Maytag | MGS8800FZ | MGS8800FZ Dimension Guide EN | Maytag MGS8800FZ MGS8800FZ Dimension Guide EN

30" (76.2 cm) Freestanding Gas Range
PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
MGS8880D
This manual covers several models. Your model may appear different
from the models depicted. Dimensions given are maximum dimensions
across all models.
MGS8800F
GAS SUPPLY REQUIREMENTS
Gas supply line:
■■ Provide a gas supply line of 3/4" (1.9 cm) rigid pipe to the range
location. A smaller size pipe on longer runs may result in insufficient
gas supply. With LP gas, piping or tubing size can be 1/2" (1.3 cm)
minimum. Usually, LP gas suppliers determine the size and materials
used in the system.
NOTE: Pipe-joint compounds that resist the action of LP gas must be
used. Do not use TEFLON®† tape.
B
A
C
Flexible metal appliance connector:
■■ If local codes permit, a new CSA design-certified, 4 to 5 ft (122
to 152.4 cm) long, 1/2" (1.3 cm) or 3/4" (1.9 cm) I.D., flexible metal
appliance connector may be used for connecting range to the gas
supply line.
D
■■ A 1/2" (1.3 cm) male pipe thread is needed for connection to the
female pipe threads of the inlet to the appliance pressure regulator.
E
■■ Do not kink or damage the flexible metal tubing when moving the
F
range.
■■ Must include a shutoff valve:
The supply line must be equipped with a manual shutoff valve. This
valve should be located in the same room but external to the range
opening, such as an adjacent cabinet. It should be in a location that
allows ease of opening and closing. Do not block access to shutoff
valve. The valve is for turning on or shutting off gas to the range.
B
A. 13/16" (3.0 cm) height from
cooktop to top of vent
B. 297/8" (75.9 cm)
C. Model/serial number plate
(located behind the oven door
on the top right-hand side of
the oven frame)
D. 36" (91.4 cm) height to top of
cooktop edge with leveling legs
screwed all the way in*
E. 285/16" (71.9 cm) max. depth
from front of console to back of
range.
F. 287/8" (73.3 cm) max. depth
from handle to back of range.
IMPORTANT: Range must be level after installation. Follow the
instructions in the “Level Range” section. Using the cooktop as a
reference for leveling the range is not recommended.
A
* Range can be raised approximately 1" (2.5 cm) by adjusting the
leveling legs.
C
A. Gas supply line
B. Shutoff valve “open” position
C. To range
Type of Gas
Gas Pressure Regulator
Natural gas:
The gas pressure regulator supplied with this range must be used. The
inlet pressure to the regulator should be as follows for proper operation:
■■ This range is factory set for use with Natural gas. See “Gas
Natural gas:
Minimum pressure: 5" WCP
Maximum pressure: 14" WCP
Conversions” section. The model/serial rating plate located behind the
control panel has information on the types of gas that can be used. If
the types of gas listed do not include the type of gas available, check
with the local gas supplier.
LP gas conversion:
LP gas:
Conversion must be done by a qualified service technician.
Minimum pressure: 11" WCP
Maximum pressure: 14" WCP
Contact local gas supplier if you are not sure about the inlet pressure.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different gas
without consulting the serving gas supplier. See “Gas Conversions”
section.
†®TEFLON is a registered trademark of Chemours.
Because Whirlpool Corporation includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10665256E
05/23/2016
ELECTRICAL REQUIREMENTS
IMPORTANT: The range must be electrically grounded in accordance
with local codes and ordinances, or in the absence of local codes, with
the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code,
CSA C22.1.
If codes permit and a separate ground wire is used, it is recommended
that a qualified electrical installer determine that the ground path is
adequate.
■■ A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is
required. A time-delay fuse or circuit breaker is also recommended.
It is recommended that a separate circuit serving only this range be
provided.
■■ Electronic ignition systems operate within wide voltage limits, but
proper grounding and polarity are necessary. Check that the outlet
provides 120-volt power and is correctly grounded.
CABINET OPENING DIMENSIONS
Cabinet opening dimensions shown are for 25" (64.0 cm) countertop
depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop
height.
IMPORTANT: If installing a range hood or microwave hood combination
above the range, follow the range hood or microwave hood combination
installation instructions for dimensional clearances above the cooktop
surface.
D
B
C
Range may be installed next to combustible walls with zero clearance.
NOTE: When installed in a slide-in cutout, the front of oven door may
protrude beyond the base cabinet.
A.
B.
C.
D.
E.
18" (45.7 cm) upper side cabinet to countertop
13" (33 cm) max. upper cabinet depth
30" (76.2 cm) min. opening width
For minimum clearance to top of cooktop, see NOTE*.
In U.S.A.: 30" (76.2 cm) min. opening width
In Canada: 31" (78.7 cm) min. opening width
F. 3" (7.6 cm) min. clearance from both sides of range to side wall or
other combustible material.
G. The shaded area is recommended for installation of rigid gas pipe and
grounded outlet.
H. 131/8" (33.3 cm)
I. 711/16" (19.5 cm)
J. 413/16" (12.2 cm)
K. 311/16" (9.4 cm) or measurement of N, whichever is greater
L. 12" (30.5 cm)
M. Cabinet door or hinges should not extend into the cutout.
N. Remaining counter depth should not exceed 21/4" (5.7 cm)
L
A
E
K
G
H
F
I
J
I
* NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet
is shielded by not less than 1⁄4" (0.64 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm)
stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an uncovered wood or metal cabinet.
Page 2 of 2
Because Whirlpool Corporation includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10665256E
05/23/2016
Download PDF

advertising