Viking | VDWU524SS | Installation guide | Viking VDWU524SS Installation Guide

Viking VDWU524SS Installation Guide
Installation
GUIDE
VDWU524SS
VDWU524WSSS
FDWU524WS
FDWU524
VDWU324SS
FDWU324
To prevent accidents, which could cause serious injury or death, as well as
machine damage read these instructions before installation and / or use.
INTRODUCTION
1
1. IMPORTANT SAFETY INSTRUCTIONS
1
1.1 INSPECT THE DISHWASHER
2
2. TOOLS WHICH MAY BE NEEDED
3
3. MATERIALS WHICH MAY BE NEEDED
3
4. MATERIALS SUPPLIED
4
4.1 PARTS SUPPLIED
4.2 MANUAL BAG
4.3 DISHWASHER PARTS BAG 1
4.4 DISHWASHER PARTS BAG 2
4.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER
4
4
4
4
4
5. DISHWASHER SPECIFICATIONS
5
5.1 TECHNICAL FEATURES
5
6. ENCLOSURE PREPARATION
6
6.1 ELECTRICAL PREPARATION
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS
6.3 ADJUSTING HEIGHT
6.4 INSTALLING THE SIDE TRIM STRIPS
6.5 PREPARING THE WATER CONNECTION (A)
6.6 DRAIN PREPARATION
6.7 STEAM PROTECTION FOIL
6
6
9
9
10
10
12
7. PLACEMENT OF DISHWASHER INTO THE OPENING
12
7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS
7.2 READJUSTING FOOT LEVELS
7.3 ADJUSTING THE MOVABLE TOE KICK
7.4 FIXING THE CABINET TO THE COUNTER
7.5 PREPARING THE CUSTOM DOOR
7.6 PREPARING THE PRODUCT DOOR
7.7 INSTALLING THE CUSTOM DOOR
7.8 FIXING THE CUSTOM DOOR
7.9 FIXING THE CUSTOM DOOR
7.10 ADJUSTING THE KICK PLATE
7.11 CONNECTION
12
14
14
16
17
18
19
19
20
20
21
8. INSTALLER CHECKLIST
23
9. SELF HELP HINTS:
23
user.
INTRODUCTION
WARNING
Please read this installation manual
and particularly the safety instructions
completely and carefully. They will save you
time and effort and help to ensure optimum
dishwasher performance.
When installing the dishwasher, follow
basic precautions, including the
following:
• The dishwasher could only be converted
from cord-connected to permanently
connected by an authorized service
representative. (If needed contact your
dealer to schedule an authorized service
agent for conversion with an appropriate
conversion kit)
• Installation and repair should be
performed by a qualified installer.
Work by unqualified persons could be
dangerous and may void the warranty.
Be sure to observe all listed warnings and
cautions. Look particularly for the icons with
exclamation marks inside. The information
icon also will provide important references.
NOTICE :
WARNING:
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION:
Indicates a potentially hazardous situation
which, if not avoided, may result in injury.
It may also be used to alert against unsafe
practices.
The dishwasher should be installed by
an insured licensed plumber, contractor
or trained installer. Installation performed
by persons other than this could result in
improper installation and property damage.
• Do not operate the appliance if damaged,
malfunctioning, partially disassembled or
if it has missing or broken parts.
• Also follow the safety instructions of the
user manual.
• To reduce the risk of electric shock, fire,
or injury to persons, the installer must
ensure that the dishwasher is completely
enclosed at the time of installation.
• Only connect the dishwasher to the
power supply when all installation and
plumbing work is complete.
• If the dishwasher is installed in a location
that experiences freezing temperatures
(e.g. in a vacation home, cabin, etc.),
you must drain all the water from the
dishwasher’s interior. Water system
ruptures that occur as a result of freezing
are not covered by warranty.
• Dishwasher must be secured to adjacent
cabinetry using the brackets provided.
Failure to do this may cause damage to
property or bodily injury.
• Connect to a properly rated, protected
and sized power supply circuit to avoid
NOTICE:
Indicates a potentially hazardous situation
which, if not avoided, may result in damage
to the dishwasher, the table-ware, the
equipment or the environment.
1. IMPORTANT SAFETY
INSTRUCTIONS
In addition to these instructions, the
dishwasher shall be installed:
• In accordance with all local codes or, in
absence of a local code,
• In the United States, with the National
Electric Code,
• In Canada, with the Canadian Electric
Code C22.1-latest edition/Provincial and
Municipal codes and/or local codes.
NOTICE :
Read these installation instructions
completely before installing and follow
them carefully. Save these installation
instructions and pass them on to any future
1
USA
•
•
•
•
and replace parts as necessary.
electrical overload. The dishwasher is
designed for an electrical supply of 120 V
(volts), 60 Hz (hertz), AC, connected to a
dishwasher-dedicated, properly grounded
electrical circuit with a fuse or breakers
rated for 15 amperes. Electrical supply
conductors shall be a minimum of # 16
AWG copper wire rated at 75 °C (167
°F) or higher. These requirements must
be met to prevent injury and machine
damage. Consult a qualified electrician if
in doubt.
Do not use any extension cord or
portable outlet device to connect the
dishwasher to a power supply.
Ensure that any plastic wrappings, bags,
small pieces etc. are disposed of safely
and kept out of the reach of children.
Danger of suffocation!
Remove the door to the washing
compartment when removing an old
dishwasher from service or discarding it.
Ensure that the appliance presents no
danger to children while being stored for
disposal.
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
1.1 INSPECT THE DISHWASHER
After unpacking the dishwasher and prior
to installation, thoroughly inspect the
dishwasher for possible freight or cosmetic
damage. Report any damage immediately.
NOTICE :
• Cosmetic defects must be reported within
10 days of installation.
• Do not discard any bags or items that
come with the original package until
after the entire installation has been
completed.
NOTICE :
• The dishwasher drain hose must be
installed with a drain loop at least 28”
(710mm) off the cabinet floor; otherwise
the dishwasher may not drain properly.
• This dishwasher is intended for
residential use only, and should not be
used in commercial establishments.
• New installation - If the dishwasher is a
new installation, most of the work must
be done before the dishwasher is moved
into place.
• Replacement - If the dishwasher is
replacing another dishwasher, check
the existing dishwasher connections for
compatibility with the new dishwasher,
2
USA
2. TOOLS WHICH MAY BE NEEDED
Flat head Screwdriver
3. MATERIALS WHICH MAY BE NEEDED
(Additional materials may be required to comply with local codes)
Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided
dishwasher supply line.
Elbow with 3/4” N.P.T. female thread for dishwasher side, and sized to fit
your water supply line (copper tubing/compression fitting, or braided hose)
on the other side. Dishwasher connection is 3/4" male.
UL listed conduit connector or strain relief.
Teflon tape or other pipe thread compound to seal plumbing connections.
Shut-off valve and fittings appropriate for hot water supply line (copper
tubing/compression fitting, or braided hose).
Silicone
Glue
Dishwasher Discharge Hose Adaptor
3
USA
4. MATERIALS SUPPLIED
4.1 PARTS SUPPLIED
Parts for your dishwasher will
come in several plastic bags.
Check your parts bags shown
to make sure you have all the
parts as listed to the left.
4.2 MANUAL BAG
The dishwasher comes with a
manual bag containing:
• User manual,
• Installation manual
4.3 DISHWASHER
PARTS BAG 1
This dishwasher bag comes
with the following parts:
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
d. Screws Ø 1/8” x 5/8” (Ø
3.5 mm x 14 mm)
e. Mounting Bracket Left
f. Mounting Bracket Right
h. Screw Clamp
k. Toe Kick Bracket - Left
l. Toe Kick Bracket – Right
n. Custom Door Plug
o. Custom Door Screw
p. Toe Kick
s. Template
t. Hook and loop fastener
v. Side Door plug
z. Steam Protection Foil
x6
4
USA
4.4 DISHWASHER
PARTS BAG 2
(SELECT MODELS)
In addition to the manual bag
and the dishwasher parts bag
(dishwasher models which
can accept a wooden kitchen
door) also come with a door
panel installation kit which
contains:
y. Screws 4mm x 36 mm =
3/16th x 1-7/16th
4.5 PARTS ATTACHED
TO THE REAR OF THE
DISHWASHER
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
5. DISHWASHER SPECIFICATIONS
5.1 TECHNICAL FEATURES
Permissible water pressure
Electrical connection
Total power
Heater power
4.35 - 145 psi (0.3 - 10 bars)
120 V (volts), 12 A (amps), 60Hz (hertz)
1400 W (watts)
1100 W (watts)
NOTICE :
Because we continually strive to improve our products, we may change our specifications
and design without prior notice.
This device corresponds to the following directives:
UL 749 Household Dishwasher directive.
5
USA
6. ENCLOSURE PREPARATION
6.1 ELECTRICAL PREPARATION
WARNING
The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected
to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or
breaker rated for 15 amperes.
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS
WARNING
Dishwasher must be secured to adjacent cabinetry using the mounting brackets
provided. Failure to do this may cause damage to property or bodily injury.
d)
?
6
USA
Tighten the plugs on both sides
of your machine (v)
Place the two mounting brackets into the top
corners of the dishwasher.
Fix the mounting brackets (A) to the top corners of
the dishwasher, with the screws supplied.
Bend sides of mounting brackets (B) in order to fix
from sides (if necessary).
6.3 ADJUSTING HEIGHT
If the height of the enclosure is 33⅞” to 35⅞” (861
mm - 911mm) adjust supports as shown in the
figure.
Supplied (4)
Adjust the front foot level with the adjusting
wrench to balance and raise the dishwasher to the
enclosure height.
Adjust the rear foot level with a screwdriver to
balance and raise the dishwasher to the enclosure
height.
7
USA
NOTICE :
• Make sure the dishwasher is plumb and
notice dishwasher can be placed with a small
clearance under the counter top.
• Turning the screwdriver in the direction of the
black arrows will bring the dishwasher back
feet up.
• Turning the screwdriver in the direction of the
white arrows will take the dishwasher rear feet
down.
6.4 INSTALLING THE SIDE TRIM STRIPS
Remove the adhesive tape (Figure A).
Place the trim strips on the front edge of the side
walls (Figure B).
NOTICE :
• Make sure you use the correct trim strip since
there is a left and right side strip. The flexible
material should be facing forward (Figure B).
8
USA
6.5 PREPARING THE WATER CONNECTION (A)
Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder
connections must be made before the water line is connected to the dishwasher’s water
inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose
line.
Check with your plumbing supply sources for the proper hose and elbow and necessary
fittings for the water supply line. This material is not supplied, and must be purchased
separately.
WARNING
Installation should be performed by a qualified installer. Work by unqualified
persons could be dangerous and may void the warranty.
If the dishwasher is installed in a location that experiences freezing temperatures
(e.g. in a vacation home, cabin etc.), you must drain all the water from the
dishwasher’s interior. Water system ruptures that occur as a result of freezing are
not covered by warranty.
6.6 DRAIN PREPARATION
The dishwasher drain hose may be connected to the drain plumbing in one of three ways
(Figure A, B, C).
Water Connection
9
USA
NOTICE :
• Either one of the methods below must be used or the dishwasher will not operate
properly.
• A hose that attaches to a sink spray can burst if it is installed on the same water line as
the dishwasher. If your sink has one, it is recommended that the hose be disconnected
and the hole plugged.
• The total length of the drain hose is 763/4” (1950mm). If a hose extension is required, a
drainage hose of equal quality must be used.
• The maximum length must not exceed 157 ½” (4000mm). Otherwise, the cleaning
process is negatively influenced.
6.6.1 UNDER THE SINK DRAIN
Install a Y-branch tail pipe. (Figure A)
NOTICE :
You must add a loop at least 28” (710mm) above the floor of
the cabinet and above the drain connection in the drain hose
to prevent waste water from not draining properly, and causing
either poor washing results or a bad odor.
6.6.2 INSTALLING AN AIR GAP
If the local ordinance requires an air gap (Figure B).
NOTICE :
Check with local ordinance for type of air gap required.
6.6.3 DISPOSAL
Remove the drain connection plug before attaching the drain
hose from the dishwasher.
Every disposal has a hook up for a dishwasher; consult your
disposer manual for correct connection. (Figure C)
10
USA
6.7 STEAM PROTECTION FOIL
Steam will form inside the dishwasher during operation. At the end of the cycle, when the
dishwasher door is opened, it is required to use a steam protection foil to prevent any
steam from collecting on the underside of the counter top.
6.6.2 FITTING THE PROTECTION FOIL
Before applying the steam protection foil to the
underside of the countertop, clean the area with
a damp cloth (as shown in Figure A). Once the
area dries, apply the steam protection foil.
The steam protection
foil will be applied at the
location where the hot
steam escapes when you
first open the door (as
shown in Figure B).
CAUTION
Steam protection foil must be applied
where the steam escapes when door is
first opened. Failure to install the steam
protection foil during installation can
lead to damage to the cabinets and
countertop.
11
USA
7. PLACEMENT OF DISHWASHER INTO THE OPENING
Now place the dishwasher into the opening and get ready to connect all hoses and
electrical connections.
CAUTION
Make sure all hoses
are pulled through the
side opening of the
cabinet, no hoses are
kinked and all slack is
taken out as shown in
the figure.
7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL
CONNECTIONS
7.1.1 DRAIN HOSE CONNECTION
Connect the drain hose to the drain plumbing.
1. Use the supplied rubber connection hose and drain hose clamps to connect the
dishwasher drain hose to the plumbing drain connection.
2. Use the spring clamp to secure the rubber connection hose to the dishwasher drain
hose. Use the screw clamp to secure the rubber connection hose to the plumbing drain
connection.
Note that the marks
on the rubber
connection hose
should be on the drain
hose side
12
USA
7.1.2 WATER SUPPLY CONNECTION
Water supply may be connected to the
dishwasher in one of two ways:
• With metal braided hose.
• With copper tubing.
CAUTION
• Hot water supply line: Use minimum 3/8”
O.D. copper tubing or metal braided
dishwasher supply line.
• Temperatures required for soldering and
sweating will damage the dishwasher’s
water inlet valve so if any such operation
is needed, keep the heat source min. 7⅞”
(200mm) away from the dishwasher’s
water inlet valve.
• There should not be any sharp bends in
the water line that may restrict the water
flow.
• Teflon tape or pipe tread compound
must be used for sealing the connection.
Before connecting the copper water
supply line to the dishwasher, flush it with
hot water to clear any foreign material.
NOTICE :
After connections are made turn on the
water supply to check for leaks.
7.1.3 ELECTRICAL CONNECTION
WARNING
• Make sure the voltage and frequency
listed on the data plate correspond with
the household electrical supply. This data
must correspond to prevent injury and
machine damage. Consult a qualified
electrician if in doubt.
• Only connect the dishwasher to the main
electrical supply when all installation and
plumbing work is complete.
• Do not use any extension cord or
portable outlet device to connect the
dishwasher to a power supply.
• The power-supply receptacle for the
appliance shall be installed in a cabinet
or on a wall adjacent to the undercounter
space in which the appliance is to be
installed.
13
• The access hole of the supply cord to the
installation compartment must be smooth
and rounded and it must be large enough
for the attachment plug to pass through.
The longest dimension of the opening
shall not be more than 1½” (38 mm).If the
partition is metal, it needs to be covered
with an edge protector.
• Care must be taken when the appliance
is installed or removed, to reduce the
likelihood of damage to the power-supply
cord.
7.1.4 GROUNDING INSTRUCTIONS
This appliance must be grounded. In the
event of a malfunction or breakdown,
grounding will reduce the risk of electric
shock by providing a path of least
resistance for electric current. This
appliance is equipped with a cord having
an equipment-grounding conductor and a
grounding plug. The plug must be plugged
into an appropriate outlet that is installed
and grounded in accordance with all local
codes and ordinances. This appliance
must be connected to a grounded metal,
permanent wiring system, or an equipmentgrounding conductor must be run with the
circuit conductors and connected to the
equipment-grounding terminal or lead on
the appliance.
WARNING
Improper connection of the equipmentgrounding conductor can result in a risk
of electric shock. Check with a qualified
electrician or service representative if
you are in doubt whether the appliance is
properly grounded. Do not modify the plug
provided with the appliance, if it will not fit
the outlet, have a proper outlet installed by
a qualified electrician.
USA
7.2 READJUSTING FOOT
LEVELS
Now that the dishwasher is in the
cabinet you must readjust the feet to
bring the dishwasher up to the required
height and attach it underneath the
countertop.
1. Readjust the front foot levels with
adjusting wrench to balance the
dishwasher and raise it up under the
countertop, make sure the unit is level.
2. Readjust the rear foot levels with a
screwdriver to balance the dishwasher
and raise it to the required height using
the brackets supplied.
3. Attach the dishwasher underneath
the countertop with the four screws
supplied (Ø 1/8” x 1/8” - Ø 3.5mm
x 14mm). Make sure you do not go
through the top of the countertop or
damage granite.
7.3 ADJUSTING THE MOVABLE TOE KICK
Now that you have successfully installed the dishwasher, you
need to attach the toe kick to the dishwasher. The two piece
toe kick can be adjusted to the height and depth needed for
your kitchen. Be sure to use the slotted toe kick in the front
and the other behind it. They slide into each other.
Place parts K and L to the channel shown in Figure A for both
sides as shown in Figure B. Then fix them in the direction
shown with the arrow in Figure C and Figure B.
14
USA
Open locking tab on the Toe Kick(p). (A)
Place it on the slots, which are on the brackets
fixed before, and adjust the height - max. 1½"
(38 mm). (B)
Close locking tab on the Toe Kick. (C)
15
USA
7.4 FIXING THE CABINET TO THE COUNTER
y
16
USA
7.5 PREPARING THE CUSTOM DOOR
X
o)
X =?
s)
=
=
=
=
Mid. Point
Mid. Point
n)
t)
Height (h)
Width (w)
Thickness (t)
Weight (max)
Weight (max)
9 Kg / 19 lbs
: Height of the wooden door 30” (760mm)
: 23 ¼” to 23 ½” (592mm - 595mm)
: ¾ “ (19mm)
: 9 Kg / 19 lbs
17
USA
7.6 PREPARING THE CUSTOM DOOR
(t)
1
2
18
USA
7.7 INSTALLING THE CUSTOM DOOR
4
1
3
2
7.8 FIXING THE CUSTOM DOOR
5
34
2
1
45
3
2
1
19
USA
7.9 FIXING THE CUSTOM DOOR
(y)
Ø 4 x 36mm
12
34
5
1 23
45
7.10 ADJUSTING THE KICK PLATE
20
USA
•
Check whether the
bottom of the door (A)
hits the kitchen cabinet
base (B) .
•
If the door hits the
cabinet base cut the
necessary section out of
the base (B).
•
Apply silicone or sealant
to the cut edge of the
kitchen cabinet base
or paint so it does not
absorb moisture.
1
4
(1.9 cm)
(1.9 cm)
aǩ´ FP
aǬ´ FP
2
(1.2 cm)
(1.9 cm)
2
1
1
21
2
USA
PLQò´
FP
1
PD[´ FP
PLQ´ FP
2
PLQǩ´
FP
aǬ´ FP
PLQǩ´ FP
3
PLQ´
FP
PD[´ FP
PD[´ FP
7.11 CONNECTION
4
c
3
8. INSTALLER CHECKLIST
Your installer must have completed and
checked the following:
• The dishwasher is square and level.
• The dishwasher is fastened securely to
the cabinetry.
• The dishwasher door opens and closes
freely. The dishwasher door must close
without hitting any cabinetry or counter
top.
• The inlet water supply is turned on and
checked for leaks.
• The drain hose has been connected and
checked for leaks. There must be no
kinks or obstructions in the drain hose.
• The drain hose must be installed with a
28" (710mm) high drain loop for drain
hook-ups without any air removed.
• If the dishwasher drain is hooked up to a
garbage disposal, the drain hopper plug
must be removed.
• The spray arms are free and rotate freely.
• The rinse cycle has been run.
• The water level will be below the
filter screen after the end of the wash
program. It is normal to find some water
in the drain filter area.
Notice :
• If your dishwasher is not operating
properly after following these steps:
Contact your dealer to schedule an
authorized service agent to inspect your
new dishwasher for any function related
failure.
• The manufacturer warranty does not
cover installation, conversion or customer
education service visits.
You will find the model and serial number
information on the label located on the
right-hand side of the inner door of your
dishwasher, as shown above.
Notice :
Please make a copy of your invoice and
keep it with this manual and register your
dishwasher on-line.
9. TROUBLESHOOTING:
The screen does not come on:
• Check to make sure the breaker to the
dishwasher is in the on position.
• Check to make sure that the Supply cord
is plugged in.
No Water is coming into the dishwasher:
• Check to make sure the hot water shutoff is in the ON position.
Water does not drain:
• Make sure drain hose is not kinked or
comes out of air gap next to the sink.
• Remove drain hose from disposal making
sure plug is removed.
22
USA
SERVICE INFORMATION
If service is required, call your authorized service agency.
Have the following information readily available.
• Model number
• Serial number
• Date purchased
• Name of dealer from whom purchased
Clearly describe the problem that you are having. If you are unable to obtain the name of
an authorized service agency, or if you continue to have service problems, contact Viking
Range, LLC at 1-888-845-4641, or write to:
VIKING RANGE, LLC
PREFERRED SERVICE
111 Front Street
Greenwood, Mississippi 38930 USA
Record the information indicated below. You will need it if service is ever required. The
model and serial numbers are located on an identification label attached to the left side of
the tank. For access, simply open the door of the dishwasher.
Model no. __________________________ Serial no. ________________________
Date of purchase ____________________ Date installed _____________________
Dealer’s name _______________________________________________________
Address ____________________________________________________________
If service requires installation of parts, use only authorized parts to insure protection under
the warranty.
Keep this manual for future reference.
23
USA
Viking Range, LLC
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-845-4641
or visit our web site in the US (www.vikingrange.com)
C
068681-000 EN
068681-000 EN/ 16-07-18.(8:33)
UL US
(061518)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising