Dacor | EWD24SCH | Planning Guide [618 KB] | Dacor EWD24SCH Planning Guide [618 KB]

Dacor EWD24SCH Planning Guide [618 KB]
DWD, ERWD, EWD, IWD, MRWD,
MWDH, MWDV, OWD, RWDV
Document # PG02-002
24”, 27”, 30”, 36” Wide
Warming Drawers
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
DWD
ERWD
3 1/2”
(8.9 cm)
1”
(2.5 cm)
MRWD30B
(only)
1 7/16”
(3.7 cm)
EWD
3 7/16”
(8.7 cm)
1 1/8”
(2.9 cm)
All other MRWD
series
1”
(2.5 cm)
Revised 01/18/12 Page 1/3
PLANNING
GUIDE
Electrical Circuit Required
Total Connected Load
Minimum Ambient
Operating Temperature
120 Vac, 60 Hz, 15 Amp.
grounded, dedicated circuit
4.0 Amp. @
120 Vac, 60 Hz.
32°F (0°C)
1”
(2.5 cm)
10 1/8”
(25.7 cm)
MWDH, MWDV,
RWDV
3 1/4”
(8.3 cm)
A
1”
(2.5 cm)
Drawer Face Dimensions
(MWD Series Shown)
Handle Dimensions - side view
Mounting
hole 9 places
40” (101.6 cm)
3-prong 120 Vac
power cord
9"
(22.9 cm)
1/2" (1.3 cm)
B
C
Chassis
10"
(25.4 cm)
Chassis without
drawer inserted
1/2" (1.3 cm)
23 3/8”
(59.4 cm)
Chassis Dimensions
(A) Drawer Face
Width
(B) Chassis Face
Width
(C) Chassis
Width
DWD30
30” (76.2 cm)
29 5/8” (75.2 cm)
28 1/4” (71.8 cm)
ERWD27
27” (68.6 cm)
26 5/8” (67.6 cm)
25 1/4” (64.1 cm)
ERWD30
30” (76.2 cm)
29 5/8” (75.2 cm)
28 1/4” (71.8 cm)
EWD24
24” (61.0 cm)
23 5/8” (60.0 cm)
22 1/4” (56.5 cm)
EWD27
27” (68.6 cm)
26 5/8” (67.6 cm)
25 1/4” (64.1 cm)
EWD30
30” (76.2 cm)
29 5/8” (75.2 cm)
28 1/4” (71.8 cm)
EWD36
36” (91.4 cm)
35 5/8” (90.5 cm)
34 1/4” (87.0 cm)
MRWD27
26 3/4” (67.9 cm)
26 5/8” (67.6 cm)
25 1/4” (64.1 cm)
MRWD30
29 3/4” (75.6 cm)
29 5/8” (75.2 cm)
28 1/4” (71.8 cm)
MWDH27
27” (68.6 cm)
26 5/8” (67.6 cm)
25 1/4” (64.1 cm)
MWDH30
30” (76.2 cm)
29 5/8” (75.2 cm)
28 1/4” (71.8 cm)
MWDV27
27” (68.6 cm)
26 5/8” (67.6 cm)
25 1/4” (64.1 cm)
MWDV30
30” (76.2 cm)
29 5/8” (75.2 cm)
28 1/4” (71.8 cm)
RWDV30
30” (76.2 cm)
29 5/8” (75.2 cm)
28 1/4” (71.8 cm)
Model
5/64"
(2 mm)
Drawer open
23 13/16”
(60.5 cm)
Overall Dimensions - Top View
(EWD Series Shown)
Warming Drawer Overall Dimensions
All specifications subject to change without notice.
www.dacor.com
Phone: (800) 793-0093
Document # PG02-002
DWD, ERWD, EWD, IWD, MRWD,
MWDH, MWDV, OWD, RWDV
Revised 01/18/12 Page 2/3
24”, 27”, 30”, 36” Wide
Warming Drawers
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
C
B
Chassis
PLANNING
GUIDE
Electrical Circuit Required
Total Connected Load
Minimum Ambient
Operating Temperature
120 Vac, 60 Hz, 15 Amp.
grounded, dedicated circuit
4.0 Amp. @
120 Vac, 60 Hz.
32°F (0°C)
E
5/16”
(8 mm)
D
A
Drawer open
Drawer Face Dimensions
(IWD/OWD Series Shown)
F
40" (101.6 cm)
3 prong
120 Vac power cord
Mounting hole,
9 places
Overall Dimensions - IWD/OWD Series
Top View
**
**
**
**
G
Chassis without
drawer installed
** = OWD24 mounting holes
Chassis Dimensions
(IWD/OWD Shown)
Model
(A) Dimension
Drawer Face Width
(B) Dimension
Chassis Width
(C) Dimension
Chassis Face
Width
IWD24
22 5/16” (56.7 cm)
22 1/4” (56.5 cm)
22 3/8” (56.8 cm)
IWD27
25 5/16” (64.3 cm)
25 1/4” (64.1 cm)
25 3/8” (64.5 cm)
IWD30
28 5/16” (71.9 cm)
28 1/4” (71.8 cm)
28 3/8” (72.1 cm)
OWD24
22 1/2” (57.1 cm)
22 1/2” (57.1 cm)
22 1/2” (57.1 cm)
All specifications subject to change without notice.
(D)
Dimension
Drawer Face
Height
(E)
Dimension
Chassis
Depth
(F)
Dimension
Drawer
Depth
(G)
Dimension
Chassis
Height
8 15/16”
(22.7 cm)
23 3/8”
(59.4 cm)
23 13/16”
(60.5 cm)
9 1/16”
(23.0 cm)
11 7/8”
(30.2 cm)
20”
(50.8 cm)
18”
(45.7 cm)
11 7/8”
(30.2 cm)
www.dacor.com
Phone: (800) 793-0093
DWD, ERWD, EWD, IWD, MRWD,
MWDH, MWDV, OWD, RWDV
Document # PG02-002
24”, 27”, 30”, 36” Wide
Warming Drawers
Cabinet/countertop tolerances: +1/16” (+1.6 mm), -0 unless otherwise stated
Warming
drawer
36" typ.
(91.4 cm)
C
PLANNING
GUIDE
warning
•
Observe all governing codes and ordinances
during planning and installation. Contact your
local building department for further information.
•
This appliance must be installed in accordance
with the accompanying installation instructions.
3/4" min.*
(1.9 cm)
D
120 Vac
electrical
outlet
Warming
drawer
C
3/4" min.*
(1.9 cm)
Mounting platform must be 3/4" (1.9 cm) thick
and support 100 lbs.
A
B
1 1/2" (3.8 cm)
Typical countertop
Cooktop
27"/30"/36" Dacor
single wall oven
Warming
drawer
D
Warming
drawer
120 Vac
elect.
Warming
drawer
120 Vac
elect.
C
D
Toe kick
A
Model
DWD30
ERWD27
ERWD30
EWD24
EWD27
EWD30
EWD36****
IWD24
IWD27
IWD30
MRWD27
MRWD30
MWDH27
MWDH30
MWDV27
MWDV30
OWD24*****
RWDV30
Revised 01/18/12 Page 3/3
36" typ.
(91.4 cm)
C
A
B
C
3/4” min.*
(1.9 cm)
120 Vac
electrical
outlet
3/4" min.*
(1.9 cm)
(A) Cutout Width
28 1/2” (72.4 cm)
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
22 1/2” (57.2 cm)
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
34 1/2” (87.6 cm)
22 1/2” (57.2 cm)
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
22 5/8” (57.5 cm)
28 1/2” (72.4 cm)
(B) Min. Width to
Adjacent Doors/
Drawers
30 1/4” (76.8 cm)*
27 1/4” (69.2 cm)*
30 1/4” (76.8 cm)*
24 1/4” (61.6 cm)*
27 1/4” (69.2 cm)*
30 1/4” (76.8 cm)*
36 1/4” (92.1 cm)*
**
**
**
27” (68.6 cm)*
30” (76.2 cm)*
27 1/4” (69.2 cm)*
30 1/4” (76.8 cm)*
27 1/4” (69.2 cm)*
30 1/4” (76.8 cm)*
24 1/4” (61.6 cm)***
30 1/4” (76.8 cm)*
(C) Cutout Height
(D) Min. Vertical Gap
Between Cutouts
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
11 15/16” (30.3 cm)
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
NA
1 1/16” (2.7 cm)
1 1/16” (2.7 cm)
1 1/16” (2.7 cm)
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
NA
1 1/4” (3.2 cm)*
Min. Cutout Depth
24” (61.0 cm)
20 1/8” (51.1 cm)
24” (61.0 cm)
* Bare minimum spacing to allow for ventilation and avoid scraping on DWD, ERWD, EWD, MRWD, MWDH, MWDV and RWDV series models.
** On IWD series models or OWD24 without the optional front panel kit: The chassis and the drawer faceplate are smaller than the cutout.
The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must exceed the appropriate cutout
dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space on the top, bottom and sides from the
custom front panel edge to prevent scraping against adjacent doors, drawers and the countertop.
*** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and below
cutout is 3/4” minimum. See ** above for OWD24 with custom front panel.
**** Model EWD36 cannot be installed above or below another warming drawer (any type).
***** Model OWD24 cannot be installed above, below or adjacent to a wall oven or warming drawer (any type).
All specifications subject to change without notice.
www.dacor.com
Phone: (800) 793-0093
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising