Smeg | STU1846 | User manual | Smeg STU1846 User Manual

Smeg STU1846 User Manual
INSTRUCTION MANUAL
GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS
EN
EN
EN
CONTENTS
CONTENTS
CONTENTS
Contents
Contents
Contents
1
INTRODUCTION.....................................................................................................................3
Contents
1
2
1
1
2
2
2
3
3
4
3
3
5
4
4
4
5
5
5
6
6
6
6
7
7
7
8
7
8
8
9
8
9
9
9
INTRODUCTION
DESCRIPTION
OF.....................................................................................................................3
THE CONTROLS..................................................................................5
INTRODUCTION
.....................................................................................................................3
2.1
Upper
panel
................................................................................................................5
INTRODUCTION
.....................................................................................................................3
DESCRIPTION
OF
THE
DESCRIPTION
OF washing
THE CONTROLS..................................................................................5
CONTROLS..................................................................................5
2.2 Setting the
program and switching on and off............................6
2.1
Upper
................................................................................................................5
DESCRIPTION
OFon
THE
CONTROLS..................................................................................5
2.1 Switching
Upper panel
panel
................................................................................................................5
2.2.1
...............................................................................................................9
2.2
Setting
the
washing
program
and
on
2.1 Selecting
Upper panel
................................................................................................................5
2.2
Setting
the
washing
program
and switching
switching
on and
and off
off............................6
............................6
2.2.2
and
starting
the program
................................................................
10
2.2.1
Switching
on
...............................................................................................................9
2.2 End
Setting
theon
washing
program and switching on and off............................6
2.2.1
Switching
...............................................................................................................9
2.2.3
of program
.......................................................................................................
10
2.2.2
Selecting
starting
the program
2.2.1 Interrupting
Switchingand
ona...............................................................................................................9
2.2.2
Selecting
and
starting
program ................................................................
................................................................ 10
10
8
2.2.4
programthe
........................................................................................
2.2.3
of
.......................................................................................................
10
2.2.2 End
Selecting
and
the program
................................................................ 10
9
2.2.3
End
of program
program
.......................................................................................................
2.2.5
Changing
the starting
current
program
.........................................................................
2.2.4
Interrupting
a program
........................................................................................
109
2.2.3
of program
.......................................................................................................
2.2.4
Interrupting
program
........................................................................................
2.2.6 End
Canceling
thea current
program
........................................................................ 10
11
2.2.5
Changing
the
current
program
.........................................................................
10
2.2.4
programprogram
........................................................................................
10
2.2.5
Changing
thea current
......................................................................... 11
9
2.2.7 Interrupting
Options ......................................................................................................................
2.2.6
Canceling
the current
current program
program.........................................................................
........................................................................
11
2.2.5
Changing
10
9
2.2.6 Switching
Canceling the
........................................................................ 12
11
2.2.8
off ............................................................................................................
2.2.7
Options
10
2.2.6
Canceling
the current
program ........................................................................ 11
2.2.7 Removing
Options ......................................................................................................................
......................................................................................................................
11
2.2.9
dishes ............................................................................................
12
2.2.8
off
............................................................................................................
12
2.3
Additional
function
............................................................................................... 11
13
2.2.77 Switching
Options
......................................................................................................................
2.2.8
Switching
off
............................................................................................................
12
2.2.9
Removing
the
dishes
............................................................................................
12
2.3.1
water
............................................................................. 12
13
11
2.2.88 Adjusting
Switching the
off
2.2.9
Removing
the............................................................................................................
dishessoftener
............................................................................................
2.3
Additional
function
............................................................................................... 13
2.3
Additionalthe
function
13
2.2.9 Removing
dishes...............................................................................................
............................................................................................ 12
2.3.1
Adjusting
the
water
softener
13
ENERGY
SAVING
AND
ENVIRONMENTAL
RESPECT ............................................. 15
12
2.3.1 Adjusting
water ...............................................................................................
softener .............................................................................
.............................................................................
13
2.3
Additionalthe
function
12
3.1 Reducing
of detergent
and respecting the environment.. 16
2.3.1
Adjustingthe
theconsumption
water
softener
.............................................................................
13
ENERGY
ENVIRONMENTAL
TROUBLESHOOTING
ENERGY SAVING
SAVING AND
AND........................................................................................................
ENVIRONMENTAL RESPECT
RESPECT .............................................
............................................. 15
15
ENERGY SAVING
AND ENVIRONMENTAL
RESPECT ............................................. 15
OPERATING
INSTRUCTIONS
..........................................................................................
18
TROUBLESHOOTING
13
TROUBLESHOOTING ........................................................................................................
........................................................................................................ 16
16
5.1 Using the water softening system (on some models only) .................... 18
TROUBLESHOOTING
........................................................................................................
OPERATING
INSTRUCTIONS
.......................................................................................... 16
18
15
OPERATING
INSTRUCTIONS
18
5.2
Using
the
rinse-aid
and..........................................................................................
detergent
dispenser
..............................................
20
5.1
Using
the
water
softening
system
(on
some
models
only)
....................
18
15
OPERATING
INSTRUCTIONS
..........................................................................................
5.1 Using the
water softening
system (on some models only) .................... 18
5.2.1 Using
Addingthe
therinse-aid
rinse-aidand
.............................................................................................
21
5.2
detergent
dispenser
..............................................
20
17
5.1 Using the
the water softening
system (on
some models
only) .................... 18
5.2
and dispenser
detergent
dispenser
..............................................
20
5.2.2 Using
Adjusting rinse-aid
the rinse-aid
setting
.....................................................
21
5.2.1
Adding
the
rinse-aid
.............................................................................................
21
18
5.2
Using
the
rinse-aid
and
detergent
dispenser
..............................................
20
5.2.1
Adding
the
rinse-aid
.............................................................................................
21
5.2.3
detergent ........................................................................................... 22
5.2.2
Adjusting
the
rinse-aid
dispenser
setting
.....................................................
21
18
5.2.1
Adding
the
rinse-aid
5.2.2 General
Adjusting
the
rinse-aid
dispenser setting .....................................................
5.3
warnings
and.............................................................................................
recommendations
.................................................... 21
24
5.2.3
Adding
the
detergent
...........................................................................................
22
19
5.2.2
Adjusting
the
rinse-aid
dispenser setting ..................................................... 21
5.2.3 Using
Addingthe
theracks
detergent
...........................................................................................
22
5.4
........................................................................................................
26
5.3
General
warnings
and
recommendations
....................................................
24
21
5.2.3
Adding
the
detergent
22
5.3 Lower
Generalrack
warnings
and...........................................................................................
recommendations .................................................... 24
5.4.1
.................................................................................................................
27
5.4
Using
the
racks
........................................................................................................
26
23
5.3
General
warnings
and
recommendations
....................................................
24
5.4
Using
the
racks
........................................................................................................
26
5.4.2 Cutlery basket.......................................................................................................... 29
5.4.1
Lower
rack
.................................................................................................................
27
24
5.4
Using
........................................................................................................ 30
26
5.4.1 Upper
Lowerthe
rackracks
.................................................................................................................
27
5.4.3
................................................................................................................
5.4.2
Cutlery
basket
..........................................................................................................
29
26
5.4.1
.................................................................................................................
27
5.4.2 Lower
Cutleryrack
basket
.......................................................................................................... 29
5.4.3
Upper
rack
................................................................................................................
30
27
5.4.2
Cutlery
basket
..........................................................................................................
29
5.4.3
Upper
rack
................................................................................................................
30
CLEANING AND USER MAINTENANCE ...................................................................... 33
5.4.3 General
Upper rack
................................................................................................................
6.1
warnings
and recommendations .................................................... 30
33
30
CLEANING
AND
USER
MAINTENANCE
......................................................................
CLEANING
ANDthe
USER
MAINTENANCE
...................................................................... 33
33
6.2 Cleaning
water
intake filter.........................................................................
34
30
6.1
General
warnings
and
recommendations
....................................................
33
CLEANING
AND
USER
MAINTENANCE
......................................................................
33
6.1
General
warnings
and
recommendations
....................................................
6.3 Cleaning the spray arms ...................................................................................... 34
6.2
Cleaning
the
water
intake
filter
.........................................................................
34
31
6.1 Cleaning
General warnings
recommendations
.................................................... 36
33
6.2
waterand
intake
filter.........................................................................
34
6.4
the filter
unit
.........................................................................................
31
6.3
Cleaning
the
spray
arms
......................................................................................
34
6.2
Cleaningwarnings
the water
intake
filter.........................................................................
6.3 General
sprayand
arms
......................................................................................
6.5
recommendations
for correct maintenance ... 34
37
33
6.4
Cleaning
the
filter
unit
.........................................................................................
36
6.3
Cleaning the spray
arms
......................................................................................
34
6.4 Troubleshooting
filterminor
unit
.........................................................................................
6.6
problems
.................................................................... 36
38
34
6.5
General
warnings
and
recommendations
for
correct
maintenance
...
37
6.4
the filter and
unitrecommendations
.........................................................................................
6.5 Cleaning
General warnings
for correct maintenance ... 36
37
35
6.6
minor
problems
38
6.5
General
warnings
andINSTRUCTIONS
recommendations
for correct maintenance ... 40
37
6.6 Troubleshooting
Troubleshooting
minor
problems ....................................................................
....................................................................
38
IMPORTANT
SAFETY
AND
.............................................................
6.6 Troubleshooting minor problems .................................................................... 38
IMPORTANT
AND
.............................................................
37
IMPORTANT SAFETY
SAFETY
AND INSTRUCTIONS
INSTRUCTIONS
............................................................. 40
40
INSTALLATION
AND HOOK-UP
.....................................................................................
46
IMPORTANT SAFETY AND INSTRUCTIONS ............................................................. 40
INSTALLATION
AND
HOOK-UP
46
43
INSTALLATION
AND
HOOK-UP.....................................................................................
..................................................................................... 48
46
TECHNICAL
DATA
...............................................................................................................
INSTALLATION AND HOOK-UP..................................................................................... 46
TECHNICAL
45
TECHNICAL DATA
DATA...............................................................................................................
............................................................................................................... 48
48
TECHNICAL DATA............................................................................................................... 48
1
1
1
1
EN
2
EN
INTRODUCTION
1
INTRODUCTION
Thank you for choosing one of our products. To use this dishwasher
correctly and safely, please read this manual carefully. The manual is
divided into sections giving you a step-by-step guide to all your appliance’s functions.
The texts are easy to understand and are complete with detailed illustrations. Following the cleaning instructions provided here will keep
dishwasher performance at peak levels in the long term. This userfriendly manual will provide answers to all your questions about use
of the dishwasher.
This manual comprises the following sections:
INTRODUCTION: general information about the manual.
USER INSTRUCTIONS: advice on using the washing programs and information about all the dishwasher functions.
Useful advice is provided for the use of racks, spray arms, containers
and filters.
WARNINGS: a list of warnings concerning safety and use of the dishwasher.
INSTALLATION INSTRUCTIONS: for the qualified technician who
must carry out the installation, hook-up and testing of the appliance.
Nomenclature of figures and tables:
The progressive number of each figure is shown in the bottom righthand corner of the relative box. An example of a progressive number
is “Fig. 4-01”, where the first number (4) indicates the section to which
the figure belongs, while the second number (01) indicates the progressive number of the figure in section 4 (Fig. 4-01 is the first figure in
section 4). The tables are numbered in the same way, bearing in mind
that “Tab.” is used instead of “Fig.” (e.g.: Tab. 4-01 is the first table in
section 4). If a table occupies more than one page, a letter is added
after the progressive number (e.g.: “Tab. 4-01a”, Tab. 4-01b”).
3
EN
INTRODUCTION
Symbols used in this manual (see tab. 1-01)
DANGER. This symbol highlights information and warnings
which, if not observed, may compromise personal safety or damage the appliance.
DANGER OF ELECTROCUTION. This symbol highlights information and warnings of an electrical nature which, if not observed,
may compromise personal safety or damage the appliance.
This symbol highlights general information and warnings.
Tab. 1-01
4
EN
USER INSTRUCTIONS
2
DESCRIPTION OF THE CONTROLS
2.1
Upper panel
All the dishwasher controls are grouped on the upper panel (see fig. 2-01). The
dishwasher can only be switched on, programmed, switched off, etc. with the
door open.
A brief description (see tab. 2-01) of the various controls on the upper panel is
given below.
2
3
4 5
7
6
9
8
1
Sanitized
QuickTime
end
9h 6h
Auto
3h
QuickTime
FIG. 2-01
The panel shown is indicative, programs and options may vary depending on model.
˜˜
5
EN
USER INSTRUCTIONS
EN
1
On/off button
Press to power the appliance.
2
Program indicator lights
These show which program is selected and whether there are any faults (Troubleshooting).
1
3
2
4
3
4
5
5
6
6
7
7
8
8
9
9
10
11
12
USER INSTRUCTIONS
On/off button
Press
to power
the appliance.
Program
selection
button
Press in sequence
select the required program..
Program
indicatortolights
These
show
which
program
is selected
whether there are any faults
Add salt indicator light
(only fitted
on someand
models)
(Troubleshooting).
Shows the appliance has run out salt.
Program
selection button
WATER HARDNESS
ADJUSTMENT ON INDICATOR LIGHT
Press
in sequence
to selectthat
the the
required
program.
The light
flashes to indicate
appliance
is in “water hardness adjustment” mode.
Add salt indicator light (only fitted on some models)
Add rinse aid indicator light
Shows the appliance has run out salt.
(only fi tted on some models)
Add
rinse
indicator
Shows
theaid
appliance
haslight
run out of rinse aid..
(only fitted on some models)
Quick time option button
Shows the appliance has run out of rinse aid.
Press this button to start one of the quick time programmes (see table).
Quick time option button
Quickthis
time
programmes
indicator
lighttime programmes (see table).
Press
button
to start one
of the quick
Showstime
that one
of the quick
time programmes
will be run
Quick
programmes
indicator
light
Shows
that
one
of
the
quick
time
programmes
will be run
Delayed Start Button
Pressing
this button
the start of the program by 3, 6 or 9 hours.
Extra
drying
optiondelays
button
Press to select the extra drying option
Delayed Start Lights
Extra
drying
option
indicator
light by 3, 6 or 9 hours has been set.
Illuminate
to show
that
start delayed
Shows
the function
is active lights
Sanitisation
confirmation
Sanitation
indicator
light simultaneously at the end of the wash cycle, sanitisation has
If the three lights
illuminate
Shows
that sanitation has been completed (see notes in the programmes table)
been completed
Programme delay button
Tab. 2-01
Press to delay the start of the programme up to 9 hours.
Information display
Tab. 2-01
2.2
Setting the washing program and switching
on and off
The dishwasher is equipped with a control panel (see fig. 2-02) which is used
to program the appliance and switch it on and off.
2
3
4 5
7
6
9
8
1
Sanitized
QuickTime
end
9h 6h
Auto
3h
QuickTime
FIG. 2-02
6
The manual contains the programs table for several models.
2
4 5
12 11 10 9 8 7 6
To select the most suitable program
for the3dishes
to wash, consult
the following 14
table which specifies the most appropriate type of washing sequence depending on
USER
INSTRUCTIONS
the kind of dishes and how
dirty they
are (see tabs. 2-02a and 2-02b)
13
end
Auto
LOAD
PROGRAMME, NUMBER &
DURATION
Sanitized
PROGRAM
CONSUMPTION
QuickTime
CROCKERY
To selecSYMBOL
t the most suitab
le program foPROGRESS
r the dishes MINUTES
to wash, consult tENERGY
he folWATER
AND
KWH (1)
lowing table which specifi
esCUTLERY
the most appropriate type(1)of washing sequence
end
depending on the kind of dishes and how dirty they are (see tabs. 2-02a and
Pans and
2-02b).
dishes awaiting
4.0l
2
12 11 10 9 8 157 6
14
13 0.02
1
SOAK 3 4 5 Auto
Cold prewash
1
PROGRAMME,
PROGRAMME,
NUMBER
& SYMBOL
completion
LOAD of
theLOAD
load.
CROCKERY
PROGRAM
PROGRAM
PROGRESS
CROCKERY
AND
CUTLERY
NUMBER & SYMBOL
PROGRESS
Wash
at 45°C
AND CUTLERY
Disheschina
with (113°F)
Glass,
Wash at 38°C
Pans
and Cold
light
dirt,
and
mixed
rinse
(100,4°F) end
CRYSTAL
dishes
RAPID 27’
washed
im- Rinse at 70°C
dishes
with
Rinse
at 50°C
RINSE mediately
awaiting
Cold prewash
light
dirt.after (158°F)
(122°F)
Auto
completion
of Dry
use.
end
the load Wash
Washatat45°C
45°C
Wash at 45°C
Glass, china (113°F)
(113°F)
Dishes
washed
Glass,
china Cold
AUTO
(113°F)
and mixed
Cold
rinse
rinse
Auto DELICATE
CRYSTAL
immediately
and mixed
Coldat
rinse
dishes
with
Rinse
at65°C
70°C
Rinse
CRYSTAL
after
(2)
Rinse at 70°C
dishes
with (149°F)
light use.
dirt.
(158°F)
end
(158°F)
Dry
light dirt. Dry
½
QuickTime
end
DURATION 1.06gal.
CONSUMPTION
DURATION CONSUMPTION
MINUTES
ENERGY
WATER ENERGY
MINUTES
(1)
WATER KWH (1)
(1)
Auto
Sanitized
2
1
1
32
2
E1
3
E3
Auto
Sanitized
end
Auto
E7
Auto
Auto
end
end
+
DELICATE
Auto
QUICK
end
E1
E9
Auto
Dishes with
light dirt.
end
3,17 gal.
12 l
13l
13gal.
l
3,45
3.43
3,45gal.
gal.
9
8
7
6
14
13
Cold prewash
Wash at 50°C
(122°F)
Cold rinse
Rinse at 70°C
(158°F)
1
100
140
13 l
12gal
l
17.5l
3,45
3,17 gal.
4.62gal.
1,00
0,7
1.2
122
18,3 l
18,3
l
7l gal.
4,83
4,83 gal.
1.84gal.
1,12
0.4
90
QuickTime
122
27
1,12
Tab. 2-02a
Tab. 2-02a
60
13l
3.43gal.
1.0
7
end
Auto
0,7
1.20
1,00
Auto
end
E2end
65
Auto
end
E8 7
12 l
10.2l
0,5
0.6-0.8
12
l
3,17
gal.
2.7
gal.
0,5
65
115-135
½
end
E6 655 +
0,02
Dry
Auto
end
0.95
0,4
0,93 gal.
100
120
90
after use Dry
2
5Wash at 65°C
12 11 10
Half
load 3of 4 Hot
prewash
Wash
at 50°C
(149°F)
Disheswith
with Wash
EXTREME enddishes
at 70°C
(122°F)
DAILY
HALF Dishes
normal
dirt,
Cold rinse
normalwith
dirt, (158°F)
WASH
Cold rinse
normal
dirt,
in- Rinse
Auto
LOAD
washed
imat 70°C
NORMAL
including
ETL
Cold
rinse
Rinse
at 66°C
cluding driedmediately
after
(158°F)
(2)
dried-on Rinse
SANITATION
at
70°C
(150,8°F)
on
residues.
use.
Dry
end
(158°F)
LISTED
residue
Dry
end
Dry
Auto
Hot prewash
Hot prewash
EXTREME
EXTREME AutoVery dirty Wash
at 70°C
Dishes
dirtywith
pans Wash at 70°C
WASH Very
end pans and
WASH
(158°F)
Wash
at
38°C
and
dishes,
inlight
dirt,
2(158°F)
cold rinses
dishes,
Auto
cluding
dried- (100°F)
2 cold rinses
RAPID
27’
washed
ETL SANITARinseatat50°C
70°C
onincluding
residues. Rinse
Rinse at 70°C
(158°F)
TIONETL
LISTED immediately
dried-on
(122°F)
(158°F)
SANITATION end
after
use. end
Dry
residue
LISTED
Dry
QuickTime
E5
15
Wash
at 50°C
prewash
Half load
of Cold
Washatat65°C
65°C
Dishes
with
(122°F)
Wash
end
Dishes
with
dishesdirt,
with
(149°F)
normal
in- (149°F)
Cold
rinse
NORMAL
(2) normal
enddirt,
in- Rinse
Auto
DAILY
HALF
normal
dirt,
Cold rinse
DAILY
WASH
cluding
driedat 66°C
Cold
rinse
cluding
dried- (158°F)
Rinse at 70°C
LOAD
onwashed
residues.
Rinse at 70°C
on
residues. Dry
(158°F)
end
immediately
(158°F)
Auto
E4 544
10l
6,5 l
2.64gal.
1,72
3,5gal.
l
Dry
Auto
E2 43
kWh (1)
QuickTime
75
27
1
EN
½
QuickTime
Auto
Auto
EN
USER INSTRUCTIONS
EN
2
3
USER INSTRUCTIONS
4 5
12 11 10
9
8
7
6
14
13
1
½
QuickTime
end
Auto
Sanitized
LOAD
CROCKERY
AND CUTLERY
PROGRAM
PROGRESS
Dishes with
normal dirt,
ECO QUICK
washed immediately after
use.
PROGRAMME, NUMBER &
SYMBOL
end
Auto
8
+
end
+
NORMAL
QUICK
Dishes with
normal dirt,
washed immediately after
use.
+
STRONG and
FAST
Mixed dishes
with normal
dirt without
dried-on residues.
Auto
9
QuickTime
DURATION
CONSUMPTION
MINUTES
(1)
WATER
ENERGY
KWH (1)
Cold prewash
Wash at 60°C
(140°F)
Cold rinse
Rinse at 70°C
(158°F)
85
13l
3.43gal.
1.2
Cold prewash
Wash at 65°C
(149°F)
Cold rinse
Rinse at 70°C
(158°F)
90
13l
3.43gal.
1.3
Wash at 65°C
(149°F)
Cold rinse
Rinse at 70°C
55
10l
2.64gal.
1.12
end
Auto
10
end
Auto
end
Tab. 2-02
Auto
Auto
Auto
Auto
(1)end The cycle times and electrical energy listed use and care manual are based on normal soil
loads and 120°F (49°C) incoming water and will vary based on your actual conditions.
(2) Program for energy star.
- end Only “EXTREME WASH” program conforms to NSF std 184 and is certified by INTERTEK with
therun
ETLthe
SANITATION
LISTED.with half loads.
Only
soak program
Only
runthree
the soak
soak
program
with
half loads.
loads. the end of the wash cycle, the dishwasher’s
run
the
with
-Only
If the
lightsprogram
illuminate
simultaneously
To run
programmes
6, 7, 8, 9,
10,half
select theatrequired
standard programme and
To
programmes
6,
7,
8,
9,
10,
select
the
required
programme
and
end run
contents
and the dishwasher
itself
have been
sanitised
instandard
compliance
with National
SanitisaTo
run
programmes
6,
7,
8,
9,
10,
select
the(ref.
required
standard
programme
and
then
press
the
quick
time
option
button
6
fig.
2-02).
Only
run
the
soak
program
with
half
loads.
Only
run
the
program
with half
loads.(ref.
tion
Foundation
(NFS)
requirements.
then
press
thesoak
quick
time
option
button
(ref. 6
6 fig.
fig. 2-02).
2-02).
then
press
the
quick
time
option
button
USER
USER INSTRUCTIONS
INSTRUCTIONS
USER
USER INSTRUCTIONS
INSTRUCTIONS
USER INSTRUCTIONS
After
the above
tables
therequired
most suitable
washing
cycle, program
To
run
programmes
6,
8,
10,
select
standard
programme
and
To
runusing
programmes
6, 7,
7,
8, 9,
9, to
10,choose
select the
the
standard
programme
and
After
using
the above
above
tables
to
choose
therequired
most suitable
suitable
washing
cycle, program
program
After
using
the
tables
to
choose
the
most
washing
cycle,
the
appliance.
then
press
the
quick
time
option
button
(ref.
6
fig.
2-02).
Only
run
the
soak
program
with
half
loads.
then
press
the
quick
time
option
button
(ref.
6
fig.
2-02).
the
appliance.
therun
appliance.
After
using
the
tables
the
most
washing
cycle,
To
programmes
6, 7,
8, 9, to
10,
select the
required
standard
programme
and
Before
starting
achoose
washing
program,
make
sure
that:
After
using
the above
above
tables
to
choose
the
most suitable
suitable
washing
cycle, program
program
Before
starting
a washing
washing
program,
make
sure that:
that:
Before
starting
a
the
then
press the quick
time
option
button
(ref.
6 fig.make
2-02).sure
• The
water
supply
tap isprogram,
open.
the appliance.
appliance.
•• The
water
supply
tap
is
open.
Thetables
water
supply
tapthe
isprogram,
open.
After using the above
to
choose
most suitable
washing
cycle,
program
•Before
The
correct
amount
of
detergent
has
been
added
to the
disBefore
starting
a
washing
make
sure
that:
starting
a
washing
program,
make
sure
that:
•
The
correct
amount
of
detergent
has
been
added
to
the
disThe
correct
amount
of
detergent
has
been
added
to
the
disthe appliance. •• The
penser
(to
add
detergent,
see
the
instructions
in
the
general
water
supply
tap
is
open.
• The
water
supply
tap
is
open.
penser (to
(to add
add detergent,
detergent, see
see the
the instructions
instructions in
in the
the general
general
penser
manual).
•Before
The
correct
amount
of
detergent
has
been
added
to
the
disstarting
a
washing
program,
make
sure
that:
• The
correct amount of detergent has been added to the dismanual).
manual).
spray
able
to see
rotate
and without
(to
add
detergent,
the
instructions
in
general
• penser
The
water
supply
tap
is open.
(toarms
add are
detergent,
thefreely
instructions
in the
theobstrucgeneral
•• penser
The
spray
arms
are
able
to
rotate
freely
and
without
obstrucThe spray
arms
are
able
to see
rotate
freely
and added
without
obstruction.
• manual).
The
correct
amount
of
detergent
has
been
to
the
dismanual).
tion.
tion.
racks
correctly
loaded
(see
the
instructions
in
•• The
spray
arms
are
able
to
rotate
and
without
penser
(tohave
addbeen
detergent,
see
thefreely
instructions
in theobstrucgeneral
The
spray
arms
are
able
to
rotate
freely
and
without
obstrucracks have
have been
been correctly
correctly loaded
loaded (see
(see the
the instructions
instructions in
in
• tion.
The general
racks
the
manual).
manual).
tion.
the
general
manual).
the
general
manual).
door
is securely
closed.
• The dishwasher
racks
correctly
loaded
instructions
in
spray have
arms been
are
able
to rotate
freely(see
andthe
without
obstrucracks
have
been
loaded
•• The
door
is
closed.
The dishwasher
dishwasher
door correctly
is securely
securely
closed.(see the instructions in
the
tion.
the general
general manual).
manual).
•• The
door
is
closed.
racks have been
loaded
The dishwasher
dishwasher
door correctly
is securely
securely
closed.(see the instructions in
the general manual).
2.2.1
Switching
on
2.2.1
ondoor is securely closed.
•Switching
The dishwasher
Press the on/off button (ref. 1 fig. 2-02) to start the dishwasher. Then wait for one
2.2.1
Switching
Press
the on/off
on/off button
button
(ref. 1
1 fig.
fig.on
2-02) to
to start
start the
the dishwasher.
dishwasher. Then
Then wait
wait for
for one
one
Press
the
(ref.
2-02)
2.2.1
Switching
on
of the program indicator lights to turn on (ref. 2 fig. 2-02).
of the
thethe
program
indicator
lights
to
turnto
onstart
(ref.the
2 fig.
fig.
2-02).
Press
on/off
button
(ref.
1
2-02)
dishwasher.
Then
of
program
lights
turn
(ref.
2
2-02).
Press
the
on/off indicator
button
(ref.
1 fig.
fig.to
2-02)
toon
start
the
dishwasher.
Then wait
wait for
for one
one
2.2.1
Switching
on
of
the
program
indicator
lights
to
turn
on
(ref.
2
fig.
2-02).
of thethe
program
lights
turntoonstart
(ref.the
2 fig.
2-02).
Press
on/off indicator
button (ref.
1 fig.to
2-02)
dishwasher.
Then wait for one
end
Auto
end
Auto
end
Auto
end
Auto
8
EN
EN
EN
EN
EN
EN
USERINSTRUCTIONS
INSTRUCTIONS
USER
2.2.2
EN
Selecting and starting the program
• Press the program selection button (ref. 3 fig. 2-02) several times until
the indicator light corresponding to the required program turns on (ref. 2 fig.
2-02);
• if required, press the relative buttons to select any complementary functions
(e.g.: “extra drying”, “program delay”; see para 2.2.7 “options”);
• close the door; the program will start after about 2 seconds and the relative
indicator light will flash throughout the cycle (program¬ running signal).
IMPORTANT
USER
If thedoor
doorofofthe
the dishwasher
dishwINSTRUCTIONS
asher hmust
as notbe
beeclosed
n closedwithin
or has4beseconds
en incorThe
rectlyuse
closed,
theprogram
washing cycle
will not
begin.for all functions (e.g.
after
of the
selection
button
program selection, change, deletion, etc.).
2.2.2 S
lecdoor
tingisanot
ndclosed
starting the program
If e
the
QUICK
TIME
PROGRAMS
OPTION within 4 seconds, one or more program
OPTION
•FAST
PreCYCLES
ss tlights
he program
selection
button
(ref. operation)
3 fig. 2-02)will
several
times
until
(depending
on the
current
flash
at high
Select
this
option
together
with
any
washing
program
(except
the
soak
proindicator
light
corresponding
to
the
required
program
turns
on
(ref.
2
fig.
•• the
Select
this
option
together
with
any
washing
program
(except
the
soak
speed to indicate that the operation must be confirmed before
gram)
to
SHORTEN
the
cycle
by
from
a
minimum
of
10%
to
a
maximum
2-02);
program)
to
SHORTEN
the
cycle
by
from
a
minimum
of
10%
to
a
maxithe door is closed.
55%,To
the cycle
selected.
To activate
option,
press
the
• ifof
required,
pressdepending
theon
relative
buttons
to select
any complementary
functions
mum
ofdepending
55%,
on
the
cycle
selected.
Tothis
activate
this
option,
confirm,
simply
press
the
program
selection
button
once
(e.g.:
“extra
drying”,
“program
delay”;
see close
para 2.2.7
“options”);
(light
comes
on) door
after
selecting
thestart/
proQUICK
TIME
OPTION
button
and
the
flashes
will slow
down;
the
at once to
pressthe
thedoor;
FASTthe
CYCLES
button
(light
comes
on) after
the
• close
program
willautomatically
start after
about
2 seconds
the relative
gram
required.
The
option
is
deactivated
at and
theselecting
end
of the
restart the
dishwasher.
program
required.
The
option
is
automatically
deactivated
at
the
end
of
iprogram.
ndicatoThe
r lighsame
t will flapplies
ash throifugthe
houdishwasher
t the cycle (pisroopened
gram¬ ruwith
nningthe
sigprogram
nal).
the program.
delay option set and the cycle not started (e.g. to add more
dishes):
eo
dof the
opr roofprogram
threadm
ishwselection
asher has nbutton
ot beenmust
closebe
d opressed
r has beenbefore
incor2.2.3 the
EIfnthddoor
g
is closed,
restarting
delay countdown.
rectly closed,
the washing
cyclethe
willprogram
not begin.
The end of
is signaled
by a short
beep.
Additionally
thehas
indicator
If the program
door of the
dishwasher
has not
been
closed or
been
light of theincorrectly
normal anclosed,
d strongthe
prog
rams (macycle
rked “will
endnot
”) flabegin.
sh.
washing
EN
˜˜
˜˜
QUICK
TIME PROGRAMS
FAST
CYCLES
OPTION OPTION
.4 this
Intoption
eoption
rruptogether
titogether
ng a p
rwith
ogany
raany
m
Select
with
washing
program
(except
the soak
••2.2
Select
this
washing
program
(except
the prosoak
to SHORTEN
the
cycle
by from
a minimum
to a maximum
program)
to current
SHORTEN
the cycle
byopen
from
a minimum
of 10%
to a maxiTo gram)
interrupt
the
program
simply
the
doorofof10%
the
dishwasher;
to
of
55%,
on theclose
cycle
selected.
To activate
this
option,
press
the
mum
55%, depending
on the
cycle
selected.
activate
this
option,
restart
theofdepending
program,
simply
the
door again.
TheToprogram
restarts
from
(light comes on) after selecting the prowhQUICK
ere it waTIME
s interOPTION
rupted. button
pressrequired.
the FASTThe
CYCLES
button
(lightdeactivated
comes on) after
the
gram
option
is automatically
at theselecting
end of the
program
2.2program.
.5 Chrequired.
anging The
theoption
curreisntautomatically
program deactivated at the end of
the program.
To change the current program, simply open the door of the dishwasher and
s
e.2
le.c3t thEnd
eEnn
ew
poro
gprarm
.C
se the door to run the new program automatically.
22.2.3
dof
fprogram
og
ralom
The end of the program is signaled by a short beep. Additionally the indiThe
of of
thethe
program
signaled
by programs
a short beep.
Additionally
indicator
catorend
light
normalisand
strong
(marked
“end”)the
flash.
lig2.2.4
ht of theInterrupting
normal and stroa
ngprogram
programs (marked “end”) flash.
To.2interrupt
2
.4 Intthe
errcurrent
uptingprogram
a progsimply
ram open the door of the dishwasher;
10
to restart the program, simply close the door again. The program restarts
To
interrupt
current
program simply open the door of the dishwasher; to
from
where the
it was
interrupted.
restart the program, simply close the door again. The program restarts from
2.2.5 Changing the current program
where it was interrupted.
To change the current program, simply open the door of the dishwasher
and
the
2
.2.5select
Chthe
annew
gingprogram.
the curClose
rent p
rodoor
gramto run the new program automatically.
To change the current program, simply open the door of the dishwasher and
select the new program. Close the door to run the new program automatically.
9
EN
EN
USERINSTRUCTIONS
INSTRUCTIONS
USER
2.2.6
Canceling the current program
• To cancel the current program, open the door and press and hold down the
program selection button (ref. 3 fig. 2-02) for a few seconds until the indi2
3 (ref.
4 5 pr. 4, pr. 5 fig.12
11 10
cator lights of the fourth and fifth programs
turn on
2-03).
• Close the door again.
• After about 1 minute, the dishwasher terminates the cycle and the indicator
lights of the fourth and fifth programs (ref. pr. 4, pr. 5 fig. 2-03) start flashing.
9
8
7
½
QuickTime
end
Auto
Sanitized
QuickTime
end
Auto
FIG. 2-03
symbols programs according to the models
2.2.7
Options
end
Function designed for loads with hard to dry item s such as saucepans, nonstick pans and plastic containers. Increases
Auto the hot rinse temperature and can
be used in programmes featuring a final drying phase (see programmes table).
PROGRAM DELAY
(available for all programs except soak)
The “Program delay” function delays the beginning of the washing program
end
up to 9 hours from the moment in which programming takes place. This makes
E1
it possible to use theAuto
dishwasher at a certain time of day.
Before programming a delay, open the door of the dishwasher, select the
required washing program (seeendpara 2.2 “Setting the washing program and
switching on and off”).
E2
AutoSelect the day by pressing the Program delay button
(ref. 11 fig. 2-02); each time you press the button, the display increases the
delay before the appliance starts
by 1 hour.
end
E3
Auto
E4
Auto
end
end
E5
Auto
end
E6
Auto
10
11
end
6
½
QuickTime
end
EN
USER
USERINSTRUCTIONS
INSTRUCTIONS
EN
Auto
2.2.7
8
Switching off
Sanitized
QuickTime
end
At the end of the program, the dishwasher emits a short beep and the indiAuto
cator lights of the fourth and fifth
program (ref. pr. 4, pr. 5 fig. 2-04) flash.
Turn off the appliance by opening the door and pressing the on/off button (ref.
1 fig. 2-02).
end
Auto
symbols programs according to the models
E1
E2
FIG. 2-04
If it is necessary to end
open the door during the washing cycle, the
program will
Autobe interrupted, the relative indicator light will continue to
flash and a beep will indicate that the cycle has not terminated. Wait
for about 1 minute before
closing the door and continuing with the
end
program. When the door closes, the program will start from where it
Auto
was interrupted. This operation should be performed only if necessary as it could cause irregular program performance.
end
E3
4 8 REMOVING THE DISHES
2.2.9
Auto
end
E4
˜˜˜
E5
At the endAuto
of the washing program, wait at least 20 minute before
removing the dishes in order to allow them to cool. To prevent any
water droplets on theendupper rack from falling onto the dishes in the
lower rack,Auto
empty the lower rack first and then the upper one.
end
E6
Auto
end
E7
Auto
E8
Auto
end
end
E9
Auto
11
12
end
EN
EN
USERINSTRUCTIONS
INSTRUCTIONS
USER
3
ENERGY SAVING AND ENVIRONMENTAL
RESPECT
Always try to run the dishwasher fully loaded.
Do not wash the dishes under a running tap.
Use the most suitable washing program for each type of load.
Do not pre-rinse.
If available, connect the dishwasher to a hot water system with a temperature of up to 60°C (140°F).
• When possible, skip the drying cycle by opening the door after washing:
the air and the residue heat will dry the dishes to perfection.
•
•
•
•
•
3.1
Reducing the consumption of detergent
and respecting the environment
The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity:
• Separate the more delicate items from those that are more resistant to aggressive detergents and high temperatures;
• Do not pour the detergent directly onto the dishes.
12
15
13
EN
USER
INSTRUCTIONS
USER
INSTRUCTIONS
USER
INSTRUCTIONS
4
EN
TROUBLESHOOTING
The dishwasher can to signal a number of malfunctions by turning on various
indicator lights, as described below (see following table):
FAULT
E1
E2
E3
E4
E5
DESCRIPTION
Acquastop failure
The anti-flooding system has tripped (only for models
fitted with this feature). Activates in case of water leaks.
Contact the technical assistance service.
Safety level
The system limiting the water level in the dishwasher
has tripped. Interrupt the current program. Switch off
the dishwasher, switch it back on again, program a new
cycle and press start. If the problem persists, contact
the technical assistance service.
Water heating malfunction
The water is not heated or is incorrectly heated. Repeat
the washing program; if the problem persists, contact
the technical assistance service.
Water temperature monitoring malfunction
Interrupt the current program. Switch off the dishwasher,
switch it back on again, program a new cycle and press
start. If the problem persists, contact the technical
assistance service.
Water intake malfunction
The appliance does not take in water or does so
incorrectly. Make sure the water connections are
correct, that the water supply tap is open and that the
filter is not clogged. If the problem persists, contact the
technical assistance service.
Tab. 4-01a
16
14
13
E1
EN
Auto
USER
INSTRUCTIONS
USER
INSTRUCTIONS
USER
INSTRUCTIONS
EN
DESCRIPTION
USER
INSTRUCTIONS
USER
INSTRUCTIONS
Water pump-out malfunction
USER
INSTRUCTIONS
USER
INSTRUCTIONS
EN
EN
EN
end
E2
Auto
FAULT
E3
Auto
E6
FAULT
Auto
FAULT
E4
FAULT
E6
E5
E6
end
USER
INSTRUCTIONS
USER
INSTRUCTIONS
end
end
Auto
E7
E6
end
E6
Auto
end
E7
E7
E7
Auto
E8
E7
end
E8
Auto
E8
E9
end
E8
E9
Auto
E8
end
E9
E11
E11
E9
E9
Light off
Auto
The appliance does not pump out the water or does so
incorrectly. Make sure the drain hose is not kinked or
DESCRIPTION
crushed and that the
siphon and filters are not clogged.
DESCRIPTION
IfWater
the problem
persists,
contact the technical assistance
pump-out
malfunction
service.
Water
pump-out
malfunction
The appliance
does
not pump out the water or does so
DESCRIPTION
The
appliance
does
notthe
pump
outhose
the water
does so
incorrectly.
Make
sure
drain
is notorkinked
or
Turbine
flow-regulator
malfunction
incorrectly.
sure
the this
drain
is not
or
Water
malfunction
crushed
andMake
thatfitted
the
siphon
and
fihose
lters are
notkinked
clogged.
(only
forpump-out
models
with
feature)
crushed
and that
siphon
and
filters
aremeasure
not
clogged.
does
not
pump
out
the
water
or
doesthe
so
If theappliance
problem
persists,
contact
the
technical
assistance
The
appliance
istheunable
to
precisely
Ifservice.
the problem
persists,
contact
technical
incorrectly.
Make
sure
the Interrupt
drainthe
hose
notassistance
kinked
or
quantity
of incoming
water.
the is
current
program
service.
crushed
siphon
and
filters itare
noton
clogged.
and
switch
offthat
thethe
dishwasher.
Switch
back
again,
Turbine
fland
ow-regulator
malfunction
If the for
problem
persists,
contact
thestart.
technical
assistance
program
new
and
press
If the
problem
Turbine
flaow-regulator
malfunction
(only
models
ficycle
tted with
this
feature)
service.
persists,
contactfiisthe
technical
service. the
(only
for
models
tted
with this
feature)
The
appliance
unable
to assistance
precisely measure
The
appliance
is unable
to
precisely
measure
the
Turbine
flow-regulator
malfunction
quantity
of
incoming
water.
Interrupt
the current
program
Alternate
washing
system
malfunction
quantity
incoming
water.
Interrupt
theitcurrent
program
(onlyswitch
for of
models
fitted
with
this feature)
and
off the
dishwasher.
Switch
back on
Interrupt
the
current
program
and
switch
offagain,
the
and
the
dishwasher.
back
The switch
appliance
iscycle
unable
precisely
the
program
a off
new
and to
press
start.itprogram
Ifmeasure
theon
problem
dishwasher.
Switch
it back
onSwitch
again,
aagain,
new
program
aincoming
new cycle
press
start.
If service.
the program
problem
quantity
of
Interrupt
thepersists,
current
persists,
contact
thewater.
technical
assistance
cycle
and
press
start.
Ifand
the
problem
contact
persists,
contact
technical
assistance
service.
andtechnical
switch
offassistance
thethe
dishwasher.
Switch it back
on again,
the
service.
Alternate
washing
system
malfunction
program athe
newcurrent
cycle
and
press
start.switch
If the problem
Alternate
washing
system
malfunction
Interrupt
program
and
off the
persists,
contact
the ittechnical
service.
Interrupt
theSwitch
current
program
and program
switch
off
the
Water intake
system
malfunction
dishwasher.
back
onassistance
again,
a new
dishwasher.
Switch
it assistance
back
again,
programcontact
a new
Contact
technical
service.
Alternate
washing
system
malfunction
cycle
andthe
press
start.
If the on
problem
persists,
cycle
and the
press
start. Ifprogram
the problem
Interrupt
current
and persists,
switch contact
off the
the technical
assistance
service.
the
technical Switch
assistance
service.
dishwasher.
it back
on again, program
new
Tab. a4-01b
cycle
press
start. malfunction
Ifdoes
the problem
persists, contact
Waterand
intake
system
Wash
motor
pump
not work
Water
intake
systemassistance
malfunction
the
technical
assistance
service. service.
Contact
the technical
Light
on the technical assistance
Light
flashing
Contact
service.
Water intake system malfunction
Tab. 4-01b
Contact the technical assistance service. Tab. 4-01b
If an alarm situation occurs, the dishwasher interrupts the current program and
Light off
Light on
Light flashing
Tab. 4-01b
signalsLight
the fault.
off
Light flashing
Light on
• Alarms E1, E2, E3, E4, E8, E9 immediately terminate the current program.
Light off E6 interrupt the current
Light on
Light
flashinghas been
Alarms
program
and, after
problem
If• an
alarmE5,
situation occurs, the dishwasher
interrupts
thethe
current
program and
eliminated,
resume
the
cycle.
Ifsignals
an
alarm
situation
occurs,
the
dishwasher
interrupts
the
current
program and
the fault.
•• A
Alarm
E7
is
displayed
at
the
end
of
the
cycle
which,
however,
is
completed
signals
the
fault.
laalarm
rms E1,
E2, E3,
E4, E8,
immediately
terminate
the
current
program.
If• an
situation
occurs,
theE9
dishwasher
interrupts
the
current
program
and
given
that
it
does
not
jeopardize
the
operation
of
the
dishwasher.
A
l
a
r
m
s
E1,
E2,
E3,
E4,
E8,
E9
immediately
terminate
the
current
program.
•signals
Alarms
E5,
E6
interrupt
the
current
program
and,
after
the
problem
has been
the
fault.
“reset” E5,
an aE6
larm
: the cycle.
•To Alarms
interrupt
the current program and, after the problem has been
eliminated,
resume
•• A
laerm
srE1,
E2,
E3,
E4,
E8,
the
o
p
n
o
c
l
o
s
e
t
h
e
d
o
o
r
,
o
rthe
swE9
iend
tchimmediately
tof
hethe
appcycle
liancterminate
ewhich,
on andhowever,
backcurrent
off is
agcompleted
aprogram.
in. At this
eliminated,
resume
the
cycle.
•• Alarm
E7
isE6
displayed
atthe
Alarms
E5,
interrupt
current
program
and,
after
the
problem
has been
point,
the
dishwasher
can
be
programmed
again.
• Alarm
E7
is
displayed
at
the
end
of
the
cycle
which,
however,
is
completed
given that itresume
does not
operation of the dishwasher.
eliminated,
thejeopardize
cycle. the
given
that
italdoes
not
jeopardize
the operation of the dishwasher.
T
o
“
r
e
s
e
t
”
a
n
a
r
m
:
I
f
t
h
e
f
a
u
l
t
p
e
r
s
i
s
t
s
,
c
o
n
t
a
c
t
t
h
e Acycle
uthoriwhich,
zed Techowever,
hnical Assisiscompleted
tance Seris displayed
at the end of the
rpeesnetoContact
”E7
m
o“E11:
ravice.
cnloitasldoes
eartthe
he: d
oorjeopardize
, or switservice.
ch the
the operation
appliance of
onthe
anddishwasher.
back off again. At this
••T•o Alarm
after-sales
given
that
not
• open othe
r clodishwasher
se the door,can
or sbe
witprogrammed
ch the applianagain.
ce on and back off again. At this
To point,
“reset”the
andishwasher
alarm:
point,
can be programmed again.
• open or Icf ltohseefathuelt dpoeorsr,isotrs,scwoitncthactht ethaepApuliathnocreizoend aTned
chbnaiccakl oAfsf saigstaainn.cAetStheirsIvice.
f tdishwasher
he fault perscan
ists,be
conprogrammed
tact the Authagain.
orized Technical Assistance Serpoint, the
vice.
If the fault persists, contact the Authorized Technical Assistance Service.
14
17
15
EN
EN
USERINSTRUCTIONS
INSTRUCTION
USER
USER
INSTRUCTIONS
USER
INSTRUCTION
5
5
EN
OPERATING INSTRUCTIONS
INSTRUCTIONS
OPERATING
BEFORE STARTING TO USE THE APPLIANCE, MAKE SURE YOU HAVE
BEFORE STARTING TO USE THE APPLIANCE, MAKE SURE YOU HAVE
READ AND UNDERSTOOD ALL THE WARNINGS CONTAINED IN CHAPREAD AND UNDERSTOOD ALL THE WARNINGS CONTAINED IN CHAPTER 2 “IMPORTANT SAFETY INSTRUCTION”.
TER 2 “IMPORTANT SAFETY INSTRUCTION”.
Once the dishwasher has been correctly installed, prepare for use as follows:
Once the dishwasher has been correctly installed, prepare for use as follows:
•
•
•
5.2
5.1
adjust
adjustthe
thewater
watersoftening
softeningsystem;
system;
add
addthe
theregenerating
regeneratingsalt;
salt;
add
addthe
therinse-aid
rinse-aidand
anddetergent.
detergent.
rinse-aid
and detergent
Using the water
softening
system dispensers
The
aid dispensers
are situated
on the inner
the door:
The detergent
amount ofand
scalerinse
contained
in the water
(water hardness
index)part
canof
cause
whitthestaining
detergent
dispenser
A tend
fig. 5-03)
is ondull
theover
left,time.
andThe
thedishwasher
rinse-aid
ish
on the
dry dishes,(ref.
which
to become
is
equipped(ref.
with
an 5-03)
automatic
softening
dispenser
B fig.
is on the
right. system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water
hardness level 3 (average hardness 41-60°dF – 24-31°dH / 23.6-35 gpg). When using water ofAmedium hardness, the regenerating salt container should be refilled
approximately20 washing
20 washing
salt can
container
can hold
after approximately
cycles. cycles.
The salt The
container
hold approximately
1.7
Kg (3.75 lb)1.5
of salt
in grains.
equipped
an opticalwith
no-salt
approximately
Kg (3.3
lb) ofSome
salt inmodels
grains. are
Some
modelswith
are equipped
an
optical no-salt
indicator.
these
the
cap of the
salt container
contains
indicator.
In these
models,Inthe
cap models,
of the salt
container
contains
a green float
whicha
green floataswhich
descends
as the salt
concentration
the water
drops.
When
descends
the salt
concentration
in the
water drops.inWhen
the green
float
canthe
no
B
green float
canthe
nocontainer
longer be
seen,
the container
be topped
up conwith
longer
be seen,
must
be topped
up with must
regenerating
salt. The
regenerating
salt.atThe
at the
bottom
of the
tainer
is situated
the con-tainer
bottom of is
thesituated
dishwasher.
After
removing
thedishwasher.
lower rack,
After removing
the lowercap
rack,
the
container
cap by turning
it
unscrew
the salt container
(ref. unscrew
A fig. 5-01)
bysalt
turning
it anticlockwise
and pour
anticlockwise
and
in the
using
funnel with
supplied
with the dishwasher.
in
the salt using
thepour
funnel
(ref.salt
A fig.
5-02)the
supplied
the dishwasher.
Before reBefore re-placing
theAcap,
remove
any salt
from from
around
the opening.
placing
the cap (ref.
fig. 5-01),
remove
anyresidues
salt residues
around
the opening.
Fig. 5-03
WITH THE EXCEPTION OF THE SOAK PROGRAM, BEFORE EVERY
WASHING CYCLE IT IS NECESSARY TO ADD THE REQUIRED AMOUNT
OF DETERGENT TO THE DETERGENT DISPENSER. THE RINSE AID,
ON THE OTHER HAND, SHOULD ONLY BE ADDED AS REQUIRED.
A
Fig. 5-01
20
18
16
15
A
EN
USER INSTRUCTIONS
Fig. 5-02
•
•
•
•
•
When using the dishwasher for the first time, in addition to the salt it is also
necessary to add one liter of water to the container.
Each time the salt container is refilled, make sure that the cap (ref. A fig. 5-01)
is securely closed. The mixture of water and detergent must never penetrate
the salt container, as this would compromise the operation of the regeneration
system. In the event of this occurring, the warranty will be invalidated.
Only use regenerating salt specially formulated for domestic dishwashers. If using salt tablets, do not fill the container completely.
Do not use table salt as it contains insoluble substances which, over time, may
damage the water softening system.
When necessary, refill the regenerating salt container before starting the
washing program. In this way, the excess saline solution will be immediately
removed by the water; the prolonged presence of salt water inside the tank
may lead to corrosion.
BE CAREFUL NOT TO CONFUSE THE SALT AND DETERGENT PACKAGES; ADDING DETERGENT TO THE SALT CONTAINER WILL DAMAGE
THE WATER SOFTENING SYSTEM.
21
16
•
•
•
EN
5.2
adjust the water softening system;
add the regenerating
salt; INSTRUCTIONS
USER
USER
INSTRUCTIONS
add the rinse-aid and detergent.
EN
Using the rinse-aid and detergent dispensers
The detergent and rinse aid dispensers are situated on the inner part of the door:
the detergent dispenser (ref. A fig. 5-03) is on the left, and the rinse-aid
dispenser (ref. B fig. 5-03) is on the right.
A
B
Fig. 5-03
WITH THE EXCEPTION OF THE SOAK PROGRAM, BEFORE EVERY
WASHING CYCLE IT IS NECESSARY TO ADD THE REQUIRED AMOUNT
OF DETERGENT TO THE DETERGENT DISPENSER. THE RINSE AID,
ON THE OTHER HAND, SHOULD ONLY BE ADDED AS REQUIRED.
16
20
17
EN
EN
USERINSTRUCTIONS
INSTRUCTIONS
USER
5.2.1
Adding the rinse-aid
The rinse aid helps the dishes dry faster and prevents the formation of scale deposits
and staining; it is automatically added to the water during the final rinse cycle, from
the container situated on the inner side of the door.
B
A
C
Fig. 5-04
To add rinse aid:
• Open the door.
• Rotate the container cover (ref. A fig. 5-04) anticlockwise by ¼ of a turn and remove it.
• Add the rinse aid until the container is full (approximately 140 ml). The optical
level indicator (ref. B fig. 5-04), on the side of the cap should be completely obscured. Refill the rinse aid when the optical level indicator becomes clear again,
or when the rinse aid warning light illuminates (see “Description of controls”
manual).
• Replace the cover (ref. A fig. 5-04) by turning it in a clockwise direction until it is
fully closed.
• Use a cloth to remove any spillage of rinse aid which might lead to the formation
of excess foam.
5.2.2
Adjusting the rinse-aid dispenser setting
The rinse-aid dispenser can be set to one of 6 different levels. The dishwasher is
factory set for medium water hardness (selector set to “3”). To change the setting,
turn the dispenser selector (ref. c fig. 5-04) to the desired position: the amount of
rinse-aid dispensed is proportional to the position of this selector. Make sure that
the minimum amount of rinse-aid (selector turned to “1”) is approximately 1 ml and
the maximum amount (selector turned to “6”) is approximately 6 ml.
18
21
17
EN
EN
USER
USERINSTRUCTIONS
INSTRUCTIONS
•
•
•
•
•
To adjust the rinse aid setting, rotate the dispenser cover (ref. A fig. 5-04) through
a quarter turn in an anticlockwise direction and remove it.
Then use a screwdriver to rotate the rinse aid selector to the desired position.
Replace the cover (ref. A fig. 5-04) by turning it in a clockwise direction until it is
fully closed.
The amount of rinse aid must be increased if the washed dishes appear dull or
feature circular stains.
If, on the other hand, the dishes are sticky or have white streaks, it is necessary to
reduce the rinse aid setting.
5.2.3
Adding the detergent
DO NOT INHALE OR SWALLOW DETERGENT AS THIS MAY CAUSE
BURNS AND/OR PERMANENT DAMAGE TO THE NOSE, MOUTH AND
THROAT, AND EVEN LEADING TO SUFFOCATION; KEEP DETERGENT
AWAY FROM YOUR EYES. IF ONE OF THE ABOVE SITUATIONS OCCURS,
SEEK MEDICAL ASSISTANCE IMMEDIATELY.
PREVENT CHILDREN FROM COMING INTO CONTACT WITH DETERGENT;
KEEP THEM AWAY FROM THE DISHWASHER WHEN THE DOOR IS
OPEN AS IT MAY CONTAIN DETERGENT RESIDUES. FILL THE DISHWASHER JUST BEFORE STARTING THE WASHING CYCLE AND THEN
KEEP THE DETERGENT OUT OF THE REACH OF CHILDREN.
To open the detergent dispenser cover, lightly press the relative button (ref. A fig.
5-05). Add the detergent and close the cover carefully, pushing down on the arrow
(ref. B fig. 5-05). During the washing cycle, the dispenser will be opened automatically.
A
Fig. 5-05
22
18
19
EN
EN
USERINSTRUCTIONS
INSTRUCTIONS
USER
A
B
Fig. 5-06
•
•
•
•
•
•
•
•
20
When a program with hot prewash is selected (see program table in the “Description of Controls” manual), extra detergent must be placed in the cavity (ref.
A or B fig. 5-06, depending on models).
Only use dishwasher-specific detergents. For optimal washing results it is important to use a good quality detergent.
The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results. Once opened the
detergent packs should not be kept for too long, otherwise the detergent loses
its effectiveness.
Do not use detergents formulated for washing dishes by hand, because they
produce a great deal of foam and may negatively affect the operation of the
dishwasher.
Add the correct amount of detergent. An insuffici t amount of detergent will
result in a partial removal of dirt from the dishes, whereas an excessive amount
is wasteful and does not improve the washing results.
The market offers liquid and powder detergents with differing chemical compositions, which may contain phosphates, or be phosphate-free but contain natural enzymes.
Detergents containing phosphates are more effective against grease and starch
at temperatures above 60°C (140°F).
Enzyme detergents, on the other hand, are also effective at lower temperatures
(from 40 to 55°C / from 104 to 131°F) and are more easily biodegradable. With
enzyme detergents it is possible to obtain at low temperatures comparable results to those which can only be achieved at 65°C (149°F) using traditional detergents. For the safeguarding of the environment we recommend the use of
phosphate- and chlorine-free detergents.
23
19
EN
EN
USER
USER
INSTRUCTIONS
USERINSTRUCTIONS
INSTRUCTION
• When using detergent tabs, place them in the cutlery basket. The dispenser
has been designed for powder or liquid detergent. As the cover does not open
completely d uring the washing cycle, t abs are not f ully released ( dissolved).
This could generate the following problems:
rinse cycle.
THE INTRODUCTION O F DETERGENT INTO T HE R INSE A ID D ISPENSER,
EVEN IN LIQUID FORM, WILL DAMA GE THE DISHW ASHER.
5.3
General warnings and recommendations
recommendations concerning dish types to be washed and their loading. There
are generally n o constraints on t he w ashing of domestic d ishes, but i n certain
cases it is necessary to take their characteristics into account. Before loading the
dishes into the racks it is necessary to:
• soak any pots or pans with burnt-on food remains on the bottom to facilitate
removal, then load them into the LOWER RACK.
” option (if available) for washing small amounts of dishes;
Use the “
it saves water and electricity. When using this function, only load the rack se; the other rack must remain empty. There is no need
to pre-wash the dishes under running water before loading them into the racks
since this only wastes water. Correct loading of the dishes helps ensure optimal washing results.
WARNING!
• make sure that the dishes are securely in place so that they cannot tip over or
obstruct the rotation of the spray arms during the washing cycle;
• do not place very small objects in the racks as these could fall and obstruct the
spray arms or the wash pump;
• containers such as cups, bowls, glasses and pots should always be loaded with
the opening facing downwards and with any cavities at an angle, to allow the
water to drain out;
• do not stack dishes or place them in such a way that they cover one other;
• do not place glasses too close together because they may knock against each
other and break, or there might be staining at the point where they touch.
24
20
21
EN
EN
INSTRUCTIONS
USER
USERINSTRUCTIONS
INSTRUCTION
MAKE SURE that the items being washed are dishwasher-safe.
Items which are not dishwasher-safe:
• Wooden dishes, pots or pans: these may be damaged by the high washing
temperatures.
• Handcrafted i tems: these a re r arely suitable for washing in a d ishwasher.
The relatively high water temperatures and the detergents used may damage
them.
• Lightweight objects: place lightweight objects in the upper rack where the
water pressure is lower.
• Dishes and objects in copper, tin, zinc or brass: these tend to stain.
• Aluminum dishes: items made from anodized aluminum may lose their color.
• Silverware: silver items may stain.
• Glass and crystal: in general, glass and crystal objects can be washed in the
dishwasher. However, certain types of glass and crystal may become dull and
lose their clearness after many washings. Therefore, for these items we recommend using the least aggressive program available (see “Description of controls” manual).
• Decorated items: the decorated objects available on the market are generally
able t o withstand washing in t he d ishwasher, although t he c olors may fade
after a great many washes. If in doubt as to the fastness of the colors, it is advisable to wash just a few items at a time for approximately one month.
22
25
21
EN
USER INSTRUCTIONS
5.4
Using the racks
The dishwasher has a capacity of 10 place-settings, including serving dishes.
Examples of loading 10 place-settings in the upper rack (see fig. 5-07) and
in the lower rack (see fig. 5-08) are shown below; move the upper rack to its
bottom position when loading in this way.
Fig. 5-07
Fig. 5-08
23
EN
USER INSTRUCTIONS
5.4.1
Lower rack
The lower rack receives the full force of the lower spray arm, and should therefore be used for the “toughest” items with a heavier degree of soiling.
All types and combinations of loads are permitted, provided that the dishes,
pots and pans are arranged with all the soiled surfaces exposed to the water
jets coming from the bottom.
To make the most of the space inside the rack when loading large items, certain models are equipped with tip-up supports for plates in 2 or 4 sections (see
fig. 5-09).
Withsupporti
fixed supports
Con
fissi
tilting reclinabili
supports
ConWith
supporti
Fig. 5-09
24
EN
USER INSTRUCTIONS
Loading the lower rack (see fig. 5-10)
Carefully load flat plates, soup plates, dessert and serving dishes, positioning them vertically. Pots, pans and their covers must be loaded upside down.
When loading soup plates and dessert bowls, be sure to leave a gap between
them.
Loading
examples:
Esempi
di caricamento:
Fig. 5-10
25
EN
USER INSTRUCTIONS
5.4.2
Cutlery basket (see fig. 5-11)
The cutlery basket can be removed to simplify unloading.
Arrange the cutlery in an orderly manner inside the basket, with the handles
pointing downwards and taking care not to injure yourself with the knife
blades. The basket is suitable for all types of cutlery, except those long enough
to interfere with the upper spray arm.
Place long items (ladles, wooden spoons and cooking knives) that may interfere with the spray arm in the upper rack making sure that knife tips do
not protrude.
The dishwasher is complete with two cutlery baskets, which means that one
of them can be removed, freeing space in the bottom rack, if there is not much
cutlery to be washed.
The baskets feature an exclusive system of independent sliding tip-up supports, offering a choice of combinations to allow optimum use of the space
available.
Inserto
Horizontal
orizzontale
insert
closed
chiuso
Verticalverticali
inserts
Inserti
Inserto
Horizontal
orizzontale
insert
open
aperto
Movement
required
Movimento
per
to extract the inserts
l'estrazione degli
inserti
Fig. 5
5-11
26
EN
USER INSTRUCTIONS
5.4.3
Upper rack (vedi fig. 5-12, 5-13)
It is recommended to load the upper rack with small- or medium-sized items
such as glasses, small plates, tea or coffee cups, shallow bowls and light
objects made from heat resistant plastic.
If the upper rack is used in the lowermost position, it can also be loaded with
serving dishes, provided they are only slightly soiled.
The two tip-up “cutlery baskets” on the right-hand side of the rack can be opened or closed as required (see fig. 5-12). The two cup supports on the left-hand
side of the rack can be opened or closed as required (see fig. 5.13).
Fig. 5-12
Fig. 5-13
27
EN
USER INSTRUCTIONS
Loading the upper rack (vedi fig. 5-14)
Load platesthe
facing
forward;
cups,
bowls
must always be facing downwarLoading
upper
rack
(vedi
fig.etc.
5-14)
ds. The left-hand side of the rack can be loaded with two layers of cups and
Load plates
forward;
cups,
etc.with
must
always
beside-plates,
facing downwarglasses.
Thefacing
right-hand
side
can bowls
be filled
plates
and
fitted
ds.
The
left-hand
side
of
the
rack
can
be
loaded
with
two
layers
of cups and
upright into the supports provided.
glasses. The right-hand side can be filled with plates and side-plates, fitted
upright into the supports provided.
Loading
examples:
Esempi
di caricamento:
Loading
examples:
Esempi
di caricamento:
ADJUSTING THE UPPER BASKET
Fig. 5-14
The height of the upper basket can be according to requirements and
ADJUSTING
UPPER
Fig. 5-14
the size of theTHE
dishes
in theBASKET
lower basket.
The height
of the upper
basket can be according to requirements and
Pull-out
adjustment
system:
the size of the dishes in the lower basket.
•
Turn the retainer E on both runners, right and left, through 90°
Pull-out adjustment system:
•
Remove the basket
Turnthe
thebasket
retainer
E fit
onthe
both
runners,
right
and left,inthrough
90°
••
Lift
and
smaller
pairs
of wheels
the runners
•
Remove
the
basket
Return the retainers E to their original position
•
Lift the basket and fit the smaller pairs of wheels in the runners
•
Return the retainers E to their original position
28
EN
USER INSTRUCTIONS
Quicklift position setting system:
system with 3 position settings (1 lowest, 3 highest). The basket is
Quicklift position setting system:
snapped into the position required, lifting both sides simultaneously. To
system
with position
3 position
settings
(1 lowest,
highest).
Theto basket
return to the
lowest
from
any height,
lift 3the
basket
the is
snapped into the position required, lifting both sides simultaneously. To
highest position
and then release.
return to the lowest position from any height, lift the basket to the
highest position and then release.
LOWEST
RELEASE
LOWEST
RELEASE
MEDIUMMEDIUM
HIGHEST
HIGHEST
29
EN
EN
USER
INSTRUCTIONS
USER
INSTRUCTIONS
USER
INSTRUCTION
6
6.1
30
33
29
EN
EN
USER
USER
INSTRUCTIONS
USERINSTRUCTIONS
INSTRUCTION
6.2
Cleaning the water intake filter
Clean the water inlet fil er at regular intervals. After closing the delivery tap, unscrew
the ring nut (ref. A fig. 6-01) on the water inlet pipe (using a pair of pliers, if necessary) and delicately clean the fil er, removing deposits or impurities.
Then fi mly fix the pipe by tightening the ring nut (ref. A fig. 6-01) (use a pair of pliers,
if necessary).
Fig. 6-01
6.3
Cleaning the spray arms
The spray arms can be easily removed for periodic cleaning of the nozzles, to prevent possible clogging. Wash them under running water (at room temperature) and
carefully replace them in their seats, checking that their rotary movement is in no
way impeded; if this is not the case, make sure they have been mounted properly.
Removing the spray arms
• To remove the upper spray arm (ref. A fig. 6-02), unscrew the locking ring (ref. R
B
fig. 6-02) by turning it clockwise. After cleaning, remount the spray arm in its seat
and tighten the locking ring by turning it anti-clockwise.
• To remove the orbital spray arm assembly (ref. A fig. 6-03), take hold of the lower
arm (ref. B fig. 6-03) and pull the orbital unit upward (see fig. 6-03).
After cleaning, remount the orbital spray arm in its seat and push it down slightly until it clicks into place on the lower spray arm (see fig. 6-03). Then remount the lower
spray arm into its seat and push it down slightly until it click into place (see fig. 6-03).
34
30
31
EN
WARNINGS
User instructions
User instructions
CLEANING THE OSCILLATING BOTTOM SPRAY ARM
● Take hold
of the bottom
spray armBOTTOM
unit andSPRAY
pull it upward
to release.
CLEANING
THE OSCILLATING
ARM
● Take hold of the bottom spray arm unit and pull it upward to release.
● Separate the oscillating arm A from the spray arm B.
● Separate
the oscillating
arm A from
thetospray
arm B.the toothed wheel C
● Turn the
oscillating
arm A upside
down
release
● Turn
oscillating
A upside
down
to release the toothed wheel C
by pressing
thethe
teeth
D andarm
turning
them
anticlockwise.
by pressing the teeth D and turning them anticlockwise.
● Extract●the
wheel C and wash all components under running water.
Extract the wheel C and wash all components under running water.
AssembleAssemble
the spray
arm arm
unit unit
by byreversing
sequence
described
the spray
reversing the
the sequence
described
above. above.
The wheel
can only
mountedin
in one
one position;
thethe
teeth
D
Warning:Warning:
The wheel
C canC only
be be
mounted
position;
teeth
D
must engage properly.
must engage
properly.
Fit the unit so that the wheel C is facing towards the door of the
Fit the unit
so that the wheel C is facing towards the door of the
dishwasher.
dishwasher.
32
26
EN
EN
WARNINGS
USER
USERINSTRUCTIONS
INSTRUCTION
6.4
CLEANING THE FILTER UNIT
5.4
6-04
Cleaning the filter unit
•
The central filter should be cleaned regularly. To remove it, pull the
• Periodically
theupwards.
filter 6-05
unit (ref. A fig. 5-04) and, if necessary, clean it
spray arm inspect
assembly
under
running
water
(at
room
temperature),
usingand
a stiff
brush.
remove
•
Turn the microfilter M anticlockwise
to release
extract
it, To
then
lift
the
grip the
tabs,
turn
thefilter,
stainless
steel
filter
F.anticlockwise and lift upwards;
• push the centre filter (ref. A fig. 5-05) from the underside to remove it from
•
Push the central filter H from below to extract it from the
micro-filter.
6-05
the micro-filter;
•• separate
Separatethethe
two
parts
of
the
plastic
filter
by
pressing
the by
body
of
two parts which make up the plastic centre filter
pressing
the
filter
in
the
zone
shown
by
the
arrows.
the body of the filter in the zone shown by the arrows (ref. B fig. 5-05);
•• remove
Remove
central
by lifting
it.
thethe
centre
filterfilter
by lifting
it upwards.
6-05
6-04 the
• after cleaning, remount the filter unit, joining the two parts comprising
centre filter by pushing slightly until they click into place; insert the centre
filter into the micro-filter (see fig. 5-05). Reposition the filter unit (ref. A fig.
5-04) into its seat, turning it clockwise until it locks.
Fig. 6-04
Fig. 5-04
B
B
A
Fig. 5-05
Fig. 6-05
36
32
33
EN
EN
WARNINGS
USER
INSTRUCTIONS
USER
INSTRUCTION
6.5
34
37
33
EN
EN
WARNINGS
USERWARNINGS
INSTRUCTION
6.6
38
34
35
EN
EN
WARNINGS
USERWARNINGS
INSTRUCTION
36
39
35
EN
EN
WARNINGS
7
IMPORTANT SAFETY INSTRUCTION
(Save this instructions)
THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT
MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER.
BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL.
INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN,
IN COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE
IS INTENDED FOR DOMESTIC USE AND SIMILAR APPLICATIONS SUCH
AS THE STAFF KITCHENS OF SHOPS, OFFICES AND OTHER WORKPLACES, INSTITUTIONS, AND FOR THE USE OF GUESTS AT HOTELS,
HOSTELS, BED AND BREAKFAST ESTABLISHMENTS AND OTHER RESIDENTIAL FACILITIES AND COMPLIES WITH DIRECTIVES 2006/95/EC
AND 2004/108/EC CURRENTLY IN FORCE, INCLUDING THE PREVENTION AND ELIMINATION OF RADIO FREQUENCY INTERFERENCE.
THE APPLIANCE IS DESIGNED FOR THE FOLLOWING PURPOSE:
WASHING AND DRYING OF DISHES; ANY OTHER USE SHALL BE
CONSIDERED IMPROPER. THE MANUFACTURER DECLINES ALL
RESPONSIBILITY FOR USES OTHER THAN THOSE DESCRIBED
ABOVE.
THE NAME PLATE FEATURING THE TECHNICAL DATA, SERIAL NUMBER
AND MARKINGS IS VISIBLY POSITIONED ON THE INNER EDGE OF THE
DOOR. THE NAME PLATE MUST NEVER BE REMOVED.
THIS APPLIANCE IS NOT SUITABLE FOR USE ON BOATS, CARAVANS OR
THE LIKE.
DISHWASHERS CERTIFIED FOR DOMESTIC USE ARE NOT SUITABLE
FOR AUTHORISED FOOD FACTORIES.
CHECK THAT THE VOLTAGE, FREQUENCY AND PROTECTION OF THE
DOMESTIC MAINS POWER SUPPLY MATCH THE RATINGS ON THE
NAME PLATE OF THE APPLIANCE.
DO NOT LEAVING DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS PACKAGING
MATERIALS AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE. KEEP CHILDREN, PHYSICALLY AND/OR MENTALLY
IMPAIRED ADULTS, AND ANIMALS AWAY FROM PACKAGING WASTE;
DANGER OF SUFFOCATION.
40
36
37
EN
EN
WARNINGS
WARNINGS
BEFORE PROCEEDING WITH INSTALLATION, DISCONNECT THE MAINS
POWER SUPPLY FROM THE WORK AREA.
DO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR
BURNING WITH CONSEQUENT FIRE HAZARD.
DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON
THE SHARP EDGES OF THE APPLIANCE; WEAR SAFETY GLOVES.
THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION IN ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN FORCE.
IF IN DOUBT, HAVE THE SYSTEM CHECKED BY A QUALIFIED ELECTRICIAN (SEE ALSO THE WARNINGS INDICATED IN CHAPTER 3).
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS OR PROPERTY RESULTING FROM THE FAILURE
TO EARTH THE APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION.
ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO
AVOID WASTING ELECTRICITY.
IN THE EVENT OF A FAULT, DISCONNECT THE DISHWASHER FROM
THE ELECTRICAL POWER SUPPLY AND SHUT OFF THE WATER TAP.
DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING
TRANSIT! IF IN DOUBT, CONSULT YOUR DEALER. THE APPLIANCE
MUST BE INSTALLED AND CONNECTED IN ACCORDANCE WITH
THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OR BY A
QUALIFIED TECHNICIAN.
ONLY USE DETERGENTS SPECIALLY FORMULATED FOR DISHWASHERS.
DO NOT USE DETERGENTS FORMULATED FOR WASHING DISHES
BY HAND.
ONLY USE RINSE”AID SPECIALLY FORMULATED FOR DOMESTIC
DISHWASHERS.
38
41
37
EN
EN
WARNINGS
DO NOT INHALE OR SWALLOW DETERGENT AS THIS MAY CAUSE
BURNS AND/OR PERMANENT DAMAGE TO THE NOSE, MOUTH AND
THROAT, AND EVEN LEADING TO SUFFOCATION; KEEP DETERGENT
AWAY FROM YOUR EYES. IF ONE OF THE ABOVE SITUATIONS OCCURS,
SEEK MEDICAL ASSISTANCE IMMEDIATELY.
TO PREVENT CHILDREN FROM COMING INTO CONTACT WITH DETERGENT, FILL THE DISHWASHER JUST BEFORE STARTING THE WORK
PROGRAM AND THEN KEEP THE DETERGENT OUT OF THE REACH OF
CHILDREN.
THIS DISHWASHER MUST BE USED BY ADULTS. USE BY PERSONS WITH
REDUCED MENTAL AND/OR PHYSICAL CAPABILITIES IS ONLY PERMITTED UNDER THE SUPERVISION OF A PERSON RESPONSIBLE FOR
THEIR SAFETY.
DO NOT ALLOW CHILDREN TO APPROACH AND/OR PLAY IN OR ON
THE DISHWASHER. THE APPLIANCE MAY CONTAIN RESIDUES OF DETERGENT WHICH CAN CAUSE PERMANENT DAMAGE TO THE EYES,
MOUTH AND THROAT, AS WELL AS POSSIBLE DEATH BY SUFFOCATION; IF THE ABOVE OCCURS, SEEK MEDICAL ASSISTANCE IMMEDIATELY.
BEWARE; IT IS POSSIBLE FOR CHILDREN TO GET TRAPPED INSIDE THE
DISHWASHER!
DO NOT INTRODUCE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE
WHICH MAY CAUSE AN EXPLOSION.
DO NOT POUR POWDER AND/OR LIQUID DETERGENT INTO THE
RINSEAID CONTAINER AS THIS WILL DAMAGE THE CONTAINER.
DO NOT POUR POWDER AND/OR LIQUID DETERGENT INTO THE
WASTER SOFTENER TANK AS THIS WILL DAMAGE THE TANK.
DO NOT USE INDUSTRIAL DETERGENTS AS THIS MAY DAMAGE
THE APPLIANCE AND/OR TRIGGER VIOLENT CHEMICAL REACTIONS (E.G. EXPLOSIVE GAS).
DO NOT LOAD DISHES THAT ARE SOILED WITH ASH, WAX OR
PAINTS.
DO NOT INTRODUCE ITEMS IN HEAT-SENSITIVE PLASTIC, SUCH AS
DISPOSABLE CUTLERY OR PLATES, AS THESE MAY BECOME DEFORMED. DO NOT WASH OBJECTS IN PLASTIC UNLESS THEY ARE
MARKED “DISHWASHER PROOF” OR THE LIKE. FOR UNMARKED
OBJECTS, FOLLOW THE INSTRUCTIONS OF THE MANUFACTURER;
IF NO INFORMATION IS AVAILABLE, DO NOT WASH THESE OBJECTS IN THE DISHWASHER.
42
38
39
EN
EN
WARNINGS
WARNINGS
DO NOT INTRODUCE ANIMALS INTO THE DISHWASHER.
WHEN OPENING THE DISHWASHER DOOR DURING A CYCLE THERE IS
A RISK OF SCALDING DUE TO THE HEAT CONTAINED INSIDE; DO NOT
GET IN THE WAY OF THE STEAM LEAVING THE APPLIANCE AND DO
NOT TOUCH THE COMPONENTS INSIDE.
WAIT 20 MINUTES AFTER THE END OF THE WASHING CYCLE OR AFTER
INTERRUPTING IT BEFORE REMOVING THE DISHES IN ORDER TO ALLOW THEM TO DRY.
IN CERTAIN SITUATIONS, HYDROGEN MAY BE GENERATED INSIDE
A HOT WATER SYSTEM THAT HAS NOT BEEN USED FOR OVER TWO
WEEKS.
HYDROGEN IS AN EXPLOSIVE GAS. IF THE HOT WATER SYSTEM
HAS NOT BEEN USED FOR TWO WEEKS OR MORE, OPEN ALL THE HOT
WATER TAPS AND ALLOW THE WATER TO RUN FOR A FEW MINUTES
BEFORE USING THE DISHWASHER. THIS WILL DISCHARGE ANY HYDROGEN BUILDUPS. AS THIS GAS IS FLAMMABLE, DO NOT SMOKE
OR USE NAKED FLAMES WHILE PERFORMING THIS OPERATION.
LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN
MAY CAUSE THE APPLIANCE TO OVERTURN, PUTTING PEOPLE
AT RISK. NEVER LEAVE THE DISHWASHER DOOR OPEN; PEOPLE
MIGHT TRIP OVER IT.
DO NOT LEAN AGAINST OR STAND ON THE DISHWASHER RACKS.
DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER.
KNIVES OR OTHER SHARP”ENDED COOKING UTENSILS MUST BE
PLACED IN THE CUTLERY BASKET BLADE”DOWN, OR LAID HORIZONTAL IN THE UPPER RACK. TAKE CARE NOT TO CUT YOURSELF AND ENSURE THAT THEY DO NOT PROJECT FROM THE RACK.
POSITION SHARP/POINTED OBJECTS SO AS TO PREVENT THEM FROM
DAMAGING THE DOOR GASKETS.
DO NOT OPERATE THE DISHWASHER UNLESS ALL THE OUTER PANELS
HAVE BEEN POSITIONED CORRECTLY.
DO NOT TAMPER WITH THE DISHWASHER CONTROLS.
40
43
39
EN
EN
USER INSTRUCTIONS
WARNINGS
AQUASTOP MODELS; THE AQUASTOP DEVICE PREVENTS FLOODING IN THE EVENT OF A WATER LEAK. WHEN THE AQUASTOP DEVICE
IS TRIPPED (THE ERROR IS INDICATED ON THE DISPLAY), CALL IN A
QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT. IN
MODELS EQUIPPED WITH THE AQUASTOP DEVICE, THERE IS A SOLENOID VALVE INSIDE THE WATER INTAKE HOSE. DO NOT CUT THE
HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP
INTO WATER. IN THE EVENT OF DAMAGE TO THE WATER INTAKE
HOSE, DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER
SUPPLY AND FROM THE WATER SUPPLY.
IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM A
QUICK TEST OF THE APPLIANCE (SEE “INSTALLATION” MANUAL).
IF THE DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT
IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST
TECHNICAL SERVICE CENTRE. DO NOT ATTEMPT TO REPAIR THE
APPLIANCE.
THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE
REGULATIONS IN FORCE CONCERNING SAFETY AND ELECTRICAL
EQUIPMENT. ANY TECHNICAL CHECKS SHOULD BE CONDUCTED EXCLUSIVELY BY A TRAINED AND AUTHORIZED TECHNICIAN: REPAIRS
CARRIED OUT BY UNAUTHORIZED PERSONS WILL INVALIDATE
THE WARRANTY, AS WELL AS POSING A POTENTIAL HAZARD TO
THE USER.
BEFORE CLEANING OR SERVICING THE APPLIANCE, REMOVE THE
PLUG OR TURN OFF THE MULTI-POLE SWITCH.
REMOVE THE WASHING COMPARTMENT DOOR AND DISCONNECT THE MAINS POWER SUPPLY WHEN REMOVING THE OLD
DISHWASHER FOR MAINTENANCE OR DISPOSAL.
THE SYMBOL
ON THE PRODUCT, OR ON THE DOCUMENTS ACCOMPANYING THE PRODUCT, INDICATES THAT THIS APPLIANCE
MAY NOT BE TREATED AS HOUSEHOLD WASTE. INSTEAD IT SHALL
BE HANDED OVER TO THE APPLICABLE COLLECTION POINT FOR
THE RECYCLING OF ELECTRICAL AND ELECTRONIC EQUIPMENT.
DISPOSAL MUST BE CARRIED OUT IN ACCORDANCE WITH LOCAL ENVIRONMENTAL REGULATIONS FOR WASTE DISPOSAL. FOR
MORE DETAILED INFORMATION ABOUT TREATMENT, RECOVERY
AND RECYCLING OF THIS PRODUCT, PLEASE CONTACT YOUR LOCAL CITY OFFICE, YOUR HOUSEHOLD WASTE DISPOSAL SERVICE
OR THE SHOP WHERE YOU PURCHASED THE PRODUCT.
44
40
41
EN
EN
USER
INSTRUCTIONS
WARNINGS
BY ENSURING THIS PRODUCT IS DISPOSED OF CORRECTLY, YOU WILL
HELP PREVENT POTENTIAL NEGATIVE CONSEQUENCES FOR THE ENVIRONMENT AND HUMAN HEALTH.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR
DAMAGE TO PERSONS, ANIMALS OR PROPERTY RESULTING
FROM FAILURE TO OBSERVE THE ABOVE PRECAUTIONS, FROM
TAMPERING WITH EVEN A SINGLE COMPONENT OF THE APPLIANCE, OR FROM THE USE OF UNORIGINAL SPARE PARTS.
IF IN DOUBT ABOUT THE CONTENTS OF THIS MANUAL, CONTACT THE TECHNICAL ASSISTANCE SERVICE.
DO NOT USE STEAM CLEANERS TO CLEAN THE DISHWASHER.
WARNING: SOME DISHWASHER DETERGENTS ARE STRONGLY ALKALINE. THEY CAN BE EXTREMELY DANGEROUS IF SWALLOWED. AVOID
CONTACT WITH THE SKIN AND EYES AND KEEP CHILDREN AWAY
FROM THE DISHWASHER WHEN THE DOOR IS OPEN. CHECK THAT
THE DETERGENT RECEPTACLE IS EMPTY AFTER COMPLETION OF THE
WASH CYCLE.
42
45
41
EN
EN
USER
USERINSTRUCTIONS
INSTRUCTIONS
INSTALLATION
INSTRUCTIONS
8
INSTALLATION AND HOOK-UP
To install and hook up this appliance, consult the attached installation manual.
Bear in mind the following warnings when installing and hooking up the dishwasher.
DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON
THE SHARP EDGES OF THE APPLIANCE; WEAR SAFETY GLOVES.
INSTALLATION, REPAIRS AND SERVICING MUST BE PERFORMED
BY QUALIFIED AND AUTHORIZED TECHNICIANS. AS WELL AS INVALIDATING THE WARRANTY, WORK CARRIED OUT BY UNAUTHORIZED PERSONS MAY GENERATE HAZARDS. INSTALLATION MUST BE
PERFORMED IN COMPLIANCE WITH ALL THE DIRECTIVES IN FORCE
IN THE COUNTRY OF INSTALLATION AND, IF THESE DO NOT EXIST: IN
THE UNITED STATES THE NATIONAL ELECTRIC CODE; IN CANADA THE
CANADIAN ELECTRIC CODE C22.1 - LATEST EDITION/PROVINCIAL
AND MUNICIPAL CODES AND/OR LOCAL CODES.
BUILDING-IN A DISHWASHER UNDERNEATH A CERAMIC HOB IS ABSOLUTELY FORBIDDEN. A DISHWASHER CAN BE BUILT-IN UNDERNEATH A CONVENTIONAL HOB PROVIDED THERE IS NO BREAK IN
THE KITCHEN WORKTOP, AND THE DISHWASHER AND HOB ARE INSTALLED AND SECURED CORRECTLY, SO THAT NO HAZARDS ARE
GENERATED.
PREVENTING THE RISK OF CLOGGING OR DAMAGE: IF THE WATER PIPE IS NEW OR HAS NOT BEEN USED FOR A LONG TIME, BEFORE
CONNECTING TO THE WATER SUPPLY CHECK THAT THE WATER IS
CLEAR AND FREE OF IMPURITIES, TO PREVENT DAMAGE TO THE APPLIANCE. THE DISHWASHER MUST ALWAYS BE CONNECTED TO
THE WATER SYSTEM WITH NEW HOSES; OLD OR USED HOSES
MUST NEVER BE REUSED.
CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS
MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR.
IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL
SERVICE CENTRE.
THIS APPLIANCE MUST BE EARTHED. IN CASE OF A MALFUNCTION OF
FAULT, THE EARTH REDUCES THE RISK OF ELECTROCUTION BY PROVIDING THE ELECTRICAL CURRENT WITH AN ALTERNATIVE, LESS RESISTANT PATH.
46
42
43
USER
INSTALLATION
INSTRUCTIONS
USERINSTRUCTIONS
INSTRUCTIONS
EN
ENEN
BEFORE MAKING ELECTRICAL CONNECTIONS, DISCONNECT THE
MAINS POWER SUPPLY FROM THE WORK AREA.
CHECK THAT THE MAINS SUPPLY IN THE PLACE OF INSTALLATION
COMPLIES WITH THE REGULATIONS IN FORCE IN THE COUNTRY OF
USE, AND THAT IT IS CORRECTLY EARTHED.
THIS APPLIANCE MUST BE EARTHED. IN CASE OF A MALFUNCTION OF
FAULT, THE EARTH REDUCES THE RISK OF ELECTROCUTION BY PROVIDING THE ELECTRICAL CURRENT WITH AN ALTERNATIVE, LESS
RESISTANT PATH. THIS APPLIANCE IS FITTED WITH A SUPPLY CORD
CONTAINING AN EARTH WIRE AND PLUG. FIT THE PLUG INTO A SUITABLE SOCKET, INSTALLED AND EARTHED IN COMPLIANCE WITH THE
LAWS IN FORCE IN THE COUNTRY OF INSTALLATION.
AN INCORRECTLY CONNECTED EARTH WIRE MAY GENERATE THE RISK
OF ELECTROCUTION. IF IN DOUBT AS TO THE CORRECT EARTHING OF
THE APPLIANCE, CALL IN A QUALIFIED ELECTRICIAN OR THE TECHNICAL ASSISTANCE SERVICE. DO NOT CHANGE THE PLUG ATTACHED
TO THE APPLIANCE. IF THE PLUG IS NOT SUITABLE FOR THE SOCKET,
CALL IN A QUALIFIED ELECTRICIAN TO FIT A SUITABLE PLUG.
IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED
BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE
CENTRE IN ORDER TO AVOID ANY RISK.
DO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR
BURNING, WITH CONSEQUENT FIRE HAZARD.
44
43 47
EN
EN
USER
INSTRUCTIONS
USERINSTRUCTIONS
INSTRUCTION
USER
9
9-01
44.7 cm - 44.9 cm (17-19/32”; 17-43/64”)
from 82 cm to 87 cm (from 32-9/32” to 34-1/4”)
10
Tab. 9-01
48
44
45
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising