Fisher Paykel | CMOH30SS2Y | Installation instructions | Fisher Paykel CMOH30SS2Y Installation Instructions

Fisher Paykel CMOH30SS2Y Installation Instructions
OVER THE RANGE CONVECTION MICROWAVE OVEN
INSTALLATION INSTRUCTIONS
Please read all instructions thoroughly before installing the Over the Range Microwave Oven/Hood System.
Two people are recommended to install this product.
If a new electrical outlet is required, its installation should be completed by a qualified electrician before
the microwave oven is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.
1. MOUNTING SPACE
This Microwave Oven/Hood requires a mounting space on
a wall as shown in Figure 1.
For proper installation and servicing, a 2-inch space is necessary
between the top of the range backsplash and the bottom of
the Microwave Oven/Hood system.
2. WALL CONSTRUCTION
12"
30"
15.5"
Minimum 2"
Backsplash
This Microwave Oven/Hood should be mounted against and
supported by a at vertical wall. T
installation. If the wall is not
Wall construction should be a minimum of 2" x 4" wood studding
and 3/8" or more thick dry wall or plaster/lath. The mounting
surfaces must be capable of supporting weight of 110 pounds
—the oven and contents—AND the weight of all items which
would normally be stored in the top cabinet above the unit.
36" or more
from cooking
surface
72" or more
The unit should be attached to a minimum of one 2" x 4"
wall stud.
To
may be used:
A. Use a stud finder, a magnetic device which locates the nails
in the stud.
Figure 1
16" or 24"
2"x 4"
Wood Studs
B. Use a hammer to tap lightly across the mounting surface
to find a solid sound. This will indicate stud location.
The center of the stud can be located by probing the wall with
a small nail to find the edges of the stud and then placing a
mark halfway between the edges. The center of any adjacent
studs will normally be 16" or 24" to either side of this mark.
Note: In the event that the unit will be unable to be supported
by any stud, it will be necessary to use special care in the
placement of the toggle bolts and top cabinet screws.
See Wall Template for details. The top cabinet should be tested
to ensure it is securely attached to the wall. Place extra weight
up to 110 pounds inside the top cabinet to test the support.
3/8" Dry Wall
or Plaster/lath
Figure 2
1
3. ELECTRICAL GROUNDING INSTRUCTIONS
This appliance must be grounded. This microwave oven is equipped with a cord having a grounding wire
with a grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded
in accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces risk of electric shock
by providing an escape wire for the electric current.
WARNING – Improper use of the grounding plug can result in
a risk of electric shock. DO NOT USE AN EXTENSION CORD.
If the power supply cord is too short, have a qualified electrician
or service person install an outlet near the appliance.
The microwave oven is equipped with a 3-prong grounding plug. DO NOT UNDER
ANY CIRCUMSTANCES CUT OR REMOVE THE GROUNDING PIN FROM THE PLUG.
The Power Supply Cord and plug must be connected to a
separate 120 Volt AC, 60 Hz, 15 Amp, or more branch circuit,
single grounded receptacle. The receptacle should be
located inside the cabinet directly above the Microwave
Oven/Hood mount-ing location.
Ground
Receptacle
Notes:
Opening for Power
Cord
1. If you have any questions about the grounding or electrical
instructions, consult a qualified electrician or serviceperson.
2. Neither Fisher & Paykel nor the dealer can accept any
liability for damage to the oven or personal injury resulting
from failure to observe the correct electrical connection
procedures.
Figure 3
4. HOOD EXHAUST DUCT
When the hood is vented to the outside, a hood exhaust duct is required. All ductwork must be metal; absolutely do not use plastic duct. Check that all connections are made securely. Please read the following carefully:
EXHAUST CONNECTION: The hood exhaust has been designed to connect to a standard 3-1/4" x 10"
rectangular duct. If round duct is required, a rectangular-to-round adapter must be used.
REAR EXHAUST: If a rear or horizontal exhaust
is to be used, care should be taken to align the
exhaust with the space between the studs, or wall
should be prepared at the time it is constructed
by leaving enough space between wall studs to
accommodate exhaust.
Maximum duct length: For satisfactory air
movement, the total duct length of 3-1/4" x 10"
rectangular or 6" diameter round duct should not
exceed 140 feet.
Figure 4
Elbows, adapters, wall, roof caps, etc. present additional resistance to air flow and are equivalent to a section
of straight duct which is longer than their actual physical size. When calculating the total length, add the
equivalent lengths of all transitions and adapters plus the length of all straight duct sections. Figure 4 shows
the approximate feet of equivalent length of some typical ductwork parts. Use the values in parentheses for
calculating air flow resistance equivalent, which should total less than 140 feet.
2
5. TOOLS RECOMMENDED FOR INSTALLATION
• Phillips Screwdriver
• 1-1/2" Wood Bit or Metal Hole Cutter (if metal cabinet is used)
• Electric Drill
• 1/2", 5/8" and 3/32" Drill Bits
• Scissors
• Saw to cut exhaust opening (if needed)
• Pencil
• Measure
• Tape
• Protective Drop Cloth for product and range—you may also
use carton for protection
6. INSTALLATION HARDWARE
The INSTALLATION HARDWARE (items 1-8) packed with the oven should contain the following:
ITEM
1
6
Quantity
Part code
1
Wood Screw 5 x 30 mm
6
290109
2
Toggle Bolt #10 - 24 x 50 mm
4
290106
3
Top Cabinet Screw 5 x 60 mm
2
290108
4
Flat Washer 30 mm diameter
2
290107
5
Grommet
1
290105
6
Tapping Screw 4 x 12 mm
8
245657
7
Exhaust Damper Assembly
1
290046
8
Mounting Deflector
1
290122
2
7
Name
3
4
5
8
Figure 5
7. preparation of the oven
1. Open the bottom of the carton, remove oven and all packing materials.
2. CHECK THE OVEN.
Check the oven for any damage, such as misaligned or bent door,
damaged door seals and sealing surfaces, broken or loose door
hinges and latches and dents inside the cavity or on the door.
If there is any damage, do not operate the oven and contact
your dealer or Fisher & Paykel AUTHORIZED SERVICER.
3. Rest the microwave oven on its side as shown in Figure 6.
4. Remove the two screws which secure the mounting plate
to the rear side of the oven. Remove the mounting plate.
The two screws can be discarded.
Note: If the unit you purchased does not have the mounting
plate attached to the rear side of the oven, please disregard
this section and continue to Section 8.
Mounting plate
Grease filter openings
Figure 6
3
8. Ventilation system
This Microwave Oven/Hood System is designed for
adaptation to three types of hood ventilation systems.
Select the configuration required for your installation.
Fan Cover Bracket
A. Recirculating - Non-Vented,
ductless Operation
The unit is shipped assembled for recirculating.
Notes:
Figure 7
1. The Exhaust Damper Assembly (Figure 11) is not
required for recirculating operation.
2. The Charcoal Filter, located behind the hood exhaust
louver, should be replaced every 6 to 12 months,
depending on use.
B. Horizontal Exhaust — Outside Ventilation
1. Remove and save the 4 screws from Fan Cover Bracket.
Remove Fan Cover Bracket by sliding it in the opposite
direction of the arrow on the Fan Cover Bracket, as
shown in Figure 7.
2. Lift Hood Fan Unit carefully and slip wires out of cavity.
See Figure 8.
Figure 8
(A) Rotate 180˚
(B)
CAUTION: Do not pull or stretch hood fan wiring.
3. Rotate the Hood Fan Unit 180˚ so that the fan blade
openings are facing the back of the oven.
Note, you will need to lift the wire over the hood
fan unit so the wire will clear. See Figure 9 (A).
Replace Hood Fan Unit into the oven. Be careful not to
pinch the wire and the Hood Fan Unit. See Figure 9 (B).
Figure 9
4. Put the wire back into the cavity.
5. Replace the fan cover bracket. Make sure the fan
blades are visible through the rear openings in oven
before proceeding. Attach the fan cover bracket to
the unit with the 4 screws removed in step 1 above.
See Figure 10. The hood fan is now rotated for
horizontal exhaust operation.
6. Attach the Exhaust Damper Assembly to the back
of the mounting plate by sliding it into the slits
in the same direction as the arrow. See Figure 11.
Using tapping screw 4 x 12 mm from the INSTALLATION
HARDWARE, tighten into place.
Wire Box
Figure 10
Mounting Plate (back side)
Figure 11
4
C. Vertical Exhaust — Outside Ventilation
1. Remove and save the 4 screws from the Fan Cover Bracket. Remove Fan Cover Bracket by sliding it in the
opposite direction of the arrow on the Fan Cover Bracket as shown in Figure 12.
2. Lift the Hood Fan Unit carefully and slip wires out of cavity. See Figure 13.
CAUTION: Do not pull or stretch hood fan wiring.
3. Rotate the Hood Fan Unit 180˚ so that the fan blade openings are facing the back of the oven.
Note, you will need to lift the wire over the hood fan unit so the wire will clear. See Figure 14 (A).
Then rotate the Hood Fan Unit 90˚ so that the fan blade openings are facing the top of the oven.
See Figure 14 (B). Replace Hood Fan Unit into the oven. Be careful not to pinch the lead wire between
the inner bracket and the Hood Fan Unit. Put the lead wire into Wire Box. See Figure 14 (C).
4. Replace the Fan Cover Bracket. Make sure the fan blades are visible through the top openings in the
oven before proceeding.
5. Attach the Fan Cover Bracket to unit with the 4 screws removed in step 1 above. See Figure 15.
The Hood Fan Unit is now rotated for vertical exhaust operation.
6. Attach the Exhaust Damper Assembly to the fan cover on the top of the outer case cabinet by sliding it
into the slits in the same direction as the arrow. Use 1 Tapping Screw 4 x 12 mm from the INSTALLATION
HARDWARE and tighten into place. See Figure 16.
Fan Cover Bracket
Figure 12
Figure 13
(A) Rotate 180˚
(C)
(B)
Wire Box
Figure 14
Figure 15
Exhaust Damper Assembly
Figure 16
5
9. OVEN INSTALLATION
THIS MICROWAVE OVEN CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO THE MOUNTING
INSTRUCTIONS FOUND ON BOTH TEMPLATES.
READ AND FOLLOW MOUNTING INFORMATION ON BOTH TOP CABINET AND WALL TEMPLATES.
MOUNTING PLATE
1. Separate 4 Toggle Bolts 2, packed in the INSTALLATION
HARDWARE, from the Toggle Nuts.
2. Use Wood Screws 1 to attach Mounting Plate to the stud or studs.
Use Toggle Bolts to attach Mounting Plate through the holes at
A, B, C and D; UNLESS THOSE HOLES ARE LOCATED ON THE STUD.
Insert one Toggle Bolt into A, B, C and D where appropriate
(these correspond to the holes of the Wall Template) and put the
Toggle Nuts onto the Toggle Bolts. Figure 17.
Refer to instructions in Wall Template.
Mounting Plate
Figure 17
Space more than
wall thickness
3. Position the Mounting Plate with the Toggle Bolts attached at the
wall location and insert Toggle Nuts and Bolts through the holes in
the wall with the Toggle Nuts closed. Figure 18. Use Wood Screws
1 to attach the Mounting Plate to studs.
Note: Before insertion, be sure you leave a space more than the
thickness of the wall between the Mounting Plate and the end
of each of the Toggle Nuts (in the closed position). If you do not
leave enough space, the Toggle Nut will not be able to open on the
other side of the wall. Also, once a Toggle Nut opens, it cannot be
with-drawn from the hole; therefore make sure all of the Toggles
are in the correct position before insertion.
Wall
Figure 18
4. Align the Mounting Plate carefully and hold in position while
tightening Toggle Bolts. Pull Toggle Bolt toward you and turn
clockwise to tighten. Figure 19.
Figure 19
6
MOUNTING OVEN TO THE WALL
Two people are recommended to attach the Microwave Oven/Hood to the Mounting Plate.
1. Thread the power supply cord through the hole
made in the bottom of the top cabinet.
2. Hang the oven on the lower edge of the
mounting plate. Rotate the unit upward.
See Figure 20. Take care that the power
cord is able to clear the edge of the hole
as the oven is rotated upward. (In the case
of a non-recessed bottom in the top
cabinet, the hole for the cord may need
to be enlarged.)
3. Tighten the two unit mounting screws
located in the grease filter openings.
See Figure 21.
4. Install grease filters by fitting into the
opening. Push back and up into place.
See Figure 22.
5. Use the two Top Cabinet Screws (D) and
two Flat Washers (E), supplied in the
INSTALLATION HARDWARE, to attach the
unit to the top cabinet. See Figure 23.
6. Make a bundle of the power supply cord
and place it inside the cabinet.
Figure 20
Unit mounting screw
Grease filter
Figure 21
Figure 22
Grommet (for metal
cabinet only)
(D)
(E)
Figure 23
7
MOUNTING DEFLECTOR
CHECKLIST FOR INSTALLATION
1. Make sure the unit has been installed according to all of the Installation Instructions
and the Wall and Top Cabinet Templates.
2. Plug in the power cord.
3. Keep the use and care guide.
Fisher & Paykel Appliances, Inc.
5900 Skylab Road, Huntington Beach, CA 92647
Customer Care: 888.936.7872
Fax: 714.372.7003
www.fisherpaykel.com
P/N 243710 D
TINSEB515MRR3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising