Yamaha RX-V565 Owners Manual

Add to my manuals
76 Pages

advertisement

Yamaha RX-V565 Owners Manual | Manualzz
U
RX-V565
AV Receiver
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
1
2
3
4
5
6
7
8
9
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
10
11
12
13
14
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modifications
not expressly approved by Yamaha may void your authority,
granted by the FCC, to use the product.
2 IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3 NOTE: This product has been tested and found to comply with
the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices. Compliance with these requirements provides a
reasonable level of assurance that your use of this product in a
residential environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the users
manual, may cause interference harmful to the operation of other
electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product is
found to be the source of interference, which can be determined by
turning the unit “OFF” and “ON”, please try to eliminate the
problem by using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please
contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
Caution-i En
Caution: Read this before operating your unit.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury. Yamaha
will not be held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
Caution-ii En
17 Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
18 Before moving this unit, press ASTANDBY/ON to set this
unit in the standby mode, and disconnect the AC power plug
from the wall outlet.
19 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC wall outlet. Voltages are:
.......AC 110/120/220/230–240 V, 50/60 Hz (General model)
.......................... AC 220/230–240 V, 50/60 Hz (Asia model)
20 The batteries shall not be exposed to excessive heat such as
sunshine, fire or like.
21 Excessive sound pressure from earphones and headphones can
cause hearing loss.
22 When replacing the batteries, be sure to use batteries of the
same type. Danger of explosion may happen if batteries are
incorrectly replaced.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
As long as this unit is connected to the AC wall outlet,
it is not disconnected from the AC power source even
if you turn off this unit by A STANDBY/ON. In this
state, this unit is designed to consume a very small
quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
POUR LES CONSOMMATEURS CANADIENS
Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante de
la prise et pousser jusqu’au fond.
Cet appareil numérique de la classe B est conforme à
la norme NMB-003 du Canada.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
Contents
INTRODUCTION
Front panel ................................................................. 4
Rear panel .................................................................. 5
Front panel display..................................................... 6
Remote control........................................................... 7
Quick start guide..................................................... 8
L
Preparing remote control ....................................... 9
Installing batteries in the remote control ................... 9
Using the remote control............................................ 9
Connections ...........................................................10
Using Auto Setup..................................................... 18
When an error message is displayed during
measurement........................................................ 20
When a warning message is displayed after
measurement........................................................ 20
BASIC OPERATION
Basic procedure........................................................ 21
Using the SCENE function ...................................... 21
Muting audio output temporarily (MUTE) .............. 22
Adjusting high/low frequency sound (tone control) 22
Enjoying pure hi-fi sound ........................................ 22
Using the sleep timer ............................................... 22
Using your headphones............................................ 22
Displaying input signal information ........................ 23
Changing information on the front panel display .... 23
Selecting a decoder used with a sound field program
............................................................................. 36
Setting sound field parameters................................. 36
Sound field parameters ............................................ 36
Operating various settings for this unit
(Setup menu) ..................................................... 38
Basic operation of the setup menu........................... 39
Speaker Setup .......................................................... 39
Sound Setup ............................................................. 41
Function Setup ......................................................... 42
DSP Parameter......................................................... 43
Memory Guard......................................................... 43
Controlling other components with the remote
control................................................................ 44
Setting remote control codes.................................... 44
Resetting all remote control codes........................... 44
Advanced setup..................................................... 45
APPENDIX
Troubleshooting.................................................... 46
General..................................................................... 46
HDMI....................................................................... 49
Tuner (FM/AM)....................................................... 49
Remote control......................................................... 50
iPod™ ...................................................................... 50
Bluetooth™.............................................................. 51
Auto Setup (YPAO)................................................. 51
Glossary ................................................................. 53
Sound field program information ....................... 55
Information on HDMI™...................................... 55
Specifications......................................................... 56
Index ...................................................................... 57
APPENDIX
Playback.................................................................21
OPTION menu items ............................................... 33
Editing surround decoders/sound field programs
............................................................................ 36
ADVANCED
OPERATION
Optimizing the speaker setting for your listening
room (YPAO) ....................................................18
Setting the option menu for each input source
(OPTION menu) ............................................... 33
BASIC
OPERATION
Placing speakers....................................................... 10
Connecting speakers ................................................ 11
Information on jacks and cable plugs ...................... 13
Connecting a TV monitor or projector .................... 14
Connecting other components ................................. 15
Connecting a Yamaha iPod universal dock or
Bluetooth™ wireless audio receiver.................... 16
Using the VIDEO AUX jacks on the front panel .... 16
Connecting the FM and AM antennas ..................... 17
Connecting the power cable..................................... 17
Turning this unit on and off ..................................... 17
ADVANCED OPERATION
PREPARATION
PREPARATION
Pairing the Bluetooth™ wireless audio receiver and
your Bluetooth component .................................. 32
Playback of the Bluetooth™ component ................. 32
INTRODUCTION
Features.................................................................... 2
About this manual................................................... 3
Supplied accessories................................................ 3
Part names and functions....................................... 4
Using Bluetooth™ components ........................... 32
(at the end of this manual)
List of remote control codes...................................i
Enjoy the sound field programs ..........................24
Selecting sound field programs................................ 24
Enjoying unprocessed input sources (Straight
decoding mode) ................................................... 27
Enjoying sound field programs without surround
speakers (Virtual CINEMA DSP) ....................... 27
Enjoy sound field programs with headphones
(SILENT CINEMA™) ........................................ 27
FM/AM tuning ...................................................... 28
Tuning in to the desired FM/AM station (Frequency
tuning).................................................................. 28
Registering FM/AM stations and tuning in (Preset
tuning).................................................................. 28
English
Using iPod™ ..........................................................30
Controlling iPod™................................................... 30
1 En
INTRODUCTION
Features
■ Built-in 7-channel power amplifier
• Minimum RMS Output Power (1 kHz, 0.9% THD, 8 Ω)
• FRONT L/R: 90 W + 90 W
• CENTER: 90 W
• SURROUND L/R: 90 W + 90 W
• SURROUND BACK L/R: 90 W + 90 W
■ Speaker/Preout outputs
• Speaker jacks (7-channel), preout output jacks
(subwoofer)
■
Input/Output terminals
Input terminals
• HDMI input x 4
• Audio/Visual input
[Audio] Digital input (coaxial) x 2, digital input
(optical) x 2, analog input x 2
[Video] Component video x 2, composite video x 4
• Audio input (analog) x 2
• Dock input x 1
• V-AUX input
[Audio] Analog x 1
[Video] Composite video x 1
Output terminals
• Monitor output
[Audio/Video] HDMI x 1
[Video] Component video x 1, Composite video x 1
• Audio/Visual output
[Audio] Analog x 1
[Video] Composite video x 1
• Audio output
Analog x 1
■
•
•
•
•
Proprietary Yamaha technology for the
creation of sound fields
CINEMA DSP
Compressed Music Enhancer mode
Virtual CINEMA DSP
SILENT CINEMA
■ Digital audio decoders
• Dolby TrueHD, Dolby Digital Plus decoder
• DTS-HD Master Audio, DTS-HD High Resolution
Audio, DTS Express
• Dolby Digital/Dolby Digital EX decoder
• DTS, DTS 96/24 decoder, DTS-ES Matrix 6.1,
DTS-ES Discrete 6.1
• Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic
IIx decoder
• DTS NEO:6 decoder
■ Sophisticated FM/AM tuner
• 40-station random and direct preset tuning
• Automatic preset tuning
2 En
■
HDMI™
(High-Definition Multimedia Interface)
• HDMI interface for standard, enhanced or highdefinition video as well as multi-channel digital audio.
– Automatic audio and video synchronization (lip sync)
information capability
– Deep Color video signal (30/36 bit) transmission
capability
– “x.v.Color” video signal transmission capability
– High refresh rate and high resolution video signals
capability
– High definition digital audio format signals capability
• Analog video to HDMI digital video up-conversion
(composite video → HDMI, component video →
HDMI) capability for monitor out
• Analog video input up-scaling for HDMI digital video
output 480i or 480p → 720p, 1080i or 1080p
■ DOCK terminal
• DOCK terminal to connect a Yamaha iPod universal
dock (such as YDS-11, sold separately) or Bluetooth
wireless audio receiver (such as YBA-10, sold
separately)
■ Automatic speaker setup features
• “YPAO” (Yamaha Parametric Room Acoustic
Optimizer) for automatically optimizing speaker
outputs suitable for listening environments.
■ Other features
• 192-kHz/24-bit D/A converter
• OSD (on-screen display) menus that allow you to
optimize this unit to suit your individual audiovisual
system
• Direct mode for pure hi-fi sound for all sources
• Adaptive dynamic range controlling capability
• Sleep timer
About this manual
Bluetooth™
Bluetooth is a registered trademark of Bluetooth SIG and is used by
Yamaha in accordance with a license agreement.
PREPARATION
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic and the double-D symbol are trademarks of Dolby
Laboratories
“HDMI,” the “HDMI” logo and “High-Definition Multimedia
Interface” are trademarks, or registered trademarks of HDMI
Licensing LLC.
iPod™
x.v.Color™
“x.v.Color” is a trademark of Sony Corporation. “SILENT CINEMA”
is a trademark of Yamaha Corporation.
“SILENT CINEMA” is a trademark of Yamaha Corporation.
“iPod” is a trademark of Apple Inc., registered in the U.S. and other
countries.
ADVANCED
OPERATION
Supplied accessories
BASIC
OPERATION
Manufactured under license under U.S. Patent No’s:
5,451,942;5,956,674;5,974,380;5,978,762;6,226,616;6,487,535 &
other U.S. and worldwide patents issued & pending. DTS is a
registered trademark and the DTS logos, Symbol, DTS-HD and DTSHD Master Audio are trademark of DTS, Inc. © 1996-2007 DTS, Inc.
All Rights Reserved.
INTRODUCTION
• y indicates a tip for your operation.
• Some operations can be performed by using either the keys on the front panel or the ones on the remote control. In case the key names differ between
the front panel and the remote control, the key name on the remote control is given in parentheses.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of
differences between the manual and product, the product has priority.
• “ASTANDBY/ON” or “gHDMI 1” (example) indicates the name of the parts on the front panel or the remote control. Refer to the attached sheet
or the pages at the end of this manual for the information about each position of the parts.
• ☞ indicates the page describing the related information.
ADDITIONAL
INFORMATION
Check that you received all of the following parts.
• Remote control
• Batteries (2) (AAA, R03, UM-4)
• Optimizer microphone
• AM loop antenna
• Indoor FM antenna
APPENDIX
English
3 En
Part names and functions
Front panel
U
T
D
E
F
G
H
P
VOLUME
HDMI THROUGH
INFO
l
MEMORY
PRESET
h
l
AM
FM
TUNING
h
SCENE
BD/DVD
PHONES
TONE CONTROL
PROGRAM
l
STANDBY
/ON
A
CD
STRAIGHT
DIRECT
C
INFO
B
C
J
K
LM
PRESET l / h
F
FM
G
AM
INPUT l / h
O
OPTIMIZER MIC jack
TUNING l / h
SCENE
Switches between linked sets of input sources and sound field
programs (see page 21).
J
TONE CONTROL
Adjusts high-frequency/low-frequency output of speakers (see
page 22).
K
PROGRAM l / h
L
STRAIGHT
Changes sound field programs (see page 24).
Changes a sound field program to straight decoding mode (see
page 27).
4 En
S
For connecting the supplied optimizer microphone and adjusting
output characteristics of speakers (see page 18).
P
VOLUME control
Q
VIDEO (VIDEO AUX) jack
Controls the volume of this unit (see page 21).
For connecting the video output cable of a camcorder or game
console (see page 16).
R
AUDIO L/R (VIDEO AUX) jack
For connecting the audio output cable of a camcorder or game
console (see page 16).
S
PORTABLE (VIDEO AUX) jack
For connecting the audio output cable of a portable music player
(see page 16).
Changes FM/AM tuner frequencies (see page 28).
I
R
PORTABLE
Selects an input source (see page 21).
Sets the FM/AM tuner band to AM (see page 28).
H
Q
AUDIO
Changes a sound field program to direct mode (see page 22).
Selects an FM/AM preset station (see page 29).
Sets the FM/AM tuner band to FM (see page 28).
I
N
Registers FM/AM stations as preset stations (see page 29).
E
O
DIRECT
Changes information display screens on the front panel display
(see page 23).
MEMORY
N
M
For plugging headphones (see page 22).
D
VIDEO AUX
OPTIMIZER MIC
h
VIDEO
Switches this unit between standby and on (see page 17).
PHONES jack
INPUT
EFFECT
STANDBY/ON
B
RADIO
l
h
SILENT CINEMA
A
TV
T
Front panel display
U
HDMI THROUGH
Displays information on this unit (see page 6).
Lights up during pass-through output of an HDMI signal input
to this unit while this unit is on standby (see page 42).
Part names and functions
Rear panel
c
b
d
k
INTRODUCTION
a
SPEAKERS
(BD/DVD)
DOCK
HDMI 2
HDMI 1
HDMI OUT
HDMI 3
ANTENNA
HDMI 4
FRONT
COMPONENT
VIDEO
COMPONENT
VIDEO
CENTER
UNBAL.
PR
SURROUND
SURROUND BACK/BI-AMP
PR
GND AM
PREPARATION
FM
PB
PB
VIDEO
VIDEO
Y
Y
MONITOR OUT
OPTICAL
COAXIAL
COAXIAL
AV 2
AV 3
( TV )
AV 1
OPTICAL
(CD)
AV 4
a
AV 6
AV
OUT
f
AUDIO1
AUDIO2
g
h
SUBWOOFER
AUDIO
OUT
PRE OUT
i
j
BASIC
OPERATION
e
AV 5
DOCK terminal
For connecting an optional Yamaha iPod universal dock (YDS11) or Bluetooth wireless audio receiver (YBA-10) (see
page 16).
b
HDMI OUT/HDMI 1-4
c
ANTENNA jack
d
SPEAKERS terminal
ADVANCED
OPERATION
For connecting an HDMI-compatible video monitor or external
components for HDMI inputs 1-4 (see page 15).
For connecting supplied FM and AM antennas (see page 17).
For connecting front right and left, center, surround and
surround back speakers (see page 11).
e
AV 1-6
ADDITIONAL
INFORMATION
For connecting external components for audio/visual inputs 1-6
(see page 15).
f
AV OUT
Outputs audio/visual signals from a selected analog input source
to an external component (see page 16).
g
AUDIO 1/2
For connecting external components for audio inputs 1-2 (see
page 16).
h
MONITOR OUT
Outputs visual signals from this unit to a video monitor, such as
a TV (see page 14).
APPENDIX
i
AUDIO OUT
Outputs audio signals from a selected analog input source to an
external component (see page 16).
j
PRE OUT
For connecting a subwoofer with a built-in amplifier (see
page 11).
k
Power Cable
For connecting this cable to an AC wall outlet (see page 17).
English
5 En
Part names and functions
Front panel display
a
b
c
d
SLEEP
STEREO
TUNED
f
e
VOL.
MUTE
SW
C
L
R
SL
SR
SBL SB SBR
g
a
h
HDMI indicator
Lights up during normal communication when HDMI is
selected as an input source.
b
CINEMA DSP indicator
Lights up when a sound field program that uses CINEMA DSP
is selected.
c
Tuner indicator
Lights up while receiving a radio broadcast signal from an FM/
AM station (see page 28).
d
SLEEP indicator
e
VOLUME indicator
f
MUTE indicator
g
Cursor indicators
Lights up when the sleep timer is activated (see page 22).
Displays volume levels.
Flashes when audio is muted.
Light up if corresponding cursors on the remote control are
available for operations.
h
Multi information display
i
Speaker indicators
Displays menu items and settings for the current operation.
Indicate speaker terminals from which signals are currently
output.
Subwoofer
Front L
Surround L
Surround back L
SW
C
L
R
SL
SR
SBL SB SBR
Center
Front R
Surround R
Surround back R
Surround back
6 En
g
i
Part names and functions
Remote control
g
b
HDMI 1-4
AV 1-6
AUDIO 1/2
V-AUX
CODE SET
TRANSMIT
c
d
POWER
SOURCE
POWER
SLEEP
e
HDMI
1
2
1
2
3
4
3
4
Input selection keys
f
[A]/[B]
AV
5
6
1
2
V-AUX
[ A ]
[ B ]
DOCK
DOCK
TUNER
TUNER
h
h
FM
AM
PRESET
i
MEMORY
MOVIE
MUSIC
FM
AM
MEMORY
PRESET k / n
TUNING k / n
ENHANCER SUR. DECODE
j
STEREO
STRAIGHT
DIRECT
i
SCENE
k
l
BD
DVD
TV
CD
SETUP
Tuner keys
Presets radio stations.
Selects a preset station.
Changes tuning frequencies.
INFO
Changes the information shown on the front panel display (see
page 23).
RADIO
m
OPTION
Switches a band between FM and AM.
j
Sound selection keys
k
SCENE
BASIC
OPERATION
INFO
TUNING
PREPARATION
g
AUDIO
Selects HDMI inputs 1 through 4.
Selects AV inputs 1 through 6.
Selects AUDIO inputs 1 and 2.
Selects the V-AUX jack on the front
panel of this unit.
To control external components using
the rExternal component
operation keys separately from
operations of this unit (see page 44).
Selects a Yamaha iPod universal dock/
Bluetooth wireless audio receiver
connected to the DOCK jack.
Selects the FM/AM tuner.
INTRODUCTION
a
Selects sound field programs (see page 24).
n
TOP
MENU
MENU
MUTE
q
p
l
SETUP
m
OPTION
n
Cursors k / n / l / h/ENTER/RETURN
Displays the setup menu (see page 39).
REC
ADVANCED
OPERATION
Switches between linked sets of input sources and sound field
programs (see page 21).
DISPLAY
RETURN
r
o
VOLUME
ENTER
Displays the option menu (see page 33).
2
3
4
5
6
7
8
9
0
10
Cursors k / n / l / h Select menu items displayed on the
ENT
ENTER
RETURN
TV
INPUT
t
POWER
TV VOL
TV CH
MUTE
o
VOLUME +/–
p
DISPLAY
front panel display or on a video
monitor, or change settings.
Confirms a selected item.
Returns to the previous screen or
ends the menu display.
ADDITIONAL
INFORMATION
s
1
Adjust the volume of this unit (see page 21).
Remote control signal transmitter
b
TRANSMIT
Transmits infrared signals.
Changes the operation mode of the iPod connected to the
Yamaha iPod universal dock (see page 30).
q
Turns the mute function of the sound output on and off (see
page 22).
Lights up when a signal is output from the remote control.
c
CODE SET
r
SOURCE POWER
s
Numeric keys
t
TV control keys
Enter numbers.
Switches an external component on and off.
e
SLEEP
f
Operate a monitor such as a TV or projector.
English
Switches the sleep timer operations (see page 22).
External component operation keys
Operate recording, playback etc. of external components (see
page 44).
Sets remote control codes for external component operations
(see page 44).
d
MUTE
APPENDIX
a
POWER
Switches this unit on and standby.
7 En
Quick start guide
When you use this product for the first time, perform setup following the steps below. See the related pages for details on
operations and settings.
Step 1: Prepare items for setup
Step 2: Set up your speakers
Prepare speakers, DVD player, cables, and other items
necessary for setup.
For example, prepare the following items for setting up a
5.1-channel sound system.
Front right speaker
Place your speakers in the room and connect them to this
unit.
• Placing speakers
• Connecting speakers
☞P. 10
☞P. 11
y
Video monitor
• This unit has a YPAO (Yamaha Parametric Room Acoustic Optimizer)
that automatically optimizes this unit based on room acoustic
characteristics (audio characteristics of the speakers, speaker positions,
and room acoustics, etc.).
You can enjoy good balanced sound without special knowledge by using
the YPAO technology (see page 18).
Subwoofer
Front left speaker
Step 3: Connect your components
Connect your TV, DVD player, or other components.
Center speaker
Components
(such as DVD player)
Surround right speaker
• Connecting a TV monitor or projector
• Connecting other components
• Connecting a Yamaha iPod universal dock or
Bluetooth wireless audio receiver
• Connecting the FM and AM antennas
☞P. 14
☞P. 15
☞P. 16
☞P. 17
Surround left speaker
Step 4: Turn on the power
Requirements
Speakers
qty.
Front speaker
2
Center speaker
1
Surround speaker
2
Active subwoofer
1
Speaker cable
5
Subwoofer cable
1
Reproduction component such as DVD player
1
Video monitor such as TV
1
Video cable or HDMI cable
2
Audio cable
2
y
• Prepare two speakers (for front). The priority of the requirement of other
speakers is as follows:
1 Two surround speakers
2 One center speaker
3 One (or two) surround back speaker(s)
• If your video monitor is a CRT, we recommend that you use magnetically
shielded speakers.
8 En
Connect the power cable and turn on this unit.
• Connecting the power cable
• Turning this unit on and off
☞P. 17
☞P. 17
Step 5: Select the input source and start
playback
Select the component connected in the step 3 as an input
source and start playback.
• Basic procedure
• Selecting sound field programs
☞P. 21
☞P. 24
y
• This unit supports the SCENE function that changes the input source and
sound field program at one time. Four scenes are preset for different
purposes for Blu-ray disc, DVD and CD, and you can select from a scene
from those just by pressing a remote control key. See page 21 for details.
PREPARATION
Preparing remote control
1
Using the remote control
The remote control transmits a directional infrared ray. Be
sure to aim the remote control directly at the remote
control sensor on this unit during operation.
3
Remote control sensor window
PREPARATION
2
30
2
Insert the two supplied batteries (AAA, R03,
UM-4) according to the polarity markings (+
and –) on the inside of the battery
compartment.
Snap the battery compartment cover back
into place.
Notes
Notes
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following conditions:
– places of high humidity, such as near a bath
– places of high temperatures, such as near a heater or stove
– places of extremely low temperatures
– dusty places
y
• You can operate external components with this remote control by setting
the remote control code. See page 44 for details.
ADDITIONAL
INFORMATION
APPENDIX
• Change all batteries if you notice the following conditions:
– the operation range of the remote control narrows
– the transmit indicator does not flash or is dim
• Do not use old batteries together with new ones.
This may shorten the life of the new batteries or cause old batteries
to leak.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Specification of batteries may be
different even though they look the same.
• If you find leaking batteries, discard the batteries immediately,
taking care not to touch the leaked material. If the leaked material
comes into contact with your skin or gets into your eyes or mouth,
rinse it away immediately and consult a doctor. Clean the battery
compartment thoroughly before installing new batteries.
• Dispose of the old batteries correctly in accordance with your local
regulations.
• If the remote control is without batteries for more than 2 minutes,
or if exhausted batteries remain in the remote control, the contents
of the memory may be cleared. In such a case, install new batteries
and set the remote control code.
within 6 m (20 ft)
ADVANCED
OPERATION
Take off the battery compartment cover.
30
BASIC
OPERATION
1
3
INTRODUCTION
Installing batteries in the remote
control
English
9 En
Connections
Placing speakers
This unit supports up to 7.1-channel surround. We recommended the following speaker layout in order to obtain the
optimum surround effect.
7.1-channel speaker layout
Speaker channels
C
FR
FL
SW
SW
30˚
SL
SR
60˚
80˚
SL
SR
SBL
SBR
30 cm (12 in) or more
6.1-channel speaker layout
C
FR
FL
SW
SW
30˚
■ Front left and right speakers (FL and FR)
The front speakers are used for the front channel sounds
(stereo sound) and effect sounds. Place these speakers at
an equal distance from the ideal listening position. When
using a screen, the appropriate top positions of the
speakers are about 1/4 of the screen from the bottom.
■ Center speaker (C)
The center speaker is for the center channel sounds
(dialog, vocals, etc.). Place it halfway between the left and
right speakers. When using a TV, place the speaker just
above or just under the center of the TV with the front
surfaces of the TV and the speaker aligned. When using a
screen, place it just under the center of the screen.
■ Surround left and right speakers (SL and SR)
The surround speakers are used for effect and surround
sounds.
Place them at the rear left and rear right facing the
listening position.
To obtain a natural sound flow in the 5.1-channel speaker
layout, place them slightly further back than in the 7.1channel speaker layout.
■
SL
SR
60˚
SL
80˚
SR
SB
5.1-channel speaker layout
C
FR
FL
SW
SW
30˚
SL
SR
60˚
SL
10 En
80˚
SR
Surround back left and right speakers (SBL
and SBR) / Surround back speaker (SB)
The surround back left and right speakers are used for rear
effect sounds. Place them at the rear of the room facing the
listening position at least 30 cm away from each other,
ideally at the same distance as that between the front left
and right speakers.
In the 6.1-channel speaker layout, surround back left and
right channel sound signals are mixed down and output
from the single surround back speaker.
In the 5.1-channel speaker layout, surround back left and
right channel sound signals are output from the surround
left and right speakers.
■ Subwoofer (SW)
The subwoofer speaker is used for bass sounds and lowfrequency effect (LFE) sounds included in Dolby Digital
and DTS signals. Use a subwoofer with a built-in
amplifier, such as the Yamaha Active Servo Processing
Subwoofer System. Place it exterior to the front left and
right speakers facing slightly inward to reduce reflections
from a wall.
Connections
Connecting speakers
When you connect speakers, connect them to the respective terminals as follows, according to your speaker layout.
7.1-channel
Speakers
b
a
g
c
f
Jacks on this unit
a Front speaker L
FRONT (L)
b Front speaker R
FRONT (R)
c Center speaker
CENTER
d Surround speaker L
SURROUND (L)
e Surround speaker R
SURROUND (R)
f Surround back speaker L
SURROUND
BACK/BI-AMP (L)
g Surround back speaker R
SURROUND
BACK/BI-AMP (R)
h Subwoofer
SUB WOOFER
INTRODUCTION
■
SPEAKERS
HDMI 4
FRONT
CENTER
SURROUND BACK/BI-AMP
SURROUND
6.1-channel
SUBWOOFER
AUDIO
OUT
Speakers
PRE OUT
d
h
FRONT (L)
b Front speaker R
FRONT (R)
c Center speaker
CENTER
d Surround speaker L
SURROUND (L)
e Surround speaker R
SURROUND (R)
f Surround back speaker
SURROUND
BACK/BI-AMP (L)
h Subwoofer
SUB WOOFER
■
5.1-channel
Speakers
Jacks on this unit
FRONT (L)
b Front speaker R
FRONT (R)
c Center speaker
CENTER
d Surround speaker L
SURROUND (L)
e Surround speaker R
SURROUND (R)
h Subwoofer
SUB WOOFER
APPENDIX
a Front speaker L
ADDITIONAL
INFORMATION
a Front speaker L
ADVANCED
OPERATION
e
Jacks on this unit
BASIC
OPERATION
■
PREPARATION
DMI 3
English
11 En
Connections
Connecting the speaker cable
Caution
• A speaker cable is a pair of insulated cables running side by side in general. One of the cables is colored differently
or striped to indicate a polarity. Connect one end of the colored/striped cable to the “+” (red) terminal of this unit
and the other end to that of your speaker, and connect one end of the other cable to the “–” (black) terminal of this
unit and the other end to that of your speaker.
• Before connecting the speakers, be sure to disconnect the power cable.
• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or
speakers. If the circuit shorts out, “CHECK SP WIRES!” appears on the front panel display when this unit is turned on.
• Use magnetically shielded speakers. If images on the monitor are still distorted even when you use the magnetically
shielded speakers, place the speakers away from the monitor.
• Use speakers with an impedance of 6-ohm or larger. Set speaker impedance in “ADVANCED SETUP” before
connecting the speakers (see page 45).
■
Connecting to the FRONT terminals
1
Remove approximately 10 mm (0.4 in) of
insulation from the end of each speaker
cable and then twist bare wires of the cable
together so that they will not cause a short
circuits.
■
Connecting to the CENTER, SURROUND,
SURROUND BACK/BI-AMP terminals
1
Press down the tab and insert the bare end of
the speaker cable into the hole in the
terminal.
Red: positive (+)
Black: negative (–)
10 mm (0.4 in)
2
Loosen the knob, insert the twisted bare
wires into the hole, and then tighten the
knob.
2
Red: positive (+)
1
Black: negative (–)
3
Connecting the banana plug (Except U.K.,
Europe, Asia and Korea models)
Tighten the knob, and then insert the banana plug into
the end of the terminal.
2
Release the tab to secure the wire.
Using bi-amplification connections
You can connect speakers that support bi-amplification
connections to this unit. Before connecting the speakers,
set this unit to enable bi-amplification connections in
“ADVANCED SETUP” (see page 45), and connect the
speakers to this unit as shown below.
Front speakers
Right
FRONT
Left
SURROUND BACK/BI-AMP
This unit
Banana plug
Caution
Before making bi-amplification connections, remove
any or cables that connect a woofer with a tweeter.
Refer to the instruction manuals of speakers for details.
When not making bi-amplification connections, make
sure that the brackets or cables are connected before
connecting the speaker cables.
12 En
Connections
Information on jacks and cable plugs
■
■
Audio jacks
Jack and cables
AUDIO jacks
(white)
L
Description
R
(red)
To transmit coaxial digital audio
signals. Use pin cables for digital
audio signals.
(orange)
C
O
To transmit optical digital audio
signals. Use optical fiber cables for
optical digital audio signals.
OPTICAL
Video jacks
Jack and cables
VIDEO jacks
VIDEO
V
HDMI
Description
• We recommend that you use a commercially available 19-pin HDMI
cable no longer than 5 meters (16 feet) with the HDMI logo printed on it.
• You can check the potential problem about the HDMI connection (see
page 23).
• You can check error information on HDMI connections (see page 23).
A video signal input to this unit is output from the
output terminals in MONITOR OUT for the same kind
of signal as the input signal.
For example, if a VCR with a composite output signal
and a DVD player with a COMPONENT VIDEO
output signal are connected, connect both VIDEO jack
and COMPONENT VIDEO jack in MONITOR OUT
to the video monitor.
If an HDMI input compatible monitor is connected, this
unit automatically converts an analog signal that is
input from a video input terminal to a digital video
signal, and then output it from the HDMI OUT jack.
To transmit conventional
composite video signals. Use video
pin cables.
Input
HDMI
COMPONENT VIDEO
COMPONENT VIDEO
jacks
COMPONENT
VIDEO
PR
To transmit component video
signals that include luminance (Y),
chrominance blue (PB) and
chrominance red (PR) components.
Use component video cables.
PR
PB
COMPONENT VIDEO
PR
Y
VIDEO
PB
Y
VIDEO
Repeat
Converted
ADDITIONAL
INFORMATION
(yellow)
PR
Output
HDMI
ADVANCED
OPERATION
■
HDMI
To transmit digital video and
digital audio signals. Use HDMI
cables.
BASIC
OPERATION
COAXIAL
OPTICAL jacks
HDMI jacks
Description
y
AUDIO
COAXIAL jacks
Jack and cables
PREPARATION
To transmit conventional analog
left and right audio signals. Use
stereo pin cables. Connect red
plugs to red jacks (R) and white
plugs to white jacks (L).
Video/audio jacks
INTRODUCTION
This unit has the following input and output jacks. Use jacks and cables appropriate for components that you are
connecting.
(red)
PB
PB
(blue)
Y
APPENDIX
Y
(green)
English
13 En
Connections
Connecting a TV monitor or projector
Connect a video monitor such as a TV or projector to an output terminal of this unit. You can select one of the following
three types according to the input signal format supported by the video monitor.
Note
• When you connect this unit to the video monitor, make sure that this unit is on standby.
Outputting sound of a TV from this unit
TV, or projector
c
a
To output sound of a TV from this unit, make connection
between the AV input 1-6 and an audio output terminal.
If the TV supports an optical digital output, we
recommend that you use the AV input 1. Connecting to the
AV input 1 allows you to switch an input source to the AV
input 1 with just a single key operation using the SCENE
function (see page 21).
b
Y
HDMI
PB
PR
V
TV, or projector
Digital output
(optical)
(BD/DVD)
HDMI 2
HDMI 1
HDMI OUT
HD
ANTENNA
COMPONENT
VIDEO
UNBAL.
PR
FM
GND AM
UNBAL.
PB
PR
P
VIDEO
Y
FM
PB
MONITOR OUT
GND AM
Y
■
To connect an HDMI video monitor
Jacks on components
Jacks on this unit
Y
O
OPTICAL
COAXIAL
COAXIAL
AV 2
AV 3
( TV )
AV 1
a HDMI input
■
HDMI OUT
To connect component video monitor
Note
• Only video signals input from this unit via the component input terminal
are output from the component output terminal.
Jacks on components
b Component video output
■
Jacks on this unit
MONITOR OUT
(COMPONENT VIDEO)
To connect composite video monitor
Note
• Only video signals input from this unit via the composite video input
terminal are output from the composite video output terminal.
Jacks on components
c Video input (composite)
14 En
Jacks on this unit
MONITOR OUT (VIDEO)
P
VIDEO
OPTICAL
(CD)
AV 4
AV 5
AV 6
AV
OUT
AUDIO1
Connections
Connecting other components
Note
• When you connect this unit to the external components, make sure that this unit is on standby.
Audio / video input (AV 1-6)
Audio / video output (AV OUT)
PREPARATION
HDMI input
(HDMI 1-4)
(BD/DVD)
DOCK
HDMI 2
HDMI 1
HDMI OUT
HDMI 3
ANTENNA
HDMI 4
FRONT
COMPONENT
VIDEO
COMPONENT
VIDEO
CE
UNBAL.
PR
PR
GND AM
FM
PB
PB
VIDEO
VIDEO
Y
INTRODUCTION
This unit has input and output terminals for respective input and output sources. You can reproduce sound and movies
from input sources selected with the front panel display or remote control.
Y
MONITO OUT
MONITOR
BASIC
OPERATION
Audio output
(AUDIO OUT)
OPTICAL
COAXIAL
COAXIAL
AV 2
AV 3
( TV )
AV 1
OPTICAL
(CD)
AV 4
AV 5
AV
OUT
AV 6
AUDIO1
AUDIO
OUT
AUDIO2
Audio input (AUDIO 1-2)
ADVANCED
OPERATION
■
Audio and video player / Set-top box
Output jacks on the connected external component
External
components
External component
with HDMI output
Audio
HDMI output
Optical digital output
Video
Component video
Audio
Coaxial digital output
Video
Component video output
Audio
Coaxial digital output
Video
Composite output
Audio
Optical digital output
Video
Composite output
Audio
Analog audio output
Video
Composite output
Audio
Analog audio output
Video
Composite output
HDMI 1 (BD/DVD)
HDMI 1
HDMI 2
HDMI 2
HDMI 3
HDMI 3
HDMI 4
HDMI 4
AV 1 (TV)
OPTICAL
COMPONENT VIDEO
AV 2
COAXIAL
COMPONENT VIDEO
AV 3 (CD)
COAXIAL
VIDEO
AV 4
OPTICAL
AV 5
AUDIO
AV 6
AUDIO
APPENDIX
External component
with composite video
output
Audio/Video
Output jacks
ADDITIONAL
INFORMATION
External component
with component video
output
Input sources/jacks of this unit
Signals
VIDEO
VIDEO
VIDEO
• Input sources in parentheses are recommended to connect to the respective jacks. If your Yamaha component has the Remote in/out terminal, you can
switch the input source to that component with a single key operation using the SCENE function (see page 21).
• You can change the name of the input source displayed on the front panel display or the OSD on the video monitor as necessary (see page 43).
15 En
English
y
Connections
■
Audio player
Output jacks on the connected external component
Input sources/jacks of this unit
External components
Output jacks
External component with optical digital
output
Optical digital output
External component with coaxial digital
output
Coaxial digital output
External component with analog audio
output
Analog audio output
AV 1 (TV)
OPTICAL
AV 4
OPTICAL
AV 2
COAXIAL
AV 3 (CD)
COAXIAL
AV 5
AUDIO
AV 6
AUDIO
AUDIO 1
AUDIO
AUDIO 2
AUDIO
y
• We recommend connecting the coaxial digital output terminal of a CD player to the AV3 jack.
About audio/video output terminals
Among the analog audio and analog video signals input to this unit via input terminals, the audio/video signals of the
selected input sources are output from the AV OUT jack and AUDIO OUT jack. An HDMI input signal,
COMPONENT VIDEO input signal or digital audio input signal cannot be output.
When using the AV OUT jack: connect an external component to the composite or analog audio terminal.
When using the AUDIO OUT jack: connect an external component to the analog audio terminal.
Connecting a Yamaha iPod universal
dock or Bluetooth™ wireless audio
receiver
This unit has the DOCK jack, to which you can connect a
Yamaha iPod universal dock (YDS-11, sold separately) or
a Bluetooth wireless audio receiver (YBA-10, sold
separately). You can play an iPod or a Bluetooth
component with this unit by connecting it to the DOCK
jack.
Use a dedicated cable for connection between the dock/
receiver and this unit.
Using the VIDEO AUX jacks on the
front panel
Use the VIDEO AUX jacks on the front panel to connect a
game console or a video camera to this unit. Be sure to
turn down the volume of this unit and other components
before making connections.
VOLUME
l
PRESET
h
l
AM
FM
TUNING
h
SCENE
BD/DVD
OGRAM
TV
CD
RADIO
STRAIGHT
DIRECT
INPUT
l
h
VIDEO AUX
OPTIMIZER MIC
h
EFFECT
VIDEO
DOCK
AUDIO
PORTABLE
HDMI OUT
ANTENNA
COMPONENT
VIDEO
UNBAL.
VIDEO
L
AUDIO
R
PORTABLE
PR
FM
PB
GND
VIDEO
Y
L
R
Analog audio
output
Analog audio
output
Video output
V
Yamaha iPod universal
dock/Bluetooth wireless
audio receiver
Game console/Camcorder
Music player
Note
• When external components are connected both the PORTABLE jack and
AUDIO jack, sound input from the PORTABLE jack is output.
16 En
Connections
Connecting the FM and AM antennas
After all connections are complete, plug the AC power
cable of this unit into an AC wall outlet.
To the AC wall outlet
Indoor FM antenna
AM loop
antenna
PREPARATION
Outdoor AM antenna
Connect a 5 to 10 m (16
to 33 ft) vinyl-covered
wire, and extend it
outdoors (use the AM
loop antenna together
with this antenna).
Power cable
(BD/DVD)
DOCK
HDMI 2
HDMI 1
HDMI OUT
HDMI 3
ANTENNA
F
COMPONENT
VIDEO
COMPONENT
VIDEO
UNBAL.
PR
PR
FM
PB
GND AM
PB
VIDEO
VIDEO
Y
INTRODUCTION
An indoor FM antenna and an AM loop antenna are
supplied with this unit. Connect these antennas properly to
the respective jacks.
Connecting the power cable
Y
MONITOR OUT
y
Assembling the AM loop antenna
1
Press ASTANDBY/ON on the front panel (or
fPOWER on the remote control) to turn on
this unit.
2
Press ASTANDBY/ON (or fPOWER) again
to turn off this unit (standby mode).
y
Caution
Do not unplug this unit while it is turned on. Doing so
may damage this unit or cause the settings of this unit
to be saved incorrectly.
Press and hold
Insert
APPENDIX
Connecting the AM loop antenna
The wires of the AM loop antenna have no polarity. You
can connect either wire to the AM terminal and the other
to the GND terminal.
ADDITIONAL
INFORMATION
• The unit needs a few seconds until ready to play back.
• You can also turn on this unit by pressing ISCENE (or kSCENE).
• This unit consumes a small amount of electricity even in the standby
mode. We recommend disconnecting the power cable from the AC wall
outlet.
ADVANCED
OPERATION
• The supplied antennas are normally sensitive enough to obtain good
reception.
• Position the AM loop antenna away from this unit.
• If you cannot get good reception, we recommend that you use an outdoor
antenna. For more details, consult the nearest authorized Yamaha dealer
or service center.
• Always use the AM loop antenna even when the outdoor antenna is
connected.
Turning this unit on and off
BASIC
OPERATION
Ground (GND terminal)
The GND terminal is not for earth
grounding.
To reduce noises, connect a ground bar or a
vinyl-covered wire with a copper plate at its
tip, and place it in the moist ground.
Release
English
17 En
Optimizing the speaker setting for your listening room (YPAO)
This unit has a Yamaha Parametric Acoustic Optimizer (YPAO). With the YPAO, this unit automatically adjusts the
output characteristics of your speakers based on speaker position, speaker performance, and the acoustic characteristics
of the room. We recommend that you first adjust the output characteristics with the YPAO when you use this unit.
1 AutoSetup
EQ Type;;;;Natural
. Start
[]/[]:Up/Down
[ENTER]:Start
[
y
“MIC ON. View OSD MENU” appears on the front panel
display.
The following menu screen appears on the video monitor.
[
Caution
• Be advised that it is normal for loud test tones to be
output during the “Auto Setup” procedure. Do not
allow small children to enter the room during the
procedure.
• To achieve the best results, make sure the room is as
quiet as possible while the “Auto Setup” procedure is
in progress. If there is too much ambient noise, the
results may not be satisfactory.
y
• See page 39 for the “Manual Setup” procedure.
• You can bring up the above menu screen from the setup menu (see
page 39).
Using Auto Setup
1
3
Check the following points.
Before starting the automatic setup, check the
following.
• All speakers and subwoofer are connected
properly.
• Headphones are disconnected from this unit.
• The video monitor is connected properly.
• This unit and the video monitor are turned on.
• This unit is selected as the video input source of the
video monitor.
• The connected subwoofer is turned on and the
volume level is set to about half way (or slightly
less).
• The crossover frequency controls of the connected
subwoofer are set to the maximum.
Optimizer microphone
y
• It is recommended that you use a tripod or something similar to fix the
optimizer microphone at the same height as your ears would be when
seated in your listening position. You can fix the optimizer microphone to
the tripod with the attaching screw of the tripod.
CROSSOVER/
HIGH CUT
VOLUME
4
MIN
MIN
MAX
MAX
Subwoofer
2
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
UT
VIDEO AUX
OPTIMIZER MIC
h
VIDEO
AUDIO
Place the optimizer microphone at your
normal listening position on a flat level
surface with the omni-directional
microphone heading upward.
PORTABLE
To select a sound character for adjustment,
press nCursor k to select “EQ Type” and
then press nCursor l / h.
If this unit does not work when you press nCursor,
press lSETUP once and then operate this unit.
This unit has a parametric equalizer that adjusts the
output levels for each frequency range. The equalizer
is adjusted to produce a cohesive sound field based on
automatically measured speaker characteristics.
In “EQ Type,” you can select the following
parametric equalizer characteristics suitable for the
desired sound characteristics.
Natural
This adjusts all speakers to achieve natural sound.
Select this if sounds in the high frequency range seem
too strong when “EQ Type” is set to “Flat.”
Optimizer microphone
18 En
Optimizing the speaker setting for your listening room (YPAO)
6
Front
This adjusts each speaker to obtain the same
characteristics as the front left and right speakers.
Select this if your front left and right speakers have
significantly better qualities than the other speakers.
5
1 AutoSetup
Notes
[SETUP]:Exit
The optimizer microphone is sensitive to heat. Store it
in a cool place and away from direct sunlight after
measurement. Do not leave it in a place where it will be
subjected to high temperatures such on an AV
component.
y
• If you do not want to apply the measurement results, select “Cancel.”
• Perform “Auto Setup” again if you change the number or positions of
speakers.
• If you press nENTER before removing the optimizer microphone,
“1 Auto Setup” of “Speaker Setup” in the setup menu (see page 39) is
displayed.
1 AutoSetup
RESULT
SP:3/4/0.1
DIST:8.0/8.5ft
LVL:-3.5/+4.5dB
.
>Set
Cancel
ADVANCED
OPERATION
When measurement is successfully completed,
“YPAO Complete” appears on the front panel display
and the results appear on the monitor.
PRESS[ENTER]
BASIC
OPERATION
Measurement takes about 3 minutes. To obtain precise
results, stay where you will not disturb the
measurement, such as to the side of or behind the
speakers or outside the room.
AUTOSETUPComplete
DisconnectMicrophone
PREPARATION
Press nCursor n to select “Start” and then
press nENTER to start the setup procedure.
A countdown starts and a measurement starts in 10
seconds. A loud test tone is output during
measurement.
• During the automatic setup procedure, do not perform any
operation on this unit.
• Press nCursor k to cancel the automatic setup procedure.
Press nENTER to confirm the settings.
The speaker characteristics are adjusted according to
measurement results.
To cancel the operation, press nCursor l / h to
select “Cancel” and press nENTER.
When the following screen appears, remove the
optimizer microphone. “Auto Setup” is now
complete.
INTRODUCTION
Flat
This adjusts each speaker to obtain the same
characteristics. Select this if your speakers have
similar qualities.
[]/[]:Select
p
[
[ENTER]:Finish
ADDITIONAL
INFORMATION
SP
Displays the number of speakers connected to this unit in
the following order:
Total of Front and Center/Total of Surround and Surround
Back/Subwoofer
DIST
Displays the speaker distance from the listening position
in the following order:
Closest speaker distance/Farthest speaker distance
APPENDIX
LVL
Displays the speaker output levels in the following order:
Lowest speaker output level/Highest speaker output level
Notes
English
• If “ERROR” appears on the video monitor during “Auto Setup,”
measurement is canceled and the type of error is displayed. For details,
see “When an error message is displayed during measurement”
(page 20).
• If problems occur during measurement, “WARNING (XX)” (xx indicates
the number of warning) appears above “RESULT” (see page 20).
19 En
Optimizing the speaker setting for your listening room (YPAO)
When an error message is displayed
during measurement
When a warning message is displayed
after measurement
Select “Retry” or “Exit” using nCursor l / h
and then press nENTER.
If a problem occurs during measurement, “WARNING” is
displayed on the result display screen. Check the error and
solve the problems.
ERROR
WARNING
.E-9:USER CANCEL
Don'toperate
any function
W-1:OUTOFPHASE
Reversechannel
FL--CENTER
SL--SBL--
>RetryExit
[]/[]:Select
p
[
[ENTER]:Return
Retry
Performs “Auto Setup” again.
Exit
Terminates the measurement and “Auto Setup.”
y
[ENTER]:Return
y
• See page 52 for details on warning messages.
• Optimization will not be performed while a warning message is
displayed. We recommend that you solve the problem and perform “Auto
Setup” again.
1
Check if “→” is displayed on the left of
“WARNING” and press nENTER.
Details of the warning message are displayed. If there
are multiple warning messages, you can display the
next message using nCursor h.
2
To return to the top result display, press
nENTER again.
• See page 51 for details on error messages.
• When “E-5:NOISY” appears, you can continue measurement. To
continue measurement, select “Proceed.” However, we recommend that
you solve the problem first and then perform measurement again.
20 En
BASIC OPERATION
Playback
Using the SCENE function
Turn on external components (TV, DVD
player, etc.) connected to this unit.
2
Press NINPUT l / h (or gInput
selection keys) to select an input source.
The name of the selected input source is displayed for
a few seconds.
Input source name
VOL.
AV1
Sound field program
BD/DVD
HDMI 1
Straight
TV
AV 1
Straight
CD
AV 3
Straight
RADIO
TUNER
7ch Enhancer
Volume
VOL.
Volume-18.5dB
L
SL
SW
C
R
SR
Note
Select the desired input source/sound field
program, and pressing down ISCENE (or
kSCENE) until “SET Complete” appears on the
front panel display.
While display in the OPTION menu or SETUP menu,
“SCENE Setting Complete” appears on the video monitor
(OSD).
Switching remotely controlled external
components linked to scene selections
You can operate an external component with the remote
control of this unit by setting a remote control code for the
external component for each input source. Setting remote
control codes for desired input sources allows you to
switch between external components linked to scene
selections.
1
Register the remote control code of an
external component to the desired input
source (see page 44).
Note
• Remote control codes cannot be registered to TUNER input.
English
1) When only noise is output
If a DTS bitstream signal is not properly input to this unit,
only noise is output. Connect the playback component to this
unit by digital connection and play back the DTS-CD. If the
condition is not improved, the problem may results from the
playback component. Consult the manufacturer of the
playback component.
Registering input source/sound field
program
APPENDIX
When you play back a DTS-CD, noise may be output in some
conditions, which may cause a speaker malfunction. Make sure
that the volume is set to low before starting playback. If noise is
output, do the following.
Press ISCENE (or kSCENE).
ADDITIONAL
INFORMATION
Turn the PVOLUME control to adjust the
volume (or press oVOLUME +/–).
Selecting a SCENE
ADVANCED
OPERATION
Play the external component that you have
selected as the source input, or select a radio
station on the tuner.
Refer to the operating instructions of the external
component for details on playback. For selecting
radio stations or playback of an iPod or Bluetooth
component using this unit, see the following.
• FM/AM radio tuning (see page 28)
• Bluetooth component playback (see page 32)
• iPod playback (see page 30)
• When this unit is on standby, you can turn on this unit by pressing the
SCENE key.
BASIC
OPERATION
• You can change the input source name displayed on the front panel
display or the OSD on the video monitor as necessary (see
page 43).
4
Input source
y
y
3
This unit has a SCENE function that allows you to change
input sources and sound field programs with one key. Four
scenes are available for different usages, such as playing
movies or music. The following input sources and sound
field programs are provided as the initial factory settings.
PREPARATION
1
INTRODUCTION
Basic procedure
2) When noise is output during playback or skip operation
Before playing back the DTS-CD, display the option menu
after selecting the input source and set “Decoder Mode” to
“DTS” (see page 33).
21 En
Playback
2
Press gInput selection keys on the
remote control for the input source whose
remote control code was registered in step 1
for about 3 seconds while pressing down
kSCENE key whose assignment you want
to change.
The external component can now be controlled
remotely just by selecting a scene.
Muting audio output temporarily
(MUTE)
1
2
Press qMUTE on the remote control to mute
the audio output.
The MUTE indicator on the front panel display
flashes while audio output is muted.
Enjoying pure hi-fi sound
Use Direct mode to enjoy the pure high fidelity sound of
the selected source. When Direct mode is activated, this
unit plays back the selected source with the least circuitry.
Press MDIRECT (or jDIRECT) to turn the
Direct mode on or off.
The following features are disabled in Direct mode.
– sound field program, tone control
– display and operation of the option menu and setup
menu
y
• While direct mode is on, the front panel display screen becomes dim.
When setting it back off, the brightness of the screen returns to the
previous setting.
Using the sleep timer
Press qMUTE again to resume audio
output.
The sleep timer is useful if you want to go to sleep while
this unit is playing or recording a source.
Adjusting high/low frequency sound
(tone control)
Press eSLEEP repeatedly to set the amount of
time.
Each time you press eSLEEP, the front panel display
changes as shown below.
You can adjust the balance of the high frequency range
(Treble) and low frequency range (Bass) of sounds output
from the front left and right speakers to obtain desired tone.
Sleep 120min.
Sleep Off
1
Press JTONE CONTROL on the front panel
repeatedly to select “Treble” or “Bass.”
The current setting is displayed on the front panel
display.
Treble
2
0.0dB
Adjust the frequency range using
KPROGRAM l / h.
Control range: –10.0 dB to +10.0 dB
The display returns the previous screen soon after you
release the key.
Notes
• The tone control settings are not effective during playback in direct
mode.
• If you set the balance extremely off, sounds may not match those from
other channels well.
22 En
Sleep 90min.
Sleep 30min.
Sleep 60min.
When the sleep timer is set, the SLEEP indicator on the
front panel display lights up.
Press eSLEEP on the remote control repeatedly until
“Sleep Off” appears on the front panel display.
Using your headphones
Plug your headphones in the BPHONES jack on
the front panel.
When you select a sound field program while using the
headphones, the mode is automatically set to SILENT
CINEMA mode.
Notes
• When you connect headphones, no signals are output at the speaker
terminals.
• When multi-channel signals are processed, sounds in all channels are
divided to left and right channels.
Playback
Displaying input signal information
y
• Input signal information is displayed on both a video monitor and the
front panel display.
• Information on the input signal is also displayed on the front panel
display. You can select the desired item using nCursor k / n.
1
Press nCursor k / n to select “Signal Info,”
and press nENTER.
Information on input signals is displayed. See
page 34 on messages displayed on the screen.
• If an HDMI related error occurs, error information is displayed at
the bottom of the screen.
• Information on the input signal is also displayed on the front panel
display. You can select the desired item using nCursor k / n.
3
To end the information display, press
mOPTION.
Straight
Sound field program (DSP program)
HDMI1-4:
AV1-6:
AUDIO1-2:
V-AUX:
FM/AM:
ADVANCED
OPERATION
Input, DSP Program, Audio Decoder
Input, DSP Program, Audio Decoder
Input, DSP Program, Audio Decoder
Input, DSP Program, Audio Decoder
Frequency, DSP Program, Audio
Decoder
iPod (Simple remote mode): Input, DSP Program, Audio Decoder
iPod (Menu browse mode): (in PlayInfo displayed) Artist, Album,
Song, DSP Program, Audio Decoder
(in Play menu displayed) List
Bluetooth:
Input, DSP Program, Audio Decoder
BASIC
OPERATION
Notes
Input source
PREPARATION
2
Select the desired input source, and press
mOPTION.
The option menu for the selected input source is
displayed (see page 33).
Information displayed on the front panel display can be
changed by pressing CINFO (or iINFO).
The following information can be displayed according to
the input source.
For example, if you select HDMI1 input and display “DSP
Program,” the following screen appears on the front panel
display.
INTRODUCTION
When HDMI1-4 or AV1-4 is selected as the input source,
you can display audio/video signal information.
Changing information on the front
panel display
ADDITIONAL
INFORMATION
APPENDIX
English
23 En
Enjoy the sound field programs
This unit is also equipped with a Yamaha digital sound field processing (DSP) chip. You can enjoy multi-channel sounds
for almost all input sources using various sound field programs stored on the chip and a variety of surround decoders.
Selecting sound field programs
■ Selecting a sound field program on the front panel
Press KPROGRAM l / h repeatedly to select a desired sound field program.
■ Selecting a sound field program with the remote control
Perform the following operations depending on the category of the sound field programs.
Sound field programs for movies/TV programs ...............................Press jMOVIE repeatedly.
Sound field programs for music........................................................Press jMUSIC repeatedly.
Stereo reproduction ...........................................................................Press jSTEREO repeatedly.
Multi-channel stereo reproduction ....................................................Press jSTEREO repeatedly.
Compressed music enhancer.............................................................Press jSTEREO repeatedly.
Surround decoder ..............................................................................Press jSUR.DECODE repeatedly.
For example, if you select “Sci-Fi” in “movie/TV program,” the following screen appears on the front panel display.
Sound field program category
Sci-Fi
Program name
Notes
• Sound field programs are stored for each input source. When you change the input source, the sound field program previously selected for that input
source is applied again.
• When you play back the Dolby Digital Plus, Dolby TrueHD, DTS Express, DTS-HD Master Audio, or DTS-HD High Resolution Audio sources, this unit
does not apply any sound field program other than the surround decoder and they are played back in straight decode mode.
• If the sampling frequency of an input source is higher than 96 kHz, this unit does not apply any sound field programs.
Sound field program descriptions
This unit provides sound field programs for multiple categories including music, movies and stereo reproduction. Select
a sound field program based on your listening preference, not merely on the name of the program, etc.
y
• You can check what speakers are currently outputting signals with the speaker indicators on the front panel display (see page 6).
• Each program can adjust sound field elements (sound field parameters). For details, see page 36.
•
in the table indicates the sound field program with CINEMA DSP.
For movie/TV program sources
Program
Descriptions
Standard
This program creates a sound field emphasizing the surrounding feeling without disturbing the original acoustic
positioning of multi-channel audio such as Dolby Digital and DTS. It has been designed with the concept of “an
ideal movie theater,” in which the audience is surrounded by beautiful reverberations from the left, right and rear.
Spectacle
This program represents the spectacular feeling of large-scale movie productions.
It reproduces a broad theater sound field matching the cinemascope and wider-screen movies with an excellent
dynamic range from very small to extremely large sound.
Sci-Fi
This program clearly reproduces the finely elaborated sound design of the latest science fiction and special effectsfeaturing movies.
You can enjoy a variety of cinematographically created virtual spaces reproduced with clear separation between
dialog, sound effects and background music.
Adventure
This program is ideal for precisely reproducing the sound design of action and adventure movies.
The sound field restrains reverberations but puts emphasis on reproducing a powerful space expanded widely to
the left and right. The reproduced depth is also restrained relatively to ensure the separation between audio
channels and the clarity of the sound.
24 En
Enjoy the sound field programs
Program
Descriptions
This program is provided for reproducing monaural video sources such as a classic movie in an atmosphere of a
good old movie theater.
The program produces the optimum expansion and reverberation to the original audio to create a comfortable
space with a certain sound depth.
Sports
This program allows the listeners to enjoy stereo sport broadcasts and studio variety programs with enriched live
feeling. In sports broadcasts, the voices of the commentator and sportscaster are positioned clearly at the center
while the atmosphere of the stadium expands in an optimum space to offer the listeners with a feeling of presence
in the stadium.
Action Game
This sound field has been suitable for action games such as car racing and FPS games. It uses the reflection data
that limits the effects range per channel in order to offer a powerful playing environment with a being-there feeling
by enhancing various effects tones while maintaining a clear sense of directions.
Roleplaying Game
This sound field has been suitable for role-playing and adventure games. It combines the sound field effects for
movies and the sound field designs for “Action Game” to represent the depth and 3D feeling of the field during
play, while offering movie-like surround effects in the movie scenes in the game.
For audio music sources
Program
Descriptions
This is an approximately 1700-seated, middle-sized concert hall with a shoebox shape that is traditional in Vienna.
Pillars and ornate carvings create extremely complex reflections from all around the audience, producing a very
full, rich sound.
Chamber
This program creates a relatively wide space with a high ceiling like an audience hall in a palace. It offers pleasant
reverberations that are suitable for courtly music and chamber music.
Cellar Club
This program simulates a live house with a low ceiling and homey atmosphere. A realistic, live sound field
features powerful sound as if the listener is in a row in front of a small stage.
The Roxy Theatre
This is the sound field of a rock music live house in Los Angeles, with approximately 460 seats. The listener’s
virtual seat is at the center left of the hall.
The Bottom Line
This is the sound field at stage front in The Bottom Line, that was a famous New York jazz club once. The floor
can seat 300 people to the left and right in a sound field offering real and vibrant sound.
Music Video
This sound field offers an image of a concert hall for live performance of pop, rock and jazz music. The listener
can indulge oneself in a hot live space thanks to the presence sound field that emphasizes the vividness of vocals
and solo play and the beat of rhythm instruments, and to the surround sound field that reproduces the space of a
big live hall.
For stereo reproduction
Program
2ch Stereo
Descriptions
APPENDIX
Hall in Vienna
ADDITIONAL
INFORMATION
This sound field simulates a concert hall with approximately 2500 seats in Munich, using stylish wood for the
interior finishing as normal standards for European concert halls. Fine, beautiful reverberations spread richly,
creating a calming atmosphere. The listener’s virtual seat is at the center left of the arena.
ADVANCED
OPERATION
Hall in Munich
BASIC
OPERATION
Mono Movie
PREPARATION
This sound field features stable reverberations that match a wide range of movie genres from serious dramas to
musicals and comedies. The reverberations are modest but offer an optimum 3D feeling, reproducing effects tones
and background music softly but cubically around clear words and center positioning in a way that does not fatigue
the listener even after long hours of viewing.
INTRODUCTION
Drama
Use this program to mix down multi-channel sources to 2 channels.
y
• When multi-channel signals (Dolby Digital and DTS) are input, they are downmixed to 2 channels and output from the front left and right speakers.
English
25 En
Enjoy the sound field programs
For Multi-channel stereo reproduction
Program
7ch Stereo
Descriptions
Use this program to output sound from all speakers. When you play back multi-channel sources, this unit
downmixes the source to 2 channels, and then outputs the sound from all speakers. This program creates a larger
sound field and is ideal for background music at parties, etc.
The Compressed Music Enhancer
Program
Descriptions
Straight Enhancer
Use this program to enhance the sound nearest to the original depth and width of the 2-channel or multi-channel
compression artifacts.
7ch Enhancer
Use this program to play back compression artifacts in 7-channel stereo.
Surround decode mode
Select this program to playback sources with selected decoders. You can playback 2-channel sources on multi-channels.
Decoder
Descriptions
Pro Logic
Dolby Pro Logic decoder suitable for all kinds of sources.
PLIIx Movie /
PLII Movie
Dolby Pro Logic IIx (or Dolby Pro Logic II) decoder suitable for movies. If your listening environment is as
follows, you cannot select the Dolby Pro Logic IIx decoder.
• When the surround back speakers are not connected
• When headphones are connected
PLIIx Music /
PLII Music
Dolby Pro Logic IIx (or Dolby Pro Logic II) decoder suitable for music. If your listening environment is as
follows, you cannot select the Dolby Pro Logic IIx decoder.
• When the surround back speakers are not connected
• When headphones are connected
PLIIx Game /
PLII Game
Dolby Pro Logic IIx (or Dolby Pro Logic II) decoder suitable for games. If your listening environment is as
follows, you cannot select the Dolby Pro Logic IIx decoder.
• When the surround back speakers are not connected
• When headphones are connected
Neo:6 Cinema
DTS decoder suitable for movies.
Neo:6 Music
DTS decoder suitable for music.
y
• An input source is played back in straight decode mode (see page 27) when multi-channel audio signal is input.
26 En
Enjoy the sound field programs
Enjoying unprocessed input sources
(Straight decoding mode)
To enable straight decoding mode, press
LSTRAIGHT (or jSTRAIGHT).
“Straight” appears on the front panel display.
2
To cancel straight decoding mode, press
LSTRAIGHT (or jSTRAIGHT) again.
A sound field program name appears on the front
panel display, and sound is reproduced with that
sound field effect.
Note
• SILENT CINEMA mode is not available in the following conditions.
– 2ch Stereo of the sound field program is selected.
– direct mode or straight decoding mode is selected.
PREPARATION
1
SILENT CINEMA allows you to enjoy multi-channel
sources with your headphones. SILENT CINEMA mode
is automatically selected when you connect the headphone
plug to the PHONES jack.
INTRODUCTION
In straight decoding mode, sounds are reproduced without
sound field effect. 2-channel stereo sources are output
from only the front left and right speakers. Multi-channel
input sources are decoded straight into the appropriate
channels and multi-channel sounds are reproduced
without a sound field effect.
Enjoy sound field programs with
headphones (SILENT CINEMA™)
BASIC
OPERATION
Enjoying sound field programs without
surround speakers (Virtual CINEMA
DSP)
ADVANCED
OPERATION
Virtual CINEMA DSP allows you to enjoy DSP sound
field surround effects even without any surround speakers
by using virtual surround speakers. You can even enjoy
Virtual CINEMA DSP using a minimal two-speaker
system that does not include a center speaker.
When “Sur. L/R SP” in the setup menu is set to “None”
(see page 40), this unit operates in Virtual CINEMA DSP
mode.
Note
ADDITIONAL
INFORMATION
• Virtual CINEMA DSP mode is not available in the following conditions
even if you set “Sur. L/R SP” to “None” (see page 40).
– headphone plug is connected to the PHONES jack.
– 7ch Stereo of the field sound program is selected.
– direct mode or straight decoding mode is used.
APPENDIX
English
27 En
FM/AM tuning
The FM/AM tuner of this unit provides the following two
modes for tuning.
■
Frequency tuning mode (Auto tuning /
Manual tuning)
You can tune in to a desired FM/AM station by searching
or specifying its frequency.
y
• You can switch between stereo and monaural for FM broadcast in the
option menu (see page 34).
4
■ Preset tuning mode (Preset tuning)
You can preset the frequencies of FM/AM stations by
registering them to specific numbers, and later just select
those numbers to tune in.
Note
• “Wrong Station!” appears on the front panel display when you
enter a frequency that is out of receivable range. Make sure that the
entered frequency is correct.
Note
• Adjust the FM/AM antennas connected to this unit for the best reception.
Tuning in to the desired FM/AM station
(Frequency tuning)
1
Press NINPUT l / h (or gTUNER)
repeatedly and switch the input source to
“TUNER.”
2
Press FFM (hFM) or GAM (hAM) to select
a band.
“FM” or “AM” appears on the front panel display
according to the band that you have selected.
3
Press HTUNING l / h (or hTUNING k /
n) to specify the frequency.
To adjust the frequency to a higher range, press h (or
k). To adjust it to the lower range, press l (or n).
The TUNED indicator on the front panel display
lights up when the tuner is tuned in to a station. The
STEREO indicator also lights up if the program being
broadcasted is in stereo.
STEREO
TUNED
FM92.5MHz
To tune in by direct frequency tuning, enter
the frequency of the desired station using
the numeric keys on the remote control.
Enter only integers. For example, if you want to set
the frequency to 88.9 MHz, enter “889” using
sNumeric keys.
Registering FM/AM stations and
tuning in (Preset tuning)
You can register up to 40 FM/AM stations (Preset) using
“Automatic station preset” or “Manual station preset.”
Registering stations by automatic station
preset
The tuner automatically detects FM stations with strong
signals and registers up to 40 stations. AM stations cannot
be automatically registered. Use manual station preset.
1
Press NINPUT l / h repeatedly (or press
gTUNER) to switch the input source to
“TUNER.”
2
Press mOPTION on the remote control.
The option menu screen for setting options of tuner
input appears on the front panel display.
y
• For details on the option menu, see page 33.
• The option menu is displayed on monitor components.
3
Select “Auto Preset,” and press nENTER.
The frequency changes in the following manner according
to how you press HTUNING l / h (or hTUNING k
/ n).
When you press the key more than 1 second
The tuner searches the frequency of a station that is
detectable around the current frequency. This is effective
when the tuner can receive strong signals without any
interference. Once the search starts, release the key.
When you keep holding the key, the search continues even
when a station is detected. This is useful when you want to
tune in to a specific station.
When you press and release the key
The tuner increases or decreases the frequency in steps.
Use this method when the tuner cannot receive strong
signals and stations are skipped during the search. You can
listen to better quality sound even when the tuner cannot
receive a strong signal.
28 En
Auto Preset
Automatic station preset starts about 5 seconds later
from the lowest frequency upwards.
y
• You can select the preset number at which the preset starts by
pressing hPRESET k / n or nCursor k / n while the front
panel display is in the state as shown in the below figure.
• To cancel registration, press nRETURN on the remote control.
Status
01:FM87.5MHz
Preset number
Frequency
FM/AM tuning
Registering stations by manual station
preset
1
2
Tune in to a station referring to “Tuning in to
the desired FM/AM station (Frequency
tuning)” (see page 28).
Press EPRESET l / h (or hPRESET k / n) to
select a preset number.
y
• Preset numbers to which no stations are registered will be skipped.
• When “No Presets” or “No Presets in Memory” is displayed it means that
no stations are registered. See page 28 and register stations.
• You can directly select a preset number by pressing a sNumeric
keys while calling a preset station. “Empty” appears on the display if
you enter a preset number to which no station is registered. “Wrong
Num.” appears if you enter an invalid number.
Clearing the preset station
1
Press NINPUT l / h repeatedly (or press
gTUNER) to switch the input source to
“TUNER.”
2
Press mOPTION on the remote control.
The option menu screen for setting options of tuner
input appears on the front panel display.
3
Display “Clear Preset” using the nCursor k
/ n and press nENTER.
The following screen appears on the display.
y
• By pressing down DMEMORY (or hMEMORY) for more
than 2 seconds, you can skip step 3 and register the preset number
to be one higher than the last preset number.
3
01:FM92.5MHz
Preset number of the registered station you want to clear.
• You can cancel the operation and return to the option menu screen
by pressing nRETURN on the remote control.
4
Flashing
Preset
number
Empty (or frequency that is currently
registered to the preset number)
y
• You can select a preset number using the sNumeric keys.
APPENDIX
4
Select the preset number of the registered
station you want to clear using the nCursor
k / n and press nENTER.
The preset station registered to the selected preset
number is cleared. To clear the registration of
multiple preset numbers, repeat the above steps.
To end the operation, press mOPTION.
ADDITIONAL
INFORMATION
y
New registered frequency
01:Empty
ADVANCED
OPERATION
Press EPRESET l / h (or hPRESET k / n)
on the remote control to select the preset
number to which the station will be
registered.
When you select a preset number to which no station
is registered, “Empty” appears on the display. When
you select a registered preset number, a registered
frequency is displayed on the right of the preset
number.
BASIC
OPERATION
Press DMEMORY (or hMEMORY).
“Manual Preset” appears on the front panel display,
followed soon by the preset number to which the
station will be registered.
You can call preset stations registered by automatic station
preset or manual station preset.
PREPARATION
You can manually register AM stations or FM stations
with weak signals.
Calling a preset station (Preset tuning)
INTRODUCTION
During the automatic station preset, the upper area of
the screen changes as follows: READY → SEARCH
→ MEMORY each time a station is registered.
When registration is complete, “FINISH” appears
and the option menu screen automatically reappears.
When you press mOPTION on the remote control,
the screen returns to the original state.
Press DMEMORY (or hMEMORY) again to
register.
When registration is complete, the screen returns to
the original state.
To end the operation, press mOPTION.
y
• To cancel registration, press nRETURN on the remote control
or leave the tuner without any operations for about 30 seconds.
English
29 En
Using iPod™
Once you have stationed your iPod in a Yamaha iPod universal dock (such as the YDS-11, sold separately) connected to
the DOCK terminal on the rear panel of this unit (see page 16), you can enjoy playback of your iPod using the supplied
remote control or the menu displayed on the video monitor. You can also use the Compressed Music Enhancer mode of
this unit to improve the sound quality of the compression artifacts (such as MP3 format) stored on your iPod (see
page 24).
Notes
• iPod touch, iPod (Click and Wheel including iPod classic), iPod nano, and iPod mini are supported.
• Some features may not be compatible depending on the model or the software version of your iPod.
• Some features may not be available depending on the model of Yamaha iPod universal dock. The following sections describe the procedure when using
the YDS-11.
y
• Once the connection between your iPod and this unit is complete, “iPod connected” appears on the front panel display.
• For a complete list of status messages that appear on the front panel display and on the video monitor, see the “iPod” section on page 50.
Controlling iPod in menu browse mode
Controlling iPod™
You can control your iPod when you set it in the iPod
universal dock and switch the input source to DOCK. The
operations of your iPod can be done with the aid of the
video display (menu browse mode) or without it (simple
remote mode).
When you connect your iPod to this unit, you can perform
the following operations with the remote control.
Key
ENTER
n
r
p
Function
Subsequent menu
k
Menu up
n
Menu down
l
Previous menu
h
Subsequent menu
w
Search backward (Press and hold)
f
Search forward (Press and hold)
a
Skip forward
b
Skip backward
s
Stop
e
Pause (Menu browse mode)
Play/Pause (Simple remote mode)
p
Play (Menu browse mode)
Play/Pause (Simple remote mode)
DISPLAY
Switch between Menu browse mode and
Simple remote mode
Controlling iPod in simple remote mode
You can perform basic iPod operations (play, stop, skip,
etc.) using the supplied remote control without displaying
the menu on the video monitor. You can also directly
control your iPod in this mode.
30 En
You can perform advanced iPod operations using the
remote control while looking at the menu displayed on the
video monitor. You can browse the song files or video files
stored on your iPod and displayed on the monitor, and
change the settings of your iPod to suit your personal
preferences. You cannot directly control your iPod in this
mode.
y
• “_”(underscore) is displayed for characters that this unit cannot display.
1
Change the input source to “iPod (DOCK)”
using NINPUT l / h (or gDOCK).
2
Press pDISPLAY on the remote control.
The following screen appears on the video monitor.
iPodTop
Music>
Videos>
3
Press nCursor k / n to select “Music,”
“Videos” or “Settings” and press nCursor
h.
• Select “Music” to browse music files.
• Select “Videos” to browse video files.
Note
• “Videos” will not be displayed when your iPod or Yamaha iPod
universal dock do not support the browser function for browsing
video files.
Using iPod™
4
Shuffle/repeat playback
You can use a special playback function such as shuffle
playback and repeat playback by setting the option menu.
Press pDISPLAY to switch to menu browse
mode while “DOCK” is selected as the input
source.
The option menu can be displayed only in menu
browse mode. Press pDISPLAY to switch to menu
browse mode before starting shuffle or repeat
playback.
Menu items of “Videos”
Menu items vary depending on the files stored on
your iPod.
2
Press mOPTION.
The option menu is displayed.
3
Press nCursor k / n to select the desired
playback function, Shuffle or Repeat, then
press nENTER.
The following playback styles are available
depending on the playback function selected.
Description of the play information display
g
b
c
d
e
f
Shuffle: Plays back songs or albums in random
order (Choices: Off, Songs, Albums).
• Select “Off” if you do not want to play back in
random order.
• Select “Songs” to play back songs in random order.
• Select “Albums” to play back albums in random
order.
i
Repeat: Plays back songs or albums repeatedly
(Choices: Off, One, All).
• Select “Off” if you do not want to play back
repeatedly.
• Select “One” to repeat each song.
• Select “All” to repeat all songs.
(search forward) and
4
y
• You can change information screens on the front panel display using
CINFO (or iINFO) (see page 23). Items displayed on the front panel
display vary depending on mode that is currently selected.
Select the desired style using nCursor l /
h.
The style is selected. Playback starts with the
function selected in step 3.
To return to the previous screen, press nRETURN.
To return to the previous playback function, redo the
above steps.
ADDITIONAL
INFORMATION
a Track number/total tracks
b Artist name
c Album title
d Song title
e Progress bar
f Elapsed time
g Shuffle and repeat icons
h
(playback),
(pausing),
(search backward)
i Remaining time
h
ADVANCED
OPERATION
iPod[Play]
1/9
FrankieZipper
Made-to-order
RoadtoIndia
|||||;;;;;;;;;;;;;;;
0:51-7:44
All
a
BASIC
OPERATION
1
PREPARATION
Menu items of “Music”
Playlists, Artists, Albums, Songs, Genres, Composers
• Playlists > Songs
• Artists > Albums > Songs
• Albums > Songs
• Songs
• Genres > Artists > Albums > Songs
• Composers > Albums > Songs
INTRODUCTION
■
Press nCursor k / n / l / h to select a
menu item and then nENTER to start
playback.
y
APPENDIX
• When the shuffle function is on, “
” appears on the video monitor.
• When “Repeat” is set to “One” or “All,” “ 1 ” or “ All ” appears on the
video monitor.
English
31 En
Using Bluetooth™ components
You can connect a Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) to the DOCK terminal of
this unit and enjoy the music contents stored in your Bluetooth component (such as a portable music player) without
wiring between this unit and the Bluetooth component. You need to perform “Pairing” the connected Bluetooth wireless
audio receiver and your Bluetooth component in advance.
Note
• This unit supports A2DP (Advanced Audio Distribution Profile) of the Bluetooth profile.
Pairing the Bluetooth™ wireless audio
receiver and your Bluetooth
component
“Pairing” refers to the operation of registering a Bluetooth
component for Bluetooth communications. Pairing must
be performed when using a Bluetooth component with the
Bluetooth wireless audio receiver connected to this unit
for the first time or if the pairing data has been deleted.
5
Make sure the Bluetooth component
recognizes the Bluetooth wireless audio
receiver.
If the Bluetooth have recognized the Bluetooth
wireless audio receiver, “YBA-10 YAMAHA,” for
instance, is displayed in the Bluetooth device list.
6
Select the Bluetooth wireless audio receiver
from the Bluetooth device list, and enter a
path key “0000” into the Bluetooth
component.
When pairing is complete, “Completed” appears on
the front panel display.
y
• You only need the pairing operation for the first time that you use the
Bluetooth component with the Bluetooth wireless audio receiver.
• Pairing requires operations on this unit and on the other component with
which Bluetooth communications are to be established. If necessary,
refer to the other component’s operating instructions.
■
Pairing the Bluetooth™ wireless audio
receiver and your Bluetooth™ component
To ensure security, a time limit of 8 minutes is set for
the pairing operation. You are recommended to read
and fully understand all the instructions before starting.
y
• The Yamaha Bluetooth wireless audio receiver can be paired with up to
eight Bluetooth components. When pairing is conducted successfully
with a ninth component and the pairing data is registered, the pairing data
for the least recently used other component is cleared.
Playback of the Bluetooth™
component
1
Change the input source to “DOCK” using
NINPUT l / h (or gDOCK).
1
Change the input source to “DOCK” using
NINPUT l / h (or gDOCK).
2
Turn on the Bluetooth component you want
to pair with and set it to pairing mode.
For details on operation of the Bluetooth component,
refer to its operating instructions.
2
Press mOPTION.
3
Press nCursor n repeatedly to select
“Connect” and press nENTER.
After you execute “Connect,” communication with
the Bluetooth component is established. When the
connected Bluetooth wireless audio receiver
recognizes the Bluetooth component, “BT
Connected” appears on the front panel display.
3
Press mOPTION.
The option menu for DOCK input appears on the
video monitor.
y
DOCKOPTION
• When you press nENTER on the remote control, the connected
Bluetooth wireless audio receiver searches and connects to the last
connected Bluetooth component. If the Bluetooth wireless audio
receiver cannot find the Bluetooth component, “Not found”
appears on the front panel display.
• To disconnect the Bluetooth wireless audio receiver from the
Bluetooth component, display the option menu again, select
“Disconnect,” and press nENTER.
.VolumeTrim
Connect
Pairing
4
[
[
[]/[]:Up/Down
[ENTER]:Select
Press nCursor n to select “Pairing” and
press nENTER.
“Searching” appears on the front panel display and
the pairing operation starts.
y
• To cancel pairing, press nRETURN.
• You can also start pairing operation by pressing and holding
DMEMORY on the front panel.
32 En
4
Start playback of the Bluetooth component.
ADVANCED OPERATION
Setting the option menu for each input source (OPTION menu)
Select an input source using NINPUT l / h
(gInput selection keys).
2
Press mOPTION on the remote control.
The OPTION menu appears. The displayed OPTION
menu items differ depending on the input source. For
details, see the following section.
OPTION menu items
The following menu items are provided for each input
source.
Input
Source
Volume
Trim
Decoder
Mode
Extended
Surround
Signal Info
AV1-4
Volume
Trim
Decoder
Mode
Extended
Surround
Signal Info
AV5-6
Volume
Trim
AUDIO1-2
Volume
Trim
V-AUX
Volume
Trim
TUNER
Volume
Trim
FM Mode
Auto
Preset
Clear
Preset
iPod
(DOCK)
Volume
Trim
Shuffle
Repeat
Bluetooth
(DOCK)
Volume
Trim
Connect/
Disconnect
Pairing
3
4
Select the desired menu item using
nCursor k / n, and press nENTER.
Parameters of the selected menu item are displayed.
Change the setting of the selected menu item
(or enable a function) using nCursor k / n /
l / h and nENTER.
Details of the selected menu item are displayed.
Parameters you can set differ depending on the menu
items.
Details of the menu items are as follows:
y
Input source:
All
Adjustable range: -6.0 dB to 0.0 dB* to +6.0 dB
(in 0.5 dB steps)
• When nCursor or other keys do not work after completing the
menu, select the input source again using gInput selection
keys.
y
• The default settings are marked with “*.”
■
Volume Trim
Reduces any change in volume when switching input
sources by correcting volume differences between input
sources.
You can set this parameter for each input source.
ADDITIONAL
INFORMATION
To close the OPTION menu, press
mOPTION.
You can also use nRETURN to return to the
previous screen or close the OPTION menu.
ADVANCED
OPERATION
5
[
[
[]/[]:Up/Down
[ENTER]:Select
BASIC
OPERATION
HDMI1-4
HDMI1OPTION
.VolumeTrim
DecoderMode
ExtendedSurround
SignalInfo
Menu item
PREPARATION
1
INTRODUCTION
This unit has an OPTION menu of frequently used menu items for input sources compatible with this unit. The procedure
for setting the OPTION menu items is described below.
APPENDIX
English
33 En
Setting the option menu for each input source (OPTION menu)
■
Decoder Mode
Input source: HDMI1-4, AV1-4
Choices:
Auto*/DTS
Selects DTS digital audio signals for reproduction.
Auto
DTS
■
Automatically selects audio input signals.
Selects DTS signals only. Other input signals
are not reproduced.
Extended Surround
Input source: HDMI1-4, AV1-4
Choices:
Auto*/PLIIxMovie/PLIIxMusic/EX/ES/
Off
Selects whether to reproduce multi-channel input signals
in 6.1- or 7.1-channel when surround back speakers are
used.
Auto
PLIIx
Movie
PLIIx
Music
EX/ES
Off
Automatically selects the most suitable
decoder according to whether a flag for
reproducing surround back channel is present,
and reproduces the signals in 6.1- or 7.1channel.
Always reproduces signals in 6.1- or 7.1channel using the PLIIxMovie decoder
whether or not surround back channel signals
are contained. You can select this parameter
when one or two speakers are connected.
Always reproduces signals in 6.1- or 7.1channel using the PLIIxMusic decoder whether
or not surround back channel signals are
contained. You can select this parameter when
one or two speakers are connected.
Automatically selects the most suitable
decoder for input signals whether or not the
flag for reproducing surround back channel is
present, and always reproduces signals in 6.1channel.
Always reproduces signals in 5.1-channel
whether or not the flag for reproducing
surround back channel is present.
■
Signal Info
Input source: HDMI1-4, AV1-4
Displays information on audio and video signals on the
video monitor and front panel display. You can change
information to be displayed on the front panel display
using nCursor k / n.
Signal Info parameters
■
Audio information
Information
Description
Format
Format of digital audio signals.
Channel
The number of input signal channels (front/
surround/LFE).
For example, if input signal channels are 3
front channels, 2 surrounds and LFE, “3/2/
0.1” is displayed.
If a channel that cannot be expressed as the
above, a total number of channels such as
“5.1ch” may be displayed.
Sampling
The sampling frequency per second in
analog-to-digital conversion.
Bitrate
The bit rate of input signal per second.
Notes
• “No Signal” is displayed when no signals are input and “---” is displayed
when signals that this unit cannot recognize are input.
• The bit rate may vary during playback.
■
Video information
Information
Description
In
Format and resolution of video input signal.
Out
Format and resolution of video output signal.
Message
Error messages about HDMI signals and
HDMI components. See the following for
details of the error messages.
HDMI error message
(appears only when an error has occurred)
HDCP authentication failed.
HDCP Error
Device Over The number of HDMI components connected is
Out of Res.
■
over the limit.
The connected monitor is not compatible with
the video input signal.
FM Mode
Input source: TUNER
Choices:
Stereo*/Mono
Sets FM broadcasting receiving mode.
Stereo Receives in stereo mode.
Mono
Receives in monaural mode. You can get better
reception in MONO mode.
34 En
Setting the option menu for each input source (OPTION menu)
■
Auto Preset
Input source: TUNER
■
INTRODUCTION
Automatically detects radio stations in the FM frequency
band and registers them as preset stations (see page 28).
Clear Preset
Input source: TUNER
Clears the preset stations (see page 29).
■
Shuffle
Input source: iPod (DOCK)
Choices:
Off*/Songs/Albums
■
PREPARATION
Changes the shuffle playback style (see page 31).
Repeat
Input source: iPod (DOCK)
Choices:
Off*/One/All
Changes the repeat playback style (see page 31).
■
Connect / Disconnect
Input source: Bluetooth (DOCK)
■
BASIC
OPERATION
Switches communication with a Bluetooth component on
and off (see page 32).
Pairing
Input source: Bluetooth (DOCK)
Performs pairing of this unit and a Bluetooth component
(see page 32).
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
English
35 En
Editing surround decoders/sound field programs
Selecting a decoder used with a sound
field program
5
When using sound field programs for movies or TV
programs (except for Mono Movie), you can select a
surround decoder to be used with the sound field program
after setting the parameters from the following decoders.
To set the parameters for sound field programs, see the
following section.
Decoders that can be used with a sound field
program
• PLIIx Movie (PLII Movie)
• Neo:6 Cinema
Setting sound field parameters
Although the field sound programs would satisfy you as
they are with the default parameters, you can arrange
sound effect or decoders suitable for acoustical conditions
of sources or rooms by setting the parameters (sound field
elements).
y
• You can protect the sound field against the changes of parameters the
sound filed parameters when “Memory Guard” of the setup menu is set
to “On” (see page 43). To change the parameters, set it to “Off.”
1
Turn on the video monitor connected to this
unit.
2
Press lSETUP on the remote control.
The setup menu appears on the monitor.
3
Press nCursor k / n to select “DSP
Parameter” and press nENTER.
The screen changes as follows.
Sound field program
MOVIE
.Sci-Fi
SUR.;;;;PLII Movie
DSP Level;;;;;0dB
Initialize
p
Cursor
[
[]/[]:Select
Sound field parameters
4
Set values
Press nCursor k / n to move “→” to the
sound field program and press nCursor l /
h to select the sound field program.
36 En
Press nCursor k / n to select the parameter
that you want to change, and press nCursor
l / h to change the parameter.
An asterisk (*) appears on the left of the sound field
parameter name displayed on the monitor when you
change the parameter from its default setting. For
details on functions and adjustable ranges of the
sound field parameters, see “Sound field parameters”
on this page.
y
• Repeat steps 4 and 5 to change other sound field program
parameters.
6
To end the edit, press nRETURN.
To initialize the parameters of the selected sound field
program, nCursor n repeatedly to select “Initialize”
and then press, nCursor h. When the confirmation
screen appears on the monitor, press nCursor h to
confirm the initialization or nCursor l to cancel it.
Sound field parameters
y
• The default settings are marked with “*.”
CINEMA DSP parameters
DSP Level
Adjustable range: -6 dB to 0 dB* to +3 dB
Fine adjusts an effect level (level of the sound field effect
to be added). You can adjust the level of the sound field
effect while checking sound levels. Adjust “DSP Level” as
follows.
• The effect sound is too soft.
• There are no differences between effects of the sound
field programs.
→Increase the effect level.
• The sound is dull.
• The sound field effect is added too much.
→Reduce the effect level.
Editing surround decoders/sound field programs
Parameters only usable in certain sound
field programs
2ch Stereo only
■
Direct
Choices:
Auto*/Off
Automatically bypasses the DSP circuit and tone control
circuit when an analog sound source is selected as the
input source. You can enjoy a higher quality sound.
7ch Stereo only
CT Level/SL Level/SR Level/
SB Level
Adjusts the volume of the center (CT), surround L (SL)
surround R (SR) and surround back (SB) channels in the
7ch Stereo program. The available parameters differ
depending on the setting of the speakers.
■
Straight Enhancer/7ch Enhancer only
Choices:
High*/Low
Adjusts the Compressed Music Enhancer effect level.
When the high-frequency signals of the source is
emphasized too much, set the effect level to “Low.” To
reduce the effect, set this parameter to “Low.” To increase
the effect, set it to “High.”
Choices:
Off*/On
Adjusts the soundscape of the front sound field. Sends
stereo signals to the surround speakers as well as the front
speakers for a wraparound effect.
Dimension
Adjustable range: -3 to STD* to +3
Adjusts the difference in level between the front sound
field and the surround sound field. You can adjust the
difference in level created by the software being played
back to obtain the preferred sound balance. The surround
sound gets stronger as you make the value more negative
and the front sound gets stronger as you make the value
more positive.
Center Width
Adjustable range: 0 to 3* to 7
You can spread the center sound toward left and right
according to your preference. Set this parameter to 0 for
outputting the center sound from the center speaker only,
or to 7 for outputting it from the front left/right speaker.
■
When Neo:6 Music is selected
C.Image
Adjustable range: 0.0 to 0.3 to 1.0
Adjusts the front left and right channel output relative to
the center channel to make the center channel more or less
dominant as necessary.
ADVANCED
OPERATION
Effect Level
Panorama
BASIC
OPERATION
Adjustable range: 0 to 100%
When PLIIx Music/PLII Music is selected
PREPARATION
Auto Outputs sound by bypassing the DSP circuit and
tone control circuit when the “Bass” and “Treble”
tone controls are both set to 0 dB.
Off Do not bypass the DSP circuit and tone control
circuit.
■
You can customize decoder effects by setting the
following parameters. For kinds of decoders, see page 26.
INTRODUCTION
■
Decoder parameters
ADDITIONAL
INFORMATION
APPENDIX
English
37 En
Operating various settings for this unit (Setup menu)
You can call the setup menu using the remote control and change the settings of various menus.
You can change the following settings in the setup menu. For details, read “Basic operation of the setup menu” first, and
see the respective pages.
Menu/Submenu
Speaker Setup
Function
Page
Sets items for speakers.
39
1 Auto Setup (YPAO)
Automatically adjusts output characteristics of speakers.
39
2 Manual Setup
Manually adjusts output characteristics of speakers.
39
A)Config
Sets speaker configurations, such as connection status of speaker and a size of the
connected speaker (sound reproduction capacity), suitable for the listening
environment.
39
B)Level
Separately adjusts volume of each speaker.
41
C)Distance
Adjusts timing at which each speaker outputs sound based on distances between
speakers and the listening position.
41
D)Equalizer
Selects an equalizer that adjusts speaker output characteristics.
41
E)Test Tone
Generates test tones.
41
Sets various items for sound outputs.
41
1 Dynamic Range
Adjusts dynamic ranges of speakers and headphones.
41
2 Lipsync
Adjusts delay in output timing between video signals and audio signals.
41
Sets on or off of automatic adjustments for delay between output timing between
video signals input from the HDMI jack and audio signals.
41
Auto Delay
Fine adjusts a delay time of HDMI Auto.
42
Manual Delay
Manually fine adjusts the delay of audio and visual output.
42
Sound Setup
HDMI Auto
Function Setup
Set various items for HDMI and display.
42
Sets various items for input sources.
42
Standby Through
Selects on or off of output of HDMI signals input from the HDMI IN jack to the
HDMI OUT jack when this unit is on standby.
42
Audio Output
Selects this unit or a component connected to this unit via the HDMI OUT jack of
this unit for reproducing sound signals input from the HDMI IN jack.
42
Resolution
Sets resolution of the HDMI output that is converted from analogy visual input
signals.
42
Aspect
Set an aspect ratio of images reproduced by HDMI signals converted from analog
video input signals.
42
Set items for a monitor or the front panel display.
42
Dimmer
Sets brightness of the front panel display.
42
FL Scroll
Selects the way to display characters on the front panel display.
42
OSD Shift
Adjusts top and bottom positions of the screen displayed on the video monitor.
43
Sets items for volumes.
43
Adaptive DRC
Adjust the dynamic range (difference between the maximum volume and the
minimum volume) in conjunction with the volume level.
43
Max Volume
Sets the maximum volume level so that the volume will not be accidentally
increased.
43
Sets the volume at the time this unit is turned on.
43
Changes input source names to be displayed on a video monitor or the front panel
display.
43
1 HDMI
2 Display
3 Volume
Init. Volume
4 Input Rename
DSP Parameter
Sets parameters for the sound field programs.
43
Memory Guard
Protects some settings against accidental alteration.
43
38 En
Operating various settings for this unit (Setup menu)
“A)Config” display (example)
Basic operation of the setup menu
A)Config
The setup menu screen appears on both video display
(OSD) and front panel display.
Center SP
INTRODUCTION
Video display (OSD)
SetupMenu
. ;SpeakerSetup
;SoundSetup
;FunctionSetup
;DSPParameter
;MemoryGuard
y
• You can change other items by repeating step 4.
5
To finish the setting, press lSETUP.
[
y
• When nCursor or other keys do not work after completing the menu,
select the input source again using gInput selection keys.
Front panel display
Speaker Setup
;SpeakerSetup
Press lSETUP on the remote control.
The setup menu screen appears.
y
2
Select a menu using nCursor k / n, and
press nENTER.
Items of the selected menu are displayed. For
example, the following screen appears when you
select “Function Setup.”
;FunctionSetup
. 1HDMI
2Display
3Volume
4InputRename
[
y
• You can return to the previous screen by pressing nRETURN.
3
To display submenus, select a menu that you
want to set using nCursor k / n, and press
nENTER.
For example, the following screen appears when you
select “2 Display.”
. Dimmer;;;;;;;;;;;;0
FLScroll;;Continue
OSDShift;;;;;;;;;0
Automatically adjusts output characteristics of speakers to
obtain optimum balance for the output sound based on
positions and performances of the speakers and acoustic
characteristics or the room, which are automatically
measured. For details on operations, see page 18.
2 Manual Setup
Adjusts output characteristics of speakers based on
manually set parameters.
After Auto Setup (YPAO) is performed, you can check
automatically adjusted parameters in the Manual Setup
menu. Fine adjust the parameters for your preference if
necessary.
■ A)Config
Sets speaker configurations, such as connection status of
speaker and a size of the connected speaker (sound
reproduction capacity), suitable for the listening
environment.
y
• The speaker configuration includes items for defining a speaker size:
Large or Small. Large and Small refer to speakers with woofer diameters
16 cm or larger and smaller than 16 cm, respectively.
LFE/Bass Out
Choices:
[
4
[
[]/[]:Up/Down
[]/[]:Adjust
[ [
Selects speaker(s) for outputting low-frequency
components of the LFE (low-frequency effect sound)
channel or other channels. The output status is as follows.
English
Select an item using nCursor k / n, and
change the setting of the item using
nCursor l / h.
Some items in the Manual Setup menu of Speaker
Setup take up a full screen. To display other items in
the Manual Setup menu, press nCursor k / n.
SWFR/Front/Both*
APPENDIX
2Display
1 Auto Setup
ADDITIONAL
INFORMATION
[
[]/[]:Up/Down
[ENTER]:Enter
• The default settings are marked with “*.”
ADVANCED
OPERATION
1
BASIC
OPERATION
In this section, procedures of setting menus using the
video monitor are described.
You can set various items for speakers. Two kinds of
adjustments are available. One is “Auto Setup (YPAO)”
for automatic adjustment and another is “Manual Setup”
for manual adjustment.
PREPARATION
[
[]/[]:Up/Down
[ENTER]:Enter
None >Small Large
39 En
Operating various settings for this unit (Setup menu)
Sur. L/R SP
LFE channel signals
Parameter
Front
speakers
Subwoofer
Other
speakers
Both
Output
Not output
Not output
SWFR
Output
Not output
Not output
Front
Not output
Output
Not output
Low-frequency components of other channel signals
Parameter
Front
speakers
Subwoofer
Choices:
None
Small
Other
speakers
Both
[1]
[2]
[3]
SWFR
[4]
[3]
[3]
Front
Not output
[1]
[3]
None/Small*/Large
Sets sizes of left and right surround speakers.
Large
Select this when no surround speakers are
connected. Surround channel signals are
spread to front left and right speakers. “Sur.B
L/R SP” automatically switches to “None”
when this is selected.
Select this when small surround speakers are
connected. Low-frequency components of
surround channels are output from a
subwoofer. If a subwoofer is not connected
they are output from front speakers.
Select this when large surround speakers are
connected.
y
[1]
[2]
[3]
[4]
Outputs low-frequency components of the front left and right
channels and the channel of speaker, the size of which is set to
“Small.”
Outputs low-frequency components of the front left and right
channels.
Outputs low frequency components when the sizes of speakers
are set to “Large.”
Outputs low-frequency components of the channel of speaker,
the size of which is set to “Small.”
• When “None” is selected, the sound field programs automatically enter
the Virtual CINEMA DSP mode.
Sur.B L/R SP
Choices:
None
Front SP
Choices:
Small/Large*
Sets the sizes of front left and right speakers.
Small
Large
Select this when small speakers are
connected. Low-frequency components of the
front left and right channels are output from a
subwoofer.
Select this when large speakers are
connected.
Note
• When “LFE/Bass Out” is set to “Front,” you can only select “Large.” If
“LFE/Bass Out” is changed to “Front,” “Front SP” automatically
switches to “Large” even when it is set to “Small.”
Center SP
Choices:
None/Small*/Large
Sets the size of center speaker.
None
Small
Large
Select this when no center speaker is
connected. Center channel signals are spread
to front left and right speakers.
Select this when a small center speaker is
connected. Low-frequency components of
center channel are output from a subwoofer.
If a subwoofer is not connected they are
output from front speakers.
Select this when a large center speaker is
connected.
None/SMLx1/SMLx2*/LRGx1/LRGx2
Sets sizes of left and right surround back speakers.
SMLx1
SMLx2
LRGx1
LRGx2
Select this when no surround back speaker
are connected. Surround back channel signals
are output from the surround L/R speakers
and subwoofer. If the subwoofer is disabled,
they are output from the surround L/R
speakers and front speakers.
Select this when one small surround back
speaker is connected.
Select this when two small surround back
speakers are connected.
Select this when one large surround back
speaker is connected.
Select this when two large surround back
speakers are connected.
y
• When “None” is selected, “PLIIx Movie” or “PLIIx Music” cannot be
selected.
Crossover Freq.
Choices:
40Hz/60Hz/80Hz*/90Hz/100Hz/110Hz/120Hz/
160Hz/200Hz
Sets the lower limit of the low frequency component
output from a speaker with a size set to “Small (SMLx1/
SMLx2).” Sound with a frequency below that limit is
output from a subwoofer or front speakers.
If your subwoofer has a volume control or a crossover
frequency control, set the volume to half or the crossover
frequency at the maximum.
Subwoofer Phase
Choices:
Normal*/Reverse
Sets the phase of your subwoofer if bass sounds are
lacking or unclear.
Normal
Select this not to change the phase of your
subwoofer.
Reverse Select this to reverse the phase of your
subwoofer.
40 En
Operating various settings for this unit (Setup menu)
■
B)Level
GEQ
Adjustable range: -10.0dB to +10.0dB (0.5 dB step)
Defaults:
“FR.L/FR.R/SWFR” 0dB*
“CNTR/SUR.L/SUR.R/SBL/SBR” -1.0dB
63Hz/160Hz/400Hz/1kHz/2.5kHz/
6.3kHz/16kHz
Adjustable range: -6.0dB to 0dB* to +6.0dB (0.5 dB step)
Separately adjusts volume of each speaker so that the
sounds form speakers are at the same volume at the
listening position. Items to be displayed vary depending
on the number of speakers connected.
Adjusts sound quality of each speaker using a graphic
equalizer. The graphic equalizer of this unit can adjust
signal levels in 7 frequency ranges.
To adjust the signal level in each range, select the desired
speaker with nCursor l / h while “→” is displayed
next to “Channel,” then select the desired frequency band
with nCursor k / n, and adjust the signal level with
nCursor l / h.
■ C)Distance
Adjusts timing at which each speaker outputs sound so
that sounds from speakers reach the listening position at
the same time. Set unit (Unit) first and set the distance of
each speaker.
meters (m)/feet (ft)*
meters (m)
feet (ft)
Displays the speaker distance in meters.
Displays the speaker distance in feet.
Adjustable range: 0.30m to 24.00m (1.0ft to 80.0ft)
Defaults:
3.00m (10.0ft) “Front L/Front R/
SWFR”
2.60m (8.5ft) “Center”
2.40m (8.0ft) “Sur. L/Sur. R/
Sur.B L/Sur.B R”
y
■ D)Equalizer
Adjusts sound quality and tone using a parametric graphic
equalizer.
EQ Type Select
Choices:
Auto PEQ/GEQ*/Off
Select an equalizer type.
Not generate test tones.
Generates test tones.
Sound Setup
You can set various items for sound outputs.
■
1 Dynamic Range
Choices:
Min/Auto/STD/Max*
Selects the dynamic range adjustment method for
reproducing bitstream signals.
Min/Auto (Min) Sets the dynamic range suitable for
low volume or a quiet environment, such as
at night, for bitstream signals except for
Dolby TrueHD signals.
(Auto) Adjusts the dynamic range for Dolby
TrueHD signals based on input signal
information.
STD
Sets the standard dynamic range
recommended for regular home use.
Max
Outputs sound without adjusting the
dynamic range of the input signals.
■ 2 Lipsync
Adjusts delay between video output and audio output.
HDMI Auto
Choices:
Off*/On
Automatically adjusts output timing of audio and video
signals when a monitor that supports an automatic lipsync function is connected to this unit.
Off
41 En
English
On
Select this when the connected monitor does
not support the automatic lip-sync function or
you do not use the automatic lip-sync function.
Set the correction time in “Manual Delay.”
Select this when the connected monitor
supports the automatic lip-sync function. Fine
adjust the correction time in “Auto Delay.”
APPENDIX
Auto PEQ Uses a parametric equalizer selected in
“Auto Setup.” Characteristics of the
currently used parametric equalizer (see
page 18) are displayed below “Auto PEQ.”
GEQ
Uses a graphic equalizer. Press nENTER
to adjust the characteristics of the graphic
equalizer.
Off
Not use a graphic equalizer.
Off
On
ADDITIONAL
INFORMATION
• Different items are displayed depending on settings of “A)Config” (see
page 39).
• When only one surround back speaker is connected, “Sur.B” appears
instead of “Sur.B L” and “Sur.B R.”
Off*/On
Switches between on and off of an oscillator that generates
test tones. To turn on the oscillator, select “On” using
nCursor l / h. When “On” is selected, you can adjust
the settings of “2 Manual Setup” while listening to a test
tone.
ADVANCED
OPERATION
Front L / Front R / Center / Sur. L /
Sur. R / Sur.B L / Sur.B R / SWFR
E)Test Tone
Choices:
BASIC
OPERATION
Unit
Choices:
■
PREPARATION
• When only one surround back speaker is connected, “SB” appears
instead of “SBL” and “SBR.”
• You can adjust the volume listening to test tones when you set “Test
Tone” to “On” (see page 41).
• If your subwoofer has a volume control or a crossover frequency control,
set the volume to half or the crossover frequency at the maximum.
INTRODUCTION
y
Choices:
Operating various settings for this unit (Setup menu)
Auto Delay
■
Adjustable range: 0 to 240ms (1 ms step)
Choices:
Fine adjust the correction time when “HDMI Auto” is set
to “On.” The actual correction time is displayed under in
“Auto Delay” field and an offset time set by the user in
“Offset” field.
Upscales the resolution of HDMI output that is converted
from analog video input signals and output from the
HDMI OUT jack.
Manual Delay
• Resolution of the HDMI output converted from 720p or 1080i analog
video signals cannot be upscaled.
• When a video monitor is connected to this unit via the HDMI jack, this
unit automatically detects a resolution that the monitor supports. An
asterisk (*) appears on the left of the detected resolution.
• If this unit cannot detect the resolution that the monitor supports, set
“MON.CHK” in the advanced setup menu to “SKIP” (see page 45) and
try it again.
Adjustable range: 0* to 240ms (1 ms step)
Manually fine adjusts the correction time. Select this when
the connected monitor does not support the automatic lipsync function or you set “HDMI Auto” to “Off.”
Function Setup
You can set various items for HDMI and display.
Resolution
Through*/480p/720p/1080i/1080p
Notes
■
Aspect
Choices:
Thrgh*/16:9/Smart
You can set items for HDMI.
Set a horizontal to vertical ratio (aspect ratio) of images
reproduced by HDMI signals output from the HDMI OUT
jack when the HDMI signals are converted from analog
video input signals by a video conversion function.
■
Thrgh
1 HDMI
Standby Through
Choices:
Selects on or off of output of HDMI signals input from the
HDMI IN jack to the HDMI OUT jack when this unit is on
standby. When this parameter is set to “On” signals input
from the HDMI 1-4 jacks can be output to a monitor
component.
On
Outputs the HDMI signals to the HDMI OUT
jack.
Not output the HDMI signals to the HDMI
OUT jack.
Off
y
• To enables pass-through output, any one of the input sources connected
to the HDMI1-4 must be selected before switching to standby.
• When Standby Through turns on, the HDMI THROUGH indicator on the
front panel display lights up. While the indicator lights up, this unit
consumes up to 3W of power even on standby.
■
Audio Output
Choices:
Amp*/TV/Amp+TV
Selects this unit or a component connected to this unit via
the HDMI OUT jack of this unit for reproducing sound
signals input from the HDMI IN jack.
Amp
TV
Amp+TV
Outputs HDMI sound signals form the
speakers connected to this unit.
Outputs HDMI sound signals from the
speakers of a TV connected to this unit.
Sound output from the speakers connected to
this unit is muted.
Outputs HDMI sound signals from the
speakers connected to this unit and the
speakers of a TV connected to this unit.
Note
• Signal formats of audio and visual signals output from this unit to the
monitor vary depending on specifications of the monitor.
42 En
Outputs the video signals without changing
the aspect ratio.
Outputs the video signals that displays 4:3
images on a 16:9 monitor with black bands
on the right and left sides of the monitor
screen.
Outputs the video signals that displays 4:3
images on a 16:9 monitor by stretching right
and left of images to fit in the monitor screen.
On/Off*
16:9
Smart
Notes
• You cannot change the aspect ratio of the screen when “Resolution” is set
to “Thrgh.”
• The setting is not effective for inputs with the aspect ratio other than 4:3.
• You cannot obtain an effect of the aspect ratio when visual signals are
input from the HDMI IN jack or 720p, 1080i or 1080p signals are input.
2 Display
You can set items for a monitor or the front panel display.
■
Dimmer
Adjustable range: -4 to 0*
Sets brightness of the front panel display. As the value is
lowered, the brightness of the front panel display is
darkened.
Note
• The brightness of display does not become bright in direct mode even if
the value is increased.
■
FL Scroll
Choices:
Continue*/Once
Selects the way to scroll the screen when a total number of
characters exceed a display area of the front panel display.
Continue
Once
Repeatedly displays all characters by
scrolling.
Displays all characters by scrolling once,
halts scrolling, and then displays first 14
characters.
Operating various settings for this unit (Setup menu)
■
OSD Shift
4 Input Rename
Adjustable range: -5 to 0* to +5
3 Volume
Selecting a name to be displayed from templates
Select an input source that you want to change the name,
and select a name from the following templates using
Cursor.
You can set items for volumes.
■
Adaptive DRC
Choices:
Auto/Off*
VOLUME: low
Auto
Off
Entering an original name
Select an input source that you want to name, and press
nENTER. You can enter up to 9 characters by selecting
one character at a time with the following keys according
to the following operation.
Auto
nCursor l / h
Off
Input level
VOLUME: high
Adjusts the dynamic range automatically.
Not adjust the dynamic range automatically.
y
• The Adaptive DRC setting is effective for headphones.
Max Volume
Adjustable range: -30.0dB to +15.0dB/+16.5dB* (5.0 dB
step)
Sets the maximum volume level so that the volume will
not be accidentally increased. For example, you can adjust
the volume between –80.0 dB and –5.0 dB when you set
this parameter to “–5.0dB.” The volume increases to the
maximum level when this parameter is set to +16.5 dB
(default).
■
Init. Volume
The following characters are available for input.
A to Z, 0 to 9, a to z, symbols (#, *, –, +, etc.) and space
DSP Parameter
You can set parameters for the sound field programs. For
details, see page 36.
Memory Guard
Choices:
Off
On
Off*/Mute/-80.0dB to +16.5dB (0.5 dB step)
Sets the volume at the time this unit is turned on. When
this parameter is set to “Off,” the volume is set to a level
that last time this unit is set to standby.
Off*/On
Protects settings of setup menu against accidental
alteration.
Not protect settings.
Protects the settings of the setup menu
(except for the Memory Guard setting).
Note
• When this parameter is switched to “On,” “G” appears while the setup
menu is displayed on the video monitor.
APPENDIX
Choices:
nENTER
ADDITIONAL
INFORMATION
■
nCursor k / n
For selecting characters that you
want to change
For selecting characters to be
entered
For entering the selected characters
ADVANCED
OPERATION
Input level
Output level
Output level
Off
– Satellite
– VCR
– Tape
– MD
– PC
– iPod
– HD DVD
– “blank”
BASIC
OPERATION
If the VOLUME setting is low:
the dynamic range is narrow
If the VOLUME setting is high:
the dynamic range is wide
– Blu-ray
– DVD
– SetTopBox
– Game
– TV
– DVR
– CD
– CD-R
PREPARATION
Adjust the dynamic range in conjunction with the volume
level. This feature is useful when you are listening at
lower volumes or at night. When this function is enabled,
the dynamic range is adjusted as follows.
Auto
Changes input source names to be displayed on the front
panel display.
You can select an input source that you want to change the
name to be displayed using nCursor.
INTRODUCTION
Adjusts top and bottom positions of the screen displayed
on the video monitor. To move up the screen, set this value
larger. To move down the screen, set it smaller.
Note
• When you set “Max Volume” and “Init. Volume,” the setting of “Max
Volume” becomes effective. For example, when you set “Max Volume”
to “–30.0dB” and “Init. Volume” to “0.0dB,” the volume is
automatically set to “–30.0dB” at the next time this unit is turned on.
English
43 En
Controlling other components with the remote control
You can control external components for a selected input source with the remote control. The keys available for
controlling external components are as follows:
dSOURCE POWER
Turns on and off an external component.
Input source
nCursor, ENTER, RETURN
Operates the menus of external components.
pDISPLAY
Switches between the screens of external components.
rExternal component operation keys
Function as a recording or playback key of an external
component, or a menu display key.
sNumeric keys
Function as numeric keys of an external component.
tTV control keys
INPUT
MUTE
TV VOL +/–
TV CH +/–
POWER
Switches visual inputs of TV
Mute audio of TV
Controls the volume of TV
Switches channels of TV
Turns on and off TV
The following remote control codes are assigned to input
sources as factory default settings. For a complete list of
available remote control codes, refer to “List of remote
control codes” at the end of this manual.
■
Default remote control code settings
Input source
Category
Manufacturer
Default
code
[HDMI1]
Blu-ray Disc
Yamaha
2018
[HDMI2]
—
—
—
[HDMI3]
—
—
—
[HDMI4]
—
—
—
[AV1]
—
—
—
[AV2]
—
—
—
[AV3]
CD
Yamaha
5013
[AV4]
—
—
—
[AV5]
—
—
—
[AV6]
—
—
—
[AUDIO1]
—
—
—
[AUDIO2]
—
—
—
[V-AUX]
—
—
—
[TUNER]
Tuner
Yamaha
5007
44 En
Manufacturer
Default
code
[DOCK]
DOCK
Yamaha
5011
[A]/[B]
—
—
—
“—” indicates no assignment
y
• An external component that is controlled by the remote control can be
automatically selected according to selection of the scenes (see page 21).
Setting remote control codes
You can control other components by setting the
appropriate remote control codes. For a complete list of
available remote control codes, refer to “List of remote
control codes” at the end of this manual.
1
Press cCODE SET on the remote control
using a pointed object such as the tip of a
ballpoint pen.
bTRANSMIT on the remote control blinks twice.
2
Press gInput selection keys.
3
Enter a remote control code using
sNumeric keys.
Once the remote control code is registered,
bTRANSMIT on the remote control blinks twice.
If it fails, bTRANSMIT blinks six times. Repeat
from step 1.
y
• You can use tTV control keys only for controls of TV regardless
of selected input sources.
• You need to set the remote control code first to control external
components.
• The remote control keys for controlling external components are
available only when the external components have corresponding control
keys.
Category
Resetting all remote control codes
You can clear all the remote control codes previously set,
and reset all of them to the initial factory settings.
1
Press cCODE SET on the remote control
using a pointed object such as a tip of a
ballpoint pen.
bTRANSMIT on the remote control blinks twice.
2
Press lSETUP on the remote control.
3
Enter “9981” using sNumeric keys.
Once the initialization is complete, bTRANSMIT
on the remote control blinks twice. If it fails,
bTRANSMIT blinks six times. Repeat from
step 1.
Advanced setup
Set this unit to the standby mode.
2
Press ASTANDBY/ON while pressing and
holding LSTRAIGHT on the front panel.
The advanced setup menu appears on the front panel
display.
ADVANCEDSETUP
3
y
• Set values are placed in XXX of the following parameters on an
actual display screen.
SP IMP. -XXX
Choices:
6 MIN/8 MIN*
Selects output impedance of this unit according to
connected speakers.
5
Press ASTANDBY/ON, turns off this
system, and press ASTANDBY/ON again.
The value set in step 3 becomes effective, and this
unit turns on. When you select initialization in step 3,
the initialization is performed.
Setting a remote control ID
Two IDs are provided for the remote control of this unit. If
another Yamaha amplifier is in the same room, setting a
different remote control ID to this unit prevents unwanted
operation of the other amplifier.
ID1 is set for both remote control and amplifier by default.
When you change the remote control ID, display
“Advance Setup” (see the previous section) and change the
ID for the amplifier too.
2
Press lSETUP on the remote control.
3
Enter the desired remote control ID code.
To switch to ID1:
Enter “5019” using sNumeric keys.
To switch to ID2:
Enter “5020” using sNumeric keys.
Once the remote control code is registered,
bTRANSMIT blinks twice.
If it fails, bTRANSMIT blinks six times. Repeat
from step 1.
REMOTE ID -XXX
Choices:
ID1*/ID2
Sets a remote control ID. When using multiple
Yamaha AV receivers, you can operate them with a
single remote control by setting the receiver IDs to
the same setting.
BI AMP - XXX
Choices:
ON/OFF*
Switches on and off of bi-amp connection of main
speakers. For bi-amp connection, see page 12.
MON.CHK - XXXX
Choices:
YES*/SKIP
Adds upscaling limitation on output signals to a video
monitor connected to this unit via the HDMI OUT
jack.
y
• Initializing the remote control code (see page 44) returns it to ID1.
APPENDIX
INIT-XXXXXXXXX
Choices:
ADDITIONAL
INFORMATION
Press cCODE SET on the remote control
using a pointed object such as the tip of a
ballpoint pen.
bTRANSMIT blinks twice.
ADVANCED
OPERATION
1
BASIC
OPERATION
Press KPROGRAM l / h repeatedly to
select the parameter you want to change.
The default setting are marked with “*.”
Press LSTRAIGHT a few times to select the
value you want to change.
The value selected here becomes effective when this
unit is turned on the next time. You can change
multiple settings by repeating steps 3 and 4.
PREPARATION
1
4
INTRODUCTION
In the advanced setup, you can set basic operations of this
unit, such as on and off of a bi-amp connection, or
initialize user settings. Perform the following steps to
change settings.
DSP PARAM/VIDEO/ALL/CANCEL
Initializes various settings stored in this unit. You can
select an initialization method from the following.
English
DSP PARAM: All parameters of sound field
programs
VIDEO:
Video conversion settings (resolution/
aspect) in the setup menu and the OSD
display position
ALL:
Reset this unit to initial factory
settings
CANCEL:
Cancellation of initialization
45 En
APPENDIX
Troubleshooting
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
General
Problem
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
Cause
Remedy
See
page
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable properly to an AC wall
outlet.
—
The speaker impedance setting is
incorrect.
Set the speaker impedance to match your speakers.
45
(When this unit is turned back on and
“CHECK SP WIRES!” is displayed.) The
protection circuitry has been activated
because this unit was turned on while a
speaker cable was shorted.
Make sure that all speaker cables between this unit
and speakers are connected properly.
11
This unit cannot be
turned off.
The internal microcomputer is frozen due
to an external electric shock (such as
lightning or excessive static electricity) or
by a drop in power supply voltage.
Disconnect the power cable from the AC wall outlet,
wait about 30 seconds and then plug it in again.
—
No sound.
“Audio Output” in “1 HDMI” of Function
Setup is set to “TV.”
Select a choice for “Audio Output” (Function
Setup→1 HDMI→Audio Output) other than “TV.”
42
A proper audio decoder is not selected.
Display the OPTION menu and set “Decoder Mode”
to “Auto.”
33
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
14-16
No appropriate input source has been
selected.
Select an appropriate input source with NINPUT l
/ h or the gInput selection keys on the
remote control.
21
Speaker connections are not secure.
Secure the connections.
11
The volume is turned down or muted.
Turn up the volume.
—
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
Display Signal info of the option menu and check the
input signal format.
If “No Signal” is displayed, check if the playback
component is properly connected to this unit (or a
proper input source is selected).
If “___” is displayed, the input signal in that format
cannot be reproduced by this unit.
—
The HDMI components connected to this
unit do not support the HDCP copy
protection standards.
Connect HDMI components that support the HDCP
copy protection standards.
55
46 En
Troubleshooting
Problem
No picture.
Cause
Remedy
See
page
14
This unit outputs the video signals are not
supported on the video monitor connected
to the HDMI OUT jack.
Displays the advanced setup menu and select
“VIDEO” in “INIT” to reset the video parameters.
45
Displays the advanced setup menu and set
“MON.CHK” to “YES.”
45
Non-standard video signals are input.
Connect the monitor to this unit via the
COMPONENT OUT jacks or the composite output
terminals.
14
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker impedance setting is correct.
45
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned off this unit.
Turn on this unit, and play the source again.
—
Sound is heard from
the speaker on one
side only.
The playback component or speakers are
not connected properly.
Connect the cables properly. If the problem persists,
the cables may be defective.
11
The speaker level settings are incorrect.
Adjust “B)Level” settings.
41
Only the center
speaker outputs
substantial sound.
When a monaural source sound field
program is applied, sound of all channels
are output from the center speaker for
some surround decoders.
Try another sound field program.
24
No sound is output
from a specific
speaker.
Output from that speaker is disabled.
Check the Speaker indicators on the front panel
display. If the corresponding indicator is turned off,
try the following.
1) Change the input source to another one.
2) With the selected sound field program, sound is not
output from that speaker. Select another sound field
program.
3) “None” may have been selected for that speaker on
this unit. Display Speaker Setup in the Setup menu
and enables output of that speaker.
6, 21, 24,
40
The volume of that speaker is set to
minimum in Speaker Setup in the Setup
menu.
Display Speaker Setup in the Setup menu and adjust
the volume (Manual Setup→B)Level).
41
This unit or speaker is malfunction.
Check the Speaker indicators on the front panel
display. If the corresponding indicator lights up,
connect another speaker and check if sound is output.
If sound is not output, this unit may be malfunction.
6, 10
This unit is in the “STRAIGHT” mode
and a monaural source is being played
back.
Press LSTRAIGHT or the jSTRAIGHT on the
remote control to turn off the “STRAIGHT” mode.
27
Sound may not be output from certain
channels depending on input sources or
sound field programs.
Try another sound field program.
24
The sound suddenly
goes off.
No sound is heard
from the surround
speakers.
APPENDIX
If your monitor does not support the HDMI
connection, connect it to the COMPONENT OUT
jacks or the composite output terminals and select an
appropriate video input on the monitor.
ADVANCED
OPERATION
The composite output terminals are used
to output a component video signal, or the
COMPONENT VIDEO jacks are used to
output a composite video signal.
BASIC
OPERATION
—
PREPARATION
Select an appropriate video input on the monitor.
INTRODUCTION
An appropriate video input is not selected
on the monitor.
English
47 En
Troubleshooting
Problem
No sound is heard
from the subwoofer.
Cause
Remedy
See
page
“LFE/Bass Out” of “A)Config” in
“Speaker Setup” of the setup menu
(Speaker Setup→Manual
Setup→A)Config) is set to “Front” when
a Dolby Digital, DTS or AAC signal is
being played.
Set “LFE/Bass Out” to “SWFR” or “Both.”
39
“LFE/Bass Out” of “A)Config” in
“Speaker Setup” of the setup menu
(Speaker Setup→Manual
Setup→A)Config) is set to “SWFR” or
“Front” when a 2-channel source is being
played.
Set “LFE/Bass Out” to “Both.”
39
The source does not contain low
frequency signals.
No sound is heard
from the surround
back speakers.
“Extended Surround” in the OPTION
menu is set to “Off,” or an input signal
does not contain a surround back flag with
“Extended Surround” set to “Auto.”
Set “Extended Surround” other than “Off” or “Auto.”
40
The audio input
sources cannot be
played in the desired
digital audio signal
format.
The connected component is not set to
output the desired digital audio signals.
Set the playback component properly referring to its
operating instructions.
—
Noise/hum noise is
heard.
Incorrect cable connection.
Connect the audio cables properly. If the problem
persists, the cables may be defective.
—
A DTS-CD is being played back.
1) When only noise is output
If a DTS bitstream signal is not properly input to this
unit, only noise is output. Connect the playback
component to this unit by digital connection and play
back the DTS-CD. If the condition is not improved,
the problem may results from the playback
component. Consult the manufacturer of the playback
component.
2) When noise is output during playback or skip
operation
Before playing back the DTS-CD, display the option
menu after selecting the input source and set
“Decoder Mode” to “DTS.”
“Memory Guard!” is
displayed and the
setting cannot be
changed.
“Memory Guard” in “Set Menu” is set to
“On.”
Set “Memory Guard” to “Off.”
43
This unit does not
operate properly.
The internal microcomputer is frozen due
to an external electric shock (such as
lightning or excessive static electricity) or
by a drop in power supply voltage.
Disconnect the power cable from the AC wall outlet,
wait about 30 seconds and then plug it in again.
—
“CHECK SP WIRES!”
appears on the front
panel display.
Speaker cables are short-circuited.
Make sure all speaker cables are connected correctly.
12
There is noise
interference from
digital or radio
frequency equipment.
This unit is too close to other digital or
radio frequency equipment.
Move this unit further away from such equipment.
—
48 En
16, 34
Troubleshooting
Problem
Cause
Remedy
This unit suddenly
enters the standby
mode.
The internal temperature becomes too
high and the overheat protection circuitry
has been activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
Cause
Remedy
—
HDMI
Problem
No picture or sound.
See
page
The number of the connected HDMI
components is over the limit.
Disconnect some of the HDMI components.
—
The connected HDMI component does not
support high-bandwidth digital copyright
protection (HDCP).
Connect an HDMI component that supports HDCP.
15
Problem
FM stereo reception is
noisy.
See
page
Check the antenna connections.
17
Replace the outdoor antenna with a more
sensitive multi-element antenna.
—
Switch to monaural mode.
34
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multi-path interference.
Adjust the antenna height or orientation, or
place it in a different location.
—
The desired station
cannot be tuned into
with the automatic
tuning method.
You are in an area far from a station or
an input from the antenna is weak.
Replace an outdoor antenna with more
sensitive multi element antenna.
—
Tune in manually or by direct frequency
tuning.
28
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is weak or the antenna
connections are loose.
Adjust the AM loop antenna orientation.
17
Use the manual tuning method.
28
There are continuous
crackling and hissing
noises.
Supplied AM loop antenna is not
connected.
Connect the AM loop antenna correctly even
if you use an outdoor antenna.
17
The noises may be caused by lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
It is difficult to completely eliminate noise,
but it can be reduced by installing and
properly grounding an outdoor AM antenna.
17
A TV set is being used nearby.
Move this unit away from the TV set.
—
There are buzzing and
whining noises.
APPENDIX
AM
You are too far from the station
transmitter or the input from the
antenna is weak.
Remedy
ADVANCED
OPERATION
FM
Cause
BASIC
OPERATION
Tuner (FM/AM)
PREPARATION
The video software is copy-protected.
INTRODUCTION
The picture is
disturbed.
See
page
English
49 En
Troubleshooting
Remote control
Problem
The remote control
does not work or
function properly.
Cause
Remedy
See
page
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees
offaxis from the front panel.
9
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, strobe
light, etc.) is striking the remote control
sensor of this unit.
Adjust the lighting angle or reposition this unit.
—
The batteries are weak.
Replace all batteries.
9
The remote control ID of the remote
control and this unit do not match.
Match the remote control ID of this unit and the
remote control.
45
The remote control code is not correctly
set.
Set the remote control code correctly using “List of
remote control codes” at the end of this manual.
44
Try setting another code of the same manufacturer
using “List of remote control codes” at the end of this
manual.
44
If this unit does not work when you press nCursor,
do the following.
When the key does not work during DVD disc menu
operation: press the gInput selection keys on
the remote control again.
When the key does not work during OPTION menu/
SETUP menu operation: press the key applicable for
the current menu operation again.
—
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
iPod™
Note
• In case of a transmission error without a status message appearing on the front panel display and the OSD, check the connection of your iPod (see
page 16).
Problem
Loading...
Cause
Remedy
See
page
This unit is in the middle of recognizing
the connection with your iPod.
This unit is in the middle of acquiring
song lists from your iPod.
Connect error
There is a problem with the signal path
from your iPod to this unit.
Unknown iPod
The iPod being used is not supported by
this unit.
iPod Connected
Your iPod is properly placed in the
Yamaha iPod universal dock.
50 En
Turn off this unit and reconnect the Yamaha iPod
universal dock to the DOCK terminal of this unit.
16
Remove your iPod in the Yamaha iPod universal dock
and then place it back in the dock.
16
This unit supports iPod Touch, iPod (Click Wheel),
iPod nano and iPod mini.
—
Troubleshooting
Problem
Cause
Remedy
See
page
Your iPod is removed from the Yamaha
iPod universal dock.
Place your iPod in the Yamaha iPod universal dock.
16
Unable to play
This unit cannot play back the songs
currently stored on your iPod.
Check that the songs currently stored on your iPod
are playable.
—
Store some other playable music files on your iPod.
—
Bluetooth™
Searching...
Cause
Remedy
See
page
The Bluetooth wireless audio receiver and
the Bluetooth component are in the
middle of the pairing.
The pairing is completed.
Canceled
The pairing is canceled.
BT Connected
The connection between the Yamaha
Bluetooth wireless audio receiver and the
Bluetooth component is established.
BT Disconnected
The Bluetooth component is disconnected
from the Yamaha Bluetooth wireless
audio receiver.
ADVANCED
OPERATION
Completed
BASIC
OPERATION
The Bluetooth wireless audio receiver and
the Bluetooth component are in the
middle of establishing the connection.
PREPARATION
Problem
INTRODUCTION
Disconnected
Auto Setup (YPAO)
Notes
If the “ERROR” or “WARNING” screen appears, resolve the problem and then run “Auto Setup” again.
Warning message “W-2” or “W-3” indicates that the adjusted settings may not be optimal.
Depending on the speakers, warning message “W-1” may appears even if the speaker connections are correct.
If error message “E-10” occurs repeatedly, contact a qualified Yamaha service center.
APPENDIX
•
•
•
•
Before Auto Setup
Error message
Cause
Remedy
See
page
Connect MIC!
Optimizer microphone is not connected.
Connect the supplied optimizer microphone to the
OPTIMIZER MIC jack on the front panel.
18
Unplug HP!
Headphones are connected.
Unplug the headphones.
—
Memory Guard!
The parameters of this unit are protected.
Set “Memory Guard” to “Off.”
43
During Auto Setup
Error message
Cause
Remedy
See
page
Front L/R channel signals are not
detected.
Check the front L/R speaker connections.
11
E-2:NO SUR. SP
Only a signal from one of the surround
channels are detected.
Check the surround L/R speaker connections.
11
51 En
English
E-1:NO FRONT SP
Troubleshooting
Error message
Cause
Remedy
See
page
E-4:SBR->SBL
Only right surround back channel signal
is detected.
If you connect only one surround back speaker,
connect it to the L-side (SINGLE) terminal.
11
E-5:NOISY
Measurement cannot be performed
accurately due to loud ambient noise.
Try running “Auto Setup” in a quiet environment.
—
Turn off noisy electric equipment like air
conditioners or move them away from the optimizer
microphone.
—
E-6:CHECK SUR.
Surround back speakers are connected,
though surround L/R speakers are not.
When using surround back speakers, you need to
connect surround L/R speakers.
11
E-7:NO MIC
The optimizer microphone was
unplugged during the “Auto Setup”
procedure.
Do not touch the optimizer microphone during “Auto
Setup.”
18
E-8:NO SIGNAL
The optimizer microphone does not
detect test tones.
Check whether the microphone is properly placed.
18
Check whether the speakers are properly placed and
connected.
11
The optimizer microphone or OPTIMIZER MIC
jack may be defective. Contact the nearest Yamaha
dealer or service center.
18
E-9:USER CANCEL
“Auto Setup” was cancelled due to an
inappropriate user operation.
Run “Auto Setup” again.
18
E-10:INTERNAL ERROR
An internal error occurred.
Run “Auto Setup” again.
18
After Auto Setup
Error message
Cause
Remedy
See
page
W-1:OUT OF PHASE
Speaker polarity is not correct. This
message may appear depending on the
speakers even when the speakers are
connected correctly.
Check the polarities (+, –) of the displayed speaker.
If they are correct, the speakers work properly even
when this message is displayed.
11
W-2:OVER 24m (80ft)
The distance between the speaker and the
listening position is over 24 m (80 ft).
Bring the speaker within 24 m (80 ft.) area around
the listening position.
—
W-3:LEVEL ERROR
The difference of volume level among
speakers is excessive.
Recheck the speaker positions and make sure all
speakers are placed in a similar environment.
—
Check the polarities (+, –) of the speakers.
11
We recommended that you use speakers with the
same or similar specifications.
—
Adjust the output volume of the subwoofer.
—
52 En
Glossary
■
Audio and video synchronization (lip sync)
■
Dolby Digital Surround EX
Dolby Digital EX creates 6 full-bandwidth output channels from 5.1channel sources.
For the best results, Dolby Digital EX should be used with movie
sound tracks recorded with Dolby Digital Surround EX. With this
additional channel, you can experience more dynamic and realistic
moving sound especially with scenes with “fly-over” and “flyaround” effects.
■
■
Bi-amplification connection
■
Component video signal
■
Composite video signal
■
Deep Color
■
Dolby Digital
Dolby Digital is a digital surround sound system that gives you
completely independent multi-channel audio. With 3 front channels
(front L/R and center), and 2 surround stereo channels, Dolby Digital
provides 5 full-range audio channels. With an additional channel
especially for bass effects, called LFE (Low Frequency Effect), the
system has a total of 5.1-channels (LFE is counted as 0.1 channel). By
using 2-channel stereo for the surround speakers, more accurate
moving sound effects and surround sound environment are possible
than with Dolby Surround. The wide dynamic range from maximum
to minimum volume reproduced by the 5 full-range channels and the
precise sound orientation generated using digital sound processing
provide listeners with unprecedented excitement and realism.
With this unit, any sound environment from monaural up to a 5.1channel configuration can be freely selected for your enjoyment.
■
Dolby Pro Logic IIx
Dolby Pro Logic IIx is a new technology enabling discrete
multichannel playback from 2-channel or multi-channel sources.
There are three modes available: “Music mode” for music sources,
“Movie mode” for movie sources (for 2-channel sources only) and
“Game mode” for game sources.
■
Dolby Surround
Dolby Surround is widely used with nearly all video tapes and laser
discs, and in many TV and cable broadcasts as well. Dolby Surround
uses a 4-channel analog recording system to reproduce realistic and
dynamic sound effects: 2 front left and right channels (stereo), a
center channel for dialog (monaural), and a surround channel for
special sound effects (monaural). The surround channel reproduces
sound within a narrow frequency range. The Dolby Pro Logic decoder
built into this unit employs a digital signal processing system that
automatically stabilizes the volume on each channel to enhance
moving sound effects and directionality.
■
APPENDIX
Deep Color refers to the use of various color depths in displays, up
from the 24-bit depths in previous versions of the HDMI specification.
This extra bit depth allows HDTVs and other displays go from
millions of colors to billions of colors and eliminate on-screen color
banding for smooth tonal transitions and subtle gradations between
colors. The increased contrast ratio can represent many times more
shades of gray between black and white. Also Deep Color increases
the number of available colors within the boundaries defined by the
RGB or YCbCr color space.
Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to decode vast
numbers of existing Dolby Surround sources. This new technology
enables a discrete 5-channel playback with 2 front left and right
channels, 1 center channel, and 2 surround left and right channels
instead of only 1 surround channel for conventional Pro Logic
technology. There are three modes available: “Music mode” for music
sources, “Movie mode” for movie sources and “Game mode” for
game sources.
ADVANCED
OPERATION
With the composite video signal system, the video signal is composed
of three basic elements of a video picture: color, brightness and
synchronization data. A composite video jack on a video component
transmits these three elements combined.
■
BASIC
OPERATION
With the component video signal system, the video signal is separated
into the Y signal for the luminance and the PB and PR signals for the
chrominance. Color can be reproduced more faithfully with this
system because each of these signals is independent. The component
signal is also called the “color difference signal” because the
luminance signal is subtracted from the color signal. A monitor with
component input jacks is required in order to output component
signals.
Dolby Digital Plus
Dolby Digital Plus is an advanced audio technology developed for
high-definition programming and media including HD broadcasts,
and Blu-ray Disc. Selected as an optional audio standard for Blu-ray
Disc, this technology delivers multichannel sound with discrete
channel output. Supporting bitrates up to 6.0 Mbps, Dolby Digital
Plus can carry up to 7.1 discreet audio channels simultaneously.
Supported by HDMI version 1.3 and designed for the optical disc
players and AV receivers/amplifiers of the future, Dolby Digital Plus
also remains fully compatible with the existing multichannel audio
systems that incorporate Dolby Digital.
PREPARATION
A bi-amplification connection uses two amplifiers for a speaker.
One amplifier is connected to the woofer section of a loudspeaker
while the other is connected to the combined mid and tweeter section.
With this arrangement each amplifier operates over a restricted
frequency range. This restricted range presents each amplifier with a
much simpler job and each amplifier is less likely to influence the
sound in some way.
INTRODUCTION
Lip sync, an abbreviation for lip synchronization, is a technical term
that involves both a problem and a capability of maintaining audio and
video signals synchronized during post-production and transmission.
Whereas the audio and video latency requires complex end-user
adjustments, HDMI version 1.3 incorporates an automatic audio and
video syncing capability that allows devices to perform this
synchronization automatically and accurately without user interaction.
Dolby TrueHD
53 En
English
Dolby TrueHD is an advanced lossless audio technology developed
for high-definition disc-based media including Blu-ray Disc. Selected
as an optional audio standard for Blu-ray Disc, this technology
delivers sound that is bit-for-bit identical to the studio master, offering
a high-definition home theater experience.
Supporting bitrates up to 18.0 Mbps, Dolby TrueHD can carry up to 8
discrete channels of 24-bit/96 kHz audio simultaneously.
Dolby TrueHD also remains fully compatible with the existing
multichannel audio systems and retains the metadata capability of
Dolby Digital, allowing dialog normalization and dynamic range
control.
Glossary
■
DSD
Direct Stream Digital (DSD) technology stores audio signals on
digital storage media, such as Super Audio CDs. Using DSD, signals
are stored as single bit values at a high-frequency sampling rate of
2.8224 MHz, while noise shaping and oversampling are used to
reduce distortion, a common occurrence with very high quantization
of audio signals. Due to the high sampling rate, better audio quality
can be achieved than that offered by the PCM format used for normal
audio CDs. The frequency is equal to or higher than 100 kHz and the
dynamic range is 120 dB. This unit can transmit or receive DSD
signals via the HDMI jack.
■
DTS 96/24
DTS 96/24 offers an unprecedented level of audio quality for multichannel sound on DVD video, and is fully backward-compatible with
all DTS decoders. “96” refers to a 96 kHz sampling rate compared to
the typical 48 kHz sampling rate. “24” refers to 24-bit word length.
DTS 96/24 offers sound quality transparent to the original 96/24
master, and 96/24 5.1-channel sound with full-quality full-motion
video for music programs and motion picture soundtracks on DVD
video.
■
DTS Digital Surround
DTS digital surround was developed to replace the analog soundtracks
of movies with a 5.1-channel digital sound track, and is now rapidly
gaining popularity in movie theaters around the world. DTS, Inc. has
developed a home theater system so that you can enjoy the depth of
sound and natural spatial representation of DTS digital surround in
your home. This system produces practically distortion-free 6-channel
sound (technically, front left and right, center, surround left and right,
and LFE 0.1 (subwoofer) channels for a total of 5.1 channels). This
unit incorporates a DTS-ES decoder that enables 6.1-channel
reproduction by adding the surround back channel to the existing 5.1channel format.
■
DTS Express
This is an audio format for next-generation optical discs such as Bluray discs. It uses optimized low bit rate signals for network streaming.
In the case of a Blu-ray disc, this format is used with secondary audio,
enabling you to enjoy the commentary of the movie producer via the
Internet while playing the main program.
■
DTS-HD High Resolution Audio
DTS-HD High Resolution Audio is a high resolution audio
technology developed for high-definition disc-based media including
Blu-ray Disc. Selected as an optional audio standard for Blu-ray Disc,
this technology delivers sound that is virtually indistinguishable from
the original, offering a high-definition home theater experience.
Supporting bitrates up to 6.0 Mbps for Blu-ray Disc, DTS-HD High
Resolution Audio can carry up to 7.1 discrete channels of 24-bit/96
kHz audio simultaneously.
DTS-HD High Resolution Audio also remains fully compatible with
the existing multichannel audio systems that incorporate DTS Digital
Surround.
■
DTS-HD Master Audio
DTS-HD Master Audio is an advanced lossless audio technology
developed for high-definition disc-based media including Blu-ray
Disc. Selected as an optional audio standard for Blu-ray Disc, this
technology delivers sound that is bit-for-bit identical to the studio
master, offering a high-definition home theater experience.
Supporting bitrates up to 24.5 Mbps for Blu-ray Disc, DTS-HD
Master Audio can carry up to 7.1 discrete channels of 24-bit/96 kHz
audio simultaneously. Supported by HDMI version 1.3 and designed
for the optical disc players and AV receivers/amplifiers of the future,
DTS-HD Master Audio also remains fully compatible with the
existing multichannel audio systems that incorporate DTS Digital
Surround.
54 En
■
HDMI
HDMI (High-Definition Multimedia Interface) is the first industrysupported, uncompressed, all-digital audio/video interface. Providing
an interface between any source (such as a set-top box or AV receiver)
and an audio/video monitor (such as a digital television), HDMI
supports standard, enhanced or high-definition video as well as multichannel digital audio using a single cable. HDMI transmits all ATSC
HDTV standards and supports 8-channel digital audio, with
bandwidth to spare to accommodate future enhancements and
requirements.
When used in combination with HDCP (High-bandwidth Digital
Content Protection), HDMI provides a secure audio/video interface
that meets the security requirements of content providers and system
operators. For further information on HDMI, visit the HDMI website
at “http://www.hdmi.org/.”
■
LFE 0.1 channel
This channel reproduces low-frequency signals. The frequency range
of this channel is from 20 Hz to 120 Hz. This channel is counted as
0.1 because it only enforces a low-frequency range compared to the
full-range reproduced by the other 5/6 channels in Dolby Digital or
DTS 5.1/6.1-channel systems.
■
Neo:6
Neo:6 decodes the conventional 2-channel sources for 6- channel
playback by the specific decoder. It enables playback with the fullrange channels with higher separation just like digital discrete signal
playback. There are two modes available: “Music mode” for music
sources and “Cinema mode” for movie sources.
■
PCM (Linear PCM)
Linear PCM is a signal format under which an analog audio signal is
digitized, recorded and transmitted without using any compression.
This is used as a method of recording CDs and DVD audio. The PCM
system uses a technique for sampling the size of the analog signal per
very small unit of time. Standing for “Pulse Code Modulation,” the
analog signal is encoded as pulses and then modulated for recording.
■
Sampling frequency and number of
quantized bits
When digitizing an analog audio signal, the number of times the
signal is sampled per second is called the sampling frequency, while
the degree of fineness when converting the sound level into a numeric
value is called the number of quantized bits. The range of rates that
can be played back is determined based on the sampling rate, while
the dynamic range representing the sound level difference is
determined by the number of quantized bits. In principle, the higher
the sampling frequency, the wider the range of frequencies that can be
played back, and the higher the number of quantized bits, the more
finely the sound level can be reproduced.
■
“x.v.Color”
A color space standard supported by HDMI version 1.3. It is a more
extensive color space than sRGB, and allows the expression of colors
that could not be expressed before. While remaining compatible with
the color gamut of sRGB standards, “x.v.Color” expands the color
space and can thus produce more vivid, natural images. It is
particularly effective for still pictures and computer graphics.
Sound field program information
■
■
CINEMA DSP
SILENT CINEMA
Yamaha has developed a natural, realistic sound effect DSP algorithm
for headphones. Parameters for headphones have been set for each
sound field so that accurate representations of all the sound field
programs can be enjoyed on headphones.
■
Compressed Music Enhancer
The Compressed Music Enhancer feature of this unit enhances your
listening experience by regenerating the missing harmonics in a
compression artifact. As a result, flattened complexity due to the loss
of high-frequency fidelity as well as lack of bass due to the loss of
low-frequency bass is compensated, providing improved performance
of the overall sound system.
■
BASIC
OPERATION
Information on HDMI™
HDMI signal compatibility
Audio signals
Audio signal types
Audio signal formats
Compatible media
2ch, 32-192 kHz, 16/20/24 bit
CD, DVD-Video, DVD-Audio, etc.
Multi-ch Linear PCM
8ch, 32-192 kHz, 16/20/24 bit
DVD-Audio, Blu-ray Disc, HD DVD, etc.
DSD
2/5.1ch, 2.8224 MHz, 1 bit
SA-CD, etc.
Bitstream
Dolby Digital, DTS
DVD-Video, etc.
Bitstream (High definition audio)
Dolby TrueHD, Dolby Digital Plus, DTS-HD
Master Audio, DTS-HD High Resolution Audio,
DTS Express
Blu-ray Disc, HD DVD, etc.
ADVANCED
OPERATION
2ch Linear PCM
PREPARATION
■
Virtual CINEMA DSP
Yamaha has developed a Virtual CINEMA DSP algorithm that allows
you to enjoy DSP sound field surround effects even without any
surround speakers by using virtual surround speakers. It is even
possible to enjoy Virtual CINEMA DSP using a minimal two-speaker
system that does not include a center speaker.
INTRODUCTION
Since the Dolby Surround and DTS systems were originally designed
for use in movie theaters, their effect is best felt in a theater having
many speakers designed for acoustic effects. Since home conditions,
such as room size, wall material, number of speakers, and so on, can
differ so widely, it is inevitable that there are differences in the sound
heard.
Based on a wealth of actually measured data, Yamaha CINEMA DSP
provides the audiovisual experience of a movie theater in the listening
room of your own home by using the Yamaha original sound field
technology combined with various digital audio systems.
• If the input source component can decode the bitstream audio signals of audio commentaries, you can play back the audio sources with the audio
commentaries mixed down by using the DIGITAL INPUT OPTICAL (or COAXIAL) connections.
• Refer to the supplied instruction manuals of the input source component, and set the component appropriately.
Notes
• When CPPM copy-protected DVD-Audio is played back, video and audio signals may not be output depending on the type of the DVD player.
• This unit is not compatible with HDCP-incompatible HDMI or DVI components.
• To decode audio bitstream signals on this unit, set the input source component appropriately so that the component outputs the bitstream audio signals
directly (does not decode the bitstream signals on the component). Refer to the supplied instruction manuals for details.
• This unit is not compatible with the audio commentary features (for example, the special audio contents downloaded via Internet) of Blu-ray Disc or HD
DVD. This unit does not play back the audio commentaries of the Blu-ray Disc or HD DVD contents.
APPENDIX
y
Video signals
This unit is compatible with the video signals of the following resolutions:
• 480i/60 Hz
• 576i/50 Hz
• 480p/60 Hz
• 576p/50 Hz
• 720p/60 Hz, 50 Hz
• 1080i/60 Hz, 50 Hz
• 1080p/60 Hz, 50 Hz, 24 Hz
English
55 En
Specifications
AUDIO SECTION
• Minimum RMS Output Power for Front, Center, Surround,
Surround back
[U.S.A. and Canada models]
1 kHz, 0.9% THD, 8 Ω .......................................................... 90 W
[Other models]
1 kHz, 0.9% THD, 6 Ω .......................................................... 90 W
• Dynamic Power (IHF)
[U.S.A. and Canada models]
Front Speakers 8/6/4/2 Ω .................................. 95/110/130/150 W
[Other models]
Front Speakers 6/4/2 Ω .......................................... 100/110/125 W
• Maximum Useful Output Power (JEITA) [China, Korea, General
and Asia models]
1 kHz, 10% THD, 6 Ω ......................................................... 115 W
• Maximum Output Power [U.K., Europe, Russia and Asia models]
1 kHz, 0.7% THD, 4 Ω ........................................................ 105 W
• Dynamic Headroom [U.S.A. and Canada models]
8 Ω.......................................................................................0.23 dB
• IEC Output Power [U.K., Europe, Russia and Asia models]
Front Speakers 1 kHz, 0.9% THD, 8 Ω ................................. 90 W
• Input Sensitivity/Input Impedance
AV5, etc................................................................... 200 mV/47 kΩ
• Maximum Input Voltage
AV5, etc. (1 kHz, 0.5% THD) ...................................2.0 V or more
• Rated Output Voltage/Output Impedance
AUDIO OUT.......................................................... 200 mV/1.2 kΩ
SUBWOOFER (2ch Stereo & Front: Small)
................................................................................. 1.0 V/1.2 kΩ
• Headphone Jack Rated Output/Impedance
AV5, etc. (1 kHz, 50 mV, 8 Ω) ................................ 100 mV/470 Ω
• Frequency Response
AV5 to FRONT ..................................10 Hz to 100 kHz, +0/–3 dB
• Total Harmonic Distortion
AV5, etc. to FRONT, Pure Direct
[U.S.A. and Canada models]
(1 kHz, 50 W, 8 Ω)..................................................0.06% or less
[Other models]
(1 kHz, 50 W, 6 Ω)..................................................0.06% or less
• Signal to Noise Ratio (IHF-A Network)
AV5, etc. Input Shorted (250 mV to Front Speakers)
............................................................................. 100 dB or more
• Residual Noise (IHF-A Network)
Front Speakers.......................................................... 150 µV or less
• Channel Separation (1 kHz/10 kHz)
AV5, etc. (5.1 kΩ shorted) ............................ 60 dB/45 dB or more
• Volume Control ................................... MUTE / –80 dB to +16.5 dB
• Tone Control (Front Speakers)
BASS Boost/Cut....................................................±10 dB at 50 Hz
BASS Turnover Frequency ..................................................350 Hz
TREBLE Boost/Cut ............................................±10 dB at 20 kHz
TREBLE Turnover Frequency ............................................3.5 kHz
• Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz)
H.P.F. (Front, Center, Surround, Surround back: Small)
......................................................................................12 dB/oct.
L.P.F. (Subwoofer) ..........................................................24 dB/oct.
VIDEO SECTION
• Video Signal Type (Gray Back)
[U.S.A., Canada, Korea and General models].......................NTSC
[Other models]..........................................................................PAL
• Video Signal Type (Video Conversion) ........................... NTSC/PAL
• Signal Level
Composite................................................................... 1 Vp-p/75 Ω
S-video [U.K., Europe and Russia models]
....................................... 1 Vp-p/75 Ω (Y), 0.286 Vp-p/75 Ω (C)
Component............................................................1 Vp-p/75 Ω (Y)
• Maximum Input Level (Video Conversion Off)
............................................................................. 1.5 Vp-p or more
• Signal to Noise Ratio...................................................50 dB or more
• Frequency Response [MONITOR OUT]
Component (Video Conversion Off)
................................................................ 5 Hz to 60 MHz, –3 dB
FM SECTION
• Tuning Range
[U.S.A. and Canada models] ............................ 87.5 to 107.9 MHz
[Asia and General models] ......... 87.5/87.50 to 108.0/108.00 MHz
[Other models].............................................. 87.50 to 108.00 MHz
• 50 dB Quieting Sensitivity (IHF)
Mono................................................................... 3.0 µV (20.8 dBf)
• Signal to Noise Ratio (IHF)
Mono/Stereo ............................................................... 74 dB/69 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo ..................................................................... 0.3/0.3%
• Antenna Input (unbalanced) .......................................................75 Ω
AM SECTION
• Tuning Range
[U.S.A. and Canada models] ................................ 530 to 1710 kHz
[Asia and General models] ...................530/531 to 1710/1611 kHz
[Other models]...................................................... 531 to 1611 kHz
GENERAL
• Power Supply
[U.S.A. and Canada models] ............................... AC 120 V, 60 Hz
[General models] ...............AC 110/120/220/230–240 V, 50/60 Hz
[China model] ...................................................... AC 220 V, 50 Hz
[Korea model]...................................................... AC 220 V, 60 Hz
[Australia model]................................................. AC 240 V, 50 Hz
[U.K., Europe and Russia models] ...................... AC 230 V, 50 Hz
[Asia models]................................... AC 220/230–240 V, 50/60 Hz
• Power Consumption
[U.S.A. and Canada models] ...................................270 W/320 VA
[Other models]...................................................................... 280 W
• Standby Power Consumption
Standby through off ....................................................0.2 W or less
Standby through on........................................................3 W or less
• Maximum Power Consumption
[Asia and General models] ................................................... 490 W
• Dimensions (W x H x D)...................................435 x 151 x 364 mm
(17-1/8 x 6 x 14-3/8 in)
• Weight...................................................................... 8.5 kg (18.7 lbs)
* Specifications are subject to change without notice.
56 En
Index
■
Numerics
A
B
■
C
E
E)Test Tone, speaker setup ............................ 41
Editing sound field program .......................... 36
Editing surround decoder ............................... 36
Effect Level, sound field parameter ............... 37
ENTER, remote control ................................... 7
EQ Type Select, D)Equalizer,
speaker setup ............................................. 41
Extended Surround, OPTION menu .............. 34
External component operation key,
remote control ............................................. 7
■
F
FL Scroll, 2 Display, function setup .............. 42
FM antenna connection .................................. 17
FM Mode, OPTION menu ............................. 34
FM tuning ...................................................... 28
FM, front panel ................................................ 4
Frequency tuning ........................................... 28
Front L, C)Distance, speaker setup ................ 41
Front left speaker ........................................... 10
Front panel ....................................................... 4
Front panel display .......................................... 6
Front panel display, front panel ....................... 4
Front R, C)Distance, speaker setup ............... 41
Front right speaker ......................................... 10
Front SP, A)Config, speaker setup ................ 40
Function setup, setup menu ........................... 42
■
H
Hall in Munich, sound field program ............ 25
Hall in Vienna, sound field program ............. 25
HDMI Auto, 2 Lipsync, sound setup ............. 41
HDMI indicator, front panel display ............... 6
HDMI information ......................................... 55
HDMI jack ..................................................... 13
HDMI OUT/HDMI 1-4, rear panel ................. 5
HDMI THROUGH, front panel ....................... 4
HDMI, troubleshooting .................................. 49
Headphones using .......................................... 22
Hi-fi sound playback ...................................... 22
High frequency sound adjustment ................. 22
■
I
INFO, front panel ............................................. 4
M
Manual Delay, 2 Lipsync, sound setup ......... 42
Max Volume, 3 Volume, function setup ....... 43
Memory guard, setup menu ........................... 43
MEMORY, front panel ................................... 4
MON.CHK, advanced setup .......................... 45
MONITOR OUT, rear panel ........................... 5
Mono Movie, sound field program ............... 25
Multi information display,
front panel display ...................................... 6
Music Video, sound field program ................ 25
MUTE indicator, front panel display .............. 6
MUTE, remote control .................................... 7
■
N
Numeric key, remote control ........................... 7
■
O
OPTICAL jack .............................................. 13
OPTIMIZER MIC jack, front panel ................ 4
OPTION menu .............................................. 33
OPTION, remote control ................................. 7
OSD Shift, 2 Display, function setup ............ 43
■
P
Pairing Bluetooth components ...................... 32
Pairing, OPTION menu ................................. 35
Panorama, decoder parameter ....................... 37
PHONES jack, front panel .............................. 4
Placing speaker .............................................. 10
PORTABLE jack, front panel ......................... 4
Power cable connection ................................. 17
Power Cable, rear panel .................................. 5
POWER, remote control ................................. 7
PRE OUT, rear panel ...................................... 5
PRESET l / h, front panel ........................... 4
Preset tuning .................................................. 28
PROGRAM l / h, front panel ...................... 4
Projector connection ...................................... 14
■
R
Registering input source ................................ 21
Registering sound field program ................... 21
Remote control ................................................ 7
Remote control code resetting ....................... 44
Remote control code setting .......................... 44
Remote control ID, advanced setup .............. 45
Remote control signal transmitter,
remote control ............................................. 7
Remote control, controlling other
component ................................................ 44
Remote control, preparation ............................ 9
Remote control, troubleshooting ................... 50
REMOTE ID, advanced setup ....................... 45
Repeat playback, iPod ................................... 31
Repeat, OPTION menu ................................. 35
Resetting remote control code ....................... 44
Resolution, 1 HDMI, function setup ............. 42
RETURN, remote control ............................... 7
57 En
English
C)Distance, speaker setup ..............................41
C.Image, decoder parameter ..........................37
Cellar Club, sound field program ...................25
Center SP, A)Config, speaker setup ...............40
Center speaker ................................................10
Center width, decoder parameter ...................37
Center, C)Distance, speaker setup .................41
Chamber, sound field program .......................25
CINEMA DSP indicator,
front panel display .......................................6
CINEMA DSP parameter ...............................36
Clear Preset, OPTION menu ..........................35
COAXIAL jack ..............................................13
CODE SET, remote control .............................7
COMPONENT VIDEO jack ..........................13
Connect, OPTION menu ................................35
Connecting AM antenna ................................17
Connecting audio and video player ................15
Connecting audio player ................................16
Connecting Bluetooth wireless audio
receiver ......................................................16
Connecting FM antenna .................................17
■
■
APPENDIX
B)Level, speaker setup ...................................41
Basic operation, setup menu ..........................39
BI-AMP connection switch,
advanced setup ..........................................45
BI-AMP, advanced setup ...............................45
Bluetooth component playback ......................32
Bluetooth wireless audio receiver
connection .................................................16
Bluetooth, troubleshooting .............................51
D
D)Equalizer, speaker setup ............................ 41
Decoder Mode, OPTION menu ..................... 34
Decoder parameter ......................................... 37
Dimension, decoder parameter ...................... 37
Dimmer, 2 Display, function setup ................ 42
DIRECT, front panel ....................................... 4
Direct, sound field parameter ........................ 37
Disconnect, OPTION menu ........................... 35
DISPLAY, remote control ............................... 7
Displaying input signal information .............. 23
DOCK terminal, rear panel .............................. 5
Drama, sound field program .......................... 25
DSP Level, sound field parameter ................. 36
DSP Parameter, setup menu .......................... 43
L
ADVANCED
OPERATION
■
■
LFE/Bass Out, A)Config, speaker setup ....... 39
Low frequency sound adjustment ................. 22
BASIC
OPERATION
A)Config, speaker setup .................................39
Action Game, sound field program ................25
Adaptive DRC, 3 Volume, function setup .....43
Adjusting high frequency sound ....................22
Adjusting low frequency sound .....................22
Advanced setup ..............................................45
Adventure, sound field program ....................24
AM antenna connection .................................17
AM tuning ......................................................28
AM, front panel ................................................4
ANTENNA jack, rear panel .............................5
Aspect, 1 HDMI, function setup ....................42
AUDIO 1/2, rear panel .....................................5
Audio and video player connection ................15
AUDIO jack ...................................................13
Audio jack ......................................................13
AUDIO L/R jack, front panel ...........................4
AUDIO OUT, rear panel ..................................5
Audio Output, 1 HDMI, function setup .........42
Audio player connection ................................16
Auto Delay, 2 Lipsync, sound setup ..............42
Auto Preset, OPTION menu ..........................35
Auto Setup (YPAO), troubleshooting ............51
Automatic setup .............................................18
AV 1-6, rear panel ............................................5
AV OUT, rear panel .........................................5
■
PREPARATION
■
INFO, remote control ...................................... 7
INIT, advanced setup .................................... 45
Init. Volume, 3 Volume, function setup ........ 43
Initialize setting, advanced setup .................. 45
INPUT l / h, front panel .............................. 4
Input selection key, remote control ................. 7
Input signal information displaying .............. 23
Input source registration ................................ 21
Installing batteries, remote control .................. 9
iPod playback ................................................ 30
iPod universal dock connection ..................... 16
iPod, troubleshooting .................................... 50
Connecting iPod universal dock .................... 16
Connecting power cable ................................ 17
Connecting projector ..................................... 14
Connecting set-top box .................................. 15
Connecting speaker ........................................ 11
Connecting speaker cable .............................. 12
Connecting TV monitor ................................. 14
Connection ..................................................... 10
Controlling other component,
remote control ........................................... 44
Crossover Freq., A)Config, speaker setup ..... 40
CT Level, sound field parameter ................... 37
Cursor indicator, front panel display ............... 6
Cursors k / n / l / h, remote control ........... 7
INTRODUCTION
1 Dynamic Range, sound setup ......................41
1 HDMI, function setup .................................42
2 Display, function setup ................................42
2 Lipsync, sound setup ...................................41
2ch Stereo, sound field program ....................25
3 Volume, function setup ...............................43
4 Input Rename, function setup .....................43
5.1-channel speaker layout .............................10
6.1-channel speaker layout .............................10
7.1-channel speaker layout .............................10
7ch Enhancer, sound field program ...............26
7ch Stereo, sound field program ....................26
Index
Roleplaying Game, sound field program ....... 25
■
S
SB Level, sound field parameter ................... 37
SCENE function ............................................ 21
SCENE, front panel ......................................... 4
SCENE, remote control ................................... 7
Sci-Fi, sound field program ........................... 24
Selecting SCENE ........................................... 21
Setting remote control code ........................... 44
Set-top box connection .................................. 15
Setup menu .................................................... 38
Setup menu basic operation ........................... 39
SETUP, remote control ................................... 7
Shuffle playback, iPod ................................... 31
Shuffle, OPTION menu ................................. 35
Signal Info parameter .................................... 34
Signal Info, OPTION menu ........................... 34
SILENT CINEMA ......................................... 27
SL Level, sound field parameter .................... 37
SLEEP indicator, front panel display .............. 6
Sleep timer ..................................................... 22
SLEEP, remote control .................................... 7
Sound field parameter .................................... 36
Sound field program editing .......................... 36
Sound field program registration ................... 21
Sound selection key, remote control ................ 7
Sound setup, setup menu ............................... 41
SOURCE POWER, remote control ................. 7
SP IMP., advanced setup ............................... 45
Speaker cable connection .............................. 12
Speaker connection ........................................ 11
Speaker impedance, advanced setup ............. 45
Speaker indicator, front panel display ............. 6
Speaker layout ............................................... 10
Speaker placement ......................................... 10
Speaker setup ................................................. 39
SPEAKERS terminal, rear panel ..................... 5
Specifications ................................................ 56
Spectacle, sound field program ..................... 24
Sports, sound field program .......................... 25
SR Level, sound field parameter ................... 37
Standard, sound field program ....................... 24
Standby Through, 1 HDMI,
function setup ............................................ 42
STANDBY/ON, front panel ............................ 4
Straight decoding mode ................................. 27
Straight Enhancer, sound field program ........ 26
STRAIGHT, front panel .................................. 4
Subwoofer ...................................................... 10
Subwoofer Phase, A)Config,
speaker setup ............................................. 40
Sur. L, C)Distance, speaker setup .................. 41
Sur. L/R SP, A)Config, speaker setup ........... 40
Sur. R, C)Distance, speaker setup ................. 41
Sur.B L, C)Distance, speaker setup ............... 41
Sur.B L/R SP, A)Config, speaker setup ........ 40
Sur.B R, C)Distance, speaker setup ............... 41
Surround back left speaker ............................ 10
Surround back right speaker .......................... 10
Surround back speaker ................................... 10
Surround decoder editing ............................... 36
Surround left speaker ..................................... 10
Surround right speaker ................................... 10
SWFR, C)Distance, speaker setup ................. 41
■
Turning off .....................................................17
Turning on ......................................................17
TV control key, remote control ........................7
TV monitor connection ..................................14
■
U
Using the remote control ..................................9
■
V
VIDEO jack ....................................................13
Video jack ......................................................13
VIDEO jack, front panel ..................................4
Video/audio jack ............................................13
Virtual CINEMA DSP ...................................27
VOLUME +/-, remote control .........................7
VOLUME control, front panel .........................4
VOLUME indicator, front panel display .........6
Volume Trim, OPTION menu .......................33
■
Y
YPAO .............................................................18
YPAO, troubleshooting ..................................51
T
The Bottom Line, sound field program ......... 25
The Roxy Theatre, sound field program ........ 25
Tone control ................................................... 22
TONE CONTROL, front panel ....................... 4
TRANSMIT, remote control ........................... 7
Troubleshooting ............................................. 46
Tuner indicator, front panel display ................ 6
Tuner key, remote control ............................... 7
Tuner, troubleshooting .................................. 49
TUNING l / h, front panel .......................... 4
Tuning, AM ................................................... 28
Tuning, FM .................................................... 28
58 En
“ASTANDBY/ON” or
“fPOWER” (example) indicates
the name of the parts on the front
panel or the remote control. Refer
to “Part names and functions” on
page 4.
List of remote control codes
TV
A.R. Systems
Acme
Acura
ADC
Admiral
0274
0260
0261, 0273
0259
0100, 0224, 0257,
0258, 0259, 0264,
0265
Advent
0204
Adventura
0107
Adyson
0260, 0327, 0328
Agashi
0327, 0328
Agazi
0259
Aiko
0260, 0261, 0273,
0274, 0327, 0328
Aim
0274
Aiwa
0028, 0297
Akai
0063, 0096, 0101,
0205, 0231, 0261,
0262, 0268, 0271,
0273, 0274, 0327,
0328
Akiba
0262, 0274
Akura
0259, 0262, 0273,
0274
Alaron
0327
Alba
0243, 0260, 0261,
0262, 0266, 0269,
0271, 0273, 0274,
0294, 0300, 0327
Albatron
0222
Alcyon
0249
Alleron
0105
Allorgan
0328
Allstar
0268, 0274
America Action 0225
AMOi
0326
Amplivision
0243, 0260, 0275,
0328
Amstrad
0259, 0261, 0262,
0273, 0274
Amtron
0104
Anam
0225, 0261
Anam National 0102, 0104
Anglo
0261, 0273
Anitech
0249, 0259, 0261,
0273, 0274
Ansonic
0243, 0250, 0261,
0263, 0273, 0274
AOC
0072, 0090, 0096,
0103
Apex
0061, 0117, 0139
Arcam
0327, 0328
Arcam Delta
0260
Aristona
0268, 0271, 0274
Arthur Martin 0275
ASA
0257, 0265
Asberg
0249, 0268, 0274
Astra
0261
Asuka
0259, 0260, 0262,
0327, 0328
Atlantic
0260, 0268, 0271,
0274, 0327
Atori
0261, 0273
Auchan
0275
Audiosonic
0243, 0260, 0261,
0262, 0268, 0271,
0274, 0328
AudioTon
0243, 0260, 0328
Audiovox
0104, 0144, 0225
Ausind
Autovox
Aventura
Awa
Axion
Baird
Bang & Olufsen
Basic Line
Bastide
Baur
Bazin
Beko
Belcor
Bell & Howell
Benq
Beon
Best
Bestar
Binatone
Blue Sky
Blue Star
Boots
BPL
Bradford
Brandt
Brillian
Brinkmann
Brionvega
Britannia
Brockwood
Broksonic
Bruns
BTC
Bush
Candle
Capsonic
Carena
Carnivale
Carrefour
Carver
Cascade
Casio
Cathay
CCE
Celebrity
Celera
Centurion
Century
CGE
Changhong
Chimei
Cimline
Citizen
City
Clarion
Clarivox
0249
0249, 0257, 0259,
0260, 0328
0097
0327, 0328
0206
0328
0230, 0257
0261, 0262, 0268,
0273, 0274, 0328
0260, 0328
0271, 0274
0328
0243, 0269, 0274,
0282, 0351, 0357,
0372, 0380
0090
0065, 0100
0051, 0160, 0315
0268, 0271, 0274
0243
0243, 0268, 0274
0260, 0328
0262, 0274
0270
0260, 0328
0270, 0274
0104, 0225
0267, 0272
0228
0274
0257, 0268, 0271,
0274
0260, 0327, 0328
0090
0063, 0225
0257
0262
0261, 0262, 0264,
0266, 0268, 0270,
0271, 0273, 0274,
0282, 0286, 0294,
0300, 0328, 0329,
0351, 0388, 0394,
0413
0072, 0090, 0096,
0107
0259
0274
0096
0266
0088
0261, 0273, 0274
0317
0268, 0271, 0274
0229, 0328
0057, 0101
0117
0268, 0271, 0274
0257
0243, 0249
0117
0323
0261, 0273
0072, 0085, 0090,
0096, 0104
0261, 0273
0225
0271
Clatronic
0243, 0249, 0259,
0260, 0261, 0262,
0268, 0269, 0273,
0274, 0328
CMS
0327
CMS Hightec 0328
Coby
0151
Colortyme
0072, 0090
Commercial Solutions
0071
Concerto
0072, 0090
Concorde
0261, 0273
Condor
0243, 0260, 0268,
0269, 0273, 0274,
0327
Contec
0225, 0260, 0261,
0266, 0273, 0327
Contec/Cony 0094, 0104
Continental Edison
0267
Cosmel
0261, 0273
Craig
0104, 0225
Crosley
0088, 0119, 0249,
0257
Crown
0104, 0225, 0243,
0249, 0261, 0268,
0269, 0271, 0273,
0274
CS Electronics 0260, 0262, 0327
CTC Clatronic 0263
CTX
0159
Curtis Mathes 0065, 0071, 0072,
0085, 0088, 0090,
0096, 0099, 0224
CXC
0104, 0225
Cybertron
0262
Cytron
0202
Daewoo
0072, 0085, 0090,
0103, 0119, 0245,
0260, 0261, 0268,
0273, 0274, 0281,
0285, 0303, 0321,
0327, 0328, 0344,
0361, 0387
Dainichi
0262, 0327
Dansai
0259, 0268, 0271,
0274, 0327, 0328
Dantax
0243, 0271
Dawa
0274
Daytron
0072, 0085, 0090,
0261, 0273
De Graaf
0264
Decca
0260, 0268, 0271,
0274, 0328
Dell
0167, 0195
Denver
0308, 0312
Desmet
0268, 0271, 0274
Diamant
0274
Diamond
0327
DiamondVision 0213, 0221
Dimensia
0099
Disney
0137
Dixi
0261, 0268, 0271,
0273, 0274, 0328
Dream Vision 0415, 0416
DTS
0261, 0273
Dual
0260, 0274, 0328
Dual-Tec
0260, 0261
Dumont
0076, 0090, 0108,
0257, 0260, 0263,
0328
Durabrand
0077, 0097, 0133,
0225
Dux
0271
Dwin
0224
Dynatron
0268, 0271, 0274
Dynex
0181, 0182
Elbe
0243, 0250, 0274,
0328
Elcit
0257
Electa
0270
ELECTRO TECH 0261
Electroband
0057, 0101
Electrograph
0226
Electrohome
0072, 0090, 0101,
0102
Element
0180
Elin
0260, 0268, 0271,
0273, 0274, 0327
Elite
0262, 0268, 0274
Elman
0263
Elta
0261, 0273, 0327
Emerson
0065, 0072, 0077,
0082, 0085, 0090,
0094, 0095, 0097,
0104, 0105, 0119,
0225, 0243, 0257,
0274
Emprex
0200
Envision
0072, 0090, 0096
Epson
0156, 0201, 0309
Erres
0268, 0271, 0274
ESA
0097
ESC
0328
Etron
0261
Eurofeel
0328
Euro-Feel
0259
Euroline
0271
Euroman
0243, 0327, 0328
Euromann
0259, 0260, 0268,
0274
Europhon
0260, 0263, 0268,
0274, 0327, 0328
Expert
0275
Exquisit
0274
Fenner
0261, 0273
Ferguson
0267, 0271, 0272
Fidelity
0260, 0264, 0274,
0327
Filsai
0328
Finlandia
0264
Finlux
0249, 0257, 0260,
0263, 0268, 0271,
0274, 0328
FIRST LINE 0260, 0261, 0268
Firstline
0273, 0274, 0327,
0328
Fisher
0065, 0243, 0257,
0260, 0266, 0269,
0328
Flint
0268, 0274
Formenti
0249, 0257, 0258,
0260, 0271, 0327
Formenti/Phoenix 0327
Fortress
0257, 0258
Fraba
0243, 0274
Friac
0243
Frontech
0259, 0261, 0264,
0265, 0273, 0328
Fujitsu
0023, 0024, 0025,
0105, 0328
Fujitsu General 0328
i
Fujitsu Siemens 0425, 0426, 0427,
0428, 0429
Funai
0033, 0034, 0035,
0036, 0037, 0097,
0104, 0105, 0225,
0259
Futuretech
0104, 0225
Galaxi
0269, 0274
Galaxis
0243, 0274
Gateway
0163, 0226, 0227
GBC
0261, 0266, 0273
GE
0069, 0071, 0072,
0073, 0077, 0090,
0099, 0102, 0106,
0112, 0131
Geant Casino 0275
GEC
0260, 0265, 0268,
0271, 0274, 0328
Geloso
0261, 0264, 0273
General Technic 0261, 0273
Genexxa
0262, 0265, 0268,
0274
GFM
0177, 0210
Giant
0328
Gibralter
0076, 0090, 0096,
0108
GoldHand
0327
Goldline
0274
GoldStar
0072, 0077, 0085,
0090, 0094, 0096,
0103, 0243, 0260,
0261, 0264, 0268,
0271, 0273, 0274,
0327, 0328
Goodmans
0164, 0259, 0261,
0266, 0268, 0271,
0273, 0274, 0322,
0328, 0395, 0399,
0412
Gorenje
0243, 0269
GPM
0262
GPX
0211
Gradiente
0162
Graetz
0265
Granada
0249, 0260, 0264,
0266, 0268, 0271,
0274, 0275, 0328
Grandin
0261, 0262, 0270,
0271
Gronic
0328
Grundig
0242, 0243, 0249,
0274, 0356
Grunpy
0104, 0105, 0225
Haier
0187, 0207
Halifax
0259, 0260, 0327,
0328
Hallmark
0072, 0077, 0090
Hampton
0260, 0327, 0328
Hanseatic
0243, 0250, 0260,
0261, 0266, 0268,
0271, 0273, 0274,
0328
Hantarex
0261, 0273, 0274
Hantor
0274
Harman/Kardon
0088
Harvard
0104, 0225
Harwood
0273, 0274
Havermy
0224
HCM
0259, 0260, 0261,
0270, 0273, 0274,
0328
Hema
0273, 0328
Hewlett Packard 0146
Higashi
0327
HiLine
0274
ii
Hinari
Hisawa
Hisense
Hitachi
Hornyphon
Hoshai
Huanyu
Hygashi
Hyper
Hypson
Hyundai
Iberia
ICE
ICeS
Ilo
IMA
Imperial
Indiana
Infinity
InFocus
Ingelen
Ingersol
Initial
Inno Hit
Innovation
Insignia
Inteq
Interactive
Interbuy
Interfunk
International
Intervision
Irradio
Isukai
ITC
ITS
ITT
ITV
Janeil
JBL
JC Penney
JCB
Jensen
JVC
0261, 0262, 0266,
0268, 0271, 0273,
0274
0262, 0270, 0275
0165
0006, 0014, 0015,
0016, 0042, 0072,
0090, 0094, 0173,
0254, 0255, 0256,
0260, 0264, 0265,
0266, 0274, 0285,
0300, 0319, 0328,
0348, 0349, 0385,
0402, 0410
0268, 0274
0262
0260, 0327
0260, 0327, 0328
0260, 0261, 0273,
0327, 0328
0259, 0260, 0268,
0270, 0271, 0274,
0275, 0328
0223
0274
0259, 0260, 0261,
0262, 0268, 0273,
0274, 0327, 0328
0327
0198, 0203
0104
0243, 0249, 0265,
0268, 0269, 0274
0268, 0271, 0274
0088
0168, 0277, 0313,
0397, 0430
0265
0261, 0273
0203
0249, 0260, 0261,
0262, 0268, 0271,
0273, 0274, 0328
0259, 0261
0182, 0188, 0190,
0209
0076
0243
0261, 0273
0243, 0257, 0265,
0268, 0271, 0274
0327
0243, 0259, 0260,
0263, 0274, 0328
0249, 0261, 0262,
0268, 0271, 0273,
0274
0262, 0274
0260, 0328
0262, 0268, 0270,
0274, 0327
0261, 0265
0261, 0271, 0274
0107
0088
0072, 0073, 0085,
0090, 0099, 0103,
0106
0057, 0101
0072, 0090
0017, 0018, 0019,
0092, 0093, 0094,
0106, 0251, 0252,
0266, 0268, 0293,
0360, 0379
Kaisui
Kamosonic
Kamp
Kapsch
Karcher
Kawasho
KEC
Kendo
Kenwood
KIC
Kingsley
KLH
Kloss Novabeam
Kneissel
Kolster
Konka
Korpel
Korting
Kosmos
Koyoda
KTV
Kyoto
Lasat
Lenco
Lenoir
Leyco
LG
LG/GoldStar
Liesenk
Liesenkotter
Life
Lifetec
Lloyds
Loewe
Loewe Opta
Logik
Luma
Lumatron
Lux May
Luxman
Luxor
LXI
M Electronic
MAG
Magnadyne
Magnafon
0260, 0261, 0262,
0270, 0273, 0274,
0327, 0328
0260
0260, 0327
0265
0243, 0260, 0261,
0271, 0274
0072, 0090, 0101,
0327
0225
0243, 0263, 0264,
0274
0072, 0090, 0096
0328
0260, 0327
0117
0104, 0107
0243, 0250, 0274
0268, 0274
0262
0268, 0271, 0274
0243, 0257
0274
0261
0085, 0096, 0104,
0225, 0229, 0260,
0328
0327, 0328
0243
0261, 0273
0260, 0261, 0273
0259, 0268, 0271,
0274
0016, 0038, 0039,
0077, 0103, 0145,
0222, 0243, 0246,
0253, 0260, 0261,
0264, 0268, 0271,
0273, 0274, 0282,
0290, 0299, 0316,
0327, 0328, 0351,
0359, 0367, 0382,
0384, 0389, 0396
0246
0271
0274
0259, 0261
0259, 0261, 0273,
0274
0273
0243, 0250, 0274,
0280, 0306, 0347
0257, 0268, 0271
0100
0264, 0271, 0273,
0274
0264, 0268, 0271,
0274, 0328
0268
0072, 0090
0260, 0264, 0328
0061, 0065, 0071,
0072, 0073, 0077,
0088, 0099
0260, 0261, 0265,
0267, 0268, 0271
0050
0257, 0263, 0271
0249, 0260, 0263,
0327
Magnavox
0072, 0088, 0090,
0091, 0095, 0096,
0098, 0114, 0115,
0129, 0134, 0176,
0178, 0189, 0210
Magnum
0259, 0261
Majestic
0100
Mandor
0259
Manesth
0259, 0260, 0268,
0271, 0274, 0328
Marantz
0072, 0088, 0090,
0096, 0158, 0268,
0271, 0274
Marelli
0257
Mark
0268, 0271, 0273,
0274, 0327, 0328
Masuda
0328
Matsui
0260, 0261, 0264,
0266, 0268, 0271,
0273, 0274, 0328,
0405
Matsushita
0067
Maxent
0193, 0226
Mediator
0268, 0271, 0274
Medion
0259, 0261, 0274
Megapower
0222
Megatron
0072, 0077
MElectronic
0273, 0274, 0327,
0328
Melvox
0275
Memorex
0065, 0072, 0077,
0100, 0103, 0133,
0219, 0261, 0273
Memphis
0261, 0273
Mercury
0273, 0274
Metz
0257
MGA
0072, 0077, 0090,
0096, 0103
Micromaxx
0259, 0261
Microstar
0259, 0261
Midland
0069, 0071, 0073,
0076, 0085, 0106,
0108
Minerva
0249
Minoka
0268, 0274
Mintek
0203
Mitsubishi
0006, 0015, 0016,
0048, 0072, 0077,
0090, 0103, 0196,
0224, 0257, 0266,
0268, 0274, 0298,
0371
Mivar
0243, 0249, 0250,
0260, 0327, 0328
Monivision
0222
Montgomery Ward
0100
Motion
0249
Motorola
0102, 0224
MTC
0072, 0090, 0096,
0103, 0243, 0327
Multi System 0271
Multitech
0104, 0225, 0229,
0243, 0260, 0261,
0263, 0264, 0266,
0271, 0273, 0274,
0327, 0328
Murphy
0260, 0327
NAD
0061, 0072, 0077
Naonis
0264
NEC
0026, 0053, 0072,
0090, 0096, 0102,
0103, 0266, 0328
Neckermann
NEI
Net-TV
Neufunk
New Tech
New World
NewTech
Nicamagic
Nikkai
Nikko
Nobliko
Nokia
Norcent
Nordic
Nordmende
Nordvision
Novatronic
Oceanic
Okano
Olevia
ONCEAS
Onwa
Opera
Oppo
Optimus
Optoma
Optonica
Orbit
Orion
Orline
Osaki
Oso
Otto Versand
Pael
Palladium
Palsonic
Panama
Panasonic
Panavision
Pathe Cinema
Pausa
Penney
Perdio
Perfekt
Philco
Philharmonic
Philips
0243, 0257, 0260,
0264, 0268, 0269,
0271, 0274, 0328
0268, 0271, 0274
0226
0273, 0274
0261, 0268
0262
0273, 0274, 0328
0260, 0327
0259, 0260, 0262,
0268, 0271, 0273,
0274, 0327, 0328
0072, 0077, 0096
0249, 0260, 0263,
0327
0265
0155
0328
0257, 0265, 0267,
0268
0271
0274
0265, 0275
0243, 0269, 0274
0052, 0140, 0149,
0154, 0157
0260
0104, 0225
0274
0208
0065, 0067
0194
0224
0268, 0274
0121, 0192, 0261,
0268, 0271, 0273,
0274, 0282, 0329
0274
0259, 0260, 0262,
0274, 0328
0262
0258, 0260, 0266,
0268, 0270, 0271,
0274, 0328
0260, 0327
0243, 0260, 0269,
0274, 0328
0328
0259, 0260, 0261,
0273, 0274, 0327,
0328
0006, 0007, 0066,
0067, 0068, 0069,
0070, 0102, 0106,
0113, 0147, 0215,
0241, 0265, 0274,
0279, 0310, 0332,
0334, 0368, 0374
0274
0243, 0250, 0260,
0275, 0327
0261, 0273
0061, 0069, 0071,
0077, 0096
0274, 0327
0274
0072, 0088, 0090,
0091, 0094, 0096,
0102, 0103, 0243,
0249, 0257, 0274
0260, 0328
0040, 0088, 0089,
0090, 0091, 0094,
0098, 0099, 0102,
0114, 0135, 0143,
0176, 0178, 0189,
0210, 0212, 0232,
0233, 0257, 0260,
0268, 0271, 0274,
0278, 0287, 0301,
0302, 0307, 0311,
0314, 0330, 0331,
0333, 0337, 0338,
0339, 0341, 0343,
0345, 0355, 0363,
0365, 0377, 0378,
0381, 0383, 0406,
0409, 0414
Philips Magnavox 0089, 0114, 0115
Phoenix
0243, 0257, 0268,
0271, 0274, 0327
Phonola
0257, 0268, 0271,
0274, 0327
Pilot
0085, 0090, 0096
Pioneer
0012, 0013, 0072,
0090, 0243, 0265,
0267, 0268, 0271,
0274, 0408
Plantron
0259, 0268, 0273,
0274
Playsonic
0328
Polaroid
0117, 0152, 0184,
0220
Poppy
0261, 0273
Portland
0072, 0085, 0090,
0103
Prandoni-Prince
0249, 0264
Precision
0260, 0328
Prima
0161, 0207, 0261,
0265, 0273
Princeton
0222
Prism
0069, 0106
Profex
0261, 0273
Profi-Tronic
0268, 0274
Proline
0268, 0274
Proscan
0071, 0073, 0099
Prosonic
0243, 0260, 0271,
0274, 0327, 0328
Protech
0259, 0260, 0261,
0263, 0268, 0271,
0328
Proton
0072, 0077, 0090,
0094
Protron
0150
PROVIEW
0050, 0164
Provision
0271, 0274
Pulsar
0076, 0090, 0108
Pye
0268, 0271, 0274,
0296, 0338
Pymi
0261, 0273
Quandra Vision
0275
Quasar
0067, 0069, 0102,
0106
Quelle
0259, 0260, 0268,
0271, 0274, 0328
Questa
0266
Radialva
0274
RadioShack
0065, 0071, 0077,
0096, 0225, 0274
RadioShack/Realistic
0072, 0085, 0090,
0094, 0099, 0104
Radiola
0268, 0271, 0274,
0328
Radiomarelli
0257, 0274
Radiotone
0243, 0268, 0273,
0274
Rank
0266
RCA
Realistic
Recor
Redstar
Reflex
Revox
Rex
RFT
Rhapsody
R-Line
Roadstar
Robotron
Rowa
Royal Lux
RTF
Runco
Saba
Saisho
Salora
Sambers
Sampo
Samsung
Sandra
Sansui
Sanyo
SBR
Sceptre
Schaub Lorenz
Schneider
Scotch
Scott
Sears
SEG
SEI
0071, 0072, 0073,
0074, 0075, 0090,
0099, 0102, 0103,
0109, 0120, 0179,
0218
0065, 0077, 0096,
0225
0274
0274
0274
0243, 0268, 0271,
0274
0259, 0264, 0265
0243, 0250, 0257
0327
0268, 0271, 0274
0259, 0261, 0262,
0273
0257
0327, 0328
0243
0257
0076, 0096, 0108
0257, 0265, 0267,
0272, 0376
0259, 0260, 0261,
0273, 0328
0264, 0265
0249, 0263
0072, 0085, 0090,
0096, 0226
0029, 0030, 0031,
0032, 0044, 0045,
0046, 0047, 0072,
0077, 0084, 0085,
0086, 0087, 0090,
0094, 0096, 0103,
0118, 0217, 0229,
0235, 0236, 0237,
0243, 0259, 0260,
0261, 0268, 0269,
0271, 0273, 0274,
0284, 0295, 0327,
0328, 0336, 0346,
0390, 0407
0260, 0327, 0328
0063, 0121, 0268,
0274
0020, 0021, 0022,
0049, 0065, 0090,
0141, 0191, 0243,
0250, 0260, 0266,
0273, 0291, 0327,
0328, 0370, 0373,
0391
0271, 0274
0166, 0185
0265
0260, 0262, 0268,
0271, 0274, 0287,
0300, 0328, 0364,
0366
0072, 0077
0072, 0077, 0090,
0094, 0104, 0105,
0199, 0225
0061, 0065, 0071,
0072, 0073, 0077,
0088, 0090, 0097,
0099, 0105
0259, 0260, 0263,
0266, 0271, 0273,
0274, 0300, 0327,
0328
0274
SEI-Sinudyne
Seleco
Sencora
Sentra
Serino
Sharp
Sheng Chia
Shogun
Siarem
Sierra
Siesta
Signature
Silva
Silver
Singer
Sinudyne
Skantic
Solavox
Sonitron
Sonoko
Sonolor
Sontec
Sony
Sound & Vision
Soundesign
Soundwave
Squareview
SSS
Standard
Starlite
Stenway
Stern
Strato
Stylandia
Sunkai
Sunstar
Sunwood
Superla
Superscan
SuperTech
Supra
Supre-Macy
Supreme
Susumu
Sutron
SVA
Sydney
0257, 0263, 0265
0264, 0265, 0266
0261, 0273
0273
0327
0009, 0010, 0011,
0072, 0080, 0081,
0082, 0083, 0085,
0090, 0094, 0110,
0148, 0183, 0216,
0224, 0247, 0248,
0258, 0266, 0288,
0304, 0324, 0325,
0340, 0358, 0362,
0369, 0386, 0392,
0398, 0400, 0401,
0403
0224
0090
0257, 0263, 0274
0268, 0274
0243
0100
0327
0266
0257, 0263, 0275
0257, 0263, 0271,
0274
0265
0265
0243, 0328
0259, 0260, 0261,
0268, 0271, 0273,
0274, 0328
0265, 0275
0243, 0268, 0271,
0274
0041, 0057, 0058,
0059, 0060, 0101,
0116, 0125, 0126,
0127, 0142, 0169,
0170, 0171, 0172,
0174, 0234, 0261,
0266, 0276, 0289,
0292, 0393, 0411
0262, 0263
0072, 0077, 0090,
0104, 0105, 0225
0268, 0271, 0274
0097
0090, 0104, 0225
0260, 0261, 0262,
0268, 0273, 0274,
0328
0104, 0225, 0271,
0273, 0274
0270
0264, 0265
0273, 0274
0328
0261
0273, 0274
0261, 0268, 0273,
0274
0260, 0327, 0328
0095, 0224
0273, 0274, 0327
0261, 0273
0107
0057, 0101
0262
0261, 0273
0197
0260, 0327, 0328
iii
Sylvania
Symphonic
Syntax
Syntax-Brillian
Sysline
Sytong
Tandy
Tashiko
Tatung
TCM
Teac
Tec
Technics
TechniSat
Techwood
TEDELEX
Teknika
Teleavia
Telecor
Telefunken
Telegazi
Telemeister
Telesonic
Telestar
Teletech
Teleton
Televideon
Televiso
Tensai
Tesmet
Tevion
Texet
Thomson
Thorn
TMK
TNCi
Tokai
Tokyo
Tomashi
Toshiba
Totevision
Towada
Trakton
Trans Continens
Transtec
Trident
iv
0072, 0088, 0089,
0090, 0091, 0095,
0096, 0097, 0098,
0175, 0177, 0210
0097, 0104, 0108,
0133, 0210, 0225
0149
0149
0271
0327
0224, 0258, 0260,
0262, 0265, 0328
0260, 0264, 0266,
0327, 0328
0102, 0227, 0260,
0268, 0271, 0274,
0328
0259, 0261
0274, 0328
0260, 0261, 0273,
0328
0067, 0069, 0106
0320, 0417, 0418,
0419
0069, 0072, 0090,
0106
0328
0072, 0085, 0088,
0090, 0094, 0100,
0103, 0104, 0105,
0225
0267
0274, 0328
0267, 0268, 0272,
0274
0274
0274
0274
0274
0261, 0271, 0273,
0274
0260, 0328
0327
0275
0261, 0262, 0268,
0273, 0274, 0328
0268
0259, 0261
0260, 0273, 0327,
0328
0238, 0239, 0240,
0260, 0267, 0268,
0272, 0274, 0335
0271, 0274
0072, 0077, 0090
0076
0268, 0274, 0328
0260, 0327
0270
0027, 0043, 0053,
0054, 0061, 0062,
0063, 0064, 0065,
0122, 0123, 0124,
0128, 0130, 0132,
0139, 0214, 0244,
0266, 0283, 0305,
0328, 0329, 0342,
0350, 0352, 0353,
0354, 0375, 0404
0085
0265, 0328
0328
0274, 0328
0327
0328
Triumph
Uher
0274
0243, 0249, 0265,
0268, 0274
Ultravox
0257, 0260, 0263,
0274, 0327
Unic Line
0274
United
0271
Universum
0243, 0249, 0259,
0268, 0269, 0271,
0274, 0328
Univox
0274
Vector Research
0096
Vestel
0264, 0265, 0268,
0269, 0271, 0274,
0328
Vexa
0261, 0271, 0273,
0274
Victor
0093, 0266, 0268
VIDEOLOGIC 0327
Videologique 0260, 0262, 0327,
0328
VideoSystem 0268, 0274
Videotechnic 0327, 0328
Vidikron
0088
Vidtech
0072, 0077, 0090,
0103
Viewsonic
0153, 0186, 0226,
0318
Viking
0107
Viore
0198
Visiola
0260, 0327
Vision
0268, 0274, 0328
Vizio
0090, 0136, 0160,
0227, 0420, 0421,
0422, 0423, 0424
Vortec
0268, 0271, 0274
Voxson
0249, 0257, 0264,
0265, 0268, 0274
Waltham
0260, 0274, 0328
Wards
0072, 0077, 0088,
0090, 0091, 0096,
0098, 0099, 0100,
0103, 0105
Watson
0268, 0271, 0274
Watt Radio
0260, 0263, 0327
Waycon
0061
Wega
0257, 0266, 0274
Wegavox
0273
Weltblick
0268, 0271, 0274,
0328
Westinghouse 0057, 0138, 0142
White Westinghouse
0008, 0119, 0260,
0263, 0271, 0274,
0327
Wincom
0055, 0056
Xrypton
0274
Yamaha
0000, 0001, 0002,
0003, 0004, 0005,
0072, 0090, 0096,
0103
Yamishi
0274, 0328
Yokan
0274
Yoko
0243, 0259, 0260,
0261, 0262, 0268,
0271, 0273, 0274,
0327, 0328
Yorx
0262
Zanussi
0264, 0328
Zenith
0076, 0077, 0078,
0079, 0090, 0100,
0108, 0111
VCR
ABS
1066
Adventura
Adyson
Aiwa
1023
1090
1023, 1072, 1073,
1074
Akai
1071, 1073
Akiba
1079, 1090
Akura
1073, 1079, 1090
Alba
1074, 1075, 1076,
1079, 1090, 1091
Alienware
1066
Ambassador
1076
American High 1022
Amstrad
1072, 1090, 1091
Anitech
1079, 1090
Apex
1010
ASA
1077, 1078
Asha
1020
Asuka
1072, 1077, 1078,
1079, 1090
Audio Dynamics 1018
Audiosonic
1091
Audiovox
1021
Baird
1072, 1073, 1075,
1091
Bang & Olufsen 1067
Basic Line
1074, 1075, 1076,
1079, 1090, 1091
Baur
1078
Beaumark
1020
Bell & Howell 1019
Bestar
1075, 1076, 1091
Black Panther Line
1075, 1091
Blaupunkt
1078
Bondstec
1076, 1090
Broksonic
1054
Bush
1074, 1075, 1079,
1090, 1091, 1097,
1099, 1109, 1139
Calix
1021
Candle
1020, 1021
Canon
1022
Cathay
1091
Catron
1076
CGE
1072, 1073
Cimline
1074, 1079, 1090
CineVision
1058
Citizen
1020, 1021
Clatronic
1076, 1090
Colortyme
1018
Condor
1075, 1076, 1091
Craig
1020, 1021
Crown
1075, 1076, 1079,
1090, 1091
Curtis Mathes 1018, 1020, 1022
Cybernex
1020
CyberPower
1066
Daewoo
1023, 1075, 1076,
1091, 1116, 1141
Dansai
1079, 1090, 1091
Dantax
1074
Daytron
1075, 1091
DBX
1018
De Graaf
1078
Decca
1072, 1073, 1078
Dell
1066
Denko
1090
DiamondVision 1050
DigiFusion
1092
DIRECTV
1035, 1038, 1040,
1059, 1060, 1061,
1065
Dish Network 1064
Dishpro
1064
Dual
1073, 1078, 1091
Dumont
Durabrand
Dynatech
Echostar
Elbe
Elcatech
Electrohome
Electrophonic
Elsay
Elta
Emerson
1072, 1078
1032
1023
1064
1091
1090
1021
1021
1090
1079, 1090, 1091
1021, 1022, 1023,
1070, 1090
ESC
1075, 1091
Etzuko
1079, 1090
Expressvu
1064
Ferguson
1073
Fidelity
1072, 1090
Finlandia
1078
Finlux
1072, 1073, 1078
Firstline
1074, 1077, 1079,
1090
Fisher
1019
Flint
1074
Formenti/Phoenix 1078
Frontech
1076
Fuji
1022
Fujitsu
1072
Funai
1023, 1072
Galaxy
1072
Garrard
1023
Gateway
1066
GBC
1076, 1079
GE
1020, 1022
GEC
1078
Geloso
1079
General
1076
General Technic 1074
GOI
1064
GoldHand
1079, 1090
Goldstar
1018, 1021, 1072,
1077
Goodmans
1072, 1075, 1076,
1077, 1079, 1090,
1091
Gradiente
1023
Graetz
1073
Granada
1078
Grandin
1072, 1075, 1076,
1077, 1079, 1090,
1091
Grundig
1078, 1079
Hanseatic
1077, 1078, 1091
Harley Davidson 1023
Harman/Kardon
1018
Harwood
1090
HCM
1079, 1090
Headquarter
1019
Hewlett Packard 1066
Hinari
1074, 1079, 1090,
1091
Hisawa
1074
Hitachi
1072, 1073, 1078,
1089, 1108, 1124
HNS
1060
Howard Computers
1066
HP
1066
HTS
1064
Hughes
1035, 1040, 1061
Hughes Network Systems
1038, 1060
Humax
1035, 1060, 1094
Hush
1066
Hypson
1074, 1079, 1090,
1091
iBUYPOWER
Impego
Imperial
Inno Hit
1066
1076
1072
1075, 1076, 1078,
1079, 1090, 1091
Innovation
1074
Instant Replay 1022
Interbuy
1077, 1090
Interfunk
1078
Intervision
1072, 1091
Irradio
1077, 1079, 1090
ITT
1073
ITV
1075, 1077, 1091
JC Penney
1018, 1019, 1020,
1021, 1022
JCL
1022
JVC
1011, 1012, 1013,
1014, 1015, 1016,
1017, 1018, 1019,
1028, 1035, 1064,
1073, 1085, 1117,
1130, 1131, 1133,
1134, 1135, 1136
Kaisui
1079, 1090
Karcher
1078
Kendo
1074, 1075, 1076,
1090
Kenwood
1018, 1019, 1073
Kodak
1021, 1022
Korpel
1079, 1090
Kyoto
1090
Lenco
1075
Leyco
1079, 1090
LG
1021, 1053, 1072,
1077, 1088, 1100,
1106, 1125, 1143
Lifetec
1074
Linksys
1066
Lloyd’s
1023
Loewe Opta
1077, 1078
Logik
1079, 1090
Lumatron
1075, 1091
Luxor
1090
LXI
1021
M Electronic 1072
Magnavox
1022, 1032, 1044,
1070
Magnin
1021
Manesth
1079, 1090
Marantz
1018, 1019, 1022,
1078
Mark
1091
Marta
1021
Matsui
1074, 1077
Matsushita
1022
Media Center PC 1066
Mediator
1078
Medion
1074
MEI
1022
Memorex
1019, 1020, 1021,
1022, 1023, 1032,
1048, 1069, 1072,
1077
Memphis
1079, 1090
MGN Technology 1020
Micromaxx
1074
Microsoft
1066
Microstar
1074
Migros
1072
Mind
1066
Mitsubishi
1029, 1072, 1078
Motorola
1022
MTC
1020
Multitech
1020, 1023, 1072,
1076, 1078, 1079,
1090
Murphy
1072
NEC
1018, 1019, 1073
Neckermann
1073, 1078
NEI
1078
Nesco
1079, 1090
Nikkai
1076, 1090, 1091
Nikko
1021
Niveus Media 1066
Noblex
1020
Nokia
1073, 1091
Nordmende
1073
Northgate
1066
Oceanic
1072, 1073
Okano
1074, 1090, 1091
Olympus
1022
Optimus
1021
Orion
1033, 1069, 1074,
1097, 1139
Orson
1072
Osaki
1072, 1077, 1079,
1090
Otto Versand 1078
Palladium
1073, 1077, 1079,
1090
Panasonic
1007, 1008, 1009,
1022, 1026, 1042,
1043, 1068, 1082,
1101, 1126, 1132
Pathe Marconi 1073
Perdio
1072
Philco
1022, 1090
Philips
1022, 1030, 1035,
1038, 1039, 1040,
1044, 1055, 1060,
1078, 1084, 1095,
1096, 1104, 1105,
1111, 1113, 1122,
1124, 1127, 1128,
1129
Philips Magnavox 1030
Phonola
1078
Pilot
1021
Pioneer
1078, 1118
Polaroid
1010, 1049
Portland
1075, 1076, 1091
Prinz
1072
Profex
1079
Proline
1072
Proscan
1065
Prosonic
1074, 1091
Pulsar
1032
Pye
1052, 1078
Quarter
1019
Quartz
1019
Quasar
1022
Quelle
1072, 1078
Radialva
1090
RadioShack
1021
RadioShack/Realistic
1019, 1020, 1021,
1022, 1023
Radiola
1078
Radix
1021
Randex
1021
RCA
1020, 1022, 1025,
1035, 1040, 1047,
1060, 1065
Realistic
1019, 1020, 1021,
1022, 1023
ReplayTV
1041, 1068
Rex
1073
RFT
1076, 1078, 1090
Ricavision
Roadstar
1066
1075, 1077, 1079,
1090, 1091
Royal
1090
Runco
1032
Saba
1073
Saisho
1074, 1079
Samsung
1006, 1020, 1038,
1040, 1046, 1060,
1080, 1107, 1110,
1112, 1121, 1123,
1140, 1142
Samurai
1076, 1090
Sanky
1032
Sansui
1033, 1056, 1069,
1073
Sanyo
1019, 1020, 1114
Saville
1091
SBR
1078
Schaub Lorenz 1072, 1073
Schneider
1072, 1074, 1075,
1076, 1077, 1078,
1079, 1090, 1091
Sears
1019, 1021, 1022
SEG
1079, 1090, 1091
SEI-Sinudyne 1078
Seleco
1073
Sentra
1076, 1090
Sentron
1079, 1090
Sharp
1031, 1045, 1057,
1081, 1115, 1137
Shintom
1079, 1090
Shivaki
1077
Shogun
1020
Siemens
1077
Silva
1077
Silver
1091
Singer
1022
Sinudyne
1078
Solavox
1076
Sonic Blue
1041, 1068
Sonneclair
1090
Sonoko
1075, 1091
Sontec
1077
Sony
1000, 1001, 1002,
1003, 1024, 1027,
1036, 1062, 1066,
1083, 1098, 1103,
1138
Stack
1066
Stack 9
1066
Standard
1075, 1091
Stern
1091
STS
1022
Sunkai
1074
Sunstar
1072
Suntronic
1072
Sunwood
1079, 1090
Superscan
1070
Sylvania
1022, 1023, 1044,
1052, 1070
Symphonic
1023, 1044, 1090
Systemax
1066
Tagar Systems 1066
Taisho
1074
Tandberg
1091
Tandy
1019
Tashiko
1021, 1072
Tatung
1072, 1073, 1078
TCM
1074, 1093, 1120
Teac
1023, 1091
Tec
1076, 1090, 1091
Technics
1022
Teknika
1021, 1022, 1023
Teleavia
1073
Telefunken
Teletech
Tenosal
Tensai
1073
1090, 1091
1079, 1090
1072, 1077, 1079,
1090
Tevion
1074
Thomson
1073, 1087
Thorn
1073
Tivo
1035, 1036, 1037,
1039, 1040, 1060,
1061, 1062
TMK
1020
Tokai
1077, 1079, 1090
Tonsai
1079
Toshiba
1004, 1005, 1034,
1051, 1063, 1066,
1073, 1078, 1086,
1099, 1102, 1119,
1144
Totevision
1020, 1021
Touch
1066
Towada
1079, 1090
Towika
1079, 1090
TVA
1076
Uher
1077
UltimateTV
1065
Ultravox
1091
Unitech
1020
United Quick Star 1075, 1091
Universum
1072, 1077, 1078
Vector Research 1018
Video Concepts 1018
Videon
1074
Videosonic
1020
Viewsonic
1066
Voodoo
1066
Wards
1020, 1021, 1022,
1023
Weltblick
1077
XR-1000
1022, 1023
Yamaha
1018, 1019
Yamishi
1079, 1090
Yokan
1079, 1090
Yoko
1076, 1077, 1079,
1090
Zenith
1032
ZT Group
1066
DVD
4Kus
Accurian
Advent
AEG
Airis
Aiwa
Akai
2097
2220
2169, 2201
2312
2318
2272
2170, 2195, 2225,
2227
Akura
2310
Alba
2018, 2232, 2247,
2259, 2264
Alco
2199
Alize
2315
Allegro
2215
Amitech
2312
Amphion MediaWorks
2145
AMW
2145, 2313
Apex
2044, 2045, 2046,
2047, 2076, 2208,
2209
Apple
2163
Arrgo
2216
Asono
2318
Aspire
2140, 2202
Astar
2162
v
ATACOM
Audiovox
Avious
Awa
Axion
Bang & Olufsen
Baze
BBK
Bellagio
Best Buy
Blaupunkt
Blue Parade
Boghe
Brainwave
Brandt
Broksonic
Bush
2318
2111, 2199
2317
2313
2171
2210
2317
2318
2313
2309
2209
2207
2300
2312
2198, 2238
2192, 2195
2018, 2060, 2248,
2264, 2301, 2308,
2317, 2350, 2368
California Audio Labs
2197
Cambridge Audio 2304
CAT
2306, 2307
CAVS
2146
Centrum
2307
CGV
2304, 2312
Changhong
2222
Cinetec
2313
CineVision
2191, 2215
Clatronic
2308, 2317
Coby
2077, 2124, 2314
Conia
2301
Continental Edison
2313
Crown
2312
C-Tech
2305
Curtis Mathes 2217
CVG
2299
CyberHome
2048, 2068, 2216,
2233, 2258
Cytron
2166
Daenyx
2313
Daewoo
2083, 2215, 2280,
2299, 2312, 2313,
2326, 2376
Daewoo International
2313
Dalton
2311
Dansai
2303, 2312
Daytek
2145, 2234, 2313
Dayton
2313
DEC
2308
Decca
2312
Denon
2105, 2147, 2197,
2286
Denver
2288, 2308, 2310,
2314
Denzel
2302
Desay
2159
Diamond
2304, 2305
DiamondVision 2179, 2186
Disney
2078, 2088
DK Digital
2257
Dmtech
2226
Dual
2302
Durabrand
2218
DVX
2305
Easy Home
2309
Eclipse
2304
E-Dem
2318
Electrohome
2312
Elin
2312
Elta
2263, 2312, 2315
Emerson
2196, 2211, 2219
Enterprise
2211
vi
Enzer
Epson
ESA
Finlux
Fintec
Fisher
Funai
Gateway
GE
Gericom
GFM
Giec
Global Solutions
Global Sphere
Go Video
Goodmans
2302
2165
2219
2304, 2312, 2317
2299
2212
2219
2097
2079, 2206, 2209
2269
2176
2300
2305
2305
2135, 2215
2247, 2289, 2298,
2300, 2308, 2330,
2369
GPX
2177
Gradiente
2197
Graetz
2302
Greenhill
2209
Grundig
2271
Grunkel
2312, 2316
GVG
2299
H&B
2308
H_her
2318
Haaz
2304, 2305
Haier
2172
Harman/Kardon
2125, 2213
HiMAX
2309
Hitachi
2008, 2033, 2108,
2302, 2309, 2320,
2366
Hiteker
2208
Home Tech Industries
2318
Hyundai
2316
Ilo
2167
Initial
2167, 2209
Innovation
2228
Insignia
2080, 2175, 2219
Integra
2207
Irradio
2103
iSymphony
2164
JBL
2213
JVC
2049, 2050, 2051,
2052, 2053, 2054,
2055, 2056, 2057,
2070, 2242, 2261,
2275, 2276, 2277,
2278, 2339, 2340,
2341, 2342, 2386,
2387, 2389, 2390,
2391
Jwin
2148
Kansai
2314
Kawasaki
2199
Kennex
2312
Kenwood
2123, 2197, 2270
KeyPlug
2312
Kiiro
2312
Kingavon
2308
Kiss
2302
KLH
2199, 2209
Koda
2308
Koss
2095, 2198, 2204
KXD
2309
Landel
2221
Lasonic
2214
Lawson
2305
Lecson
2303
Lenco
2308, 2312, 2317
Lenoxx
2203, 2218
LG
Life
Lifetec
Limit
Liquid Video
Liteon
Loewe
LogicLab
Magnavox
Magnex
Majestic
Marantz
Marquant
Matsui
McIntosh
Mecotek
Medion
Memorex
MiCO
Micromaxx
Microsoft
Microstar
Minoka
Minowa
Mintek
Mitsubishi
Mizuda
Monyka
Mustek
Mx Onda
Mystral
Naiko
Nesa
Neufunk
Nevir
Next Base
Nexxtech
NU-TEC
Onkyo
Oopla
Oppo
Optim
Optimus
Orava
Orbit
Orion
Oritron
P&B
Pacific
Panasonic
Parasound
peeKTON
Philips
2080, 2107, 2115,
2116, 2141, 2188,
2211, 2215, 2237,
2239, 2285, 2293,
2295, 2348, 2370
2228
2228
2305
2204
2097, 2121, 2220
2274
2305
2075, 2096, 2178,
2180, 2196, 2205,
2219, 2308
2317
2314
2282
2312
2198, 2296
2149
2312
2228
2078, 2184, 2195
2300, 2304
2228
2206
2228
2312
2317
2167, 2209
2081
2308, 2309
2302
2232
2304
2316
2312
2209
2302
2312
2221
2161
2301
2205, 2290
2097
2150, 2173
2303
2230
2308
2313
2027, 2060
2198, 2204
2308
2305
2015, 2016, 2017,
2036, 2037, 2038,
2039, 2040, 2041,
2042, 2043, 2074,
2089, 2104, 2108,
2112, 2120, 2131,
2132, 2197, 2205,
2244, 2245, 2246,
2253, 2254, 2255,
2292, 2321, 2324,
2327, 2328, 2329,
2331, 2383, 2388
2151
2318
2026, 2061, 2062,
2075, 2090, 2094,
2096, 2097, 2103,
2110, 2126, 2180,
2193, 2205, 2231,
2235, 2241, 2251,
Phonotrend
Pioneer
Pointer
Polaroid
Portland
Powerpoint
Prima
Proceed
Proscan
Prosonic
Protron
Provision
Pye
Qwestar
Raite
RCA
RedStar
Regent
Reoc
Rimax
Rio
Roadstar
Ronin
Rotel
Rowa
Rownsonic
Saba
Sabaki
Saivod
Sampo
Samsung
Sansui
Sanyo
ScanMagic
Schaub Lorenz
Schneider
Scientific Labs
Scott
Seeltech
SEG
Sharp
Shinsonic
Sigmatek
Silva
Singer
Skymaster
2252, 2256, 2260,
2268, 2282, 2332,
2333, 2343, 2344,
2345, 2367, 2371,
2373, 2380, 2382,
2385
2317
2012, 2013, 2014,
2063, 2064, 2065,
2066, 2067, 2113,
2134, 2207, 2230,
2236, 2265, 2266,
2267, 2297, 2322,
2351, 2352, 2353,
2354, 2355, 2356,
2357, 2358, 2359,
2377
2312
2047, 2133, 2185
2312
2313
2174
2208
2206
2299, 2314
2152
2308
2194
2198
2302
2058, 2059, 2071,
2079, 2183, 2199,
2206, 2207, 2209
2310, 2312, 2314
2203
2305
2315
2215
2281, 2308
2313
2153
2200, 2301
2307
2198, 2238
2305
2312
2223
2031, 2032, 2033,
2034, 2035, 2082,
2127, 2137, 2138,
2154, 2182, 2197,
2283, 2319, 2325,
2346, 2347, 2349,
2372, 2381
2027, 2195, 2304,
2305, 2312
2139, 2195, 2212,
2374
2232
2312
2226
2305
2243, 2311
2318
2240, 2302, 2305,
2313
2009, 2010, 2084,
2122, 2142, 2143,
2144, 2181, 2190,
2228, 2262, 2375
2167
2309, 2318
2310
2304, 2305
2279, 2305
Skyworth
Slim Art
SM Electronic
Sonic Blue
Sontech
Sony
2310
2312
2305
2215
2316
2005, 2006, 2007,
2020, 2021, 2022,
2023, 2024, 2025,
2069, 2072, 2073,
2085, 2086, 2087,
2091, 2092, 2093,
2102, 2128, 2129,
2130, 2249, 2250,
2323, 2334, 2335,
2336, 2360, 2361,
2362, 2363, 2364,
2365, 2384
Soundmaster
2305
Soundmax
2305
Spectra
2313
Spectroniq
2155
Standard
2305
Star Cluster
2305
Starmedia
2308, 2318
Sungale
2158
Sunkai
2312
Superscan
2196
Supervision
2305
Sylvania
2094, 2180, 2189,
2196, 2219, 2224
Symphonic
2062, 2180
Synn
2305
T.D.E. Systems 2316
Tatung
2083, 2312
TCM
2228, 2379
Teac
2199, 2287, 2301,
2305
Tec
2310
Technics
2197
Technika
2312, 2317
Telefunken
2307
Tensai
2312
Tevion
2228, 2305, 2311
Theta Digital 2207
Thomson
2229, 2238, 2284,
2294
Tokai
2302, 2310
Top Suxess
2318
Toshiba
2004, 2026, 2027,
2028, 2029, 2030,
2098, 2099, 2100,
2101, 2114, 2117,
2118, 2119, 2136,
2187, 2195, 2205,
2291, 2337, 2338,
2378
TRANScontinents
2313, 2317
Transonic
2317
Trio
2312
Trutech
2160
TruVision
2309
TSM
2318
Umax
2315
United
2317
Urban Concepts 2205
US Logic
2167
Venturer
2199
Viewmaster
2318
Vocopro
2156
VocoStar
2157
Waitec
2318
Welltech
2300
Westinghouse 2109, 2168
Wharfedale
2304, 2305
Woxter
Xbox
Xlogic
XMS
Xoro
Yamada
Yamaha
Yamakawa
Yukai
Zenith
2315, 2318
2206, 2229
2305, 2312
2312
2300
2097, 2313, 2315
2000, 2001, 2002,
2003, 2011, 2018,
2019, 2036, 2106,
2197, 2273
2302, 2313
2232
2080, 2141, 2205,
2211, 2215
Blu-ray Disc
LG
Panasonic
Pioneer
Samsung
Sharp
Sony
Yamaha
2115
2089, 2131, 2132
2134
2035, 2127
2142, 2143, 2144
2025
2018
DVR
Bush
Panasonic
Philips
Pioneer
RCA
Samsung
Yamaha
2060
2037, 2038, 2039,
2040, 2041, 2042
2061, 2062
2063, 2064, 2065,
2066, 2067
2059
2035
2036
DVD Recorder
Aspire
Astar
Broksonic
Go Video
Hitachi
Insignia
Irradio
JVC
LG
Liteon
Panasonic
Philips
Pioneer
Pye
Samsung
Sansui
Sanyo
Sony
Sylvania
Toshiba
Yamaha
2140
2162
2192
2135
2108
2080
2103
2054, 2055, 2056,
2057
2107, 2115, 2141,
2188
2121
2037, 2038, 2039,
2041, 2042, 2043,
2089, 2104, 2108,
2112
2090, 2096, 2097,
2126, 2193
2067, 2113
2194
2034, 2082, 2138
2027
2139
2022, 2023, 2024,
2085, 2086, 2087,
2102, 2128, 2129,
2130
2189
2030, 2099, 2100,
2101, 2114, 2117,
2118, 2119
2106
Cable
ABC
ADB
Adelphia
3004, 3015, 3016,
3017, 3037, 3040,
3067, 3080, 3081
3070
3003
Alcatel
3066
Americast
3046
Amstrad
3048, 3068
Antronix
3019, 3020
Archer
3020
Arcon
3048
AT&T
3013
Axis
3048
Bell South
3046
Cable Vision
3014
Cabletenna
3019
Cabletime
3058
Cableview
3005
Clearmaster
3045
ClearMax
3045
Clyde Cablevision
3059
Colour Voice 3022
Comcast
3006, 3010, 3039
Comcrypt
3057
Comtronics
3023
Contec
3024
Coolmax
3045
COX
3006
Cryptovision
3060
Director
3006
Eastern
3025
Everquest
3041
Fidelity
3048
Filmnet
3057
Filmnet Cablecrypt
3061
Filmnet Comcrypt
3061
Finlux
3051
Focus
3044
Foxtel
3068
France Telecom 3054, 3055
Freebox
3069
GC Electronics 3020
GE
3015, 3016
GEC
3059
Gemini
3026, 3041
General Instrument
3006, 3008, 3016,
3039, 3050, 3067,
3075
Goldstar
3042
Gooding
3049
Grundig
3048, 3049
Hamlin
3027, 3028
Hirschmann
3051
Hitachi
3016
HomeChoice 3056
Humax
3001, 3002, 3071
ITT Nokia
3051
Jasco
3041
Jerrold
3006, 3008, 3016,
3026, 3037, 3041,
3050, 3064, 3067,
3075
JVC
3049
Kabel Deutschland
3043, 3073, 3074
Macab
3055
Magnavox
3029
Maspro
3049
Matsui
3049
MegaCable
3039
Memorex
3030, 3040
Minerva
3049
Mnet
3057
Motorola
3006, 3008, 3010,
3013, 3039, 3072,
3075
Movie Time
Mr Zapp
Multichoice
Multitech
NEC
NET Brazil
Nokia
Noos
NSC
Oak
Pace
Palladium
Panasonic
Paragon
Philips
3031, 3063
3055
3057
3045
3018
3007
3051
3055
3031
3024
3011, 3043, 3084
3049
3034, 3036, 3040
3040
3021, 3022, 3029,
3049, 3053, 3054,
3055
Pioneer
3012, 3032, 3038,
3042, 3048, 3083,
3084
Popular Mechanics
3044
Proscan
3015, 3016
Pulsar
3040
PVP Stereo Visual Matrix
3064
Quasar
3040
RadioShack
3041, 3045
RCA
3005, 3036, 3076,
3077
Realistic
3020
Recoton
3044
Regal
3028
Regency
3025
Rembrandt
3016
Runco
3040
Sagem
3055
Samsung
3011, 3023, 3032,
3042
SAT
3048
Scientific Atlanta 3003, 3004, 3011,
3012, 3013, 3062,
3078, 3079, 3080,
3081, 3082, 3083,
3084
Signal
3026, 3041
Signature
3016
Sony
3014, 3047
Sprucer
3036
Standard Component
3033
Starcom
3026, 3037, 3041,
3067
Stargate
3026, 3041
Starquest
3026, 3041
Supercable
3008
Supermax
3045
Tele+1
3057, 3061
Telepiu
3057
Thomson
3000, 3009
TIME WARNER 3006
Tocom
3017
Torx
3067
Toshiba
3040
Tristar
3045
Tudi
3052
Tusa
3026, 3041
TV86
3031
Unika
3019, 3020
United Cable 3037, 3064
Universal
3019, 3020
Universum
3049, 3051
V2
3045
Videoway
3065
View Star
3024, 3029, 3031
vii
Viewmaster
Vision
Visiopass
Vortex View
Wittenberg
Zenith
Zentek
3045
3045
3051, 3054, 3055
3045
3048
3035, 3040, 3046
3044
Sattelite
AB Sat
AccessHD
ADB
AGS
Akai
Alba
4138, 4139
4058
4142
4138
4101, 4103
4083, 4084, 4085,
4086, 4108, 4139
Aldes
4085, 4087, 4088
Allsat
4098, 4101, 4103
Allsonic
4074, 4087, 4090
Alltech
4139
Alpha
4103
Alpha Digital 4058
Alphastar
4031
Amitronica
4139
Amstrad
4089, 4113, 4136,
4139
Anglo
4139
Ankaro
4074, 4087, 4090,
4139
Anttron
4083, 4086
Apollo
4083
Armstrong
4089, 4103
Artec
4054
Asat
4101, 4103
ASLF
4139
Astacom
4138
Astra
4089, 4091, 4100,
4137, 4139
Astro
4074, 4086, 4088,
4090, 4093, 4135,
4136, 4137
AudioTon
4086, 4098
Aurora
4140
Austar
4140
Axiel
4138
Axis
4074, 4090, 4091,
4096
Best
4074, 4090
Blaupunkt
4093
Blue Sky
4139
Boca
4089, 4100, 4105,
4139
Boston
4138
Brain Wave
4095
Broadcast
4094
Broco
4139
BSkyB
4113, 4123
BT
4138
Bubu Sat
4139
Bush
4084, 4127
Cambridge
4136
Canal Satellite 4135
Canal+
4135
CaptiveWorks 4049
Channel Master 4060, 4085
Chaparral
4025
CHEROKEE 4138
Chess
4134, 4139
CityCom
4084, 4133, 4137
Clatronic
4095
CNT
4088
Comag
4000, 4001, 4002,
4003, 4004
Commlink
4087
Comtech
4096
viii
Condor
Connexions
Conrad
4074, 4090, 4137
4074, 4092
4074, 4133, 4136,
4137
Conrad Electronic 4137, 4139
Contec
4096
Coolsat
4050
Cosat
4098
Coship
4063
Crown
4089
Daeryung
4092
Daewoo
4107, 4139
DDC
4085
Delega
4085
Dew
4096
Diamond
4097
Digiality
4137
Digital Stream 4059
DIRECTV
4017, 4018, 4020,
4021, 4022, 4024,
4037, 4038, 4040,
4041, 4043, 4045,
4057, 4106, 4143,
4144, 4145, 4146,
4147, 4148, 4149,
4150, 4151, 4152,
4153, 4154, 4155,
4156, 4157
Discoverer
4134
Discovery
4138
Diseqc
4138
Dish Network 4011, 4012, 4013,
4014, 4019, 4039,
4064
Dishpro
4039, 4064
Distrisat
4103
Ditristrad
4098
DNT
4092, 4101, 4103
Drake
4026
DStv
4140
Dune
4074
Echostar
4011, 4019, 4039,
4064, 4092, 4139
Einhell
4083, 4087, 4089,
4136, 4139
Elap
4138, 4139
Elekta
4088
Elsat
4139
Elta
4074, 4083, 4090,
4098, 4101, 4103
Emanon
4083
Emme Esse
4074, 4090
Engel
4139
Ep Sat
4084
EURIEULT
4077
Eurodec
4102
Europa
4103, 4136, 4137
Europhon
4137
Eurosat
4089
Eurosky
4074, 4089, 4090,
4133, 4136, 4137
Eurostar
4089, 4133, 4137
Eutelsat
4139
Exator
4083, 4086
Expressvu
4039
Fenner
4074, 4134, 4139
Ferguson
4084, 4102, 4132
Fidelity
4136
Finlandia
4084
Finlux
4084
FinnSat
4096, 4102
Flair Mate
4139
Foxtel
4140
Freecom
4083, 4099, 4136
FTEmaximal 4074, 4139
Fuba
4074, 4083, 4090,
4092, 4093, 4101,
4133
Galaxis
4074, 4087, 4090,
4091, 4096, 4098,
4133, 4140
GE
4015, 4016, 4061,
4151
General Instrument
4027, 4065
GMI
4089
GOI
4039
Goldbox
4135
GoldStar
4099
Goodmans
4079, 4080, 4084
Goodmind
4061
Grandin
4077
Grothusen
4083, 4099
Grundig
4084, 4086, 4093,
4113, 4129, 4136,
4140
Hänsel & Gretel 4137
Hantor
4083, 4095
Hanuri
4088
Hauppauge
4126
Heliocom
4137
Helium
4137
Hinari
4085
Hirschmann
4074, 4093, 4128,
4136, 4137, 4138
Hisawa
4095
Hisense
4066
Hitachi
4032, 4084, 4149,
4153
Homecast
4005, 4006, 4007
Houston
4098
HTS
4039
Hughes
4018, 4022, 4144,
4146, 4150, 4152
Hughes Network Systems
4021
Humax
4051, 4075, 4076,
4110
Huth
4087, 4089, 4094,
4095, 4096, 4098,
4137, 4141
Hypson
4077
Ilo
4066
Imex
4077
Innovation
4090
Insignia
4057
Intertronic
4089
Intervision
4098, 4137
ITT Nokia
4084
Jerrold
4065
Johansson
4095
JOK
4138
JSR
4098
JVC
4011, 4019, 4039,
4079
Kamm
4139
Kathrein
4093, 4101, 4103,
4109, 4112, 4120,
4133, 4138, 4139
Kathrein Eurostar 4133
Klap
4138
Konig
4137
Kosmos
4099
KR
4086
Kreiselmeyer 4093
K-SAT
4139
Kyostar
4083
L&S Electronic 4074
Lasat
4074, 4088, 4090,
4100, 4133, 4134,
4137
Lasonic
4062
Lenco
4074, 4083, 4099,
4133, 4137, 4139
Leng
4095
Lennox
4098
Lenson
4136
Lexus
4103
LG
4053, 4057, 4099
Lifesat
4074, 4090, 4134,
4139
Lifetec
4090
Lorenzen
4137
Lorraine
4099
Lupus
4074, 4090
Luxor
4136
Lyonnaise
4102
Macab
4102
Magnavox
4045, 4055
Manata
4077, 4138, 4139
Manhattan
4084, 4088, 4098,
4138
Marantz
4101
Mascom
4088
Maspro
4084, 4139
Matsui
4138
Max
4137
Mediabox
4135
Mediamarkt
4089
Mediasat
4091, 4135, 4136
Medion
4074, 4090, 4139
Medison
4139
Mega
4101, 4103
Memorex
4045
Metronic
4077, 4078, 4083,
4086, 4087, 4088,
4139
Metz
4093
Micro electronic 4136, 4137, 4139
Micro Technology 4139
MicroGem
4056
Micromaxx
4074, 4090
Microstar
4090
Microtec
4139
Minerva
4093
Mitsubishi
4084, 4093, 4152
Mitsumi
4100
Morgan’s
4089, 4100, 4101,
4103, 4139
Motorola
4008, 4009, 4010,
4065
Multichoice
4140
Multitec
4134
Muratto
4099
Mysat
4139
Navex
4095
Neuhaus
4091, 4098, 4136,
4137, 4139
Neusat
4139
Next Level
4065
NextWave
4141
Nikko
4089, 4139
Nokia
4084, 4122
Nordmende
4083, 4084, 4085,
4088, 4102
Nova
4140
Novis
4095
Oceanic
4097
Octagon
4083, 4086, 4096
Okano
4089
Optex
4098
Optus
4135, 4140, 4141
Orbitech
OSat
Otto Versand
Pace
Pacific
Packsat
Palcom
Palladium
Palsat
Panasat
Panasonic
Panda
Pansat
Patriot
Paysat
PCT
Philco
Philips
Phoenix
Phonotrend
Pioneer
Polsat
Predki
Premiere
Priesner
Primestar
Profile
Promax
Prosat
Proscan
Protek
Proton
Provision
Quadral
Quelle
Quiero
RadioShack
Radiola
Radix
Rainbow
RCA
Realistic
Redpoint
Redstar
RFT
Roadstar
Roch
Rover
Saba
Sabre
Sagem
Sakura
Samsung
SAT
Sat Cruiser
Sat Partner
Sat Team
4083, 4134, 4135,
4136
4086
4093
4084, 4093, 4113,
4121, 4125, 4138
4097
4138
4085
4089, 4136
4134, 4136
4140
4043, 4044, 4046,
4084, 4113, 4118,
4143, 4148
4084, 4137
4047
4138
4045
4060
4055
4021, 4022, 4045,
4084, 4101, 4103,
4111, 4115, 4135,
4138, 4150, 4152,
4153, 4155, 4156
4096
4084, 4087, 4098
4124, 4135
4102
4095
4098, 4135
4089
4030
4138
4084
4085, 4087
4015, 4016, 4040,
4151
4097
4066
4088
4074, 4085, 4087,
4090, 4138
4093, 4133, 4137
4102
4065
4101, 4103
4092, 4119
4086
4015, 4016, 4034,
4035, 4036, 4037,
4038, 4040, 4151,
4157
4028
4091
4074, 4090
4087, 4101, 4103
4139
4077
4074, 4139
4088, 4133, 4137,
4138
4084
4069, 4102
4096
4018, 4021, 4023,
4041, 4042, 4081,
4082, 4083, 4114,
4150, 4154
4085, 4136
4141
4083, 4086, 4088,
4095, 4099, 4136
4139
Satcom
Satec
Satelco
Satford
Satmaster
Satplus
Schneider
Schwaiger
SCS
Seemann
SEG
4094, 4137
4139
4074
4094
4094
4134
4090, 4134, 4138
4097, 4134, 4137
4133
4089, 4091, 4092
4074, 4083, 4090,
4095
Seleco
4098
Servi Sat
4077, 4139
Siemens
4093
Silva
4099
Skantin
4139
Skardin
4091
Skinsat
4136
SKR
4139
Skymaster
4067, 4068, 4087,
4134, 4139
Skymax
4101, 4103
SkySat
4134, 4136, 4137,
4139
Skyvision
4098
SM Electronic 4134, 4139
Smart
4133, 4139
Sony
4017, 4020, 4135
SR
4089, 4100
Star Choice
4065
Starland
4139
Starring
4095
Start Trak
4083
Strong
4074, 4083, 4086,
4090, 4099, 4140
STS
4033
STVI
4077
Sumida
4089
Sunny Sound 4074
Sunsat
4139
Sunstar
4074, 4089, 4100
Supermax
4141
Tandberg
4102
Tandy
4086
Tantec
4084
TCM
4090
Techniland
4094
TechniSat
4071, 4072, 4073,
4092, 4103, 4116,
4117, 4134, 4135,
4136
Technology
4140
Technosat
4141
Technowelt
4137
Teco
4089, 4100
Telanor
4085
Telasat
4133, 4137
Telecom
4139
Telefunken
4067, 4083, 4138
Teleka
4086, 4089, 4092,
4136, 4137
Telemaster
4088
Telesat
4137
Telestar
4134, 4135, 4136
Televes
4084, 4136
Telewire
4098
Tempo
4141
Tevion
4090, 4139
Thomson
4070, 4084, 4102,
4104, 4130, 4133,
4135, 4137, 4138,
4139
Thorens
4097
Thorn
4084
Tivax
Tivo
Tokai
Tonna
Toshiba
Triad
Triasat
Triax
Turnsat
Tvonics
Twinner
UEC
Uher
UltimateTV
Uniden
Unisat
Unitor
Universum
US Digital
Variosat
Vega
Ventana
Viewsat
Visiosat
Voom
Vortec
Welltech
WeTeKom
Wevasat
Wewa
Winersat
Wisi
Woorisat
Worldsat
Xrypton
XSat
Zehnder
Zenith
Zodiac
4058
4150
4103
4084, 4094, 4098,
4136, 4139
4144, 4152, 4153
4099
4136
4093, 4133, 4136,
4139
4139
4132
4077, 4139
4140
4134
4020
4029, 4045
4089, 4096, 4103
4095
4093, 4133, 4137
4066
4093
4074
4101, 4103
4048
4095, 4098, 4138,
4139
4065
4083
4134
4134, 4136
4084
4084
4095
4084, 4092, 4093,
4136, 4137
4088
4138
4074
4139
4074, 4088, 4090,
4131, 4133
4052, 4057, 4145
4086
CD
Yamaha
5000, 5013
CD Recoder
Yamaha
5001
MD
Yamaha
5002, 5003, 5004
Tape
Yamaha
5005, 5006
Tuner
Yamaha
5007, 5008, 5009,
5010, 5014, 5015,
5016, 5017, 5018
USB
Yamaha
5012, 5021
DOCK
Yamaha
5011, 5022
LD
Yamaha
2002
ix
© 2009 Yamaha Corporation All rights reserved.
Printed in China
WQ95460
UCRTKALBGEF
RX-V565/V465
The letters in circles and the numbers in squares correspond to those in the Owner's Manual.
Les lettres dans les cercles et les numéros dans les carrés correspondent à ceux du mode d'emploi.
Die Buchstaben in Kreisen und die Nummern in Kästchen entsprechen denen in der Bedienungsanleitung.
Bokstäverna i cirklarna och siffrorna i rutorna motsvarar de i bruksanvisningen.
Le lettere cerchiate e i numeri nei quadratini corrispondono a quelli nel Manuale di istruzioni.
Las letras enmarcadas en un círculo y los números enmarcados en un cuadrado se corresponden con aquellos del manual de instrucciones.
De letters in cirkels en de nummers in hokjes corresponderen met de in de Gebruiksaanwijzing.
Буквы в кружочках и цифры в квадратиках соответствуют таковым в инструкции по эксплуатации.
圆圈内的字母和正方形内的数字与说明书内的同类字母和数字相对应。
원 안의 문자들과 사각형 안의 숫자들은 사용자 설명서에 있는 것들과 일치합니다 .
■ Front panel/Face avant/Frontblende/Frontpanelen/Pannello anteriore/Panel delantero/Voorpaneel/
Фронтальная панель/ 前部面板 / 전변 패널
U
T
D
E
F
G
H
P
VOLUME
HDMI THROUGH
INFO
l
MEMORY
PRESET
h
l
AM
FM
TUNING
h
SCENE
PHONES
TONE CONTROL
BD/DVD
TV
CD
RADIO
PROGRAM
STRAIGHT
DIRECT
INPUT
l
STANDBY
/ON
h
EFFECT
SILENT CINEMA
A
l
h
VIDEO AUX
OPTIMIZER MIC
VIDEO
B
C
J
K
LM
N
O
I
Q
AUDIO
R
PORTABLE
S
■ Remote control/Boîtier de télécommande/Fernbedienung/Fjärrkontrollen/
Telecomando/Mando a distancia/Afstandsbediening/Пульт ДУ/ 遥控器 / 리모콘
a
b
CODE SET
TRANSMIT
c
d
POWER
SOURCE
POWER
SLEEP
e
HDMI
1
2
3
4
3
4
f
AV
1
g
2
AUDIO
5
6
1
2
V-AUX
[ A ]
[ B ]
DOCK
PRESET
TUNING
TUNER
h
FM
AM
i
INFO
MEMORY
MOVIE
MUSIC
ENHANCER SUR. DECODE
j
STEREO
STRAIGHT
DIRECT
SCENE
k
l
BD
DVD
TV
CD
SETUP
n
o
VOLUME
ENTER
DISPLAY
TOP
MENU
s
m
OPTION
RETURN
r
RADIO
MENU
MUTE
q
p
REC
1
2
3
4
5
6
7
8
9
0
10
ENT
TV
INPUT
t
POWER
TV VOL
TV CH
MUTE
Printed in China
WQ95580
U
RX-V665/RX-V565/RX-V465
English
Additional information
About the HDMI control function
This unit supports the HDMI control function.
When a TV that supports the HDMI control function is
connected with this unit via the HDMI connection, the
following operations of this unit can be controlled with the
TV remote control (except for some TVs).
• Switching between on and standby (linked to the TV)
• Volume control (up/down, mute)
• Switching the sound output between a TV and this unit.
1
Connect a TV that supports the HDMI control
function to this unit via the HDMI connection.
2
Turn on all components connected to this
unit via the HDMI connection.
For details on operations of external components,
refer to their operating instructions.
3
Check the settings of those components and
enable the HDMI control function.
Bring up to setup menu, and set “Control” to “On.”
For details on settings of the external components,
refer to their operating instructions.
y
• If you connect this unit to an HDMI control-compatible DVD player or
Blu-ray Disc player via HDMI, you can also control the connected
component in synchronization with this unit (except some models).
y
You can turn on or off the HDMI control function from the
following setup menu item.
Setup menu
Function Setup → 1 HDMI → Control
• You do not need to do step 1 through 3 from the second time.
4
Turn off the TV.
5
Check if all components connected via the
HDMI connection except for the TV are
turned on.
If they are turned off, turn them on.
6
Turn on the TV.
7
Set the input of the TV according to the
component connected to this unit such as
[HDMI].
8
Set the input of this unit to the DVD recorder
or Blu-ray recorder, and check if images from
the recorder appear normal.
9
Perform operations with the TV remote
control, such as switching this unit between
on and standby, adjusting the volume and
switching the sound output components.
Control
Choices:
On/Off*
Selects on or off of HDMI control function when a
component that supports the HDMI control function is
connected with this unit.
On
Off
Enables the HDMI control function.
Disables the HDMI control function.
y
• When the HDMI control function is enabled, display of the following
items in “1 HDMI” of the setup menu turns off.
– Standby Through
– Audio Output
• During standby, the HDMI THROUGH indicator on the front panel
display lights up under the following conditions:
– the HDMI control function is enabled
– An HDMI signal input to this unit passes through this unit and output.
See “Standby Through” or “Standby” (Setup menu → Function setup
→ 1 HDMI) on the manual for the details on the pass-through output of
an HDMI signal.
• While this unit is on standby with the HDMI control turned on, it
consumes 1 to 3W of power depending on a condition of an HDMI signal
passing through this unit.
Using the HDMI control function
When you use the HDMI control function, do the
following referring to the operating instructions of the TV.
• Turn on the HDMI control function on the TV.
• Connect the TV to this unit following the instructions
for connecting the TV to an AV amplifier.
y
• The HDMI control-compatible components include Panasonic VIERA
Link compatible TV, DVD player/recorder and Blu-ray Disc player.
• When a DVD recorder/Blu-ray recorder/HD DVD recorder that supports
the HDMI control function is connected via the HDMI connection, its
operations are also linked to those of this unit. For details, refer to its
operating instructions.
• We recommend that you use a TV, DVD recorder, Blu-ray recorder and
HD DVD recorder of the same manufacturer.
© 2009
All rights reserved.
y
• If this unit does not work, check the following. It may also work
normally after turning it off and back on or unplugging it and plugging it
back in.
– “Control” is set to “On.”
– The HDMI control function is enabled in the TV settings (refer to the
operating instructions of the TV).
Note
• If your monitor supports the HDMI control function, the scene of this
unit is automatically set to “TV” according to switching of input on the
monitor when the HDMI control function of this unit and the monitor are
turned on. AV1 input is assigned to “TV” by default. By connecting an
audio output terminal of the monitor to an optical digital terminal of
AV1, you can watch a movie or a TV program right away. When the
audio output of the monitor is connected to AV2-6, AUDIO1-2, and VAUX assign the input source for that terminal to “TV” with the SCENE
function.
Printed in China
WR87570
01EN_RX-V665_565_465_AddSheet_Flyer.fm Page 1 Thursday, April 30, 2009 5:22 PM
English
UCRABGLEF
RX-V665/V565/V465
Additional information for audio/video connection
When AUDIO1 or AUDIO2 is selected as the input
source, an analog video signal input from an external
component connected to the AV1-6 or V-AUX jack can be
output to the video monitor. For example, you can use this
connection for an external component whose audio output
is an analog signal and outputs a video signal via
component jacks, such as a game console.
To connect such a component, do the following
connection/setting.
Part 1: Connecting an external component
Part 2: Assigning the video input jacks to the audio input
Example of connection
External component
(such as game console)
Video output
Audio output
(BD/DVD)
DOCK
H
HDMI 1
HDMI OUT
ANTENNA
COMPONENT
VIDEO
COMPONENT
VIDEO
UNBAL.
PR
PR
PB
PB
PR
FM
GND AM
PB
VID
VIDEO
Y
Y
Y
Part 1: Connecting an external
component
MONITOR OU
L
R
• Audio output jacks: Connect the audio output jacks of
the external component to the AUDIO1 or AUDIO2
audio input jacks.
• Video output jacks: Connect the video output jacks of
the external component to the AV1-6 or VIDEO AUX
video input jacks.
OPTICAL
COAXIAL
COAXIAL
AV 2
AV 3
( TV )
AV 1
OPTICAL
(CD)
AV 4
AV 5
AV 6
AV
OUT
AUDIO1
AUDIO2
(RX-V665 U.S.A.model)
Part 2: Assigning the video input
jacks to the audio input
Note
• Make sure that this unit and other components are unplugged from the
AC wall outlets.
1
Turn on this unit.
■
2
Press AUDIO1 or AUDIO2 on the remote
control to select the input source.
3
Press OPTION on the remote control.
The OPTION menu appears.
4
Press Cursor k / n to display “Video Out,”
and press ENTER.
5
Audio connection
Output jacks on the
connected source
component
Analog audio output
■
Input sources/jacks of this unit
AUDIO1
AUDIO
AUDIO2
AUDIO
Video connection
AV3 (CD)
VIDEO
Press Cursor l / h to select the video input
terminal connected to the video output jacks
of the external component.
• AV1-2 (COMPONENT VIDEO)
• AV3-6 (VIDEO)
• AV5 (S-VIDEO)*
• V-AUX (VIDEO)
• Off (no video input)
AV4
VIDEO
* Some models only.
AV5
VIDEO
AV6
VIDEO
VIDEO AUX
(Front panel)
VIDEO
Output jacks on the
connected source
component
Component video output
Composite video output
S-Video output
Jacks of this unit
AV1 (TV)
COMPONENT
VIDEO
AV2
COMPONENT
VIDEO
AV5
6
To end the setting, press OPTION.
S-VIDEO*
* Some models only.
Note
• If the video monitor is connected to this unit via an analog video
connection (component video or composite video connection), connect
the external component to this unit via the same analog connection.
© 2009 Yamaha Corporation All rights reserved.
Printed in China
WT51530

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement