Liebherr | CS1410L | Installation instructions | Liebherr CS1410L Installation Instructions

Liebherr CS1410L Installation Instructions
Installation
Instructions
For NoFrost Combined
Refrigerator-Freezers
CS 1400 PC
CS 1400 R
CS 1410
7085 589-00
Important
Please Read and Follow these
Instructions
These instructions contain Danger, Warning and
Caution notes.
This information is important for safe and efficient installation and operation.
Always read and comply with all Danger, Warning and
Caution notes!
DANGER!
Danger indicates a hazard which
will cause serious injury or death if
precautions are not followed.
Content
Page
Please Read and Follow these Instructions.................. 2
Note to the Installer......................................................... 2
R600a Refrigerant.......................................................... 2
Disposal of Old Appliance.............................................. 3
Disposal of Carton.......................................................... 3
Electrical Safety.............................................................. 3
Blocking for Safety.......................................................... 3
Appliance Dimensions.................................................... 4
Cabinet Opening Dimensions........................................ 5
Unit Venting..................................................................... 6
Leveling the Appliance................................................... 6
Mounting the anti tipping device.................................... 7
Changing Over Door Hinges - CS 1400 R, CS 1410..... 8
Changing Over Door Hinges - CS 1400 PC.................14
WARNING!
Warning indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.
CAUTION!
Caution indicates a potentially hazardous
situation which, if not avoided, may result
in minor or moderate injury.
IMPORTANT
This indicates information that is especially
relevant to a problem-free installation and
operation.
Note to the Installer
It is very important to follow the instructions in the
manual to ensure proper installation and operation of
the unit.
Before installing the unit, be sure to thoroughly read
and understand all of the information in this manual.
WARNING!
Electrocution hazard.
Do not connect to the electrical outlet
before the installation is completed.
2
R600a Refrigerant
WARNING!
The refrigerant contained within the
appliance R600a is environmentally
friendly, but flammable. Leaking
refrigerant can ignite.
To prevent possible ignition follow
the warnings below:
• Keep ventilation openings, in
the appliance enclosure or in
the built-in structure, clear of
obstruction.
• Do not damage the refrigerant
circuit.
• Component parts and power cords
shall be replaced with like components
performed by factory authorized service
personnel only.
Safety
Disposal of Old Appliance
DANGER!
Risk of child entrapment.
Child entrapment and suffocation are not problems of
the past.
Junked or abandoned refrigerators are still dangerous –
even if they will sit for “just a few days.”
If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.
Electrical Safety
Connect this appliance to a 15 amp or 20 amp, 110120 VAC, circuit which is grounded and protected by a
circuit breaker or fuse.
We recommend using a dedicated circuit for this appliance to prevent circuit overload and the chance of interruption to the appliance.
This appliance is equipped with a three-prong (grounding) polarized plug for your protection against possible
shock hazards.
Before you discard old appliances:
• Take off the doors.
Where a two-prong wall receptacle is encountered,
contact a qualified electrician and have it replaced with
a properly grounded three-prong receptacle in accordance with all local codes and ordinances.
• Leave the shelves in place so that children may not easily climb inside.
Disconnect power before installing optional Side By
Side Kit.
• Cut off the power cable from the discarded refrigerator. Discard separately from
the refrigerator.
• Be sure to follow your local requirements
for disposal of appliances.
Contact the trash collection agency in
your area for additional information.
Disposal of Carton
The packaging is designed to protect the appliance and
individual components during moving and is made of
recyclable materials.
WARNING!
Keep packaging materials away from
children. Polythene sheets and bags can
cause suffocation!
Please recycle packaging material where facilities are
available.
WARNING!
Electrocution hazard.
Electrical grounding required.
• Do not remove the round grounding
prong from the plug.
• Do not use extension cords or
ungrounded (two prong) adapters.
• Do not use a power cord that is frayed or
damaged.
•
Do not use a power strip.
Failure to follow these
instructions may result in fire,
electrical shock or death.
Blocking for Safety
WARNING!
To avoid a hazard due to instability of the
appliance, it must be fixed in accordance
with the instructions.
3
Planning Information
Appliance Dimensions
Overall height of the appliance can be increased
by a maximum of 5/8” (see Leveling the appliance).
Model
A
B
C
CS 1400 PC 40 15/16" 66 5/16" 65 5/8"
CS 1400 R 1040 mm 1684 mm 1666 mm
47 7/8"
73 3/16" 72 1/2"
CS 1410
1216 mm 1859 mm 1841 mm
4
Planning Information
Cabinet Opening Dimensions
The appliance can be used freestanding or semi built-in.
If semi built-in, please consider the cabinet opening dimensions.
CS 1410
CS 1400 R, CS 1400 PC
This is where the power
cord extends from the back
of the appliance.
This is where the power
cord extends from the back
of the appliance.
Free length of the power
cord = 98 inch (2500 mm).
Free length of the power
cord = 98 inch (2500 mm).
IMPORTANT
The power plug must be easily accessible so that the appliance can be disconnected from the mains
quickly in an emergency. It must not be behind the back of the appliance.
NOTE
If the gap between the rear of the appliance and the wall is less than 2 inch (51 mm) , the power consumption
level may increase.
5
Installation
Unit Venting
Leveling the Appliance
Do not restrict the air flow.
The ventilation opening can either be directly over the
appliance
, above the cabinet and below the ceiling
or through a vent installed in a soffit
.
1
2
3
IMPORTANT
The clear ventilation cross-section must be at
least 31 in² (200 cm²) from the lower ventilation
opening right to the upper one.
The section below the freezer door and the floor
must not be covered.
The height can be
adjusted in front by twisting the leveling feet.
22 mm
wrench
Twist the adjusting bolt to set up
the back of the appliance. Align
the appliance with sides of kitchen
cabinets by adjusting leveling feet
and the supports.
5 mm socket
IMPORTANT
After final installation, this screw must be turned
down until it has proper floor contact to support
the hinge bracket.
6
Blocking For Safety
Mounting the anti tipping device
WARNING!
Tip over hazard!
The anti tipping brackets must be
mounted to prevent the appliance from
tipping when the fully stocked door is
opened.
IMPORTANT
Be sure that there is no plumbing or electrical
wiring located in this area which screws or drills
could damage.
1. Mark the center of the appliance on the back wall.
2. Mount the anti tipping brackets within the given area.
Center line of appliance.
IMPORTANT
The screws for fastening the anti-tip device are
not supplied with the appliance. Appropriate
screws must be used for the material (wood,
concrete, etc.) in which the safety device is
mounted.
7
Reversing Door Hinges
Changing Over Door Hinges - CS 1400 R, CS 1410
Door hinges should only be changed by a trained
expert.
Changing over the door hinges requires two people.
1. Open top door, pry off
door cover and pivot to
the left.
5.
4.
4. Pull the left-hand side of the cover
approx. 1/4" (6 mm) towards you.
1.
5. Remove pin.
2.
3.
2. Let door cover hang down.
3. Slide red safety bracket over
the hinge.
6.
6. Open top door wide and
remove covers.
7.
IMPORTANT
The two knobs on the safety bracket
must be fully inserted into the
marked openings on the hinge.
8
7. Remove cover.
Reversing Door Hinges
IMPORTANT
The door must now be held secure by another
person.
8.
12.
8. Remove cover from upper door
mounting and unscrew door.
12. Open bottom door, pry off
door cover.
14.
15.
10.
9.
13.
13. Pivot door cover to the left.
9.
Transfer fastener for soft stop
mechanism to the opposite side.
14. Slide red safety bracket over
the hinge.
15. Remove pin.
10. Transfer cover plate to the opposite side.
11.
16.
11. Remove cover.
16. Open bottom door wide and
remove cover.
9
Reversing Door Hinges
IMPORTANT
The door must now be held secure by another
person.
24.
17.
18.
17. Pull out middle hinge pin.
18. Remove bottom door.
25.
23.
23. Tilt appliance slightly backwards and unscrew the adjustable foot.
24. Remove the hinge pin.
25. Unscrew hinge bracket.
19.
20.
21.
19. Unscrew hinge bracket.
20. Transfer cover plate to the opposite side.
26. Transfer fastener
for soft stop mechanism on hinge
bracket to the opposite side.
26.
27. Transfer cover to the
opposite side.
27.
21. Turn hinge bracket through
180° and screw into place.
22.
22. Remove hinge bushing, turn
through 180° and re-fit.
10
28.
29.
28. Transfer cover plate to the
opposite side.
29. Screw hinge bracket into
place.
Reversing Door Hinges
30.
35.
Both doors
30. Tilt appliance slightly backwards,
insert pin and attach using the
adjustable foot.
31.
34. 36.
34. Remove screw.
35. Pivot soft stop mechanism outwards on
the right, pull to the right and remove.
36. Slide spacer to the left and remove.
37.
32.
38.
Both doors
31. Release pressure plates at
the front 1 and pull them
backwards to remove 2.
32.
37. Turn spacer through 180° and re-fit
on the opposite side.
38. Turn soft stop mechanism through
180° and re-fit on the opposite side.
Then secure both parts with screws.
32. Transfer door handle and
plugs to the opposite side.
33.
33. Transfer panels of both
door covers to the opposite side.
39.
33.
39. Suspend bottom door on
hinge pin.
IMPORTANT
The door must now be held secure by another
person.
11
Reversing Door Hinges
40.
45.
45. Click cover into place.
40. Insert middle hinge pin.
46.
46. Using a screwdriver, push out
the hinge from underneath and
remove it from the door .
41.
41. Slide door cover over soft stop
mechanism hinge.
42.
43.
47.
47. Using a screwdriver, push out
the plug from underneath and
transfer it to the opposite side.
44.
42. Move soft stop mechanism
hinge to the fastener and insert
pin.
48.
43. Remove red safety bracket.
44. Pivot door cover to the left and
click into place on the door.
48. Insert hinge.
12
Reversing Door Hinges
54.
49.
55.
53.
53. Pull the right-hand side of the cover
approx. 1/4" (6 mm) towards you.
49. Suspend top door on hinge pin.
For this, the door must be open
at least 90°.
54. Move soft stop mechanism hinge to
the fastener and insert pin.
55. Remove red safety bracket.
IMPORTANT
The door must now be held secure by another
person.
50.
56.
56. Pivot door cover to the left and click
into place on the door.
50. Secure door with screws
and click cover into place.
57.
52.
51.
51. Click cover into place.
52. Slide door cover over soft stop
mechanism hinge.
57. Click cover into place.
58. Place the appliance in its final
position at the place of installation.
Extend the adjustable foot at
the bottom hinge bracket until
it rests on the floor and then
make a further 90° turn.
58.
13
Reversing Door Hinges
Changing Over Door Hinges - CS 1400 PC
Door hinges should only be changed by a trained
expert.
5.
Changing over the door hinges requires two people.
6.
1.
7.
5.
Unscrew hinge bracket.
6.
Transfer cover plate to the opposite side.
7.
Turn hinge bracket through 180°
and screw into place.
IMPORTANT
The door must now be held secure
by another person.
1. Remove cover from upper door
mounting and unscrew door.
8.
2.
8.
Remove hinge bushing, turn
through 180° and re-fit.
9.
2.
Transfer cover plate to the opposite side.
IMPORTANT
The door must now be held secure by another
person.
10.
3.
4.
14
3.
Pull out middle hinge pin.
4.
Remove bottom door.
8.
Tilt appliance slightly backwards and
unscrew the adjustable foot.
9.
Remove the hinge pin.
10. Unscrew hinge bracket.
8.
Reversing Door Hinges
16.
11. Transfer the hinge component on the hinge bracket
to the opposite side.
17.
11.
Both doors
17.
16. Release pressure plates at
the front 1 and pull them
backwards to remove 2.
17. Transfer door handle and
plugs to the opposite side.
12. Transfer cover to the opposite side.
12.
Both doors
13.
18. Transfer spring clip to the opposite side.
14.
13. Transfer cover plate to the opposite side.
19.
14. Screw hinge bracket into place.
19. Suspend bottom door on
hinge pin.
IMPORTANT
The door must now be held secure by another
person.
20.
15.
15. Tilt appliance slightly backwards, insert
pin and attach using the adjustable foot.
20. Insert middle hinge pin.
15
Reversing Door Hinges
IMPORTANT
The door must now be held secure by another
person.
21.
24.
21. Using a screwdriver, push out
the hinge and remove it from
the door .
24. Suspend top door on hinge pin. For this,
the door must be open at least 90°.
22.
25.
22. Using a screwdriver, push out
the plug and transfer it to the
opposite side.
25. Secure door with screws
and click cover into place.
23.
23. Insert hinge.
26.
26. Place the appliance in its final position at the place of installation.
Extend the adjustable foot at the
bottom hinge bracket until it rests
on the floor and then make a further
90° turn.
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising