Zanussi | ZCC6600X | User manual | ZANUSSI ZCC6600W User Manual

ZANUSSI ZCC6600W User Manual
ELECTRIC
COOKER
ÇËÅÊÔÑÉÊÇ
ÊÏÕÆÉÍÁ
ZCC 6600
INSTRUCTION BOOKLET
ÖÕËËÁÄÉÏ ÏÄÇÃÉÙÍ
GR
ENGLISH
Important Safety Information
You MUST read these warnings carefully before installing or using the hob. If you need assistance,
contact our Customer Care Department.
Installation
•
•
•
•
•
•
•
•
•
•
The work of installation must be carried out by
competent and qualified installers according to the
regulations in force.
Any modifications to the domestic electrical mains
which may be necessary for the installation of the
appliance should be carried out only by competent
personnel.
Check your appliance for any transport damage.
Never connect a damaged appliance. If your appliance
is damaged, contact your supplier.
It is dangerous to modify, or attempt to modify, the
characteristics of this appliance.
Avoid installation of the appliance near inflammable
material (e.g. curtains, tea towels, etc.).
This appliance is heavy. Take care when moving it.
This appliance cannot be positioned on a base.
Remove all packaging before using the appliance.
Some parts have a shock-resistant plastic film
protection. Be sure to remove this plastic film before
you start operating the appliance and clean the parts
involved using a soft cloth wrung out in warm water
to which a little washing up liquid has been added.
Ensure that the electrical supply complies with the
type stated on the rating plate.
Child Safety
•
•
•
•
This appliance is designed to be operated by adults.
Do not allow children to play near or with the
appliance.
This appliance is not intended for use by children or
other persons whose physical, sensory or mental
capabilities or lack of experience and knowledge
prevents them from using the appliance safely without
supervision or instruction by a responsible person to
ensure that they can use the appliance safely.
The appliance gets hot when it is in use. Children
should be kept away until it has cooled.
Children can also injure themselves by pulling pans
or pots off the appliance.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
During Use
•
•
•
•
This appliance is intended for domestic cooking only.
It is not designed for commercial or industrial
purposes.
Do not use this appliance if it is in contact with water.
Do not operate the appliance with wet hands.
Ensure the control knobs are in the ‘OFF’ position
when not in use.
During use the appliance becomes hot. Care should
be taken to avoid touching heating elements inside
the oven.
Always stand back from the oven when opening the
oven door, to allow any build-up of steam or heat to
release.
When using other electrical appliances, ensure the
cable does not come into contact with the hot
surfaces of the appliance.
Never use the ceramic hob as a working space. Do
not store things on the ceramic hob.
Never use plastic or aluminium foil dishes on the
ceramic hob.
Never use plastic dishes in the oven. Never line any
part of the oven with aluminium foil.
Unstable or misshapen pans should not be used on
the cooking zones as unstable pans can cause an
accident by tipping or spillage.
The ceramic hob is shockproof, but not unbreakable!
Hard or pointed objects falling from a height can
damage the hob. If scratches or cracks are noticed,
disconnect the cooker from the electrical supply and
call you nearest Service Force Centre.
Never leave the appliance unattended when cooking
with oil and fats.
This appliance should be kept clean at all times. A
build-up of fats or foodstuffs could result in a fire.
Always ensure that the oven vent which is located at
the centre back of the hob is left unobstructed to
ensure ventilation of the oven cavity.
Perishable food, plastic items and areosols may be
affected by heat and should not be stored above the
appliance.
Only heat-resistant plates may be placed in the
drawer situated under the oven. Do not p ut
combustible materials there.
Never use steam or high pressure steam cleaners to
clean the appliance.
Do not use harsh abrasive cleaners or sharp metal
scraper to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Service
•
This appliance should only be repaired or serviced by
an authorised Service Engineer and only genuine
approved spare parts should be used.
3
Contents
For the User
For the Installer
Important Safety Information
3
Control Panel
5
Operation
6
Using the ceramic glass hob
7
Electric Oven
8
Before the First Use of the Cooker
9
Electric Programmer
10
Using the Oven
12
Hints and tips for using the oven
13
Defrosting
13
Cooking Chart - Conventional and fan cooking
14
Cooking Chart - Grilling
15
Cleaning the Ceramic Hob
16
Cleaning the Oven
17
Something not working
19
European Guarantee
22
Environmental Information
•
•
•
After installation, please dispose of the packaging
with due regard to safety and the environment.
When disposing of an old appliance, make it unusable,
by cutting off the cable.
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
Instructions for the Installer
20
Technical data
20
Electrical connections
21
Guide to Use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
!
Step by step instructions for an operation
Hints and Tips
Environmental Information
This appliance is manufactured according to
the following EEC directives:
2006/95 EEC - 93/68 EEC 89/336 EEC current edition.
Keep this instruction book for future
reference and ensure it is passed on to
any new owner.
These instruction are only valid in the
countries whose symbols appear on this
booklet’s cover.
4
Control Panel
1
1.
2.
3.
4.
5.
6.
7.
8.
9.
2
Front left cooking zone control knob
Back left cooking zone control knob
Back right cooking zone control knob
Front right cooking zone control knob
Electronic Programmer
Oven function control knob
Mains on Light
Oven Thermostat Pilot Light
Oven thermostat control knob
The Oven Cavity
Grill element
3
4
5
6
78
9
Storage Drawer
The storage drawer is located underneath the oven cavity.
During cooking the storage drawer may become
hot if the oven is on high for a long period of time,
therefore flammable materials such as oven gloves,
tea towels, plastic aprons etc. should not be
stored in the drawer.
Oven accessories such as baking sheets, will also
become hot, therefore care should be taken when
removing these items from the drawer whilst the
oven is in use or still hot.
Accessories
Oven Light
Oven Shelf
(x2)
Dripping Pan
(x1)
Oven fan
5
Operation
Push-Pull control knobs
Some models are provided with push-pull control knobs
(see picture). These knobs can be completely sunken
inside the control panel when the oven is not working.
Ceramic hob cooking zones
To switch on a cooking zone, turn the relevant control
knob clockwise to the required heat setting.
The control knob is numbered 0 - 9.
0 - OFF
9 - Maximum
The hob has two types of cooking zones:
Control knob for normal cooking zone
3 normal cooking zones (back left, back right
and front right)
We recommend the plates are switched to maximum (9)
for a short while to boost the cooking zone, and then
adjusted to the required setting.
1 double circuit cooking zone (front left)
The front left cooking zone has two heating elements.
-
To switch on the smaller circular cooking zone, turn
the relevant control knob clockwise to the required
heat setting.
- To switch on both heating elements, turn the control
knob clockwise to maximum heat setting (9) then
turn the knob further to nearly reach the "0" symbol.
You will hear a "click" and the wider cooking zone
will switch on. Then turn back the knob to position 9
and adjust it to the required heat setting.
Please be aware that the two heating elements will now
operate together, giving a higher power output than a
normal cooking zone.
Residual heat indicators
The hob is fitted with four residual heat indicators
corresponding to each cooking zone. The corresponding
indicator will remain on until the temperature falls below
30°C, even after the cooking zone is switched off.
When a cooking zone is switched on, a short
buzzing may be heard. This is quite normal and
does not affect the hob operation in any way.
Mains on Light
The mains on light will come on when the oven function
control knob and/or the cooking zone control knob are
set.
6
Control knob for double circuit cooking zone
Using the ceramic glass hob
Ceramic glass surface
The glass is hard, and has been tempered to withstand
heat, cold and temperature shocks. But like all glass it
is sensitive to impact. Do not stand on the ceramic glass
surface.
If scratches or cracks are noticed, disconnect
the cooker from the electrical supply to avoid
the possibility of electric shock and call you
nearest Service Force Centre.
Keep all objects and materials which can melt
away from the cooking surface, e.g. plastics,
aluminium foil.
Care should be taken when preparing food or drinks
containing sugar. If anything of this nature
accidentally comes into contact with the ceramic
surface it must be scraped off immediately while
still hot and wiped away to avoid damage to the
surface.
Energy consumption
To save energy, you should:
- use only cooking and frying utensils with smooth, flat
bases.
- place pots and pans in position before switching on
the cooking zone.
- wherever possible, cover pots and pans with a lid.
- switch off the cooking zone a few minutes before the
end of the cooking time, in order to make use of the
residual heat.
- use the residual heat of the cooking zones for keeping
food warm or for melting.
- position pots and pans centrally on the cooking zones.
Saucepans and frying pans
Saucepans and frying pans should not be smaller than
the cooking zone, and preferably not more than 10-15
mm larger than the diameter of the cooking zone.
Always use cooking and frying utensils with smooth, flat
bases.
The bases should always be clean and dry. Cook with a
lid in place.
Check that the bases of utensils are smooth and
undamaged; bases with burrs and sharp edges will
scratch the ceramic glass surface.
To avoid scratching or damaging the ceramic cooking
surface, pots and pans should be moved on the plate by
lifting them, and not by sliding.
Utensils with aluminium and copper bases can leave
behind metallic discolourations which can only be
removed with difficulty or sometimes not at all.
Take care when frying food in hot oil or fat,
as the overheated splashes could easily
ignite.
7
Electric Oven
Oven Function and Thermostat
control knobs
They enable to select the most appropriate type of
heating for the different cooking requirements by
appropriately connecting the heating elements and
adjusting temperature to the required level.
Conventional cooking - The heat comes from both
the top and bottom element, ensuring even
heating inside the oven.
Bottom heating element - The heat comes from
the bottom of the oven only.
Top heating element - The heat comes from the
top of the oven only.
Grill - The grill element will be on.
Fan cooking - This allows you to roast or roast and
bake simoultaneously using any shelf, without
flavour transference.
Defrost Setting - This setting is intended to assist
in thawing of frozen food.
Mains on Light
The mains on light will come on when the oven function
control knob and/or the cooking zone control knob are
set.
Thermostat Control Knob
Turn the thermostat control knob clockwise to select
temperatures between 50°C and 230°C (MAX).
Thermostat Control Light
The thermostat control light will come on when the
thermostat control knob is turned. The light will remain on
until the correct temperature is reached. It will then cycle
on and off to show the temperature is being maintained.
The Safety Thermostat
This oven is provided with a safety thermostat. In case of
malfunctioning of the main thermostat, and consequential
over-heating, the safety device will stop the power supply
to the appliance. If this happens, call your local Service
Force Centre. Under no circumstances should you
attempt to repair the appliance yourself.
8
Before the First Use of the Appliance
Remove all packaging, both inside and outside
the oven, before using the oven.
Before cooking for the first time, carefully wash
the oven accessories.
Before first use, the oven should be heated without food.
During this time, an unpleasant odour may be emitted.
This is quite normal.
The oven will work only if the time of day has
been set.
1. Set the time of day with the electronic programmer
(see chapter "Electronic Programmer").
2. Switch the oven function control knob to
!
.
conventional cooking
3. Set the thermostat control knob to MAX.
4. Open a window for ventilation.
5. Allow the oven to run empty for approximately 45
minutes.
This procedure should be repeated with the grill
function for approximately 5-10 minutes.
Once this operation is carried out, let the oven
cool down, then clean the oven cavity with a
soft cloth soaked in warm water to which a little
mild washing-up liquid has been added.
Using the ceramic hob for the
first time
The cooking surface should be cleaned before use to
remove any traces of the production process.
Wipe the ceramic surface and frame with a damp
cloth using warm water to which a little washing
up liquid has been added, and wipe dry.
!
Heating up for the first time
!
To check the cooking zones, briefly switch each
one on.
To open the oven door, always hold the
handle in the centre.
9
Electronic Programmer
4
1. Push button for selecting a function
5
6
7
8
2. Decreasing control button
3. Increasing control button
4. Display
5. “Cooking Duration” pilot lamp
6. “End of cooking” pilot lamp
2
1
3
7. “Minute minder” pilot lamp
8. “Time of day” pilot lamp
The oven will only work if the time of day has been set.
However, the oven can also be operated without any programme.
Setting the time of day
When the power supply is switched on, or after a power failure, the “Time of
day” pilot lamp
will flash on the display.
To set the correct time of day:
1. Press button
or
.
2. After the setting is carried out, wait for 5 seconds: the “Time of day”
will go out and the display will show the set time. The
pilot lamp
appliance is ready for use.
To reset the correct time of day:
1. Press button
repeatedly to select the “Time of day” function. The
relevant pilot lamp will start flashing. Then proceed as described above.
The time of day can only be reset if no automatic function (cook duration
or end of cooking
) has been set.
“Cooking Duration” function
This function allows the oven to automatically switch off at the end of a
programmed cooking duration time. Place food in the oven, select a cooking
function and adjust the cooking temperature. Press button repeatedly to
will start
select the “Cooking Duration” function. The relevant pilot lamp
flashing. Then, proceed as follows:
To set the duration time:
or
.
1. Press button
2. After the setting is carried out, wait for 5 seconds: the "Cooking Duration"
will come on and the display will revert to the time of day.
pilot lamp
3. When cooking time is over, the oven will be switched off automatically
and an acoustic alarm will be heard, while the pilot lamp will start flashing.
Turn the oven function and the thermostat control knob to zero.
To switch off the acoustic alarm, press any button.
NOTE: turning the acoustic alarm off will reset the oven to manual, and
if the oven function and the thermostat knobs are not set to zero the
oven will start to heat again.
To cancel the duration time:
1. Press button repeatedly to select the “Cooking Duration” function.
The relevant pilot lamp
will flash and the display will show the
remaining cooking time.
until the display shows “0:00”. After 5 seconds the
2. Press button
pilot lamp will go out and the display will revert to the time of day.
10
“End of cooking” function
With this function, you can set the oven to switch off automatically when a
programmed end of cooking time is over. Place food in the oven, select a cooking
function and adjust the cooking temperature. Press button
repeatedly to
select the “End of cooking” function. The relevant pilot lamp will start flashing.
Then, proceed as follows:
To set the End of cooking time:
or
.
1. Press button
2. After the setting is carried out, wait for 5 seconds: the “End of cooking” pilot
will come on and the display will revert to the time of day.
lamp
3. When cooking time is over, the oven will be switched off automatically and
an acoustic alarm will be heard, and the pilot lamp will start flashing. Turn
the oven function and the thermostat control knob to zero.
To switch off the acoustic alarm, press any button. NOTE: turning the acoustic
alarm off will reset the oven to manual, and if the oven function and the
thermostat knobs are not set to zero the oven will start to heat again.
To cancel the End of cooking time:
1. Press button
repeatedly to select the “End of cooking” function. The
relevant pilot lamp
will flash and the display will show the programmed
End of cooking time.
2. Press button
until the display shows the current time of day. The
programmer will beep and the pilot lamp will go out.
“Cooking duration”
time”
combined
and “End of cooking
The functions “Cooking duration” and “End of cooking time” can be used
simultaneously to set the oven to switch on and off automatically at a later time.
1. With the “Cooking duration” function (carry out the cooking duration setting
as described in the relevant chapter) set the duration time. Then, press
button : the display will show the programmed setting.
(carry out the End of cooking
2. With the “End of cooking time” function
setting as described in the relevant chapter) set the end of cooking time.
The relevant pilot lamps will come on and the display will show the time of
day. The oven will switch on and off according to the set programmes.
“Minute minder” function
The minute minder alarm will sound at the end of a timed period, but THE OVEN
WILL REMAIN ON, if it is in use.
To set the minute minder:
1. Press button
repeatedly to select the “Minute minder” function. The
relevant pilot lamp will start flashing.
or
(maximum: 2 hours, 30 minutes).
2. Then, press button
3. After the setting is carried out, wait for 5 seconds: the “Minute minder” pilot
lamp will come on.
4. At the end of the timed period, the pilot lamp will start flashing and an
acoustic alarm will be heard. To switch off the acoustic alarm, press any
button.
To cancel the minute minder:
1. Press button
repeatedly to select the “Minute minder” function. The
relevant pilot lamp will flash and the display will show the remaining time.
until the display shows “0:00”. After 5 seconds the pilot
2. Press button
lamp will go out and the display will revert to the time of day.
How to switch off the display
1. Press two or three programmer push buttons simoultaneously and keep
them pressed for about 5 seconds. The display will switch off.
2. To switch on the display, press any button.
The display can be switched off only if no other functions have been
set.
11
Using the Oven
Always cook with the oven door closed.
Stand clear when opening the drop down oven
door. Do not allow it to fall open - support the
door using the door handle, until it is fully open.
The oven has four shelf levels, and is supplied
with two shelves. The shelf positions are counted
from the bottom of the oven as shown in the
diagram.
It is important that these shelves are correctly
positioned as shown in the diagram.
Do not place cookware directly on the oven
base.
4
3
2
1
Attention! - Do not place objects on the oven base
and do not cover any part of the oven with
aluminium foil while cooking, as this could cause
a heat build-up which would affect the baking
results and damage the oven enamel. Always
place pans, heat-resisting pans and aluminium
trays on the shelf which has been inserted in the
shelf runners.
Carefully supervise cooking with fat or oil, since
these types of foodstuff can result in a fire, if overheated. For the same reason, be careful when
placing or removing food in the oven, not to let any
fat or oil fall on the oven base. If this happens,
carefully clean the oven to avoid unpleasant smells
or smoke.
Condensation and Steam
The oven is supplied with an exclusive system which
produces a natural circulation of air and the constant
recycling of steam. This system makes it possible
to cook in a steamy environment and keep the
dishes soft inside and crusty outside. Moreover,
the cooking time and energy consumption are
reduced to a minimum. During cooking steam may
be produced which can be released when opening
the oven door. This is absolutely normal.
However, always stand back from the oven
when opening the oven door during cooking or
at the end of it to allow any build up of steam
or heat to release.
If the steam comes into contact with a cool surface on
the outside of the oven, e.g. a trim, it will condense
and produce water droplets. This is quite normal and
is not a fault with the oven. To prevent discolouration,
regularly wipe away condensation and also soilage
from surfaces.
Cookware
•
Use any oven proof cookware which will withstand
temperatures of 230 °C.
• Baking trays, oven dishes, etc. should not be placed
directly against the grid covering the fan at the back of
the oven, or placed on the oven base.
• Do not use baking trays larger than 30 cm x 35 cm (12
in x 14 in) as they will restrict the circulation of heat
12 and may affect performance.
The effects of dishes
on cooking results
Dishes and tins vary in their thickness, conductivity,
colour, etc. which affects the way they transmit heat to
the food inside them.
A Aluminium, earthenware, oven glassware and bright
shiny utensils reduce cooking and base browning.
B Enamelled cast iron, anodized aluminium, aluminium
with non-stick interior and coloured exterior and dark,
heavy utensils increase cooking and base browning.
Hints and tips for using the oven
Hints and Tips on Cooking
Fish and Meat
You can place meat in oven proof dishes, or directly on the
oven shelf. In this case, remember to place the drip tray
in the first position from the bottom with some water in it.
The dripping pan will avoid the falling of melted fat on the
oven base.
White meat, poultry and fish in general, need to be
cooked at a medium temperature (between 150 and 175
°C). If you need to cook red meat (slightly browned on the
outside and more gently cooked in the inside), a higher
temperature (between 200 and 230 °C) for a short time is
recommended.
Hints and Tips on baking
Cakes usually need to be cooked at a medium temperature (between 150 and 200 °C).
A short oven pre-heating (about 10 minutes) is
recommeded when cooking cakes or baking. Once the
cooking has been started, keep the oven door closed
during all the cooking time, and check the cooking results
through the oven door glass.
Hints and Tips on grilling
If you need to grill meat or fish, place them directly on the
shelf after spreading a little oil on them.
In the grill function, heat comes only from the top element.
Therefore, you need to adjust the cooking level depending
on meat or fish's thickness.
Always remember to place the dripping pan in the lower
position with some water in it.
Defrosting
.
The oven fan operates without heat and circulates the
air, at room temperature, inside the oven. This increases
the speed of defrosting. However, please note that the
temperature of the kitchen will influence the speed of
defrosting.
This function is particularly suitable for delicate food which
could be damaged by heat, e.g. cream filled gateaux,
iced cakes, pastries, bread and other yeast products.
Hints and Tips
•
•
•
•
! How to Use Defrosting
Turn the oven function control knob to
ans set the
thermostat control knob to OFFposition #.
Cover food with a lid, aluminium foil or plastic film to
prevent drying out during defrosting.
ALWAYS COOK THOROUGHLY IMMEDIATELY
AFTER THAWING.
Frozen food should be placed in a single layer when
ever possible and turned over half way through the
defrosting process.
Only joints of meat and poultry up to 2 kg. (4 lb.) are
suitable for defrosting in this way.
Refer to the following table for approximate defrosting
times.
13
Cooking Chart
Cooking times do not include pre-heating time.
A short oven pre-heating (about 10 minutes) is necessary before any cooking.
Conventional and fan cooking
Weight (gr.)
Traditional Cooking
1000
500
500
250
1000
1200
1000
1500
1500
1500
1500
2000
1200
1200
1000
4000
1500
3000
1200
1500
800
1200
1500
Fan Oven
Cooking
time
TYPE OF DISH
Level
temp.
°C
Level
2
2
1
1
2
2
1
1
1
1
170
170
160
180
175
175
175
175
170
170
2
3
2
2
2
temp.
°C
minutes
2
2 (1 and 3)*
2
2 (1 and 3)*
2
2 (1 and 3)*
1
2
1
1
160
160
150
170
150
160
160
160
160
160
45 ~ 60
20 ~ 30
60 ~ 80
40 ~ 60
60 ~ 80
30 ~ 40
45 ~ 60
30 ~ 40
40 ~ 60
50 ~ 60
In cake mould on the shelf
In cake mould on the shelf
In cake mould on the shelf
In cake mould on the shelf
In cake tin on the shelf
In cake mould on the shelf
In cake mould
In cake mould on the shelf
In cake mould on the shelf
In cake mould on the shelf
170
190
100
190
200
2 (1 and 3)*
3
2
2
2 (1 and 3)*
160
170
100
180
190
25 ~ 35
15 ~ 25
90 ~ 120
12 ~ 20
15 ~ 25
In baking tray
In baking tray
In baking tray
In baking tray
In baking tray
1
1
2
1
190
190
200
200
2
1
2
2 (1 and 3)*
180
180
175
190
40 ~ 60
30 ~ 45
20 ~ 35
15 ~ 30
2 pieces in baking tray
In bread pan on the grid
6-8 rolls in baking tray
On baking tray on the grid
2
2
1
2
2
200
200
200
180
200
2 (1 and 3)*
2 (1 and 3)*
2 (1 and 3)*
2
2
175
175
180
160
175
40 ~ 50
45 ~ 60
35 ~ 45
45 ~ 65
40 ~ 55
In mould on the shelf
In mould on the shelf
In mould on the shelf
In mould on the shelf
In mould on the shelf
2
2
2
190
180
190
2
2
2
175
175
175
50 ~ 70
100 ~ 130
90 ~ 120
On shelf and dripping pan
On shelf and dripping pan
On shelf and dripping pan
2
2
2
2
2
2
2
2
2
2
2
2
2
210
210
210
180
180
190
190
180
175
175
190
190
190
2
2
2
2
2
2
2
2
2
2
2
2
2
200
200
200
170
160
175
175
160
160
160
175
175
175
50 ~ 60
60 ~ 70
70 ~ 80
120 ~ 150
100 ~ 120
110 ~ 130
60 ~ 80
210 ~ 240
120 ~ 150
150 ~ 200
60 ~ 80
150 ~ 200
90 ~ 120
On grid and dripping pan
On grid and dripping pan
On grid and dripping pan
With rind-in dripping pan
2 pieces-in dripping pan
Leg-in dripping pan
Whole-in dripping pan
Whole-in dripping pan
Whole-in dripping pan
Whole-in dripping pan
Cut in pieces
Cut in pieces
Whole
2
2
190
190
2 (1 and 3)*
2 (1 and 3)*
175
175
30 ~ 40
25 ~ 35
4
3
2
1
CAKES
Whisked recipes
Shortbread dough
Butter-milk cheese cake
Apple cake
Strudel
Jam-tart
Fruit cake
Sponge cake
Christmas cake
Plum cake
PASTRIES
Small cakes
Biscuits
Meringues
Buns
Pastry: Choux
BREAD AND PIZZA
White bread
Rye bread
Bread rolls
Pizza
FLANS
Pasta flan
Vegetable flan
Quiches
Lasagne
Cannelloni
MEAT
Beef
Pork
Veal
English roast beef
rare
medium
well done
Shoulder of pork
Shin of pork
Lamb
Chicken
Turkey
Duck
Goose
Rabbit
Hare
Pheasant
FISH
Trout/Sea bream
Tuna fish/Salmon
NOTES
4
3
2
1
3-4 fishes
4-6 fillets
(*) If you need to cook more than one dish at the same time, we recommend you to place them on the levels quoted
between brackets.
If you wish to cook more than one dish at the same time, we suggest that you change the cooking levels of your dishes
during the last 5-10 minutes in order to obtain a more uniform colour of your dishes.
14
Cooking times do not include pre-heating time.
A short oven pre-heating (about 10 minutes) is necessary before any cooking.
Grilling
Quantity
Level
TYPE OF DISH
Fillet steaks
Beef-steaks
Sausages
Pork chops
Chicken (cut in two)
Kebabs
Chicken (breast)
Hamburger
Fish (fillets)
Sandwiches
Toast
Pieces
Weight
4
4
8
4
2
4
4
6
4
4-6
4-6
800
600
—
600
1000
—
400
600
400
—
—
4
3
2
1
3
3
3
3
3
3
3
3
3
3
3
Temperature
Cooking time
(minutes)
°C
Upper
side
Lower
side
max
max
max
max
max
max
max
max
max
max
max
12 ~ 15
10 ~ 12
12 ~ 15
12 ~ 16
30 ~ 35
10 ~ 15
12 ~ 15
10 ~ 15
12 ~ 14
3~7
2~4
12 ~ 14
6~8
10 ~ 12
12 ~ 14
25 ~ 30
10 ~ 12
12 ~ 14
8 ~ 10
10 ~ 12
—
2~3
The oven temperatures are intended as a guide only. It may be necessary to increase or decrease the
temperatures to suit individual preferences and requirements.
15
Cleaning the Ceramic Hob
Before any maintenance or cleaning can be carried
out, you must DISCONNECT the cooker from the
electricity supply.
Never use steam or high pressure steam cleaners
to clean the appliance.
Before cleaning, make sure the hob is cool.
Never use aggressive or abrasive agents, such as oven
sprays, stain or rust removers, scouring powders, or
sponges with an abrasive effect.
Special cleaning agents such as Hob Brite and ceramic
hob scrapers are available from your local Service Force
Centre.
Cleaning after each use
Slight, non-burnt soilage can be wiped off with a damp
cloth. Burnt soilage has to be removed with a scraper.
Afterwards wipe off the ceramic hob with a damp cloth,
and Hob Brite.
Stain removal
Light metallic stains (aluminium residues) can be
removed from the cooking zone with a ceramic hob
cleaning agent such as Hob Brite when cool.
Sugar solutions, food stuffs with a high sugar content
must be removed immediately with a scraper. If this type
of soilage is not removed immediately it can cause
irreparable damage to the ceramic surface. When the
surface has cooled wipe over with a damp cloth and Hob
Brite.
Before using any detergent or cleaning agent on the
ceramic top, ensure they are recommended by the
manufacturer for use on ceramic hobs.
Do not apply any cleaning agents to hot cooking zones.
Ensure any residues are wiped off before the cooking
zones are used again.
Special problems
If a chemical cleaner proves inadequate
Check whether the use of a scraper is more effective.
• when darks stains occur
If the use of a scraper and a ceramic hob cleaner proves
unsuccessful, your hob surface may have been damaged by
using unsuitable cleaning agents, or by pan bases with a
scouring effect. This will not impair the efficiency of your
ceramic hob.
• when metallic discolourations appear on
the cooking zone
Pots and pans with unsuitable bottoms, or unsuitable cleaning
agents have been used. The discolourations can only be
removed with considerable effort, using a ceramic glass
cleaner.
• when the surface shows scratches
These may be caused by scraping or melted on objects and
cannot be removed. This will not impair the efficiency of your
ceramic hob
16
Cleaning the Oven
The oven should be kept clean at all times. A
build-up of fats or other foodstuffs could result in
a fire, especially in the grill pan.
Cleaning materials
Before using any cleaning materials on your oven, check
that they are suitable and that their use is recommended
by the manufacturer.
Cleaners that contain bleach should NOT be used as
they may dull the surface finishes. Harsh abrasives should
also be avoided.
• Never use steam or steam machines to clean the
appliance.
External cleaning
Regularly wipe over the control panel, oven door and door
seal using a soft cloth well wrung out in warm water to
which a little washing up liquid has been added.
To prevent damaging or weakening the door glass
panels avoid the use of the following:
•
•
Household detergent and bleaches
Impregnated pads unsuitable for non-stick
saucepans
• Brillo/Ajax pads or steel wool pads
• Chemical oven pads or aerosols
• Rust removers
• Bath/Sink stain removers
Clean the outer and inner door glass using warm soapy
water. Should the inner door glass become heavily soiled
it is recommended that a cleaning product such as Hob
Brite, or Bar Keepers Friend is used.
Oven lamp replacement
Disconnect the appliance from the electricity
supply.
If the oven bulb needs replacing, it must comply with
the following specifications: electric power, 15 W/25 W;
electric rate, 230 V (50 Hz); resistant to temperatures
of 300°C; connection type: E14. These bulbs are
available from your local Service Force Centre.
!
To replace the faulty bulb:
1. Ensure the oven is disconnected from the electrical
supply.
2. Turn the glass cover anticlockwise.
3. Remove the faulty bulb and replace it with the new
one.
4. Refit the glass cover.
5. Reconnect to the electrical supply.
17
Oven Cavity
The enamelled oven cavity is best cleaned whilst the
oven is still warm.
Wipe the oven over with a soft cloth soaked in warm
soapy water after each use. From time to time it will be
necessary to do a more thorough cleaning, using a
proprietary oven cleaner.
Oven Shelves
To clean the oven shelves, soak in warm soapy water
and remove stubborn marks with a well wetted soap
impregnated pad. Rinse well and dry with a soft cloth.
The Oven Door and its gasket
Before cleaning the oven door, we recommend you to
remove it from the oven.
Proceed as follows:
1. open the oven door completely;
2. find the hinges linking the door to the oven (see
picture 1);
3. unlock and turn the small levers located on the two
hinges (see picture 2);
4. handle the door by its left- and right-hand sides,
then slowly turn it towards the oven until it is halfclosed (see picture 3);
5. gently pull the oven door off its site (see picture 3);
6. place it on a steady plan;
Clean the oven door glass with warm soapy water and a
softh cloth only. Never use harsh abrasives.
Once the cleaning is carried out, refit the oven door,
following the procedure in reverse.
DO NOT clean the oven door while the glass
panels are warm. If this precaution is not observed
the glass panel may shatter.
If the door glass panel becomes chipped or has
deep scratches, the glass will be weakened and
must be replaced to prevent the possibility of the
panel shattering. Contact your local Service Centre
who will be pleased to advise further.
Models in stainless steel or aluminium:
We recommend to clean the oven door using only a wet
sponge and dry it up after cleaning with a soft cloth.
Never use steel wool, acids or abrasive products as they
can damage the oven surface.
Clean the oven control panel following the same
precautions.
The correct operation of the oven is ensured by a gasket
placed round the edge of the oven cavity.
•
Periodically check the condition of this gasket. If
necessary, clean it without using abrasive cleaning
products.
•
If the gasket shows to be damaged, call you local
Service Centre. Do not use the oven until it has been
repaired.
18
1
2
3
Something not working
If the appliance is not working correctly, please carry out the following checks, before contacting your local Service
Force Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation,
a charge will be made even if the appliance is under guarantee.
SYMPTOM
! The cooker does not operate.
SOLUTION
" Check that the unit is plugged in and the electrical
supply is switched on.
" Check the mains fuse has not blown.
" Check the correct control knob has been turned.
! The ceramic hob is not giving satisfactory results.
" Check the cooking pan is the correct size for the
cooking zone.
" Check the cooking pan has a flat base.
" Check the setting is correct for the type of cooking.
! The oven does not come on.
" Check that a cooking function has been selected.
" Check that the oven door is completely closed.
" Check that the time of day has ben set (see
chapter "How to set the time of day").
" Check that the socket switch or the switch from the
mains supply to the cooker are ON.
! The oven light does not come on.
" Select a function with the oven function control
knob.
" Check the light bulb, and replace it if necessary
(see "Oven Lamp replacement").
! It takes too long to finish the dishes, or they are
cooked too fast.
! Steam and condensation settle on the food and the
oven cavity.
! The oven fan is noisy.
" The temperature may need adjusting.
" Refer to the contents of this booklet, especially to
the chapter “Using the Oven”.
" Leave dishes inside the oven no longer than 15-20
minutes after the cooking is completed.
" Check that shelves and bakeware are not vibrating
in contact with the oven back panel.
! The display shows "12.00".
" Set the time of day (see chapter "How to set the
time of day").
If after all these checks, the cooker still does not work, contact your local Service Force Centre.
Service and Spare Parts
If after the checks listed in the previous chapter, the
appliance still does not work correctly, contact your
locals Service Centre, specifying the type of
malfunctioning, the appliance model (Mod.), the product
number (Prod. No.) and the serial number (Ser. No.)
marked on the identification plate.
This plate is placed on the front external edge of the oven
cavity.
Original spareparts, certified by the
product manufacturer and carrying
this symbol are only available at our
Service Centre and authorized
spareparts shops.
19
Instructions for the Installer
Technical Data
Oven
Appliance Class 2 sub class 1 and Class 1
Oven elements
1,800 W
Dimensions
Bottom heating element
1,000 W
Height
900 mm
Depth
600 mm
Width
600 mm
Oven Capacity
53 l
Top heating element
800 W
Grill element
1,650 W
Convection heating element
2,000 W
Convection fan
25 W
Oven light
25 W
Total rating
2,050 W
Front left cooking zone 1,700 W / Ø180 mm-110 mm
Back left cooking zone
1,200 W / Ø145 mm
Back right cooking zone
1,700 W / Ø180 mm
Front right cooking zone
1,200 W / Ø145 mm
Total rating
5,800 W
Total cooker rating (hob + oven)
7,850 W
Installation
Levelling
The following instructions are meant for a qualified
installer, in order that the operations of installation,
regulation, and service are executed according to the
existing regulations.
Whenever changes are mode involving the disconnection
of the machine it is necessary to proceed with maximum
caution.
The appliance is provided with adjustable small feet
placed in the back corners of the base. By adjusting the
small feet it is possible to change the height of the
appliance so as to ensure a uniform distribution of the
liquids contained in pans or pots.
Ceramic Hob
THE MANUFACTURING COMPANY DECLINES
ANY RESPONSABILITY FOR POSSIBLE
DAMAGES
RESULTING FROM AN INSTALLATION WHICH
DOESN'T COMPLY WITH THE RULES IN FORCE
Installation environnement
Installation and maintenance must be carried out by a
qualified technician, in compliance with rules in force.
The electric coonection must be carried out in
compliance rules in force.
Our responsability will not be involved in case of
accidents caused by a defective or non existent
earth connection.
Positioning
The appliance has been designed to be placed between
two furniture units whose height does not exceed the
cooker's plate height.
20
Supply voltage (50 Hz)
230 V/400 V 3N~
Electrical connection
Prior to making the electric al connection, make sure
that:
- The protection fuse and the domestic wire system
are suitable to carry the total electric load of the oven
(see rating plate).
-
Your domestic wiring system has an efficient earth
connection in compliance with the rules and laws in
force.
-
The wall socket or the omnipole switch used for the
electrical connection can easily be reached after the
oven is built in.
The appliance is delivered without an electric supply cable,
therefore, you will have to fit to it a supply cable with
standard plug, suitable for the total electric load shown
on the rating plate.
The plug is to be inserted into a suitable wall socket.
If you require a direct connection to the electric network
(mains), it will be necessary to fit between the appliance
and the mains an omnipole switch, aith a minimum gap
between contacts of 3 mm. suitable for the required load
and in compliance with rules in force. The green 1 yellow
ground wire must not be interrupted by the switch.
The supply cable must in all cases be laid out in such a
way as to ensure that it does not reach at any given
point a temperature 50°C higher than the ambient temperature.
The manufacturer disclaims any liability in case these
accident-preventing rules are not observed.
Suitable power supply cables are the following types,
considering the respective necessary section of cable.
•
•
•
•
•
H07 RN-F
H05 RN-F
H05 RR-F
H05 VV-F
H05 V2V2-F (T90)
Connecting the terminal board
The appliance incorporates an easily accessible 6-pole
terminal board whose jumpers (bridges) are already preset for operation on 400 V three-phase with neutral wire.
In case where different mains voltage is present, the
jumpers on the terminal board must be arranged as shown
in the diagram.
.
The ground cable must be connected to terminal
After connecting the supply cable to the terminal board,
secure it with a junction clamp.
230V 3~
230V 1~
400V 2N~
400V 3N~
1 2 3 4 5
L1
L2
L3 PE
1 2 3 4 5
L1
N
1 2 3 4 5
PE
L1 L2
N
1 2 3 4 5
PE
L1 L2 L3 N
PE
Section
of cable
(min.)
4 x 1.5 mm2
Section
of cable
(min.)
3 x 2.5 mm2
Section
of cable
(min.)
4 x 2.5 mm2
Section
of cable
(min.)
5 x 1.5 mm2
21
European Guarantee
This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the
period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of
the countries listed below the appliance guarantee will move with you subject to the following qualifications:
•
The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of a valid purchase document issued by the seller of the appliance.
•
The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your new
country of residence for this particular model or range of appliances.
•
The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred to another
user.
•
The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within
the home, i.e. is not used for commercial purposes.
•
The appliance is installed in accordance with all relevant regulations in force within your new country of residence.
The provisions of this European Guarantee do not affect any of the rights granted to you by law.
22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising