Viking | VWH3610SS | Installation Instructions (1 MB) | Viking VWH3010SS Installation Instructions (1 MB)

Installation Guide
Professional Built-in
Hoods
Table of Contents
Warnings & Important Information _________________________________________________________ 3
VWH 10”H. Wall Hoods w/Standard Ventilator 30”, & 36”
Dimensions & Specifications _____________________________________________________ 5
Clearance Dimensions ___________________________________________________________ 6
Interior Ventilator Dimensions ____________________________________________________ 7
Planning Information _________________________________________________________________ 8
Installation Procedures
Installation (VWH 10”H. Wall Hoods w/Standard Ventilator) ___________________________ 9
Duct Cover Option (VWH 10”H. Wall Hoods w/Standard Ventilator)___________________ 11
Installation (VWH 10”H. Wall Hoods w/Recirculating Kit) _____________________________ 11
Service & Registration_______________________________________________________________ 15
2
IMPORTANT–Please Read and Follow!
NOTE: If installing hood with warming shelf panel,
install warming shelf panel first.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
1. Installation work and electrical wiring must
be done by qualified person(s) in
accordance with all applicable codes and
standards, including fire-rated construction.
2. Sufficient air is needed for proper
combustion and exhausting of gases
through the flute (chimney) of fuel burning
equipment to prevent back drafting. Follow
the heating equipment manufacturer’s
guideline and safety standards such as
those published by the National Fire
Protection Association (NFPA), and the
American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE),
and the local code authorities.
3. When cutting of drilling into wall or ceiling,
do not damage electrical wiring and other
hidden utilities.
4. Ducted fans must always be vented to the
outdoors.
5. WARNING!: To reduce risk of fire, use only
metal ductwork
6. CAUTION!: To reduce risk of fire and to
properly exhaust air, be sure to duct air
outside. Do not vent exhaust air into
spaces within walls or ceilings, or into
attics, crawl spaces, or garages.
7. CAUTION!: To Reduce the Risk of Fire and
Electric Shock, Install this rangehood only
with remote blower models manufactured
by Viking, model numbers –
DEV900/DEV1200, VEV900/VIL1200, OR
integral blowers manufactured by Viking
Range, model numbers –
VINV300/600/1200, or DIL1200. NOTE –
Please refer inside for specific
canopy/blower combinations.
IMPORTANT – PLEASE READ AND FOLLOW
• Before beginning, please read these instructions
completely and carefully.
• Do not remove permanently affixed labels,
warnings, or plates from the product. This may
void the warranty.
• Please observe all local and national codes and
ordinances. If no local codes are applicable, wire
in accordance with the National Electrical Code,
ANSI/NFPA 70-latest edition.
• Damp environment approved models should be
installed in a covered non-enclosed area and
should be protected from the elements as much
as possible.
• The installer should leave these instructions with
the consumer who should retain for local
inspector’s use and for future reference.
• Check with a qualified and trained installer or local
codes for makeup air requirement, if any.
This hood is for residential installation only and is
not designed for installation over a commercial
product. Make sure power is off at the main circuit
breaker or fuse box before making connections. To
avoid risk of fire, electric shock, or injury to persons,
turn off the electricity to the hood from the power
supply before servicing or cleaning. Our hoods are
equipped with variable speed control blowers.
These units will not function with a single speed
ventilator. All Viking Range ventilator kits are
designed specifically for use with Viking Range
hoods. Use of any non-Viking Range ventilator kit
will void the hood warranty.
READ AND SAVE THESE INSTRUCTIONS
3
IMPORTANT–Please Read and Follow!
WARNING
WARNING
To reduce the risk of injury to persons in
the event of a rangetop grease fire,
observe the following. (Based on “Kitchen
Firesafety Tips,” published by NFPA.)
To reduce the risk of fire, electric shock, or
injury to persons, observe the following:
• Use this unit only in the manner intended by
the manufacturer. If you have any questions,
contact the manufacturer.
• Before servicing or cleaning unit, switch
power off at service panel and lock service
panel to prevent power from being switched
on accidentally. When the service
disconnecting means cannot be locked,
securely fasten a prominent warning device,
such as a tag, to the service panel.
1. SMOTHER FLAMES with a close fitted lid,
cookie sheet, or metal tray, then turn off the
burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE
DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN. You may
be burned.
3. DO NOT USE WATER, including wet
dishcloths or towels a violent steam
explosion will result.
4. Use an extinguisher ONLY if
• You know it is a Class ABC extinguisher,
and you already know how to operate it.
• The fire is small and contained in the area
where it started.
• The fire department is being called.
• You can fight the fire with your back to an
exit.
CAUTION
For general ventilating use only. Do not use to
exhaust hazardous or explosive materials and
vapors.
WARNING
TO REDUCE THE RISK OF
FIRE, ELECTRICAL SHOCK, OR
INJURY
TO PERSONS
Rangehoods must be installed
with the ventilators that are
specified on their carton
indicating suitability with this model. Other
ventilators cannot be substituted.
4
Dimensions & Specifications
(VWH 10”H. Wall Hoods w/Standard Ventilator 30”, & 36”)
1
(30 2 ”
.5
cm
)
(7. 3”
6c
m
)
1
(25 0 ”
.4
cm
)
A (Hood width)
30”W.
29-7/8“ (76.2 cm)
36”W.
35-7/8” (91.1 cm)
”
21 cm)
A
.3
(53
NOTE: Optional duct cover sold separately.
VWH 10”H. Wall Hoods w/Standard Ventilator
Description
30”
36”
29-7/8” (75.9 cm)
Duct cover width
35-7/8” (91.1 cm)
Duct cover depth
12” (30.5 cm)
Duct cover height
12” (30.5 cm)
Number of lights
2
2
Number of filters
N/A
Heat lamps
7” (17.8 cm)
Interior duct size*
5.6
Interior—Maximum amps
* Disregard when using recirculating kits. Blower is shipped with hood.
Interior
Ventilator
Standard
Models
“L”
Models
“M”
Models
CFM
460
390
300
5
Clearance Dimensions
(VWH 10”H. Wall Hoods w/Standard Ventilator)
60
24
(15 ”m
2.4 in.
c
63 to m)
”
(16 ma
0.0 x.
cm
)
(61”min
.0 .
c
27 to m)
”m
(68 ax
.6 .*
cm
)
”
36 cm)
.4
(91
* NOTE: When installing with a 24” high-shelf,
the 27” (68.6 cm) max. dimensions must be used.
6
Interior Ventilator Dimensions
(VWH 10”H. Wall Hoods w/Standard Ventilator)
Top View
30”W.
36”W.
A
29-7/8” (75.9 cm)
35-7/8” (91.1 cm)
A
18”
(4.6 cm)
B
30”W.
36”W.
B
8-1/4” (20.9 cm)
11-1/4” (28.6 cm)
30”W.
36”W.
C
14-15/16” (37.9 cm)
17-15/16” (45.6 cm)
30”W.
36”W.
D
3-5/8” (9.2 cm)
6-5/8” (16.8 cm)
D
3-4”
(1.9 cm)
C
4”
(10.2 cm)
3-7/8”
(9.8 cm)
7” (17.8 cm) dia.
duct location
Interior Ventilator Installation
7
1/2”
(1.3 cm)
3-1/2”
(8.9 cm)
Electrical
hookup
Planning Information
Proper installation of ducting is extremely
important to ensure maximum performance
from any ventilation product.
• All CFMs are based on tests at 0.1 static
pressure: without applying static pressure, CFM
would be greatly overstated.
• Straight runs and gradual turns are best; for
example, each 90º elbow is equivalent to 5-10
feet (1.52-3.05 cm) of straight run.
• Never use flexible duct; it creates back pressure/air
turbulence and greatly reduces performance.
• Proper performance is dependent on proper
ducting; make sure that a qualified and trained
installer is used.
• Check with a qualified and trained installer or
local codes for makeup air requirement, if any.
• Max. amp rating for hoods includes
recommended ventilator kit rating; all products
must be hard wired direct with 2-wire with ground.
Roof cap
Interior-power
typical ductwork
7” round duct
Duct cover or soffit
Hood
Wall Installation
typical ductwork
Wall cap
Plan where the duct work will be located. Install
proper-sized duct work, and roof or wall cap for the
type of blower you are using. Recommended hood
locations for the most common installations are
shown. Adjust your measurements for various heights
of ceilings, soffits, cabinets, or ranges/rangetops.
Duct
Duct cover or soffit
Hood
Check Framing
NOTE: Wall exhaust must be a minimum of 24” (61.0 cm)
from ground. This may vary depending on local codes
and geographic location.
NOTE: Because of the weight of the hood make sure
that the mounting screws are driven into the framing
and not just the drywall. It may be necessary to drill
additional holes in the canopy for proper alignment.
8
Installation (VWH 10”H. Wall Hoods w/Standard Ventilator)
2
1
Check damper for unrestricted movement, adjust if
necessary.
Attach transition to damper. Seal with aluminum tape.
3
WARNING
To reduce the risk of fire, electric shock, or injury
to persons, observe the following:
• Use this unit only in the manner intended by the
manufacturer. If you have any questions, contact
the manufacturer.
• Before servicing or cleaning unit, switch power off
at service panel and lock service panel to prevent
power from being switched on accidentally. When
the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such
as a tag, to the service panel.
Flip hood over and remove electrical box cover.
5
4
1
2
1
Insert 6” of electrical wiring through the top of vent hood
and secure using wiring restrain. Refer to local codes.
Slide duct over transition and tape around joint.
9
6
5/16”
nut driver
5/16”
nut driver
CAUTION: Secure vent hood to wall
using screws provided. Use additional mounting screws
and wall anchors, if necessary.
7
CAUTION: If not using a duct cover, using
screws provided, make sure top mounting screws are secured
into soffit or cabinet framing. Use additional mounting screws,
if necessary.
8
BARE OR GREEN
1
1
2
GREEN
BLACK
WHITE
BLACK
WHITE
Connect black to black, white to white, and the
green/bare wire under the green screw.
NOTE: Housing wiring must be properly installed for
wiring to be correct when wiring unit.
Replace electrical box cover. Make connection to
breaker box.
9
10
1
1
1
1
2
3
3
2
2
Slide filter front over front lip. Push filter rear up, then
slide back over rear lip.
Slide spacer front over front lip. Push spacer rear up,
then slide back over rear lip.
10
11
1
3
2
Slide filter front over front lip. Push filter
rear up, then slide back over rear lip.
Duct Cover Option
(VWH 10”H. Wall Hoods w/Standard Ventilator)
1
2
Measure distance from ceiling to canopy.
Installation
2
Slide the duct cover in place and fasten from inside
canopy using the sheet metal screws provided.
(VWH 10”H. Wall Hoods w/Recirculating Kit)
1
2
Remove damper and discard with transition.
Turn recirculating unit upside down. Place vent hood
upside down on recirculating unit.
11
3
4
Attach with screws and lock washers provided.
Attach with screws.
WARNING
5
To reduce the risk of fire, electric shock, or injury
to persons, observe the following:
• Use this unit only in the manner intended by the
manufacturer. If you have any questions, contact
the manufacturer.
• Before servicing or cleaning unit, switch power off
at service panel and lock service panel to prevent
power from being switched on accidentally. When
the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such
as a tag, to the service panel.
Remove electrical box cover.
6
7
1
5/16”
nut driver
2
Flip hood over. Insert 6” of electrical wiring through the top
of vent hood and secure. Refer to local codes.
12
CAUTION: Secure vent hood. Make sure
mounting screws are secured into framing. Use additional
mounting screws and wall anchors, if necessary.
8
9
BARE OR GREEN
1
1
2
GREEN
BLACK
WHITE
BLACK
WHITE
Connect black to black, white to white, and the
green/bare wire under the green screw.
NOTE: Housing wiring must be properly installed for
wiring to be correct when wiring unit.
Replace electrical box cover. Make connection to
breaker box.
10
11
1
2
3
Slide filter front over front lip. Push filter rear up, then
slide back over rear lip.
Assemble brackets to baffles and insert charcoal filters.
13
12
1
1
2
3
3
2
Slide filter front over front lip. Push filter rear up, then
slide back over rear lip.
Slide spacer front over front lip. Push spacer rear up,
then slide back over rear lip.
13
Service & Registration
If service is required, call your dealer or authorized service agency.
The name of the authorized service agency can be obtained from the dealer or distributor in your area.
Have the following information readily available.
• Model number
• Serial number
• Date purchased
• Name of dealer from whom purchased
Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized
service agency, or if you continue to have service problems, contact Viking Range, LLC at1-888-(845-4641),
or write to:
VIKING RANGE, LLC
PREFERRED SERVICE
111 Front Street
Greenwood, Mississippi 38930 USA
Record the information indicated below. You will need it if service is ever required. The model and serial
number for your hood is located behind the baffle filter on the left side panel in the lower right corner.
Model no. ______________________________________________ Serial no. __________________________________________________________
Date of purchase ______________________________________ Date installed ____________________________________________________
Dealer’s name __________________________________________________________________________________________________________________
Address __________________________________________________________________________________________________________________________
____________________________________________________________________________________________________________________________________
If service requires installation of parts, use only authorized parts to ensure protection under the warranty.
THIS MANUAL SHOULD REMAIN WITH THE HOOD FOR FUTURE REFERENCE.
14
15
Viking Range, LLC
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-(845-4641)
or visit our web site at vikingrange.com in the US
or brigade.ca in Canada
F21455 EN
(013015)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising