Yamaha RX-V1700 Owners Manual

Yamaha RX-V1700 Owners Manual
RX-V1700_U-cv.fm Page 1 Monday, May 8, 2006 3:54 PM
U
RX-V1700
RX-V1700
AV Receiver
© 2006
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WH63550
01EN_00_RX-V1700_U.book Page i Tuesday, June 27, 2006 9:37 AM
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
10
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1
2
3
4
5
6
7
8
9
i
11
Read Instructions – All the safety and operating instructions
should be read before the product is operated.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions – All operating and use instructions
should be followed.
Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to
overturn.
12
13
14
15
16
17
18
19
Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
01EN_00_RX-V1700_U.book Page ii Tuesday, June 27, 2006 9:37 AM
IMPORTANT SAFETY INSTRUCTIONS
d)
20
21
22
23
If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f)
When the product exhibits a distinct change in
performance - this indicates a need for service.
Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24
Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
ii
01EN_00_RX-V1700_U.book Page iii Tuesday, June 27, 2006 9:37 AM
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any damage
resulting from use of this unit with a voltage other than
specified.
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reasons.
iii
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
17 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
18 Before moving this unit, press MASTER ON/OFF to release it
outward to the OFF position to turn off this unit, the main
room, Zone 2 and Zone 3 and then disconnect the AC power
plug from the AC wall outlet.
19 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC wall outlet. Voltages are:
Asia model ............................ 220/230–240 V AC, 50/60 Hz
General model ........ 110/120/220/230–240 V AC, 50/60 Hz
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
As long as this unit is connected to the AC wall outlet,
it is not disconnected from the AC power source even
if you turn off this unit by MASTER ON/OFF. In this
state, this unit is designed to consume a very small
quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
POUR LES CONSOMMATEURS CANADIENS
Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante de
la prise et pousser jusqu’au fond.
Cet appareil numérique de la classe B est conforme à
la norme NMB-003 du Canada.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
01EN_00_RX-V1700_U.book Page 1 Tuesday, June 27, 2006 9:37 AM
CONTENTS
FEATURES............................................................. 2
GETTING STARTED............................................ 3
Supplied accessories .................................................. 3
CONTROLS AND FUNCTIONS ......................... 4
PREPARATION
CONNECTIONS .................................................. 13
Using AUTO SETUP .............................................. 32
BASIC OPERATION
Basic procedure ....................................................... 38
Selecting audio input jacks (AUDIO SELECT)...... 40
Selecting the MULTI CH INPUT component......... 41
Using your headphones............................................ 41
Muting the audio output........................................... 41
Displaying the input source information ................. 42
Playing video sources
in the background of an audio source.................. 43
Using the sleep timer ............................................... 43
SOUND FIELD PROGRAMS............................. 44
Selecting sound field programs ............................... 44
Sound field program descriptions............................ 45
Enjoying unprocessed input sources........................ 49
USING AUDIO FEATURES............................... 50
Enjoying pure hi-fi sound ........................................ 50
Adjusting the tonal quality....................................... 50
Adjusting the speaker level...................................... 51
Enjoying multi-channel sources
in 2-channel stereo............................................... 51
Selecting the Compressed Music
Enhancer mode .................................................... 52
Selecting the night listening mode........................... 53
USING iPod ...........................................................73
Controlling iPod ...................................................... 73
RECORDING ........................................................75
ADVANCED OPERATION
ADVANCED SOUND CONFIGURATIONS.....76
Changing sound field parameter settings................. 76
Selecting decoders ................................................... 80
CUSTOMIZING THIS UNIT
(MANUAL SETUP) ..........................................84
Using SET MENU................................................... 86
1 BASIC MENU...................................................... 87
2 SOUND MENU.................................................... 91
3 INPUT MENU...................................................... 94
4 OPTION MENU................................................... 97
REMOTE CONTROL FEATURES .................101
Controlling this unit, a TV,
or other components .......................................... 101
Setting remote control codes ................................. 103
Programming codes from other remote controls ... 105
Changing source names in the display window..... 106
Macro programming features ................................ 107
Clearing configurations ......................................... 110
USING MULTI-ZONE CONFIGURATION ...113
Connecting the Zone 2 and Zone 3 components ... 113
Controlling Zone 2 or Zone 3 ................................ 114
ADVANCED SETUP ..........................................117
Using ADVANCED SETUP ................................. 117
Setting remote control ID ...................................... 119
ADDITIONAL INFORMATION
TROUBLESHOOTING .....................................122
RESETTING THE SYSTEM.............................130
GLOSSARY.........................................................131
SOUND FIELD PROGRAM
INFORMATION .............................................134
PARAMETRIC EQUALIZER
INFORMATION .............................................135
SPECIFICATIONS.............................................136
APPENDIX (at the end of this manual)
• SOUND OUTPUT IN EACH SOUND FIELD
PROGRAM
• LIST OF REMOTE CONTROL CODES
1 En
ADDITIONAL
INFORMATION
PLAYBACK.......................................................... 38
Connecting the XM Passport System ...................... 61
XM Satellite Radio controls and functions.............. 62
Activating XM Satellite Radio ................................ 63
Basic XM Satellite Radio operations....................... 65
Setting the XM Satellite Radio preset channels ...... 70
Displaying the XM Satellite Radio information...... 71
ADVANCED
OPERATION
AUTO SETUP....................................................... 32
XM SATELLITE RADIO TUNING ...................61
BASIC
OPERATION
Placing speakers....................................................... 13
Connecting speakers ................................................ 14
Using bi-amplification connections......................... 17
Information on jacks and cable plugs ...................... 18
Information on HDMI.............................................. 19
Audio and video signal flow.................................... 20
Connecting a TV monitor or projector .................... 21
Connecting other components ................................. 22
Connecting a multi-format player
or an external decoder ......................................... 26
Connecting a YAMAHA iPod universal dock ........ 27
Using the VIDEO AUX jacks on the front panel .... 27
Connecting the FM and AM antennas ..................... 28
Connecting the power cable..................................... 29
Setting the speaker impedance................................. 30
Turning on and off the power .................................. 31
FM/AM controls and functions ............................... 54
Automatic tuning ..................................................... 55
Manual tuning.......................................................... 56
Automatic preset tuning........................................... 57
Manual preset tuning ............................................... 58
Selecting preset stations........................................... 59
Exchanging preset stations ...................................... 60
PREPARATION
Front panel ................................................................. 4
Remote control........................................................... 6
Zone 2/Zone 3 remote control ................................... 8
Preparing the remote control ..................................... 9
Front panel display .................................................. 10
Rear panel ................................................................ 12
FM/AM TUNING..................................................54
INTRODUCTION
INTRODUCTION
01EN_00_RX-V1700_U.book Page 2 Tuesday, June 27, 2006 9:37 AM
FEATURES
FEATURES
Built-in 7-channel power amplifier
iPod controlling capability
◆ Minimum RMS output power
(20 Hz to 20 kHz, 0.04% THD, 8 Ω)
Front: 130 W + 130 W
Center: 130 W
Surround: 130 W + 130 W
Surround back: 130 W + 130 W
◆ DOCK terminal to connect a YAMAHA iPod universal dock
(such as the YDS-10, sold separately), which supports iPod
(Click and Wheel), iPod nano, and iPod mini
Sound field programs
◆ Proprietary YAMAHA technology for the creation of sound
fields
◆ Dolby Digital/Dolby Digital EX decoder
◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6,
DTS 96/24 decoder
◆ Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx
decoder
◆ Neural Surround decoder (U.S.A. and Canada models only)
◆ Virtual CINEMA DSP
◆ SILENT CINEMA
Sophisticated AM/FM tuner
◆ 40-station random and direct preset tuning
◆ Automatic preset tuning
◆ Preset station shifting capability (preset editing)
XM Satellite Radio
(U.S.A. and Canada models only)
◆ XM Satellite Radio tuning capability (using the “XM Passport
System” sold separately)
◆ Neural Surround decoder to play back the surround sound
content of XM Satellite Radio broadcasts in multi-channels,
resulting in a full surround sound experience
Other features
◆ YPAO (YAMAHA Parametric Room Acoustic Optimizer) for
automatic speaker setup
◆ 192-kHz/24-bit D/A converter
◆ OSD (on-screen display) menus that allow you to optimize
this unit to suit your individual audiovisual system
◆ 6 or 8-channel additional input jacks for discrete multichannel input
◆ Analog video interlace/progressive conversion from 480i
(NTSC)/576i (PAL) to 480p/576p
◆ S-video signal input/output capability
◆ Component video input/output capability includes (3
COMPONENT VIDEO INs and 1 MONITOR OUT)
◆ Optical and coaxial digital audio signal jacks
◆ Pure Direct mode for pure hi-fi sound for all sources
◆ Cinema and music night listening modes
◆ Compressed Music Enhancer mode to improve the sound
quality of compression artifacts (such as the MP3 format) to
that of a high-quality stereo
◆ Remote control with preset remote control codes, learning and
macro capability
◆ ZONE 2/ZONE 3 custom installation facility
◆ Zone switching capability between the main zone and
ZONE 2/ZONE 3 using ZONE CONTROLS
◆ Sleep timer
HDMI (High-Definition Multimedia Interface)
◆ HDMI interface for standard, enhanced or
high-definition video (includes 1080p video signal
transmission) as well as multi-channel digital audio based on
HDMI version 1.2a
◆ Analog video to HDMI digital video up-conversion
(composite video ↔ S-video ↔ component video → HDMI
digital video) capability for monitor out
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
Manufactured under license from Digital Theater Systems, Inc.
“DTS”, “DTS-ES”, “NEO:6”, and “DTS 96/24” are trademarks
of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital
Theater Systems, Inc. All right reserved.
iPod®
“HDMI”, the “HDMI” logo and “High-Definition Multimedia
Interface” are trademarks or registered trademarks of HDMI
Licensing LLC.
“SILENT CINEMA” is a trademark of YAMAHA
CORPORATION.
The XM name and related logos are registered trademarks of XM
Satellite Radio Inc.
“iPod” is a trademark of Apple Computer, Inc., registered in the
U.S. and other countries.
Neural Surround™ name and related logos are trademarks owned
by Neural Audio Corporation.
2 En
01EN_00_RX-V1700_U.book Page 3 Tuesday, June 27, 2006 9:37 AM
GETTING STARTED
GETTING STARTED
INTRODUCTION
Supplied accessories
Check that you received all of the following parts.
Remote control
POWER
POWER
TV
AV
XM
PHONO
TUNER
V-AUX/DOCK CBL/SAT
DTV
VCR 1
STANDBY
POWER
AUDIO SEL
SLEEP
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
Zone 2/Zone 3
remote control
(except Europe model)
POWER
XM
TUNER
SELECT
1
DTV
AMP
+
+
+
TV VOL
CH
VOLUME
SOURCE
–
–
–
TV MUTE
TV INPUT
MUTE
LEVEL
PRESET/CH
CD
CD-R
2
3
STANDBY
CBL/SAT MD/TAPE PHONO
5
4
VCR 1 DVR/VCR 2
7
6
ENT
DVD
V-AUX/DOCK
9
0
8
TV
SET MENU
TITLE
PURE DIRECT
Batteries (6)
(AAA, R03, UM-4)
VOLUME
PRESET
MENU
SRCH MODE
BAND
A/B/C/D/E
AUDIO
ENTER
MUTE
A-E/CAT.
PARAMETER
STRAIGHT
A-E/CAT.
DISPLAY
RETURN
EFFECT
XM MEMORY
CLASSICAL
LIVE/CLUB
ENTERTAIN
2
3
4
SUR. DECODE
SELECT
EXTD SUR.
5
6
0
9
DISPLAY
MOVIE
1
STEREO
7
8
NIGHT
ENHANCER
+ 10
ENT
PRESET/CH
ALL
PRESET
ID1 ID2
CAT.
ZONE 2 ZONE 3
NUMBER
REC
DISC SKIP
OFF
ON
MACRO
LEARN
CLEAR
RENAME
Speaker terminal wrench
Power cable
Optimizer microphone
Indoor FM antenna
(U.S.A., Canada, China, Asia, General,
and Korea models)
Indoor FM antenna
(Europe, U.K. and Australia models)
AM loop antenna
About this manual
• y indicates a tip for your operation.
• Some operations can be performed by using either the buttons on the front panel or the ones on the remote control. In case the
button names differ between the front panel and the remote control, the button name on the remote control is given in
parentheses.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements,
etc. In case of differences between the manual and product, the product has priority.
3 En
01EN_00_RX-V1700_U.book Page 4 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
CONTROLS AND FUNCTIONS
Front panel
This section describes only the amplifier controls and functions of this unit. See the following pages for details about
other control and functions.
• AM/FM tuning ........................... see page 54
• XM satellite radio tuning ........... see page 62
1
2
3
4
5
6
7
8
9
0 A
B
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
SILENT CINEMA
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
S VIDEO
PHONES
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
VIDEO AUX
ON
OFF
MASTER
C
D
E
1 MASTER ON/OFF
Turns this unit on or off (see page 31).
2 MAIN ZONE ON/OFF
Turns on the main zone or sets it to the standby mode
(see page 31).
Notes
• In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control.
• When you turn on this unit, there will be a 4 to 5-second delay
before this unit can reproduce sound.
• This button is operational only when MASTER ON/OFF is
pressed inward to the ON position.
3 INPUT selector
Selects the desired input source (see page 38).
4 En
F
G
(U.S.A. model)
4 AUDIO SELECT
Toggles the priority for the type of audio input jack
between “AUTO”, “HDMI”, “COAX/OPT” and
“ANALOG” when one component is connected to two or
more input jacks (see page 40).
5 TONE CONTROL
Adjusts the bass/treble balance of the front left, front right
and center channels in conjunction with the PROGRAM
selector (see page 50).
6 STRAIGHT
Turns the sound field programs off or on. When the
“STRAIGHT” mode is selected, 2-channel or multichannel input signals are output directly from their
respective speakers without effect processing (see
page 49).
01EN_00_RX-V1700_U.book Page 5 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
7 MULTI ZONE buttons
ZONE 3 ON/OFF
Turns on Zone 3 only or sets it to the standby mode.
See page 114 for details.
Note
D OPTIMIZER MIC jack
Use to connect and input audio signals from the supplied
optimizer microphone in the “AUTO SETUP” procedure
(see page 32).
These buttons are operational only when MASTER ON/OFF
is pressed inward to the ON position.
E
PHONES jack
Outputs audio signals for private listening with
headphones (see page 41).
ZONE CONTROLS
Switches the zone you want to control between the
main zone, Zone 2 and Zone 3. See page 114 for
details.
F VIDEO AUX jacks
Input audio and video signals from a portable external
source such as a game console or a video camera
(see page 27).
y
After you press ZONE CONTROLS, the indicator for the
currently selected zone flashes in the front panel display for
approximately 5 seconds. While the indicator is flashing,
perform the desired operation.
8 Front panel display
Shows information about the operational status of this unit
(see page 10).
9 ENHANCER
Turns on or off the Compressed Music Enhancer mode
(see page 52).
y
To reproduce the source signals input at these jacks, select
“V-AUX” as the input source.
Note
The audio signals input at the DOCK terminal on the rear panel
take priority over the ones input at the VIDEO AUX jacks.
G VOLUME
Controls the output level of all audio channels.
y
This does not affect the AUDIO OUT (REC) level.
0 Remote control sensor
Receives signals from the remote control (see page 9).
■ Opening and closing the front panel
door
A NIGHT
Turns on or off the night listening modes (see page 53).
When you want to use the controls behind the front panel
door, open the door by gently pressing on the lower part of
the panel. Keep the door closed when not using these
controls.
B PURE DIRECT
Turns on or off the Pure Direct mode (see page 50).
To open, press gently on the lower part of the panel.
5 En
INTRODUCTION
ZONE 2 ON/OFF
Turns on Zone 2 only or sets it to the standby mode.
See page 114 for details.
C PROGRAM selector
• Selects sound field programs (see page 44).
• Adjusts the bass/treble balance in conjunction with
TONE CONTROL (see page 50).
01EN_00_RX-V1700_U.book Page 6 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
Remote control
■ Remote control controls and functions
This section describes only the amplifier controls and functions of this unit. See the following pages for details about
other control and functions.
• AM/FM tuning ........................................ see page 54
• XM satellite radio tuning ........................ see page 62
• Controlling a TV ................................... see page 101
• Controlling other components ............... see page 102
• Controlling option components ............. see page 103
1
2
Note
B
POWER
POWER
TV
AV
XM
PHONO
3
TUNER
STANDBY
POWER
AUDIO SEL
SLEEP
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
C
D
E
F
V-AUX/DOCK CBL/SAT
DTV
VCR 1
4
SELECT
+
+
SOURCE
TV VOL
CH
VOLUME
–
–
–
TV MUTE
5
TV INPUT
G
SET MENU
TITLE
MENU
BAND
SRCH MODE
6
PURE DIRECT
7
PARAMETER
STRAIGHT
DISPLAY
RETURN
EFFECT
XM MEMORY
8
9
H
The selected input source name appears in the display window on
the remote control showing which source is currently operational.
I
J
4 Display window
Shows the name of the selected input source that you can
control.
K
L
5 LEVEL
Selects the speaker channel to be adjusted and sets the
output level (see page 51).
AUDIO
ENTER
A-E/CAT.
CLASSICAL
LIVE/CLUB
ENTERTAIN
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
7
8
NIGHT
ENHANCER
9
0
+ 10
ENT
M
N
MOVIE
O
P
Q
R
REC
DISC SKIP
0
OFF
ON
MACRO
LEARN
CLEAR
S
t
U
A
(U.S.A. model)
6 En
RENAME
3 Input selector buttons
Select the input source you want to control.
y
TV
MUTE
PRESET/CH
LEVEL
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate (see page 9).
2 TRANSMIT indicator
Flashes while the remote control is sending infrared
signals.
AMP
+
The operation mode of the remote control buttons in the shaded
area below depends on the operation mode selector position. Set
the operation mode selector to AMP to control this unit.
6 Cursor buttons k / n / l / h, ENTER
Select and adjust the sound field program parameters or
the “SET MENU” parameters.
7 RETURN
Returns to the previous menu level when adjusting the
“SET MENU” parameters.
8 Sound field program selector buttons
Select sound field programs (see page 44).
9 SUR. DECODE
Activates decoders to play back 2-channel sources in
surround (see page 80).
01EN_00_RX-V1700_U.book Page 7 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
I VOLUME +/–
Increases or decreases the volume level.
A MACRO
Programs a series of operations to be controlled with a
single button (see page 107).
J MUTE
Mutes the audio output. Press again to restore the audio
output to the previous volume level (see page 41).
B STANDBY
Sets the main zone to the standby mode (see page 31).
K PURE DIRECT
Turns on or off the pure direct mode (see page 50).
Note
L SET MENU
Enters “SET MENU” (see page 86).
This button is operational only when MASTER ON/OFF on the
front panel is pressed inward to the ON position.
C POWER
Turns on the main zone (see page 31).
Note
This button is operational only when MASTER ON/OFF on the
front panel is pressed inward to the ON position.
D AUDIO SEL
Toggles the priority for the type of audio input jack
between “AUTO”, “HDMI”, “COAX/OPT” and
“ANALOG” when one component is connected to two or
more input jacks (see page 40).
E SLEEP
Sets the sleep timer (see page 43).
F MULTI CH IN
Selects the component connected to the MULTI CH
INPUT jacks as the input source when using an external
decoder, etc. (see page 41).
G SELECT k / n
Selects another input source that you can control
independently of the input source selected with the input
selector buttons.
H Operation mode selector
Selects the operation mode of the remote control buttons
in the shaded area.
AMP
Operates the amplifier function of this unit.
SOURCE
Operates the component selected with an input
selector button (see page 102).
M PARAMETER
Displays sound field parameter settings in the on-screen
display (OSD) (see page 76).
N STRAIGHT
Turns the sound field programs off or on. When the
“STRAIGHT” mode is selected, 2-channel or multichannel input signals are output directly from their
respective speakers without effect processing (see
page 49).
O EXTD SUR.
Switches between 5.1 and 6.1/7.1-channel playback of
multi-channel sources (see page 80).
P SELECT
Selects decoders for 2-channel sources (see pages 80 and
82).
Q ENHANCER
Turns on or off the Compressed Music Enhancer mode
(see page 52).
R NIGHT
Turns on or off the night listening modes (see page 53).
S RENAME
Changes the name of the input source in the display
window (see page 106).
T CLEAR
Clears remote control functions acquired from the learn,
macro and/or rename features (see page 110).
U LEARN
Programs remote control codes of functions from other
remote controls (see page 105).
TV
Operates the TV assigned to either DTV/CBL or
PHONO (see page 101).
Notes
• To set the remote control codes for other components, see
page 103.
• When you set the remote control codes for both DTV/CBL and
PHONO (see page 103), priority is given to the one set for
DTV/CBL.
7 En
INTRODUCTION
0 MACRO ON/OFF
Turns on or off the macro function (see page 107).
01EN_00_RX-V1700_U.book Page 8 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
Zone 2/Zone 3 remote control
This section describes the function of each control on the
Zone 2/Zone 3 remote control used to control the amplifier
functions of Zone 2 or Zone 3.
See the following pages for details about other controls
and functions.
1 Input selector buttons
Select the desired input source of Zone 2 or Zone 3.
• AM/FM tuning ........................................ see page 54
• XM Satellite Radio tuning ...................... see page 62
3 POWER
Turns on Zone 2 or Zone 3.
Note
Note
Zone 2/Zone 3 remote control is supplied with U.S.A., Canada,
Australia, U.K., China, Asia and General models only.
This button is operational only when MASTER ON/OFF on the
front panel is pressed inward to the ON position.
4 STANDBY
Sets Zone 2 or Zone 3 to the standby mode.
POWER
XM
3
TUNER
CD
CD-R
1
2
3
DTV
1
5
VCR 1 DVR/VCR 2
7
4
6
ENT
DVD
V-AUX/DOCK
9
0
8
A/B/C/D/E
6
MUTE
A-E/CAT.
DISPLAY
PRESET/CH
ALL
PRESET
ID1 ID2
2
CAT.
ZONE 2 ZONE 3
NUMBER
(U.S.A. model)
8 En
This button is operational only when MASTER ON/OFF on the
front panel is pressed inward to the ON position.
5 VOLUME +/–
Increases or decreases the volume level of Zone 2 or
Zone 3.
5
VOLUME
PRESET
Note
STANDBY
CBL/SAT MD/TAPE PHONO
4
2 ID1/ID2 switch
Switches the remote control ID between ID1 and ID2
(see page 104).
7
6 MUTE
Mutes the sound of Zone 2 or Zone 3. Press again to
restore the audio output to the previous volume level.
7 ZONE 2/ZONE 3 switch
Switches between the operation mode of Zone 2 and that
of Zone 3.
01EN_00_RX-V1700_U.book Page 9 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
Preparing the remote control
2
1
3
1
Press the
part and slide the battery
compartment cover off.
2
Insert the four supplied batteries
(AAA, R03, UM-4) according to the polarity
markings (+ and –) on the inside of the
battery compartment.
3
Slide the cover back until it snaps into place.
■ Installing batteries in the Zone 2/Zone 3
remote control (Except Europe model)
Notes
• Change all of the batteries if you notice the following
conditions:
– the operation range of the remote control decreases.
– the TRANSMIT indicator does not flash or its light becomes
dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
• If the remote control is without batteries for more than 2
minutes, or if exhausted batteries remain in the remote control,
the contents of the memory may be cleared. When the memory
is cleared, insert new batteries, set up the remote control code
and program any acquired functions that may have been
cleared.
■ Using the remote control
The remote control transmits a directional infrared ray.
Be sure to aim the remote control directly at the remote
control sensor on this unit during operation.
Remote control sensor
1
3
2
Approximately 6 m (20 ft)
1
Take off the battery compartment cover.
2
Insert the two supplied batteries (AAA, R03,
UM-4) according to the polarity markings
(+ and –) on the inside of the battery
compartment.
3
Snap the battery compartment cover back
into place.
30
30
Notes
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types
of conditions:
– places of high humidity, such as near a bath
– places of high temperatures, such as near a heater or stove
– places of extremely low temperatures
– dusty places
9 En
INTRODUCTION
■ Installing batteries in the remote control
01EN_00_RX-V1700_U.book Page 10 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
Front panel display
Note
The XM indicator is only applicable to the U.S.A. and Canada models and the cursor on the left of the XM indicator lights up only when
“XM” is selected as the input source. For details, see “Basic XM Satellite Radio operations” on page 65.
1
2
3
V-AUX
DOCK
4
DVR/VCR 2
VCR 1 CBL/SAT
DTV
DVD
MD/TAPE
5
CD-R
CD
PHONO
6
MULTI CH
TUNER XM
neural
VIRTUAL HiFi DSP
YPAO ENHANCER SILENT
DSD
PCM
0
A
B
C
D
E
F
DIGITAL
PL x
EX
dB
VOLUME MUTE
96/24
L C R
LFE SL SB SR
CINEMA
MATRIX DISCRETE
96
24
7
neural
DSD
PCM
VIRTUAL HiFi DSP
YPAO ENHANCER SILENT
CINEMA
DIGITAL
PL x
EX MATRIX
DISCRETE
G
96
24
8
H
I
9
L
M
N
O
P
J
K
TUNED STEREO
AUTO MEMORY
PS
ZONE2 PTY
ZONE3 RT
NIGHT CT
SLEEP EON
PTY HOLD
TUNED STEREO
AUTO MEMORY
PS
ZONE2 PTY
ZONE3 RT
NIGHT CT
SLEEP EON
PTY HOLD
0 ........ U.S.A. and Canada models only
P ........ U.K. and Europe models only
1 HDMI indicator
Lights up when the signal of the selected input source is
input at HDMI IN 1 or HDMI IN 2 jacks (see page 19).
8 96/24 indicator
Lights up when a DTS 96/24 signal is input to this unit.
9 Input channel and speaker indicators
2 DOCK indicator
Lights up when you station your iPod in a YAMAHA iPod
universal dock (such as the YDS-10, sold separately)
connected to the DOCK terminal of this unit
(see page 27).
Presence speaker indicators
L C R
LFE SL SB SR
Presence and surround back speaker
indicators
Light up according to the number of presence and
surround back speakers set for “PRESENCE SP” (see
page 89) and “SB L/R SP” (see page 89) in “SOUND
MENU” when “TEST” in “SOUND MENU” is set to
“ON” (see page 92).
4 Input source indicators
The corresponding cursor lights up to show the currently
selected input source.
5 VOLUME level indicator
Indicates the current volume level.
7 Multi-information display
Shows the name of the current sound field program and
other information when adjusting or changing settings.
10 En
Surround back speaker indicators
Input channel indicators
Indicate the channel components of the current digital
input signal.
3 Battery charge indicator
Lights up when this unit charges the battery of the
stationed iPod in the standby mode of this unit. (see
page 73).
6 MUTE indicator
Flashes while the MUTE function is on (see page 41).
Input channel indicators
y
You can make settings for the presence and surround back
speakers automatically by running “AUTO SETUP” (see
page 32) or manually by adjusting settings for “PRESENCE SP”
(see page 89) and “SB L/R SP” (see page 89) in “SOUND
MENU”.
01EN_00_RX-V1700_U.book Page 11 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
A DSP indicators
The respective indicator lights up when any of the DSP
sound field programs are selected.
CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound
field program (see page 45).
HiFi DSP indicator
Lights up when you select a HiFi DSP sound field
program (see page 45).
B VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 49).
C YPAO indicator
Lights up when you run “AUTO SETUP” and when the
speaker settings set in “AUTO SETUP” are used without
any modifications (see page 32).
D DSD indicator
Lights up when this unit is producing DSD (Direct Stream
Digital) digital audio signals.
E ENHANCER indicator
Lights up when the Compressed Music Enhancer mode is
turned on (see page 52).
F PCM indicator
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) digital audio signals.
G Dolby decoder indicators
The respective indicator lights up when any of the Dolby
decoders of this unit function.
H Sound field indicators
Light up to indicate the active DSP sound fields.
Presence DSP sound field
Listening position
Surround left
DSP sound field
Surround right
DSP sound field
Surround back DSP sound field
I Headphones indicator
Lights up when headphones are connected (see page 41).
J SILENT CINEMA indicator
Lights up when headphones are connected and a sound
field program is selected (see page 49).
K DTS decoder indicators
The respective indicator lights up when any of the DTS
decoders of this unit function.
L Tuner indicators
Lights up when this unit is in the FM, AM or XM Satellite
Radio tuning mode.
TUNED indicator
Lights up when this unit is tuned into a station
(see page 54).
STEREO indicator
Lights up when this unit is receiving a strong signal
for an FM stereo broadcast while the AUTO indicator
is lit (see page 54).
AUTO indicator
Lights up when this unit is in the automatic tuning
mode (see page 54).
MEMORY indicator
Flashes to show that a station can be stored
(see page 57).
M ZONE2/ZONE3 indicators
Lights up when Zone 2 or Zone 3 is turned on
(see page 114).
N NIGHT indicator
Lights up when you select a night listening mode
(see page 53).
O SLEEP indicator
Lights up while the sleep timer is on (see page 43).
P Radio Data System indicators
(U.K. and Europe models only)
PS, PTY, RT and CT
Light up according to the selected Radio Data System
display mode.
EON
Lights up when the EON data service is being
received.
PTY HOLD
Lights up while searching for the Radio Data System
stations in the PTY SEEK mode.
11 En
INTRODUCTION
0 neural indicator
(U.S.A. and Canada models only)
Lights up when the Neural Surround decoder is activated
(see page 81).
01EN_00_RX-V1700_U.book Page 12 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
Rear panel
1
2
MONITOR OUT
3
4
COMPONENT VIDEO
A DVD
B DTV C CBL/SAT
Y
5
VIDEO
DVD
CBL/SAT
DTV
IN
6
7
8
ANTENNA
VCR 1
OUT
IN DVR/VCR 2 OUT
MONITOR OUT
FM
Y
GND
AC IN
AM
S VIDEO
PB
PB
PR
PR
IN
(PLAY)
IN
REMOTE
VIDEO
OUT
(REC)
R
MD/
+
SP1
PRESENCE
+
SURROUND BACK/
BI-AMP
SPEAKERS
+
L
WRENCH
HOLDER
L
TAPE
OUT
R
HDMI
GND
PHONO
IN 2
L
CBL/
SAT
R
CD
CD-R
CENTER
FRONT(6CH) SURROUND
CENTER
FRONT
SURROUND SINGLE(SB)
ZONE 2
ZONE 3
SINGLE
CENTER
+
+
AC OUTLETS
R
IN(PLAY)
IN 1
OUT(REC)
AUDIO
XM
DOCK
SUB
WOOFER
SURROUND
+
L
R
PRESENCE
WOOFER
MULTI CH INPUT
DIGITAL INPUT
+
SUR.BACK/
SUB
SB(8CH)
SP2
L
ZONE OUT
DIGITAL OUTPUT
PRE OUT
+
DVD
OPTICAL
COAXIAL
OUT
1 CD
2 DVD
DVR/
3 VCR2
4 CD
5 DVD
6 DTV
7 CBL/
SAT
8 MD/
TAPE
R
+
+
FRONT
L
9 CD-R
2
1
CONTROL OUT
RS-232C
(U.S.A. model)
9
0
A
B
C
D
CENTER
SUB
WOOFER
FRONT(6CH) SURROUND
SB(8CH)
MULTI CH INPUT
F
E
CENTER
FRONT
SURROUND SINGLE(SB)
ZONE 2
ZONE 3
SUR.BACK/
SUB
PRESENCE
WOOFER
PRE OUT
ZONE OUT
G
H
1 REMOTE jacks
See page 113 for details.
0 DOCK terminal
See page 27 for connection information.
2 COMPONENT VIDEO jacks
See pages 21 and 22 for connection information.
A XM jack (U.S.A. and Canada models only)
See page 61 for connection information.
3 Audio component jacks
See page 24 for connection information.
B DIGITAL INPUT/OUTPUT jacks
See page 22 for connection information.
4 Video component jacks
See pages 21 and 22 for connection information.
C CONTROL OUT jack
This is a control expansion terminal for custom
installation.
5 ANTENNA terminals
See page 28 for connection information.
6 WRENCH HOLDER
Use to hook the supplied speaker terminal wrench when
not in use (see page 15).
7 VOLTAGE SELECTOR
(Asia and General models only)
See page 29 for details.
D RS-232C terminal
This is a control expansion terminal for factory use only.
Consult your dealer for details.
E Speaker terminals
See page 14 for connection information.
F MULTI CH INPUT jacks
See page 26 for connection information.
8 AC IN/OUTLET(S)
See page 29 for connection information.
G PRE OUT jacks
See page 25 for connection information.
9 HDMI connectors
See page 19 for connection information.
H ZONE OUT jacks
See page 113 for connection information.
12 En
01EN_00_RX-V1700_U.book Page 13 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
CONNECTIONS
Placing speakers
The speaker layout below shows the speaker setting we
recommend. You can use it to enjoy CINEMA DSP and
multi-channel audio sources.
PL
PR
C
Center speaker (C)
The center speaker is for the center channel sounds
(dialog, vocals, etc.). If for some reason it is not practical
to use a center speaker, you can do without it. Best results,
however, are obtained with the full system. Place the
center speaker centrally between the front speakers and as
close to the monitor as possible, such as directly over or
under it.
30˚
SL
SR
60˚
80˚
SL
SR
SBL
Surround left and right speakers (SL and SR)
The surround speakers are used for effect and surround
sounds. Place these speakers behind your listening
position, facing slightly inwards, about 1.8 m (6 ft) above
the floor.
SBR
30 cm (12 in) or more
Surround back left and right speakers
(SBL and SBR)
The surround back speakers supplement the surround
speakers and provide more realistic front-to-back
transitions. Place these speakers directly behind the
listening position and at the same height as the surround
speakers. They should be positioned at least 30 cm (12 in)
apart. Ideally, they should be positioned at the same width
as that of the front speakers.
PR
FR
PL
SW
FL
SR
SBR
C
SBL
SL
1.8 m (6 ft)
0.5 to 1 m (1 to 3 ft)
0.5 to 1 m (1 to 3 ft)
PL
PR
FR
FL
C
1.8 m (6 ft)
Presence left and right speakers (PL and PR)
The presence speakers supplement the sound from the front
speakers with extra ambient effects produced by CINEMA
DSP (see page 134). These effects include sounds that
filmmakers intend to locate a little farther back behind the
screen in order to create more theater-like ambience. Place
these speakers at the front of the room about 0.5 to 1 m (1
to 3 ft) outside the front speakers, facing slightly inward,
and about 1.8 m (6 ft) above the floor.
Subwoofer (SW)
The use of a subwoofer with a built-in amplifier, such as
the YAMAHA Active Servo Processing Subwoofer
System, is effective not only for reinforcing bass
frequencies from any or all channels, but also for high
fidelity sound reproduction of the LFE (low-frequency
effect) channel included in Dolby Digital and DTS
sources. The position of the subwoofer is not so critical,
because low bass sounds are not highly directional. But it
is better to place the subwoofer near the front speakers.
Turn it slightly toward the center of the room to reduce
wall reflections.
13 En
PREPARATION
FR
FL
Front left and right speakers (FL and FR)
The front speakers are used for the main source sound plus
effect sounds. Place these speakers at an equal distance from
the ideal listening position. The distance of each speaker
from each side of the video monitor should be the same.
01EN_00_RX-V1700_U.book Page 14 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Connecting speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,
no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be
unnatural and lack bass.
CAUTION
• Before connecting the speakers, make sure that this unit is turned off (see page 31).
• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this
unit. This could damage this unit and/or speakers.
• Use magnetically shielded speakers. If this type of speaker still creates interference with the
monitor, place the speakers away from the monitor.
• If you are to use 6 ohm speakers, be sure to set “SP IMP.” to “6ΩMIN” before using this unit (see
page 30). 4 ohm speakers can be also used as the front speakers (see page 118).
Notes
• A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a
stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the
plain cable to the “–” (black) terminals.
• The low-frequency signals of other speakers set to “SML” (or “SMALL”) or to “NONE” in “SPEAKER SET” (see pages 87 and 89)
are directed to the speakers selected in “LFE/BASS OUT” (see page 87).
• You can connect both surround back and presence speakers to this unit, however they do not output sound simultaneously. You can set
to prioritize either set of speakers using the “PRIORITY” parameter in “MANUAL SETUP” (see page 89).
• You can use the PRESENCE terminals to connect the Zone 2 or Zone 3 speakers as well as the presence speakers (see page 113).
Subwoofer
Surround back speakers
Left
Right
Presence speakers
Left
Right
Center speaker
R
R
+
SP1
PRESENCE
+
SURROUND BACK/
BI-AMP
+
SPEAKERS
+
SINGLE
SURROUND
L
CENTER
+
+
+
L
SUB
R
WOOFER
SP2
L
PRE OUT
R
+
FRONT
+
L
(U.S.A. model)
Zone 2 or Zone 3
speakers
(see page 113)
Left
Right
Surround speakers
Left
Right
Front speakers
14 En
01EN_00_RX-V1700_U.book Page 15 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
FRONT terminals
Connect front left and right speakers to these terminals.
■ Connecting the speaker cable
CENTER terminals
Connect a center speaker to these terminals.
1
SURROUND terminals
Connect surround left and right speakers to these
terminals.
SURROUND BACK terminals
Connect surround back left and right speakers to these
terminals.
Remove approximately 10 mm (0.4 in) of
insulation from the end of each speaker
cable and then twist the exposed wires of the
cable together to prevent short circuits.
10 mm (0.4 in)
When you use a surround back speaker, connect the speaker to the
left SURROUND BACK terminal (SINGLE).
2
PRESENCE terminals
Connect presence left and right speakers to these
terminals.
Loosen the knob using the supplied speaker
terminal wrench.
Speaker terminal wrench
SUBWOOFER jack
Connect a subwoofer with a built-in amplifier (such as the
YAMAHA Active Servo Processing Subwoofer System)
to this jack.
Red: positive (+)
Black: negative (–)
3
Insert one bare wire into the hole on the side
of each terminal.
4
Tighten the knob to secure the wire using the
supplied speaker terminal wrench.
15 En
PREPARATION
Note
01EN_00_RX-V1700_U.book Page 16 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
5
Hook the speaker terminal wrench onto the
WRENCH HOLDER on the rear panel of this
unit when not in use.
■ Connecting the banana plug
(except U.K., Europe, Asia and Korea
models)
The banana plug is a single-pole electrical connector
widely used to terminate speaker cables.
Banana plug
■ Connecting to the SP2 speaker
terminals
1
Connect Zone 2 or Zone 3 speakers to these terminals (see
page 113).
1
Tighten the knob using the supplied speaker
terminal wrench.
Speaker terminal wrench
Open the tab.
Red: positive (+)
Black: negative (–)
Red: positive (+)
Black: negative (–)
2
2
Insert the banana plug connector into the
end of the corresponding terminal.
Insert one bare wire into the hole on the
terminal.
y
3
Close the tab to secure the wire.
16 En
You can also use the banana plug with the SP2 speaker terminals.
Open the tab and then insert one banana plug into the hole on the
terminal. Do not close the tab after connecting the banana plug.
01EN_00_RX-V1700_U.book Page 17 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Using bi-amplification connections
■ Bi-amplification connection
To make the bi-amplification connections, use the FRONT
and SURROUND BACK terminals as shown below. To
activate the bi-amplification connections, set “BI-AMP”
to “ON” in “ADVANCED SETUP” (see page 119).
This unit
+
SURROUND BACK/
BI-AMP
+
FRONT
SINGLE
PREPARATION
Some of the speakers have speaker wire connections that
allow bi-amplification to enhance the performance of the
speaker system. This unit allows you to make biamplification connection to one speaker system. Check if
your speakers support bi-amplification. As these speakers
are shipped to you, you will note shorting bars or bridges,
one connecting the two red input terminals and the other
connecting the two black input terminals. Remove these
shorting bars or bridges only if you plan to bi-amplify
your speakers.
+
■ Conventional connection
If you want to connect your speakers as traditional
loudspeakers using the conventional connection method,
connect your speakers using the regular left and right
speaker wire connections and ignore the second set of
terminals.
R
+
L
This unit
R
+
+
FRONT
L
Right
Left
Front speakers
Note
Remove the shorting bars or bridges to separate the LPF (low
pass filter) and HPF (high pass filter) crossovers.
Right
Left
Front speakers
Shorting bars
or bridges
Shorting bars
or bridges
17 En
01EN_00_RX-V1700_U.book Page 18 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Information on jacks and cable plugs
Audio jacks and cable plugs
DIGITAL
DIGITAL
L
R
COAXIAL
OPTICAL
(White)
(Red)
(Orange)
L
R
C
AUDIO
Left and right
Coaxial
analog audio digital audio
cable plugs
cable plug
Video jacks and cable plugs
VIDEO
S VIDEO
(Yellow)
O
V
S
Optical
digital
audio cable
plug
Composite
video cable
plug
S-video
cable plug
COMPONENT VIDEO
Y
PB
PR
(Green)
(Blue)
(Red)
Y
PB
PR
Component
video cable
plugs
■ Audio jacks
■ Video jacks
This unit has three types of audio jacks. Connection
depends on the availability of audio jacks on your other
components.
This unit has three types of video jacks. Connection
depends on the availability of input jacks on your video
monitor.
AUDIO jacks
For conventional analog audio signals transmitted via left
and right analog audio cables. Connect red plugs to the
right jacks and white plugs to the left jacks.
VIDEO jacks
For conventional composite video signals transmitted via
composite video cables.
DIGITAL COAXIAL jacks
For digital audio signals transmitted via coaxial digital
audio cables.
DIGITAL OPTICAL jacks
For digital audio signals transmitted via optical digital
audio cables.
Note
You can use the digital jacks to input PCM, Dolby Digital and
DTS bitstreams. When you connect components to both the
COAXIAL and OPTICAL jacks, priority is given to the signals
input at the COAXIAL jack. All digital input jacks are
compatible with 96-kHz sampling digital signals.
18 En
S VIDEO jacks
For S-video signals, separated into the luminance (Y) and
chrominance (C) video signals transmitted on separate
wires of S-video cables.
COMPONENT VIDEO jacks
For component video signals, separated into the
luminance (Y) and chrominance (PB, PR) video signals
transmitted on separate wires of component video cables.
y
This unit equips the video connection function. See pages 20 and
97 for details.
01EN_00_RX-V1700_U.book Page 19 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Information on HDMI
This unit has the HDMI IN 1, HDMI IN 2 and HDMI OUT jacks for digital audio and video signal input/output. Connect
the HDMI IN 1 or HDMI IN 2 jack of this unit to the HDMI output jack of other HDMI components (such as a DVD
player). Connect the HDMI OUT jack of this unit to the HDMI IN jack of other HDMI components (such as a TV and a
projector).
The video or audio signals input at the HDMI IN 1 or HDMI IN 2 jack of the selected input source are output at the
HDMI OUT jack of this unit.
Note
You can check the potential problem about the HDMI connection (see page 42).
Audio signal
types
Audio signal
formats
Compatible
HDMI
components
2ch Linear
PCM
2ch, 32-192 kHz,
16/20/24 bit
CD, DVD-Video,
DVD-Audio, etc.
Multi-ch
Linear PCM
8ch, 32-192 kHz,
16/20/24 bit
DVD-Audio, etc.
DSD
2/5.1ch,
2.8224 MHz,1 bit
SACD, etc.
Bitstream
Dolby Digital,
DTS
DVD-Video, etc.
PREPARATION
■ HDMI compatibility with this unit
■ HDMI jack and cable plug
HDMI
HDMI cable plug
This unit’s HDMI interface is based on the following
standards:
• HDMI Version 1.2a (High-Definition Multimedia
Interface Specification Version 1.2a) licensed by
HDMI Licensing, LLC.
• HDCP Revision 1.1 (High-bandwidth Digital
Content Protection System Revision 1.1) licensed
by Digital Content Protection, LLC.
Notes
• When CPPM copy-protected DVD audio is played back, video
and audio signals may not be output depending on the type of
the DVD player.
• This unit is not compatible with HDCP-incompatible HDMI or
DVI components.
y
• We recommend using an HDMI cable shorter than 5 meters (16
feet) with the HDMI logo printed on it.
• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect
this unit to other DVI components.
Notes
• Do not disconnect or connect the cable or turn off the power of
the HDMI components connected to the HDMI OUT jack of
this unit while data is being transferred. Doing so may disrupt
playback or cause noise.
• Audio signals input at input jacks other than the HDMI IN 1 or
HDMI IN 2 of this unit cannot be digitally output at the
HDMI OUT jack.
• If you turn off the power of the video monitor connected to the
HDMI OUT jack via a DVI connection, this unit may fail to
establish the connection to the component.
• The analog video signals input at the composite video, S-video
and component video jacks can be digitally up-converted to be
output at the HDMI OUT jack. Set “V CONV.” to “ON” in
“MANUAL SETUP” (see page 98) to activate this feature.
19 En
01EN_00_RX-V1700_U.book Page 20 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Audio and video signal flow
■ Audio signal flow
Input
■ Video signal flow
Input
Output
Output
HDMI
HDMI
DIGITAL AUDIO
(COAXIAL)
COMPONENT
VIDEO
DIGITAL AUDIO
(OPTICAL)
S VIDEO
AUDIO
VIDEO
Digital output
Through
Analog output
Video conversion (see page 97)
Notes
• 2-channel as well as multi-channel PCM, Dolby Digital and
DTS signals input at the HDMI IN 1 or HDMI IN 2 jack can be
output at the HDMI OUT jack only when “SUPPORT AUDIO”
is set to “OTHER” (see page 93).
• Audio signals input at the HDMI IN jacks are not output at the
analog AUDIO OUT and DIGITAL OUTPUT jacks.
Component interlace/progressive
up-conversion (see page 98)
HDMI interlace/progressive
up-conversion (see page 98)
Notes
• When the analog video signals are input at the COMPONENT
VIDEO, S VIDEO and VIDEO jacks, the priority order of the
input signals is as follows:
1. COMPONENT VIDEO
2. S VIDEO
3. VIDEO
• The analog video signals output at the COMPONENT VIDEO
jacks can be deinterlaced from 480i (NTSC)/576i (PAL) to
480p/576p. Set CMPNT I/P to ON in MANUAL SETUP to
activate this feature (see page 98).
• Digital video signals input at the HDMI IN 1 or HDMI IN 2
jack cannot be output from analog video output jacks.
• The analog component video signals with 480i (NTSC)/576i
(PAL) of resolution are converted to the s-video or composite
video signals and output at the S VIDEO MONITOR OUT and
VIDEO MONITOR OUT jacks.
• Component interlace/progressive conversion (see page 98) and
HDMI interlace/progressive up-conversion (see page 98) are
available only when “V CONV.” is set to “ON” (see page 97).
• Use the “HDMI I/P” parameter in “OPTION MENU” to
deinterlace the analog video signals output at the HDMI OUT
jack (see page 98). When the analog video signals with 1080i or
720p of resolution are up-converted to HDMI and output at the
HDMI OUT jack, the picture quality may worsen.
• The OSD signal is not output at the VCR 1 OUT and
DVR/VCR 2 OUT jacks and is not recorded.
• The color of the letters and images in the OSD may differ
depending on the input signals and your video monitor.
20 En
01EN_00_RX-V1700_U.book Page 21 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Connecting a TV monitor or projector
Connect your TV (or projector) to the HDMI OUT jack, the COMPONENT VIDEO MONITOR OUT jacks, the S
VIDEO MONITOR OUT jack or the VIDEO MONITOR OUT jack of this unit.
CAUTION
Do not connect this unit or other components to the AC power supply until all connections between
components are complete.
y
Notes
• Some video monitors connected to this unit via a DVI connection fail to recognize the HDMI audio/video signals being input if they
are in the standby mode. In this case, the HDMI indicator flashes irregularly.
• Set “V CONV.” in “OPTION MENU” to “ON” (see page 97) to display the short message display and parameter displays.
• Set “GRAY BACK” in “OPTION MENU” to “ON” (see page 97) to display the parameter displays.
• The SET MENU and parameter displays appear with the gray background depending on the input video signal format and the setting
of the parameters in “DISPLAY SET” (see page 97).
COMPONENT VIDEO
MONITOR OUT
MONITOR OUT
Y
S VIDEO
PB
VIDEO
PR
HDMI
OUT
(U.S.A. model)
Y
PB
V
PR
Component video in
S
Video in
S-video in
HDMI in
TV
(or projector)
indicates recommended connections
indicates alternative connections
21 En
PREPARATION
You can select to play back HDMI audio signals on this unit or on another HDMI component connected to the HDMI OUT jack on the
rear panel of this unit. Use the “SUPPORT AUDIO” parameter in “SOUND MENU” to select the component to play back HDMI audio
signals (see page 93).
01EN_00_RX-V1700_U.book Page 22 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Connecting other components
CAUTION
Do not connect this unit or other components to the AC power supply until all connections between
components are complete.
Notes
• When “V CONV.” is set to “OFF” (see page 97), be sure to make the same type of video connections as those made for your TV (see
page 21). For example, if you connected your TV to the VIDEO MONITOR OUT jack of this unit, connect your other components to
the VIDEO jacks.
• When “V CONV.” is set to “ON” (see page 97), the converted video signals are output only at the MONITOR OUT jacks. When
recording a source, you must make the same type of video connections between each component.
• To make a digital connection to a component other than the default component assigned to each DIGITAL INPUT or DIGITAL
OUTPUT jack, select the corresponding setting for “OPTICAL OUT”, “OPTICAL IN”, or “COAXIAL IN” in “I/O ASSIGNMENT”
(see page 94).
• If you connect your DVD player to both the DIGITAL INPUT (OPTICAL) and the DIGITAL INPUT (COAXIAL) jacks, priority is
given to the signals input at the DIGITAL INPUT (COAXIAL) jack.
• The parameter displays do not appear when the component video signals with 720p, 1080i or 1080p are input.
• The parameter and short message displays do not appear when the component video signals with 480p/576p, 720p, 1080i or 1080p
resolutions are input and output at the VIDEO or S VIDEO MONITOR OUT jack.
■ Connecting a DVD player
DVD player
Optical out
HDMI out
Coaxial out
Audio out
Component out
S-video out
C
PR
PB
Y
Video out
S
COMPONENT VIDEO
A DVD
R
V
VIDEO
DVD
Y
PB
PR
L
R
HDMI
IN 1
DIGITAL INPUT
DVD
OPTICAL
COAXIAL
2 DVD
5 DVD
(U.S.A. model)
indicates recommended connections
indicates alternative connections
22 En
L
O
01EN_00_RX-V1700_U.book Page 23 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
■ Connecting a DVD recorder, PVR or VCR
Note
*1
When you connect another VCR to this unit, connect it to the VCR 1 terminals (S VIDEO IN, VIDEO IN, AUDIO IN, S VIDEO
OUT, VIDEO OUT and AUDIO OUT jacks) same as DVR/VCR 2 terminals except the DIGITAL INPUT (COAXIAL) jack.
*1
VIDEO
VCR 1
IN
OUT
IN DVR/VCR 2 OUT
S VIDEO
VIDEO
L
R
PREPARATION
R
IN DVR/VCR 2 OUT
DIGITAL INPUT
COAXIAL
R
DVR/
3 VCR2
L
V
S
S-video in
R
Video in
R
Audio in
L
Audio out
V
Video out
S
S-video out
C
Coaxial out
(U.S.A. model)
DVD recorder, PVR or VCR
■ Connecting set-top boxes
Satellite receiver,
cable TV receiver
HDTV decoder
HDMI out
Component out
Optical out
COMPONENT VIDEO
B DTV C CBL/SAT
S
S
V
L
R
Audio out
V
Video out
L
S-video out
R
S-video out
O
Video out
Y
Audio out
PB
Optical out
Component out
PR
O
PR
PB
Y
VIDEO
DTV
CBL/SAT
Y
S VIDEO
PB
VIDEO
PR
L
R
HDMI
IN 2
CBL/
SAT
DIGITAL INPUT
OPTICAL
6 DTV
7 CBL/
SAT
(U.S.A. model)
23 En
01EN_00_RX-V1700_U.book Page 24 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
■ Connecting audio components
Notes
• To make a digital connection to a component other than the default component assigned to each the DIGITAL INPUT jack or the
DIGITAL OUTPUT jack, select the corresponding setting for “OPTICAL OUT”, “OPTICAL IN”, or “COAXIAL IN” in “I/O
ASSIGNMENT” (see page 94).
• Connect your turntable to the GND terminal of this unit to reduce noise in the signal. However, you may hear less noise without the
connection to the GND terminal for some turntables.
• The PHONO jacks are only compatible with a turntable with an MM or a high-output MC cartridge. To connect a turntable with a lowoutput MC cartridge to the PHONO jacks, use an in-line boosting transformer or an MC-head amplifier.
• When you connect both the DIGITAL INPUT (OPTICAL) jack and the DIGITAL INPUT (COAXIAL) jack to an audio component,
the priority is given to the DIGITAL INPUT (COAXIAL) jack.
Audio out
Optical in
L
O
R
Audio in
CD recorder
L
R
IN
(PLAY)
OUT
(REC)
MD/
L
TAPE
R
GND
PHONO
CD
CD-R
L
R
IN(PLAY)
OUT(REC)
AUDIO
DIGITAL OUTPUT
DIGITAL INPUT
OPTICAL
COAXIAL
1 CD
8 MD/
TAPE
4 CD
9 CD-R
(U.S.A. model)
R
Ground
Audio out
L
R
L
O
C
Audio
out
Coaxial
out
R
Optical
out
L
R
Audio
out
O
L
Audio
in
Optical in
Turntable
24 En
CD player
MD recorder or
tape deck
01EN_00_RX-V1700_U.book Page 25 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
■ Connecting an external amplifier
This unit has more than enough power for any home use.
However, if you want to add more power to the speaker
output or if you want to use another amplifier, connect an
external amplifier to the PRE OUT jacks.
Notes
1
2
CENTER
FRONT
3
PREPARATION
• When you make connections to the PRE OUT jacks, do not
make connections to the SPEAKERS terminals.
• The signals output at the FRONT PRE OUT and CENTER PRE
OUT jacks are affected by the TONE CONTROL settings (see
page 50).
• Each PRE OUT jack outputs the same channel signals as the
corresponding SPEAKERS terminals.
• Adjust the volume level of the subwoofer with the control on
the subwoofer (see page 51).
• Some signals may not be output at the SUBWOOFER PRE
OUT jack depending on the settings for “SPEAKER SET” (see
page 87) and “LFE/BASS OUT” (see page 87).
4
SURROUND SINGLE(SB)
L
R
SUR.BACK/
SUB
PRESENCE
WOOFER
PRE OUT
5
1 CENTER PRE OUT jack
Center channel output jack.
2 FRONT PRE OUT jacks
Front channel output jacks.
3 SURROUND PRE OUT jacks
Surround channel output jacks.
4 SURROUND BACK/PRESENCE PRE OUT
jacks
Surround back or presence channel output jacks. When
you only connect one external amplifier for the surround
back channel, connect it to the SINGLE (SB) jack.
y
• Set the “SB L/R SP” to “LRGx2”, “LRGx1”, “SMLx2” or
“SMLx1” and “PRESENCE SP” to “NONE” (see page 89) to
output the surround back channel signals at SURROUND
BACK/PRESENCE PRE OUT jacks.
• Set the “PRESENCE SP” to “YES” and “SB L/R SP” to
“NONE” (see page 89) to output the presence channel signals at
SURROUND BACK/PRESENCE PRE OUT jacks.
5 SUBWOOFER PRE OUT jack
Connect a subwoofer with a built-in amplifier.
25 En
01EN_00_RX-V1700_U.book Page 26 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Connecting a multi-format player or an external decoder
This unit is equipped with 6 additional input jacks (left and right FRONT, CENTER, left and right SURROUND and
SUBWOOFER) for discrete multi-channel input from a multi-format player, external decoder, sound processor or
pre-amplifier.
If you set “INPUT CH” to “8ch” in “MULTI CH SET” (see page 96), you can use the input jacks assigned as “FRONT”
in MULTI CH SET (see page 96) together with the MULTI CH INPUT jacks to input 8-channel signals.
Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to
match the left and right outputs to the left and right input jacks for the front and surround channels.
Notes
• When you select the component connected to the MULTI CH INPUT jacks as the input source (see page 41), this unit automatically
turns off the digital sound field processor, and you cannot select sound field programs.
• This unit does not redirect signals input at the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that
you connect at least a 5.1-channel speaker system before using this feature.
For 6-channel input
For 8-channel input
(
CENTER
FRONT(6CH) SURROUND
)
(
C)
MD/
L
TAPE
L
*1
R
R
CENTER
SUB
WOOFER
FRONT(6CH) SURROUND
SB(8CH)
L
MULTI CH INPUT
L
L
R
R
R
WOOFER
Surround
out
SUB
SB(8CH)
MULTI CH INPUT
R
L
R
L
R
Front out
Center out
Subwoofer
out
Surround out
L
Surround back out
Front out
Center out
Subwoofer
out
SUB
Multi-format player/
External decoder
Multi-format player/
External decoder
Note
*1
26 En
The analog audio input jacks assigned as “FRONT” in
“MULTI CH SET” (see page 96).
01EN_00_RX-V1700_U.book Page 27 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Connecting a YAMAHA iPod
universal dock
Using the VIDEO AUX jacks on the
front panel
This unit is equipped with the DOCK terminal on the rear
panel that allows you to connect a YAMAHA iPod
universal dock (such as the YDS-10, sold separately)
where you can station your iPod and control playback of
your iPod using the supplied remote control. Connect a
YAMAHA iPod universal dock (such as the YDS-10, sold
separately) to the DOCK terminal on the rear panel of this
unit using its dedicated cable.
Do not connect this unit to the AC power supply
until all connections between components are
complete.
CAUTION
Be sure to turn off the volume of this unit and
other components before making connections.
Note
The audio signals input at the DOCK terminal on the rear panel
take priority over the ones input at the VIDEO AUX jacks.
(U.S.A. model)
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
CATEGORY
INPUT
DISPLAY
SEARCH MODE
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
SILENT CINEMA
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
VIDEO AUX
PHONES
ON
OFF
MASTER
S VIDEO
VIDEO
L
S
V
L
AUDIO
R
OPTICAL
R
O
DOCK
YAMAHA iPod universal dock
(such as the YDS-10,
sold separately)
S-Video
output
Video
output
Audio
output
Optical
output
Game console or
video camera
27 En
PREPARATION
CAUTION
Use the VIDEO AUX jacks on the front panel to connect a
game console or a video camera to this unit.
01EN_00_RX-V1700_U.book Page 28 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Connecting the FM and AM antennas
Both FM and AM indoor antennas are supplied with this
unit. Connect each antenna correctly to the designated
terminals. In general, these antennas should provide
sufficient signal strength.
2
Press and hold the tab of the AM ANT
terminal.
3
Insert one of the AM loop antenna lead wires
into the AM ANT terminal.
4
Release the tab of the AM ANT terminal.
5
Repeat steps 2 through 4 to connect the
other lead wire to the GND terminal.
Notes
• Be sure to set the tuner frequency step (Asia and General
models only) according to the frequency spacing in your area
(see page 119).
• The AM loop antenna should be placed away from this unit.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
• A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality,
install an outdoor antenna. Consult the nearest authorized
YAMAHA dealer or service center about outdoor antennas.
Indoor FM
antenna
(supplied)
AM loop
antenna
(supplied)
ANTENNA
FM
GND
AM
(U.S.A. model)
Outdoor AM antenna
Use a 5 to 10 m (16.4 to 32.8
ft) vinyl-covered wire
extended outdoors from a
window.
Ground (GND terminal)
For maximum safety and minimum interference, connect the
antenna GND terminal to a good earth ground. A good earth
ground is a metal stake driven into moist earth.
y
■ Connecting the AM loop antenna
1
Set up the AM loop antenna.
28 En
Once you have properly connected the AM loop antenna to
this unit, orient the AM loop antenna for the best reception
when you tune into AM stations (see page 54).
01EN_00_RX-V1700_U.book Page 29 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Connecting the power cable
■ Connecting the AC power cable
CAUTION
Use the supplied AC cable. Do not use other AC power cables as doing so may result in fire or
electrical shock.
Plug the supplied AC power cable into the AC inlet after all other connections are complete, then plug the AC power
cable into an AC wall outlet.
(U.S.A. model)
PREPARATION
AC IN
To the AC wall outlet
AC OUTLETS
■ VOLTAGE SELECTOR
(Asia and General models only)
CAUTION
The VOLTAGE SELECTOR on the rear panel of
this unit must be set for your local voltage
BEFORE plugging the power cable into the AC
wall outlet. Improper setting of the VOLTAGE
SELECTOR may cause damage to this unit and
create a potential fire hazard.
Rotate the VOLTAGE SELECTOR clockwise or
counterclockwise to the correct position using a
straight slot screwdriver.
Voltages are as follows:
Asia model .........................220/230–240 V AC, 50/60 Hz
General model ......110/120/220/230–240 V AC, 50/60 Hz
VOLTAGE
SELECTOR
230240V
■ AC OUTLET(S) (SWITCHED)
U.K. and Australia models ..................................... 1 outlet
Korea model ............................................................... None
Other models ......................................................... 2 outlets
Use these outlet(s) to supply power to any connected
components. Connect the power cable of your other
components to these outlet(s). Power to these outlet(s) is
supplied when this unit is turned on. However, power to
these outlet(s) is cut off when this unit is turned off. For
information on the maximum power or the total power
consumption of the components that can be connected to
these outlet(s), see “SPECIFICATIONS” on page 136.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby mode.
However, the stored data will be lost in case the power
cable is disconnected from the AC wall outlet or if the
power supply is cut off for more than one week.
Voltage indication
29 En
01EN_00_RX-V1700_U.book Page 30 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Setting the speaker impedance
CAUTION
4
If you are to use 6 ohm speakers, set “SPEAKER
IMP.” to “6ΩMIN” as follows BEFORE using this
unit. 4 ohm speakers can be also used as the
front speakers.
Press STRAIGHT on the front panel
repeatedly to select “6ΩMIN”.
The following display appears in the front panel
display.
STRAIGHT
EFFECT
(U.S.A. model)
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
SPEAKER IMP.
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
PHONES
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
6 MIN
OPTICAL
VIDEO AUX
ON
OFF
MASTER
2,5
1
3
5
2,4
Press MASTER ON/OFF on the front panel to
release it outward to the OFF position to save
the new setting and turn off this unit.
Make sure this unit is turned off.
See page 31 for details about turning on or off this
unit.
MASTER
2
Press and hold STRAIGHT on the front panel
and then press MASTER ON/OFF inward to
the ON position to turn on this unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
STRAIGHT
While holding
down
EFFECT
3
MASTER
Rotate the PROGRAM selector on the front
panel to select “SPEAKER IMP.”.
The following display appears in the front panel
display.
PROGRAM
SPEAKER IMP.
8 MIN
30 En
Note
The setting you made is reflected next time you turn on this
unit.
01EN_00_RX-V1700_U.book Page 31 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
Turning on and off the power
When all connections are complete, turn on this unit.
MAIN ZONE ON/OFF
(U.S.A. model)
(U.S.A. model)
STANDBY
POWER
POWER
TV
AV
PURE DIRECT
XM
STANDBY
POWER
AUDIO SEL
SLEEP
CD
MULTI CH IN
POWER
VOLUME
PHONO
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
TUNER
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
S VIDEO
PHONES
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
VIDEO AUX
ON
PREPARATION
OFF
MASTER
MASTER ON/OFF
■ Turning on this unit
Press MASTER ON/OFF on the front panel
inward to the ON position to turn on this
unit.
When you turns on this unit by pressing MASTER ON/
OFF, the main zone is turned on.
■ Turning on the main zone from the
standby mode
Press MAIN ZONE ON/OFF on the front
panel (or POWER on the remote control) to
turn on the main zone.
MAIN ZONE
POWER
ON/OFF
or
MASTER
Front panel
■ Turning off this unit
Press MASTER ON/OFF on the front panel
again to release it outward to the OFF
position to turn off this unit.
Front panel
Remote control
■ Set the main zone to the standby mode
Press MAIN ZONE ON/OFF on the front
panel (or STANDBY on the remote control)
to set the main zone to the standby mode.
MAIN ZONE
STANDBY
MASTER
ON/OFF
or
Front panel
Notes
Front panel
Remote control
• MAIN ZONE ON/OFF on the front panel as well as POWER
and STANDBY on the remote control are operational only
when MASTER ON/OFF is pressed inward to the ON position.
• As usual, we recommend using the standby mode to turn off this
unit.
31 En
01EN_00_RX-V1700_U.book Page 32 Tuesday, June 27, 2006 9:37 AM
AUTO SETUP
AUTO SETUP
This unit employs the YPAO (YAMAHA Parametric Room Acoustic Optimizer) technology which lets you avoid
troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied
optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening
environment.
Using AUTO SETUP
1
Once you have connected the supplied optimizer
microphone to the OPTIMIZER MIC jack on the front
panel and have placed it in a suitable location in your
listening room, run “AUTO SETUP” in the OSD or in the
front panel display.
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
(U.S.A. model)
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
Notes
DISPLAY
SEARCH MODE
CATEGORY
ZONE ON/OFF
STRAIGHT
ZONE CONTROLS
MULTI ZONE
EFFECT
• Be advised that it is normal for loud test tones to be output
during the “AUTO SETUP” procedure.
• To achieve the best results, make sure the room is as quiet as
possible while the “AUTO SETUP” procedure is in progress. If
there is too much ambient noise, the results may not be
satisfactory.
YPAO
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
PHONES
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
VIDEO AUX
Omni-directional
microphone
y
• You can run “AUTO SETUP” using the system menu that
appears in the OSD or in the front panel display. This manual
uses the OSD illustrations to explain the “AUTO SETUP”
procedure.
• If an error occurs during the “AUTO SETUP” procedure and an
error or warning message appears in the OSD or in the front
panel display, see the “AUTO SETUP” section in
“TROUBLESHOOTING” on pages 128 and 129 for a complete
list of error and warning messages and proper remedies.
• The initial setting for each parameter is indicated in bold.
• If the volume level and the crossover frequency of your
subwoofer can be adjusted, set the volume level to about half
way (or slightly less) and set the crossover frequency to the
maximum.
AMP
+
+
+
TV VOL
CH
VOLUME
–
–
–
SOURCE
TV MUTE
LEVEL
TV INPUT
PRESET/CH
MENU
SRCH MODE
PURE DIRECT
AUDIO
ENTER
A-E/CAT.
PARAMETER
RETURN
XM MEMORY
STRAIGHT
DISPLAY
EFFECT
(U.S.A. model)
32 En
Place the optimizer microphone at your
normal listening position on a flat level
surface with the omni-directional
microphone heading upward.
Optimizer microphone
4
TV
MUTE
SET MENU
TITLE
BAND
2
4,14
3-13
y
It is recommended that you use a tripod (etc.) to affix the
optimizer microphone at the same height as your ears would be
when you are seated in your listening position. You can use a 6
mm diameter screw to fix the optimizer microphone to a tripod
(etc.).
01EN_00_RX-V1700_U.book Page 33 Tuesday, June 27, 2006 9:37 AM
AUTO SETUP
3
SET MENU
SET MENU
.;AUTOSETUP
;MANUALSETUP
.;SIGNALINFO
ENTER
A-E/CAT.
This unit performs the following checks:
Speaker wiring WIRING
Checks which speakers are connected and the
polarity of each speaker.
p
p
Press ENTER to enter “AUTO SETUP”.
The “AUTO:MENU” display appears in the OSD.
PRESET/CH
1 AUTO:MENU
A-E/CAT.
p
p
.SETUP;;;;;;;AUTO
WIRING;;;;;CHECK
DISTANCE;;;CHECK
SIZE;;;;;;;CHECK
EQ;;;;;;;NATURAL
LEVEL;;;;;;CHECK
START
[]/[]:Up/Down
[]/[]:Select
p [
ENTER
Speaker distance DISTANCE
Checks the distance of each speaker from the
listening position and adjusts the timing of each
channel.
Speaker size SIZE
Checks the frequency response of each speaker and
sets the appropriate low-frequency crossover for each
channel.
[ ]/[]:Up/Down
[ENTER]:Enter
6
1 AUTO:MENU
SETUP;;;;;;;AUTO
.WIRING;;;;;CHECK
DISTANCE;;;CHECK
SIZE;;;;;;;CHECK
EQ;;;;;;;NATURAL
LEVEL;;;;;;CHECK
START
[]/[]:Up/Down
[]/[]:Select
p [
MENU
SRCH MODE
TV
5
PRESET/CH
Press l / h to select “SETUP”.
PRESET/CH
ENTER
A-E/CAT.
Choices: AUTO, RELOAD
• Select “AUTO” to automatically run the entire
“AUTO SETUP” procedure.
• Select “RELOAD” to reload the last “AUTO
SETUP” settings and override the previous
settings. When you select “RELOAD”, the
previous auto setup result appears in the OSD. See
step 7 on page 34 and carry out the operations.
Note
“RELOAD” is available only when you have previously run
“AUTO SETUP” and confirmed the results.
Choices: CHECK, SKIP
• Select “CHECK” to automatically check and adjust
the item.
• Select “SKIP” to skip the item and perform no
adjustments.
Parametric equalizer level EQ
Adjusts the frequency and the parametric equalizer
level of each channel to reduce coloration across the
channels and create a cohesive sound field. This is
particularly important if you use different brands or
sizes of speakers for some channels or have a room
with unique sonic characteristics. In addition, the
frequency response of each channel is adjusted in
accordance with the sound output from your front
speakers.
Choices: NATURAL, FLAT, FRONT, SKIP
• Select “NATURAL” to average out the frequency
response of all speakers with higher frequencies
being less emphasized. Recommended if the FLAT
setting sounds a little harsh.
• Select “FLAT” to average the frequency response
of all speakers. Recommended if all of your
speakers are of similar quality.
• Select “FRONT” to adjust the frequency response
of each speaker in accordance with the sound of
your front speakers. Recommended if your front
speakers are of much higher quality than your other
speakers.
• Select “SKIP” to skip the selected item and
perform no adjustments.
33 En
PREPARATION
AMP
SOURCE
Press k / n repeatedly to select “WIRING”,
“DISTANCE”, “SIZE”, “EQ”, or “LEVEL”.
p
Set the operation mode selector to AMP and
then press SET MENU to enter “SET MENU”.
The top “SET MENU” display appears in the OSD.
7
p
4
Make sure of the following check points
before starting the AUTO SETUP operations.
• Speakers are connected appropriately.
• Supplied optimizer microphone is connected to this
unit and placed appropriately.
• Headphones are disconnected from this unit.
• The room is sufficiently quiet.
• The video monitor connected to this unit is turned on.
01EN_00_RX-V1700_U.book Page 34 Tuesday, June 27, 2006 9:37 AM
AUTO SETUP
Volume level LEVEL
Checks and adjusts the volume level of each speaker.
Choices: CHECK, SKIP
• Select “CHECK” to automatically check and adjust
this item.
• Select “SKIP” to skip this item and perform no
adjustments.
8
Press n to select “START” and then press
ENTER to start the setup procedure.
This unit starts the auto setup procedure. Loud test
tones are output from each speaker during the auto
setup procedure. Once all items are set, the
“RESULT:EXIT” display appears in the OSD.
PRESET/CH
PRESET/CH
ENTER
ENTER
A-E/CAT.
A-E/CAT.
Notes
• During the auto setup procedure, do not perform any
operation on this unit.
• We recommend getting out of the room while this unit is in
the auto setup procedure. It takes approximately 3 minutes
for this unit to complete the auto setup procedure.
The display changes as follows.
1 AUTO:MENU
p
p
SETUP;;;;;;;AUTO
WIRING;;;;;CHECK
DISTANCE;;;CHECK
SIZE;;;;;;;CHECK
EQ;;;;;;;NATURAL
LEVEL;;;;;;CHECK
. START
[]/[]:Up/Down
[]/[]:Adjust
p
[
2 AUTO:CHECK
p
INITIALIZING
.PRE CHECK
MAIN CHECK
EQUALIZING
LEVEL
CHECK CH=CENTER
|||||;;;;;;;;
[]: Exit
RESULT:EXIT
34 En
p
p
. RESULT
.
SP :
5/4/0.1
.
DIST: 14.0/ 17.0ft
.
LVL : -9.0/ +6.5dB
[ SET CANCEL
[]/[]:Up/Down
[ENTER]:Enter
The results displayed under “RESULT” are as
follows.
Number of speakers SP
Displays the number of speakers connected to this
unit in the following order:
Front/Back/Subwoofer
Speaker distance DIST
Displays the speaker distance from the listening
position in the following order:
Closest speaker distance/Farthest speaker distance
Speaker level LVL
Displays the speaker output level in the following
order:
Lowest speaker output level/Highest speaker output
level
Notes
• If “E-10:INTERNAL ERROR” appears during the testing
procedure, restart from step 4.
• If you selected “RELOAD” in step 4, no test tones are
output.
• If an error occurs during the “AUTO:CHECK” procedure,
the setup procedure is canceled and an error screen
appears. For details, see “If an error screen appears” on
page 36.
• When this unit detects potential problems during the
“AUTO SETUP” procedure, “WARNING” and the
number of warning messages appears in the above of
“RESULT” (see page 37).
• Depending on the listening environment, “SWFR
PHASE:REV” appears during the “AUTO:CHECK”
procedure and “SUBWOOFER PHASE” in “SOUND
MENU” (see page 89) is automatically set to
“REVERSE”.
01EN_00_RX-V1700_U.book Page 35 Tuesday, June 27, 2006 9:37 AM
AUTO SETUP
9
Press ENTER to display the setup results in
detail.
10
Press l / h repeatedly to toggle between the
setup result displays.
PRESET/CH
PRESET/CH
ENTER
ENTER
A-E/CAT.
A-E/CAT.
RESULT:WIRING
FRONT L;;;;;;;OK
Results of the speaker
connection and wiring
[]/[]:Select
p [
[ENTER]:Return
p
p
. RESULT
.
SP :
5/4/0.1
.
DIST: 14.0/ 17.0ft
.
LVL : -9.0/ +6.5dB
[ SET CANCEL
[]/[]:Up/Down
[ENTER]:Enter
RESULT:DISTANCE1
FRONT L;;14.0ft
CENTER;;;17.0ft
FRONT R;;15.0ft
PRNS L;;;17.0ft
PRNS R;;;17.0ft
RESULT:WIRING
Results of the speaker
distance from the
listening position
[]/[]:Select
p [
[ENTER]:Return
FRONT L;;;;;;;OK
RESULT:SIZE
FRONT L;;;;;;LRG
[]/[]:Select
p [
[ENTER]:Return
Results of the frequency
response of each speaker
[]/[]:Select
p [
[ENTER]:Return
RESULT:EQ
CENTER 1:100Hz;;;+2.5dB
2:300Hz;;;-0.5dB
3:1.5kHz;;+0.5dB
4:1.8kHz;;+2.5dB
5:1.8kHz;;-3.5dB
6:2.5kHz;;+2.5dB
7:10kHz;;;+2.5dB
[]/[]:Select
p [
[ENTER]:Return
RESULT:LEVEL1
FRONT L;;;+1.0dB
CENTER;;;;-1.5dB
FRONT R;;;+6.5dB
PRNS L;;;;-9.0dB
PRNS R;;;;+1.0dB
Results of the parametric
equalizer of each speaker
Results of the speaker
output level
[]/[]:Select
p [
[ENTER]:Return
y
If you are not satisfied with the results or want to manually
adjust each parameter, run “MANUAL SETUP” (see
page 84).
Notes
• If you change speakers, speaker positions, or the layout of
your listening environment, run “AUTO SETUP” again to
recalibrate your system.
• The distances displayed in the “DISTANCE” results may
be longer than the actual distance depending on the
characteristics of your subwoofer.
• In the “EQ” results, different values may be set for the
same band to provide finer adjustments.
35 En
PREPARATION
RESULT:EXIT
01EN_00_RX-V1700_U.book Page 36 Tuesday, June 27, 2006 9:37 AM
AUTO SETUP
11
■ If an error screen appears
Press ENTER to return to the top
“RESULT:EXIT” display.
PRESET/CH
RESULT:EXIT
A-E/CAT.
p
12
p
. RESULT
.
SP :
5/4/0.1
.
DIST: 14.0/ 17.0ft
.
LVL : -9.0/ +6.5dB
[ SET CANCEL
[]/[]:Up/Down
[ENTER]:Enter
ENTER
Make sure the pointer is pointing at “SET”
and “CANCEL” and then press l / h to
select “SET” or “CANCEL”.
PRESET/CH
RESULT:EXIT
A-E/CAT.
p
p
RESULT
.
SP :
5/4/0.1
.
DIST: 14.0/ 17.0ft
.
LVL : -9.0/ +6.5dB
.[
SET CANCEL
[]/[]:Up/Down
[ENTER]:Enter
ENTER
Choices: SET, CANCEL
• Select “SET” to confirm the “AUTO SETUP”
results.
• Select “CANCEL” to cancel the “AUTO SETUP”
results.
13
Press ENTER to confirm your selection.
The top “SET MENU” display appears in the OSD.
PRESET/CH
SET MENU
.;AUTOSETUP
;MANUALSETUP
.;SIGNALINFO
ENTER
14
p
p
[ ]/[]:Up/Down
[ENTER]:Enter
A-E/CAT.
Press SET MENU to exit from “SET MENU”.
SET MENU
MENU
SRCH MODE
Notes
• After you have completed the “AUTO SETUP” procedure, be
sure to disconnect the optimizer microphone.
• The optimizer microphone is sensitive to heat. Keep it away
from direct sunlight and do not place it on top of this unit.
36 En
Press k / n / l / h to select “RETRY” or “EXIT”
and then press ENTER.
The following display is an example where “E-9:USER
CANCEL” appears in the OSD.
ERROR
E-9:USER CANCEL
. Don't operate
any function.
.[
RETRY EXIT
[p]/[[]:Select
[ENTER]:Enter
Choices: RETRY, EXIT
• Select “RETRY” to retry the “AUTO SETUP”
procedure.
• Select “EXIT” to exit from the “AUTO SETUP”
procedure.
01EN_00_RX-V1700_U.book Page 37 Tuesday, June 27, 2006 9:37 AM
AUTO SETUP
■ If “WARNING” appears
When this unit detects potential problems during the
“AUTO SETUP” procedure, “WARNING” appears in the
“RESULT:EXIT” display. Check the warning messages to
correct your speaker settings.
Note
Warnings differ from errors in that warnings do not cancel the
“AUTO SETUP” procedure.
1
PREPARATION
Make sure the pointer is pointing at
“WARNING” and then press ENTER to
display the detailed information about the
warning.
The number on the right of “WARNING” indicates
the number of warning messages.
RESULT:EXIT
2
p
p
. WARNING (3)
RESULT
.
SP :
5/4/0.1
.
DIST: 14.0/ 17.0ft
.
LVL : -9.0/ +6.5dB
[SET CANCEL
[]/[]:Up/Down
[ENTER]:Enter
Press l / h repeatedly to toggle between the
warning displays.
WARNING: W-1
< OUT OF PHASE >
Reverse Channel
FL
-CENTER
PL
PR
SL
SR
SBL
SBR
p
[ : Select
[]/[]
[ENTER] : Enter
y
• For details about each warning message, see the “AUTO
SETUP” section in “TROUBLESHOOTING” on
page 128.
• When the corresponding warning message is not
applicable to a speaker, “– –” is displayed instead.
3
Press ENTER to return to the top
“RESULT:EXIT” display.
PRESET/CH
RESULT:EXIT
ENTER
A-E/CAT.
p
p
WARNING (3)
RESULT
.
SP :
5/4/0.1
.
DIST: 14.0/ 17.0ft
.
LVL : -9.0/ +6.5dB
.[
SET CANCEL
[]/[]:Up/Down
[ENTER]:Enter
37 En
01EN_00_RX-V1700_U.book Page 38 Tuesday, June 27, 2006 9:37 AM
PLAYBACK
PLAYBACK
CAUTION
Extreme caution should be exercised when you play back CDs encoded in DTS. If you play back a CD
encoded in DTS on a DTS-incompatible CD player, you will only hear some unwanted noise that may
damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the
sound output level of your CD player before you play back a CD encoded in DTS.
y
To play DTS-encoded CDs when using a digital audio connection, set “DECODER MODE” in “INPUT MENU” to “DTS” before the
playback (see page 96).
Basic procedure
2
(U.S.A. model)
PURE DIRECT
Rotate the INPUT selector on the front panel
(or set the operation mode selector to AMP
and then press one of the input selector
buttons on the remote control) to select the
desired input source.
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
INPUT
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
VIDEO AUX
PHONES
ON
OFF
MASTER
2
5
Front panel
4
or
POWER
POWER
TV
AV
XM
STANDBY
POWER
AUDIO SEL
SLEEP
LEVEL
PRESET/CH
SET MENU
TITLE
PURE DIRECT
XM
MENU
SRCH MODE
BAND
AMP
PHONO
TUNER
CD
PHONO
AUDIO
ENTER
A-E/CAT.
V-AUX/DOCK CBL/SAT
DTV
VCR 1
TUNER
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
PARAMETER
2
SELECT
V-AUX/DOCK CBL/SAT
EFFECT
XM MEMORY
5
SOURCE
STRAIGHT
DISPLAY
RETURN
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
7
8
NIGHT
ENHANCER
9
0
+ 10
ENT
TV
DTV
VCR 1
Remote control
AMP
+
+
+
SOURCE
TV VOL
CH
VOLUME
–
–
–
TV MUTE
TV INPUT
MUTE
TV
2
4
REC
DISC SKIP
OFF
ON
MACRO
LEARN
CLEAR
RENAME
The name of the currently selected input source
appears in the front panel display and in the OSD for
a few seconds.
(U.S.A. model)
1
Available input sources
V-AUX
Turn on the video monitor connected to this
unit.
DVR/VCR 2
VCR 1 CBL/SAT
DTV
DVD
INPUT:
MD/TAPE
CD-R
CD
PHONO
MULTI CH
TUNER XM
DVD
y
• See page 42 to display the input source information.
• You can display a gray background in the OSD when there
is no video signal being input by setting “GRAY BACK”
in “OPTION MENU” to “AUTO” (see page 97).
• You can change the display settings by using “SHORT
MESSAGE” parameter in “DISPLAY SET”. See pages 98
for details.
38 En
Currently selected input
source
Note
For details about controlling XM Satellite Radio when
“XM” is selected as the input source, see page 65.
01EN_00_RX-V1700_U.book Page 39 Tuesday, June 27, 2006 9:37 AM
PLAYBACK
3
4
Note
Start playback on the selected source
component or select a broadcast station.
• Refer to the operating instructions for the source
component.
• See page 54 for details about tuning instructions.
• See page 65 for details about XM Satellite Radio
tuning instructions.
Sound field programs and the Compressed Music Enhancer
mode cannot be selected when the component connected to
the MULTI CH INPUT jacks is selected as the input source
(see page 41) and Audio input jack select is set to
“ANALOG” (see page 40).
Rotate VOLUME on the front panel (or press
VOLUME +/– on the remote control) to adjust
the volume to the desired output level.
• Choose a sound field program based on your listening
preference, not merely on the name of the program.
• When you select an input source, this unit automatically
selects the last sound field program used with the
corresponding input source.
• To display information about the currently selected input
source in the OSD, see page 76 for details.
VOLUME
■ Guide to contents
+
or
y
VOLUME
–
When you want to...
Front panel
Remote control
See page 51 to adjust the level of each speaker.
5
Rotate the PROGRAM selector on the front
panel (or press one of the sound field
program selector buttons on the remote
control repeatedly) to select the desired
sound field program.
The name of the selected sound field program appears
in the front panel display and in the OSD. See
page 45 for details about sound field programs.
or
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
1
2
3
4
Enjoy pure hi-fi stereo sound
50
Adjust the tonal quality of the front speakers
50
Enjoy the compressed music sources in enhanced
sound
52
Edit parameters of sound field programs
76
Enjoy the sources which have wide dynamic range at
night
53
Use headphones
41
Enjoy multi-channel sources in 2-channel stereo
51
Select a decoder to play back sources with
80
Set this unit to the standby mode automatically
43
STEREO
PROGRAM
Front panel
5
Remote control
Currently selected sound field program category
MOVIE
Sci-Fi
Currently selected sound field program
39 En
BASIC
OPERATION
y
See
page
01EN_00_RX-V1700_U.book Page 40 Tuesday, June 27, 2006 9:37 AM
PLAYBACK
AUTO
Selecting audio input jacks
(AUDIO SELECT)
This unit comes with a variety of input jacks. Use this
feature (Audio input jack select) to switch the input jack
assigned to an input source when more than one jacks are
assigned to an input source.
y
• We recommend setting Audio input jack select to “AUTO” in
most cases.
• You can adjust the default Audio input jack select of this unit by
using “AUDIO SELECT” in “OPTION MENU” (see page 99).
1
Rotate the INPUT selector on the front panel
(or press one of the input selector buttons on
the remote control) to select the desired
input source.
Automatically selects input signals in
the following order:
(1) HDMI
(2) Digital signals
(3) Analog signals
HDMI
Selects only HDMI signals. When
HDMI signals are not input, no sound
is output.
COAX/OPT Automatically selects input signals in
the following order:
(1) Digital signals input at the
COAXIAL jack.
(2) Digital signals input at the
OPTICAL jack.
When no signals are input, no sound is
output.
ANALOG
Selects only analog signals. If no
analog signals are input, no sound is
output.
INPUT
Note
PHONO
V-AUX/DOCK CBL/SAT
or
DTV
Front panel
2
VCR 1
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
Remote control
Press AUDIO SELECT on the front panel (or
AUDIO SEL on the remote control) repeatedly
to select the desired Audio input jack select
setting.
AUDIO
SELECT
AUDIO SEL
or
Available input sources
V-AUX
DVR/VCR 2
VCR 1 CBL/SAT
DTV
DVD
A.SEL:
MD/TAPE
CD-R
CD
PHONO
MULTI CH
TUNER XM
AUTO
Currently selected
Audio input jack
select setting
40 En
This feature is not available when no digital input jack
(OPTICAL, COAXIAL and HDMI) are assigned. In
addition, HDMI is not available as an Audio input jack
select setting when the HDMI IN 1 and HDMI IN 2 jacks
are not used. Use “I/O ASSIGNMENT” in “INPUT
MENU” to reassign the respective input jack (see page 94).
01EN_00_RX-V1700_U.book Page 41 Tuesday, June 27, 2006 9:37 AM
PLAYBACK
Selecting the MULTI CH INPUT
component
Use this feature to select the component connected to the
MULTI CH INPUT jacks (see page 26) as the input
source.
Using your headphones
Connect a pair of headphones with a stereo
analog audio cable plug to the PHONES jack on
the front panel.
Rotate the input selector on the front panel to
select MULTI CH INPUT (or MULTI CH IN on the
remote control).
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
INPUT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
VIDEO AUX
PHONES
ON
OFF
MASTER
MULTI CH IN
or
Front panel
Remote control
Use “MULTI CH SET” menu in “INPUT MENU” to set the
parameters for MULTI CH INPUT (see page 96).
y
When you select a sound field program, SILENT CINEMA mode
activates automatically (see page 49)
Note
Sound field programs and the Compressed Music Enhancer mode
cannot be selected when the component connected to the MULTI
CH INPUT jacks is selected as the input source and Audio input
jack select is set to “ANALOG” (see page 40).
Notes
• When you connect headphones, no signals are output at the
speaker terminals.
• When the component connected to the MULTI CH INPUT
jacks of this unit is selected as the input source and Audio input
jack select is set to “ANALOG” (see page 40), only the signals
input at FRONT jacks are output from the connected
headphones.
• All Dolby Digital and DTS audio signals are mixed down to the
left and right headphone channels.
Muting the audio output
Press MUTE on the remote control to mute the
audio output. Press MUTE again to resume the
audio output.
MUTE
y
• You can also rotate VOLUME on the front panel or press
VOLUME +/– on the remote control to resume the audio
output.
• You can adjust the muting level by using the “MUTE TYPE”
parameter in “SOUND MENU” (see page 93).
• The MUTE indicator flashes in the front panel display when the
audio output is muted and disappears from the front panel
display when the audio output is resumed.
41 En
BASIC
OPERATION
y
01EN_00_RX-V1700_U.book Page 42 Tuesday, June 27, 2006 9:37 AM
PLAYBACK
Displaying the input source
information
You can display the format, sampling frequency, channel,
bit rate and flag data of the current input signal.
1
Set the operation mode selector to AMP and
then press SET MENU on the remote control.
The top “SET MENU” display appears in the OSD.
AMP
SET MENU
MENU
.;AUTOSETUP
;MANUALSETUP
.;SIGNALINFO
SRCH MODE
TV
p
p
[ ]/[]:Up/Down
[ENTER]:Enter
2
Signal format FORMAT
Signal format. When this unit cannot detect a digital
signal, it automatically switches to analog input.
Note
“---” appears when this unit cannot detect any signals.
Sampling frequency SAMPLING
The number of samples per second taken from a
continuous signal to make a discrete signal.
SET MENU
SOURCE
■ Audio information
Press n repeatedly to select “SIGNAL INFO”
and then press ENTER.
The audio information about the input source appears
in the OSD.
Note
“---” appears when this unit cannot detect the sampling
frequency.
Channel CHANNEL
The number of source channels in the input signal
(front/surround/LFE). For example, a multi-channel
soundtrack with 3 front channels, 2 surround
channels and LFE, is displayed as “3/2/0.1”.
Note
“---” appears when there is no source channel available.
PRESET/CH
PRESET/CH
ENTER
ENTER
A-E/CAT.
Bit rate BITRATE
The number of bits passing a given point per second.
Note
A-E/CAT.
“---” appears when this unit cannot detect the bit rate.
3
Press k / n repeatedly to navigate the cursor
in the OSD and press l / h to toggle
between the audio and video information
displays.
PRESET/CH
Dialogue normalization level DIALOG
The dialogue normalization level preset to the current
input Dolby Digital and DTS signal.
Flag FLAG
Flag data encoded in DTS, Dolby Digital, or PCM
signals that cue this unit to automatically switch
decoders.
PRESET/CH
■ Video information
ENTER
ENTER
A-E/CAT.
A-E/CAT.
Navigating the cursor
4
Selecting the audio or
video information
Press SET MENU on the remote control again
to exit from “SET MENU”.
SET MENU
MENU
SRCH MODE
42 En
HDMI Signal Type HDMI SIGNAL
Type of the HDMI signals input or output at the
HDMI IN/OUT jacks of this unit.
HDMI Resolution HDMI RES.
Resolution of the HDMI signals input or output at the
HDMI IN/OUT jacks of this unit.
Analog Resolution ANALOG RES.
Resolution of the analog signals input or output at the
video jacks of this unit.
HDMI Error HDMI ERROR
Error message for HDMI sources or connected
HDMI devices. See page 127 for details.
01EN_00_RX-V1700_U.book Page 43 Tuesday, June 27, 2006 9:37 AM
PLAYBACK
Playing video sources in the
background of an audio source
3
You can combine a video image from a video source with
sound from an audio source. For example, you can enjoy
listening to classical music while viewing beautiful
scenery from the video source on the video monitor.
Press SLEEP on the remote control
repeatedly to set the amount of time.
Each time you press SLEEP, the front panel display
changes as shown below.
SLEEP
Press the input selector buttons on the remote
control to select a video source and then an
audio source.
SLEEP 120min.
SLEEP OFF
SLEEP 90min.
SLEEP 30min.
SLEEP 60min.
XM
PHONO
TUNER
V-AUX/DOCK CBL/SAT
DTV
VCR 1
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
The SLEEP indicator flashes while you are switching
the amount of time for the sleep timer. Once the sleep
timer is set, the SLEEP indicator lights up in the front
panel display, and the display returns to the selected
sound field program.
Audio sources
Video sources
120min.
SLEEP
y
Set the “BGV” parameter in the “MULTI CH SET” menu to the
desired setting to select the default background video input source
of the MULTI CH INPUT sources (see page 96).
Flashes
Using the sleep timer
Use this feature to automatically set the main zone to the
standby mode after a certain amount of time. The sleep
timer is useful when you are going to sleep while this unit
is playing or recording a source. The sleep timer also
automatically turns off any external components
connected to the AC OUTLET(S) (see page 29).
1
Press one of the input selector buttons on
the remote control to select the desired input
source.
STRAIGHT
Analog
SLEEP
Lights up
■ Canceling the sleep timer
Press SLEEP on the remote control repeatedly
until “SLEEP OFF” appears in the front panel
display.
SLEEP
XM
PHONO
TUNER
V-AUX/DOCK CBL/SAT
DTV
2
VCR 1
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
Start playback on the selected source
component or select a broadcast station.
Refer to the operating instructions for the source
component.
See page 54 for details about tuning instructions.
SLEEP
OFF
Disappears
The SLEEP indicator turns off, and “SLEEP OFF”
disappears from the front panel display after a few
seconds.
y
The sleep timer setting can also be canceled by pressing
STANDBY on the remote control (or MAIN ZONE ON/OFF on
the front panel) to set the main zone to the standby mode.
43 En
BASIC
OPERATION
SLEEP
01EN_00_RX-V1700_U.book Page 44 Tuesday, June 27, 2006 9:37 AM
SOUND FIELD PROGRAMS
SOUND FIELD PROGRAMS
This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from
almost any stereo or multi-channel sound source. This unit is also equipped with a YAMAHA digital sound field
processing (DSP) chip containing several sound field programs which you can use to enhance your playback experience.
y
• When you set the “DECODER MODE” parameter in “INPUT MENU” to “AUTO”, this unit selects the appropriate digital decoder
according to the input signal.
• The YAMAHA CINEMA DSP modes are compatible with all Dolby Digital, DTS, and Dolby Surround sources.
• The YAMAHA HiFi DSP sound field programs recreate real-world acoustic environments made from precise measurements taken in
actual concert halls, music venues, movie theaters, etc. Thus, you may notice variations in the strength of the reflections coming from
the front, back, left and right.
• You can change sound field parameters. See page 76 for details.
Selecting sound field programs
Notes
• When you select an input source, this unit automatically selects the last sound field program used with the corresponding input source.
• Sound field programs cannot be selected when the component connected to the MULTI CH INPUT jacks is selected as the input
source (see page 41) and Audio input jack select is set to “ANALOG” (see page 40).
• When you play back DSD sources with any sound field program, this unit converts the DSD signals to PCM signals and then applies
the selected program.
• When you play back DTS 96/24 sources with any sound field program, this unit applies the selected program without activating the
DTS 96/24 decoder.
• Sampling frequencies higher than 48 kHz are sampled down to 48 kHz or lower and then sound field programs are applied.
■ Front panel operations
■ Remote control operations
(U.S.A. model)
AMP
+
+
+
TV VOL
CH
VOLUME
AMP
SOURCE
PURE DIRECT
–
–
–
TV MUTE
TV INPUT
MUTE
TV
VOLUME
LEVEL
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
PRESET/CH
SET MENU
TITLE
MENU
BAND
SRCH MODE
PURE DIRECT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
SILENT CINEMA
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
AUDIO
ENTER
OPTICAL
A-E/CAT.
PARAMETER
PROGRAM
OPTIMIZER
MIC
PHONES
VIDEO AUX
ON
OFF
STRAIGHT
DISPLAY
RETURN
EFFECT
XM MEMORY
MASTER
PROGRAM selector
CLASSICAL
LIVE/CLUB
ENTERTAIN
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
9
0
MOVIE
7
8
NIGHT
ENHANCER
+ 10
ENT
Sound field program
selector buttons
(U.S.A. model)
Rotate the PROGRAM selector on the front panel.
The name of the selected sound field program appears in
the front panel display and in the OSD.
44 En
Set the operation mode selector to AMP and then
press one of the sound field program selector
buttons on the remote control repeatedly.
The name of the selected sound field program appears in
the front panel display and in the OSD.
01EN_00_RX-V1700_U.book Page 45 Tuesday, June 27, 2006 9:37 AM
SOUND FIELD PROGRAMS
Sound field program descriptions
y
Select a sound field program based on your listening preference, not merely on the name of the program, etc.
Remote control
button
Category of the
program
Name of the
program
Created sound
fields
(see page 11)
CINEMA DSP
or
HiFi DSP
MOVIE
4
MOVIE
Sci-Fi
This program clearly reproduces dialog and sound effects in the latest sound form for science fiction films, thus creating a broad and expansive
cinematic space amid silence. You can enjoy science fiction films in a virtual-space sound field that includes Dolby Surround, Dolby Digital and
DTS-encoded software employing the most advanced techniques.
DSP LEVEL
P.INIT. DLY
P.ROOM SIZE
S.INIT. DLY
S. ROOM SIZE
SB INI. DLY
SB ROOM SIZE
DIALG. LIFT
Program description
Available sound field parameters (see page 77)
■ For music audio sources
For audio music sources, we also recommend using the Pure Direct mode (see page 50), the “STRAIGHT” mode (see page 49) or
surround decode mode (see page 80).
CLASSICAL
ENTERTAIN
1
3
CLASSICAL
Hall in Munich
HiFi DSP
This is a large fan-shaped concert hall which has approximately 2500 seats. Almost the whole interior is made of wood. There is relatively
little reflection from the walls, and sound spreads finely and beautifully.
DSP LEVEL
INIT. DLY
CLASSICAL
ENTERTAIN
1
3
ROOM SIZE
LIVENESS
CLASSICAL
DIALG.LIFT
Hall in Vienna
HiFi DSP
A classic shoe-box type concert hall with approximately 1700 seats. Pillars and ornate carvings create extremely complex reflections which
produce a very full, rich sound.
DSP LEVEL
INIT. DLY
CLASSICAL
ENTERTAIN
1
3
ROOM SIZE
LIVENESS
CLASSICAL
DIALG.LIFT
Hall in Amsterdam
HiFi DSP
This is a large 2200 seat shoe-box type concert hall in Amsterdam. It has a circular stage with seats located behind the stage.
DSP LEVEL
INIT. DLY
CLASSICAL
ENTERTAIN
1
3
ROOM SIZE
LIVENESS
CLASSICAL
DIALG.LIFT
Church in Freiburg
HiFi DSP
This program creates the acoustic environment of a big church located in south Germany. The reverberation delay is very long while the early
reflections are smaller than with other sound field programs.
DSP LEVEL
INIT. DLY
LIVENESS
REV.TIME
REV.DELAY
REV. LEVEL
DIALG.LIFT
45 En
BASIC
OPERATION
y
01EN_00_RX-V1700_U.book Page 46 Tuesday, June 27, 2006 9:37 AM
SOUND FIELD PROGRAMS
CLASSICAL
1
CLASSICAL
Chamber
HiFi DSP
This program creates a relatively wide space with a high ceiling like an audience hall in a palace. It offers pleasant reverberations that are
suitable for courtly music and chamber music.
DSP LEVEL
INIT. DLY
LIVE/CLUB
2
LIVENESS
REV.TIME
LIVE/CLUB
REV.DELAY
REV. LEVEL
DIALG.LIFT
Village Vanguard
HiFi DSP
A traditional jazz club in New York, located on 7th Avenue. This room has a low ceiling, and the “stage” is located at the corner of the room.
This program creates an intimate “close-to-the music” feel.
DSP LEVEL
INIT. DLY
LIVE/CLUB
2
ROOM SIZE
LIVENESS
LIVE/CLUB
DIALG.LIFT
Warehouse Loft
HiFi DSP
This program simulates a space enclosed by concrete. An energetic sound field is created with relatively clear reflections from the walls.
DSP LEVEL
INIT. DLY
LIVE/CLUB
2
ROOM SIZE
LIVENESS
LIVE/CLUB
REV.TIME
REV.DELAY
REV. LEVEL
DIALG.LIFT
Cellar Club
HiFi DSP
This program simulates a live house with a low ceiling and homey atmosphere. A realistic, live sound field features powerful sound as if the
listener is in a row in front of a small stage.
DSP LEVEL
INIT. DLY
LIVE/CLUB
2
ROOM SIZE
LIVENESS
LIVE/CLUB
DIALG.LIFT
The Roxy Theatre
HiFi DSP
The ideal program for lively, dynamic rock music. The data for this program was recorded at LA’s hottest rock club. The listener’s virtual seat
is at the center-left of the hall.
DSP LEVEL
INIT. DLY
LIVE/CLUB
2
ROOM SIZE
LIVENESS
LIVE/CLUB
REV.TIME
REV.DELAY
REV. LEVEL
DIALG.LIFT
The Bottom Line
HiFi DSP
This is the sound field at stage front in The Bottom Line, a famous New York jazz club. The floor can seat 300 people to the left and right in a
sound field offering real and vibrant sound.
DSP LEVEL
INIT. DLY
ROOM SIZE
LIVENESS
DIALG.LIFT
■ For various sources
Note
The available sound field parameters and the created sound fields differ depending on the input sources and the settings of this unit.
ENTERTAIN
3
ENTERTAINMENT
Sports
This program allows the listeners to enjoy stereo sport broadcasts and studio variety programs with enriched live feeling. In sports broadcasts,
the voices of the commentator and sportscaster are positioned clearly on the center while the atmosphere of the stadium expands in an
optimum space to offer the listeners with a feeling of presence in the stadium.
DSP LEVEL
P. INIT. DLY
46 En
P. ROOM SIZE
S. INIT. DLY
S. ROOM SIZE
SB INI. DLY
SB ROOM SIZE
DIALG.LIFT
01EN_00_RX-V1700_U.book Page 47 Tuesday, June 27, 2006 9:37 AM
SOUND FIELD PROGRAMS
ENTERTAIN
3
ENTERTAINMENT
Action Game
This sound field has been optimized for action games such as car racing and FPS games. It uses the reflection data that limits the effects range
per channel in order to offer a powerful playing environment with a being-there feeling by enhancing various effects tones while maintaining
a clear sense of directions.
DSP LEVEL
P. INIT. DLY
ENTERTAIN
3
P. ROOM SIZE
S. INIT. DLY
ENTERTAINMENT
S. ROOM SIZE
SB INI. DLY
SB ROOM SIZE
DIALG.LIFT
Roleplaying Game
This sound field has been optimized for role-playing and adventure games. It combines the sound field effects for movies and the sound field
design used with “Action Game” to represent the depth and 3D feeling of the field during play, while offering movie-like surround effects in
the movie scenes in the game.
DSP LEVEL
P. INIT. DLY
P. ROOM SIZE
S. INIT. DLY
S. ROOM SIZE
SB INI. DLY
SB ROOM SIZE
DIALG.LIFT
■ For visual sources of music
Note
LIVE/CLUB
ENTERTAIN
2
3
ENTERTAINMENT
Music Video
HiFi DSP
This sound field offers an image of a concert hall for live performance of pop, rock and jazz music. The listener can indulge oneself in a hot
live space thanks to the presence sound field that emphasizes the vividness of vocals and solo play and the beat of rhythm instruments, and to
the surround sound field that reproduces the space of a big live hall.
DSP LEVEL
P. INIT. DLY
ENTERTAIN
3
P. ROOM SIZE
S. INIT. DLY
ENTERTAINMENT
S. ROOM SIZE
SB INI. DLY
SB ROOM SIZE
DIALG.LIFT
Recital/Opera
This program controls the amount of reverberations at an optimum level and emphasizes the depth and clarity of human voices. “Opera”
offers the reverberations of an orchestra box in front of the listener at the same time as providing the acoustic positioning and feeling of
presence on the stage. The surround sound field is relatively moderate, but the data for concert hall effects are used to represent the inherent
beauty of music, The listener will not be fatigued even after long hours of opera entertainment.
DSP LEVEL
P. INIT. DLY
P. ROOM SIZE
S. INIT. DLY
S. ROOM SIZE
SB INI. DLY
SB ROOM SIZE
DIALG.LIFT
■ For movie sources
y
You can select the desired decoder used with following sound field program (except “Mono Movie”). See page 82 for details.
Note
The available sound field parameters and the created sound fields differ depending on the input sources and the settings of this unit.
MOVIE
4
MOVIE
Standard
This program create a sound field emphasizing the surrounding feeling without disturbing the original acoustic positioning of multi-channel
audio such as Dolby Digital and DTS. It has been designed with the concept of “an ideal movie theater”, in which the audience is surrounded
by beautiful reverberations from the left, right and rear.
DSP LEVEL
S. INIT. DLY
S. ROOM SIZE
S. LIVENESS
SB INI. DLY
SB ROOM SIZE
SB LIVENESS
DIALG.LIFT
47 En
BASIC
OPERATION
The available sound field parameters and the created sound fields differ depending on the input sources and the settings of this unit.
01EN_00_RX-V1700_U.book Page 48 Tuesday, June 27, 2006 9:37 AM
SOUND FIELD PROGRAMS
MOVIE
MOVIE
4
Spectacle
This program creates the extremely wide sound field of a 70-mm movie theater. It precisely reproduces the source sound in detail, making
both the video and the sound field incredibly real. This is ideal for any kind of video source encoded with Dolby Surround, Dolby Digital or
DTS (especially large-scale movie productions).
DSP LEVEL
P. INIT. DLY
P. ROOM SIZE
S. INIT. DLY
S. ROOM SIZE
SB INI. DLY
MOVIE
Sci-Fi
MOVIE
4
SB ROOM SIZE
DIALG.LIFT
This program clearly reproduces dialog and sound effects in the latest sound form for science fiction films, thus creating a broad and
expansive cinematic space amid silence. You can enjoy science fiction films in a virtual-space sound field that includes Dolby Surround,
Dolby Digital and DTS-encoded software employing the most advanced techniques.
DSP LEVEL
P. INIT. DLY
P. ROOM SIZE
S. INIT. DLY
MOVIE
MOVIE
4
S. ROOM SIZE
SB INI. DLY
SB ROOM SIZE
DIALG.LIFT
Adventure
This program is ideal for precisely reproducing the sound design of the newest 70-mm and multichannel soundtrack films. The sound field is
made to be similar to that of the newest movie theaters, so the reverberations of the sound field itself are restrained as much as possible.
DSP LEVEL
P. INIT. DLY
P. ROOM SIZE
S. INIT. DLY
MOVIE
MOVIE
4
S. ROOM SIZE
SB INI. DLY
SB ROOM SIZE
DIALG.LIFT
Drama
This sound field features stable reverberations that match a wide range of movie genres from serious dramas to musicals and comedies. The
reverberations are modest but offer an optimum 3D feeling, reproducing effects tones and background music softly but cubically around clear
words and center positioning in a way that does not fatigue the listener even after long hours of viewing.
DSP LEVEL
P. INIT. DLY
P. ROOM SIZE
S. INIT. DLY
MOVIE
MOVIE
4
S. ROOM SIZE
SB INI. DLY
SB ROOM SIZE
DIALG.LIFT
Mono Movie
This program is provided for reproducing monaural video sources (such as old movies). The program produces the optimum reverberation to
create sound depth using only the presence sound field.
DSP LEVEL
INIT. DLY
ROOM SIZE
LIVENESS
REV.TIME
REV. LEVEL
REV.DELAY
DIALG.LIFT
■ Stereo playback
STEREO
5
STEREO
2ch STEREO
Use this program to mix down multi-channel sources to 2 channels. See page 51 for details.
DIRECT
STEREO
5
STEREO
7ch STEREO
HiFi DSP
Use this program to output sound from all speakers. When you play back multi-channel sources, this unit downmixes the source to 2
channels, and then output the sound from all speakers. This program creates a larger sound field and is ideal for background music at parties,
etc.
CT LEVEL
SL LEVEL
48 En
SR LEVEL
SB LEVEL
PL LEVEL
PR LEVEL
01EN_00_RX-V1700_U.book Page 49 Tuesday, June 27, 2006 9:37 AM
SOUND FIELD PROGRAMS
■ Using sound field programs without
surround speakers
(Virtual CINEMA DSP)
Enjoying unprocessed input
sources
Virtual CINEMA DSP allows you to enjoy the CINEMA
DSP programs without surround speakers. It creates
virtual speakers to reproduce the natural sound field.
When you set “SUR. L/R SP” to “NONE” (see page 88),
Virtual CINEMA DSP activates automatically whenever
you select a CINEMA DSP sound field program (see
page 45).
When this unit is in the “STRAIGHT” mode, 2-channel
stereo sources are output from only the front left and right
speakers. Multi-channel sources are decoded straight into
the appropriate channels without any additional effect
processing.
Note
Press STRAIGHT on the front panel (or on the
remote control) to select “STRAIGHT”.
Virtual CINEMA DSP will not activate even when “SUR. L/R
SP” is set to “NONE” (see page 88) in the following cases:
– when the component connected to the MULTI CH INPUT
jacks is selected as the input source (see page 41).
– when headphones are connected to the PHONES jack.
– when the Pure Direct (see page 50) or “2ch Stereo” mode (see
page 51) is selected, or when this unit is in the “STRAIGHT”
mode (see page 49).
SILENT CINEMA allows you to enjoy multi-channel
music or movie sound, including Dolby Digital and DTS
sources, through ordinary headphones. SILENT CINEMA
activates automatically whenever you connect headphones
to the PHONES jack while listening to CINEMA DSP or
HiFi DSP sound field programs (see page 45). When
activated, the SILENT CINEMA indicator lights up in the
front panel display.
Notes
• SILENT CINEMA does not activate when the component
connected to the MULTI CH INPUT jacks is selected as the
input source (see page 41).
• SILENT CINEMA is not effective when the Pure Direct (see
page 50) or “2ch Stereo” mode (see page 51) is selected, or
when this unit is in the “STRAIGHT” mode (see page 49).
STRAIGHT
or
EFFECT
EFFECT
STRAIGHT
Format
Dolby Digital
Description
Standard processing for Dolby
Digital sources.
DTS
Standard processing for DTS
sources. When the input source is
DTS ES Discrete or DTS ES
Matrix format, the respective
indicator appears in the front
panel display.
DSD
Plays back DSD (Direct Stream
Digital) sources.
PCM
Plays back PCM (Pulse Code
Modulation) sources.
Plays back multi-channel PCM
(Pulse Code Modulation) sources.
MPCM
Analog
Plays back analog sources.
■ Deactivating the “STRAIGHT” mode
Press STRAIGHT on the remote control so that
“STRAIGHT” disappears from the front panel
display.
The sound effect is turned back on.
STRAIGHT
STRAIGHT
or
EFFECT
EFFECT
49 En
BASIC
OPERATION
■ Enjoying multi-channel sources and
sound field programs with headphones
(SILENT CINEMA)
STRAIGHT
01EN_00_RX-V1700_U.book Page 50 Tuesday, June 27, 2006 9:37 AM
USING AUDIO FEATURES
USING AUDIO FEATURES
Enjoying pure hi-fi sound
Adjusting the tonal quality
Use the Pure Direct mode to enjoy the pure fidelity sound
of the selected source. When the Pure Direct mode is
activated, this unit plays back the selected source with the
least circuitry.
Use this feature to adjust the balance of bass and treble for
the front L/R, center, presence L/R speaker channels and
the subwoofer channel.
1
Press PURE DIRECT on the front panel (or on the
remote control) to turn on or off the Pure Direct
mode.
The PURE DIRECT button on the front panel lights up
while this unit is in the Pure Direct mode. The front panel
display automatically dims.
Press TONE CONTROL on the front panel
repeatedly to select the high-frequency
response (TREBLE) or the low-frequency
response (BASS)
TONE
CONTROL
PURE DIRECT
or
PURE DIRECT
2
Front panel
Remote control
Rotate the PROGRAM selector to adjust the
high-frequency response (TREBLE) or the
low-frequency response (BASS).
Notes
• When you play back the multi-channel PCM sources (less than
192 kHz), this unit downmixes the multi-channel signals
according to the “SPEAKER SET” in “BASIC MENU” (see
page 87).
• When the component connected to the HDMI IN jacks is
selected as the input source and Audio input jack select is set to
“AUTO” or “HDMI”, this unit does not turn off the video
circuitry in the Pure Direct mode.
• When you set Audio input jack select to “AUTO”, “HDMI” or
“COAX/OPT” (see page 40) and play back the Dolby Digital,
DTS or multi channel PCM sources, this unit activates the
corresponding decoder.
• The following operations are not possible when this unit is in
the Pure Direct mode:
– switching the sound field program
– displaying the OSD
– adjusting the “SET MENU” parameters (except for speaker
level settings)
– operating video functions (video conversion, etc.)
• The Pure Direct mode is automatically canceled whenever this
unit is turned off.
y
The front panel display turns on momentarily when an operation
is performed.
50 En
PROGRAM
■ Bypassing the tone control circuitry
Press TONE CONTROL repeatedly to select
BYPASS and cancel the tone control.
TONE
CONTROL
Notes
• If you increase or decrease the high-frequency or the
low-frequency sound to an extreme level, the tonal quality of
the surround speakers may not match that of the front L/R,
center, presence L/R speakers and the subwoofer.
• TONE CONTROL is not effective when PURE DIRECT is
selected, or when MULTI CH INPUT is selected as the input
source.
01EN_00_RX-V1700_U.book Page 51 Tuesday, June 27, 2006 9:37 AM
USING AUDIO FEATURES
Adjusting the speaker level
You can adjust the output level of each speaker while
listening to a music source. This is also possible when
playing sources input at the MULTI CH INPUT jacks.
Note
This operation will override the level adjustments made in
“AUTO SETUP” (see page 32) and “SP LEVEL” (see page 90).
1
Enjoying multi-channel sources in
2-channel stereo
You can mix down multi-channel sources to 2 channels
and enjoy playback in 2-channel stereo.
1
Set the operation mode to AMP and then
press STEREO on the remote control
repeatedly to select “2ch Stereo”.
Set the operation mode selector to AMP and
then press LEVEL on the remote control
repeatedly to select the speaker you want to
adjust.
AMP
STEREO
SOURCE
5
TV
AMP
LEVEL
SOURCE
TITLE
BAND
TV
Adjusted speaker
FRONT L
Front left speaker
CENTER
Center speaker
FRONT R
Front right speaker
SUR. R
Surround right speaker
SB L
Surround back right speaker
SB R
Surround back left speaker
SUR. L
Surround left speaker
SWFR
Subwoofer
PRNS L
Presence left speaker
PRNS R
Presence right speaker
y
• You can use a subwoofer with this program when “LFE/BASS
OUT” is set to “SWFR” or “BOTH” (see page 87).
• You can also select the “2ch Stereo” mode by rotating the
PROGRAM selector on the front panel.
2
Press PARAMETER and then l / h to set the
“DIRECT” parameter.
PRESET/CH
PARAMETER
y
• Once you press LEVEL on the remote control, you can
also select the speaker by pressing k / n.
• Instead of “SB R” and “SB L”, “SB” is displayed if “SUR.
B L/R SP” is set to either “SMLx1” or “LRGx1” (see
page 89).
2
Press l / h on the remote control to adjust
the speaker output level.
• Press i to increase the value.
• Press j to decrease the value.
Control range: –10 dB to +10 dB
PRESET/CH
ENTER
A-E/CAT.
DISPLAY
ENTER
A-E/CAT.
Choices: AUTO, OFF
• Select “AUTO” to bypass the decoders, DSP
processors and the tone control circuitry only when
“BASS” and “TREBLE” are set to 0 dB (see
page 50).
• Select “OFF” not to bypass the decoders, DSP
processors and the tone control circuitry when
“BASS” and “TREBLE” are set to 0 dB.
y
• When multi-channel signals (Dolby Digital and DTS) are
input, they are downmixed to 2 channels and output from
the front left and right speakers.
• The low-frequency signals input from the front left and
right speakers are redirected to the subwoofer in the
following cases:
–“LFE/BASS OUT” is set to “BOTH” (see page 87).
–“FRONT SP” is set to “SMALL” (see page 88) and
“LFE/BASS OUT” is set to “SWFR” (see page 87).
• Press PARAMETER again to exit from the parameter
setting mode.
51 En
BASIC
OPERATION
Display
2ch Stereo
01EN_00_RX-V1700_U.book Page 52 Tuesday, June 27, 2006 9:37 AM
USING AUDIO FEATURES
Selecting the Compressed Music
Enhancer mode
Compression artifacts (such as the MP3 format) are
created by a lossy compression scheme where the audio is
resampled to lower the bit rate and to remove sounds that
are indistinguishable to typical human hearing. The
Compressed Music Enhancer feature of this unit enhances
your listening experience by regenerating the missing
harmonics in a compression artifact. As a result, flattened
complexity due to the loss of high-frequency fidelity as
well as lack of bass due to the loss of low-frequency bass
is compensated, providing improved performance of the
overall sound system.
Notes
• When you play back DSD sources or PCM sources whose
sampling frequencies are higher than 48 kHz, this unit samples
them down to 48 kHz or lower and applies the Compressed
Music Enhancer mode.
• The Compressed Music Enhancer mode is not effective with
any of the sound field programs.
Choices: 2ch Enhancer, 7ch Enhancer, Off
• Select “2ch Enhancer” to play back compression
artifacts in 2-channel stereo.
• Select “7ch Enhancer” to play back compression
artifacts in 7-channel stereo.
• Select “Off” to turn off the Compressed Music
Enhancer mode.
Note
When you select “Off”, this unit returns to the previously
selected sound field program.
■ Changing the parameter of the
Compressed Music Enhancer mode
Press PARAMETER and then l / h on the
remote control to select the desired effect level.
The following display is shown in the OSD.
PRESET/CH
PARAMETER
DISPLAY
ENTER
A-E/CAT.
Press ENHANCER on the front panel (or set the
operation mode selector to AMP and then press
ENHANCER on the remote control) repeatedly to
select the desired Compressed Music Enhancer
mode.
The following display is shown in the OSD and the
ENHANCER indicator lights up in the front panel display.
MUSIC ENHANCER
2ch Stereo
. LOW
[HIGH
AMP
ENHANCER
or
SOURCE
ENHANCER
ENT
TV
Choices: HIGH, LOW
• Select “HIGH” for a high effect level.
• Select “LOW” for a low effect level.
y
Press PARAMETER to turn off the Compressed Music
Enhancer mode parameter display.
ENHANCER
MUSICENHANCER
2chEnhancer
52 En
Lights up
Note
Set the effect level to “HIGH” or “LOW” according to the
characteristics of a source. The high-frequency signals of
some sources may be emphasized too much. In this case, set
the effect level to “LOW”.
01EN_00_RX-V1700_U.book Page 53 Tuesday, June 27, 2006 9:37 AM
USING AUDIO FEATURES
Selecting the night listening mode
The night listening modes are designed to improve
listenability at lower volumes or at night. Choose either
“NIGHT:CINEMA” or “NIGHT:MUSIC” depending on
the type of material you are playing.
1
Press NIGHT on the front panel (or set the
operation mode selector to AMP and then
press NIGHT on the remote control)
repeatedly to select “NIGHT:CINEMA” or
“NIGHT:MUSIC”.
y
“NIGHT:CINEMA” and “NIGHT:MUSIC” adjustments are
stored independently.
Notes
• You cannot use the night listening modes in the following
cases:
–when the Pure Direct mode (see page 50) is selected.
–when the component connected to the MULTI CH
INPUT jacks is selected as the input source (see
page 41).
–when headphones are connected to the PHONES jack.
• The night listening modes may vary in effectiveness
depending on the input source and surround sound settings
you use.
AMP
NIGHT
SOURCE
or
NIGHT
+ 10
TV
BASIC
OPERATION
Choices: NIGHT:CINEMA, NIGHT:MUSIC, OFF
• Select “NIGHT:CINEMA” when watching films to
reduce the dynamic range of film soundtracks and
make dialog easier to hear at lower volumes.
• Select “NIGHT:MUSIC” when listening to music
sources to preserve ease-of-listening for all sounds.
• Select “OFF” if you do not want to use this feature.
y
When a night listening mode is selected, the NIGHT
indicator lights up in the front panel display.
2
Press l / h on the remote control to adjust
the effect level while “NIGHT:CINEMA” or
“NIGHT:MUSIC” is displayed in the front
panel display.
PRESET/CH
ENTER
A-E/CAT.
Remote control
Effect.Lvl:MID
Choices: MIN, MID, MAX
• Select “MIN” for minimum compression.
• Select “MID” for standard compression.
• Select “MAX” for maximum compression.
53 En
01EN_00_RX-V1700_U.book Page 54 Tuesday, June 27, 2006 9:37 AM
FM/AM TUNING
FM/AM TUNING
There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and
there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use
the automatic and manual preset tuning features to store up to 40 stations (A1 to E8: 8 preset station numbers in each of
the 5 preset station groups). Furthermore, you can recall any preset stations and exchange the assignment of two preset
stations with each other.
Note
Orient the connected FM and AM antennas for the best reception.
FM/AM controls and functions
■ Front panel functions
1
2
AUDIO
SELECT
■ Remote control functions
3
45 6 7
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
PHONO
1
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
VCR 1
1
EDIT
ZONE ON/OFF
STRAIGHT
SILENT CINEMA
S VIDEO
VIDEO
OPTIMIZER
MIC
PHONES
CD-R
2
3
STANDBY
CBL/SAT MD/TAPE PHONO
5
VCR 1 DVR/VCR 2
ZONE 3
L
R
AUDIO
7
OPTICAL
6
ENT
DVD
V-AUX/DOCK
9
0
VIDEO AUX
1 INPUT selector
Selects “TUNER” as the input source.
+
+
+
TV VOL
CH
VOLUME
2
3
–
–
–
TV MUTE
TV INPUT
MUTE
LEVEL
PRESET/CH
SET MENU
TITLE
MENU
BAND
SRCH MODE
4 PRESET/TUNING, EDIT
• Switches the function of PRESET/TUNING/CH l / h
between selecting preset station numbers and selecting
the tuning frequency.
• Edits the assignments of preset stations (see page 58).
5 FM/AM
Switches the reception band between FM and AM (see
page 55).
6 MEMORY
Stores a preset station in the memory. Hold down this
button for more than 3 seconds to start automatic preset
tuning (see page 57).
7 TUNING MODE
Switches between automatic tuning (the AUTO indicator
is turned on) and manual tuning (the AUTO indicator is
turned off) (see page 55).
3
5
VOLUME
PRESET
A/B/C/D/E
MUTE
A-E/CAT.
DISPLAY
PARAMETER
STRAIGHT
DISPLAY
5
EFFECT
XM MEMORY
3 PRESET/TUNING/CH l / h
• Selects one of the 8 preset station numbers (1 to 8)
when the colon (:) is displayed in the front panel
display (see page 57).
• Selects the tuning frequency when the colon (:) is not
displayed in the front panel display (see page 56).
Set to
SOURCE
PURE DIRECT
A-E/CAT.
RETURN
4
TV
AUDIO
ENTER
CLASSICAL
2 A/B/C/D/E
Selects one of the 5 preset station groups (A to E) (see
page 57).
8
AMP
(U.S.A. model)
54 En
CD
SELECT
ZONE 2
SOURCE
PROGRAM
1
4
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
TUNER
DTV
DISPLAY
SEARCH MODE
CATEGORY
INPUT
POWER
XM
DTV
TUNING
MODE
TUNER
V-AUX/DOCK CBL/SAT
LIVE/CLUB
ENTERTAIN
1
2
3
4
SUR. DECODE
SELECT
EXTD SUR.
5
6
7
8
NIGHT
ENHANCER
9
0
+ 10
ENT
PRESET
ID1 ID2
CAT.
ZONE 2 ZONE 3
NUMBER
MOVIE
STEREO
PRESET/CH
ALL
(U.S.A. model)
1 TUNER
Selects “TUNER” as the input source. This unit is turned
into the last selected station.
2 BAND
Switches the reception band between FM and AM (see
page 55). This unit is turned into the last selected AM or
FM station.
3 PRESET/CH k / n
Selects one of the 8 preset station numbers (1 to 8) when
the colon (:) is displayed in the front panel display (on
page 58).
4 Numeric buttons
Use numbers 1 through 8 to select preset stations (see
page 59).
5 A-E/CAT. l / h, A/B/C/D/E
Selects one of the preset station groups (A to E) (see
page 57).
01EN_00_RX-V1700_U.book Page 55 Tuesday, June 27, 2006 9:37 AM
FM/AM TUNING
Automatic tuning
3
Automatic tuning is effective when station signals are
strong and there is no interference.
Press TUNING MODE so that the AUTO
indicator lights up in the front panel display.
TUNING
MODE
DISPLAY
(U.S.A. model)
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
PHONES
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
AFM88.9MHz
VIDEO AUX
AUTO
ON
OFF
MASTER
1
1
No colon (:)
4 32 3
Lights up
If a colon (:) appears in the front panel display, tuning
is not possible. Press PRESET/TUNING to turn the
colon (:) off.
Rotate the INPUT selector to select “TUNER”
as the input source.
EDIT
SEARCH MODE
4
Front panel
2
Press FM/AM to select the reception band.
“FM” or “AM” appears in the front panel display.
Press PRESET/TUNING/CH l / h once to
begin automatic tuning.
When this unit is tuned into a station, the TUNED
indicator lights up and the frequency of the received
station is shown in the front panel display.
• Press h to tune into a higher frequency.
• Press l to tune into a lower frequency.
FM/AM
FM
or
AM
PRESET/TUNING/CH
AFM88.9MHz
TUNED
Lights up
55 En
BASIC
OPERATION
PRESET/
TUNING
INPUT
01EN_00_RX-V1700_U.book Page 56 Tuesday, June 27, 2006 9:37 AM
FM/AM TUNING
Manual tuning
3
If the signal received from the station you want to select is
weak, tune into it manually.
Press TUNING MODE so that the AUTO
indicator disappears from the front panel
display.
TUNING
MODE
Note
DISPLAY
Manually tuning into an FM station automatically switches the
tuner to monaural reception to increase the signal quality.
(U.S.A. model)
AFM88.9MHz
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
No colon (:)
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
PHONES
S VIDEO
ZONE 2
ZONE 3
L
R
VIDEO
AUDIO
OPTICAL
VIDEO AUX
ON
OFF
If a colon (:) appears in the front panel display, tuning
is not possible. Press PRESET/TUNING (EDIT) to
turn the colon (:) off.
MASTER
1
4 32 3
PRESET/
TUNING
EDIT
1
Rotate the INPUT selector to select “TUNER”
as the input source.
SEARCH MODE
4
INPUT
Press PRESET/TUNING/CH l / h to tune
into the desired station manually.
Hold down the button to continue searching.
PRESET/TUNING/CH
Front panel
2
Press FM/AM to select the reception band.
“FM” or “AM” appears in the front panel display.
FM/AM
FM
56 En
or
AM
01EN_00_RX-V1700_U.book Page 57 Tuesday, June 27, 2006 9:37 AM
FM/AM TUNING
Automatic preset tuning
3
You can use the automatic preset tuning feature to store up
to 40 FM stations with strong signals (A1 to E8: 8 preset
station numbers in each of the 5 preset station groups) in
order. You can then recall any preset station easily by
selecting the preset station number.
Press and hold MEMORY for more than 3
seconds.
The preset station number as well as the MEMORY
and AUTO indicators flashes. After approximately 5
seconds, automatic presetting starts from the current
frequency and proceeds toward higher frequencies.
MEMORY
(U.S.A. model)
MAN'L/AUTO FM
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
PHONES
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
A1:FM88.9MHz
VIDEO AUX
AUTO MEMORY
ON
OFF
MASTER
1
Rotate the INPUT selector to select “TUNER”
as the input source.
Front panel
Press FM/AM to select “FM” as the reception
band.
“FM” appears in the front panel display.
FM/AM
When automatic preset tuning is completed, the front
panel display shows the frequency of the last preset
station.
y
INPUT
2
Flashes
FM
• You can specify the preset number from which this unit
stores FM stations. Press A/B/C/D/E and then PRESET/
TUNING/CH l / h repeatedly after you perform step 3
to select the preset station number under which the first
station will be stored.
• You can begin tuning toward lower frequencies to store
FM stations automatically. Press PRESET/TUNING so
that the colon (:) disappears from the front panel display
and then press PRESET/TUNING/CH l after pressing
and holding MEMORY for more than 3 seconds.
Notes
• Any stored station data existing under a preset station
number is cleared when you store a new station under the
same preset station number.
• If the number of received stations does not reach 40 (E8),
automatic preset tuning automatically stops after
searching for all the available stations.
• Only FM stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station
you want to store is weak in signal strength, tune into it
manually and store it as described in “Manual preset
tuning” on page 58.
57 En
BASIC
OPERATION
1
Flashes
2 3
01EN_00_RX-V1700_U.book Page 58 Tuesday, June 27, 2006 9:37 AM
FM/AM TUNING
Manual preset tuning
4
You can also store up to 40 stations (A1 to E8: 8 preset
station numbers in each of the 5 preset station groups)
manually.
Press PRESET/TUNING/CH l / h to select a
preset station number (1 to 8) while the
MEMORY indicator is flashing.
• Press h to select a higher preset station number.
• Press l to select a lower preset station number.
(U.S.A. model)
PRESET/TUNING/CH
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
INPUT
DISPLAY
SEARCH MODE
CATEGORY
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
S VIDEO
VIDEO
PHONES
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
VIDEO AUX
ON
OFF
MASTER
A1:FM88.9MHz
3 4
2,5
Preset station number
1
2
MEMORY
Tune into a station automatically or manually.
See pages 55 and 56 for tuning instructions.
Press MEMORY.
The MEMORY indicator flashes in the front panel
display for approximately 5 seconds.
5
Flashes
Press MEMORY while the MEMORY indicator
is flashing.
The station band and frequency appear in the front
panel display with the preset station group and
number you have selected. The MEMORY indicator
disappears from the front panel display.
MEMORY
MAN'L/AUTO FM
MEMORY
MEMORY
MAN'L/AUTO FM
Flashes
3
Press A/B/C/D/E repeatedly to select a preset
station group (A to E) while the MEMORY
indicator is flashing.
The selected preset station group letter appears.
Check that the colon (:) appears in the front panel
display.
A1:FM88.9MHz
The displayed station has been stored as A1.
A/B/C/D/E
CATEGORY
A :FM88.9MHz
Preset station Colon (:)
group
58 En
Notes
MEMORY
Flashes
• Any stored station data existing under a preset station
number is cleared when you store a new station under the
same preset station number.
• The reception mode (stereo or monaural) is stored along
with the station frequency.
01EN_00_RX-V1700_U.book Page 59 Tuesday, June 27, 2006 9:37 AM
FM/AM TUNING
Selecting preset stations
2
You can tune into any desired station simply by selecting
the preset station group and number under which it was
stored.
(U.S.A. model)
Press PRESET/TUNING/CH l / h on the
front panel (or PRESET/CH k / n on the
remote control) to select the desired preset
station number (1 to 8).
The preset station group and number appear in the
front panel display along with the station band and
frequency.
PURE DIRECT
PRESET/CH
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
TUNING
MODE
MEMORY
FM/AM
MAN'L/AUTO FM
ENHANCER
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
SILENT CINEMA
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
S VIDEO
ZONE 2
ZONE 3
L
R
VIDEO
AUDIO
PRESET/TUNING/CH
OPTICAL
or
VIDEO AUX
PHONES
ENTER
ON
OFF
MASTER
A-E/CAT.
1 2
Front panel
Remote control
AMP
+
+
+
TV VOL
CH
VOLUME
SOURCE
–
–
–
TV MUTE
TV INPUT
MUTE
1,2
PRESET/CH
SET MENU
TITLE
MENU
BAND
SRCH MODE
1
BASIC
OPERATION
LEVEL
TV
PURE DIRECT
A1:FM88.9MHz
AUDIO
ENTER
A-E/CAT.
PARAMETER
RETURN
STRAIGHT
DISPLAY
EFFECT
XM MEMORY
(U.S.A. model)
y
When performing this operation with the remote control, set the
operation mode selector to SOURCE and then press TUNER to
select “TUNER” as the input source.
1
Press A/B/C/D/E on the front panel (or set the
operation mode selector to SOURCE and
then press A-E/CAT. l / h on the remote
control) to select the desired preset station
group (A to E).
The preset station group letter appears in the front
panel display and changes each time you press the
button.
A/B/C/D/E
CATEGORY
Front panel
or
PRESET/CH
AMP
SOURCE
TV
ENTER
A-E/CAT.
Remote control
59 En
01EN_00_RX-V1700_U.book Page 60 Tuesday, June 27, 2006 9:37 AM
FM/AM TUNING
Exchanging preset stations
3
You can exchange the assignments of two preset stations
with each other. The example below describes the
procedure to exchange preset station “E1” with “A5”.
Select preset station “A5” using A/B/C/D/E
and PRESET/TUNING/CH l / h.
“A5” and the MEMORY indicator flash in the front
panel display.
See “Selecting preset stations” on page 59.
(U.S.A. model)
A/B/C/D/E
PRESET/TUNING/CH
PURE DIRECT
CATEGORY
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
S VIDEO
VIDEO
PHONES
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
VIDEO AUX
ON
OFF
MASTER
A5:FM88.9MHz
MEMORY
3 3 2,4
1
2
Select preset station “E1” using A/B/C/D/E
and PRESET/TUNING/CH l / h.
See “Selecting preset stations” on page 59.
Press and hold EDIT for more than 3
seconds.
“E1” and the MEMORY indicator flash in the front
panel display.
Flashes
4
Flashes
Press EDIT again.
“EDIT E1–A5” appears in the front panel display and
the assignments of the two preset stations are
exchanged.
PRESET/
TUNING
EDIT
SEARCH MODE
PRESET/
TUNING
EDIT
SEARCH MODE
EDIT
E1:FM88.9MHz
Flashes
60 En
MEMORY
Flashes
E1-A5
01EN_00_RX-V1700_U.book Page 61 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
XM SATELLITE RADIO TUNING
XM Satellite Radio is a satellite radio service with millions of listeners across the United States and Canada,
broadcasting live daily. The XM Satellite Radio channel lineup includes over 160 digital channels of choice from coast to
coast: 67 commercial-free music channels, featuring hip hop to opera, classical to country, bluegrass to blues; 33
channels of premier sports, talk, comedy, children’s and entertainment programming; and more than 20 channels of the
traffic and weather information for major metropolitan areas nationwide.
Because XM Satellite Radio is a subscription service, you will need to set up an account and activate service with XM
using your XM Satellite Radio ID number. To check your ID number, follow “Activating XM Satellite Radio” on
page 63. For further information on XM Satellite Radio services, visit the XM Satellite Radio website at
“http://www.xmradio.com/” (for residents in the United States) or “http://www.xmradio.ca/” (for residents in Canada).
This unit is equipped with the Neural Surround decoder (U.S.A. and Canada models only) that plays back the surround
sound content of the XM Satellite Radio broadcasts in multi-channels, resulting in a full surround sound experience.
Notes
Connecting the XM Passport System
Connect XM Passport and XM Passport Home Dock (sold
separately) to the XM jack on the rear panel of this unit.
For details, see the operating instructions provided with
XM Passport System.
XM
(U.S.A. model)
■ Information from XM Satellite Radio Inc.
XM monthly service subscription sold separately. XM
Passport and XM Passport Home Dock required to receive
XM service (sold separately). Installation costs and other
fees and taxes, including a one-time activation fee may
apply. Subscription fee is consumer only. All fees and
programming subject to change. Channels with frequent
explicit language are indicated with an “XL”. Channel
blocking is available for XM radio receivers by calling “1800-XM-RADIO (1-800-967-2346)” (for residents in the
United States) or “1-877-GET-XMSR (1-877-438-9677)”
(for residents in Canada). Subscriptions subject to
Customer Agreement available at “http://
www.xmradio.com/” (for residents in the United States) or
“http://www.xmradio.ca/” (for residents in Canada). XM
service only available in the 48 continuous United States
and Canada. “XM Ready” is a trademark of XM Satellite
Radio Inc. © 2006 XM Satellite Radio Inc. All rights
reserved.
XM Passport and
XM Passport Home Dock
(sold separately)
61 En
BASIC
OPERATION
• The XM Satellite Radio service is only available in the 48
contiguous United States (not available in Alaska and Hawaii)
and Canada.
• XM Passport System and monthly subscription are sold
separately. For details, visit the XM Satellite Radio website at
“http://www.xmradio.com/” (for residents in the United States)
or “http://www.xmradio.ca/” (for residents in Canada).
• For information on obtaining the XM Passport System, visit the
XM Satellite Radio website at
“http://www.xmradio.com/” (for residents in the United States)
or “http://www.xmradio.ca/” (for residents in Canada), or
consult your local retailer that sells XM Ready products.
• To ensure optimal reception of the XM Satellite Radio signals,
the XM Passport System must be placed at or near a southerly
facing window with no obstacles in the path to the sky. You can
mount it indoors or outdoors.
01EN_00_RX-V1700_U.book Page 62 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
XM Satellite Radio controls and functions
Note
The following controls are available only when “XM” is selected as the input source. Rotate the INPUT selector on the front panel (or
set the operation mode selector to SOURCE and then press XM on the remote control) to select “XM” as the input source.
■ Front panel functions
1
■ Remote control functions
2
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
3
4
PRESET/TUNING/CH
PRESET/
TUNING
56
MEMORY
FM/AM
MAN'L/AUTO FM
POWER
POWER
TV
AV
XM
1
POWER
SLEEP
1
PHONO
TUNER
CD
1
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
4
INPUT
DTV
CD
CD-R
2
3
ZONE ON/OFF
STRAIGHT
DTV
DISPLAY
SEARCH MODE
VCR 1
STANDBY
CBL/SAT MD/TAPE PHONO
5
4
VCR 1 DVR/VCR 2
EDIT
CATEGORY
POWER
XM
TUNER
V-AUX/DOCK CBL/SAT
TUNING
MODE
STANDBY
AUDIO SEL
7
6
ENT
DVD
V-AUX/DOCK
9
0
8
9
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
SELECT
OPTICAL
VIDEO AUX
A/B/C/D/E
+
+
+
TV VOL
CH
VOLUME
–
–
–
TV MUTE
TV INPUT
MUTE
SOURCE
(U.S.A. model)
LEVEL
1 INPUT selector
Selects “XM” as the input source.
2 CATEGORY
(All Channel Search mode)
Changes the channel category while staying in the All
Channel Search mode.
(Category Search mode)
Changes the channel category.
(Preset Search mode)
Changes the preset channel group (A to E).
3 PRESET/TUNING/CH l / h
(All Channel Search mode)
Searches for a channel within all channels. Press and hold
for quick search.
(Category Search mode)
Searches for a channel within the selected category. Press
and hold for quick search.
(Preset Search mode)
Changes the preset channel number (1 to 8).
4 SEARCH MODE
Changes the search mode between the All Channel
Search, Category Search, and Preset Search modes
(see page 66).
5 MEMORY (MAN’L/AUTO FM)
Stores a preset channel in the memory (see page 70).
6 DISPLAY
Displays the XM Satellite Radio information such as
channel number, channel name, category, artist name, or
song title displayed in the front panel display or in the
OSD (see page 71).
62 En
VOLUME
PRESET
AMP
PHONES
2
3
SET MENU
TITLE
MENU
BAND
SRCH MODE
PURE DIRECT
AUDIO
ENTER
A-E/CAT.
PARAMETER
STRAIGHT
DISPLAY
RETURN
EFFECT
XM MEMORY
CLASSICAL
4
PRESET/CH
TV
LIVE/CLUB
ENTERTAIN
MOVIE
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
7
8
NIGHT
ENHANCER
9
0
+ 10
ENT
5
6
7
8
7
2
0
A
MUTE
A-E/CAT.
DISPLAY
PRESET/CH
ALL
PRESET
ID1 ID2
CAT.
ZONE 2 ZONE 3
NUMBER
8
B
C
9
REC
DISC SKIP
OFF
ON
MACRO
LEARN
CLEAR
RENAME
(U.S.A. model)
1 XM
Selects “XM” as the input source.
2 PRESET/CH k / n
(All Channel Search mode)
Searches for a channel within all channels. Press and hold
for quick search.
(Category Search mode)
Searches for a channel within the selected category. Press
and hold for quick search.
(Preset Search mode)
Changes the preset channel number (1 to 8).
3 XM MEMORY
Stores a preset channel in the memory (see page 70).
4 Numeric buttons
(All Channel Search or Category Search mode)
Use 1 to 9 and 0 to enter a channel number directly.
(Preset Search mode)
Use 1 to 8 to enter a preset channel number directly.
5 Operation mode selector
Set to SOURCE when you operate the XM Satellite Radio
tuning function.
01EN_00_RX-V1700_U.book Page 63 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
6 SRCH MODE
Changes the search mode between the All Channel
Search, Category Search, and Preset Search modes
(see page 66).
7 A-E/CAT. l / h
(All Channel Search mode)
Changes the channel category.
(Category Search mode)
Changes the channel category.
(Preset Search mode)
Changes the preset channel group (A to E).
8 DISPLAY
Displays the XM Satellite Radio information such as
channel number, channel name, category, artist name, or
song title displayed in the front panel display or in the
OSD (see page 71).
Activating XM Satellite Radio
To sign up for an account with the XM Satellite Radio
service, an XM Satellite Radio ID number is required.
Follow the procedure below to check your ID number, and
then visit the website or call toll-free with a major credit
card handy for signing up.
For residents in the United States
URL: http://activate.xmradio.com/
Toll-free: 1-800-XM-RADIO (1-800-967-2346)
For residents in Canada
URL: https://activate.xmradio.ca/on-line-activation/
activation.jsp
Toll-free: 1-877-GET-XMSR (1-877-438-9677)
BASIC
OPERATION
9 ENT
Confirms an entered channel number in the Direct
Number Access mode (see page 69).
0 ALL
Selects the All Channel Search mode (see page 66).
A NUMBER
Press and hold before you press the input selector or
numeric buttons to switch the function to entering
numbers.
B PRESET
Selects the Preset Search Mode (see page 68).
C CAT.
Selects the Category Search mode (see page 67).
63 En
01EN_00_RX-V1700_U.book Page 64 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
(U.S.A. model)
2
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/
TUNING
PRESET/TUNING/CH
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
Check the XM Satellite Radio reception level
and adjust the orientation of XM Passport
System for a better percentage of the
reception level.
EDIT
CATEGORY
INPUT
DISPLAY
SEARCH MODE
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
y
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
VIDEO
S VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
You can display the XM Satellite Radio reception level by
using the “XM ANTENNA” parameter in “OPTION
MENU” (see page 100).
VIDEO AUX
PHONES
ON
OFF
MASTER
1
3
Notes
• If “CHECK ANTENNA” appears in the front panel
display, XM Passport System may not be connected to the
XM jack on the rear panel of this unit properly. See
“Connecting the XM Passport System” on page 61 and
check the connection.
• The “XM ANTENNA” parameter in “OPTION MENU”
(see page 100) cannot be adjusted by using the remote
control. Instead, you need to adjust the orientation of XM
Passport System connected to the XM jack of this unit for
a better percentage of the reception level.
AMP
+
+
+
TV VOL
CH
VOLUME
1
SOURCE
1
POWER
POWER
TV
AV
XM
PHONO
TUNER
V-AUX/DOCK CBL/SAT
DTV
VCR 1
STANDBY
POWER
AUDIO SEL
SLEEP
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
–
–
–
TV MUTE
TV INPUT
MUTE
PRESET/CH
LEVEL
3
SET MENU
TITLE
MENU
BAND
SRCH MODE
TV
PURE DIRECT
AUDIO
ENTER
A-E/CAT.
PARAMETER
STRAIGHT
DISPLAY
RETURN
EFFECT
XM MEMORY
(U.S.A. model)
1
Rotate the INPUT selector on the front panel
(or set the operation mode selector to
SOURCE and then press XM on the remote
control) to select “XM” as the input source.
The cursor on the left of the XM indicator lights up in
the front panel display.
3
Press PRESET/TUNING/CH l / h on the
front panel (or PRESET/CH k / n on the
remote control) to select channel “0”.
PRESET/CH
PRESET/TUNING/CH
or
INPUT
ENTER
A-E/CAT.
Front panel
Note
Front panel
You cannot select channel “0” if the All Channel Search
mode (see page 66) is not selected.
or
AMP
4
XM
SOURCE
TV
Remote control
64 En
DVR/VCR 2
VCR 1 CBL/SAT
DTV
DVD
MD/TAPE
Check the XM Satellite Radio ID number
displayed in the front panel display and write
it down.
ID:_____________________________________
Lights up
V-AUX
Remote control
CD-R
CD
PHONO
MULTI CH
TUNER XM
01EN_00_RX-V1700_U.book Page 65 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
Basic XM Satellite Radio
operations
1
(U.S.A. model)
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
Rotate the INPUT selector on the front panel
(or set the operation mode selector to
SOURCE and then press XM on the remote
control) to select “XM” as the input source.
The cursor on the left of the XM indicator lights up in
the front panel display and the XM Satellite Radio
information (such as channel number, channel name,
category, artist name, or song title) for the currently
selected channel appears in the front panel display.
MULTI ZONE
EFFECT
SILENT CINEMA
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
S VIDEO
ZONE 2
ZONE 3
L
R
VIDEO
AUDIO
OPTICAL
INPUT
VIDEO AUX
PHONES
ON
OFF
MASTER
INPUT selector
XM button
POWER
POWER
TV
AV
XM
PHONO
TUNER
V-AUX/DOCK CBL/SAT
POWER
SLEEP
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
Front panel
or
AMP
XM
SOURCE
DTV
VCR 1
TV
SELECT
Remote control
AMP
+
+
+
TV VOL
CH
VOLUME
–
–
–
SOURCE
TV
Set to
SOURCE
Lights up
(U.S.A. model)
V-AUX
DVR/VCR 2
VCR 1 CBL/SAT
DTV
DVD
MD/TAPE
CD-R
CD
PHONO
MULTI CH
TUNER XM
[001] Preview
y
When you select “XM” as the input source, this unit
automatically recalls the previously selected channel.
Note
The XM Satellite Radio signals cannot be output at the
AUDIO OUT (REC) jacks.
2
Search for a channel by using one of the XM
Satellite Radio search modes.
• To select a channel from the all channel list, see
“All Channel Search mode” on page 66.
• To select a channel by category, see “Category
Search mode” on page 67.
• To select a channel from the preset channels, see
“Preset Search mode” on page 68.
• To select the desired channel directly by entering
the channel number, see “Direct Number Access
mode” on page 69.
y
• You can use the Neural Surround decoder to enjoy the
surround sound content of XM Satellite Radio broadcasts
in multi-channels (see page 80).
• You can set the XM Satellite Radio preset channels (see
page 70).
• You can display the XM Satellite Radio information in the
front panel display or in the OSD (see page 71).
65 En
BASIC
OPERATION
STANDBY
AUDIO SEL
01EN_00_RX-V1700_U.book Page 66 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
■ All Channel Search mode
2
(U.S.A. model)
Press CATEGORY on the front panel (or
A-E/CAT. l / h on the remote control)
repeatedly to change the channel category.
PURE DIRECT
PRESET/CH
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/
TUNING
PRESET/TUNING/CH
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
A/B/C/D/E
MULTI ZONE
EFFECT
SILENT CINEMA
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
or
OPTICAL
VIDEO AUX
PHONES
ENTER
CATEGORY
ON
OFF
A-E/CAT.
MASTER
2
Front panel
3 1
3
TV MUTE
LEVEL
TV INPUT
PRESET/CH
TITLE
MUTE
SET MENU
PURE DIRECT
MENU
SRCH MODE
BAND
AUDIO
ENTER
A-E/CAT.
PARAMETER
RETURN
XM MEMORY
1
STRAIGHT
2,3
DISPLAY
Remote control
Press PRESET/TUNING/CH l / h on the
front panel (or PRESET/CH k / n on the
remote control) repeatedly to search for a
channel within all channels.
EFFECT
PRESET/CH
(U.S.A. model)
1
Press SEARCH MODE on the front panel (or
SRCH MODE on the remote control)
repeatedly to select “ALL CH SEARCH”.
or
or
SEARCH MODE
Remote control
SET MENU
MENU
SRCH MODE
Front panel
ENTER
A-E/CAT.
Front panel
PRESET/
TUNING
EDIT
Remote control
ALL CH SEARCH
66 En
PRESET/TUNING/CH
y
You can search for a channel quickly by pressing and
holding PRESET/TUNING/CH l / h on the front panel
(or PRESET/CH k / n on the remote control).
01EN_00_RX-V1700_U.book Page 67 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
■ Category Search mode
(U.S.A. model)
2
Press CATEGORY on the front panel (or
A-E/CAT. l / h on the remote control)
repeatedly to change the channel category.
PURE DIRECT
PRESET/CH
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/
TUNING
PRESET/TUNING/CH
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
A/B/C/D/E
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
SILENT CINEMA
OPTIMIZER
MIC
S VIDEO
ZONE 2
ZONE 3
L
R
VIDEO
AUDIO
or
OPTICAL
ENTER
VIDEO AUX
PHONES
CATEGORY
ON
OFF
MASTER
A-E/CAT.
2
Front panel
3 1
3
PRESET/CH
LEVEL
SET MENU
TITLE
MENU
BAND
SRCH MODE
PURE DIRECT
AUDIO
ENTER
A-E/CAT.
PARAMETER
STRAIGHT
1
2,3
DISPLAY
RETURN
XM MEMORY
EFFECT
Remote control
Press PRESET/TUNING/CH l / h on the
front panel (or PRESET/CH k / n on the
remote control) repeatedly to search for a
channel within the selected channel
category.
(U.S.A. model)
PRESET/CH
Press SEARCH MODE on the front panel (or
SRCH MODE on the remote control)
repeatedly to select “CAT SEARCH”.
PRESET/
TUNING
EDIT
SET MENU
or
PRESET/TUNING/CH
or
ENTER
A-E/CAT.
Front panel
Remote control
MENU
SEARCH MODE
Front panel
BASIC
OPERATION
1
SRCH MODE
Remote control
y
You can search for a channel quickly by pressing and
holding PRESET/TUNING/CH l / h on the front panel
(or PRESET/CH k / n on the remote control).
CAT SEARCH
67 En
01EN_00_RX-V1700_U.book Page 68 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
■ Preset Search mode
Prior to selecting a preset channel in the Preset Search
mode, you must preset XM Satellite Radio channels. For
details, see “Setting the XM Satellite Radio preset
channels” on page 70.
2
Press CATEGORY on the front panel (or
A-E/CAT. l / h on the remote control)
repeatedly to change the preset channel
group (A to E).
y
PRESET/CH
The initial factory setting of all preset channels (A1 to E8) is
“[001] Preview”.
A/B/C/D/E
or
(U.S.A. model)
ENTER
CATEGORY
A-E/CAT.
PURE DIRECT
Front panel
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/
TUNING
PRESET/TUNING/CH
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
Remote control
NIGHT
EDIT
INPUT
DISPLAY
SEARCH MODE
CATEGORY
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
SILENT CINEMA
OPTIMIZER
MIC
S VIDEO
ZONE 2
ZONE 3
L
R
VIDEO
AUDIO
3
OPTICAL
VIDEO AUX
PHONES
ON
OFF
MASTER
2
3 1
Press PRESET/TUNING/CH l / h on the
front panel (or PRESET/CH k / n on the
remote control) repeatedly to change the
preset channel number (1 to 8).
PRESET/CH
LEVEL
PRESET/CH
SET MENU
TITLE
MENU
BAND
SRCH MODE
PURE DIRECT
A-E/CAT.
PARAMETER
RETURN
XM MEMORY
PRESET/TUNING/CH
or
AUDIO
ENTER
1
STRAIGHT
2,3
ENTER
A-E/CAT.
DISPLAY
EFFECT
(U.S.A. model)
Front panel
1
Press SEARCH MODE on the front panel (or
SRCH MODE on the remote control)
repeatedly to select “PRESET SEARCH”.
PRESET/
TUNING
SET MENU
EDIT
or
SEARCH MODE
MENU
SRCH MODE
Front panel
Remote control
PRESET SEARCH
68 En
Remote control
y
You can also select the preset channel number directly by
pressing the numeric buttons (1 to 8) on the remote control.
01EN_00_RX-V1700_U.book Page 69 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
■ Direct Number Access mode
LEVEL
PRESET/CH
TITLE
SET MENU
PURE DIRECT
MENU
1
SRCH MODE
BAND
AUDIO
ENTER
A-E/CAT.
PARAMETER
STRAIGHT
DISPLAY
RETURN
EFFECT
XM MEMORY
CLASSICAL
LIVE/CLUB
ENTERTAIN
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
7
8
NIGHT
ENHANCER
9
0
+ 10
ENT
MOVIE
2
Press the numeric buttons on the remote
control to enter the desired three-digit
channel number.
For example, to enter the number 123, press the
numeric buttons as shown below.
2
CLASSICAL
LIVE/CLUB
ENTERTAIN
1
2
3
(U.S.A. model)
1
The display changes as follows.
Press SRCH MODE on the remote control
repeatedly to select “ALL CH SEARCH” or
“CAT SEARCH”.
<XM> --1
SET MENU
MENU
SRCH MODE
Remote control
BASIC
OPERATION
<XM> -12
ALL CH SEARCH
or
<XM>123
CAT SEARCH
y
• To enter a one-digit or two-digit channel number, press the
numeric buttons on the remote control and then press ENT
to confirm the input number.
• Instead of pressing ENT to tune into the channel
immediately, you can wait a few seconds until this unit
confirms the entered channel number.
• If no button is pressed within a few seconds after you enter
a one-digit or two-digit number, this unit automatically
confirms the entered channel number.
• Pressing a button other than the numeric buttons or ENT
cancels the Direct Number Access mode procedure.
69 En
01EN_00_RX-V1700_U.book Page 70 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
Setting the XM Satellite Radio
preset channels
2
You can use this feature to store up to 40 XM Satellite
Radio channels (A1 to E8: 8 preset channel numbers in
each of the 5 preset channel groups). You can then recall
any preset channel easily by selecting the preset channel
group and number as described in “Preset Search mode”
on page 68.
Press MEMORY on the front panel (or XM
MEMORY on the remote control).
The MEMORY indicator flashes in the front panel
display for approximately 5 seconds.
MEMORY
MAN'L/AUTO FM
or
Front panel
RETURN
XM MEMORY
Remote control
(U.S.A. model)
PURE DIRECT
MEMORY
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
MEMORY
PRESET/
TUNING
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
Flashes
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
SILENT CINEMA
OPTIMIZER
MIC
S VIDEO
PHONES
ZONE 2
ZONE 3
L
R
VIDEO
AUDIO
OPTICAL
VIDEO AUX
ON
Note
OFF
MASTER
3 4
TV MUTE
LEVEL
3,4
2,5
TV INPUT
PRESET/CH
2,5
MUTE
SET MENU
TITLE
MENU
BAND
SRCH MODE
PURE DIRECT
AUDIO
ENTER
A-E/CAT.
PARAMETER
RETURN
XM MEMORY
STRAIGHT
DISPLAY
EFFECT
(U.S.A. model)
1
You must proceed to and carry out steps 3 through 5 while
the MEMORY indicator is flashing in the front panel
display.
Search for a channel you want to set as a
preset channel by using one of the XM
Satellite Radio search modes.
See “Basic XM Satellite Radio operations” on
page 65 for details.
3
Press CATEGORY on the front panel (or
A-E/CAT. l / h on the remote control)
repeatedly to select a preset channel group
(A to E) while the MEMORY indicator is
flashing.
The preset channel group letter appears in the front
panel display.
PRESET/CH
A/B/C/D/E
or
CATEGORY
ENTER
A-E/CAT.
[043] XMU
Front panel
Remote control
Currently selected channel number
C
[043] XMU
Currently selected preset channel group
70 En
MEMORY
Flashes
01EN_00_RX-V1700_U.book Page 71 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
4
Press PRESET/TUNING/CH l / h on the
front panel (or PRESET/CH k / n on the
remote control) repeatedly to select a preset
channel number (1 to 8) while the MEMORY
indicator is flashing.
The preset channel number appears in the front panel
display.
Displaying the XM Satellite Radio
information
You can display the XM Satellite Radio information (such
as channel number, channel name, category, artist name,
or song title) for the currently selected channel in the front
panel display or in the OSD.
(U.S.A. model)
PRESET/CH
PURE DIRECT
PRESET/TUNING/CH
or
ENTER
VOLUME
AUDIO
SELECT
TONE
CONTROL
A-E/CAT.
A/B/C/D/E
PRESET/
TUNING
PRESET/TUNING/CH
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
SILENT CINEMA
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
VIDEO AUX
PHONES
ON
OFF
Front panel
Remote control
MASTER
DISPLAY
C5
[043] XMU
MEMORY
PRESET/CH
SET MENU
TITLE
MENU
BAND
SRCH MODE
PURE DIRECT
AUDIO
ENTER
A-E/CAT.
PARAMETER
Flashes
Currently selected preset channel number
RETURN
XM MEMORY
BASIC
OPERATION
LEVEL
STRAIGHT
DISPLAY
DISPLAY
EFFECT
(U.S.A. model)
5
Press MEMORY on the front panel (or XM
MEMORY on the remote control) to set the
selected XM Satellite Radio channel as a
preset channel while the MEMORY indicator
is flashing.
A colon (:) appears next to the preset channel number
for confirmation, and the MEMORY indicator turns
off in the front panel display.
MEMORY
MAN'L/AUTO FM
or
Front panel
RETURN
XM MEMORY
Remote control
Note
If a status message or an error message appears in the front panel
display or in the OSD, see the “XM Satellite Radio (U.S.A. and
Canada models only)” section in “TROUBLESHOOTING” on
page 122 for appropriate remedies.
■ Displaying the XM Satellite Radio
information in the front panel display
Press DISPLAY on the front panel or on the
remote control repeatedly to toggle between the
following XM Satellite Radio information display
modes.
TUNING
MODE
Channel number / name
DISPLAY
C5: [043] XMU
Front panel
or
Channel category
PARAMETER
Colon (:)
DISPLAY
Artist name / Song title
Note
Remote control
Once you set a new preset channel, the one previously
stored in the same preset channel group and number is
cleared.
71 En
01EN_00_RX-V1700_U.book Page 72 Tuesday, June 27, 2006 9:37 AM
XM SATELLITE RADIO TUNING
When the channel number / name is displayed:
[043] XMU
■ Displaying the XM Satellite Radio
information in the OSD
Press DISPLAY on the remote control.
The following screen is displayed in the OSD.
TUNING
MODE
When the channel category is displayed:
PARAMETER
or
DISPLAY
DISPLAY
Front panel
Remote control
<CAT>Rock
XM INFORMATION
When the artist name / song title is displayed:
Coldplay / Spe
p
y
• The front panel display can indicate up to 14 alphanumeric
characters at once. You can set whether to display the XM
Satellite Radio information in the front panel display in a
continuous manner or by 14 alphanumeric characters at once by
using the “FL SCROLL” parameter in “OPTION MENU” (see
page 98).
• If the XM Satellite Radio information contains a character that
cannot be recognized by this unit, the character will be
displayed with a space.
Note
If you press DISPLAY while the XM Satellite Radio information
display is scrolling from right to left in the front panel display, the
XM Satellite Radio information display mode toggles as
described above.
72 En
p
ALL CH SEARCH
XM
:043
CHAN :XMU
CAT
:Rock
NAME :Coldplay
TITLE :Speed of sound
.( Coldplay / Spe )
[]/[]:CHANNEL
[p]/[[]:CATEGORY
y
• To turn off the OSD, press DISPLAY on the front panel (or on
the remote control).
• You can select the amount of time the XM Satellite Radio
information is displayed in the OSD by using the “ON
SCREEN” parameter in “OPTION MENU” (see page 98).
• To hold the XM Satellite Radio information screen, press
ENTER on the remote control while it is being displayed in the
OSD.
• The XM Satellite Radio information screen on hold is released
if you press ENTER on the remote control again or if you
change the XM Satellite Radio channel.
• This unit can save up to two XM Satellite Radio information
screens for future reference. To view the previous two XM
Satellite Radio information screens, press TITLE on the remote
control repeatedly while the current XM Satellite Radio
information screen is being hold.
01EN_00_RX-V1700_U.book Page 73 Tuesday, June 27, 2006 9:37 AM
USING IPOD
USING iPod
Once you have stationed your iPod in a YAMAHA iPod universal dock (such as the YDS-10, sold separately) connected
to the DOCK terminal of this unit (see page 27), you can enjoy playback of your iPod using the supplied remote control.
You can also use the Compressed Music Enhancer mode of this unit to improve the sound quality of the compression
artifacts (such as the MP3 format) stored on your iPod (see page 52).
Notes
• Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.
• Some features may not be compatible depending on the model or the software version of your iPod.
y
Controlling iPod
You can control your iPod when “V-AUX” is selected as
the input source. The operations of your iPod can be done
with the aid of the OSD of this unit (menu browse mode)
or without it (simple remote mode).
■ Controlling iPod in the simple remote
mode
You can perform the basic operations of your iPod (play,
stop, skip, etc.) using the supplied remote control without
the aid of the OSD of this unit.
y
• You can view the photos or video clips stored on your iPod.
• Operations can be also done with the controls on your iPod.
■ Controlling iPod in the menu browse
mode
You can perform the advanced operations of your iPod
using the supplied remote control with the aid of the OSD
of this unit. The name of the song being played appears in
the front panel display according to the “FL SCROLL”
parameter in “OPTION MENU” (see page 98). You can
also browse the songs stored on your iPod in the OSD.
Further, you can change or adjust settings for your iPod to
suit your personal preferences.
Notes
• Operations cannot be done with the controls on your iPod.
• The YAMAHA logo appears in the display window of your
iPod.
• There are some characters that cannot be displayed in the front
panel display or in the OSD of this unit. Those characters are
replaced with underscores “_”.
• The “Settings” parameters can be changed or adjusted only in
the OSD. Press ENTER on the remote control to toggle between
the “Settings” parameter settings.
• You cannot browse the photos or video clips stored on your
iPod in the OSD. Instead, you must use the controls on your
iPod to select the desired photos or video clips.
73 En
BASIC
OPERATION
• For a complete list of the remote control functions used to control your iPod, see the “iPod” column in “Controlling other
components” on page 102.
• For a complete list of status messages that appear in the front panel display and in the OSD, see the “iPod” section in
“TROUBLESHOOTING” on page 128.
• Once your iPod is stationed in a YAMAHA iPod universal dock (such as the YDS-10, sold separately) connected to the DOCK
terminal of this unit, this unit begins signal transmission with your iPod.
• Once the connection between your iPod and this unit is complete, “iPod connected” appears in the front panel display and the DOCK
indicator lights up in the front panel display.
• Only the analog audio and video signals of your iPod are input at the DOCK terminal, and the analog audio signals can be output at the
analog AUDIO OUT (REC) jacks for recording.
• Your iPod battery is automatically charged when your iPod is stationed in a YAMAHA iPod universal dock (such as the YDS-10, sold
separately) connected to the DOCK terminal of this unit as long as this unit is turned on. You can also select whether this unit charges
the battery of the stationed iPod or not when this unit is in the standby mode by selecting the “STANDBY CHRG” parameter in
“OPTION MENU” (on page 100).
• While the stationed iPod is being charged in the standby mode of this unit, the battery charge indicator (see page 10) appears in the
front panel display. Once the charge is complete (or after 4 hours from the start of the charge), the indicator disappears.
01EN_00_RX-V1700_U.book Page 74 Tuesday, June 27, 2006 9:37 AM
USING iPod
1
Set the operation mode selector to SOURCE
and then press DISPLAY on the remote
control.
The following display appears in the OSD.
AMP
PARAMETER
SOURCE
DISPLAY
TV
Shuffle Shuffle
Use this feature to set this unit to play songs or albums in
random order.
Choices: Off, Songs, Albums
• Select “Off ” to deactivate this feature.
• Select “Songs” to set this unit to play songs in random
order.
• Select “Albums” to set this unit to play albums in
random order.
Note
iPod
Top
Playlists
Artists
Albums
Songs
Genres
Composers
Settings
2
When “Shuffle” is set to a setting other than “Off ”, “
” appears
in the top right corner while songs or albums are being shuffled.
>
>
>
>
>
>
>
Press k / n / l / h on the remote control to
navigate the iPod menu and then press
ENTER to begin playback of the selected
song.
PRESET/CH
PRESET/CH
Repeat Repeat
Use this feature to set this unit to repeat one song or a
sequence of songs.
Choices: Off, One, All
• Select “Off ” to deactivate this feature.
• Select “One” to set this unit to repeat one song.
• Select “All” to set this unit to repeat a sequence of
songs.
Note
When “Repeat” is set to a setting other than “Off ”, “ ” or “ ”
appears in the top right corner while one song or a sequence of
songs are being repeated.
1
ENTER
ENTER
A-E/CAT.
A-E/CAT.
Choices: Playlists (playlists), Artists (artists),
Albums (albums), Songs (songs),
Genres (genres), Composers (composers),
Settings (settings)
• Playlists > Songs
• Artists > Albums > Songs
• Albums > Songs
• Songs
• Genres > Artists > Albums > Songs
• Composers > Albums > Songs
• Settings > Shuffle, Repeat
74 En
All
01EN_00_RX-V1700_U.book Page 75 Tuesday, June 27, 2006 9:37 AM
RECORDING
RECORDING
Recording adjustments and other operations are performed from the recording components. Refer to the operating
instructions for those components.
CAUTION
The DTS signal is a digital bitstream. Attempting to digitally record the DTS bitstream will result in
noise being recorded. Therefore, if you want to use this unit to record sources encoded in DTS, the
following considerations and adjustments need to be made. To play DTS-encoded DVDs and CDs
(when using a digital audio connection) on your DTS-compatible player, follow its operating
instructions to make a setting so that the analog signal will be output from the player.
Notes
y
Do a test recording before you start an actual recording.
If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture
itself may be disturbed due to those signals.
(U.S.A. model)
2
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
Rotate the INPUT selector on the front panel
(or press one of the input selector buttons on
the remote control) to select the source
component you want to record from.
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
S VIDEO
VIDEO
ZONE 2
ZONE 3
L
R
AUDIO
OPTICAL
INPUT
VIDEO AUX
PHONES
ON
OFF
MASTER
PHONO
or
2
DTV
POWER
POWER
TV
AV
XM
PHONO
2
TUNER
V-AUX/DOCK CBL/SAT
DTV
VCR 1
STANDBY
POWER
AUDIO SEL
SLEEP
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
Front panel
Turn on all the connected components.
VCR 1
CD
MD/TAPE
CD-R
DVR/VCR 2
DVD
Remote control
3
Start playback on the selected source
component or select a broadcast station.
4
Start recording on the recording component.
(U.S.A. model)
1
TUNER
V-AUX/DOCK CBL/SAT
75 En
BASIC
OPERATION
• When this unit is set to the standby mode, you cannot record between other components connected to this unit.
• The settings of TONE CONTROL (see page 50), VOLUME, the speaker level (see page 90) and the sound field programs (see
page 45) do not affect recorded material.
• The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded.
• The XM Satellite Radio signals (U.S.A. and Canada models only) cannot be output at the AUDIO OUT (REC) jacks.
• Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Likewise,
analog signals input at the AUDIO IN jacks are not output at the DIGITAL OUTPUT jack. Therefore, if your source component is
connected to provide only digital or analog signals, you can only record digital or analog signals.
• A given input source is not output on the same OUT (REC) channel.
• S-video and composite video signals pass independently through the video circuits of this unit. Therefore, when recording or dubbing
video signals input from a video source component that provides only an S-video or a composite video signal, you can record only an
S-video or a composite video signal on your VCR.
• The analog audio signals input at the DOCK terminal can be output at the analog AUDIO OUT (REC) jacks for recording.
• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright
laws.
01EN_00_RX-V1700_U.book Page 76 Tuesday, June 27, 2006 9:37 AM
ADVANCED SOUND CONFIGURATIONS
ADVANCED SOUND CONFIGURATIONS
Changing sound field parameter
settings
3
You can enjoy good quality sound with the initial factory
settings. Although you do not have to change the initial
factory settings, you can change some of the parameters to
better suit the input source or your listening room.
Press one of the sound field program
selector buttons repeatedly to select the
desired sound field program you want to
adjust.
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
1
2
3
4
STEREO
5
Note
You cannot change the sound field parameter values when
“MEMORY GUARD” in “OPTION MENU” is set to “ON” (see
page 98). If you want to change the sound field parameter values,
set “MEMORY GUARD” to “OFF”.
4
AMP
+
+
+
TV VOL
CH
VOLUME
–
–
–
SOURCE
TV MUTE
TV INPUT
4
SET MENU
PURE DIRECT
TITLE
MENU
BAND
SRCH MODE
AUDIO
ENTER
A-E/CAT.
PARAMETER
STRAIGHT
DISPLAY
RETURN
2,5
PRESET/CH
PRESET/CH
EFFECT
XM MEMORY
CLASSICAL
3
2
MUTE
PRESET/CH
LEVEL
TV
Press k / n to select the desired sound field
parameter and then l / h to change the
selected sound field parameter value.
• Press h to increase the value.
• Press l to decrease the value.
LIVE/CLUB
ENTERTAIN
MOVIE
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
7
8
NIGHT
ENHANCER
9
0
+ 10
ENT
ENTER
ENTER
A-E/CAT.
A-E/CAT.
(U.S.A. model)
1
Turn on the video monitor connected to this
unit.
2
Set the operation mode selector to AMP and
then press PARAMETER on the remote
control.
The following display is shown in the OSD.
AMP
PARAMETER
SOURCE
DISPLAY
TV
Sound field program category
MOVIE
y
• For details about the function and control range of each sound
field parameter, see page 77.
• When you set a sound field parameter to a value other than the
initial factory settings, an asterisk mark (*) appears by the
sound field parameter name in the OSD.
• Repeat steps 3 and 4 as necessary to change other sound field
program parameter settings.
• The available sound field parameters for some of the sound field
programs may be displayed on more than one page in the OSD.
In this case, press k / n to scroll through pages.
• If you press and hold l / h to change the sound field
parameter value, the initial factory settings are shown
momentarily in the front panel display.
• Use the “PARAM. INI” feature in “OPTION MENU” to
initialize the parameters of each sound field program within a
sound field program group (see page 99).
• To initialize the parameters of the selected sound field program,
press n repeatedly to select “PARAM. INIT” and then press h
repeatedly.
Sci-fi
Cursor
. < P R O L O G I C >
DSPLEVEL;;;+0dB
P.INIT.DLY;;16ms
P.ROOM SIZE;;1.0
S.INIT.DLY;;16ms
5
Press PARAMETER to turn off the sound field
parameter display.
PARAMETER
DISPLAY
Sound field parameters
76 En
Sound field parameter
values
01EN_00_RX-V1700_U.book Page 77 Tuesday, June 27, 2006 9:37 AM
ADVANCED SOUND CONFIGURATIONS
■ Sound field parameter descriptions
You can adjust the values of certain digital sound field parameters so that the sound fields are recreated accurately in your
listening room. Not all of the following parameters are found in every program.
y
To change sound field parameter settings to suit your listening environment, see page 76 for details.
Sound field parameter
DSP LEVEL
Features
DSP level. Adjusts the level of all the DSP effect sounds within a narrow range. Depending on
the acoustics of your listening room, you may want to increase or decrease the DSP effect level
relative to the level of the direct sound.
Control range: –6 dB to +3 dB
Initial delay. Presence, surround, and surround back initial delay. Changes the apparent distance
from the source sound by adjusting the delay between the direct sound and the first reflection
heard by the listener. The smaller the value, the closer the sound source seems to the listener. The
larger the value, the farther it seems. For a small room, set to a small value. For a large room, set
to a large value.
Control range: 1 to 99 ms (INIT.DLY and P.INIT.DLY)
1 to 49 ms (S.INIT.DLY and SB INI.DLY)
Source sound
Level
Level
Early
reflections
Level
INIT.DLY
P.INIT.DLY
S.INIT.DLY
SB INI.DLY
Time
Time
Time
Delay
Delay
Delay
Sound source
ADVANCED
OPERATION
Reflection face
Small value = 1 ms
Large value = 99 ms
77 En
01EN_00_RX-V1700_U.book Page 78 Tuesday, June 27, 2006 9:37 AM
ADVANCED SOUND CONFIGURATIONS
Sound field parameter
ROOM SIZE
P.ROOM SIZE
S.ROOM SIZE
SB ROOM SIZE
Features
Room size. Presence, surround, and surround back room size. Adjusts the apparent size of the
surround sound field. The larger the value, the larger the surround sound field becomes. As the
sound is repeatedly reflected around a room, the larger the hall is, the longer the time between
the original reflected sound and the subsequent reflections. By controlling the time between the
reflected sounds, you can change the apparent size of the virtual venue. Changing this parameter
from one to two doubles the apparent length of the room.
Control range: 0.1 to 2.0
Time
Early
reflections
Level
Level
Level
Source sound
Time
Time
Sound source
Small value = 0.1
LIVENESS
S.LIVENESS
SB LIVENESS
Large value = 2.0
Liveness. Surround and surround back liveness. Adjusts the reflectivity of the virtual walls in the
hall by changing the rate at which the early reflections decay. The early reflections of a sound
source decay much faster in a room with acoustically absorbent wall surfaces than in one which
has highly reflective surfaces. A room with acoustically absorbent surfaces is referred to as
“dead”, while a room with highly reflective surfaces is referred to as “live”. This parameter lets
you adjust the early reflection decay rate and thus the “liveness” of the room.
Control range: 0 to 10
Source sound
Time
Small reflected
sound
Small value = 0
78 En
Level
Dead
Level
Level
Live
Time
Time
Large reflected
sound
Large value = 10
01EN_00_RX-V1700_U.book Page 79 Tuesday, June 27, 2006 9:37 AM
ADVANCED SOUND CONFIGURATIONS
Sound field parameter
REV.TIME
Features
Reverberation time. Adjusts the amount of time taken for the dense, subsequent reverberation
sound to decay by 60 dB at 1 kHz. This changes the apparent size of the acoustic environment
over an extremely wide range. Set a longer reverberation time for “dead” sources and listening
room environments, and a shorter time for “live” sources and listening room environments.
Control range: 1.0 to 5.0 s
Source sound
Reverberation
Reverberation
Early reflections
60 dB
60 dB
REV.TIME
Sound source
REV.TIME
Short
reverberation
REV.TIME
Long
reverberation
Small value = 1.0 s
REV.DELAY
60 dB
Large value = 5.0 s
Reverberation delay. Adjusts the time difference between the beginning of the direct sound and
the beginning of the reverberation sound. The larger the value, the later the reverberation sound
begins. A later reverberation sound makes you feel as if you are in a larger acoustic environment.
ADVANCED
OPERATION
Level
Control range: 0 to 250 ms
Source sound
(dB)
60 dB
Reverberation
Time
REV.DELAY
Reverberation level. Adjusts the volume of the reverberation sound. The larger the value, the
stronger the reverberation becomes.
Control range: 0 to 100%
Level
REV.LEVEL
REV.TIME
Source sound
REV. LEVEL
Time
79 En
01EN_00_RX-V1700_U.book Page 80 Tuesday, June 27, 2006 9:37 AM
ADVANCED SOUND CONFIGURATIONS
Sound field parameter
DIALG.LIFT
Features
Dialog lift. Adjusts the height of the front and center channel sounds by assigning some of the
front and center channel elements to the presence speakers. The larger the parameter, the higher
the position of the front and center channel sound.
Choices: 0, 1, 2, 3, 4, 5
2ch Stereo
DIRECT
2-channel stereo direct. Bypasses the decoders and DSP processors of this unit for pure hi-fi stereo
sound when playing 2-channel analog sources.
Choices: AUTO, OFF
y
• Select “AUTO” to bypass the decoders, DSP processors and the tone control circuitry only
when “BASS” and “TREBLE” are set to 0 dB (see page 50).
• Select “OFF” not to bypass the decoders, DSP processors and the tone control circuitry when
“BASS” and “TREBLE” are set to 0 dB.
• When multi-channel signals (Dolby Digital and DTS) are input, they are downmixed to 2
channels and output from the front left and right speakers.
• The low-frequency signals input from the front left and right speakers are redirected to the
subwoofer in the following cases:
– “LFE/BASS OUT” is set to “BOTH” (see page 87).
– “FRONT SP” is set to “SMALL” (see page 88) and “LFE/BASS OUT” is set to “SWFR”
(see page 87).
7ch Stereo
CT LEVEL
SL LEVEL
SR LEVEL
SB LEVEL
PL LEVEL
PR LEVEL
7-channel stereo center, surround left, surround right, surround back, presence left and presence right
levels. Adjusts the volume level of each channel in the 7-channel stereo mode.
Control range: 0 to 100%
Selecting decoders
2
■ Selecting decoders for 2-channel
sources (surround decode mode)
Use this feature to play back sources with selected
decoders. You can play back 2-channel sources on multichannels.
1
Set the operation mode selector to AMP and
then press SUR. DECODE on the remote
control to select the surround decode mode.
AMP
SOURCE
TV
80 En
SUR. DECODE
6
Press SELECT on the remote control
repeatedly to select the desired decoder.
You can select from the following modes depending
on the type of source you are playing and your
personal preference.
SELECT
7
y
• You can select the desired decoder by pressing SELECT
and then press l / h repeatedly on the remote control.
• You can change the decoder parameter settings. Press
PARAMETER and then k / n repeatedly on the remote
control to select the desired decoder parameter. You can
change the value of the selected parameter by pressing
l / h repeatedly on the remote control.
01EN_00_RX-V1700_U.book Page 81 Tuesday, June 27, 2006 9:37 AM
ADVANCED SOUND CONFIGURATIONS
■ Decoder descriptions
Remote control
button
Category of the
program
SUR.DECODE
6
SURROUND DECODE
Name of the
program
PLIIxMusic
PLIIMusic
Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for music sources. The Pro Logic IIx decoder is not
available when “SB L/R SP” is set to “NONE” (see page 89).
PANORAMA
DIMENSION
CENTER WIDTH
Program description
Available sound field parameters (see page 77)
SUR.DECODE
6
SURROUND DECODE
PRO LOGIC
Dolby Pro Logic processing for any sources.
SUR.DECODE
6
SURROUND DECODE
PLIIx Movie
PL II Movie
Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for movie sources. The Pro Logic IIx decoder is not available when “SB L/R SP”
is set to “NONE” (see page 89).
SUR.DECODE
6
SURROUND DECODE
PLIIx Music
PL II Music
Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for music sources. The Pro Logic IIx decoder is not available when “SB L/R SP”
PANORAMA
SUR.DECODE
6
DIMENSION
SURROUND DECODE
ADVANCED
OPERATION
is set to “NONE” (see page 89).
CENTER WIDTH
PLIIx Game
PL II Game
Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for game sources. The Pro Logic IIx decoder is not available when “SB L/R SP”
is set to “NONE” (see page 89).
SUR.DECODE
6
SURROUND DECODE
Neo: 6 Cinema
DTS processing for movie sources.
SUR.DECODE
6
SURROUND DECODE
Neo:6 Music
DTS processing for music sources.
C. IMAGE
SUR.DECODE
6
neural sur.
SURROUND DECODE
(U.S.A. and Canada
models only)
Neural Surround processing for any sources.
The Neural Surround decoder is compatible with PCM signals (32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz and 96 kHz) and analog 2channel input sources. When Neural Surround-incompatible signals are being input while the Neural Surround decoder is selected, multichannel sources are decoded straight into the appropriate channels without any additional effect processing and the Neural Surroundincompatible PCM signals are played back in stereo. The Neural Surround decoder is especially suitable for the XM HD Surround program of
XM Satellite Radio.
y
When you select the surround decode mode for Dolby Digital, DTS or DTS 96/24 sources, this unit automatically selects “SURROUND
DECODE Dolby Digital”, “SURROUND DECODE DTS” or “SURROUND DECODE DTS 96/24” program.
81 En
01EN_00_RX-V1700_U.book Page 82 Tuesday, June 27, 2006 9:37 AM
ADVANCED SOUND CONFIGURATIONS
Decoder parameter descriptions
Decoder parameter
Features
PRO LOGIC IIx Music
PRO LOGIC II Music
PANORAMA
Pro Logic IIx Music and Pro Logic II Music panorama. Sends stereo signals to the surround speakers as
well as the front speakers for a wraparound effect.
PRO LOGIC IIx Music
PRO LOGIC II Music
DIMENSION
Pro Logic IIx Music and Pro Logic II Music dimension. Adjusts the sound field either towards the front
or towards the rear.
Choices: OFF, ON
Control range: –3 (towards the rear) to +3 (towards the front)
Initial setting: STD (standard)
PRO LOGIC IIx Music
PRO LOGIC II Music
CENTER WIDTH
Pro Logic IIx Music and Pro Logic II Music center width. Moves the center channel output completely
towards the center speaker or towards the front left and right speakers. A larger value moves the center
channel output towards the front left and right speakers.
Control range: 0 (center channel sound is output only from the center speaker) to
7 (center channel sound is output only from the front left and right speakers)
Initial setting: 3
DTS Neo:6 Music
C.IMAGE
DTS Neo:6 Music center image. Adjusts the front left and right channel output relative to the center
channel to make the center channel more or less dominant as necessary.
Control range: 0.0 to 1.0
Initial setting: 0.3
■ Selecting decoders used with sound
field programs
Use this feature to select the desired decoder used with
MOVIE sound field programs (except “Mono Movie”).
See page 47 for details about MOVIE sound field
program.
1
Set the operation mode selector to AMP and
then press MOVIE on the remote control
repeatedly to select the desired MOVIE
sound field programs.
AMP
MOVIE
SOURCE
4
TV
2
Press SELECT repeatedly to select the
desired decoder used with the selected
sound field program.
You can select from the following decoders
depending on the type of source you are playing and
your personal preference.
y
You can select the desired decoder by pressing SELECT and
then press l / h repeatedly on the remote control.
82 En
Available decoders
Decoder
PRO LOGIC
PLIIx Movie
PLII Movie
Neo:6 Cinema
Functions
Dolby Pro Logic processing for
any sources
Dolby Pro Logic IIx (or Dolby
Pro Logic II) processing for
movie sources. The Pro Logic IIx
decoder is not available when “SB
L/R SP” is set to “NONE” (see
page 89).
DTS processing for movie
sources
01EN_00_RX-V1700_U.book Page 83 Tuesday, June 27, 2006 9:37 AM
ADVANCED SOUND CONFIGURATIONS
■ Selecting decoders for multi-channel
sources
If you connected surround back speakers, use this feature
to enjoy 6.1/7.1-channel playback for multi-channel
sources using the Dolby Pro Logic IIx, Dolby Digital EX
or DTS-ES decoders.
1
Set the operation mode selector to AMP and
then press EXTD SUR. on the remote control
repeatedly to switch between 5.1 and 6.1/7.1channel playback.
AMP
EXTD SUR.
SOURCE
8
TV
2
Press l / h repeatedly to select a decoder
while the name of the decoder is displayed.
PRESET/CH
ENTER
Decoders
You can select from the following decoders depending on
the format of the source you are playing.
Decoder
Functions
PLIIxMovie
q D+PLIIx Movie
DTS+PLIIx Movie
MPCM+PLIIx Movie
DSD+PLIIx Movie
Plays back multi-channel
sources in 7.1 channels using
the Pro Logic IIx movie
decoder.
PLIIxMusic
q D+PLIIx Music
DTS+PLIIx Music
MPCM+PLIIx Music
DSD+PLIIx Music
Plays back multi-channel
sources in 6.1/7.1 channels
using the Pro Logic IIx music
decoder.
DTS ES
DTS 96/24 ES
Plays back DTS signals in 6.1/
7.1 channels using the DTS-ES
decoder.
DOLBY D EX
DTS+DOLBY EX
MPCM+DOLBY EX
DSD+DOLBY EX
Plays back multi-channel
sources in 6.1/7.1 channels
using the Dolby Digital EX
decoder.
A-E/CAT.
Notes
• “PLIIx Movie” is available only when “SB L/R SP” (see
page 89) is set to “SMLx2” or “LRGx2”.
• Some 6.1/7.1-channel compatible discs do not have a signal flag
that can be automatically detected by this unit. When playing
these kinds of discs in 6.1/7.1 channels, select a decoder
manually from “PLIIx Music”, “EX/ES” or “EX”.
• 6.1/7.1-channel playback is not possible even if you press
EXTD SUR. in the following cases:
– when “SUR. L/R SP” (see page 88) or “SB L/R SP” (see
page 89) is set to “NONE”.
– when the component connected to the MULTI CH INPUT
jacks is being played.
– when the source being played does not contain surround left
and right channel signals.
– when a Dolby Digital KARAOKE source is being played.
– when the “2ch Stereo” (see page 51) or Pure Direct (see
page 50) mode is selected.
• When this unit is turned off, this setting will be reset to
“AUTO”.
• The Pro Logic IIx decoder is not available when “SUR. B L/R
SP” is set to “NONE” (see page 89).
83 En
ADVANCED
OPERATION
Auto AUTO
When a signal flag that can be recognized by this unit is
input, this unit selects the optimum decoder to play back
the signal in 6.1/7.1 channels.
If this unit cannot recognize the flag or no flag is present
in the input signal, it cannot automatically be played in
6.1/7.1 channels.
Off OFF
Decoders are not used to create 6.1/7.1 channels.
01EN_00_RX-V1700_U.book Page 84 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
CUSTOMIZING THIS UNIT (MANUAL SETUP)
You can use the following parameters in “SET MENU” to adjust a variety of system settings and customize the way this
unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening
environment.
■ Auto setup AUTO SETUP
Use this feature to automatically adjust speaker and system parameters (see page 32).
■ Manual setup MANUAL SETUP
Use this feature to manually adjust speaker and system parameters.
Basic menu 1 BASIC MENU
Use this menu to manually adjust basic system parameters.
Parameter
Features
Page
A)SPEAKER SET
Selects the size of each speaker, the speakers for low-frequency signal output, and the
crossover frequency.
87
B)SP LEVEL
Adjusts the output level of each speaker.
90
C)SP DISTANCE
Adjusts the delay time of each speaker.
90
D)TEST TONE
Turns the test tone output on or off for the SPEAKER SET, SPEAKER LEVEL and SP
DISTANCE setting.
91
Sound menu 2 SOUND MENU
Use this menu to manually adjust any speaker settings, alter the quality and tone of the sound output by the system or
compensate for video signal processing delays when using LCD monitors or projectors.
Parameter
Features
Page
A)EQUALIZER
Adjusts the tonal quality of the center speaker.
91
B)LFE LEVEL
Adjusts the output level of the LFE channel for Dolby Digital or DTS signals.
92
C)DYNAMIC RANGE
Adjusts the dynamic range of Dolby Digital or DTS signals.
92
D)AUDIO SET
Adjusts the muting level, audio delay and tone bypass settings.
93
E)HDMI SET
Selects the component to play back HDMI audio signals.
93
84 En
01EN_00_RX-V1700_U.book Page 85 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
Input menu 3 INPUT MENU
Use this menu to manually reassign the input/output jacks, select the input mode or rename the input source.
Parameter
Features
Page
A)I/O ASSIGNMENT
Assigns the input/output jacks of this unit according to the component to be used.
94
B)INPUT RENAME
Changes the name of the input source.
95
C)VOLUME TRIM
Adjusts the output volume of each jack.
96
D)DECODER MODE
Selects the input mode for the sources connected to the DIGITAL INPUT jacks on the rear
panel of this unit.
96
E)MULTI CH SET
Adjusts the direction of the signals input into the center, subwoofer, and surround channels
when a source component is connected to the MULTI CH INPUT jacks.
96
Option menu 4 OPTION MENU
Use this menu to manually adjust the optional system parameters.
Parameter
Features
Page
Adjusts the brightness of the display and converts video signals.
97
B)MEMORY GUARD
Locks sound field program parameters and other “SET MENU” settings.
98
C)AUDIO SELECT
Initializes the parameters of a group of sound field programs.
99
D)DECODER MODE
Selects whether to initialize the settings or to recall the previous settings for the input mode
selected in INPUT MENU.
99
E)PARAM.INI
Initializes the parameters of a group of sound field programs.
99
F)ZONE SET
Adjusts the Zone 2 and Zone 3 parameters.
99
G)XM RADIO SET
Displays the current reception level of XM Passport System.
100
H)DOCK SET
Selects whether this unit charges the battery of the connected iPod or not when this unit is in
the standby mode.
100
Note
The “XM RADIO SET” parameter is only applicable to the U.S.A. and Canada models.
■ Signal information SIGNAL INFO
Use this feature to check audio signal information (see page 42).
85 En
ADVANCED
OPERATION
A)DISPLAY SET
01EN_00_RX-V1700_U.book Page 86 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
Using SET MENU
2
Press k / n to select “MANUAL SETUP”.
Use the remote control to access and adjust each
parameter.
PRESET/CH
SET MENU
AMP
+
+
+
TV VOL
CH
VOLUME
–
–
–
SOURCE
2-6
ENTER
A-E/CAT.
MUTE
SET MENU
TITLE
MENU
BAND
SRCH MODE
AUDIO
ENTER
1,7
A-E/CAT.
PARAMETER
STRAIGHT
DISPLAY
RETURN
EFFECT
XM MEMORY
CLASSICAL
LIVE/CLUB
ENTERTAIN
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
7
8
NIGHT
ENHANCER
+ 10
ENT
9
0
3
MOVIE
(U.S.A. model)
Press ENTER to enter “MANUAL SETUP”.
The “MANUAL SETUP” display appears in the
OSD.
PRESET/CH
y
ENTER
;MANUAL SETUP
p
.1BASICMENU
2SOUNDMENU
3INPUTMENU
4OPTIONMENU
[]/[]:Up/Down
[ENTER]:Enter
A-E/CAT.
p
• You can change the “SET MENU” parameters while this unit is
reproducing sound.
• If you press PARAMETER during the “SET MENU” operation,
the “SET MENU” operation is canceled.
• Repeat the following procedure to select and adjust each
parameter setting.
• Press RETURN or l to return to the previous menu level.
y
You can also press h to enter the selected menu item.
Note
You cannot change some “SET MENU” parameters when
“NIGHT:CINEMA” or “NIGHT:MUSIC” is selected as the night
listening mode (see page 53).
1
[]/[]:Up/Down
[ENTER]:Enter
PURE DIRECT
p
TV INPUT
PRESET/CH
LEVEL
1
p
TV MUTE
TV
;AUTO SETUP
. ;MANUAL SETUP
. ;SIGNAL INFO
Set the operation mode selector to AMP and
then press SET MENU to enter “SET MENU”.
The top “SET MENU” display appears in the OSD.
4
Press k / n repeatedly and then press ENTER
to select and enter the desired menu.
The following displays are examples where “SOUND
MENU” is selected.
PRESET/CH
PRESET/CH
AMP
MENU
A-E/CAT.
A-E/CAT.
SRCH MODE
TV
SET MENU
.;AUTOSETUP
;MANUALSETUP
.;SIGNALINFO
2 SOUND MENU 1/2
2 SOUND MENU 2/2
. E)HDMI SET
p
[]/[]:Up/Down
[ENTER]:Enter
p
p
. A)EQUALIZER
B)LFE LEVEL
C)DYNAMIC RANGE
D)AUDIO SET
[]/[]:Up/Down
[ENTER]:Enter
p
p
p
[ ]/[]:Up/Down
[ENTER]:Enter
86 En
ENTER
ENTER
SET MENU
SOURCE
01EN_00_RX-V1700_U.book Page 87 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
5
Press k / n repeatedly and then press ENTER
to select and enter the desired submenu.
The following display is an example where “LFE
LEVEL” is selected.
1 BASIC MENU
Use this menu to manually adjust any speaker settings.
2 BASIC MENU
PRESET/CH
PRESET/CH
ENTER
ENTER
A-E/CAT.
p
p
. A)SPEAKERSET
B)SPLEVEL
C)SPDISTANCE
D)TESTTONE
[]/[]:Up/Down
[ENTER]:Enter
A-E/CAT.
■ Speaker settings A)SPEAKER SET
Use this feature to manually adjust any speaker settings.
B)LFE LEVEL
y
.SPEAKER;;;;;;0dB
HEADPHONE;;;;0dB
p
• If you are not satisfied with the bass sounds from your speakers,
you can change these settings according to your preference.
• When the diameter of the woofer section of the speaker unit is
larger than 16 cm (6.5 in), set the correspondent speaker setting
parameter to “LARGE” (or “LRG”).
6
p
[]/[]:Up/Down
[]/[]:Adjust
p [
Press k / n to select the desired parameter
and then l / h to change the parameter
settings.
• Press h to increase the value.
• Press l to decrease the value.
PRESET/CH
LFE/BASS OUT
PRESET/CH
ENTER
[
SWFRFRONTBOTH
A-E/CAT.
Press SET MENU to exit from “SET MENU”.
SET MENU
MENU
SRCH MODE
• Select “SWFR” (subwoofer) if you connected a
subwoofer. The LFE signals as well as the lowfrequency signals of other speakers set to “SML” (or
“SMALL”) are directed to the subwoofer.
• Select “FRONT” (front) if you did not connect a
subwoofer. The LFE signals, the low-frequency signals
of the front left and right channels, and the lowfrequency signals of other speakers set to “SML” (or
“SMALL”) are all directed to the front left and right
speakers regardless of the “FRONT SP” setting (see
page 87).
• Select “BOTH” (both) if you connected a subwoofer.
The low-frequency signals of any source are output
from the subwoofer. The LFE signals as well as the
low-frequency signals of other speakers set to “SML”
(or “SMALL”) are directed to the subwoofer. The lowfrequency signals of the front left and right channels
are directed to the front left and right speakers and the
subwoofer regardless of the “FRONT SP” setting (see
page 87).
87 En
ADVANCED
OPERATION
ENTER
A-E/CAT.
7
LFE/Bass out LFE/BASS OUT
Use this feature to select the speakers that output the LFE
(low-frequency effect) and the low-frequency signals.
Choices: SWFR, FRONT, BOTH
01EN_00_RX-V1700_U.book Page 88 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
Front speakers FRONT SP
Choices: SMALL, LARGE
FRONT SP
SMALLLARGE
[
• Select “SMALL” (small) if you have small front
speakers that do not reproduce low-frequency signals
effectively. The low-frequency signals of the front left
and right channels are directed to the speakers selected
in “LFE/BASS OUT” (see page 87).
• Select “LARGE” (large) if you have large front
speakers that reproduce low-frequency signals
effectively. All the front left and right channel signals
are directed to the front left and right speakers.
Notes
• When “LFE/BASS OUT” is set to “FRONT” (see page 87), the
LFE signals found in Dolby Digital or DTS sources, the lowfrequency signals of the front left and right channels, and the
low-frequency signals of other speakers set to “SML” (or
“SMALL”) are all directed to the front left and right speakers
regardless of the “FRONT SP” setting.
• When “LFE/BASS OUT” is set to “FRONT” (see page 87), you
can select only “LARGE” in “FRONT SP”. If the value of
“FRONT SP” is set to other than “LARGE” in advance, this
unit change the value to “LARGE” automatically.
Center speaker CENTER SP
Choices: NONE, SML, LRG
CENTER SP
NONESMLLRG
[
• Select “NONE” (none) if you did not connect a center
speaker. The center channel signals are directed to the
front left and right speakers.
• Select “SML” (small) if you have a small center
speaker that does not reproduce low-frequency signals
effectively. The low-frequency signals of the center
channel are directed to the speakers selected in “LFE/
BASS OUT”.
• Select “LRG” (large) if you have a large center speaker
that reproduces low-frequency signals effectively. All
the center channel signals are directed to the center
speaker.
88 En
Surround left/right speakers SUR. L/R SP
Choices: NONE, SML, LRG
SUR. L/R SP
NONESMLLRG
[
• Select “NONE” (none) if you did not connect surround
speakers. This unit is set to the Virtual CINEMA DSP
mode (see page 49) and “SUR. B L/R SP” is
automatically set to “NONE”.
• Select “SML” (small) if you have small surround left
and right speakers that do not reproduce low-frequency
signals effectively. The low-frequency signals of the
surround left and right channels are directed to the
speakers selected in “LFE/BASS OUT”.
• Select “LRG” (large) if you have large surround left
and right speakers that reproduce low-frequency
signals effectively. All the surround channel signals are
directed to the surround left and right speakers.
01EN_00_RX-V1700_U.book Page 89 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
Surround back speakers SB L/R SP
Choices: NONE, SMLx1, SMLx2, LRGx1, LRGx2
SB L/R SP
SMLx1 [
SMLx2
Presence speakers PRESENCE SP
Use this feature if you want to use the presence speakers
connected to this unit.
Choices: NONE, YES
CROSS OVER
FREQ;;;80Hz
Subwoofer phase SUBWOOFER PHASE
Use this feature to switch the phase of your subwoofer if
bass sounds are lacking or unclear.
Choices: NORMAL, REVERSE
02ASUBWOOFER PHASE
NORMALREVERSE
[
• Select “NORMAL” if you do not want to reverse the
phase of your subwoofer.
• Select “REVERSE” to reverse the phase of your
subwoofer.
Presence/Surround back channel priority
PRIORITY
Use this feature to prioritize either the presence or the
surround back speakers when playing sources that contain
surround back channel signals using the CINEMA DSP
sound field programs.
Choices: PRNS, SB
PRESENCE SP
PRIORITY
NONEYES
[
PRNS
• Select “NONE” (none) if you did not connect presence
speakers.
• Select “YES” (yes) if you connected presence speakers
and want to use them.
SB
[
• Select “PRNS” to use the presence speakers even when
surround back channel signals are input. The signals
for the surround back channel will be output from the
surround speakers.
• Select “SB” to use the surround back speakers when
surround back channel signals are detected in a
CINEMA DSP program. The presence channel signals
are output from the front speakers.
89 En
ADVANCED
OPERATION
• Select “NONE” (none) if you did not connect surround
back speakers. The surround back channel signals are
directed to the surround left and right speakers.
• Select “SMLx1” (small x 1) if you have a small
surround back speaker that does not reproduce lowfrequency signals effectively. The low-frequency
signals of the surround back left and right channels are
directed to the speakers selected in “LFE/BASS OUT”
and the rest of the signals are directed to the surround
back left speaker.
• Select “SMLx2” (small x 2) if you have two small
surround back speakers that do not reproduce lowfrequency signals effectively. The low-frequency
signals of the surround back left and right channels are
directed to the speakers selected in “LFE/BASS OUT”.
• Select “LRGx1” (large x 1) if you have a large
surround back speaker that reproduces low-frequency
signals effectively. All the surround back left and right
channel signals are directed to the surround back left
speaker.
• Select “LRGx2” (large x 2) if you have two large
surround back speakers that reproduce low-frequency
signals effectively. All the surround back left and right
channel signals are directed to the surround back left
and right speakers.
Bass cross over CROSS OVER
Use this feature to select the crossover frequency of all the
speakers set to “SML” (or “SMALL”) or to “NONE” in
“SPEAKER SET” (see pages 87 and 89). All frequencies
below the selected frequency will be sent to the subwoofer
or to the speakers set to “LRG” (or “LARGE”) in
“SPEAKER SET” (see pages 87 and 89).
Choices: 40Hz, 60Hz, 80Hz, 90Hz, 100Hz, 110Hz,
120Hz, 160Hz, 200Hz
01EN_00_RX-V1700_U.book Page 90 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
■ Speaker level
B)SP LEVEL
Use this feature to manually balance the speaker levels
between the front left or surround left speakers and each
speaker selected in “SPEAKER SET” (see page 87).
Control range: –10.0 to +10.0 dB
Control step: 0.5 dB
Initial setting:
FR. L/FR. R/SWFR/PR. L/PR. R: 0 dB
CENT./SUR. L/SUR. R/SB L/SB R: –1.0 dB
B)SP LEVEL
-__________+
.FR.L;;;;;;;;;;
FR.R;;;;;;;;;;
CENT.;;;;;;;;;;
■ Speaker distance C)SP DISTANCE
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sounds will arrive at the listening position at the same
time.
C)SP DISTANCE
p
p
[]/[]:Up/Down
[p]/[[]:Adjust
• Select “FR. L” to adjust the balance of the front left
speaker.
• Select “FR. R” to adjust the balance of the front right
speaker.
• Select “CENT.” to adjust the balance of the center
speaker.
• Select “SUR. L” to adjust the balance of the surround
left speaker.
• Select “SUR. R” to adjust the balance of the surround
right speaker.
• Select “SB L” to adjust the balance of the surround
back left speaker.
• Select “SB R” to adjust the balance of the surround
back right speaker.
• Select “SWFR” to adjust the balance of the subwoofer.
• Select “PR. L” to adjust the balance of the presence left
speaker.
• Select “PR. R” to adjust the balance of the presence
right speaker.
Notes
• “CENT.”, “SUR. L”, “SUR. R”, “SB L”, “SB R”, “SWFR”,
“PR. L” and “PR. R” cannot be adjusted if “CENTER SP” (see
page 88), “SUR. L/R SP” (see page 88), “SB.L/R SP” (see
page 89), “LFE/BASS OUT” (see page 87) and “PRESENCE
SP” (see page 89) are set to “NONE” respectively.
• Instead of “SB L” and “SB R”, “SB” is displayed if “SB.L/R
SP” is set to either “SMLx1” or “LRGx1” (see page 89).
90 En
p
p
. UNIT;;;;;;;;feet
FRONTL;;;10.0ft
FRONTR;;;10.0ft
CENTER;;;;8.5ft
[]/[]:Up/Down
[]/[]:Adjust
p [
Unit UNIT
Choices: meters (m), feet (ft)
Initial setting:
[U.S.A. and Canada models]: feet (ft)
[Other models]: meters (m)
• Select “meters” to adjust speaker distances in meters.
• Select “feet” to adjust speaker distances in feet.
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
Initial setting:
FRONT L/FRONT R/SWFR/PRNS L/
PRNS R: 3.00m (10.0ft)
CENTER: 2.60m (8.5ft)
SUR. L/SUR. R/SB L/SB R: 2.40m (8.0ft)
• Select “FRONT L” to adjust the distance of the front
left speaker.
• Select “FRONT R” to adjust the distance of the front
right speaker.
• Select “CENTER” to adjust the distance of the center
speaker.
• Select “SUR. L” to adjust the distance of the surround
left speaker.
• Select “SUR. R” to adjust the distance of the surround
right speaker.
• Select “SB L” to adjust the distance of the surround
back left speaker.
• Select “SB R” to adjust the distance of the surround
back right speaker.
• Select “SWFR” to adjust the distance of the subwoofer.
• Select “PRNS L” to adjust the distance of the presence
left speaker.
• Select “PRNS R” to adjust the distance of the presence
right speaker.
01EN_00_RX-V1700_U.book Page 91 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
2 SOUND MENU
Notes
• “CENTER”, “SUR. L”, “SUR. R”, “SB L”, “SB R”, “SWFR”,
“PRNS L” and “PRNS R” cannot be adjusted if “CENTER SP”
(see page 88), “SUR. L/R SP” (see page 88), “SUR. B L/R SP”
(see page 89), “LFE/BASS OUT” (see page 87) and
“PRESENCE SP” (see page 89) are set to “NONE”
respectively.
• Instead of “SB L” and “SB R”, “SB” is displayed if “SUR. B L/
R SP” is set to either “SMLx1” or “LRGx1” (see page 89).
■ Test tone D)TEST TONE
2 SOUND MENU 1/2
2 SOUND MENU 2/2
. E)HDMI SET
p
[]/[]:Up/Down
[ENTER]:Enter
p
p
. A)EQUALIZER
B)LFE LEVEL
C)DYNAMIC RANGE
D)AUDIO SET
[]/[]:Up/Down
[ENTER]:Enter
p
Turns the test tone output on or off for the SPEAKER
SET, SP LEVEL and SP DISTANCE settings.
Choices: ON, OFF
Use to manually adjust speaker settings or compensate for
video signal processing delays when using LCD monitors
or projectors. Most of the SOUND MENU parameters are
set automatically when you run AUTO SETUP (see
page 32).
D)TEST TONE
■ Equalizer A)EQUALIZER
TEST TONE;;;;OFF
Use this feature to select the parametric equalizer or the
graphic equalizer.
[]/[]:Select
)
)
Equalizer select SELECT
Use this feature to select the type of equalizer.
Choices: AUTO PEQ, GEQ, EQ OFF
y
If you use a handheld sound pressure level meter, hold at arm’s
length and point upwards so that the meter is in the listening
position. With the meter set to the 70 dB scale and to C SLOW,
calibrate each speaker to 75 dB.
A)EQUALIZER
SELECT;;;;;;;GEQ
)
)
[]/[]:Adjust
[ENTER]:Enter
Notes
• Select “AUTO PEQ” to use the parametric equalizer
adjusted in “AUTO SETUP” (see page 32).
• Select “GEQ” to adjust the built-in 7-frequency band
graphic equalizer so that the tonal quality of the
speaker matches. Press ENTER to display the graphic
equalizer screen.
• Select “EQ OFF” to deactivate the equalizing feature.
Note
You can select “AUTO PEQ” only when you carry out “AUTO
SETUP” in advance (see page 32). In this case, “AUTO PEQ” is
automatically selected as the default setting.
91 En
ADVANCED
OPERATION
• This function is automatically turned off if you exit “BASIC
MENU”.
• If you select “ON” and enter the “SPEAKER SET”, “SP
LEVEL” or “SP DISTANCE” menu, the test tone is output from
the selected speakers.
01EN_00_RX-V1700_U.book Page 92 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
Graphic equalizer
GEQ
Use to match the tonal quality of the center, surround L/R
and surround back L/R, surround back, presence L/R
speakers and the subwoofer with that of the front L/R
speakers. You can adjust 7 frequency bands (63Hz,
160Hz, 400Hz, 1kHz, 2.5kHz, 6.3kHz, 16kHz).
Choices: –6.0 to +6.0 dB
Control step: 0.5 dB
A)EQUALIZER
.CHANNEL;;FRONTL
-______+
63Hz ;;;;;;
0.0dB
160Hz ;;;;;;
0.0dB
400Hz ;;;;;;
0.0dB
■ Low-frequency effect level
B)LFE LEVEL
Use this feature to adjust the output level of the LFE (lowfrequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Control range: –20 to 0 dB
Control step: 1 dB
B)LFE LEVEL
p
.SPEAKER;;;;;;0dB
HEADPHONE;;;;0dB
p
[]/[]:Up/Down
[]/[]:Adjust
p [
p
Press k / n to select a frequency band and l / h to adjust the
selected frequency band.
Note
The “GEQ” parameter can be adjusted only when “GEQ” is
selected in “SELECT”.
Test tone
TEST TONE
A)EQUALIZER
CHANNEL;;FRONTL
-______+
16kHz ;;;;;;
0.0dB
p
p
. TESTTONE;;;;OFF
[]/[]:Up/Down
[]/[]:Adjust
p [
Use this feature to make adjustments of “GEQ” while
listening to a test tone. To select “TEST TONE”, press n
repeatedly in the graphic equalizer screen.
Choices: OFF, ON
• Select “OFF” to stop test tones and output the currently
selected source component.
• Select “ON” to output test tones from the selected
speakers.
p
[]/[]:Up/Down
[]/[]:Adjust
p [
y
Speaker SPEAKER
Adjusts the speaker LFE level.
Headphone HEADPHONE
Adjusts the headphone LFE level.
Note
Depending on the settings of “LFE/BASS OUT” (see page 87),
some signals may not be output at the SUBWOOFER OUTPUT
jack.
■ Dynamic range C)DYNAMIC RANGE
Use this feature to select the amount of dynamic range
compression to be applied to your speakers or
headphones. This setting is effective only when this unit is
decoding Dolby Digital and DTS signals.
Choices: MIN, STD, MAX
• Select “MIN” (minimum) if you regularly listen at low
volume levels.
• Select “STD” (standard) for general use.
• Select “MAX” (maximum) to preserve the greatest
amount of dynamic range.
C)DYNAMIC RANGE
.SP:MINSTDMAX
[
HP:MINSTDMAX
[
p
p
[]/[]:Up/Down
[]/[]:Select
p [
Speaker SP
Adjusts the speaker compression.
Headphone HP
Adjusts the headphone compression.
92 En
01EN_00_RX-V1700_U.book Page 93 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
■ Audio settings D)AUDIO SET
Use this feature to adjust the overall audio settings of this
unit.
■ HDMI set E)HDMI SET
Use this feature to select the component to play back
HDMI audio signals.
E)HDMI SET
D)AUDIO SET
SUPPORT AUDIO:
RX-V1700
[]/[]:Adjust
p [
p
p
. MUTE TYPE;;;FULL
A.DELAY;;;;;;0ms
TONE BYPASS;AUTO
LE>E
[]/[]:Up/Down
[]/[]:Adjust
p [
Muting type MUTING TYPE
Use this feature to adjust how much the mute function
reduces the output volume (see page 41).
Choices: FULL, –20dB
• Select “FULL” to completely mute all the audio
output.
• Select “–20dB” to reduce the current volume by 20 dB.
Audio delay AUDIO DELAY
Use this feature to delay the sound output and synchronize
it with the video image. This may be necessary when
using certain LCD monitors or projectors.
Control range: 0 to 240 ms
Control step: 1 ms
Note
The HDMI video signals input at the HDMI IN 1 or HDMI IN 2
jack of this unit are always output at the HDMI OUT jack of this
unit.
93 En
ADVANCED
OPERATION
Tone bypass TONE BYPASS
Use this feature to select whether the audio output
bypasses the tone control circuitry when “TREBLE” and
“BASS” are set to 0 dB (see page 50).
Choices: AUTO, OFF
• Select “AUTO” if you want the signals to bypass the
tone control circuitry to provide the purest signal
possible.
• Select “OFF” if you do not want the signals to bypass
the tone control circuitry.
Support audio SUPPORT AUDIO
Use to select whether to play back HDMI audio signals on
this unit or on another HDMI component connected to the
HDMI OUT jack on the rear panel of this unit.
Choices: RX-V1700, OTHER
• Select “RX-V1700” to play back HDMI audio signals
on this unit. The HDMI audio signals input at the
HDMI IN jacks of this unit are not output to the HDMI
component connected to the HDMI OUT jack on the
rear panel of this unit.
• Select “OTHER” to play back HDMI audio signals on
another HDMI component connected to the HDMI
OUT jack.
01EN_00_RX-V1700_U.book Page 94 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
3 INPUT MENU
Use this menu to reassign the input/output jacks, select the
input mode or rename the input source.
3 INPUT MENU 1/2
3 INPUT MENU 2/2
. E)MULTI CH SET
p
[]/[]:Up/Down
[ENTER]:Enter
p
p
p
. A)I/OASSIGNMENT
B)INPUT RENAME
C)VOLUME TRIM
D)DECODER MODE
[]/[]:Up/Down
[ENTER]:Enter
For COAXIAL INPUT jacks 1, 2 and 3
COAXIAL IN
Choices: (1) MD/TAPE, CD-R, CD, PHONO, DVD,
DTV, CBL/SAT, VCR 1, DVR/VCR 2,
V-AUX, MULTI CH
(2) MD/TAPE, CD-R, CD, PHONO, DVD,
DTV, CBL/SAT, VCR 1, DVR/VCR 2,
V-AUX, MULTI CH
(3) MD/TAPE, CD-R, CD, PHONO, DVD,
DTV, CBL/SAT, VCR 1, DVR/VCR 2,
V-AUX, MULTI CH
■ Input/output assignment
A)I/O ASSIGNMENT
Use this feature to assign the input/output jacks according
to the component to be used if the initial settings of this
unit do not correspond to your needs. Change the
following parameters to reassign the respective jacks and
effectively connect more components.
Once the input/output jacks are reassigned, you can select
the corresponding component by using the INPUT
selector on the front panel (or the input selector buttons on
the remote control).
y
The input source name in parentheses indicates the default
assigned input source.
For COMPONENT VIDEO jacks A, B and C
CMPNT-V IN
Choices: [A] DVD, DTV, CBL/SAT, VCR 1,
DVR/VCR 2, V-AUX
[B] DVD, DTV, CBL/SAT, VCR 1,
DVR/VCR 2, V-AUX
[C] DVD, DTV, CBL/SAT, VCR 1,
DVR/VCR 2, V-AUX
COAXIALIN
.(1);;;;;
CD
(
CD
)
(2);;;;; DVD
( DVD
)
(3);;;;;DVR/VCR2
(DVR/VCR2)
For OPTICAL INPUT jacks 4, 5, 6 and 7
OPTICAL IN
Choices: (4) MD/TAPE, CD-R, CD, PHONO, DVD,
DTV, CBL/SAT, VCR 1, DVR/VCR 2,
MULTI CH
(5) MD/TAPE, CD-R, CD, PHONO, DVD,
DTV, CBL/SAT, VCR 1, DVR/VCR 2,
MULTI CH
(6) MD/TAPE, CD-R, CD, PHONO, DVD,
DTV, CBL/SAT, VCR 1, DVR/VCR 2,
MULTI CH
(7) MD/TAPE, CD-R, CD, PHONO, DVD,
DTV, CBL/SAT, VCR 1, DVR/VCR 2,
MULTI CH
OPTICALIN1/2
CMPNT-VINPUT
.[A];;;;;DVD
(DVD)
[B];;;;;DTV
(DTV)
[C];;;;;CBL/SAT
(CBL/SAT)
94 En
OPTICALIN2/2
.(4);;;;;CD
(CD)
(5);;;;; DVD
(DVD )
(6);;;;;DTV
(DTV)
.(7);;;;;CBL/SAT
(CBL/SAT)
01EN_00_RX-V1700_U.book Page 95 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
For OPTICAL OUTPUT jacks 8 and 9
OPTICAL OUT
Choices: (8) MD/TAPE, CD-R, CD, PHONO, DVD,
DTV, CBL/SAT, VCR 1, DVR/VCR 2,
V-AUX
(9) MD/TAPE, CD-R, CD, PHONO, DVD,
DTV, CBL/SAT, VCR 1, DVR/VCR 2,
V-AUX
1
Press one of the input selector buttons on
the remote control to select the input source
you want to change the name of.
XM
PHONO
TUNER
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
V-AUX/DOCK CBL/SAT
DTV
VCR 1
OPTICALOUT
.(8);;;;;MD/TAPE
(MD/TAPE )
(9);;;;;;;CD-R
(CD-R)
2
Press l / h on the remote control to place
the “_” (underscore) under the space or the
character you want to edit.
PRESET/CH
Notes
• You cannot select a specific item more than once for the same
type of jack.
• When you connect a component to both the DIGITAL INPUT
(COAXIAL) and DIGITAL INPUT (OPTICAL) jacks, priority
is given to the signals input at the DIGITAL INPUT
(COAXIAL) jack.
ENTER
A-E/CAT.
3
Press k / n to select the character you want
to use and then press l / h to move to the
next space.
PRESET/CH
PRESET/CH
ENTER
HDMI IN
ADVANCED
OPERATION
For HDMI IN jacks 1and 2
HDMI IN
Choices: [IN1] DVD, DTV, CBL/SAT, VCR 1,
DVR/VCR 2, V-AUX
[IN2] DVD, DTV, CBL/SAT, VCR 1,
DVR/VCR 2, V-AUX
ENTER
A-E/CAT.
A-E/CAT.
.[IN1];;; DVD
( DVD )
[IN2];;;CBL/SAT
(CBL/SAT)
Notes
• You can use up to 8 characters for each input.
• Press n to change the character in the following order, or
press k to go in the reverse order:
A to Z, 0 to 9, a to z, symbols (#, *, –, +, etc.), space.
■ Input rename B) INPUT RENAME
Use this feature to change the name of the input source
that appears in the OSD and in the front panel display.
C)INPUTRENAME
4
Repeat steps 1 through 3 to rename each
input source.
5
Press SET MENU on the remote control to
exit from “INPUT RENAME”.
DVD->
DVD
________
p
p
[p]/[[]:Position
[]/[]:Chara.
SET MENU
y
MENU
SRCH MODE
• This feature is useful when you change the input or output
assignment for digital jacks and component video input jacks.
• You can also change the name of the input source that appears
in the display window on the remote control. Refer to
“Changing source names in the display window” on page 106”.
95 En
01EN_00_RX-V1700_U.book Page 96 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
■ Volume Trim C)VOLUME TRIM
Use this feature to adjust the level of the signal input at
each jack. This is useful if you want to balance the level of
each input source to avoid sudden changes in volume
when switching between input sources.
Choices: XM, TUNER, PHONO, CD, CD-R, MD/TAPE,
DVD, DTV, CBL/SAT, VCR 1, DVR/VCR 2,
V-AUX, DOCK, MULTI CH
Control range: –6.0 to +6.0 dB
Control step: 0.5 dB
Initial setting: 0.0 dB
■ Multi channel input Setup
E)MULTI CH SET
Use to set the direction of the signals input into the center,
subwoofer and surround channels when a source
component is connected to the MULTI CH INPUT jacks.
If you input 8-channel signals from an external decoder,
use this feature to select jacks for the additional front
signals.
E)MULTI CH SET
. BGV;;;;;;;;;LAST
INPUTCH;;;;;6CH
C)VOLUME TRIM
This parameter also affects the signals output at ZONE OUT
jacks.
■ Decoder mode D)DECODER MODE
Use to switch the input mode. You can designate the
reassigned digital input jacks for specific audio signals
(DTS, etc.).
Choices: AUTO, DTS
D)DECODER MODE
.
p
p
CD ;;;;AUTO
DVD ;;;;AUTO
DTV ;;;;AUTO
CBL/SAT ;;;;AUTO
[]/[]:Up/Down
[]/[]:Adjust
p [
p
p
p
y
p
[]/[]:Up/Down
[]/[]:Adjust
p
[
XM;;;0.0dB
TUNER;;;0.0dB
PHONO;;;0.0dB
CD;;;0.0dB
[]/[]:Up/Down
[]/[]:Adjust
p [
BGV BGV
Use this feature to select the video source played in the
background of the sources input from the MULTI CH
INPUT jacks.
Choices: DVD, DTV, CBL/SAT, VCR, DVR/VCR 2,
V-AUX, LAST, OFF
• Select “LAST” to set this unit to automatically select
the last selected video source as the background video
source.
• Select “OFF” to set this unit not to play the video
source in the background.
Input channels INPUT CH
Use this setting to select the number of channels input
from an external decoder.
Choices: 6CH, 8CH
• Select “6CH” if you input 6-channel signals.
• Select “8CH” if you input 8-channel signals.
Note
• Select “AUTO” if you want this unit to automatically
detect input signal types and select the appropriate
input mode.
• Select “DTS” if you want this unit to select DTS as the
input mode.
If “ZONE2 AMP” is set to “[SP1]”, “[SP2]” or “BOTH” (see
page 100), no sound is output from the surround back speakers
even if you select “8CH”. In this case, select “6CH” and set the
output setting of the external component to 6 channels.
Front input FRONT
E)MULTI CH SET
BGV;;;;;;;;;LAST
INPUTCH;;;;;8CH
.FRONT;;;;;;;;DVD
p
p
[]/[]:Up/Down
[]/[]:Adjust
p
[
If you selected 8ch in “INPUT CH”, you can select the
analog jacks at which the front signals from an external
decoder will be input.
Choices: MD/TAPE, CD-R, CD, DVD, DTV, CBL/SAT,
VCR1, DVR/VCR2, V-AUX
Note
“FRONT” parameter appears only when you set “INPUT CH” to
“8CH”.
96 En
01EN_00_RX-V1700_U.book Page 97 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
4 OPTION MENU
Use this menu to adjust the optional system parameters.
4 OPTION MENU 1/2
4 OPTION MENU 2/2
p
p
. E)PARAM. INI
F)ZONE SET
G)XM RADIO SET
H)DOCKSET
[]/[]:Up/Down
[ENTER]:Enter
p
p
. A)DISPLAYSET
B)MEMORY GUARD
C)AUDIO SELECT
D)DECODER MODE
[]/[]:Up/Down
[ENTER]:Enter
Gray back GRAY BACK
Use this feature to display a gray background in your
video monitor when there is no video signal being input.
Choices: AUTO, OFF
• Select “AUTO” to display a gray background in your
video monitor when there is no video signal being
input.
• Select “OFF” not to display a gray background in your
video monitor.
Notes
■ Display settings A)DISPLAY SET
Note
Use the “V-RESET” in “ADVANCED SETUP” to set the
parameters in “DISPLAY SET” (except “DIMMER”, “SHORT
MESSAGE”, “ON SCREEN” and “FL SCROLL”) to the factory
presets (see page 119).
A)DISPLAYSET
p
p
.DIMMER;;;;;;;;;;0
OSD SHIFT;;;;;;;0
GRAY BACK;;;;AUTO
VCONV.;;;;;;;;ON
[]/[]:Up/Down
[]/[]:Adjust
p [
OSD shift OSD SHIFT
Use this feature to adjust the vertical position of the OSD.
Control range: –5 (upward) to +5 (downward)
Control step: 1
Initial setting: 0
• Press l to raise the position of the OSD.
• Press h to lower the position of the OSD.
Video conversion V CONV.
Use this feature to set whether to convert the video signals
input at the VIDEO, S VIDEO and COMPONENT
VIDEO jacks.
Choices: ON, OFF
• Select “ON” to convert composite, S-video and
component video signals interchangeably and upconvert composite and S-video and component video
signals to HDMI video signals.
• Select “OFF” not to convert any signals.
Notes
• This unit does not convert 480 line video signals and 576 line
video signals interchangeably.
• The analog component video signals with 480i (NTSC)/576i
(PAL) of resolution are converted to the s-video or composite
video signals and output at the S VIDEO MONITOR OUT and
VIDEO MONITOR OUT jacks.
• The converted video signals are only output at the MONITOR
OUT jacks. When recording a video source, you must make the
same type of video connections between each component.
• When composite video or S-video signals from a VCR are
converted to component video signals, the picture quality may
suffer depending on your VCR.
• Set “V CONV.” to “ON” to display the sound field parameter
display and short message display.
• Unconventional signals input at the composite video or S-video
jacks cannot be converted or may be output abnormally. In such
cases, set “V CONV.” to “OFF”.
• When non-standard video signals (such as video signals from a
game console) are input, this unit may not convert the signals
even if you set “V CONV.” to “ON”.
97 En
ADVANCED
OPERATION
Dimmer DIMMER
Use this feature to adjust the brightness of the front panel
display.
Control range: – 4 to 0
Control step: 1
• Press l to make the front panel display dimmer.
• Press h to make the front panel display brighter.
• Depending on the video signals being input or the system
setting of your video monitor (NTSC or PAL), the OSD may be
displayed abnormally. In such cases, set “GRAY BACK” to
“OFF”.
• Even when “GRAY BACK” is set to “OFF”, the OSD may not
be displayed correctly depending on the conditions of the
picture.
01EN_00_RX-V1700_U.book Page 98 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
Component interlace/progressive up-conversion
CMPNT I/P
Use this feature to activate or deactivate the analog
interlace/progressive conversion of the analog video
signals input at the composite video, S-video and
component video jacks so that the analog video signals
deinterlaced from 480i (NTSC)/576i (PAL) to 480p/576p
are output at the COMPONENT MONITOR OUT jacks.
Choices: ON, OFF
• Select “ON” to activate the analog interlace/
progressive up-conversion of the analog video signals.
• Select “OFF” to deactivate the analog interlace/
progressive up-conversion of the analog video signals.
Notes
• This menu item is not available and hence not visible in the
OSD if “V CONV.” is set to “OFF”.
• If your video monitor does not support analog video signals
with 480p/576p of resolution, the SET MENU items may not be
displayed on your video monitor when “CMPNT I/P” is set to
“ON”. Use “V-RESET” in “ADVANCED SETUP” to set the
“CMPNT I/P” parameter to the factory preset setting (see
page 119).
HDMI interlace/progressive up-conversion
HDMI I/P
Use this feature to activate or deactivate the HDMI
interlace/progressive up-conversion of the analog video
signals input at the composite video, S-video and
component video jacks so that the analog video signals
deinterlaced from 480i (NTSC)/576i (PAL) to 480p/576p
are output at the HDMI OUT jack.
Choices: ON, OFF
• Select “ON” to activate the HDMI interlace/
progressive up-conversion of the analog video signals.
• Select “OFF” to deactivate the HDMI interlace/
progressive up-conversion of the analog video signals.
Note
The short message display does not appear in the following cases:
– when the component video signals with 480p/576p, 720p,
1080i or 1080p resolutions are input
– When HDMI video signals are input
On-screen display time ON SCREEN
Use this feature to set the amount of time to display the
XM Satellite Radio information or iPod menu in the OSD
after you perform a certain operation.
Choices: ALWAYS, 10SEC, 30SEC
• Select “ALWAYS” to display the OSD unceasingly
during an operation.
• Select “10SEC” to turn off the OSD 10 seconds after
you perform a certain operation.
• Select “30SEC” to turn off the OSD 30 seconds after
you perform a certain operation.
Front panel display scroll FL SCROLL
Use this feature to set whether to display the information
(such as song title or channel name) in the front panel
display in a continuous manner or by the first 14
alphanumeric characters after scrolling all characters once
when “XM” or “DOCK” is selected as the input source.
Choices: CONT, ONCE
• Select “CONT” to display the operation status in the
front panel display in a continuous manner.
• Select “ONCE” to display the operation status in the
front panel display by the first 14 alphanumeric
characters after scrolling all characters once.
■ Memory guard B)MEMORY GUARD
Use this feature to prevent accidental changes to DSP
program parameter values and other system settings.
Choices: OFF, ON
B)MEMORYGUARD
Notes
• This menu item is not available and hence not visible in the
OSD if “V CONV.” is set to “OFF”.
• When analog video signals with 1080i or 720p of resolution are
up-converted to HDMI and output at the HDMI OUT jack, the
picture quality may worsen.
Short message display
SHORT MESSAGE
Use this feature to activate or deactivate the short message
display function.
Choices: ON, OFF
• Select “ON” to activate the short message display
function. The contents of the front panel display appear
at the bottom of the screen each time you operate this
unit.
• Select “OFF” to deactivate the short message display
function.
98 En
OFFON
[
[]/[]:Adjust
p
[
• Select “OFF” to turn off the “MEMORY GUARD”
feature.
• Select “ON” to protect:
– DSP sound field program parameters
– all “SET MENU” items
– all speaker levels
Note
When “MEMORY GUARD” is set to “ON”, you cannot select
and adjust any other “SET MENU” items.
01EN_00_RX-V1700_U.book Page 99 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
■ Audio select
C)AUDIO SELECT
Use this feature to designate the default input mode for the
input sources connected to the DIGITAL INPUT jacks
when you turn on the power of this unit.
Choices: AUTO, LAST
C)AUDIO SELECT
[AUTO
LAST
[p]/[[]:Adjust
• Select “AUTO” if you want this unit to automatically
detect the type of input signals and select the
appropriate input mode.
• Select “LAST” if you want this unit to automatically
select the last input mode used for the connected input
source.
■ Parameter initialization E)PARAM.INI
Use this feature to initialize the parameters of each sound
field program within a sound field program group. When
you initialize a sound field program group, all of the
parameter values within that group revert to their initial
factory settings.
Press the corresponding sound field program selector
buttons on the remote control to select the sound field
program that you want to initialize.
An asterisk (*) appears to the left of the sound field
program names that have been changed from their initial
factory settings.
Choices: CLASSICAL, LIVE/CLUB,
ENTERTAINMENT, MOVIE, STEREO,
SURROUND DECODE
E)PARAM.INI
CLASSICAL
*LIVE/CLUB
ENTERTAINMENT
*MOVIE
STEREO
SURROUNDDECODE
Press DSP key
Note
Selecting “LAST” does not recall the last setting for the EXTD
SUR. button on the remote control.
■ Decoder mode D)DECODER MODE
Use this feature to designate the default decoder mode for
the input sources connected to the DIGITAL INPUT jacks
when you turn on the power of this unit.
Choices: AUTO, LAST
[AUTO
LAST
• You cannot automatically revert to the previous parameter
settings once you initialize a sound field program group.
• You cannot separately initialize individual sound field
programs.
• You cannot initialize any sound field program groups when
“MEMORY GUARD” is set to “ON” (see page 98).
■ Zone set F)ZONE SET
[p]/[[]:Adjust
F)ZONE SET
p
Note
Selecting “LAST” does not recall the last setting for the EXTD
SUR. button on the remote control.
p
• Select “AUTO” to if you want this unit to
automatically detect the type of input signals and select
the appropriate decoder mode.
• Select “LAST” to if you want this unit to automatically
select the last decoder mode used the connected input
source.
. ZONE2 VOL;;;;VAR
ZONE3 VOL;;;;VAR
ZONE2 AMP;;;;EXT
ZONE3 AMP;;;;EXT
[]/[]:Up/Down
[]/[]:Adjust
p
[
Zone 2 volume ZONE2 VOL
Zone 3 volume ZONE3 VOL
Use to select how the volume control will operate with
regard to the ZONE 2 OUTPUT or ZONE 3 OUTPUT
jacks.
Choices: VAR, FIX
• Select “VAR” to adjust the ZONE 2 OUTPUT or
ZONE 3 OUTPUT volume simultaneously with
VOLUME +/– on the remote control.
• Select “FIX” to fix the ZONE 2 OUTPUT or ZONE 3
OUTPUT volume level to a standard line level.
99 En
ADVANCED
OPERATION
D)DECODER MODE
Notes
01EN_00_RX-V1700_U.book Page 100 Tuesday, June 27, 2006 9:37 AM
CUSTOMIZING THIS UNIT (MANUAL SETUP)
Zone 2 amplifier ZONE2 AMP
Zone 3 amplifier ZONE3 AMP
Use to select how the ZONE 2 and/or ZONE 3 speakers
are amplified.
Choices: EXT, [SP1], [SP2], BOTH
• Select “EXT” if you want to connect your Zone 2 or
Zone 3 speakers through an external amplifier
connected to the ZONE 2 OUTPUT or ZONE 3
OUTPUT jacks on the rear panel of this unit.
• Select “[SP1]” to use the internal surround back
amplifier of this unit when you want to connect your
Zone 2 or Zone 3 speakers directly to the SP1 speaker
terminals on the rear panel of this unit.
• Select “[SP2]” to use the internal surround amplifier of
this unit when you want to connect your Zone 2 or
Zone 3 speakers directly to the SP2 speaker terminals
on the rear panel of this unit.
• Select “BOTH” to use the internal surround and
surround back amplifiers of this unit when you want to
connect your Zone 2 or Zone 3 speakers directly to
both the SP1 and the SP2 speaker terminals on the rear
panel of this unit.
Notes
• When “BI-AMP” is set to “ON” in the “ADVANCED SETUP”
menu, “[SP1]”, “[SP2]” and “BOTH” cannot be selected.
• When “BOTH” is selected for “ZONE2 AMP”, only “EXT” can
be selected for “ZONE3 AMP”.
• When “BOTH” is selected for “ZONE3 AMP”, only “EXT” can
be selected for “ZONE2 AMP”.
• When you set “ZONE2 AMP” or “ZONE3 AMP” to “[SP1]” or
“[SP2]” and the corresponding zone is turned on, no sound is
output from the surround back speakers.
• When you set “ZONE2 AMP” or “ZONE3 AMP” to “BOTH”
and the corresponding zone is turned on, no sound is output
from both the surround speakers and the surround back speakers
in the main zone.
• When both “ZONE2 AMP” and “ZONE3 AMP” are set to
“[SP1]” or “[SP2]” and Zone 2 and Zone 3 are turned on, no
sound is output from both the surround speakers and the
surround back speakers in the main zone.
• When you use internal amplifiers for Zone 2 or Zone 3, some
surround field programs may not work in the same way as when
you do not use the internal amplifiers for Zone 2 or Zone 3.
100 En
■ XM Radio setting G)XM RADIO SET
(U.S.A. and Canada models only)
G)XM RADIO SET
.XM ANTENNA;;NONE
XM Radio antenna XM ANTENNA
Use this feature to check the current reception level of the
XM Passport System connected to the XM jack of this
unit (see page 61). For the best reception, orient the XM
Passport System so that a value of 60% or more is
displayed here.
Display status: NONE, 0 to 100%
Notes
• “NONE” is displayed if the XM Passport System is not connected to
this unit. In this case, check the antenna connections (see page 61).
• The “XM ANTENNA” parameter cannot be adjusted by using
the remote control. Instead, you need to adjust the orientation of
the XM Passport System connected to the XM jack of this unit
for a better percentage of the reception level.
■ Dock set H)DOCK SET
H)DOCK SET
.STANDBYCHRG;AUTO
[]/[]:Select
)
)
[ENTER]:Return
Charge on standby STANDBY CHRG
Use this feature to select whether this unit charges the
battery of the stationed iPod or not when this unit is in the
standby mode (see page 73).
Choices: AUTO, OFF
• Select “AUTO” to charge the battery of the stationed
iPod when this unit is turned on and in the standby
mode.
• Select “OFF” to charge the battery of the stationed
iPod only when this unit is turned on.
01EN_00_RX-V1700_U.book Page 101 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
REMOTE CONTROL FEATURES
In addition to controlling this unit, the remote control can also operate other audiovisual components made by YAMAHA
and other manufacturers. To control your TV or other components, you must set up the appropriate remote control code
for each input source (see page 103).
Controlling this unit, a TV, or other components
■ Controlling this unit
■ Controlling a TV
Set the operation mode selector to AMP to control this
unit (see page 6).
Set the operation mode selector to TV to control your TV.
To control your TV, you must set the appropriate remote
control code for DTV or PHONO (see page 103). When
you set the remote control codes for both DTV and
PHONO, priority is given to the one set for DTV.
POWER
POWER
TV
AV
XM
PHONO
TUNER
V-AUX/DOCK CBL/SAT
DTV
VCR 1
STANDBY
POWER
AUDIO SEL
SLEEP
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
*1
*1
POWER
POWER
TV
AV
PHONO
TUNER
V-AUX/DOCK CBL/SAT
DTV
POWER
STANDBY
XM
VCR 1
AUDIO SEL
SLEEP
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
SELECT
SELECT
AMP
AMP
+
+
+
TV VOL
CH
VOLUME
+
+
+
TV VOL
CH
VOLUME
–
LEVEL
–
–
TV INPUT
MUTE
PRESET/CH
MENU
SRCH MODE
*1
TV
SET MENU
TITLE
BAND
PURE DIRECT
*1
LEVEL
TV
–
TV INPUT
MUTE
PRESET/CH
SET MENU
TITLE
MENU
BAND
SRCH MODE
PURE DIRECT
AUDIO
ENTER
PARAMETER
STRAIGHT
DISPLAY
RETURN
EFFECT
XM MEMORY
PARAMETER
*1
STRAIGHT
DISPLAY
RETURN
EFFECT
XM MEMORY
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
CLASSICAL
LIVE/CLUB
ENTERTAIN
1
2
3
4
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
7
8
5
6
7
8
NIGHT
ENHANCER
NIGHT
ENHANCER
9
0
+ 10
ENT
9
0
+ 10
ENT
*2
*2
DISC SKIP
DISC SKIP
ON
MOVIE
REC
REC
OFF
ADVANCED
OPERATION
A-E/CAT.
A-E/CAT.
MACRO
LEARN
CLEAR
OFF
RENAME
(U.S.A. model)
Notes
*1
–
–
TV MUTE
AUDIO
ENTER
*2
SOURCE
SOURCE
TV MUTE
*2
These buttons always control this unit regardless of the
operation mode selector position.
*2 These buttons control this unit only when the component
operation mode selector is set to AMP.
ON
MACRO
LEARN
CLEAR
RENAME
(U.S.A. model)
Notes
*1
These buttons always control your TV regardless of the
operation mode selector position.
Remote control
*2
Digital TV/Cable TV
TV POWER
Turns on or off the power.
TV VOL +/–
Increases or decreases the volume
level.
TV MUTE
Mutes the audio output.
TV INPUT
Changes the input source.
These buttons control your TV only when the operation mode
selector is set to TV. For details, see the “TV” column on
page 102.
101 En
01EN_00_RX-V1700_U.book Page 102 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
■ Controlling other components
Set the operation mode selector to SOURCE to control
other components selected with the input selector buttons
or . You must set the appropriate remote control code for
each input source in advance (see page 103). The
following table shows the function of each control button
used to control other components assigned to each input
selector button or . Be advised that some buttons may
not correctly operate the selected component.
1
POWER
POWER
TV
AV
XM
PHONO
STANDBY
POWER
AUDIO SEL
SLEEP
TUNER
CD
MULTI CH IN
3
4
5
LEVEL
DTV
VCR 1
MD/TAPE
CD-R
DVR/VCR 2
DVD
6
SET MENU
MENU
SRCH MODE
8
9
PURE DIRECT
AUDIO
ENTER
A-E/CAT.
PARAMETER
STRAIGHT
DISPLAY
RETURN
LIVE/CLUB
ENTERTAIN
1
2
3
STEREO
SUR. DECODE
SELECT
5
6
0
9
0
EFFECT
XM MEMORY
CLASSICAL
V-AUX/DOCK CBL/SAT
PRESET/CH
TITLE
BAND
MOVIE
4
EXTD SUR.
7
8
NIGHT
ENHANCER
+ 10
ENT
A
SELECT
2
AMP
+
+
+
TV VOL
CH
VOLUME
–
–
–
TV MUTE
TV INPUT
MUTE
7
REC
DISC SKIP
SOURCE
y
The remote control has 14 modes (input areas) to control
components so that the remote control can operate up to 14
different components.
DVD player/
DVD
recorder
1
2
3
4
AV POWER Power *1
ON
MACRO
LEARN
CLEAR
RENAME
(U.S.A. model)
VCR
Cable TV/
Satellite
tuner
TV
LD player
CD player
MD recorder/
Tape deck
CD recorder
Tuner
Power *1
Power *1
VCR power
Power *1
Power *1
Power *1
Power *1
Power *1
TV
channel up*3
TV
channel up*3
TV
channel up*3
TV
channel up*3
TV
channel up*3
TV
channel up*3
TV channel
down*3
TV channel
down*3
TV channel
down*3
TV channel
down*3
TV channel
down*3
TV channel
down*3
*2
CH +
TV
channel up*3
Channel up
CH –
TV channel
down*3
Channel down Channel down Channel down
TITLE
Title
Title
ENTER
PRESET/CH k
OFF
TV
Channel up
Channel up
iPod
Title
Title
Band
Menu enter
Menu select
Menu select
Menu up
Menu up
Menu up
Preset up
(1 to 8)
Up
Down
Subsequent
menu
Menu down
Menu down
Menu down
Preset down
(1 to 8)
A-E/CAT. l
Menu left
Menu left
Menu left
Preset down
(A to E)
Previous
menu
A-E/CAT. h
Menu right
Menu right
Menu right
Preset up
(A to E)
Subsequent
menu
PRESET/CH n
5
6
7
8
9
0
A
Direction A/B
RETURN
Return
Return
Return
Return
1-9, 0, +10
Numeric
buttons
Numeric
buttons
Numeric
buttons
Numeric
buttons
Numeric
buttons
Numeric
buttons
Numeric
buttons
ll
Search
backward
Search
backward
VCR search
backward *2
VCR search
backward *2
Search
backward
Search
backward
Search
backward
Search
backward
Search
backward*4
hh
Search
forward
Search
forward
VCR search
forward *2
VCR search
forward *2
Search
forward
Search
forward
Search
forward
Search
forward
Search
forward*4
b
Skip
backward
Chapter/Skip
backward
Skip
backward
Skip
backward
Direction
back
Skip
backward
a
Skip forward
Chapter/Skip
forward
Skip forward
Skip forward
Direction
forward
Skip
forward
REC/
DISC SKIP
Disc skip (player)
Rec
Rec (recorder)
VCR rec *2
VCR rec *2
Disc skip
Rec
Rec
s
Stop
Stop
VCR stop *2
VCR stop *2
Stop
Stop
Stop
Stop
e
Pause
Pause
VCR pause *2 VCR pause *2 Pause
Pause
Pause
Pause
Pause
(Play/Pause)*5
p
Play
Play
VCR play *2
VCR play *2
Play
Play
Play
Play
(Play/Pause)*5
MENU
Menu
Menu
Menu
AUDIO
Audio
DISPLAY
Display
Display
Display
Enter/recall
Enter
ENT
Stop
Play
Previous
menu
Audio
Enter
Display
Display
Display
Display
Notes
*1
This button is operational only when the original remote control supplied with the component has a POWER button.
These buttons operate your VCR only when you set the appropriate remote control code for VCR 1 (see page 103).
*3 These buttons control your TV only when the operation mode selector is set to TV. For details, see the “TV” column on page 102.
*4 Press and hold to search backward or forward.
*5 Simple remote mode (see page 73)
*2
102 En
01EN_00_RX-V1700_U.book Page 103 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
■ Selecting a component to be controlled
You can select a component to be controlled
independently of the input source selected with the input
selector buttons.
Press SELECT k / n repeatedly to select the
desired component.
The name of the component to be controlled appears in the
display window on the remote control.
Setting remote control codes
You can control other components by setting the
appropriate remote control codes. Codes can be set up for
each input area. For a complete list of available remote
control codes, refer to “LIST OF REMOTE CONTROL
CODES” at the end of this manual.
The following table shows the default component
(Library: component category) and the remote control
code for each input area.
SELECT
Remote control code default settings
Input area
■ Controlling optional components
(Option mode)
XM
“OPTN” is an optional component control area that can be
programmed with remote control functions independently
from any input source. This area is useful for
programming commands that are to be used only as a part
of a macro function or for components that do not have a
valid remote control code.
To select the option mode, press SELECT n
repeatedly until “OPTN” appears in the display
window on the remote control.
Note
You cannot set a remote control code for the optional area. See
page 105 to program buttons operated within this component
control area.
Manufacturer
Default
code
TUNER
YAMAHA
2604
TUNER
YAMAHA
2607
PHONO
TV
–
–
TUNER
TUNER
YAMAHA
2602
CD
CD
YAMAHA
2300
MULTI CH
INPUT
DVD
YAMAHA
2100
V-AUX/
DOCK
TUNER
YAMAHA
2606
CBL/SAT
CABLE
–
–
MD/TAPE
MD
YAMAHA
2500
CD-R
CD-R
YAMAHA
2400
DTV
TV
–
–
VCR 1
VCR
–
–
DVR/VCR2
DVR
YAMAHA
2807
DVD
DVD
YAMAHA
2100
Note
You may not be able to operate your YAMAHA component even
if a YAMAHA remote control code is preset as listed above.
In this case, try setting another YAMAHA remote control code.
1
Set the operation mode selector to SOURCE
and then press an input selector button or
to select the input area you want to set up.
XM
AMP
PHONO
TUNER
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
SOURCE
V-AUX/DOCK CBL/SAT
TV
DTV
VCR 1
103 En
ADVANCED
OPERATION
SELECT
Library
(component
category)
01EN_00_RX-V1700_U.book Page 104 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
2
Press and hold LEARN for about 3 seconds
using a ballpoint pen or similar object.
The library name (ex. L;DVD) and the name of the
selected input area (ex. DVD) appear alternately in
the display window on the remote control.
4
Press the numeric buttons to enter the
four-digit remote control code for the
component you want to use.
For a complete list of available remote control codes,
refer to “LIST OF REMOTE CONTROL CODES” at
the end of this manual.
CLASSICAL
LIVE/CLUB
ENTERTAIN
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
7
8
9
0
MOVIE
LEARN
y
• You can set a remote control code of a different type of
component to an input area. Press l / h repeatedly to
change the library (component category).
Library choices: L;DVD, L;DVR, L;LD, L;CD, L;CDR,
L;MD, L;TAP (tape), L;TUN (tuner),
L;AMP, L;TV, L;CAB (cable),
L;SAT (satellite), L;VCR
• If you want to setup for another input area, press the input
selector button or , or press SELECT k / n repeatedly to
select the input area.
5
y
If you continuously want to set up another code for another
component, press the input selector button or , or
SELECT k / n repeatedly to select the component, then
repeat steps 2 through 5.
Notes
• Be sure to press and hold LEARN for at least 3 seconds,
otherwise the learning process will start.
• If you do not complete each of the following steps within
30 seconds, the setting mode will be automatically
canceled. In this case, start over from step 2.
3
Press ENTER.
The four-digit code set for the selected component
appears in the display window.
Note
0000 appears in the display window if no code has been set.
Press ENTER to set the number.
“OK” appears in the display window on the remote
control if setting was successful.
“NG” appears in the display window on the remote
control if the setting was unsuccessful. In this case,
start over from step 3.
6
Press LEARN again to exit from the setup
mode.
LEARN
7
Press p or AV POWER to confirm whether
you can control your component using the
remote control.
POWER
or
AV
y
If operation is not possible and the manufacturer of your
component has more than one code, try each of them until
you find the correct one.
Notes
• “ERROR” appears in the display window on the remote control
if you press a button not indicated in the respective step, or
when you press more than one button simultaneously.
• The supplied remote control does not contain all possible codes
for commercially available audio and video components
(including YAMAHA components). If operation is not possible
with any of the remote control codes, program the new remote
control function using the learn feature (see “Programming
codes from other remote controls”) or use the remote control
supplied with the component.
• Functions programmed using the learn feature take priority over
remote control code functions.
104 En
01EN_00_RX-V1700_U.book Page 105 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
Programming codes from other
remote controls
2
TV
AV
POWER
XM
TUNER
POWER
PHONO
SLEEP
POWER
CD-R
MULTI CH IN
STANDBY
CD
AUDIO SEL
MD/TAPE
AUDIO SEL
Other remote control
PURE DIRECT
MENU
5 to 10 cm (2 to 4 in)
AUDIO
ENTER
XM
(U.S.A. model)
SRCH MODE
BAND
POWER
V-AUX/DOCK CBL/SAT
STANDBY
DVD
AV
DVR/VCR 2
POWER
TV
VCR 1
SET MENU
TITLE
POWER
SELECT
LEVEL
PRESET/CH
DTV
You can program remote control codes from other remote
controls. Use the learn feature if you want to program
functions not included in the basic operations covered by
the remote control codes, or an appropriate remote control
code is not available. You can program the function of
other remote control to the buttons in the highlighted areas
in the following illustration. The buttons can be
programmed independently for each input area.
Place this remote control about 5 to 10 cm
(2 to 4 in) apart from the other remote control
on a flat surface so that their infrared
transmitters are aimed at each other.
SLEEP
A-E/CAT.
PARAMETER
PHONO
TUNER
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
STRAIGHT
DISPLAY
RETURN
EFFECT
XM MEMORY
V-AUX/DOCK CBL/SAT
DTV
VCR 1
CLASSICAL
LIVE/CLUB
ENTERTAIN
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
0
9
MOVIE
7
8
NIGHT
ENHANCER
+ 10
ENT
3
Press LEARN using a ballpoint pen or similar
object.
“LEARN” and the name of the selected input area
(ex. “DVD”) appear alternately in the display window
on the remote control.
SELECT
REC
AMP
+
+
+
DISC SKIP
SOURCE
TV VOL
CH
VOLUME
–
–
–
TV MUTE
TV INPUT
MUTE
OFF
ON
MACRO
LEARN
CLEAR
RENAME
TV
(U.S.A. model)
LEARN
Note
1
Notes
• Do not press and hold LEARN. If you hold it down for
more than 3 seconds, the remote enters the remote control
code setting mode.
• If you do not complete each of the following steps within
30 seconds, the learning mode will be automatically
canceled. In this case, start over from step 3.
Set the operation mode selector to SOURCE
and then press an input selector button or
to select an input area.
XM
AMP
4
PHONO
TUNER
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
Press the button for which you want to
program the new function.
“LEARN” appears in the display window on the
remote control.
SOURCE
V-AUX/DOCK CBL/SAT
TV
DTV
VCR 1
TV
AV
POWER
TUNER
POWER
XM
PHONO
SLEEP
POWER
MULTI CH IN
STANDBY
CD
AUDIO SEL
DVD
CD-R
SELECT
TV
AMP
SOURCE
MD/TAPE
+
DVR/VCR 2
–
VOLUME
VCR 1
+
DTV
–
CH
V-AUX/DOCK CBL/SAT
+
PURE DIRECT
AUDIO
EFFECT
STRAIGHT
–
MUTE
SET MENU
PARAMETER
TV VOL
TV INPUT
MENU
ENTER
PRESET/CH
SRCH MODE
LEVEL
TITLE
TV MUTE
BAND
A-E/CAT.
DISPLAY
4
RETURN
XM MEMORY
8
MOVIE
EXTD SUR.
3
ENTERTAIN
SELECT
2
LIVE/CLUB
SUR. DECODE
ENT
ENHANCER
7
+ 10
NIGHT
RENAME
1
STEREO
6
CLEAR
CLASSICAL
0
LEARN
9
MACRO
5
ON
REC
DISC SKIP
OFF
(U.S.A. model)
(U.S.A. model)
Note
Make sure that the operation mode selector is set to SOURCE.
When you set the operation mode selector to AMP and program a
remote control codes from other remote controls, the
programmed key cannot operate the amplifier function of this
unit.
105 En
ADVANCED
OPERATION
The remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn most
of its functions. However, you may not be able to program some
special signals or extremely long transmissions. Refer to the
operating instructions for the other remote control.
01EN_00_RX-V1700_U.book Page 106 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
5
Press and hold the button you want to
program on the other remote control until
“OK” appears in the display window on the
remote control.
“NG” appears in the display window on the remote
control if learning was unsuccessful. In this case, start
over from step 4.
TV
POWER
XM
PHONO
DTV
You can change the name of the input source that appears
in the display window on the remote control if you want to
use a different name than the factory preset. This feature is
useful when you have set an input area to control a
different component.
AV
1
POWER
TUNER
VCR 1
V-AUX/DOCK CBL/SAT
SLEEP
MULTI CH IN
POWER
CD
DVD
CD-R
STANDBY
MD/TAPE
AUDIO SEL
DVR/VCR 2
SELECT
(U.S.A. model)
Changing source names in the
display window
Other remote control
Set the operation mode selector to AMP or
SOURCE and then press an input selector
button or to select the input area you want
to rename.
The name of the selected input area appears in the
display window.
AMP
XM
SOURCE
TV
y
• If you want to program another function, repeat steps 4
and 5.
• If you continuously want to program another function for
another component, press SELECT k / n to select the
component, and then repeat steps 4 and 5.
6
PHONO
or
TUNER
V-AUX/DOCK CBL/SAT
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
AMP
DTV
VCR 1
SOURCE
TV
(U.S.A. model)
Press LEARN again to exit the learning
mode.
LEARN
Notes
• “ERROR” appears in the display window on the remote control
if you press a button not indicated in the respective step, or
when you press more than one button simultaneously.
• This remote control can learn approximately 200 functions.
However, depending on the signals learned, “FULL” may
appear in the display before you program 200 functions. In this
case, clear unnecessary programmed functions to make room
for further learning.
• Learning may not be possible in the following cases:
– when the batteries in the remote control for this unit or other
components are weak.
– when the distance between the two remote controls is too
great or too small.
– when the remote control infrared windows are not facing each
other at the appropriate angle.
– when the remote control is exposed to direct sunlight.
– when the function to be programmed is continuous or
uncommon.
106 En
2
Press RENAME using a ballpoint pen or
similar object.
RENAME
Note
If you do not complete each of the following steps within 30
seconds, the renaming mode will be automatically canceled.
In this case, start over from 2.
01EN_00_RX-V1700_U.book Page 107 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
3
Press k / n to select and enter a character.
Pressing n changes the character as follows:
A to Z, 1 to 9, 0, + (plus), – (hyphen), ; (semicolon),
/ (slash), and space.
Pressing k changes the characters in reverse order.
PRESET/CH
ENTER
A-E/CAT.
Macro programming features
The macro programming feature makes it possible to
perform a series of operations with the press of a single
button. For example, when you want to play a CD,
normally you would turn on the components, select the
CD input, and press the play button to start playback. The
macro programming feature lets you perform all of these
operations simply by pressing the CD macro button. The
buttons listed as macro buttons below are factory set with
macro programs. You can also program your own macros
(see page 109).
■ MACRO operations
4
Press h to move the cursor to the next
position.
Macro buttons
PRESET/CH
POWER
POWER
TV
AV
STANDBY
(U.S.A. model)
POWER
REC
XM
AUDIO SEL
SLEEP
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
DISC SKIP
PHONO
TUNER
V-AUX/DOCK CBL/SAT
ENTER
DTV
VCR 1
OFF
ON
MACRO
LEARN
CLEAR
RENAME
A-E/CAT.
MACRO ON/OFF
y
Press l to move the cursor to the previous position.
5
1
Set the MACRO ON/OFF selector to ON.
OFF
ON
MACRO
LEARN
CLEAR
ADVANCED
OPERATION
Press ENTER to set the new name.
“OK” appears in the display window on the remote
control if renaming was successful.
“NG” appears in the display window on the remote
control if renaming was unsuccessful. In this case,
start over from step 3.
MACRO
2
Press the desired macro button.
3
Set the MACRO ON/OFF selector to OFF
when you finish to using the macro
programming operation.
y
If you continuously want to rename another input area, press
the input selector button or , or press SELECT k / n
repeatedly to select the component, then repeat steps 3
through 5.
6
OFF
Press RENAME again to exit the renaming
mode.
ON
MACRO
LEARN
CLEAR
RENAME
Notes
Note
“ERROR” appears in the display window on the remote control if
you press a button not indicated in the respective step, or when
you press more than one button simultaneously.
y
• While the remote control is running a macro program, it does
not accept any other operation until it has completed running
the program (the transmission indicator stops flashing).
• Continue to aim the remote control at the component the macro
is operating until the macro operation is complete.
This feature is useful when you change the input or output
assignment for digital jacks and component video input jacks.
Refer to “INPUT RENAME” on page 95.
107 En
01EN_00_RX-V1700_U.book Page 108 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
■ Default macro functions
Pressing
macro button
To automatically transmit these signals in order
First
Second
Third
STANDBY
STANDBY
POWER
POWER
—
—
(*1)
(*2)
POWER
TV
XM
POWER
XM
—
POWER
—
PHONO
PHONO
TUNER
TUNER
CD
CD
MULTI CH IN
MULTI CH IN
V-AUX/DOCK
V-AUX/DOCK
CBL/SAT
—
(*3)
CBL/SAT
POWER
MD/TAPE
(*1)
MD/TAPE
CD-R
CD-R
DTV
DTV
VCR 1
VCR 1
DVR/VCR 2
—
—
(CD area) (*4)
—
—
—
(MD/TAPE area) (*4)
(CD-R area) (*4)
—
(VCR 1 area) (*4)
DVR/VCR 2
(DVR/VCR 2 area) (*4)
DVD
DVD
(DVD area) (*4)
*1
You can turn on some components (including YAMAHA components) connected to this unit by connecting them to the AC
OUTLETS on the rear panel of this unit. Power control may not be synchronized with this unit depending on the component.
For details, refer to the operating instructions for the connected component.
*2 When the remote control code for your TV is set up for either DTV or PHONO (see page 103), you can turn on the power of your TV
without selecting an input source. The remote control code set up for DTV takes priority over the one for PHONO.
*3 When TUNER is selected as the input source, this unit plays the last station received before the unit was set in the standby mode.
*4 Playback can be started for any YAMAHA remote control-compatible MD recorder, CD player, CD recorder, DVD player, or DVD
recorder. When using macros to operate other components, you will need to program the play button on the input area of that
component (see page 105) or set a remote control code (see page 103).
108 En
01EN_00_RX-V1700_U.book Page 109 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
■ Programming macro operations
You can program your own macro and use the macro
programming feature to transmit several remote control
commands in sequence at the press of a button. Be sure to
set up remote control codes or perform learning operations
before programming the macro.
Note
“AGAIN” appears in the display window if you press a
button other than a macro button.
3
Notes
• The default macro is not cleared when a new macro is
programmed for a button. The default macro can be used again
when the programmed macro is cleared.
• It is not possible to add a new signal (macro step) to the default
macro. Programming a macro changes all macro contents.
• We do not recommend programming continuous operations
such as volume control in a macro.
1
Press the buttons for the functions you want
to include in the macro operation in
sequence.
You can set up to 10 steps (10 functions). After you
have set 10 steps, “FULL” appears and the remote
control automatically exits the macro mode. The
following example is for programming the following
procedure:
Step 1 (“MCR 1”): Press DVD.
Step 2 (“MCR 2”): Press AV POWER.
Step 3 (“MCR 3”): Press SLEEP.
Set the operation mode selector to AMP or
SOURCE and then press MACRO using a
ballpoint pen or similar object.
“MCR ?” appears in the display window on the
remote control.
POWER
POWER
TV
AV
2
XM
AMP
PHONO
STANDBY
TUNER
V-AUX/DOCK CBL/SAT
MCR 2: AV POWER
POWER
AUDIO SEL
SLEEP
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
MCR 3: SLEEP
3
SOURCE
DTV
VCR 1
TV
1
or
MCR 1: DVD
(U.S.A. model)
MACRO
AMP
Indicates the
number of macro
steps entered
TV
Note
Flashes alternately so you can
set the next step
If you do not complete each of the following steps within 30
seconds, the macro programming mode will be
automatically canceled. In this case, start over from step 1.
2
Press the macro button you want to use to
operate the macro.
The macro button name (ex. “M;DVD”) and the
selected component name (ex. “DVD”) appear
alternately in the display window on the remote
control.
STANDBY
POWER
XM
PHONO
Note
To change the selected input area, press SELECT k / n.
Pressing the input selector buttons will program a macro step,
whereas SELECT k / n only changes the selected input area.
4
Press MACRO again using a ballpoint pen or
similar object when the operation sequence
you want to program is complete.
Note
TUNER
V-AUX/DOCK CBL/SAT
DTV
ADVANCED
OPERATION
SOURCE
VCR 1
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
“ERROR” appears in the display window if you press more
than one button simultaneously.
(U.S.A. model)
109 En
01EN_00_RX-V1700_U.book Page 110 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
Clearing configurations
You can clear all changes made in each function set, such
as learned functions, macros, renamed input area names
and setup remote control ID.
■ Clearing function sets
1
Set the operation mode selector to AMP or
SOURCE and then press CLEAR by using a
ballpoint pen or similar object.
“CLEAR” appears in the display window.
y
Once you have cleared a learned function for a button, the
button reverts to the factory setting (or to the manufacturer
setting, if you have set remote control codes).
SOURCE
TV
CLEAR
or
Notes
• “L;ALL” and “FCTRY” may take about 30 seconds to
complete.
• “C;NG” appears in the display window if clearing was
unsuccessful. In this case start over from step 2.
• “ERROR” appears in the display window if you press a
button not indicated in the respective step, or if you press
more than one button simultaneously.
AMP
SOURCE
TV
Note
If you do not complete each of the following steps within 30
seconds, the clearing mode will be automatically canceled.
In this case, start over from step 1.
Press k / n to select the clear mode.
L;CD (etc.) (L; Name of an input area)
Clears all learned functions in the respective
input area. The name of a component is shown
after a semicolon (;). Press an input selector
button to select the input area.
L;AMP
Clears all learned functions for controlling the
amplifier functions of this unit.
L;ALL
Clears all learned functions.
M;ALL
Clears all programmed macros.
RNAME Clears all renamed source names.
FCTRY
Clears all remote functions and returns the
remote to the factory settings.
PRESET/CH
ENTER
A-E/CAT.
110 En
Press and hold CLEAR again for about 3
seconds.
“WAIT” appears in the display window. If clearing
was successful, “C;OK” appears in the display
window on the remote control.
CLEAR
AMP
2
3
01EN_00_RX-V1700_U.book Page 111 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
■ Clearing a learned function
You can clear the function learned for a certain button in
each control area.
1
3
Set the operation mode selector to AMP or
SOURCE and then press an input selector
button or to select the input area
containing the function you want to clear.
The selected component name appears in the display
window.
Press and hold CLEAR using a ballpoint pen
or similar object and then press the button
you want to clear for about 3 seconds.
“C;OK” appears in the display window if clearing
was successful. Once “C;OK” appears in the display
window on the remote control, release the ballpoint
pen or similar object used to press CLEAR to exit the
clearing mode. The remote control returns to the
learning mode.
AMP
XM
SOURCE
TV
PHONO
or
TUNER
V-AUX/DOCK CBL/SAT
DTV
AMP
VCR 1
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
LEARN
CLEAR
RENAME
(U.S.A. model)
SOURCE
2
y
(U.S.A. model)
TV
LEARN
4
Press LEARN again to exit.
Notes
• “C;NG” appears in the display window on the remote control if
clearing was unsuccessful. In this case, start over from step 2.
• “ERROR” appears in the display window if you press more than
one button simultaneously.
Notes
• Do not press and hold LEARN. If you hold it down for
more than 3 seconds, the remote control enters the remote
control code setting mode.
• If you do not complete each of the following steps within
30 seconds, the learning mode will be automatically
canceled. In this case, start over from step2.
111 En
ADVANCED
OPERATION
Press LEARN using a ballpoint pen or similar
object.
“LEARN” and the selected component name
(ex. “DVD”) appear alternately in the display
window.
• If you continuously want to clear another function, repeat
step 4.
• If you continuously want to clear another function for
another component, press SELECT k / n to select the
input area, then repeat step 4.
• Once you clear a learned function, the button reverts to the
factory setting (or to the manufacturer setting if you have
set remote control codes).
01EN_00_RX-V1700_U.book Page 112 Tuesday, June 27, 2006 9:37 AM
REMOTE CONTROL FEATURES
■ Clearing a macro function
You can clear the function programmed for a certain
macro button.
1
2
Set the operation mode selector to AMP or
SOURCE and then press MACRO using a
ballpoint pen or similar object.
“MCR ?” appears in the display window on the
remote control.
Press and hold CLEAR using a ballpoint pen
or similar object, then press the macro
button you want to clear for about 3 seconds.
“C;OK” appears in the display window on the remote
control if clearing was successful.
V-AUX/DOCK CBL/SAT
DTV
VCR 1
MD/TAPE
CD-R
DVR/VCR 2
DVD
AMP
SOURCE
TV
OFF
or
ON
MACRO
LEARN
CLEAR
RENAME
MACRO
(U.S.A. model)
AMP
y
SOURCE
• If you continuously want to clear another function, repeat
step 2.
• Once you clear a programmed function, the button reverts
to the factory setting (or to the manufacturer setting if you
have set remote control codes).
TV
Note
If you do not complete each of the following steps within 30
seconds, the macro programming mode will be
automatically canceled. In this case, start over from step 1.
3
Press MACRO again to exit the macro
programming mode.
Notes
• “C;NG” appears in the display window on the remote control if
clearing was unsuccessful. In this case, start over from step 2.
• “ERROR” appears in the display window on the remote control
if you press more than one button simultaneously.
112 En
01EN_00_RX-V1700_U.book Page 113 Tuesday, June 27, 2006 9:37 AM
USING MULTI-ZONE CONFIGURATION
USING MULTI-ZONE CONFIGURATION
This unit allows you to configure a multi-room audio system. The multi-zone configuration feature enables you to set this
unit to reproduce separate input sources in the main room, second room (Zone 2) and third room (Zone 3). You can
control this unit from the second or third room using the supplied remote control.
Only analog signals are sent to the second and third rooms. Any source you want to listen to in the second or third
room must be connected using the analog (AUDIO L/R) input jacks on this unit.
Connecting the Zone 2 and Zone 3 components
You need the following additional equipment to use the multi-room functions of this unit:
• An infrared signal receiver in the second and/or third room.
• An infrared emitter in the main room. This emitter transmits the infrared signals from the remote control in the second
and/or third room to the main room (to a CD player or DVD player, for example).
• An amplifier and speakers for the second and/or third room.
y
• You do not need an extra amplifier and speakers for the second and/or third room if you want to use the internal amplifiers of this unit.
• Since there are many possible ways to connect and use this unit in a multi-room configuration, we recommend that you consult with
your nearest authorized YAMAHA dealer or service center for the Zone 2 and Zone 3 connections that best meet your requirements.
REMOTE
REMOTE
IN
Infrared signal
receiver
OUT
REMOTE
IN
OUT
OUT
YAMAHA
component
YAMAHA
component
This unit
REMOTE
IN
To use an external amplifier in Zone 2 or Zone 3, connect the external amplifier to ZONE OUT terminals and select
“EXT” in “ZONE2 AMP” or “ZONE3 AMP” (see page 100).
ZONE 3 AUDIO OUT
ZONE 2 AUDIO OUT
SP OUT
Amplifier
Amplifier
MONITOR OUT
DVD player
(or other component)
VIDEO IN
AUDIO IN
This unit
MAIN
SYSTEM
Remote control
Remote control
Infrared signal
receiver
Infrared signal
receiver
ZONE 3
ZONE 2
Infrared emitter
Main room
(Main zone)
REMOTE OUT
Second room
(Zone 2)
Third room
(Zone 3)
REMOTE IN
REMOTE IN
Notes
• Adjust the Zone 2/Zone 3 volume by using the amplifier in the second/third room when “ZONE2 VOL” or “ZONE3 VOL” are set to
“FIX” (see page 99).
• To avoid unexpected noise, DO NOT use the Zone 2/Zone 3 feature with CDs encoded in DTS.
113 En
ADVANCED
OPERATION
■ Using external amplifiers
01EN_00_RX-V1700_U.book Page 114 Tuesday, June 27, 2006 9:37 AM
USING MULTI-ZONE CONFIGURATION
■ Using the internal amplifiers of this unit
IMPORTANT SAFETY NOTICE
The SP1 or SP2 speaker terminals of this Receiver should not be connected to a Passive Loudspeaker Selector Box or
more than one loudspeaker per channel.
Connection to a Passive Loudspeaker Selector Box or multiple speakers per channel could create an abnormally low
impedance load resulting in amplifier damage. See this owner’s manual for correct usage.
Compliance with minimum speaker impedance information for all channels must be maintained at all times. This
information is found on the back panel of your Receiver.
If you want to use one internal amplifier (SP1 or SP2) of this unit
Connect the Zone 2 or Zone 3 speakers directly to the SP1 or SP2 speaker terminals and select either “[SP1]” or “[SP2]”
for “ZONE2 AMP” or “ZONE3 AMP” (see page 100).
If you want to use two internal amplifiers (both SP1 and SP2) of this unit
Connect the Zone 2 or Zone 3 speakers directly to the SP1 and SP2 speaker terminals and select “BOTH” for “ZONE2
AMP” or “ZONE3 AMP” (see page 100).
R
+
SP1
– PRESENCE –
+
L
R
SP2
L
+
R
+
SURROUND BACK/
– BI-AMP –
+
L
SINGLE
–
Second room
(Zone 2)
Third room
(Zone 3)
This unit
Controlling Zone 2 or Zone 3
You can select the zone you want to control by using the
control buttons on the front panel or on the remote control.
2
Press ZONE CONTROLS on the front panel
repeatedly to select the zone you want to
control.
ZONE CONTROLS
■ Selecting Zone 2 or Zone 3
Front panel operations
1
Press ZONE 2 ON/OFF or ZONE 3 ON/OFF on
the front panel to individually turn on or off
Zone 2 or Zone 3.
Each time you press ZONE CONTROLS, the front
panel display changes as shown below, and the
indicator for the currently selected zone flashes for
approximately 5 seconds. However, no indicator
flashes when the main zone is selected.
ZONE2
ZONE3
ZONE ON/OFF
ZONE 2
ZONE 3
No indicator flashes when the main zone is
selected.
ZONE2
Controls the Zone 2 amplifier or tuner functions.
ZONE3
Controls the Zone 3 amplifier or tuner functions.
114 En
01EN_00_RX-V1700_U.book Page 115 Tuesday, June 27, 2006 9:37 AM
USING MULTI-ZONE CONFIGURATION
y
• You must complete this step within 5 seconds while the
selected zone flashes in the front panel display. Otherwise,
the currently selected zone mode is automatically
canceled. In this case, press ZONE CONTROLS again.
• The initial setting is ZONE2 when both Zone 2 and Zone 3
are turned on.
3
Refer to “Selecting the input source of Zone
2 or Zone 3”, “Adjusting the volume level of
Zone 2 or Zone 3”, “Adjusting the balance of
the speaker level in Zone 2 or Zone 3” or
“Adjusting the tonal quality of Zone 2 or
Zone 3” on page 116 to perform further
operations.
Remote control operations
1
Set the operation mode selector to AMP and
then press SELECT k repeatedly to select the
zone you want to control.
“ZONE 2” or “ZONE 3” is displayed in the display
window on the remote control.
■ Turning on or off Zone 2 and/or Zone 3
using the remote control
POWER and STANDBY on the remote control work
differently depending on the selected zone that appears in
the display window on the remote control.
• When the main zone, Zone 2 or Zone 3 mode is
selected , you can turn on the main zone, Zone 2 or
Zone 3 or set them to the standby mode individually.
• When the all mode is selected, pressing POWER turns
on the main zone, Zone 2 and Zone 3 simultaneously
and pressing STANDBY sets them to the standby mode
simultaneously.
Control mode
Display window
Turns on the main
zone only or sets it to
the standby mode.
Zone 2 mode
“ZONE 2” or “2;name
of the selected input
area”
Turns on Zone 2 or
sets it to the standby
mode.
Zone 3 mode
“ZONE 3” or “3;name
of the selected input
area”
Turns on Zone 3 or
sets it to the standby
mode.
“ALL”
POWER: turns on
the main zone, Zone
2 and Zone 3.
STANDBY: sets the
main zone, Zone 2
and Zone 3 to the
standby mode.
SELECT
All mode
TV
Notes
or
2
3
Refer to “Selecting the input source of Zone
2 or Zone 3”, “Adjusting the volume level of
Zone 2 or Zone 3”, “Adjusting the balance of
the speaker level in Zone 2 or Zone 3” or
“Adjusting the tonal quality of Zone 2 or
Zone 3” on page 116 to perform further
operations.
Press SELECT k / n to exit from the
Zone 2/Zone 3 mode.
Note
The input source of Zone 2 and the source available for
recording are always the same.
• When the remote control is in the main zone mode, “MAIN”
appears for a few seconds when POWER or STANDBY is
pressed.
• “ALL” appears in the display window on the remote control
only when SELECT n is pressed.
■ Selecting the input source of Zone 2 or
Zone 3
Rotate the INPUT selector on the front panel (or
set the operation mode selector to AMP and then
press one of the input selector buttons on the
remote control) to select the input source of the
selected zone.
If the remote control is used to select the input source, “2:
name of the selected input source” or “3: name of the
selected input source” is displayed in the display window
on the remote control when Zone 2 or Zone 3 is selected
respectively.
115 En
ADVANCED
OPERATION
Name of the selected
input area
Main zone
mode
AMP
SOURCE
POWER
and
STANDBY
01EN_00_RX-V1700_U.book Page 116 Tuesday, June 27, 2006 9:37 AM
USING MULTI-ZONE CONFIGURATION
■ Adjusting the balance of the speaker
level in Zone 2 or Zone 3
INPUT
Press TONE CONTROL repeatedly to select
“BALANCE” and then rotate PROGRAM on the
front panel to adjust the balance of the front left
and right speaker level of the selected zone.
or
TONE
CONTROL
XM
AMP
PHONO
SOURCE
TUNER
V-AUX/DOCK CBL/SAT
CD
MULTI CH IN
MD/TAPE
CD-R
DVR/VCR 2
DVD
PROGRAM
TV
DTV
VCR 1
(U.S.A. model)
• Select TUNER as the input source to use the TUNER
features in the selected zone. For details about the
TUNER operations, see “FM/AM TUNING” on
page 54.
• Select XM as the input source to use the XM Satellite
Radio features in the selected zone. For details about
the XM Satellite Radio operations, see “XM
SATELLITE RADIO TUNING” on page 61.
■ Adjusting the tonal quality of Zone 2 or
Zone 3
Set the operation mode selector to AMP and then
press CH +/– on the remote control to adjust the
high-frequency response (TREBLE) or
TV VOL +/– to adjust the low-frequency response
(BASS) respectively.
+
Note
TV VOL
The selected input source is shared across all zones.
–
y
AMP
You must complete this step within 5 seconds while the selected
zone flashes in the front panel display. Otherwise, the currently
selected zone mode is automatically canceled. In this case, press
ZONE CONTROLS on the front panel again.
SOURCE
BASS
TV
+
CH
■ Adjusting the volume level of Zone 2 or
Zone 3
–
TREBLE
Rotate VOLUME on the front panel (or press
VOLUME +/– on the remote control) to adjust the
volume level of the selected zone.
VOLUME
+
or
VOLUME
–
y
Press MUTE on the remote control to mute the sound output to
the selected zone.
Note
When you use the external amplifiers in Zone 2 or Zone 3,
VOLUME +/– can be used only when ZONE2 VOL” or “ZONE3
VOL” is set to “VAR” in “ZONE SET” (see page 99).
116 En
y
You can also adjust the tonal quality of Zone 2 or Zone 3 by using
TONE CONTROL on the front panel. For details, see “Adjusting
the tonal quality” on page 50.
Note
Check that “ZONE 2” or “ZONE 3” is displayed in the display
window of the remote control before you adjust the tonal quality
of the corresponding zone (see page 115).
01EN_00_RX-V1700_U.book Page 117 Tuesday, June 27, 2006 9:37 AM
ADVANCED SETUP
ADVANCED SETUP
This unit has additional menus that are displayed in the front panel display. The advanced setup menu offers additional
operations to adjust and customize the way this unit operates. Change the initial settings (indicated in bold under each
parameter) to reflect the needs of your listening environment.
Notes
• The settings you make are reflected next time you press MASTER ON/OFF inward to the ON position to turn on this unit (see
page 31).
• Only MASTER ON/OFF, STRAIGHT and the PROGRAM selector are effective while you are using the advanced setup menu.
• All the other operations cannot be made while you are using the advanced setup menu.
• The advanced setup menu is only available in the front panel display.
Using ADVANCED SETUP
3
(U.S.A. model)
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
Rotate the PROGRAM selector on the front
panel to select the parameter you want to
adjust.
The name of the selected parameter appears in the
front panel display.
See page 118 for a complete list of available
parameters.
NIGHT
EDIT
DISPLAY
SEARCH MODE
CATEGORY
INPUT
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
PHONES
S VIDEO
ZONE 2
ZONE 3
L
R
VIDEO
AUDIO
OPTICAL
VIDEO AUX
ON
OFF
MASTER
1-2,5
PROGRAM
2,4
Currently selected
parameter
Press MASTER ON/OFF on the front panel to
release it outward to the OFF position to turn
off this unit.
Currently selected
parameter setting
SPEAKER IMP.
8 MIN
MASTER
2
4
Press and hold STRAIGHT on the front panel
and then press MASTER ON/OFF inward to
the ON position to turn on this unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
Press STRAIGHT on the front panel
repeatedly to change the selected parameter
setting.
STRAIGHT
EFFECT
STRAIGHT
EFFECT
While holding
down
5
MASTER
Press MASTER ON/OFF on the front panel to
release it outward to the OFF position to save
the new setting and turn off this unit.
MASTER
y
The settings you made are reflected next time you turn on
this unit.
117 En
ADVANCED
OPERATION
1
3
01EN_00_RX-V1700_U.book Page 118 Tuesday, June 27, 2006 9:37 AM
ADVANCED SETUP
■ Speaker impedance
SPEAKER IMP.
Use this feature to set the speaker impedance of this unit
so that it matches that of your speakers.
Choices: 8ΩMIN, 6ΩMIN
• Select “8ΩMIN” to set the speaker impedance to 8 Ω .
• Select “6ΩMIN” to set the speaker impedance to 6 Ω .
SPEAKER
IMP.
Speaker
Front
8ΩMIN
Impedance level
The impedance of each
speaker must be 8 Ω or
higher.
The impedance of each
speaker must be 8 Ω or
higher.
Surround back
Front
6ΩMIN
The impedance of each
speaker must be 4 Ω or
higher.
RC AMP ID
Use this feature to set the AMP ID of this unit for remote
control recognition (see page 104).
Choices: ID1, ID2
• Select “ID1” when the remote control AMP ID library
code is set to “2001”.
• Select “ID2” when the remote control AMP ID library
code is set to “2002”.
Center
Surround
The impedance of each
speaker must be 6 Ω or
higher.
Surround back
■ User presets
USER PRESET
Use this feature to reset all the parameters of this unit to
the initial factory settings (see page 130).
Choices: CANCEL, RESET
• Select “CANCEL” not to reset any parameters of this
unit.
• Select “RESET” to reset the parameters of this unit.
Notes
• This setting completely resets all the parameters of this unit
including the “SET MENU” parameters. However, the
advanced setup menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on
this unit.
■ Remote sensor REMOTE SENSOR
Use this feature to activate or deactivate the signalreceiving capability of the remote control sensor on the
front panel of this unit.
Choices: ON, OFF
• Select “ON” if you want to activate the signalreceiving capability of the remote control sensor.
• Select “OFF” if you want to deactivate the signalreceiving capability of the remote control sensor.
Note
We recommend setting the parameter to “ON” in most cases.
118 En
WAKE ON RS232C
Use this feature to set this unit to transmit data via the RS232C interface when this unit is in the standby mode.
Choices: YES, NO
Initial setting:
[U.S.A. and Canada models]: YES
[Other models]: NO
• Select “YES” to set this unit to transmit data via the
RS-232C interface.
• Select “NO” to set this unit not to transmit data via the
RS-232C interface.
■ Remote control AMP ID
Center
Surround
■ Wake on RS-232C access
Note
You need to set the corresponding remote control AMP library
code for the remote control (see page 104).
■ Remote control TUNER ID
RC TUNER ID
Use this feature to set the TUNER ID of this unit for
remote control recognition (see page 121).
Choices: ID1, ID2
• Select “ID1” when the remote control TUNER ID
library code is set to “2602”.
• Select “ID2” when the remote control TUNER ID
library code is set to “2603”.
Note
You need to set the corresponding remote control TUNER library
code for the remote control (see page 121).
■ Remote control XM ID RC XM ID
(U.S.A. and Canada models only)
Use this feature to set the XM ID of this unit for remote
control recognition (see page 121).
Choices: ID1, ID2
• Select “ID1” when the remote control XM ID library
code is set to “2604”.
• Select “ID2” when the remote control XM ID library
code is set to “2605”.
Note
You need to set the corresponding remote control XM library
code for the remote control (see page 121).
01EN_00_RX-V1700_U.book Page 119 Tuesday, June 27, 2006 9:37 AM
ADVANCED SETUP
■ Tuner frequency step TUNER FRQ STEP
(Asia and General models only)
Use this feature to set the tuner frequency step according
to the frequency spacing in your area.
Choices: AM10/FM100, AM9/FM50
• Select “AM10/FM100” for North, Central and South
America.
• Select “AM9/FM50” for all other areas.
■ Bi-AMP BI-AMP
Use to activate or deactivate the bi-AMP function.
Choices: ON, OFF
• Select “ON” if you want to activate the bi-AMP
function.
• Select “OFF” if you want to deactivate the bi-AMP
function.
Setting remote control ID
When using multiple YAMAHA receivers/amplifiers, you
may be able to operate the other components
simultaneously with the default code setting. In this case,
set one of the alternative codes to operate this unit
separately.
■ Setting remote control AMP ID
1
Set the operation mode selector to AMP or
SOURCE.
AMP
SOURCE
or
TV
Note
When BI-AMP is set to ON, the SURROUND BACK terminals
cannot be used to connect surround back speakers in that the
SURROUND BACK terminals are already used for the bi-AMP
connection (see page 17).
AMP
2
■ Video reset
VIDEO RESET
Use to initialize the parameter settings for “DISPLAY
SET” in “OPTION MENU” (see page 97).
Choices: YES, CANCEL
SOURCE
TV
Press and hold LEARN for about 3 seconds
using a ballpoint pen or similar object and
then press l / h repeatedly until “L;AMP”
appears in the display window on the remote
control.
PRESET/CH
Note
LEARN
ENTER
The parameter setting for “DIMMER”, “SHORT MESSAGE”,
“ON SCREEN” and “FL SCROLL” is not initialized (see
page 97).
ADVANCED
OPERATION
A-E/CAT.
Notes
• Be sure to press and hold LEARN for at least 3 seconds,
otherwise the learning process will start.
• If you do not complete each of the following steps within
30 seconds, the setting mode will be automatically
canceled. In this case, start over from step 1.
3
Press ENTER.
The four-digit code set for the selected input area
appears in the display window on the remote control.
PRESET/CH
ENTER
A-E/CAT.
119 En
01EN_00_RX-V1700_U.book Page 120 Tuesday, June 27, 2006 9:37 AM
ADVANCED SETUP
4
■ Setting remote control tuner ID or XM ID
Press the numeric buttons to enter the
four-digit remote control code for the input
area you want to use.
CLASSICAL
LIVE/CLUB
ENTERTAIN
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
7
8
1
MOVIE
Set the operation mode selector to AMP or
SOURCE and then press TUNER or XM on
the remote control to select the tuner or XM
to change the remote control ID.
AMP
TUNER
SOURCE
9
0
TV
or
or
Remote control AMP codes
Select one of the following codes to set the remote control
AMP code for the input area you want to use.
AMP
XM
SOURCE
TV
AMP library
code (remote
control
setting)
Function
Remote
control AMP
ID
2001
(initial setting)
To operate this unit using the
default code.
ID1
(initial setting)
2002
To operate this unit using an
alternative code.
ID2
2
Press and hold LEARN for about 3 seconds
using a ballpoint pen or similar object and
then press l / h repeatedly until “L;TUN”
and “TUNER”, or “L;TUN” and “XM”
alternately appear in the display window on
the remote control.
Note
PRESET/CH
You need to set the corresponding remote control AMP ID
(see page 118).
LEARN
ENTER
A-E/CAT.
5
Press ENTER to set the number.
“OK” appears in the display window if setting was
successful.
“NG” appears in the display window if the setting
was unsuccessful. In this case, start over from step 1.
Notes
• Be sure to press and hold LEARN for at least 3 seconds,
otherwise the learning process will start.
• If you do not complete each of the following steps within
30 seconds, the setting mode will be automatically
canceled. In this case, start over from step 1.
PRESET/CH
ENTER
3
A-E/CAT.
6
Press ENTER.
The four-digit code set for the selected input area
appears in the display window on the remote control.
Press LEARN again to exit from the setup
mode.
PRESET/CH
LEARN
ENTER
A-E/CAT.
120 En
01EN_00_RX-V1700_U.book Page 121 Tuesday, June 27, 2006 9:37 AM
ADVANCED SETUP
4
Press the numeric buttons to enter the
four-digit remote control code for the input
area you want to use.
CLASSICAL
LIVE/CLUB
ENTERTAIN
1
2
3
4
STEREO
SUR. DECODE
SELECT
EXTD SUR.
5
6
7
8
9
0
5
MOVIE
Press ENTER to set the number.
“OK” appears in the display window if setting was
successful.
“NG” appears in the display window if the setting
was unsuccessful. In this case, start over from step 1.
PRESET/CH
ENTER
A-E/CAT.
Remote control tuner codes
Select one of the following codes to set the remote control
tuner code for the input area you want to use.
Tuner library
code (remote
control
setting)
Function
Remote
control
tuner ID
2602
(initial setting)
To operate this unit using the
default code.
ID1
(initial setting)
2603
To operate this unit using an
alternative code.
ID2
6
Press LEARN again to exit from the setup
mode.
LEARN
Remote control XM codes
Select one of the following codes to set the remote control
XM code for the input area you want to use.
control
setting)
Function
ADVANCED
OPERATION
XM library
code (remote
Remote
control XM
ID
2604
(initial setting)
To operate this unit using the
default code.
ID1
(initial setting)
2605
To operate this unit using an
alternative code.
ID2
Note
You need to set the corresponding remote control tuner ID
or XM ID (see page 118).
121 En
01EN_00_RX-V1700_U.book Page 122 Tuesday, June 27, 2006 9:37 AM
TROUBLESHOOTING
TROUBLESHOOTING
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
YAMAHA dealer or service center.
■ General
Problem
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
No sound
122 En
Cause
Remedy
See
page
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
—
The speaker impedance setting is
incorrect.
Set the speaker impedance to match your speakers.
30
The protection circuitry has been
activated.
Make sure that all speaker wire connections on this
unit and on all speakers are secure and that the wire
for each connection does not touch anything other
than its respective connection.
14
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to the standby mode, disconnect the
power cable, plug it back in after 30 seconds and then
use it normally.
—
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
21-27
The optimizer microphone is connected.
Disconnect the optimizer microphone.
36
Audio input jack select is set to “HDMI”,
“COAX/OPT” or “ANALOG”.
Set Audio input jack select to “AUTO”.
40
Audio input jack select is set to
“ANALOG” while playing a source
encoded in Dolby Digital or DTS.
Set Audio input jack select to “AUTO” or
“COAX/OPT”.
40
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or the input selector
buttons on the remote control).
Speaker connections are not secure.
Secure the connections.
14
The volume is turned down.
Turn up the volume.
—
The sound is muted.
Press MUTE or VOLUME +/– on the remote control
to resume audio output and then adjust the volume.
41
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by this
unit.
—
The HDMI components connected to this
unit do not support the HDCP copy
protection standards.
Connect HDMI components that support the HDCP
copy protection standards.
19
“SUPPORT AUDIO” is set to “OTHER”
and “HDMI” audio signals are not being
played back on this unit.
Set “SUPPORT AUDIO” to “RX-V1700” in
“MANUAL SETUP”.
93
38, 41
01EN_00_RX-V1700_U.book Page 123 Tuesday, June 27, 2006 9:37 AM
TROUBLESHOOTING
Problem
No picture
Cause
Remedy
See
page
Set “V CONV.” to “ON” or connect your source
components in the same way as you connect your
video monitor to this unit.
97
“SHORT MESSAGE” is set to “OFF”.
Set “SHORT MESSAGE” to “ON”.
98
“GRAY BACK” is set to “OFF”.
Set “GRAY BACK” to “AUTO”.
97
“V CONV.” is set to “OFF”.
Set “V CONV.” to “ON”.
97
The output and input for the picture are
connected to different types of video
jacks.
Non-standard video signals are input.
Short message
displays do not
appears in the video
monitor
The signals input at the HDMI IN1 or
HDMI IN2 jack are being output at the
HDMI OUT jack.
Video signals in the progressive format or
HDTV video signals are being input.
The sound suddenly
goes off.
30, 118
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned off this unit.
Turn on this unit, and play the source again.
—
The sound is muted.
Press MUTE or VOLUME +/– on the remote control
to resume audio output.
41
Sound is heard from
the speaker on one
side only.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
14
Incorrect settings in “SP LEVEL”.
Adjust the “SP LEVEL” settings.
90
Only the center
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound is heard
from the center
speaker.
“CENTER SP” in “SET MENU” is set to
“NONE”.
Set “CENTER SP” to “SML” or “LRG”.
88
One of the HiFi DSP programs (except for
“7ch Stereo”) has been selected.
Try another sound field program.
45
No sound from the
presence speakers
The sound field programs are turned off.
Press STRAIGHT to turn them on.
49
You are using a source or program
combination that does not output sound
from all channels.
Try another sound field program.
38
No sound is heard
from the surround
speakers.
“SUR. L/R SP” in “SET MENU” is set to
“NONE”.
Set “SUR. L/R SP” to “SML” or “LRG”.
88
This unit is in the “STRAIGHT” mode
and a monaural source is being played
back.
Press STRAIGHT on the front panel so that
“STRAIGHT” disappears from the front panel
display.
49
No sound is heard
from the subwoofer.
“LFE/BASS OUT” in “SET MENU” is
set to “FRONT” when a Dolby Digital or
DTS signal is being played.
Set “LFE/BASS OUT” to “SWFR” or “BOTH”.
87
“LFE/BASS OUT” in “SET MENU” is
set to “SWFR” or “FRONT” when a 2channel source is being played.
Set “LFE/BASS OUT” to “BOTH”.
87
The source does not contain lowfrequency signals.
123 En
ADDITIONAL
INFORMATION
Check that the speaker impedance setting is correct.
The protection circuitry has been activated
because of a short circuit, etc.
01EN_00_RX-V1700_U.book Page 124 Tuesday, June 27, 2006 9:37 AM
TROUBLESHOOTING
Problem
No sound is heard
from the surround
back speakers.
Cause
Remedy
See
page
“SUR. L/R SP” in “SET MENU” is set to
“NONE” and “SB L/R SP” is
automatically set to “NONE”.
Set “SUR. L/R SP” and “SB L/R SP” to a setting
other than “NONE”.
88
“SB L/R SP” in “SET MENU” is set to
“NONE”.
Set “SB L/R SP” to a setting other than “NONE”.
89
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator in
the front panel
display does not light
up.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operating
instructions for your component.
—
Audio input jack select is set to
“ANALOG”.
Set Audio input jack select to “AUTO”.
40
A humming sound is
heard.
Incorrect cable connections.
Connect the audio cables firmly. If the problem
persists, the cables may be defective.
—
No connection from the turntable to the
GND terminal.
Connect the grounding cable of your turntable to the
GND terminal of this unit.
24
The volume level is
low while a record is
being played.
The record is being played on a turntable
with an MC cartridge.
Connect your turntable to this unit through an MChead amplifier.
24
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the AUDIO
OUT (REC) jacks of this unit is turned
off.
Turn on the power of the component.
—
The sound effect
cannot be recorded.
It is not possible to record the sound effect
with a recording component.
A source cannot be
recorded by a digital
recording component
connected to the
DIGITAL OUTPUT
jack.
The source component is not connected to
the DIGITAL INPUT jacks of this unit.
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT (REC)
jacks.
The source component is not connected to
the analog AUDIO IN jacks of this unit.
Connect the source component to the analog AUDIO
IN jacks.
24
The sound field
parameters and some
other settings of this
unit cannot be
changed.
“MEMORY GUARD” in “SET MENU”
is set to “ON”.
Set “MEMORY GUARD” to “OFF”.
98
124 En
Connect the source component to the DIGITAL
INPUT jacks.
22, 24
Some components cannot record Dolby
Digital or DTS sources.
01EN_00_RX-V1700_U.book Page 125 Tuesday, June 27, 2006 9:37 AM
TROUBLESHOOTING
Problem
Cause
Remedy
See
page
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the power cable from the AC wall outlet
and then plug it in again after about 30 seconds.
—
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short-circuited.
Make sure all speaker cables are connected correctly.
14
There is noise
interference from
digital or radio
frequency equipment.
This unit is too close to the digital or highfrequency equipment.
Move this unit further away from such equipment.
—
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
This unit suddenly
enters the standby
mode.
The internal temperature becomes too
high and the overheat protection circuitry
has been activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
■ Tuner
Problem
FM stereo reception is
noisy.
FM
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Remedy
See
page
Check the antenna connections.
28
Try using a high-quality directional FM
antenna.
—
Use the manual tuning method.
56
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multi-path interference.
Adjust the antenna position to eliminate
multi-path interference.
—
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is too weak.
Use a high-quality directional FM antenna.
—
Use the manual tuning method.
56
Previously preset
stations can no longer
be tuned into.
This unit has been disconnected for a
long period.
Preset the stations again.
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections
and orient it for the best reception.
—
Use the manual tuning method.
56
There are continuous
crackling and hissing
noises.
Noises can result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
—
There are buzzing and
whining noises.
A TV set is being used nearby.
Move this unit away from the TV set.
—
57, 58
125 En
ADDITIONAL
INFORMATION
AM
Cause
01EN_00_RX-V1700_U.book Page 126 Tuesday, June 27, 2006 9:37 AM
TROUBLESHOOTING
■
XM Satellite Radio (U.S.A. and Canada models only)
If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel
display. In this case, read the cause and follow the corresponding remedies.
Status message
Cause
Remedy
See
page
CHECK ANTENNA
The XM Passport and XM Passport Home
Dock are not connected to the XM jack of
this unit or do not work properly.
Check XM Passport and XM Passport Home Dock
connections and orient for the best reception level.
61
UPDATING
The XM user encryption code is being
updated.
Wait until the encryption code is updated.
—
NO SIGNAL
The signal is too weak.
Adjust the orientation of the XM Passport System for
the best reception level.
61
LOADING
It takes longer than four seconds for audio
or text data to be decoded.
Wait until the decoding process has finished.
—
OFF AIR
The XM Satellite Radio channel you
selected is not currently broadcasting any
signals.
Check the channel number again or select another
XM Satellite Radio channel.
—
<XM> - - -
The Channel Station ID (SID) is no longer
available.
- - -
No artist name or song title is available.
Select another channel category by pressing
CATEGORY on the front panel (or A-E/CAT. j / i on
the remote control) repeatedly.
67
/
- - -
<CAT> - - -
126 En
No channels are available for the selected
category.
01EN_00_RX-V1700_U.book Page 127 Tuesday, June 27, 2006 9:37 AM
TROUBLESHOOTING
■ Remote control
Problem
The remote control
does not work or
function properly.
Wrong distance or angle.
See
page
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel.
9
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
The batteries are weak.
Replace all batteries.
9
The operation mode selector is set
incorrectly.
Set the operation mode selector correctly.
When operating this unit, set it to the AMP position.
When operating the component selected by the input
selector button, set it to the SOURCE position.
When operating the TV set in the DTV or PHONO
area, set it to the TV position.
—
Set the remote control code correctly using
“LIST OF REMOTE CONTROL CODES” at the end
of this manual.
103
Try setting another code of the same manufacturer
using “LIST OF REMOTE CONTROL CODES” at
the end of this manual.
103
The remote control code was not correctly
set.
The remote control
does not learn new
functions.
Remedy
Cause
—
The library code of the remote control and
the remote control ID of this unit do not
match.
Match the remote control ID of this unit with the
corresponding remote control library code.
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
Program the necessary functions independently into
the programmable buttons using the Learn feature.
The batteries of this remote control and/or
the other remote control are too weak.
Replace the batteries.
The distance between the two remote
controls is too much or too little.
Place the remote controls at the proper distance.
The signal coding or modulation of the
other remote control is not compatible
with this remote control.
Learning is not possible.
Memory capacity is full.
Delete other unnecessary functions to make room for
the new functions.
110
Remedy
See
page
104, 118
105
9
105
—
Error message
Cause
DEVICE OVER
The number of the connected HDMI
components is over the limit.
Reduce the number of the connected HDMI
components.
—
HDCP ERROR
HDCP authentication failed.
Check that the connected HDMI components support
the HDCP copy protection standards.
—
127 En
ADDITIONAL
INFORMATION
■ HDMI
01EN_00_RX-V1700_U.book Page 128 Tuesday, June 27, 2006 9:37 AM
TROUBLESHOOTING
■ iPod
Note
In case of a transmission error without a status message appearing in the front panel and in the OSD, check the connection to your iPod
(see page 27).
Status message
Loading...
Cause
Remedy
See
page
This unit is in the middle of recognizing
the connection with your iPod.
This unit is in the middle of acquiring
song lists from your iPod.
Connect error
There is a problem with the signal path
from your iPod to this unit.
Turn off this unit and reconnect the YAMAHA iPod
universal dock to the DOCK terminal of this unit.
27
Try resetting your iPod.
—
Only iPod (Click and Wheel), iPod nano, and iPod
mini are supported.
—
Unknown type
The iPod being used is not supported by
this unit.
iPod connected
Your iPod is properly stationed in a
YAMAHA iPod universal dock (such as
the YDS-10, sold separately) connected to
the DOCK terminal of this unit, and the
connection between your iPod and this
unit is complete.
Disconnected
Your iPod was removed from a YAMAHA
iPod universal dock (such as YDS-10 sold
separately) connected to the DOCK
terminal of this unit.
Station your iPod back in a YAMAHA iPod universal
dock (such as YDS-10 sold separately) connected to
the DOCK terminal of this unit.
27
Unable to play
This unit cannot play back the songs
currently stored on your iPod.
Check that the songs currently stored on your iPod
are playable.
—
Store some other playable music files on your iPod.
—
■ AUTO SETUP
Before AUTO SETUP
Error message
Connect MIC!
Unplug HP!
128 En
Cause
Optimizer microphone is not connected.
Headphones are connected.
Remedy
See
page
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
32
Unplug the headphones.
—
01EN_00_RX-V1700_U.book Page 129 Tuesday, June 27, 2006 9:37 AM
TROUBLESHOOTING
During AUTO SETUP
Error message
Cause
Remedy
See
page
E-1:NO FRONT SP
Front L/R channel signals are not detected.
Check the front L/R speaker connections.
14
E-2:NO SURR.SP
A surround channel signal is not detected.
Check the surround speaker connections.
14
E-3:NO PRNS. SP
A presence channel signal is not detected.
Check the presence speaker connections.
14
E-4:SBR->SBL
Only right surround back channel signal is
detected.
Connect the surround back speaker to the
LEFT SURROUND BACK SPEAKERS
terminal if you only have one surround
back speaker.
14
Background noise is too loud.
Try running “AUTO SETUP” in a quiet
environment.
—
Turn off noisy electric equipment like air
conditioners or move them away from the
optimizer microphone.
—
E-5:NOISY
E-6:CHECK SUR.
Surround back speakers are connected,
though surround L/R speakers are not.
Connect surround speakers when you use
surround back speakers.
14
E-7:NO MIC
The optimizer microphone was unplugged
during the “AUTO SETUP” procedure.
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
32
The optimizer microphone does not detect
test tones.
Check the microphone setting.
32
Check the speaker connections and
placement.
14
E-8:NO SIGNAL
E-9:USER CANCEL
The “AUTO SETUP” procedure was
cancelled due to user activity.
Run “AUTO SETUP” again.
E-10:INTERNAL ERROR
An internal error occurred.
Run “AUTO SETUP” again.
32
32
After AUTO SETUP
Warning message
W-1:OUT OF PHASE
Cause
Remedy
See
page
Check the speaker connections for proper
polarity (+ or –).
W-2:OVER 24m (80ft)
The distance between the speaker and the
listening position is over 24 m (80 ft).
Bring the speaker closer to the listening
position.
—
W-3:LEVEL ERROR
The difference of volume level among
speakers is excessive.
Readjust the speaker installation so that all
speakers are set in locations with similar
conditions.
—
Check the speaker connections.
14
Use speakers of similar quality.
—
Adjust the output volume of the subwoofer.
32
14
Notes
•
•
•
•
If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “AUTO SETUP” again.
If warning “W-1” appears, corrections are made, but they may not be optimal.
If warning “W-2” or “W-3” appears, no corrections are made.
If error “E-10” occurs repeatedly, please contact a qualified YAMAHA service center.
129 En
ADDITIONAL
INFORMATION
Speaker polarity is not correct. This
message may appear depending on the
speakers even when the speakers are
connected correctly.
01EN_00_RX-V1700_U.book Page 130 Tuesday, June 27, 2006 9:37 AM
RESETTING THE SYSTEM
RESETTING THE SYSTEM
Use this feature to reset all the parameters of this unit to the initial factory settings.
Notes
• This procedure completely resets all the parameters of this unit including the “SET MENU” parameters. However, the advanced setup
menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on this unit.
y
To cancel the initialization procedure at any time without making any changes, press MASTER ON/OFF on the front panel to release it
outward to the OFF position.
(U.S.A. model)
3
Rotate the PROGRAM selector on the front
panel to select “PRESET”.
PURE DIRECT
VOLUME
AUDIO
SELECT
TONE
CONTROL
A/B/C/D/E
PRESET/TUNING/CH
PRESET/
TUNING
MEMORY
FM/AM
MAN'L/AUTO FM
TUNING
MODE
ENHANCER
NIGHT
EDIT
INPUT
DISPLAY
SEARCH MODE
CATEGORY
ZONE ON/OFF
STRAIGHT
MAIN ZONE
ZONE CONTROLS
MULTI ZONE
EFFECT
YPAO
ON/OFF
PROGRAM
OPTIMIZER
MIC
SILENT CINEMA
S VIDEO
ZONE 2
ZONE 3
L
R
VIDEO
AUDIO
OPTICAL
PROGRAM
PHONES
VIDEO AUX
ON
OFF
MASTER
1-2,5
1
3
2,4
USERPRESET
Press MASTER ON/OFF on the front panel to
release it outward to the OFF position to turn
off this unit.
CANCEL
4
Press STRAIGHT on the front panel
repeatedly to select “RESET”.
MASTER
STRAIGHT
2
Press and hold STRAIGHT on the front panel
and then press MASTER ON/OFF inward to
the ON position to turn on this unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
STRAIGHT
EFFECT
EFFECT
USERPRESET
While holding
down
RESET
MASTER
y
Select “CANCEL” to cancel the initialization procedure
without making any changes.
5
Press MASTER ON/OFF on the front panel to
release it outward to the OFF position to
confirm your selection and turn off this unit.
MASTER
130 En
01EN_00_RX-V1700_U.book Page 131 Tuesday, June 27, 2006 9:37 AM
GLOSSARY
GLOSSARY
■ Bi-amplification connection
■ Dolby Digital
A bi-amplification connection uses two amplifiers for a
speaker. One amplifier is connected to the woofer section
of a loudspeaker while the other is connected to the
combined mid and tweeter section. With this arrangement
each amplifier operates over a restricted frequency range.
This restricted range presents each amplifier with a much
simpler job and each amplifier is less likely to influence
the sound in some way. The internal crossover of the
speaker consists of a LPF (low pass filter) and a HPF (high
pass filter). As its name implies, the LPF passes
frequencies below a cutoff and rejects frequencies above
the cutoff frequency. Likewise, the HPF passes
frequencies above its cutoff.
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (front L/R and center), and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (Low Frequency Effect), the system
has a total of 5.1-channels (LFE is counted as 0.1
channel). By using 2-channel stereo for the surround
speakers, more accurate moving sound effects and
surround sound environment are possible than with Dolby
Surround. The wide dynamic range from maximum to
minimum volume reproduced by the 5 full-range channels
and the precise sound orientation generated using digital
sound processing provide listeners with unprecedented
excitement and realism. With this unit, any sound
environment from monaural up to a 5.1-channel
configuration can be freely selected for your enjoyment.
■ Component video signal
With the component video signal system, the video signal
is separated into the Y signal for the luminance and the PB
and PR signals for the chrominance. Color can be
reproduced more faithfully with this system because each
of these signals is independent. The component signal is
also called the “color difference signal” because the
luminance signal is subtracted from the color signal. A
monitor with component input jacks is required in order to
output component signals.
■ Composite video signal
With the composite video signal system, the video signal
is composed of three basic elements of a video picture:
color, brightness and synchronization data. A composite
video jack on a video component transmits these three
elements combined.
■ Dialogue normalization
Dolby Digital EX creates 6 full-bandwidth output
channels from 5.1-channel sources. This is done using a
matrix decoder that derives 3 surround channels from the
2 in the original recording. For the best results, Dolby
Digital EX should be used with movie sound tracks
recorded with Dolby Digital Surround EX. With this
additional channel, you can experience more dynamic and
realistic moving sound especially with scenes with “flyover” and “fly-around” effects.
■ Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround sources.
This new technology enables a discrete 5-channel
playback with 2 front left and right channels, 1 center
channel, and 2 surround left and right channels instead of
only 1 surround channel for conventional Pro Logic
technology. There are three modes available: “Music
mode” for music sources, “Movie mode” for movie
sources and “Game mode” for game sources.
■ Dolby Pro Logic IIx
Dolby Pro Logic IIx is a new technology enabling discrete
multi-channel playback from 2-channel or multi-channel
sources. There are three modes available: “Music mode”
for music sources, “Movie mode” for movie sources (for
2-channel sources only) and “Game mode” for game
sources.
131 En
ADDITIONAL
INFORMATION
Dialogue Normalization is a feature of Dolby Digital or
DTS, which is used to keep the programs at the same
average listening level so the user does not have to change
the volume control between Dolby Digital or DTS
programs.
■ Dolby Digital EX
01EN_00_RX-V1700_U.book Page 132 Tuesday, June 27, 2006 9:37 AM
GLOSSARY
■ Dolby Surround
■ HDMI
Dolby Surround uses a 4-channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range. Dolby Surround is
widely used with nearly all video tapes and laser discs,
and in many TV and cable broadcasts as well. The Dolby
Pro Logic decoder built into this unit employs a digital
signal processing system that automatically stabilizes the
volume on each channel to enhance moving sound effects
and directionality.
HDMI (High-Definition Multimedia Interface) is the first
industry-supported, uncompressed, all-digital audio/video
interface. Providing an interface between any source (such
as a set-top box or AV receiver) and an audio/video
monitor (such as a digital television), HDMI supports
standard, enhanced or high-definition video as well as
multi-channel digital audio using a single cable. HDMI
transmits all ATSC HDTV standards and supports 8channel digital audio, with bandwidth to spare to
accommodate future enhancements and requirements.
When used in combination with HDCP (High-bandwidth
Digital Content Protection), HDMI provides a secure
audio/video interface that meets the security requirements
of content providers and system operators. For further
information on HDMI, visit the HDMI website at
“http://www.hdmi.org/”.
■ DSD
Direct Stream Digital (DSD) technology stores audio
signals on digital storage media, such as Super Audio
CDs. Using DSD, signals are stored as single bit values at
a high-frequency sampling rate of 2.8224 MHz, while
noise shaping and oversampling are used to reduce
distortion, a common occurrence with very high
quantization of audio signals. Due to the high sampling
rate, better audio quality can be achieved than that offered
by the PCM format used for normal audio CDs.
■ DTS 96/24
DTS 96/24 offers an unprecedented level of audio quality
for multi-channel sound on DVD video, and is fully
backward-compatible with all DTS decoders. “96” refers
to a 96 kHz sampling rate compared to the typical 48 kHz
sampling rate. “24” refers to 24-bit word length.
DTS 96/24 offers sound quality transparent to the original
96/24 master, and 96/24 5.1-channel sound with fullquality full-motion video for music programs and motion
picture soundtracks on DVD video.
■ DTS (Digital Theater Systems)
Digital Surround
DTS digital surround was developed to replace the analog
soundtracks of movies with a 6.1-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. Digital Theater Systems Inc.
has developed a home theater system so that you can enjoy
the depth of sound and natural spatial representation of
DTS digital surround in your home. This system produces
practically distortion-free 6.1-channel sound (technically,
front left and right, center, surround left and right, and
LFE 0.1 (subwoofer) channels for a total of 5.1 channels).
This unit incorporates a DTS-ES decoder that enables 6.1channel reproduction by adding the surround back channel
to the existing 5.1-channel format.
132 En
■ LFE 0.1 channel
This channel reproduces low-frequency signals. The
frequency range of this channel is from 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low-frequency range compared to the full-range
reproduced by the other 5/6 channels in Dolby Digital or
DTS 5.1/6.1-channel systems.
■ Neo:6
Neo:6 decodes the conventional 2-channel sources for 6channel playback by the specific decoder. It enables
playback with the full-range channels with higher
separation just like digital discrete signal playback. There
are two modes available: “Music mode” for music sources
and “Cinema mode” for movie sources.
■ Neural Surround
Neural Surround™ represents the latest advancement in
surround technology and has been adopted by XM
Satellite Radio for digital radio broadcast of surround
recordings and live events in surround sound. Neural
Surround™ employs psychoacoustic frequency domain
processing which allows delivery of a more detailed sound
stage with superior channel separation and localization of
audio elements. System playback is scalable from 5.1 to
7.1 multi-channel surround playback.
■ PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for “Pulse Code
Modulation”, the analog signal is encoded as pulses and
then modulated for recording.
01EN_00_RX-V1700_U.book Page 133 Tuesday, June 27, 2006 9:37 AM
GLOSSARY
■ Sampling frequency and number of
quantized bits
When digitizing an analog audio signal, the number of
times the signal is sampled per second is called the
sampling frequency, while the degree of fineness when
converting the sound level into a numeric value is called
the number of quantized bits. The range of rates that can
be played back is determined based on the sampling rate,
while the dynamic range representing the sound level
difference is determined by the number of quantized bits.
In principle, the higher the sampling frequency, the wider
the range of frequencies that can be played back, and the
higher the number of quantized bits, the more finely the
sound level can be reproduced.
■ S-video signal
With the S-video signal system, the video signal normally
transmitted using a pin cable is separated and transmitted
as the Y signal for the luminance and the C signal for the
chrominance through the S-video cable. Using the
S VIDEO jack eliminates video signal transmission loss
and allows recording and playback of even more beautiful
images.
ADDITIONAL
INFORMATION
133 En
01EN_00_RX-V1700_U.book Page 134 Tuesday, June 27, 2006 9:37 AM
SOUND FIELD PROGRAM INFORMATION
SOUND FIELD PROGRAM INFORMATION
■ Elements of a sound field
■ SILENT CINEMA
What really creates the rich, full tones of a live instrument
are the multiple reflections from the walls of the room. In
addition to making the sound live, these reflections enable
us to tell where the player is situated as well as the size
and shape of the room in which we are sitting.
There are two distinct types of sound reflections that
combine to make up the sound field in addition to the
direct sound coming straight to our ears from the player’s
instrument.
YAMAHA has developed a natural, realistic sound effect
DSP algorithm for headphones. Parameters for
headphones have been set for each sound field so that
accurate representations of all the sound field programs
can be enjoyed on headphones.
Early reflections
Reflected sounds reach our ears extremely rapidly (50 ms
to 100 ms after the direct sound), after reflecting from one
surface only (for example, from a wall or the ceiling).
Early reflections actually add clarity to the direct sound.
Reverberations
These are caused by reflections from more than one
surface (for example, from the walls, and the ceiling) so
numerous that they merge together to form a continuous
sonic afterglow. They are non-directional and lessen the
clarity of the direct sound.
Direct sound, early reflections and subsequent
reverberations taken together help us to determine the
subjective size and shape of the room, and it is this
information that the digital sound field processor
reproduces in order to create sound fields.
If you could create the appropriate early reflections and
subsequent reverberations in your listening room, you
would be able to create your own listening environment.
The acoustics in your room could be changed to those of a
concert hall, a dance floor, or a room with virtually any
size at all. This ability to create sound fields at will is
exactly what YAMAHA has done with the digital sound
field processor.
■ CINEMA DSP
Since the Dolby Surround and DTS systems were
originally designed for use in movie theaters, their effect
is best felt in a theater having many speakers designed for
acoustic effects. Since home conditions, such as room
size, wall material, number of speakers, and so on, can
differ so widely, it is inevitable that there are differences in
the sound heard. Based on a wealth of actually measured
data, YAMAHA CINEMA DSP uses YAMAHA original
sound field technology to combine Dolby Pro Logic,
Dolby Digital and DTS systems to provide the audiovisual
experience of a movie theater in the listening room of your
own home.
134 En
■ Virtual CINEMA DSP
YAMAHA has developed a Virtual CINEMA DSP
algorithm that allows you to enjoy DSP sound field
surround effects even without any surround speakers by
using virtual surround speakers. It is even possible to
enjoy Virtual CINEMA DSP using a minimal two-speaker
system that does not include a center speaker.
■ Sound output from each speaker
Sound output from each speaker depends on the type of
audio signals being input. Refer to the diagrams in the
table below to understand the speaker layout for each
sound field program. For details about the sound output
from each speaker in sound field programs, refer to
“SOUND OUTPUT IN EACH SOUND FIELD
PROGRAM” in “APPENDIX” at the end of this manual.
Note
Be advised that there may be no or not enough sound output from
speakers depending on the type of input source being played
back. Furthermore, there may be some channels that can only be
used partially when they are adjusted to specific aspects of
movies, such as special sound effects, etc.
y
Except for “2ch Stereo”, “7ch Stereo”, and “STRAIGHT”, you
can select a decoder to output sound from the surround back
speakers (see page 45).
01EN_00_RX-V1700_U.book Page 135 Tuesday, June 27, 2006 9:37 AM
PARAMETRIC EQUALIZER INFORMATION
PARAMETRIC EQUALIZER INFORMATION
This unit employs YAMAHA Parametric Room Acoustic
Optimizer (YPAO) technology, together with the
Parametric EQ settings (see page 91), to optimize the
frequency characteristics of its parametric equalizer to
match your listening environment. YPAO uses a
combination of the following three parameters
(Frequency, Gain and Q factor) to provide highly precise
adjustment of the frequency characteristics.
■ Q factor
The width of the specified frequency band is referred to as
the Q factor. This parameter is adjustable between the
values 0.5 and 10.
■ Frequency
This parameter is adjustable in one-third octave
increments between 32 Hz and 16 kHz.
■ Gain
This parameter is adjustable in increments of 0.5 dB
between –20 and +6 dB.
YPAO adjusts frequency characteristics to suit your
listening requirements using a combination of the above
three parameters (Frequency, Gain and Q factor) for each
equalizer band in this unit’s parametric equalizer. This unit
has 7 equalizer bands for each channel.
The use of multiple equalizer bands enables more precise
adjustments of frequency characteristics (as in Figure 2).
This is not possible using only a single equalizer band (as
in Figure 1).
Figure 1
Gain
Frequency
characteristic after
correction
Band 1
Original frequency
characteristic
Figure 2
Gain
Frequency
characteristic after
correction
Band 1
Frequency
Band 2
Original frequency
characteristic
135 En
ADDITIONAL
INFORMATION
Frequency
01EN_00_RX-V1700_U.book Page 136 Tuesday, June 27, 2006 9:37 AM
SPECIFICATIONS
SPECIFICATIONS
AUDIO SECTION
• Minimum RMS Output Power for Front, Center, Surround,
Surround back
20 Hz to 20 kHz, 0.04% THD, 8 Ω .................................... 130 W
• Dynamic Power (IHF)
8/6/4/2 Ω ....................................................... 160/195/255/335 W
• Maximum Useful Output Power (JEITA)
[Asia, General, China and Korea models]
1 kHz, 10% THD, 8 Ω ....................................................... 175 W
• Maximum Output Power [U.K. and Europe models]
1 kHz, 0.7% THD, 4 Ω ...................................................... 180 W
• Dynamic Headroom
8 Ω ....................................................................................... 0.9 dB
• IEC Output Power [U.K. and Europe models]
1 kHz, 0.04% THD, 8 Ω .................................................... 130 W
• Damping Factor (IHF)
20 Hz to 20 kHz, 8 Ω ................................................. 150 or more
• Input Sensitivity/Input Impedance
PHONO .................................................................. 3.5 mV/47 kΩ
CD, etc. ................................................................. 200 mV/47 kΩ
MULTI CH INPUT ............................................... 200 mV/47 kΩ
• Maximum Input Voltage
PHONO (1 kHz, 0.1% THD) ................................ 60 mV or more
CD, etc. (1 kHz, 0.5% THD) ................................... 2.4 V or more
• Rated Output Voltage/Output Impedance
OUT (REC) ........................................................... 200 mV/900 Ω
PRE OUT ................................................................. 1.0 V/1.2 kΩ
SUBWOOFER ......................................................... 2.0 V/1.2 kΩ
ZONE 2/ZONE 3 OUT ............................................ 1.0 V/1.4 kΩ
• Tone Control (Front L/R)
BASS Boost/Cut ....................................................... ±6 dB/50 Hz
BASS Turnover Frequency ................................................. 350 Hz
TREBLE Boost/Cut ................................................ ±6 dB/20 kHz
TREBLE Turnover Frequency ........................................... 3.5 kHz
• Zone 2/Zone 3 Tone Control (Front L/R)
BASS Boost/Cut ................................................... ±10 dB/100 Hz
BASS Turnover Frequency ................................................. 450 Hz
TREBLE Boost/Cut .............................................. ±10 dB/10 kHz
TREBLE Turnover Frequency ........................................... 2.0 kHz
• Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz)
H.P.F. (Front, Center, Surround, Surround back) .......... 12 dB/oct.
L.P.F. (Subwoofer) ......................................................... 24 dB/oct.
VIDEO SECTION
• Video Format (Gray Back)
[U.S.A., Canada, General and Korea models] ..................... NTSC
[U.K., Europe, Australia, Asia and China models] ................ PAL
• Video Format (Video Conversion) ................................. NTSC/PAL
• Signal Level
Composite ................................................................. 1 Vp-p/75 Ω
S-video ............................ 1 Vp-p/75 Ω (Y), 0.286 Vp-p/75 Ω (C)
Component ................... 1 Vp-p/75 Ω (Y), 0.7 Vp-p/75 Ω (PB/PR)
• Maximum Input Level (Video Conversion Off)
............................................................................... 1.5 Vp-p or more
• Signal to Noise Ratio (Video Conversion Off)
.................................................................................... 60 dB or more
• Frequency Response (MONITOR OUT)
Component (Video Conversion Off)
............................................................. 5 Hz to 100 MHz, ±3 dB
• Headphone Jack Rated Output/Impedance
CD, etc. (1 kHz, 40 mV, 8 Ω) ................................ 150 mV/100 Ω
FM SECTION
• Frequency Response
CD to Front L/R, Pure Direct ........... 10 Hz to 100 kHz, +0/–3 dB
• Tuning Range
[U.S.A. and Canada models] .......................... 87.5 to 107.9 MHz
[Asia and General models] ....... 87.5/87.50 to 108.0/108.00 MHz
[Other models] ............................................ 87.50 to 108.00 MHz
• RIAA Equalization Deviation
PHONO (20 Hz to 20 kHz) .......................................... 0 ± 0.5 dB
• Total Harmonic Distortion
PHONO to OUT (REC)
(20 Hz to 20 kHz, 1 V) .......................................... 0.02% or less
CD, etc. to Front L/R
(20 Hz to 20 kHz, 65 W, 8 Ω) ............................... 0.04% or less
• Signal to Noise Ratio (IHF-A Network)
PHONO (5 mV) to Front L/R
[Australia, U.K. and Europe models] ..................... 81 dB or more
[Other models] ....................................................... 86 dB or more
CD, etc. (250 mV) to Front L/R ........................... 100 dB or more
• Residual Noise (IHF-A Network)
Front L/R ................................................................ 150 µV or less
• Channel Separation (1 kHz/10 kHz)
PHONO (shortened) to Front L/R ............... 60 dB/55 dB or more
CD, etc.
(5.1 kΩ shortened) to Front L/R .............. 60 dB/45 dB or more
• 50 dB Quieting Sensitivity (IHF)
Mono/Stereo ........................................ 2.0/25 µV (17.3/39.2 dBf)
• Usable Sensitivity (IHF) ...................................... 1.0 µV (11.2 dBf)
• Selectivity (400 kHz) .............................................................. 70 dB
• Signal to Noise Ratio (IHF)
Mono/Stereo ............................................................. 76 dB/70 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo ................................................................... 0.2/0.3%
• Stereo Separation (1 kHz)
Stereo .................................................................................... 42 dB
• Frequency Response
Stereo ............................................. 20 Hz to 15 kHz, +0.5, –2 dB
• Antenna Input (unbalanced) ..................................................... 75 Ω
AM SECTION
• Tuning Range
[U.S.A. and Canada models] .............................. 530 to 1710 kHz
[Asia and General models] ................. 530/531 to 1710/1611 kHz
[Other models] .................................................... 531 to 1611 kHz
• Usable Sensitivity ............................................................. 300 µV/m
136 En
01EN_00_RX-V1700_U.book Page 137 Tuesday, June 27, 2006 9:37 AM
SPECIFICATIONS
GENERAL
• Power Supply
[U.S.A. and Canada models] ............................. AC 120 V, 60 Hz
[General and Asia model]
....................................... AC 110/120/220/230–240 V, 50/60 Hz
[China model] .................................................... AC 220 V, 50 Hz
[Korea model] .................................................... AC 220 V, 60 Hz
[Australia model] ............................................... AC 240 V, 50 Hz
[U.K. and Europe models] ................................. AC 230 V, 50 Hz
• Power Consumption
[U.S.A. and Canada models] ................................. 500 W/630 VA
[Other models] .................................................................... 500 W
• Standby Power Consumption
[U.S.A. and Canada models] .................................... 0.1 W or less
[General model] (AC 240 V, 50 Hz) ....................... 0.33 W or less
[Other models] .......................................................... 0.1 W or less
• Maximum Power Consumption [General model only]
6ch, 10% THD .................................................................. 1100 W
• AC Outlets
[U.S.A. and Canada models] .... 2 (Total 100 W/0.8 A maximum)
[Asia, General and China models] ........ 2 (Total 50 W maximum)
[Australia and U.K. models] ..... 1 (Total 100 W/0.4 A maximum)
[Europe model] ......................... 2 (Total 100 W/0.4 A maximum)
• Dimensions (W x H x D) ............................. 435 x 171 x 438.5 mm
(17.1 x 6.7 x 17.3 in)
• Weight .................................................................. 17.0 kg (38.8 lbs)
* Specifications are subject to change without notice.
We Want You Listening For A Lifetime
ADDITIONAL
INFORMATION
YAMAHA and the Electronic Industries
Association’s Consumer Electronics Group want
you to get the most out of your equipment by
playing it at a safe level. One that lets the sound
come through loud and clear without annoying
blaring or distortion – and, most importantly,
without affecting your sensitive hearing. Since hearing damage
from loud sounds is often undetectable until it is too late,
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid prolonged exposure
from excessive volume levels.
137 En
01EN_00_RX-V1700_U.book Page i Tuesday, June 27, 2006 9:37 AM
SOUND OUTPUT IN EACH SOUND FIELD PROGRAM
L
Front left speaker
SL
Surround left speaker
SBR
Surround back right speaker
C
Center speaker
SR
Surround right speaker
PL
Presence left speaker
R
Front right speaker
SBL
Surround back left speaker
PR
Presence right speaker
Speaker from which no sound is being output
Speaker from which sound is being output
*1
EX
/
PL x
/
: OFF
*2
EX
/
PL x
/
: ON, PRIORITY: PRNS
*3
EX
/
PL x
/
: ON, PRIORITY: SB
Input source
Program
CLASSICAL
Hall in Munich
Hall in Vienna
Hall in
Amsterdam
Church in
Freiburg
Chamber
LIVE/CLUB
Village
Vanguard
Warehouse Loft
Cellar Club
The Roxy
Theatre
The Bottom Line
ENTERTAINMENT
Sports
Action Game
Roleplaying
Game
Music Video
Recital/Opera
MOVIE
STANDARD
2-channel audio
(monaural)
PL
L
SL
PR
C
SBL SBR
PL
L
SL
SBL SBR
PL
(PRO LOGIC)
L
SL
L
SR
SL
SBL SBR
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
PL
R
PR
C
2-channel audio
(stereo)
SBL SBR
PL
R
L
SR
SL
L
SR
SL
SBL SBR
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
PL
R
PR
C
5.1/6.1-channel
audio *1
SBL SBR
PL
R
L
SR
SL
L
SR
SL
SBL SBR
L
SR
SL
APPENDIX-i
SBL SBR
SBL SBR
L
SR
SL
SBL SBR
PL
L
SR
SL
L
SR
SL
SBL SBR
L
SR
SL
R
SR
PR
C
SBL SBR
PL
R
(Dolby Digital)
/
(DTS)
PR
C
PL
R
PR
C
5.1/6.1-channel
audio *3
R
PR
C
PL
R
(Dolby Digital)
/
(DTS)
PR
C
PL
R
PR
C
PL
R
PR
C
5.1/6.1-channel
audio *2
R
SR
PR
C
SBL SBR
R
SR
(Dolby Digital)
/
(DTS)
01EN_00_RX-V1700_U.book Page ii Tuesday, June 27, 2006 9:37 AM
Input source
Program
MOVIE
STANDARD
(PLII Movie)
(PLIIx Movie)
(Neo:6 Cinema)
2-channel audio
(monaural)
PL
L
SL
PR
C
SBL SBR
2-channel audio
(stereo)
PL
R
L
SR
SL
PR
C
SBL SBR
L
SL
PL
R
L
SR
SL
PRIORITY: PRNS
PL
5.1/6.1-channel
audio *1
PR
C
SBL SBR
5.1/6.1-channel
audio *2
PL
R
L
SR
SL
PR
C
SBL SBR
5.1/6.1-channel
audio *3
PL
R
L
SR
SL
PR
C
SBL SBR
R
SR
(Dolby Digital)
/
(DTS)
(Dolby Digital)
/
(DTS)
(Dolby Digital)
/
(DTS)
PL
PL
PL
PR
C
SBL SBR
R
SR
PRIORITY: SB
MOVIE
Spectacle
Sci-Fi
Adventure
Drama
Mono Movie
PL
L
SL
STEREO
2ch Stereo
PR
C
SBL SBR
PL
L
SL
L
SR
SL
PR
C
SBL SBR
PL
R
PR
C
SBL SBR
PL
R
L
SR
SL
R
L
SR
SL
PR
C
SBL SBR
PR
C
SBL SBR
PL
R
L
SR
SL
R
L
SR
SL
PR
C
SBL SBR
PR
C
SBL SBR
PL
R
L
SR
SL
R
L
SR
SL
PR
C
SBL SBR
PR
C
SBL SBR
PL
R
L
SR
SL
R
SR
PR
C
SBL SBR
R
SR
Monaural playback
STEREO
7ch Stereo
PL
L
SL
PR
C
SBL SBR
PL
L
SL
L
SR
SL
PR
C
PL
R
PR
C
SBL SBR
PL
R
L
SR
SL
L
SR
SL
PR
C
PL
R
PR
C
SBL SBR
PL
R
L
SR
SL
L
SR
SL
PR
C
PL
R
PR
C
SBL SBR
PL
R
L
SR
SL
L
SR
SL
PR
C
PL
R
PR
C
SBL SBR
PL
R
L
SR
SL
R
SR
PR
C
R
SR
APPENDIX-ii
01EN_00_RX-V1700_U.book Page iii Tuesday, June 27, 2006 9:37 AM
Input source
Program
SURROUND DECODE
PRO LOGIC
2-channel audio
(monaural)
PL
L
SL
PR
C
SBL SBR
2-channel audio
(stereo)
PL
R
L
SR
SL
PR
C
SBL SBR
L
SL
PL
R
L
SR
SL
PRO LOGIC
PL
5.1/6.1-channel
audio *1
PR
C
SBL SBR
5.1/6.1-channel
audio *2
PL
R
L
SR
SL
Dolby Digital
/
DTS
PR
C
SBL SBR
5.1/6.1-channel
audio *3
PL
R
L
SR
SL
Dolby Digital
/
DTS
PR
C
SBL SBR
R
SR
Dolby Digital
/
DTS
PR
C
SBL SBR
R
SR
Dolby Digital
/
DTS
SURROUND DECODE
PLII Movie
PLII Music
PLII Game
PL
L
SL
PR
C
SBL SBR
L
SR
SL
Movie/Game
PL
L
SL
PL
R
PR
C
SBL SBR
PL
R
L
SR
SL
Movie/Music/Game
PR
C
SBL SBR
PL
R
L
SR
SL
Dolby Digital
/
DTS
PR
C
SBL SBR
PL
R
L
SR
SL
Dolby Digital
/
DTS
PR
C
SBL SBR
R
SR
Dolby Digital
/
DTS
PR
C
SBL SBR
R
SR
Music
SURROUND DECODE
PLIIx Movie
PLIIx Music
PLIIx Game
PL
L
SL
PR
C
SBL SBR
L
SR
SL
Movie/Game
PL
L
SL
SBL SBR
Music
APPENDIX-iii
PR
C
SBL SBR
R
SR
PL
R
L
SR
SL
Movie/Music/Game
PR
C
PL
R
PR
C
SBL SBR
PL
R
L
SR
SL
Dolby Digital
/
DTS
PR
C
SBL SBR
PL
R
L
SR
SL
Dolby Digital
/
DTS
PR
C
SBL SBR
R
SR
Dolby Digital
/
DTS
01EN_00_RX-V1700_U.book Page iv Tuesday, June 27, 2006 9:37 AM
Input source
Program
SURROUND DECODE
Neo:6 Cinema
Neo:6 Music
2-channel audio
(monaural)
PL
L
SL
PR
C
SBL SBR
L
SL
PL
R
L
SR
SL
Cinema
PL
2-channel audio
(stereo)
PR
C
SBL SBR
5.1/6.1-channel
audio *1
PL
R
L
SR
SL
Cinema/Music
PR
C
SBL SBR
5.1/6.1-channel
audio *2
PL
R
L
SR
SL
Dolby Digital
/
DTS
PR
C
SBL SBR
5.1/6.1-channel
audio *3
PL
R
L
SR
SL
Dolby Digital
/
DTS
PR
C
SBL SBR
R
SR
Dolby Digital
/
DTS
PR
C
SBL SBR
R
SR
Music
SURROUND DECODE
neural sur.
PL
L
SL
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
SBL SBR
PL
R
L
SR
SL
Dolby Digital
/
DTS
PR
C
SBL SBR
PL
R
L
SR
SL
Dolby Digital
/
DTS
PR
C
SBL SBR
R
SR
Dolby Digital
/
DTS
STRAIGHT
PL
L
SL
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
SBL SBR
R
SR
Monaural playback
PURE DIRECT
PL
L
SL
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
SBL SBR
PL
R
L
SR
SL
PR
C
SBL SBR
R
SR
Monaural playback
APPENDIX-iv
01EN_00_RX-V1700_U.book Page v Tuesday, June 27, 2006 9:37 AM
LIST OF REMOTE CONTROL CODES
CABLE
ABC
0030, 0035
AMERICAST 0926
BELL SOUTH 0926
BIRMINGHAM CABLE
COMMUNICATIONS
0303
BRITISH TELECOM 0030
CABLE & WIRELESS
1095
DAERYUNG 0035, 0504, 0904,
1904
DIRECTOR
0503
FILMNET
0470
GENERAL INSTRUMENT
0030, 0303, 0503,
0837,
GOLDSTAR 0171
HAMLIN
0036, 0300
JERROLD
0030, 0303, 0503,
0837
LG
0171
MNET
0470
MEMOREX
0027
MOTOROLA 0303, 0503, 0837,
1133
NTL
1095
NOOS
0844
ONO
1095
PVP STEREO VISUAL MATRIX
0030
PACE
0264, 1087, 1095
PANASONIC 0027, 0035, 0134
PARAGON
0027
PHILIPS
0332, 0344
PIONEER
0171, 0560, 0904,
1904
PULSAR
0027
QUASAR
0027
REGAL
0300, 0306
RUNCO
0027
SAGEM
0844
SAMSUNG
0027, 0171
SCIENTIFIC ATLANTA
0035, 0504, 0904,
1904
SONY
1033
STARCOM
0030
SUPERCABLE
0303
TS
0030
TELE+1
0470
TELEWEST
1095
TORX
0030
TOSHIBA
0027
TRANS PX
0303
UNITED CABLE
0030
ZENITH
0027, 0552, 0926
CD PLAYER
AIWA
0184
ARCAM
0184
AUDIO RESEARCH 0184
AUDIO TON 0184
AUDIOLAB
0184
AUDIOMECA 0184
CAIRN
0184
APPENDIX-v
CALIFORNIA AUDIO LABS
0056
CARVER
0184, 0206
CYRUS
0184
DKK
0027
DMX ELECTRONICS
0184
DENON
0900
DYNAMIC BASS
0206
EMERSON
0332
FISHER
0206
GENEXXA
0059, 0332
GOODMANS 0332
GRUNDIG
0184
HARMAN/KARDON
0184, 0200
HITACHI
0059
JVC
0099
KENWOOD
0055, 0064
KRELL
0184
LXI
0332
LINN
0184
MCS
0056
MAGNAVOX 0184, 0332
MARANTZ
0056, 0184
MATSUI
0184
MEMOREX
0332
MERIDIAN
0184
MICROMEGA 0184
MIRO
0027
MISSION
0184
MYRYAD
0184
NAD
0027
NSM
0184
NAIM
0184
OPTIMUS
0027, 0059, 0064,
0206, 0332
PANASONIC 0056
PHILIPS
0184
PIONEER
0059, 0332
POLK AUDIO 0184
PROTON
0184
QED
0184
QUAD
0184
QUASAR
0056
RCA
0059, 0206, 0332
REALISTIC
0206
REVOX
0184
ROTEL
0184
SAE
0184
SANSUI
0184, 0332
SANYO
0206
SCOTT
0332
SEARS
0332
SHARP
0064
SIMAUDIO
0184
SONIC FRONTIERS 0184
SONY
0027
SYMPHONIC 0332
TAG MCLAREN
0184
TANDY
0059
TECHNICS
0056
THORENS
0184
THULE
0184
UNIVERSUM 0184
VICTOR
0099
WARDS
0184
YAMAHA
2300, 2301
CD RECORDER
KENWOOD
MARANTZ
PHILIPS
YAMAHA
0653
0653
0653
2400
DVD PLAYER
ACOUSTIC SOLUTIONS
0757
ALBA
0744
AMSTRAD
0740
APEX DIGITAL
0699, 0744,
0782, 0821, 0823,
0857, 1127
BLAUPINKT 0744
BLUE PARADE
0598
BUSH
0740
CENTREX
0699
CLATRONIC 0815
CYBERHOME 0741
DVD2000
0548
DAEWOO
0811, 0797
DANSAI
0797
DECCA
0797
DENON
0517
DIAMOND
0795
DIGITREX
0699
EMERSON
0618
ENTERPRISE 0618
FISHER
0697
GE
0549, 0744
GO VIDEO
0742
GOLDSTAR 0768
GRADIENTE 0678
GREENHILL 0744
GRUNDIG
0566
HITACHI
0600, 0691
HITEKER
0699
JVC
0585, 0650
KLH
0744
KENWOOD
0517, 0561
KOSS
0678
LG
0768
LIMIT
0795
MAGNAVOX 0530, 0702
MARANTZ
0566
MEMOREX
0858
MICO
0750
MICROSOFT 0549
MINTEK
0744
MITSUBISHI 0548
MUSTEK
0757
NESA
0744
ONKYO
0530
ORITRON
0678
PALSONIC
0699
PANASONIC 0517, 0659, 1389
PHILIPS
0530, 0566, 0673,
0881
PIONEER
0552, 0598, 0658,
0659
POLK AUDIO 0566
PROSCAN
0549
QWESTAR
0678
RCA
0549, 0598, 0744
ROTEL
0650
SM ELECTRONIC 0757
SAMSUNG
0600
SANYO
0697
SHARP
0657
SHERWOOD 0797
SHINSONIC 0560
SLIM ART
0811
SONY
0560, 0891
SYLVANIA
0702
TATUNG
0797
TEAC
0598, 0744
TECHNICS
0517
THETA DIGITAL
0598
THOMSON
0549
TOSHIBA
0530
URBAN CONCEPTS 0530
XBOX
0549
YAMAHA
0517, 0566, 0572,
2100
ZENITH
0530, 0618, 0768
ZEUS
0811
DVD RECORDER
HITACHI
PANASONIC
PHILIPS
PIONEER
SHARP
SONY
TOSHIBA
VICTOR
YAMAHA
2815
2800, 2801, 2802
2808
2804, 2805, 2806
2812, 2813
2809, 2810, 2811
2803
2814
2807
LD PLAYER
CARVER
DENON
MARANTZ
MITSUBISHI
NAD
NAGSMI
OPTIMUS
PHILIPS
PIONEER
SALORA
SONY
TELEFUNKEN
YAMAHA
0091
0086
0091
0086
0086
0086
0086
0091
0086
0091
0228
0086
2200
MD RECORDER
KENWOOD
ONKYO
SHARP
SONY
YAMAHA
0708
0895
0888
0517
2500, 2501, 2502
RECEIVER (TUNER)
ADC
AIWA
0558
0185, 1116, 1415,
1432, 1668
ALCO
1417
ANAM
1636
APEX DIGITAL
1284
AUDIOLAB
1216
AUDIOTRONIC
1216
AUDIOVOX 1417
BOSE
1256
01EN_00_RX-V1700_U.book Page vi Tuesday, June 27, 2006 9:37 AM
CAMBRIDGE SOUNDWORKS
1397
CAPETRONIC 0558
CARVER
1116, 1216
CENTREX
1284
DENON
1387
FERGUSON 0558
FINE ARTS
1216
GRUNDIG
1216
HARMAN/KARDON
0137, 1331
INTEGRA
0162, 1325
JBL
0137, 1333
JVC
0101, 0558, 1401,
1522
KLH
1417, 1439
KENWOOD
1054, 1340
MCS
0066
MAGNAVOX 0558, 1116, 1216,
1296,
MARANTZ
0066, 1116, 1216,
1316
MICROMEGA 1216
MUSICMAGIC
1116
MYRYAD
1216
NAD
0347
NORCENT
1416
ONKYO
0162, 0869, 1325
OPTIMUS
0558, 1050
PANASONIC 0066, 1315, 1545,
1790
PHILIPS
1116, 1216, 1293,
1295, 1296, 1310,
1316
PIONEER
0041, 0558, 1050,
1411
POLK AUDIO 1316
PROSCAN
1281
QUASAR
0066
RCA
0558, 1050, 1281,
1417, 1636,
SABA
0558
SANSUI
1116
SCHNEIDER 0558
SONY
0185, 1085, 1185,
1685, 1785
STEREOPHONICS 1050
SUNFIRE
1340
TEAC
1417
TECHNICS
0066, 1335, 1336,
1545
TELEFUNKEN
0558
THOMSON
1281
THORENS
1216
UHER
0558
VENTURER
1417
VICTOR
0101
WARDS
0041, 0185
YAMAHA
0203, 1203, 1358,
2601
(TUNER ID1)
2602
(TUNER ID2)
2603
(XM ID1)
2604
(XM ID2)
2605
(iPod)
2606
SATELLITE TUNER
@SAT
ABSAT
ALBA
ALPHASTAR
AMSTRAD
ASTON
ASTRO
1327
0150
0482
0799
0874
0169, 1156
0200
ATSAT
1327
AVALON
0423
BLAUPUNKT 0200
BRITISH SKY BROADCASTING
0874, 1202
CANAL DIGITAL
0880
CANAL SATELLITE 0880
CANAL+
0880
CHAPARRAL 0243
CITYCOM
1203
CONNEXIONS
0423
CROSSDIGITAL
1136
CYRUS
0227
D-BOX
0750, 1154
DMT
1102
DNT
0227, 0423
DAERYUNG 0423
DAEWOO
1323
DIGENIUS
0326
DIRECTV
0274, 0419, 0593,
0666, 0751, 0776,
0846, 1103, 1136,
1169, 1776, 1883
DISH NETWORK SYSTEM
0802, 1032
DISHPRO
0802, 1032
DISTRATEL 0111
DREAM MULTIMEDIA
1264
ECHOSTAR 0194, 0423, 0637,
0802, 0880, 0898,
1032, 1113
ENGEL
1044
EXPRESSVU 0802
FTE
0890
FINLUX
0482
FRACARRO 0898
FUBA
0423
GE
0593
GOI
0802
GALAXIS
0890, 1138
GENERAL INSTRUMENT
0896
GOLD BOX
0880
GRUNDIG
0200, 0874
HTS
0802
HIRSCHMANN
0200, 0423
HITACHI
0482, 0846
HUGHES NETWORK SYSTEM
0776, 1169, 1776
HUMAX
0890, 1203
INVIDEO
0898
JVC
0802
KATHREIN
0150, 0200, 0227,
0276, 0685, 1248
KREISELMEYER
0200
LABGEAR
1323
LOGIX
1044
LORENZEN 0326
MAGNAVOX 0749, 0751
MANHATTAN
0482, 1044,
1110
MARANTZ
0227
MEDIASAT
0880
MEMOREX
0751
METRONIC
0111
MITSUBISHI 0776
MOTOROLA 0896
MYRYAD
0227
NEXT LEVEL 0896
NOKIA
0482, 0750, 0778,
1154, 1250, 1750
OCTALTV
1032
ORBITECH
PACE
1127
0482, 0874, 1202,
1350
PANASONIC 0274, 0728, 0874,
1347
PANDA
0482
PAYSAT
0751
PHILIPS
0160, 0227, 0482,
0749, 0751, 0776,
0880, 1103, 1169,
1776
PIONEER
0880
PROMAX
0482
PROSCAN
0419, 0593
RCA
0170, 0419, 0593,
0882
RFT
0227
RADIOSHACK
0896
RADIOLA
0227
RADIX
0423
SKY
0874, 0883, 1202
SM ELECTRONIC 1227
SABRE
0482
SAGEM
0847, 1141, 1280
SAMSUNG
1044, 1136, 1303,
1319
SAT CONTROL
1327
SATSTATION 1110
SCHWAIGER 1138
SEEMANN
0423
SIEMENS
0200
SONY
0666, 0874, 1666
STAR CHOICE
0896
STRONG
1327
TPS
0847, 1280
TANTEC
0482
TECHNISAT 1126, 1127
TELESTAR
1127
THOMSON
0482, 0880, 1073,
1318
TOPFIELD
1233
TOSHIBA
0776, 0817, 1776
ULTIMATETV
0419, 0666
UNIDEN
0749, 0751
UNIVERSUM 0200
VENTANA
0227
WISI
0200, 0423, 0482
XSAT
0150
ZEHNDER
1102
ZENITH
0883, 1883
TAPE DECK
AIWA
0056
CARVER
0056
GRUNDIG
0056
HARMAN/KARDON
0056
MAGNAVOX 0056
MARANTZ
0056
MYRYAD
0056
OPTIMUS
0054
PHILIPS
0056
PIONEER
0054
POLK AUDIO 0056
RCA
0054
REVOX
0056
SANSUI
0056
SONY
0270
THORENS
0056
WARDS
0054
YAMAHA
2700,2701
TV
AGB
AOC
0543
0036, 0057, 0087,
0119, 0120, 0135,
0205, 0207, 0478
ASA
0131
AWA
0036
ACURA
0036
ADDISON
0119, 0135, 0680
ADMIRAL
0120, 0190, 0490
ADVENT
0788
AIKO
0119
AKAI
0036, 0057, 0235,
0388, 0543, 0729,
0839
AKURA
0291
ALBA
0036, 0064, 0398,
0695
AMERICA ACTION 0207
AMPRO
0778
AMSTRAD
0036, 0064, 0198,
0398, 0439, 0460,
0543
ANAM
0036, 0207, 0277
ANAM NATIONAL 0277, 0677
ANITECH
0036
APEX DIGITAL
0775, 0792,
0794
AUDIOSONIC 0064, 0136
BANG & OLUFSEN 0592
BASIC
0036
BAUR
0064, 0388, 0539
BAYSONIC
0207
BEAUMARK 0205
BEKO
0397, 0513, 0741,
0742
BELL & HOWELL 0181
BEON
0064
BLAUPUNKT 0222
BLUE SKY
0695, 1064
BONDSTEC 0274
BRADFORD 0207
BRANDT
0136, 0362
BROKSONIC 0263, 0490
BUSH
0036, 0064, 0398,
0401, 0695, 1064
CCE
0064
CGE
0274
CTC
0274
CXC
0207
CANDLE
0057
CARNIVALE 0057
CARVER
0081, 0197
CASCADE
0036
CATHAY
0064
CELEBRITY 0027
CELERA
0792
CENTURION 0064
CHANGHONG
0792
CHING TAI
0036, 0119
CHUN YUN
0027, 0036, 0119,
0207
CHUNG HSIN 0080, 0135, 0207
CIMLINE
0036
CINERAL
0119, 0478
CITIZEN
0057, 0087, 0119
CLARION
0207
CLARIVOX
0064
CLATRONIC 0274, 0397
CONDOR
0347, 0397
CONRAC
0835
APPENDIX-vi
01EN_00_RX-V1700_U.book Page vii Tuesday, June 27, 2006 9:37 AM
CONTEC
CRAIG
CROSLEY
CROWN
0036, 0207
0207
0081
0036, 0064, 0207,
0397, 0445
CURTIS MATHES 0057, 0074,
0081, 0087, 0120,
0172, 0181, 0193,
0478, 0729, 1174,
1374
DAEWOO
0036, 0057, 0064,
0119, 0135, 0181,
0197, 0205, 0207,
0401, 0478, 0650,
0661, 1688
DANSAI
0064
DAYTON
0036
DE GRAAF
0235, 0575
DECCA
0064, 0543
DENON
0172
DIGATRON
0064
DIXI
0036, 0064
DUMONT
0044
DWIN
0747, 0801
ECE
0064
ELBE
0286
ELECTROBAND
0027
ELIN
0064, 0575
ELITE
0347
ELTA
0036
EMERSON
0181, 0205, 0207,
0263, 0388, 0490,
0650
ENVISION
0057,0840
EPSON
0860
ERRES
0064
ETHER
0036, 0057
ETRON
0036
EUROPHON 0543
FERGUSON 0064, 0100, 0136,
0265, 0314, 0362,
0587
FIDELITY
0388
FINLANDIA 0235, 0373
FINLUX
0064, 0131, 0132,
0373, 0543
FIRSTAR
0036, 0263
FIRSTLINE
0036, 0274, 0695
FISHER
0131, 0181, 0235,
0397
FLINT
0482
FORMENTI
0064, 0347
FORTRESS
0120
FRONTECH 0190, 0274, 0291
FUJITSU
0710, 0836
FUNAI
0207, 0198, 0291
FUTURETECH
0207
GE
0057, 0074, 0078,
0119, 0205, 0207,
0478, 0587, 1174,
1374, 1481
GEC
0064, 0543
GATEWAY
1782, 1783
GELOSO
0036
GENEXXA
0190
GIBRALTER 0044, 0057
GOLDSTAR 0057, 0064, 0136,
0181, 0205, 0404
GOODMANS 0064, 0398, 0401,
0661
GOREMJE
0397
GRADIENTE 0080, 0197
GRAETZ
0190, 0388
APPENDIX-vii
GRANADA
0064, 0235, 0366,
0543
GRANDIN
0637
GRUNDIG
0064, 0222, 0514,
0583, 0614
GRUNPY
0207
HCM
0036, 0439
HALLMARK 0205
HANKOOK
0057, 0205, 0207
HANSEATIC 0064, 0347, 0388,
0455, 0583
HANTAREX 0543
HARMAN/KARDON 0081
HARVARD
0207
HAVERMY
0120
HELLO KITTY
0478
HINARI
0036, 0064
HISAWA
0482
HITACHI
0036, 0057, 0119,
0132, 0136, 0172,
0190, 0205, 0252,
0383, 0508, 0575,
0605, 1172, 1283
HUA TUN
0036
HUANYU
0401
HYPSON
0064, 0291
ICE
0291, 0398
ITS
0398
ITT
0190, 0388, 0575
IMPERIAL
0274, 0397, 0445
INDIANA
0064
INFINITY
0081
INGELEN
0190
INNO HIT
0543
INNOVA
0064
INTEQ
0044
INTERFUNK 0064, 0190, 0274,
0388, 0539
INTERVISION
0064, 0291,
0404
JBL
0081
JCB
0027
JVC
0080, 0398, 0490,
0680, 0710
JEAN
0036, 0078, 0119,
0183, 0263
JENSEN
0788
KEC
0207
KTV
0057, 0207
KAISUI
0036
KAPSCH
0190
KARCHER
0637
KATHREIN
0583
KENDO
0064
KENWOOD
0057
KNEISSEL
0286, 0462
KOLIN
0080, 0135, 0207
KORPEL
0064
KOYODA
0036
L&S ELECTRONIC 0835
LG
0057, 0064, 0087,
0135, 0205, 0741
LXI
0074, 0081, 0181,
0183, 0205
LEYCO
0064, 0291
LIESENK & TTER 0064
LOEWE
0539
LUXOR
0383, 0388
M ELECTRONIC
0036, 0064,
0131, 0132, 0136,
0190, 0314, 0373,
0401, 0507
MGA
0057, 0177, 0205
MTC
0057, 0087, 0539
MAGNADYNE
0274, 0543
MAGNAFON 0543
MAGNAVOX 0057, 0081, 1281,
1481
MANESTH
0291, 0347
MARANTZ
0057, 0064, 0081,
0583
MARK
0064
MATSUI
0036, 0064, 0235,
0398, 0514, 0543
MATSUSHITA
0277, 0677
MEDIATOR 0064
MEDION
0695, 0835, 1064
MEGATRON 0172, 0205
MEMOREX
0036, 0177, 0181,
0205, 0277, 0490,
1064
METZ
0474
MICROMAXX
0835
MICROSTAR 0835
MIDLAND
0044, 0074, 0078
MINERVA
0514
MINOKA
0439
MITSUBISHI 0057, 0120, 0135,
0177, 0181, 0205,
0207, 0263, 0277,
0539, 0863, 1277
MIVAR
0318,0319, 0543,
0636
MOTOROLA 0120
MULTITECH 0036, 0207
MYRYAD
0583
NAD
0183, 0205, 0388,
0893
NEC
0036, 0057, 0078,
0181, 0183, 0197,
0205, 0482, 0524,
1731
NEI
0064
NTC
0119
NECKERMANN
0064, 0583
NETSAT
0064
NEWAVE
0036, 0119, 0120,
0205
NIKKAI
0064, 0291
NIKKO
0057, 0119, 0205
NOKIA
0388, 0500, 0507,
0575, 0658
NORCENT
0775, 0851
NORDMENDE
0136, 0314,
0587
OCEANIC
0190, 0388
ONWA
0207, 0460
OPTIMUS
0181, 0193, 0277,
0677
OPTONICA
0120
ORION
0064, 0263, 0347,
0490, 0543
OSAKI
0291, 0439
OTTO VERSAND
0064, 0347,
0539, 0583
PALLADIUM 0397, 0445
PANAMA
0291
PANASONIC 0064, 0078, 0081,
0190, 0277, 0677,
1437
PATHE CINEMA
0265, 0347
PAUSA
0036
PENNEY
0057, 0074, 0078,
0087, 0183, 0205,
1374
PERDIO
0347
PHILCO
0057, 0064, 0081,
0172, 0205, 0207,
0274, 0490, 1688
PHILIPS
0027, 0057, 0064,
0078, 0081, 0119,
0135, 0205, 0401,
0583, 0717, 1481
PHONOLA
0064
PILOT
0057
PIONEER
0136, 0190, 0193,
0314, 0706, 0787,
0893
PORTLAND 0119
PRANDONI-PRINCE
0543
PRIMA
0788
PRISM
0078
PROFEX
0036, 0388
PROSCAN
0074
PROTECH
0036, 0064, 0274,
0291, 0445, 0695
PROTON
0036, 0057, 0205
PULSAR
0044
QUASAR
0078, 0277, 0677
QUELLE
0064, 0131, 0388,
0539
R-LINE
0064
RCA
0027, 0057, 0074,
0117, 0119, 0205,
0706, 1074, 1174,
1274, 1374, 1474,
1481, 1574
RFT
0455
RADIOSHACK
0057, 0074,
0181, 0205, 0207
RADIOLA
0064
RADIOMARELLI
0543
REALISTIC
0057, 0181, 0205,
0207
REDIFFUSION
0388
REOC
0741
REVOX
0064
REX
0190, 0286, 0291
ROADSTAR 0036, 0291, 0445
RUNCO
0044, 0057, 0524,
0630
SBR
0064
SEG
0291, 0695
SEI
0543
SKY
0064
SSS
0207
SABA
0136, 0190, 0314,
0362
SACCS
0265
SAGEM
0637
SAISHO
0036, 0291, 0543
SALORA
0190, 0380, 0388,
0575
SAMBERS
0543
SAMPO
0036, 0057, 0119,
0120, 0181, 0198,
0205, 0677, 1782
SAMSUNG
0036, 0057, 0064,
0087, 0117, 0119,
0181, 0205, 0291,
0397, 0583, 0614,
0645, 0729, 0793,
0839, 0841
SANSEI
0478
SANSUI
0490
SANYO
0131, 0181, 0207,
0235, 0366, 0826
SCHAUB LORENZ 0388
SCHNEIDER 0064, 0274, 0398,
0695
SCOTCH
0205
SCOTT
0205, 0207, 0263
01EN_00_RX-V1700_U.book Page viii Tuesday, June 27, 2006 9:37 AM
SEARS
0074, 0081, 0181,
0183, 0198, 0205
SELECO
0190, 0286
SEMIVOX
0207
SEMP
0183
SHARP
0057, 0120, 0677
SHEN YING 0036, 0119
SHENG CHIA 0036, 0120, 0263
SIAREM
0543
SIEMENS
0064, 0222
SINUDYNE
0543
SKANTIC
0383
SKYGIANT
0207
SKYWORTH 0064
SOLAVOX
0190
SONITRON
0235
SONOKO
0036, 0064
SONOLOR
0190, 0235
SONTEC
0064
SONY
0027, 0677, 0861,
1127, 1532, 1678
SOUNDESIGN
0205, 0207
SOUNDWAVE
0064, 0445
SOWA
0078, 0087, 0119,
0183, 0205
SQUAREVIEW
0198
STANDARD 0036
STARLITE
0207
STERN
0190, 0286
SUPREME
0027
SYLVANIA
0057, 0081, 0198
SYMPHONIC 0198, 0207
SYNCO
0027, 0087, 0119,
0120, 0205, 0478
SYSLINE
0064
T+A
0474
TCM
0835
TMK
0205
TNCI
0044
TVS
0490
TACICO
0036, 0119, 0205
TAI YI
0036
TANDY
0120, 0190
TASHIKO
0119, 0677
TATUNG
0036, 0064, 0078,
0081, 0087, 0181,
0183, 0543
TEAC
0036, 0064, 0291,
0439, 0445, 0482,
0695, 1064
TEC
0274
TECHNEMA 0347
TECHNICS
0078, 0277, 0677
TECHWOOD 0078
TECO
0036, 0078, 0119,
0120, 0205, 0291,
0680
TEKNIKA
0081, 0087, 0119,
0177, 0207
TELEFUNKEN
0136, 0289,
0362, 0652, 0729
TELEMEISTER
0347
TELETECH
0036
TENSAI
0347
TERA
0057
THOMSON
0136, 0314, 0587,
0652, 1474
THORN
0064, 0131, 0388,
0539
TOSHIBA
0087, 0181, 0183,
0535, 0645, 0677,
0859, 1283, 1383,
1683, 1731
TRIUMPH
0543
TUNTEX
0036, 0057, 0119
UHER
0347
UNIVERSUM 0064, 0131, 0132,
0291, 0373, 0397,
0519
VECTOR RESEARCH
0057
VESTEL
0064
VICTOR
0080, 0277, 0677,
0680
VIDEOSAT
0274
VIDIKRON
0081
VIDTECH
0205
VIEWSONIC 1782
VISION
0347
VOXSON
0190
WALTHAM
0383
WARDS
0057, 0081, 0205,
0893
WATSON
0064, 0347
WAYCON
0183
WHITE WESTINGHOUSE
0064, 0347, 0490,
0650
YAMAHA
0057, 0172, 0677,
0796, 0860,
2900 (projector),
2901 (projector),
2903,
2904 (projector)
YAPSHE
0277
YOKO
0064, 0291
ZENITH
0044, 0119, 0205,
0490
VCR
ASA
ADMIRAL
ADVENTURA
AIKO
AIWA
0064, 0108
0075
0027
0305
0027, 0064, 0334,
0375, 0379
AKAI
0068, 0342
AKIBA
0099
ALBA
0099, 0305, 0342,
0379
AMERICA ACTION 0305
AMERICAN HIGH 0062
AMSTRAD
0027
ANAM
0064, 0253, 0267,
0305, 0507
ANAM NATIONAL 0253, 1589
ANITECH
0099
ASHA
0267
ASUKA
0064
AUDIOVOX 0064, 0305
BAIRD
0027, 0068, 0131
BASIC LINE 0099, 0305
BEAUMARK 0267
BELL & HOWELL 0131
BLAUPUNKT 0253
BRANDT
0347
BRANDT ELECTRONIC
0068
BROKSONIC 0211, 0375, 1506
BUSH
0099, 0305, 0379
CCE
0099, 0305
CGE
0027
CALIX
0064
CANON
0062
CARVER
0108
CIMLINE
0099
CINERAL
0305
CITIZEN
0064, 0305, 1305
COLT
0099
COMBITECH 0379
CRAIG
0064, 0074, 0099,
0267
CROWN
0099, 0305
CURTIS MATHES 0062, 0068,
0087, 1062
CYBERNEX 0267
CYRUS
0108
DAEWOO
0072, 0131, 0305,
0669, 1305
DANSAI
0099
DE GRAAF
0069
DECCA
0027, 0108
DENON
0069
DUAL
0068
DUMONT
0027, 0108, 0131
DYNATECH 0027
ESC
0267, 0305
ELCATECH
0099
ELECTROHOME
0064
ELECTROPHONIC 0064
EMEREX
0059
EMERSON
0027, 0062, 0064,
0070, 0072, 0211,
0267, 0305, 1305,
1506
FERGUSON 0068, 0347
FIDELITY
0027
FINLANDIA 0108, 0131
FINLUX
0027, 0069, 0108,
0131
FIRSTLINE
0064, 0070, 0072,
0099
FISHER
0074, 0131
FUJI
0060, 0062
FUJITSU
0027, 0072
FUNAI
0027
GE
0062, 0087, 0267,
0834, 1062, 1087
GEC
0108
GARRARD
0027
GENERAL
0072
GO VIDEO
0459
GOLDHAND 0099
GOLDSTAR 0064, 0252, 0507,
1264
GOODMANS 0027, 0064, 0099,
0305
GRADIENTE 0027
GRAETZ
0068, 0131, 0267
GRANADA
0108, 0131
GRANDIN
0027, 0064, 0099
GRUNDIG
0099, 0108, 0253,
0374
HCM
0099
HI-Q
0074
HANSEATIC 0064
HARLEY DAVIDSON
0027
HARMAN/KARDON 0108
HARWOOD
0099
HINARI
0099, 0267, 0379
HITACHI
0027, 0064, 0068,
0069, 0267
HUGHES NETWORK SYSTEMS
0069
HYPSON
0099
ITT
0068, 0131, 0267
ITV
0064, 0305
IMPERIAL
0027
INTERFUNK 0108
JVC
0068, 0072, 0094
JENSEN
0068
KEC
0064, 0305
KLH
0099
KAISUI
KENWOOD
KODAK
KOLIN
KORPEL
LG
0099
0068, 0094
0062, 0064
0068, 0070
0099
0064, 0069, 0072,
0507
LXI
0064
LENCO
0305
LEYCO
0099
LLOYD’S
0027
LOEWE
0064, 0108, 1589
LOGIK
0099, 0267
LUXOR
0070, 0075, 0131
M ELECTRONIC
0027
MEI
0062
MGA
0070, 0267
MGN TECHNOLOGY
0267
MTC
0027, 0267
MAGNASONIC
1305
MAGNAVOX 0027, 0062, 0066,
0108, 1808
MAGNIN
0267
MANESTH
0072, 0099
MARANTZ
0062, 0108
MARTA
0064
MATSUI
0375, 0379
MATSUSHITA
0062
MEDION
0375
MEMOREX
0027, 0062, 0064,
0066, 0074, 0075,
0131, 0267, 0334,
0375, 1264
MEMPHIS
0099
METZ
0064, 0374, 1589
MINOLTA
0069
MITSUBISHI 0068, 0070, 0094,
0108, 0834
MOTOROLA 0062, 0075
MULTITECH 0027, 0099
MURPHY
0027
MYRYAD
0108
NAD
0131
NEC
0062, 0064, 0068,
0075, 0094, 0131
NATIONAL
0253
NECKERMANN
0108
NESCO
0099
NEWAVE
0064
NIKKO
0064
NOBLEX
0267
NOKIA
0068, 0131, 0267
NORDMENDE
0068, 0347
OCEANIC
0027, 0068
OKANO
0342, 0375
OLYMPUS
0062, 0253
OPTIMUS
0064, 0075, 0131,
0459
ORION
0211, 0375, 0379,
1506
OSAKI
0027, 0064, 0099
OTTO VERSAND
0108
PALLADIUM 0064, 0068, 0099
PANASONIC 0062, 0252, 0253,
0643, 1062, 1589
PATHE MARCONI 0068
PENNEY
0062, 0064, 0069,
0267, 1062, 1264
PENTAX
0069
PERDIO
0027
PHILCO
0062
PHILIPS
0062, 0108, 0645,
1108, 1208
PHONOLA
0108
APPENDIX-viii
01EN_00_RX-V1700_U.book Page ix Tuesday, June 27, 2006 9:37 AM
PILOT
0064
PIONEER
0069, 0094, 0108
POLK AUDIO 0108
PROFITRONIC
0267
PROLINE
0027
PROSCAN
0087, 1087
PROTEC
0099
PULSAR
0066
PYE
0108
QUASAR
0062, 1062
QUELLE
0108
RCA
0062, 0069, 0087,
0267, 0834, 1062,
1087
RADIOSHACK
0027
RADIOLA
0108
RADIX
0064
RANDEX
0064
REALISTIC
0027, 0062, 0064,
0074, 0075, 0131
REOC
0375
REPLAYTV
0641, 0643
REX
0068
ROADSTAR 0064, 0099, 0267,
0305
RUNCO
0066
SBR
0108
SEG
0267
SEI
0108
STS
0069
SABA
0068, 0347
SALORA
0070
SAMPO
0064, 0075
SAMSUNG
0072, 0267, 0459
SANKY
0066, 0075
SANSUI
0027, 0068, 0094,
1506
SANYO
0074, 0131, 0267
SAVILLE
0379
SCHAUB LORENZ 0027, 0068,
0131
SCHNEIDER 0027, 0099, 0108
SCOTT
0070, 0072, 0211
SEARS
0027, 0062, 0064,
0069, 0074, 0131,
1264
SELECO
0068
SEMP
0072
SHARP
0075, 0834
SHINTOM
0099, 0131
SIEMENS
0064, 0108, 0131
SILVA
0064
SINGER
0072, 0099
SINUDYNE
0108
SONIC BLUE 0641, 0643
SONTEC
0064
SONY
0027, 0059, 0060,
0062, 0663, 1259
SUNKAI
0375
SUNSTAR
0027
SUNTRONIC 0027
SYLVANIA
0027, 0062, 0108,
0070, 1808
SYMPHONIC 0027
TMK
0267
TANDY
0027, 0131
TASHIKO
0027, 0064
TATUNG
0027, 0068, 0072,
0094, 0108
TEAC
0027, 0068, 0305,
0334, 0669
TECHNICS
0062, 0253
TECO
0062, 0064, 0068,
0075
TEKNIKA
0027, 0062, 0064
APPENDIX-ix
TELEAVIA
TELEFUNKEN
TENOSAL
TENSAI
THOMAS
THOMSON
0068
0068, 0347
0099
0027
0027
0068, 0087, 0094,
0347
THORN
0068, 0131
TIVO
0645, 0663
TOSHIBA
0068, 0070, 0072,
0094, 0108, 0872
TOTEVISION 0064, 0267
UHER
0267
UNITECH
0267
UNIVERSUM 0027, 0064, 0108,
0267
VECTOR
0072
VICTOR
0068, 0094
VIDEO CONCEPTS 0072
VIDEOMAGIC
0064
VIDEOSONIC 0267
VILLAIN
0027
WARDS
0027, 0062, 0069,
0074, 0075, 0087,
0099, 0108, 0267
WHITE WESTINGHOUSE
0099
XR-1000
0027, 0062, 0099
YAMAHA
0068
YAMISHI
0099
YOKAN
0099
YOKO
0267
ZENITH
0027, 0060, 0066,
1506
01EN_00_RX-V1700_U.book Page x Tuesday, June 27, 2006 9:37 AM
RX-V1700_U-cv.fm Page 1 Monday, May 8, 2006 3:54 PM
U
RX-V1700
RX-V1700
AV Receiver
© 2006
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WH63550
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement