Yamaha NS-50 OWNER'S MANUAL

Yamaha NS-50 OWNER'S MANUAL
NS-50
Natural Sound 3-way, 4-speaker Bass Reflex Speaker System
Thank you for selecting this Yamaha NS-50 speaker system.
PRECAUTIONS
Read these precautions carefully before using your speaker.
● Any time you note distortion, reduce the volume control on
your amplifier to a lower setting. Never allow your amplifier to
be driven into “clipping”. Otherwise the speaker may be
damaged.
● When using an amplifier with a rated output power higher than
the nominal input power of the speaker, care should be taken
never to exceed the speaker’s maximum input.
● Do not attempt to clean the speaker with chemical solvents as
this might damage the finish. To clean, wipe with a dry, soft
cloth.
● To prevent the enclosure from warping or discoloring, do not
place the speaker where it will be exposed to direct sunlight or
excessive humidity.
● Do not place the speaker where it is liable to be knocked over
or struck by falling objects. Stable placement will also ensure
better sound performance.
● Placing the speaker on the same shelf or rack as the turntable
can result in feedback.
● Secure placement or installation is the owner’s
responsibility.
YAMAHA shall not be liable for any accident caused by
improper placement or installation of the speaker.
CONNECTION TO YOUR AMPLIFIER
BEFORE MAKING CONNECTIONS, MAKE SURE THAT THE
AMPLIFIER IS SWITCHED OFF.
■ CONNECTIONS
● Connect the push-type input terminals at the rear of the
speakers to the speaker output terminals of your amplifier with
the provided speaker cables.
● One side of the speaker cable is red and the other side is
black. Connect the (+) terminals on both the amplifier and the
speakers using this red side. Connect the (–) terminals on both
components using the black side of the cable.
● Connect one speaker to the left (marked L) terminals of your
amplifier, and another speaker to the right (marked R)
terminals, making sure not to reverse the polarity (+, –). If one
speaker is connected with reversed polarity, the sound will be
unnatural and lack bass.
Procedures:
➀ Press the tab on the terminal down, as shown in the figure.
➁ Insert the bare speaker wire end properly into the terminal
hole. [Remove approx. 5 mm (1/4”) insulation from the
speaker cable.]
➂ Remove your finger from the tab to allow it to lock snugly on
the cable’s wire end.
➃ Test the security of the connection by tugging lightly on the
cable at the terminal.
Red line
Press tab
Speaker (R)
Black line
Speaker (L)
Red line
Black line
Speaker output
terminals of the
amplifier
Note
Do not let the bare speaker wires touch each other as this
could damage the speaker and/or the amplifier.
PLACING THE SPEAKER
SPECIFICATIONS
● Place the speakers on a sturdy, vibration-free surface. If you
cannot obtain good bass quality when the speakers are placed
directly on the floor, insert a block etc. between the speakers
and the floor.
Type .......................3-way 4-speaker bass reflex speaker system
Speaker Unit..............................................20 cm cone woofer x 2
10 cm cone midrange
5 cm cone tweeter
Input Terminal ...............................................................Push-type
Nominal Impedance ...........................................................6 ohms
Frequency Response............................................40 Hz – 20 kHz
Nominal Input Power ..............................................................70W
Music Input Power................................................................250W
Sensitivity .....................................................................90 dB/w/m
Crossover Frequency..............................................700 Hz, 4 kHz
Dimensions (WxHxD)....................................280 x 900 x 285 mm
............................................................(11” x 35-7/16” x 11-1/4”)
Weight .........................................................13.7 kg (30 lbs. 4 oz.)
Accessories ..............................................Speaker cable (4m) x 2
● Better stereo images will be obtained when the speakers are
slightly angled in towards the listeners.
* Specifications subject to change without notice due to product
improvements.
* Care should be taken not to exceed the input power values
noted above.
Note
Bacause this speaker is not a magnetic shielding type,
there may be some influence on a TV picture depending on
the type of TV or the placement of the speaker. In such a
case, place the speaker apart from the TV so that there is no
influence on TV picture.
REMOVING THE FRONT COVER
The front cover is fastened to the enclosure at four points, and
can be removed if desired. To remove the cover, hold on to both
sides and slowly pull straight away from the speaker. To
reattach, line up the four pegs on the inside surface of the cover
with the four corresponding holes on the speaker and push
gently.
Note
When the cover is removed, take care not to touch the
speaker units with your hands or to exert excessive force
with tools.
VU 89840
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement