Superiore | RN362GCSS | Installation instructions | Superiore RN362GCSS Installation Instructions

Superiore RN362GCSS Installation Instructions
461308462 07-2015
INSTALLATION MANUAL FOR
30’’ AND 36’’ GAS RANGES
Table of Contents
Warnings & Important Safety Instructions
Dimensions
Specifications Technical data
Clearance Dimensions (Proximity to Cabinets)
Clearance Dimensions (Wood/Composite Overlay)
Electrical & Gas Requirements
General Information
Installation/ Door Removal
Leg Installation/Adjustments/Alignments
Anit-tip Device Installation
Connecting Gas & Electrical
Final Preparation
Performance Checklist
Service & Registration
Warranty USA
3
6
10
11
12
13
15
16
17
18
19
20
20
22
23
WARNING: If the information in this manual is not followed exactly, a
fire or explosion may result causing property damage, personal injury or
death.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity
of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
– Do not try to light any appliance.
– Do not touch any electrical switch;
– Do not use any phone in your building.
– Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
– If you cannot reach your gas supplier, call the fire department.
• Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
2
Warnings & Important Safety Instructions
• Before beginning, please read these
instructions completely and carefully.
• DO NOT remove permanently affixed
labels, warnings, or plates from product.
This may void the warranty.
• All local and national codes and ordinances must be observed.
Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSIZ223.1 INFPA54.
• The installer must leave these instructions with the consumer who should
retain for local inspector’s use and for
future reference.
In Canada: Installation must be in
accordance with the current CAN/CGA
B149.1 & 2 Gas Installation codes and/
or local codes. Electrical installation must
be in accordance with the current CSA
C22.1 Canadian Electrical Codes Part 1
and/or local codes.
Your safety and the safety of others
is very important.
We have provided many important safety
messages in this manual and on your
appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to hazards
that can kill or hurt you and
others.
All safety messages will be preceded by
the safety alert symbol and the
word“DANGER,” “WARNING” or
“CAUTION.”
These words mean:
DANGER
Hazards or unsafe practices which WILL result in severe personal
In Massachusetts: All gas products must injury or death.
be installed by a “Massachusetts” licensed
plumber or gasfitter. A “T” type handle
manual valve must be installed in the gas
supply line to the appliance.
Hazards or unsafe practices which
COULD result in severe personal
In California:
injury or death.
WARNING: This product contains
chemicals known to the State of
California to cause cancer and birth
defects or other reproductive harm.
(California law requires this warning to
Hazards or unsafe practices which
be given to customers in the State of
COULD result in minor personal
California).
injury or property damage.
WARNING
An air curtain or other overhead range hood which operates by blowing a
downward airflow onto the range, shall
not be used with a gas range.
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
3
461308462 07-2015
CAUTION
Warnings & Important Safety Instructions
A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local ordinances.
•The required use of a GFI is normally related to the location of a receptacle with
respect to any significant sources of water or moisture.
•TECNOGAS SUPERIORE will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
If the use of a GFI is required, it should be:
• Of the receptacle type (breaker type or portable type NOT recommended)
• Used with permanent wiring only (temporary or portable wiring NOT recommended)
• On a dedicated circuit (no other receptacles, switches or loads in the circuit)
• Connected to a standard breaker of appropriate size (GFI breaker of the same size
NOT recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor
situations)
•Protected from moisture (water, steam, high humidity) as much as reasonably possible
WARNING
To prevent possible damage to cabinets and cabinet finishes, use only materials and
finishes that will not discolor or delaminate and will withstand temperatures up to
194°F (90°C). Heat resistant adhesive must be used if the product is to be installed in
laminated cabinetry. Check with your builder or cabinet supplier to make sure that
the materials meet these requirements.
4
Warnings & Important Safety Instructions
CHEMICAL HAZARD
To avoid risk of property
damage and/or personal
injuryor death; this
appliance is not too be
used as a heating source.
• Benzene is a chemical which is part of
the gas supply to this cooking
product, which is consumed in the
flames during combustion. Exposure to a
small amount of benzene is
possible if a gasleak occurs.
Formaldehyde and soot are by
products of incomplete combustion.
• This appliance contains or produces
chemicals which can cause serious injury
or death and which are known to the
state of California to cause cancer, birth
defects or other reproductive harm.
To reduce the risk from substances in
the fuel or from fuel combustion make
sure this appliance is installed, operated,
and maintained in accordance to the
instructions in this document.
DANGER
ELECTRICAL SHOCK
HAZARD
To avoid risk of electrical
shock, personal injury or
death; verify your
appliance has been
properly grounded in accordance with
local codes or in absence of
codes, with the National Electrical Code
(NEC). ANSI/NFPA 70-latest edition.
WARNING
MOVING HAZARD
To avoid risk of severe
personal injury; this
appliance requires two
or more personnel
while handling and moving. Possible use of
appliance moving devices is recommended.
WARNING
TIPPING HAZARD
To reduce the risk of
property damage or
personal injury; install
anti-tipping device
provided in accordance
with the installation
instructions in this
document. Device must be
engaged properly to prevent
product from tipping over.
• This range can tip
• Injuries to persons can result
• Install anti-tip device packed with
range
• See installation instructions
DANGER
GAS LEAK HAZARD
To avoid risk of
personal injury or death; leak
testing of the
appliance must be conducted
according to the manufacturer’s
instructions. Before placing appliance in
operation, always check for gas leaks with
soapy water solution.
• DO NOT USE AN OPEN FLAME
TO CHECK FOR GAS LEAKS.
5
461308462 07-2015
DANGER
Dimensions
35"
7/8 min
- 37"
5/16 max
2"
1" 3/8
30” Gas Ranges
23
29
"
8
"7 /
2" 3
/
16
Note: Unit shown with island trim.
Note: All gas ranges are equipped with spacer on the back (25/64) to prevent over
heating of the wall.
6
2" 3/16
23"
26" 7/8
2" 3/8
1" 11/32
1" 11/32
1" 3/8
2" 1/8
2"
5"
Electricity
2" 27/64
461308462 07-2015
2" 6/8
3/8"
25"
33"
2"
1" 3/8
29" 7/8
2" 6/8 min
4" 1/4 max
35" 15/32 min - 36" 7/8 max
2" 1/8
5"
35" 7/8 min - 37" 5/16 max
Dimensions
30” Gas Ranges
1" 3/8
29" 7/8
Gas
5" 9/16
2"
3/8"
1" 1/2
7
Dimensions
35" 7/8 min - 37" 5/16 max
2"
1" 3/8
33"
36”Gas Ranges
23
"
35
"
7 /8
2" 3
/
16
Note: Unit shown with island trim.
Note: All gas ranges are equipped with spacer on the back (25/64) to prevent over
heating of the wall.
8
2" 3/16
23"
26" 7/8
2" 3/8
1" 11/32
1" 11/32
1" 3/8
2" 1/8
2"
5"
Electricity
2" 27/64
461308462 07-2015
2" 6/8
3/8"
2"
25"
33"
2"
1" 3/8
35" 7/8
2" 6/8 min
4" 1/4 max
35" 15/32 min - 36" 7/8 max
2" 1/8
5"
35" 7/8 min - 37" 5/16 max
Dimensions
36”Gas Ranges
1" 3/8
35" 7/8
Gas
5" 9/16
2"
3/8"
1" 1/2
9
Specifications Technical data
Burners - injectors and volume, range 30‘‘ (mod. ...301...)
Natural 4’’
LP/Propane 11’’
By-pass
Inj.
W
BTU/h
Inj.
W
BTU/h
Ø
W
BTU/h
Small burner
92
1055
3600
56
1055
3600
28
322
1100
Medium burners
117
1300
6500
70
1300
6500
34
381
1300
Large burner
155
2750
11000
93
2750
11000
44
791
2700
Power burner
Ext.
ring
Int. ring
137 (2)
80
4750
18000
82 (2)
50
4750
18000
65
1377
4700
Power burner
with simmer
Ext.
ring
Int. ring
137 (2)
80
750
18000
82 (2)
50
750
18000
60
27
1377
4700
Total gas power
77600
Oven
180
4103
14000
Grill
135
2345
8000
Feeding
108
4103
82
52
879
8000
-
-
2345
120 V
AHAM standard volume
14000
60 Hz
3000
-
130 W
4.1 Cubic Feet
Interior dimensions
24
13/64
x 1957/64 x 2031/64
Burners - injectors and volume, ranges 36‘‘(mod. ...361... and ...362...)
Natural 4’’
LP/Propane 11’’
By-pass
Inj.
W
BTU/h
Inj.
W
BTU/h
Ø
W
BTU/h
Small burner (*)
92
1055
3600
56
1055
3600
28
322
1100
Medium burner (**)
117
1661
5700
70
1661
5700
34
381
1300
Large burner
155
2931
10000
93
2931
10000
44
791
2700
Power burner
Ext.
ring
Int. ring
137 (2)
80
5275
18000
82 (2)
50
5275
18000
65
1377
4700
Power burner
with simmer
Ext.
ring
Int. ring
137 (2)
80
5275
18000
82 (2)
50
5275
18000
60
27
1377
4700
Total gas power
67700 (mod. ...362) and 77000 (mod. ...361...)
-
Oven
200
4689
16000
115
4689
16000
65
1290
Grill
155
2931
10000
92
2931
10000
-
-
120 V
60 Hz
Electric griddle
Feeding
1150 W 120 V
AHAM standard volume
Interior dimensions
(*) Only on mod. ...361
(**) 2 burners on mod. ...361... ; 1 burner on mod. ...362...
10
170 W (mod...361...) or 1320 W (mod....362...)
4.8 Cubic Feet
283/4 x 1957/64 x 2031/64
4400
-
Clearance Dimensions (Proximity to Cabinets)
•This range may be installed
directly adjacent to existing 36”
(91.4 cm) high base cabinets.
IMPORTANT: The side trim
MUST be 3/8” (0.95 cm)
above the adjacent base
cabinet countertop. This can be
accomplished by raising the unit
adjusting the legs.
• The range CANNOT be
installed directly adjacent to
sidewalls, tall cabinets, tall
appliances, or other side
vertical surfaces above 36”(91.4
cm) high. There must be
a minimum of 6” (15.2 cm) side
clearance from the range to such
combustible surfaces above the
36” (91.4 cm) counter height.
• Wall cabinets above the range
must be a minimum of 42” (106.7
cm) above the range
cooking surface for the full
width of the range. This minimum
height requirement does not apply
if a range hood is installed over
the cooking surface.
Note: If a range hood is installed, wall cabinets
above the range have a different minimum clearance
height.
CAUTION
Burn hazard
To avoid risk of personal injury; the use of cabinets for storage above the
appliance may resultin a potential burn hazard.
Combustible items may ignite, metallic items may become hot and cause
burns. If a cabinet storage is to be provided the risk can be reduced by installing a range
hood that projects horizontally a minimum 5” (12.7 cm) beyond the bottom of cabinets.
11
461308462 07-2015
• Within the 6” (15.2 cm) side
clearance to combustible
vertical surfaces above 36” (91.4
cm), the maximum wall cabinet
depth must be 13” (33.0 cm) and
wall cabinets within this 6” (15.2
cm) side clearance must be 18”
(45.7 cm) above the 36” (91.4 cm)
high countertop.
Clearance Dimensions (Wood/Composite Overlay)
The bottom of a standard hood should be 30” (76.2 cm) min. to 36” (91.4 cm) max.
above the countertop. This would typically result in the bottom of the hood being 66”
(167.6 cm) to 72” (182.9 cm) above the floor. Refer to the range hood installation
instructions for additional information.
These dimensions provide for safe and efficient operation of the hood.
Important: There must be a minimum of 6” (15.2 cm) clearance from rear of range
to a combustible wall. Clearances from non-combustible materials are not part of
the ANSI Z21. 1 scope and are not certified by CSA. Clearances to non-combustible
materials must be approved by the authority having jurisdiction.
12
Electrical & Gas Requirements
Electrical Requirements
Check your national and local codes
regarding this unit. This range requires120VAC/60 Hz; 4 ft. (121.9 cm), 3-wire
cord with grounded 3-prong plug attached to unit. See “Electrical Connection”
section for grounding instructions. Must
be fused seperately from any other
circuit.
WARNING
ELECTRICAL SHOCK
HAZARD
To avoid the risk of electrical shock, personal injury or
death; verify
electrical power is turned off at the
breaker box and gas supply is turned off
until the range is installed and ready to
operate, installation by an authorized
installer only.
location where it can be reached quickly
in the event of an emergency. Any opeing
behind the range shall be sealed.
In Massachusetts: A “T” handle
type manual valve must be installed in the
gas supply line to the appliance.
IMPORTANT: Any conversion
required must be performed by
your dealer or a qualified licensed
plumber or gas service company.
Please provide the service person with
this manual before work begins.
Pressure Regulator
•All ranges have a pressure regulator on
the incoming service line for safe and
efficient operation, since service pressure
may fluctuate with local demand.
External regulators are not required on
this range since a regulator is supplied
with each unit. Under no condition bypass this regulator.
•Manifold pressure should be checked
with a manometer, natural gas requires
4.0”W.C.P. and LP gas requires 11.0”
The appliance must be disconnected from W.C.P. Incoming line pressure upstream
the gas supply piping system during any
from the regulator must be 1” W.C.P.
pressure testing of that system.
higher than the
manifold pressure in order to check the
The gas supply (service) line must be the regulator. The regulator used on this
same size or greater than the inlet line of range can withstand a
the appliance. This range uses a 1/2” (1.3 maximum input pressure of 1/2” PSI
cm) IDNPT (Sch40) inlet. Sealant on all
(14.0” W.C.P.). If the line pressure is in
pipe joints must be resistive to LP gas.
excess of that amount, a step down regulator will be required.
The range is designed specifically for
natural gas or liquid propane (LP)
gas. Before beginning installation
verify that the model is compatible
with the intended gas supply.
Manual shut-off valve:
This installer-supplied valve must be
installed in the gas service line before
the appliance in the gas stream and in a
13
461308462 07-2015
Gas Connection
Gas Requirements
TO INSTALL PRESSURE REGULATOR
1: Remove the 2 covers on the back of the 3 - Screw the assembled pressure regurange unscrewing the 3 screws indicated lator on the range like shown on picture
below. Pay attention to the vertical aligneon below pictures.
ment of the same pressure regulator.
COVERS
SCREWS
2 - Take from the top of packaging the
parts shown in the picture below to
assemble the pressure regulator.
14
4 - Re-install the covers previously
removed. On the cover on the pressure
regulator add the provided screw on the
left side like shown in the picture below.
Gas Requirements
Flexible Connections:
If the unit is to be installed with flexible
couplings and/or quick-disconnect fittings,
the installer must use a heavy-duty AGA
design-certified flexible connector or at
least1/2” (1.3 cm) ID NPT (with suitable
strainreliefs) in compliance with ANSI
Z21.41and Z21.69.
In Canada: CAN 1-6, 10-88 metal
connectors for gas appliances and CAN
1-6.9 M79 quick disconnect devices for
use with gas fuel.
In Massachusetts:This appliance must
be installed with a 36” (3-foot) long flexible gas connector.
461308462 07-2015
G - area for gas connection
E - area for electric connection
15
Gas Requirements
GAS CONVERSION
WARNING!
Before carrying out this operation,
disconnect the appliance from gas and
electricity. Gas conversion shall be
conducted by a factory-trained
professional. Call the customer service
hotline to identify a factory-trained
professional near your home. The gas
conversion procedure for this range
includes 6 steps:
1. Pressure regulator
2. Surface burners
3. Main oven burner
4. Broiler burner
5.Visual checks prior to closure of oven
bottom panel
6. Adjustment of minimum setting.
The conversion is not completed if all
6 steps have not been concluded
properly. Before performing the gas
conversion, locate the package
containing the replacement nozzle
shipped with every range.
IMPORTANT:
Each nozzle has a number indicating its
flow diameter printed on the body.
Consult the table on “Specifications
Technical data “paragraph for matching
nozzles to burners.
Save the nozzles removed from the
range for future use
16
STEP1:PRESSURE REGULATOR
The pressure regulator supplied with the
appliance is a convertible type pressure
regulator for use with Natural Gas at a
nominal outlet pressure of 4” w.c. or LP
gas at a nominal outlet pressure of 11”
w.c. and it is pre arranged from the factory to operate with one of these gas/
pressure as indicated in the labels affixed on the appliance, package and Instruction booklet.
To convert the regulator for use with
other liquid propane LP gas:
1. Unscrew by hand the upper cap of the
regulator, remove the white plastic
attachment from the cap, reverse its
direction and screw it again firmly against
the cap. The white plastic attachment must be turned as follow for
NATURAL GAS
and as reversed for LP/PROPANE GAS
2. Screw by hand the metal cap in the
original position on the regulator.
Gas Requirements
STEP 3: MAIN OVEN BURNER
To replace the nozzles of the main oven
burner, start by removing the bottom
panel of the oven.
Loose the 2 screw located on the left and
right sides of the burner and the burner
from its support.
ATTENTION: pay extra attention to avoid
damage to the igniter and thermocouple.
Unscrew the nozzle located inside the gas
fitting using a 10 mm or 7 mm socket
wrench. (It depends on type of injector)
461308462 07-2015
STEP 2: SURFACE BURNERS
To replace the nozzles of the surface
burners, lift up the burners and unscrew
the nozzles shipped with the range using
a 7 mm (sochet wrench). Replace nozzles using the conversion set
supplied with the range or by a Tecno
authorized parts warehouse. Each nozzle
has a number indicating its flow diameter
printed on the body. Consult the table
on “Specifications Technical data “
paragraph for matching nozzles to
burners.
For range 36”
17
Gas Requirements
Replace the nozzle using the conversion set
supplied with the range or by a Tecno
authorized parts warehouse. Each nozzle
has a number indicating its flow diameter
printed on the body. Consult the table on
“Specifications Technical data “ paragraph
for matching nozzles to burners.
Air adjustment is not needed.
STEP 4: BROILER BURNER
Loosen the 2 screws on left and right
sides and pull out the burner from its
support burner from its support. ATTENTION: pay extra attention
to avoid damage to the igniter and
thermocouple.
For range 30”
Using a 7 mm or 10 mm sochet wrench
to unscrew the nozzle. Replace the nozzle using the conversion set supplied with the range or by a Tecno authorized parts warehouse. Each nozzle has a
number indicating its flow diameter printed on the body. Consult the table on
“Specifications Technical data “ paragraph for matching nozzles to burners.
Air adjustment is not needed.
18
Gas Requirements
STEP 5:VISUAL CHECKS
Before reinstalling the bottom panel, the
following visual check must be performed
to ensure that the conversion has been
carried out properly and without damage
to other components of the range.
OVEN IGNITER AND
THERMOCOUPLE POSITION
The appropriate gap between the tip of
the spark plug or thermocouple and the
burner shall be approximately 1/8’’.
STEP 6: MINIMUM
FLAME ADJUSTMENT WARNING! These adjustments should
be made only for use of the appliance
with natural gas. For use with liquid
propane gas, the By-pass screw must be
fully turned in a clockwise direction. SURFACE BURNERS
1. Light one burner at a time and set the
knob to the MINIMUM position
(small flame).
2. Remove the knob.
3. The range is equipped with a safety
valve. Using a small size slotted
screwdriver, locate the By-pass screw
valve on the valve body and turn it to
the right or left until the burner flame
is adjusted to desired minimum.
4. Make sure that the flame does not go
out when switching quickly from the
MAXIMUM to the MINIMUM position.
The tip of the spark plug or
thermocouple must fully overlap at
least the first gas emission hole of the
burner. After performing all these
visual checks, reinstall the bottom
panel of the oven compartment and
proceed to setting the minimum for
each burner.
For simmer burners, on the tap in the right
19
461308462 07-2015
For all hob burners
Gas Requirements
OVEN BURNER
1. Set the oven temperature control
knob to the MAXIMUM setting.
2. Close the oven door and operate the
oven for at least 10 minutes.
3. Set the knob to the MINIMUM setting
4. Remove the knob.
5. With a slotted screwdriver turn the
choking screw (bypass screw at the left
side of the thermostat bar) and, while
observing the flame at the same time
through the bottom oven porthole,
evaluate the consistency of the flame so it
remains on when switching quickly from
MINIMUM to MAXIMUM setting.
20
General Information
• All openings in the wall behind the
appliance and in the floor under the
appliance must be sealed.
• Do not obstruct the flow of
combustion and ventilation air.
CAUTION
Avoid any damage to oven vents.
The vents need to be un obstructed and
open to provide proper airflow for optimal oven performance.
CAUTION
The cooling fans should be operating
when the unit is in operation. If you notice the cooling fans are not operating or
you observe unusual or excessive noise
coming from the cooling fans, contact a
TECNOGAS SUPERIORE Service Center
before continuing operation. Failure to do
so can result in damage to the oven or
surrounding cabinets.
Moving, Handling and Unpacking
Remove and discard all packing
materials, including cardboard and tape
on the outside and inside of the range.
Remove the burner grates and
styrofoam off the top cooking surface. Be
sure to remove the burner caps packaged
in styrofoam below the burner grates.
Do not discard the anti-tip
metal bracket supplied with the
range.This is the anti-tip device and must
be installed with the unit. Refer to“Anti-tip Device Installation”
section.
Some stainless steel parts may have a
plastic protective wrap which must be
peeled off. The interior should be washed
thoroughly with hot, soapy water to
remove film residues and any dust or
debris before being used, then rinsed and
wiped dry.
Solutions stronger than soap and water
are rarely needed.
461308462 07-2015
READ AND FOLLOW ALL
WARNING AND CAUTION
INFORMATION WHEN INSTALLING THIS APPLIANCE.
21
Installation/Door removal
NOTICE
DO NOT use the handle or oven door to lift the oven. DO NOT lift or carry the
door by the handle.
Removing the door must be done by your dealer, a qualified licensed
plumber, or certified gas installer
Door Removal
1)- Open the door completely. Place the
pins, supplied with unit, in pin hole. For
personal safety, ONLY use pins supplied
with the unit.
2)- Grasp the door as indicated in the
photos below and turn up until you perceive the block.
22
3)- Lift the door up and extract.
Leg Installation/Adjustments/Alignment
Tecnogas ranges must be used only with
the legs properly installed.
Adjust leg height to the desired level by
twisting the inside portion of the leg assembly until the proper height is reached.
Check with a level that the worktop
allignement is perfectly level.
Four height adjustable legs, assembled under the bottom of the range
insert the legs in the appropriate
receptacles
Remember that is indicated to set the
high corner of range so that the top of
side trim is 3/8” (0.95 cm) above countertop. (see paragraph “Dimension”)
Four height adjustable legs are delivered
with the range in the polysterene container situated over the appliance.
Before installing the legs, position the
appliance near its final location as the legs
are not suitable for moving the appliance
over long distances.
461308462 07-2015
After unpacking the range, raise it enough
to insert the legs in the appropriate
receptacles situated on the lower part
of the appliance. Lower the range gently
to keep any undue strain from legs and
mounting hardware. If possible use a pallet or lift jack instead of tilting the unit.
23
Anti-tip Device Installation
WARNING
TIPPING HAZARD:
To reduce the risk of property damage or personal injury;
install anti-tipping device provided in accordance with the
installation instructions in this
document.
Device must be engaged properly to prevent product from
tipping over.
TIPPING
Kit enclosed with the range.
Mark and drill holes where the bracket
will be located.
24
Measure from floor to the anti-tip bar
located in a slit on the back of the range.
Connecting Gas & Electric
DANGER
GAS LEAK HAZARD
To avoid risk of personal injury or death; leak testing of the
appliance must be conducted according to the manufacturer’s
instructions. Before placing appliance in operation, always
check for gas leaks with soapy water solution.
• DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS.
Before placing appliance in operation,
always check for gas leaks.
This must be performed by your dealer, a
qualified licensed plumber, or gas
service company.
Burner caps are packed in styrofoam
top pack with the grates. Place burner
on top of range. Place burner grate on
top of burner cap and grate support.
461308462 07-2015
Connect gas and electrical.
25
Final Preparation
•All stainless steel body parts should be
wiped with hot, soapy water and with a
liquid cleaner designed for this material.
If buildup occurs, DO NOT use steel
wool, abrasive cloths, cleansers, or powders! If it is necessary to scrape stainless
steel to remove encrusted materials,
soak
with hot, wet cloths to loosen the material, then use a wool or nylon scraper.
DO NOT use a metal knife, spatula, or
any other material tool to scrape stainless
steel! Scratches
arealmost impossible to remove.
Performance Checklist
A qualified installer should carry out the following checks:
•
Check top burner ignition.
Push and turn the knob “Full on“ position.
The low flame should light at every port.
•
•
Check oven bake function bake burner on full power.
Check convection broil function broil burner at full power with convection fan
on.
Check convection fan function convection fan comes on when switch is turned
on.
•
Worktop burner knob
OFF = Closed position
= “Full on” position (High flame)
= “Reduced rate” position (Low flame)
Rotary swicht knob
OFF = Closed position
= Oven light on
= Oven light on + fan
= Fan
26
Performance Checklist
Worktop burner knob + simmer
OFF
= Closed position
= “Full on” position
internal ring
= “Full on” position
esternal ring
Gas oven switch knob range 30’’
OFF
= Closed position
from MIN
to MAX = Oven temperatures
(300-450 °F)
Broil
= Broil
Gas oven switch knob range 36’’
OFF
from MIN
to MAX
(300-500 °F)
Broil
= Closed position
= Oven temperatures
= Broil
Electric griddle knob range 36’’
from 1 to 7
positions
= Closed position
= Griddle temperatures
461308462 07-2015
OFF
27
Service & Registration
Only authorized replacement parts may be used in performing service on the
appliance. All servicing should be referred to a qualified technician.
Contact TECNOGAS SUPERIORE 1-844-322-2111, for the nearest service parts
distributor in your area or write to: CUSTOMERCARE@TECNOSPA.IT
Record the information indicated below.
You will need it if service is ever required.
The model and serial number can be found by looking in the last page of this
booklet. A duplicate label is located on the back side of the range.
model number ...............................................................................
serial number .................................................................................
date of purchase ...........................................................................
date installed .................................................................................
dealer’s name ................................................................................
address ..........................................................................................
These installation instructions should remain with the unit for
future reference.
28
WARRANTY U.S.A
Please record your model (MOD) and serial number (S/N) below for
future reference. For your convenience, a label containing this information is
supplied with this booklet. When writing or calling about a service problem,
please include the following information:
- your name, address and telephone number
- appliance model and serial number
- name and address of your dealer
- a clear description of the problem you are having
- proof of purchase (sales receipt)
MOD:_______________________
S/N:________________________
EXCLUSIONS
This warranty does not cover any defect or damage, which is not direct fault
of TECNOGAS SUPERIORE; this includes, but is not limited to:
1) Service trips to your home to instruct you how to use the product.
2) Service trips to your home, during which no fault is found.
3) Damages occurred during transit, handling and/or installation of the product.
4) Damages occurred in case the product has not been installed, duly following
the manufacturer’s installation instructions, as well as any local code or regulation.
5) Damages due to failure in following the manufacturer’s recommended care,
cleaning and maintenance instructions; in particular, damages to the oven and/
or the worktop if they have not been cared and cleaned according to these
instructions.
29
461308462 07-2015
TECNOGAS SUPERIORE WARRANTY
TWO YEARS PARTS AND LABOR
For two year from the date of the original purchase, TECNOGAS SUPERIORE will
repair or replace (at its option) any part of the range which fails due to a defect
in materials or workmanship. During this warranty, TECNOGAS SUPERIORE will provide, free of charge, all labor and in-home service to repair or replace the defective
part. This warranty is extended to the original purchaser and any succeeding owner
with proper documentation of ownership for products purchased for residential use
within the United States of America.
WARRANTY U.S.A
6) Any repair, modification, alteration, or adjustment provided by any person not
authorized by TECNOGAS SUPERIORE.
7) Failure of the product if it is abused, misused or used for other than the
intended purpose or if used commercially/industrially.
8) Incorrect electric current, voltage or power supply.
9) Improper setting of any control.
10) Replacement of house fuses or resetting of circuit breakers.
11) Replacement of the light bulbs.
12) Wear and tear
13) Any substance, accumulating in any part or component of the product.
14) Damages to anything situated next to the product, including, but not limited to,
ceiling, floor or cabinetry.
15) Damage to the product caused by accident, fire, floods or acts of God.
16) Expenses for travel and transportation to locations more than 30 miles from an
authorized TECNOGAS SUPERIORE retailer.
17) Products with original serial numbers that have been removed.
The remedies described above are the only ones which TECNOGAS SUPERIORE will
provide, either under this warranty or under any warranty arising by operation of law.
TECNOGAS SUPERIORE will not be responsible for any consequential or incidental
damages arising from the breach of this warranty or any other warranty, whether
express, implied or statutory.
Some States do not allow the exclusion or limitation of incidental or consequential
damages. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. To know what your legal rights are,
consult your local state consumer affairs office or your state’s Attorney General.
30
461308462 07-2015
Electric diagram 30”
31
Electric diagram 36” 6 burners
32
461308462 07-2015
Electric diagram 36”4 burners + griddle
33
34
CONVERSION LABEL
INSTALLATION LABEL
Labels
35
461308462 07-2015
tecnogassuperiore.us
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising