. If this is unavoidable, empty the machine, close
the appliance door, disconnect the water inlet pipe and empty
it.
3. Turn the handle about 1/4 a turn anticlockwise and remove.
Moving the machine
If you have to move the machine (moving house etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with the hoses.
Avoid over tilting the machine during transportation.
4. Take hold of the coarse filter (A) by the handle with
the hole and remove from the microfilter (B).
5. Clean all filters thoroughly under running water.
6. Remove the flat filter (C) from the base of the washing
compartment and clean both faces thoroughly.
7. Put the flat filter (C) back in the base of the washing
compartment.
8. Place the coarse filter (A) in the microfilter (B) and press
together.
9. Put the filter combination in place and lock by turning the
handle clockwise to the stop. During this process ensure
that the flat filter does not protrude above the base of the
washing compartment.
34
Something not working
Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions
given here, without calling out an engineer.
...a flashing fault code appears
The dishwasher will not start or stops during operation and a sequence of intermittent audible signals are heard.
Open the dishwasher’s door.
The intervention of an alarm is indicated by:
- the continuous flashing of the programme selection button,
- a fault code (as described in the chart) is visible in the digital display.
Carry out the following suggested corrective actions.
Fault code / malfunction
appears in the digital
display
The machine does not fill with
water.
appears in the digital
display
The dishwasher will not drain.
appears in the digital
display
Possible cause
Solutions
The water tap is blocked or furred with
limescale.
Clean the water tap.
The water tap is turned off.
Turn the water tap on.
The filter (where present) in the threaded hose
fitting at the water inlet valve is blocked.
Clean the filter in the threaded hose
fitting.
The water inlet hose has not been correctly laid
or it is bent or squashed.
Check the water inlet hose connection.
The sink spigot is blocked.
Clean out the sink spigot.
The water drain hose has not been correctly laid
or it is bent or squashed.
Check the water drain hose connection.
Anti-flood device is activated.
Close the water tap and contact your
local Service Force Centre.
Once the checks have been carried out, to continue the programme, press the programme selection button and close the door. The
programme will continue from the point at which it was interrupted. If the fault code reappears contact your local Service Force
Centre.
For other combinations of fault codes not described in the above chart will appear, please contact your local Service Force Centre.
...there are problems when operating the dishwasher
Malfunction
Possible cause
Solutions
The dishwasher door has not been properly
closed.
Close the door.
The main plug is not plugged in.
Insert the mains plug.
The fuse has blown in the household fuse box.
Replace the fuse.
For dishwasher models with delay start
option:
Delay start has been selected.
If dishes are o be washed immediately,
cancel the delay start.
The whistling is not a cause for concern.
Use a different brand of detergent.
The programme does not start
There is a whistling noise during
washing
35
...the wash results are not satisfactory
The dishes are not clean
●
●
●
●
●
●
●
●
The wrong washing programme has been selected.
The dishes were arranged in such a way as to stop water reaching all parts of the surface. The baskets must not be overloaded.
The spray arms do not rotate freely due to incorrect arrangement of the load.
The filters in the base of the washing compartment are dirty or incorrectly positioned.
Too little or no detergent has been used.
Where there are limescale deposits on the dishes; the salt container is empty or the incorrect level of the water softener has been
selected.
The drain hose connection is not correct.
The salt container cap is not properly closed.
The dishes are wet and dull
●
●
Rinse aid was not used.
The rinse aid dispenser is empty.
There are streaks, milky spots or a bluish coating on glasses and dishes
●
Decrease rinse aid dosing.
Water drops have dried onto glasses and dishes
●
●
Increase rinse aid dosing.
The detergent may be the cause. Contact the detergent manufacturer’s consumer care line.
If after all these checks, the problem persists, contact your
local Service Force Centre, quoting the model (Mod.) and
serial number (S.N.).
This information can be found on the rating plate located on
the side of the dishwasher door (see picture).
So that you always have
these numbers at hand, we
recommend you to make a
note of them here:
Mod. : . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . .
Service and spare parts
This product should be serviced by an authorised service
engineer, and only genuine spare parts should be used.
Under no circumstances should you attempt to repair the
machine yourself.
Repairs carried out by inexperienced persons may cause injury
or serious malfunctioning. Contact your local Service Force
Centre.
Always insist on genuine spare parts.
36
Hints for test centres
Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Washing
programmes" chart).
Test in accordance with EN 50242 must be carried out when the salt container and rinse aid dispenser have been filled with salt and
rinse aid respectively and using the test programme (see "Washing programmes" chart).
Load:
12 standard place settings
Rinse aid setting:
position 4 (Type III)
Detergent dosage :
5 g + 25 g (Type B)
Arrangement upper basket
Arrangement lower basket
Arrangement cutlery basket
Cup racks: position A
37
117996 29/1
Änderungen vorbehalten
Subject to change without notice
06/06