Frigidaire | FFHD2250TS | Owner's Guide | Frigidaire FFHD2250TS Owner's Guide

All about the
Use & Care
of your
Refrigerator
TA B L E O F C O N T E N T S
Important Safety Instructions.......................2
Controls - Frigidaire Professional................23
Features At A Glance - Baseline Model..........4
Automatic Ice & Water Dispenser...............26
Features At A Glance - Gallery Model............5
Automatic Ice Maker - Freezer
(select models).........................................28
Features At A Glance - Pro Model.................6
Installation.................................................7
Installing Door Handles..............................14
Connecting the Water Supply.....................16
Controls - Frigidaire & Frigidaire
Gallery Dispenser......................................18
Controls - Non-Dispenser Models................21
www.frigidaire.com USA 1-800-944-9044
Storing Food and Saving Energy.................33
Normal Operating Sounds and Sights..........34
Changing the Filter....................................35
Care & Cleaning........................................37
Before You Call ........................................39
Major Appliance Warranty..........................44
www.frigidaire.ca Canada 1-800-265-8352
A05947004 (May 2018)
Door Removal Instructions.........................10
Storage Features.......................................29
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Please read all instructions before using this
refrigerator.
For your Safety
•
DO NOT store or use gasoline, or other
flammable liquids in the vicinity of this or
any other appliance. Read product labels
for warnings regarding flammability and
other hazards.
•
DO NOT operate the refrigerator in the
presence of explosive fumes.
•
Avoid contact with any moving parts of
automatic ice maker.
•
Remove all staples from the carton.
Staples can cause severe cuts, and also
destroy finishes if they come in contact
with other appliances or furniture.
Definitions
This is the safety alert symbol. It is
used to alert you to potential personal injury
hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.
DANGER
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result
in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
IMPORTANT
IMPORTANT indicates installation, operation
or maintenance information which is important but not hazard-related.
2
 Installation Checklist
Doors
 Handles are secure and tight
 Door seals completely to cabinet on all sides
Leveling
 Refrigerator is level side-to-side and
slightly elevated in front to assist with
door and drawer closing (front should be
higher than back)
 Toe grille is properly attached to refrigerator
 Cabinet is setting solid on all corners
Electrical Power
 House power turned on
 Refrigerator plugged in
Ice Maker
 House water supply connected to
refrigerator
 No water leaks present at all connections
- recheck in 24 hours
 Ice maker is turned ON
 Ice & water dispenser operates correctly
Final Checks
 Shipping material removed
 Fresh food and freezer temperatures set
 Crisper humidity controls set
 Registration card sent in
Child Safety
Destroy or recycle the carton, plastic bags, and
any exterior wrapping material immediately
after the refrigerator is unpacked. Children
should NEVER use these items to play.
Cartons covered with rugs, bedspreads, plastic
sheets or stretch wrap may become airtight
chambers, and can quickly cause suffocation.
Proper Disposal of your Refrigerator
or Freezer
Risk of child entrapment
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigerators or freezers are still dangerous
– even if they will sit for “just a few days”. If
you are getting rid of your old refrigerator or
freezer, please follow the instructions below to
help prevent accidents.
IMPORTANT SAFETY INSTRUCTIONS
Proper Disposal of Refrigerators/Freezers
•
We strongly encourage responsible appliance
recycling/disposal methods. Check with your utility
company or visit www.energystar.gov/recycle for
more information on recycling your old refrigerator.
Unplug the refrigerator before cleaning
and before replacing a light bulb to avoid
electrical shock.
•
Performance may be affected if the voltage
varies by 10% or more. Operating the
refrigerator with insufficient power can
damage the compressor. Such damage is
not covered under your warranty.
•
Do not plug the unit into an electrical
outlet controlled by a wall switch or pull
cord to prevent the refrigerator from
being turned off accidentally.
Before you throw away your old
refrigerator/freezer:
•
Remove doors.
•
Leave shelves
in place so
children may
not easily
climb inside.
•
Have
refrigerant
removed by
a qualified
service technician.
IMPORTANT
CFC/HCFC Disposal
Your old refrigerator may have a cooling system
that used CFCs or HCFCs (chlorofluorocarbons
or hydrochlorofluorocarbons). CFCs and HCFCs
are believed to harm stratospheric ozone if
released to the atmosphere. Other refrigerants
may also cause harm to the environment if
released to the atmosphere.
If you are throwing away your old refrigerator, make sure the refrigerant is removed for
proper disposal by a qualified technician. If
you intentionally release refrigerant, you may
be subject to fines and imprisonment under
provisions of environmental legislation.
Electrical information
•
The refrigerator must be plugged into its
own dedicated 115 Volt, 60 Hz., 15 Amp,
AC only electrical outlet. The power cord of
the appliance is equipped with a threeprong grounding plug for your protection
against electrical shock hazards. It must be
plugged directly into a properly grounded
three prong receptacle. The receptacle
must be installed in accordance with local
codes and ordinances. Consult a qualified
electrician. Avoid connecting refrigerator to
a Ground Fault Interrupter (GFI) circuit. Do
not use an extension cord or adapter plug.
•
If the power cord is damaged, it should
be replaced by an authorized service
technician to prevent any risk.
•
Never unplug the refrigerator by pulling on
the power cord. Always grip the plug firmly,
and pull straight out from the receptacle to
prevent damaging the power cord.
IMPORTANT
Pressing and holding the On/Off button for
three seconds, located on the temperature
control panel, will disable your refrigerator’s
cooling system but does not disconnect the
power to the light bulb and other electrical components. To turn off power to your
refrigerator you must unplug the power cord
from the electrical outlet.
Grounding type wall receptacle
Do not, under
any circumstances,
cut, remove,
or bypass the
grounding prong.
Power cord with
3-prong grounded plug
CAUTION
To avoid personal injury or property
damage, handle tempered glass shelves
carefully. Shelves may break suddenly if
nicked, scratched, or exposed to sudden
temperature change.
3
FEATURES AT A GLANCE - BASELINE MODEL
*Features may vary according to model
*Ice Bin
*Fresh Food
Ice Maker
Flipper Water
Guide Filter
Flipper
Mullion
Glass
Shelves
Glass
Shelves
Glass
Shelves
Crisper
Drawer
Deli
Drawer
Door Bin
Adjustable Hinges
*Freezer Ice Maker
Freezer Baskets
*Removable Ice Bin
Toe Grille
IMPORTANT
Features not purchased with your refrigerator can be purchased at www.frigidaire.com
or by calling 1-800-944-9044.
4
FEATURES AT A GLANCE - GALLERY MODEL
*Features may vary according to model
*Ice Bin
*Fresh Food Air
Ice Maker Filter
Flipper Water
Guide Filter
Flipper
Mullion
Glass
Shelves
Flip Shelf
Glass
Shelves
Crisper
Drawer
Deli
Drawer
Door Bin
Adjustable Hinges
*Freezer Ice
Maker
*Removable
Ice Bin
Freezer Baskets
Toe Grille
IMPORTANT
Features not purchased with your refrigerator can be purchased at www.frigidaire.com
or by calling 1-800-944-9044.
5
FEATURES AT A GLANCE - PRO MODEL
*Features may vary according to model
*Ice Bin
Flipper
*Fresh Food
Ice Maker Air Filter Guide
Dairy
Water
Flipper
Filter Compartment Mullion
Can
Dispenser
Flip Shelf
Glass Shelf
Glass Shelf
Crisper
Drawer
Deli
Drawer
Door Bin
Bottle Caddy
(Inside Drawer)
Adjustable Hinges
*Freezer Ice
Maker
*Removable
Ice Bin
Freezer Baskets
Toe Grille
IMPORTANT
Features not purchased with your refrigerator can be purchased at www.frigidaire.com
or by calling 1-800-944-9044.
6
INSTALLATION
Tools Necessary:
(OR)
Phillips Head
or
Quadrex Head
Screwdriver
AND
OR
AND
6mm
Allen Wrench
⅜" and ¼"
Socket
Wrench
Components Provided:
Top Hinge
Cover Front
Screw
Top Hinge
Cover Rear
Screw
Top Lower
Hinge Hinge
Screw Screw
This Use & Care Guide provides general
installation and operating instructions for
your model. We recommend using a service
or kitchen contracting professional to install
your refrigerator. Use the refrigerator only as
instructed in this Use & Care Guide. Before
starting the refrigerator, follow these
important first steps.
Location
•
Choose a place that is near a grounded,
non-GFCI, electrical outlet. Do Not use
an extension cord or an adapter plug.
•
If possible, place the refrigerator out of
direct sunlight and away from the range,
dishwasher, or other heat sources.
•
The refrigerator must be installed on a
floor that is level and strong enough to
support a fully loaded refrigerator.
•
Consider water supply availability for
models equipped with an automatic ice
maker.
OR
Adjustable
Wrench
⅜" Fixed
Wrench
CAUTION
Do Not install the refrigerator where the
temperature will drop below 55°F (13°C) or
rise above 110°F (43°C). The compressor
will not be able to maintain proper
temperatures inside the refrigerator.
Do Not block the toe grille on the lower front
of your refrigerator. Sufficient air circulation
is essential for the proper operation of your
refrigerator.
Installation
Allow the following clearances for ease
of installation, proper air circulation, and
plumbing and electrical connections:
Sides & Top
⅜ inch (9.5 mm)
Back
1 inch (25.4 mm)

NOTE
If your refrigerator is placed with the door
hinge side against a wall, you may have to
allow additional space so the door can be
opened wider.
Door opening
Your refrigerator should be positioned to allow
easy access to a counter when removing
food. For best use of refrigerator drawers and
freezer baskets, the refrigerator should be in a
position where both can be fully opened.
7
INSTALLATION
To raise: turn adjustment screw clockwise.
CAUTION
To lower: turn adjustment screw
counterclockwise.
Do Not loosen or remove these 3 hex screws.
Raise
DO NOT
Loosen
or
Remove
These 3
Hex
Screws
Anti-tip
Leg
Lower
3 Ensure both doors are bind-free with their
seals touching the cabinet on all four sides
and that cabinet is stable.
Cabinet Leveling & Refrigerator
Door Alignment (if necessary)
Guidelines for final positioning of your refrigerator:
•
All four corners of the cabinet must rest
firmly on the floor.
•
The front should be slightly elevated to
ensure that doors close and seal properly.
•
Doors should align with each other and
be level.
Most of these conditions can be met by raising
or lowering the adjustable front rollers.
To level the cabinet using the front rollers:
1 Slightly open freezer drawer if the toe grill
is installed. Lift the toe grille and gently
pull forward.
2 Make initial cabinet adjustments by using
the front roller height adjusting screws.
Use a 3/8 inch socket wrench to turn the
adjustment screws (1 per side).
8
4 After unit is leveled, lower anti-tip leg
using a 3/8 inch socket wrench until it
firmly contacts the floor.
5 Install the toe grille by fitting into place.
Toe Grille Must
Fit in Slot on
Anti-tip Bracket
Screw/Washer
Assembly
(2) Retaining Clips
INSTALLATION
To make final door height adjustments:
To adjust the flipper mullion:
1 Loosen the screw located on the flipper
mullion hinge.
Flipper
Mullion
Door
Door
Screw
1. Open freezer drawer to make lower hinge
visible.
2. Insert 6mm Allen wrench into the shaft of
the lower hinge.
3. Adjust the height by turning clockwise or
counterclockwise. Turning clockwise will
lower the door. Turning counterclockwise
will raise the door. Default setting is to
the lowest height when you receive your
appliance.
Flipper
Mullion
Hinge
Adjusting Flipper Mullion Screw
2 Adjust flipper mullion height. For proper
connection with the flipper mullion guide,
there should be a separation about the
thickness of a coin (0.060 inches, or
1.5 mm) between the guide and flipper
mullion.
Mullion
Guide
Raise
Flipper
Mullion
Thickness
of a Coin
Adjusting Flipper Mullion Height
3 Re-tighten screw.
9
DOOR REMOVAL INSTRUCTIONS
Getting through narrow spaces
If your refrigerator will not fit through an
entrance area, you can remove the doors.
Check first by measuring the entrance.
To prepare for removing the doors:
1 Make sure the electrical power cord is
unplugged from the wall outlet.
2 Open the freezer drawer and remove the
toe grille (see Installation section).
3 Remove any food from the door shelves
and close the doors.
To remove the top hinge covers:
1 Remove the two screws from each cover
over the top door hinges.
2 Lift inside edge of hinge cover and tilt
back.
Front
Cover Screw
Top Hinge
Cover
Hinge
Screws
DO NOT remove the ground screw from
hinge.
To remove the refrigerator doors
WARNING
Make sure the electrical power cord is
unplugged from the wall outlet.
1 Remove top hinge covers. Trace lightly
around the door’s top hinges with a pencil.
This makes reinstallation easier.
Rear
Cover
Screw
Top
Hinge
Leave
Hinge
With
Door
Left Door
Water
Line
Front
Cover Screw
Top Hinge
Cover
Top Ground
Hinge Screw
Hinge
Screws
Leave
Hinge
With
Door
Right Door
10
NOTE
Ground
Screw
Multi-wire
Cables
Rear
Cover
Screw

2 Disconnect the harness by grasping both
sides of the connector firmly, depress the
latch and pull apart.
DOOR REMOVAL INSTRUCTIONS

4 Open the refrigerator doors to a 90 degree
angle and remove the two screws from
the top hinge. Lift and remove door from
lower hinge.
NOTE
Top View
of
Cabinet
Top View
Cabinet
You will be pulling approximately five feet of
water tube from the back of the refrigerator.
NOTE
Use care while pulling the water tube from
the unit to be sure that you do not kink the
tube.
Left Door

90˚
Right Door
3 Detach the water tube from the connector
located behind the refrigerator, the
connector releases when you press inward
on the connector’s outer sleeve. Pull the
water tube out toward the front of the
unit.
CAUTION
Water
Line
Press
Be sure doors are set aside in a secure
position where they cannot fall and cause
personal injury, or damage to the doors or
handles.
5 Unscrew the three lower hinge screws and
remove the hinge.
Press
Water
Line
IMPORTANT
Open the refrigerator doors to a 90 degree
angle before lifting the doors off the bottom
hinges and setting them aside.
Lower Hinge Removal
11
DOOR REMOVAL INSTRUCTIONS
To reinstall the refrigerator
doors:
IMPORTANT
When replacing the doors on the lower
hinge, they must be installed at a 90 degree
angle.
1 Replace the lower hinge screws.
2 Holding the door at a 90 degree angle,
drop the pin down into the center hinge
opening. Rotate it slightly in either
direction until the door falls down into
place.
Pin
Mechanism
(Door Bottom)
Bottom
Hinge
Opening

NOTE
When reinserting the water tube and replacing the top hinge cover, use care to be sure
you do not kink the tube.

NOTE
Upon replacement, the tube needs to be
fully inserted up to the marking line.
5 Reconnect the harnesses.
6 Replace the top hinge covers.
7 Reconnect electrical power cord to the
wall outlet.
To reset door pin:
If doors are removed at less than a 40 degree
angle, the pin returns to the home position. It
can be reset by turning the door upside and
using a 5/32” Allen wrench to rotate the left
hand pin 90 degrees clockwise and the right
hand pin 90 degrees counterclockwise.
Doors
at 90º
3 Reinstall top hinge.
4 Insert the water line in the top left tunnel
pushing from the front to the back of the
unit.
Insert
tube up
to the
marking
line
Water
Line
om
ott
of
rs
oo
D
the
B
For
RIGHT DOOR,
turn pin 90˚
counterclockwise
For
LEFT DOOR,
turn pin 90˚
clockwise
Press
Press
Water
Line
12
Once the door pins are reset, follow the steps
“To reinstall the refrigerator doors”.
DOOR REMOVAL INSTRUCTIONS
Removing Freezer Drawer
CAUTION
Drawer is heavy. Use caution when lifting.

NOTE
To locate the pin, look inside the drawer
and the pin is next to the door liner and
the slides. Not all parts are shown in the
illustration.
1 Remove 4 hex head drawer screws.
2 Lift up drawer to remove.
DO NOT
Remove
Other
Screws
DO NOT
Loosen
or
Remove
These 3
Hex
Screws
Remove
Hex Head
Drawer Screw
Replacing Freezer Drawer
1 Extend the Freezer slides from the unit.
2 Carefully align support pin with hooks
on end of freezer slides and then lower
freezer door onto slides.
3 Replace the 4 hex head screws that secure
the slides to the door (2 on each side) and
tighten.
Pin
Hook
13
INSTALLING DOOR HANDLES
CAUTION
Wear gloves and safety goggles. Use extreme CAUTION when installing these handles.
Door Handle Mounting
Instructions for Frigidaire
& Frigidaire Gallery
Mounting Refrigerator Handles
1 Remove handles from carton
and any other protective
packaging.
2 Position fresh food handle
end caps over upper and
lower pre-installed shoulder
bolts (A) that are fastened
into door, ensuring the holes
for the set screws are facing
towards the opposite door.
3 While holding handle firmly
against door, fasten upper and
lower Allen set screws (B) with
supplied Allen wrench.
4 Repeat steps 2 and 3 to
install opposite handle.
Ensure the holes for the set
screws are facing towards the
Mounting Freezer Handle
first door.
5 Position freezer handle end
caps over left and right preinstalled shoulder bolts (A)
that are fastened to the door,
ensuring the holes for the set
screws are facing down.
6 While holding handle firmly
against door, loosely tighten
right Allen set screw (B) with
supplied Allen wrench until
there is no gap between
handle and door.
7 Still holding the handle firmly
to the door, firmly tighten
NOTE
left Allen set screw (B) with
supplied Allen wrench.
When tightening the Allen set screws, it is imperative that
8 Return to the right Allen set
force be applied to the longer arm of the Allen wrench
screw (B) and firmly tighten
supplied in the handle packaging.
with supplied Allen wrench.


NOTE
All set screws should be tightened so the screw is below the surface of the handle. The
handles should be drawn tight to freezer and refrigerator doors with no gaps. Opening the
opposite door while tightening the Allen screw makes installation easier.
The door handle may loosen over time or if it was installed improperly. If this happens,
tighten the set screws on the handles.
14
INSTALLING DOOR HANDLES
CAUTION
Wear gloves and safety goggles. Use extreme CAUTION when installing these handles.
Door Handle Mounting
Instructions for
Frigidaire Professional®
Mounting Refrigerator Handles
A
A
1 Remove handles from carton and
any other protective packaging.
2 Position fresh food handle end
over upper and lower preinstalled shoulder bolts (A) that
B
B
are fastened into door, ensuring
the holes for the set screws are
facing towards the opposite door.
3 While holding handle firmly
against door, fasten further
most upper and further most
B
B
lower Allen set screws (B) with
supplied Allen wrench.
4 Repeat steps 2 and 3 to install
opposite handle. Ensure the
holes for the set screws are
facing towards the first door.
A
A
5 Firmly tighten the inside Allen
set screws.
Mounting Freezer Handle
6 Position freezer handle end
over left and right pre-installed
handle shoulder bolts (A)
that are fastened to the door,
ensuring the holes for the set
screws are facing down.
7 While holding handle firmly
against door, loosely tighten
far right Allen set screw (B)
with supplied Allen wrench
until there is no gap between
handle and door.
8 Still holding the handle firmly
to the door, firmly tighten far
left Allen set screw (B) with
supplied Allen wrench.
NOTE
9 Return to the far right Allen set
screw (B) and firmly tighten
When tightening the Allen set screws, it is imperative that
with supplied Allen wrench.
force be applied to the longer arm of the Allen wrench
10 Firmly tighten the inside Allen
supplied in the handle packaging.
set screws.


NOTE
All set screws should be tightened so the screw is below the surface of the handle. The
handles should be drawn tight to freezer and refrigerator doors with no gaps. Opening the
opposite door while tightening the Allen screw makes installation easier.
The door handle may loosen over time or if it was installed improperly. If this happens,
tighten the set screws on the handles.
15
CONNECTING THE WATER SUPPLY
•
A shutoff valve to connect the water
supply line to your household water
system. DO NOT use a self-piercing type
shutoff valve.
•
Do not re-use compression fitting or use
thread seal tape.
•
A compression nut and ferrule (sleeve) for
connecting a copper water supply line to
the ice maker inlet valve.
WARNING
To avoid electric shock, which can cause
death or severe personal injury, disconnect
the refrigerator from electrical power before
connecting a water supply line to the
refrigerator.
CAUTION
To Avoid Property Damage:
• Copper or Stainless Steel braided tubing
is recommended for the water supply
line. Water supply tubing made of ¼
inch plastic is not recommended to be
used. Plastic tubing greatly increases
the potential for water leaks, and the
manufacturer will not be responsible for
any damage if plastic tubing is used for
the supply line.
• DO NOT install water supply tubing in
areas where temperatures fall below
freezing.
• Chemicals from a malfunctioning water
softener can damage the ice maker. If
your home has a water softening system,
ensure the softener is maintained and
working properly.
IMPORTANT
Ensure that your water supply line connections comply with all local plumbing codes.
Before Installing The Water
Supply Line, You Will Need:
•
Basic Tools: adjustable wrench, flat-blade
screwdriver, and PhillipsTM screwdriver
•
Access to a household cold water line
with water pressure between 30 and
100 psi.
•
A water supply line made of ¼ inch
(6.4 mm) OD, copper or stainless steel
tubing. To determine the length of tubing
needed, measure the distance from the
ice maker inlet valve at the back of the
refrigerator to your cold water pipe. Then
add approximately 7 feet (2.1 meters),
so the refrigerator can be moved out for
cleaning (as shown).
16

NOTE
Check with your local building authority
for recommendations on water lines and
associated materials prior to installing your
new refrigerator. Depending on your local/
state building codes, Frigidaire recommends
for homes with existing valves its Smart
Choice® water line kit 5305513409 with a
6 ft. (1.8 meters) Stainless Steel Water Line,
and for homes without an existing valve
Frigidaire recommends its Smart Choice®
water line kit 5305510264 with a 20 ft.
(6 meters) Copper Water Line with selftapping saddle valve. Please refer to
www.frigidaire.com/store for more information.
To Connect Water Supply Line To
Ice Maker Inlet Valve
1 Disconnect refrigerator from electric power
source.
2 Place end of water supply line into sink or
bucket. Turn ON water supply and flush
supply line until water is clear. Turn OFF
water supply at shutoff valve.
3 Remove plastic cap from water valve inlet
and discard cap.
4 If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve)
onto water supply line. Push water supply
line into water valve inlet as far as it
will go (¼ inch/6.4 mm). Slide ferrule
(sleeve) into valve inlet and finger tighten
compression nut onto valve. Tighten
another half turn with a wrench; DO NOT
over tighten. See Figure 1.
If you use braided flexible stainless steel
tubing - The nut is already assembled on
the tubing. Slide nut onto valve inlet and
finger tighten nut onto valve. Tighten
another half turn with a wrench; DO NOT
over tighten. See Figure 2.
CONNECTING THE WATER SUPPLY
5 With steel clamp and screw, secure water
supply line to rear panel of refrigerator as
shown.
6 Coil excess water supply line (copper
tubing only), about 2½ turns, behind
refrigerator as shown and arrange coils so
they do not vibrate or wear against any
other surface. Do not kink tubing.
7 Turn ON water supply at shutoff valve and
tighten any connections that leak.
8 Reconnect refrigerator to electrical power
source.
9 To turn ice maker on, lower wire signal
arm (freezer ice maker) or set the ice
maker’s On/Off power switch to the “On”
position (fresh food ice maker).

IMPORTANT
Your refrigerator’s water supply system
includes several tubing lines, a water filter,
and a water valve. To ensure that your
water dispenser works properly, this system
must be completely filled with water when
your refrigerator is first connected to the
household water supply line.
Plastic Water Tubing
to Ice Maker
Fill Tube
Braided
Flexible
Stainless
Steel
Water Line
NOTE
Water Valve
Bracket
These instructions do not cover after market
ice maker installation. Instructions in after
market ice maker kit should be used.
Steel
Clamp
Brass
Compression
Nut
Ferrule
(Sleeve)
Plastic Water
Tubing to Ice
Maker Fill
Tube
Copper
water line
Water Valve
Bracket
Steel
Clamp
Valve Inlet
Water Valve
6 ft (1.8 Meters) Braided flexible
stainless steel water line from
household water supply.
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
Figure 2
Valve Inlet
Water Valve
Copper water line
from household
water supply
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
Figure 1
17
CONTROLS - FRIGIDAIRE & FRIGIDAIRE
GALLERY DISPENSER
User Interface (colors and options may vary by model)
Enlarged view of above user interface display menu
(colors and options may vary by model)
18
CONTROLS - FRIGIDAIRE & FRIGIDAIRE
GALLERY DISPENSER
Options May Vary
Options
(∧ or ∨)
Used to enter and exit the
options menu and make
selections.
Exit
Toggles the options and run
modes.
Control
Locked
While in the locked state, you
will not be able to change any
settings on the display nor
dispense ice and water. The
“Control Locked” indicator will
flash and an audible warning
tone is played.
Quick
Freeze
On Off
Activates a faster rate for
freezing food and increases
ice production in the freezer.
Deactivates after 12 hours.
Ice Maker
On Off
Toggles the ice maker in the
refrigerator compartment
“ON” or “OFF”. In the “Off”
state, the indicator will blink
when ice is dispensed.
Display
On Off
Toggles the display of the
temperature settings On and Off.
Refrigeration
Temp
Allows the temperature setpoints to be adjusted. Control
temperatures range from
+33°F / +1°C to +47°F / +8°C.
Freezer
Temp
Allows the temperature setpoints to be adjusted. Control
temperatures range from -6°F
/ -21°C to +6°F / -15°C.
Mode
°F °C
Toggles display from
Fahrenheit to Celsius.
Light
Toggles dispenser light On
and Off.
Power Off
Press and hold for three seconds
to turn off the cooling system.
It also turns off the ice maker
and all dispenser functions. The
display will read “power off”.
Water
Filter
Displays the current status of
the water filter (Good, Order,
or Replace). To reset the filter
status to “Good”, press and hold
the “set” key for three seconds.
Air Filter
Displays the current status of
the air filter (Good, Order, or
Replace). To reset the filter
status to “Good”, press and hold
the “set” key for three seconds.
Default
Settings
While in the default option,
press and hold the “set” key
for three seconds to reset all
refrigerator settings to their
factory default settings.
Set (+ or −)
Selects the current menu
selection option.
Water
Press the “water” key to
select water. An indicator
light will be illuminated
above the active feature.
Cube
Press the “cube” key to
select cubed ice. An indicator
light will be illuminated
above the active feature.
Crush
Press the “crush” key to select
crushed ice. An indicator light
will be illuminated above the
active feature.
Setting cooling temperatures
(options may vary)

NOTE
The recommended settings for a product installed in a kitchen is 37˚F for the fresh food
compartment and 0˚F for the freezer.
IMPORTANT
If your product has food freezing in the fresh
food compartment, increase the temperature
setting 1 or 2 degrees.
IMPORTANT
If you place food within 1 inch in front of
the air ports, there may be the chance of
freezing food.
Air Port
19
CONTROLS - FRIGIDAIRE & FRIGIDAIRE
GALLERY DISPENSER

NOTE
Control features and alarms may vary by
model.
Alarms
Power Failure
In the event of a power failure, the power fail
alert will be illuminated. Press set to acknowledge the alarm. Other modes may be turned
off until the alarm is acknowledged. While
a power fail alert is displayed on the control
panel, the unit will continue normal operation.
The power fail alert on the control panel will
be removed once in the user acknowledges
the power fail condition by pressing any key on
the control panel. The high temp alarm may
also be illuminated until a safe operating range
temperature has been reached.
Freezer Temp
If the freezer temperature reaches 26°F or
greater, the alarm will sound and the temperature will flash. You can disable the alarm
by pressing the set key but the “High Temp”
indicator will illuminate until the temperature
goes below 26°F.
Fresh Food Temp
If the fresh food temperature reaches 55°F or
greater, the alarm will sound and the temperature will flash. You can disable the alarm
by pressing the set key but the “High Temp”
indicator will illuminate until the temperature
goes below 55°F.
Door Ajar
If the freezer or fresh food doors have been
left open for five minutes or more, an alarm
will sound and the door ajar indicator will
illuminate on the display. Press the set key to
reset any system alarms.
Flapper
When “Cube” or “Crush” is selected, if the flapper (or ice chute door) is being held open by a
jammed ice cube, an alarm will sound for two
minutes. The alarm will reset after two minutes
or when the ice cube is removed and the set
key is pressed to reset.
20
Sabbath Mode
The Sabbath Mode is a feature that disables
portions of the refrigerator and its controls
in accordance with observance of the weekly
Sabbath and religious holidays within the
Orthodox Jewish community.
Sabbath Mode is turned ON and OFF by
simultaneously pressing and holding both the
“∨” and “+” for five seconds. The display shows
“Sb” while in Sabbath mode.
In the Sabbath Mode, the High Temp alarm
is active for health reasons. For example,
if the door is left ajar the High Temp alarm
is activated. The refrigerator will function
normally once the door is closed, without
any violation of the Sabbath/Holidays. The
High Temp alarm is permitted when cabinet
temperature is outside the safe zone for 20
minutes. The alarm silences itself after 10
minutes while the High Temp icon stays lit until
the Sabbath mode is exited.
For further assistance, guidelines for proper
usage and a complete list of models
with the Sabbath feature, please visit
the web at
http:\\www.star-k.org.

NOTE
While in Sabbath Mode, neither the lights,
dispenser, nor the control panel will work
until Sabbath Mode is deactivated.
Refrigerator stays in Sabbath Mode after
power failure recovery. It must be deactivated with the buttons on the control panel.

NOTE
Although you have entered the Sabbath
Mode, the ice maker will complete the cycle
it had already initiated. The ice cube compartment will remain cold and new ice cubes
can be made with standard trays.
CONTROLS - NON-DISPENSER MODELS
User Interface In-Door Controls (options may vary)
IMPORTANT
Pressing the system on/off icon does not turn off power to your
refrigerator. You must unplug the power cord from the wall outlet.
An indicator light will be illuminated above most active features.
Touch the icon to activate the options below.
Power
On Off
Press and hold for three seconds to turn off the
cooling system to clean the refrigerator. The digital
displays will read OFF.
Default
Settings
Resets all refrigerator settings such as temp, temp
display and tones to their factory default settings.
Quick
Freeze
Activates a faster rate for freezing food.
Quick Ice
Temporarily increases cooling for freezer to increase
the production of ice
Air Filter
Filter condition status is always displayed when
door is open. Press and hold for three seconds to
reset after filter change.
Water
Filter
Press and hold for three seconds to reset after filter
change.
Alert
Reset
Tones emitted by each key press can be turned off
based on user preference. The sounds are muted
when the red indicator is lit. Warning signals will
stay active.
F/C
Touch to toggle display from Fahrenheit to Celsius.
Setting cooling temperatures
Press the + or − indicator to adjust the temperature to the desired
setting.
The temperature setting will begin to blink with the first touch. The
display will time out after 10 seconds and return to the basic display.

NOTE
The recommended settings for a product installed in a kitchen is
37˚F for the fresh food compartment and 0˚F for the freezer.
21
CONTROLS - NON-DISPENSER MODELS
Alarms
Door
Ajar
If the door has been left open for an
extended period of time, an alarm will
sound and the door ajar indicator will
display on the bottom display of the
control panel. The alarm is turned off
by closing the door. The alert reset key
will blink to prompt the reset of any
active alarms. Press this key to reset
any system alarms.
High In the event of a high temperature
Temp condition, the temperature display
will blink and display “HI”. After 20
minutes, the alarm will sound and the
high temp indicator will be red on the
bottom of the control panel. Upon
acknowledging the alarm, the highest
temperature reached will be displayed
and the refrigerator will resume normal
operation. In case the high temp alarm
is not acknowledged at the first alarm
sound time out, when the door is
first opened, the alarm sound will be
repeated.
Power In the event of a power failure, the
Fail
power fail alert will be displayed and
the temperature display will blink
until the alert reset icon is pressed,
acknowledging the alarm. Other
modes may be turned off until the
alarm is acknowledged. The power fail
alert is turned off and the refrigerator
will resume normal operation.
The high temp alarm may also be
illuminated until a safe operating range
temperature has been reached.
“Sabbath Mode”
The Sabbath Mode is a feature that disables
portions of the refrigerator and its controls for,
in accordance with observance of the weekly
Sabbath and religious holidays within the
Orthodox Jewish community.
Sabbath Mode is turned ON and OFF by
simultaneously pressing and holding the
freezer temp “-” and the refrigerator temp “+”
indicators for five seconds. The display shows
“Sb” while in Sabbath mode.
In the Sabbath Mode, the High Temp alarm
is active for health reasons. For example,
if the door is left ajar the High Temp alarm
is activated. The refrigerator will function
normally once the door is closed, without
any violation of the Sabbath/Holidays. The
22
High Temp alarm is permitted when cabinet
temperature is outside the safe zone for 20
minutes. The alarm silences itself after 10
minutes while the High Temp icon stays lit until
the Sabbath mode is exited.
For further assistance, guidelines for proper
usage and a complete list of models
with the Sabbath feature, please visit
the web at http:\\www.star-k.org.

NOTE
While in Sabbath Mode, neither the lights
nor the control panel will work until Sabbath
Mode is deactivated.
Refrigerator stays in Sabbath Mode after power
failure recovery. It must be deactivated with the
buttons on the control panel.

NOTE
During Sabbath Mode, the freezer ice maker
will continue to work and must be manually
turned off to be compliant with the Sabbath
observances.
CONTROLS - FRIGIDAIRE PROFESSIONAL
User Interface In-Door Controls (options may vary)
POWER
ON-OFF
Press and hold for three seconds
to turn off the cooling system. It
also turns off the ice maker and all
dispenser functions. The display will
read “OFF”.
DEFAULT
SETTINGS
Press and hold for three seconds to
reset all refrigerator settings to their
factory default settings.
ICE MAKER
ON-OFF
The Ice Maker is on if the LED
above the Icon is illuminated. Ice
dispensing will still function. Press
and hold the button for 3 seconds to
toggle the Ice Maker on and off.
POWERPLUS
FREEZE
Activates a faster rate for freezing
food and increases ice production
in the freezer. Deactivates after 12
hours.
AIR FILTER
Displays the current status of the air
filter (GOOD, ORDER, or REPLACE).
To reset the filter status to “GOOD”,
press and hold for three seconds.
WATER FILTER
Displays the current status of the
water filter (GOOD, ORDER, or
REPLACE). To reset the filter status
to “GOOD”, press and hold for three
seconds.
MUTE ALARM
Tones emitted by each key press
can be turned off based on user
preference. The sounds are muted
when the red indicator is lit. Warning
signals will stay active.
REFRIGERATOR
TEMP
Allows the temperature setpoints to be adjusted. Press the
“-” or “+” indicator to adjust the
temperature to the desired setting.
Control temperatures range from
+33°F / +1°C to +47°F / +8°C.
FREEZER TEMP
Allows the temperature setpoints to be adjusted. Press the
“-” or “+” indicator to adjust the
temperature to the desired setting.
Control temperatures range from
-6°F / -21°C to +6°F / -15°C.
C/F
Toggles display between Clesius and
Fahrenheit.
23
CONTROLS - FRIGIDAIRE PROFESSIONAL
Dispenser Controls
(options may vary)
Alarms
Power Failure
In the event of a power failure, the power fail
alert will be illuminated. Press “mute alarm”
to acknowledge the alarm. Other modes may
be turned off until the alarm is acknowledged.
While a power failure alert is displayed on the
control panel, the unit will continue normal
operation. The power fail alert on the control
panel will be removed once the user acknowledges the power fail condition by pressing any
key on the control panel. The high temp alarm
may also be illuminated until a safe operating
range temperature has been reached.
Freezer Temp
WATER
Press the “WATER” key to
select water.
CUBES
Press the “CUBES” key to
select cubed ice.
CRUSHED
Press the “CRUSHED” key to
select crushed ice.
light
Toggles dispenser light on
and off.
If the freezer temperature reaches 26°F or
greater, the alarm will sound and the temperature will flash and the dispenser control
will display “HIGH TEMP DETECTED”. You can
disable the alarm by pressing “mute alarm” but
the “HIGH TEMP DETECTED” indicator will illuminate until the temperature goes below 26°F.
Fresh Food Temp
If the fresh food temperature reaches 55°F or
greater, the alarm will sound and the temperature will flash and the dispenser control
will display “HIGH TEMP DETECTED”. You can
disable the alarm by pressing “mute alarm” but
the “HIGH TEMP DETECTED” indicator will illuminate until the temperature goes below 55°F.
Door Ajar
If the freezer or fresh food doors have been
left open for five minutes or more, an alarm
will sound and the door ajar indicator will illuminate on the display. Press “mute alarm” to
reset any system alarms.
Flapper
When “CUBES” or “CRUSHED” is selected, if
the flapper (or ice chute door) is being held
open by a jammed ice cube, an alarm will
sound for two minutes and the current selection will blink on the dispenser control. The
alarm will reset after two minutes or when the
ice cube is removed.
24
CONTROLS - FRIGIDAIRE PROFESSIONAL
Sabbath Mode
The Sabbath Mode is a feature that disables
portions of the refrigerator and its controls
in accordance with observance of the weekly
Sabbath and religious holidays within the
Orthodox Jewish community.
Sabbath Mode is turned ON and OFF by
simultaneously pressing and holding both
the freezer “-” and the refrigerator “+” for
five seconds. The display shows “Sb” while in
Sabbath mode.

NOTE
During Sabbath Mode, the freezer ice maker
will continue to work and must be manually
turned off to be compliant with the Sabbath
observances.
In the Sabbath Mode, the High Temp alarm
is active for health reasons. For example,
if the door is left ajar the High Temp alarm
is activated. The refrigerator will function
normally once the door is closed, without
any violation of the Sabbath/Holidays. The
High Temp alarm is permitted when cabinet
temperature is outside the safe zone for 20
minutes. The alarm silences itself after 10
minutes while the High Temp icon stays lit until
the Sabbath mode is exited.
For further assistance, guidelines for proper
usage and a complete list of models
with the Sabbath feature, please visit
the web at
http:\\www.star-k.org.

NOTE
While in Sabbath Mode, neither the lights,
dispenser, nor the control panel will work
until Sabbath Mode is deactivated.
Refrigerator stays in Sabbath Mode after
power failure recovery. It must be deactivated with the buttons on the control panel.

NOTE
Although you have entered the Sabbath
Mode, the ice maker will complete the cycle
it had already initiated. The ice cube compartment will remain cold and new ice cubes
can be made with standard trays.
25
AUTOMATIC ICE & WATER DISPENSER
Priming the water supply system Turning the fresh food ice maker
on and off
CAUTION
Ice production is controlled by the ice maker’s
For proper dispenser operation, recommended
water supply pressure should fall between
30 psi and 100 psi. Excessive pressure may
cause the system to malfunction.
1 Begin filling the system by pressing and
holding a drinking glass against the water
dispenser
paddle.
2 Keep the glass
in this position
until water
comes out of
the dispenser.
It may take
about 1½
minutes.
3 Continue
dispensing
Dispenser
water for
(varies by model)
about four
minutes to flush the system and plumbing
connections of any impurities (stopping to
empty the glass as necessary).

NOTE
The water dispenser has a built-in device that
shuts off the water flow after three minutes
of continuous use. To reset this shutoff device, simply release the dispenser paddle.

NOTE
Dispensed water is not chilled. For colder
water, add ice to cup or container before
dispensing water.
Ice maker operation & care
After the refrigerator is installed properly and
has cooled for several hours, the ice maker can
produce ice within 24 hours. The ice maker will
fill the ice bin from the rear. You must dispense
some ice to force the ice forward in the bin.
This will allow the bin to fill completely.
Ice Maker and Storage Bin Capacity
This ice maker should produce 2.0 to 2.5
pounds of ice per 24 hours.
In a Standard Depth model, the ice bin will hold
about 6.5 pounds of ice. In a Counter Depth
model, the ice bin will hold about 4 pounds of ice.
26
On/Off feature on the control panel. Pressing
the On/Off feature turns the ice maker on &
off.
IMPORTANT
Turning off the ice maker simply disables
ice making. You will still be able to dispense
existing ice, and you will still be able to
dispense water.

NOTE
The ice maker also has a built-in plastic
signal arm that automatically stops ice production when the ice bin is full. This signal
arm should not be used to manually stop
the ice maker.
Using the ice maker after installation
Before making ice for the first time, be sure
to prime the water supply system. Air in new
plumbing lines can result in two or three empty
ice maker cycles. Furthermore, if the system
is not flushed, the first ice cubes may be
discolored or have an odd flavor.
IMPORTANT
Your ice maker is turned on at the factory so
it can work as soon as you install your refrigerator. If you cannot connect a water supply,
set the ice maker’s On/Off feature to Off;
otherwise, the ice maker’s fill valve may make
a loud chattering noise when it attempts to
operate without water.
IMPORTANT
On occasion, unusually small ice cubes may be
noticed in the bucket or in dispensed ice. This
could occur in normal operation of the ice maker. If you start seeing these more frequently,
it may be an indication of low water pressure
or the water filter needs to be replaced. As the
water filter nears the end of its useful life and
becomes clogged with particles, less water is
delivered to the ice maker during each cycle.
Remember, if it’s been six months or longer
since you last changed your water filter, replace
the water filter with a new one. Poor quality
household water may require the filter to be
changed more frequently.
AUTOMATIC ICE & WATER DISPENSER
Ice maker/dispenser tips
•
•
4 Allow the ice bin to dry completely before
replacing in the freezer.
If your refrigerator is not connected to a
5
Replace the ice bin. Turn the ice maker on.
water supply or the water supply is turned
off, turn off the ice maker as described in
Remove and empty the ice bin if:
the previous section.
• An extended power failure (one hour
The following sounds are normal when
or longer) causes ice cubes in the ice
the ice maker is operating:
bin to melt and refreeze together after
- Motor running
power is restored, jamming the dispenser
mechanism.
- Ice dropping into ice bin
- Water valve opening or closing
- Running water
•
If you need a large quantity of ice at one
time, it is best to get cubes directly from
the ice bin.
•
Ice cubes stored too long may develop an
odd flavor. Empty the ice bin as explained
below.
•
You do not use the ice dispenser
frequently. Ice cubes will freeze together
in the bin, jamming the dispenser
mechanism.
Remove the ice bin and shake to loosen the
cubes or clean as explained above.
CAUTION
•
When dispensing cubed ice, it is normal
to have a small quantity of little pieces
along with the whole cubes.
NEVER use an ice pick or similar sharp
instrument to break up the ice. This could
damage the ice bin and dispenser mechanism.
•
To avoid splashing, dispense ice into your
container before adding liquids.
•
It is normal for ice to fill to the top of the
ice bin.
To loosen stuck ice, use warm water.
Before replacing the ice bin, make sure it is
completely dry.
CAUTION
If the water supply to your refrigerator is
softened, be sure the softener is properly
maintained. Chemicals from a water softener
can damage the ice maker.
Cleaning the ice maker
Clean the ice
maker and ice
bin at regular
intervals,
especially prior
to vacation or
moving.
IMPORTANT
When removing or replacing the ice bin,
avoid rotating the auger in the ice bin. If
the auger is accidentally rotated, you must
realign the auger by turning it in 45 degree
turns (see below) until the ice bin fits into
place with the drive mechanism. If the
auger is not properly aligned when replacing
the ice bin, the refrigerator will not dispense
ice. The fresh food door also may not close
properly causing warm air to leak into the
fresh food compartment.
1 Turn off
the ice
maker.
2 Remove
the ice bin
by pulling
straight out.
Removing Ice Bin
3 Empty and carefully clean the ice bin
with mild detergent. Do not use harsh or
abrasive cleaners. Rinse with clear water.
Auger
Adjusting Ice Bin Auger
27
AUTOMATIC ICE MAKER - FREEZER
(SELECT MODELS)
Operation & Care of the Freezer
Ice Maker (select models)
Ice maker tips
• The following sounds are normal when
the ice maker is operating:
After the refrigerator is installed properly, the
ice maker can produce ice within 24 hours.
- Motor running
When using the ice maker for the first time, and
- Ice dropping into ice bin
in order for it to work properly, it is necessary
- Water valve opening or closing
to clear air from the water tubing and the filter.
Furthermore, if the system is not flushed, the
- Running water
first ice cubes may be discolored or have an odd • Ice cubes stored too long may develop an odd
flavor. Once the ice maker begins making ice,
flavor. Empty the ice bin as explained below.
allow the bin to fill completely, then discard the
first FULL bin of ice on a Standard Depth model, Quick Freeze Function
and the first TWO FULL bins of ice on a Counter
Your refrigerator is equipped with a Quick
Depth model.
Freeze Function for freezing food at a faster
Ice Maker and Storage Bin Capacity rate, but it can also increase ice production.
This function terminates automatically after 12
This ice maker should produce between 2 and hours. This function affects only the ice
2.5 pounds of ice per 24 hours depending on
maker in the freezer.
usage conditions. In a Standard Depth model,
the ice bin will hold about 12 pounds of ice. In
a Counter Depth model, the ice bin will hold
CAUTION
about 7 pounds of ice.
IMPORTANT
Your ice maker is turned on at the factory
so it can work as soon as you install your
refrigerator. If you cannot connect a water
supply, lift the ice maker’s wire signal arm
to turn it off. Otherwise, the ice maker’s
fill valve may make a loud chattering noise
when it attempts to operate without water.
If the water supply to your refrigerator is
softened, be sure the softener is properly
maintained. Chemicals from a water softener
can damage the ice maker.
Cleaning the ice maker
Clean the ice maker and ice bin at regular
intervals, especially prior to vacation or moving.
1 Turn off the ice maker.
2 Remove the ice bin.
Turning the ice maker on and off
3 Empty and carefully clean the ice bin
with mild detergent. Do not use harsh or
The ice maker is turned off and on by lifting/
abrasive cleaners. Rinse with clean water.
lowering the ice maker’s wire signal arm. To gain
4 Allow the ice bin to dry completely before
access to the ice maker, pull the freezer drawer
replacing in the freezer.
out. Lift the wire signal arm to turn the ice maker
OFF and lower the wire signal arm to turn it ON.
5 Replace the ice bin. Turn the ice maker on.
Remove and empty the ice bin if an extended
power failure (one hour or longer) causes
ON
ice cubes in the ice bin to melt and refreeze
together after power is restored.
Remove the ice bin and shake to loosen the
cubes or clean as explained above.
OFF
Wire
Signal Arm
28
CAUTION
NEVER use an ice pick or similar sharp
instrument to break up the ice. This could
damage the ice bin.
To loosen stuck ice, use warm water.
Before replacing the ice bin, make sure it is
completely dry.
STORAGE FEATURES
CAUTION
To avoid personal injury or property
damage, handle tempered glass shelves
carefully. Shelves may break suddenly if
nicked, scratched, or exposed to sudden
temperature change. Allow the glass shelves
to stabilize to room temperature before
cleaning. Do not wash in dishwasher.
 NOTE
Features may vary according to model.
You can easily adjust shelf positions in the
fresh food compartments to suit your needs.
The shelves have mounting brackets that
attach to slotted supports at the rear of each
compartment.
Change the Position of a Shelf
1 Remove all food from shelf.
Reposition the Air Seal
For crisper shelves:
1 Remove air seal by pushing down on the
flap with a downward rotation.
2 Position the air seal towards the outside
end of the shelf to avoid the air tower
when shelf is pushed back into place.
3 Install seal by sliding lower tab of seal up
into bottom rear slot of shelf with seal at a
downward angle then pulling up on seal flap
until seal sits snug on back of shelf and flap sits
at about a 10 degree angle from shelf surface.
For glass shelves:
1 Remove air seal by pushing seal straight back.
2 Position the air seal towards the outside
edge of the shelf to avoid the air tower
when shelf is pushed back into place.
3 Install seal by sliding the open channel end
of the seal onto back edge of shelf until seal
sits snug on back of shelf and flap sits at
about a 10 degree angle from shelf surface.
2 Lift the front edge up and pull the shelf
out.
3 Replace by inserting the mounting bracket
hooks into the desired support slots.
4 Lower the shelf and lock into position.
IMPORTANT
Be aware of the air seal located at the rear of
the shelf. Shelves located on the left side should
have the air seal mounted on the far left side.
Shelves located on the right side should have
the air seal mounted on the far right side. This
is to ensure there is no interference with the
large air tower on the back wall of the cabinet.
This also applies to the crisper shelves.
Flip Shelf
29
STORAGE FEATURES
Drawers
Your refrigerator includes a variety of storage
drawers.
2 Lift the front slightly and remove the
drawer.
Crispers
Crisper drawers are designed for storing fruits,
vegetables, and other fresh produce.
Removing Crisper Drawer
Deli drawer
Ideal for storage of deli meats, cheese, and
beverages.
Opening Crisper Drawer
Crisper humidity control
Crisper drawers include a sliding control for
adjusting the humidity inside the crisper. Leafy
vegetables keep best when stored with the
Humidity Control set on Higher Humidity. Fresh
fruits keep best when stored with the Humidity
Control set on Lower Humidity.
Vegetables
Fruits
Humidity Control
Higher
Humidity
Lower
Humidity
Adjusting Crisper Humidity
To remove the Crisper Drawer for
cleaning:
1 Pull the drawer out until it stops.
Doors
Storage bins (varies by model)
The doors to your fresh food compartment use
a system of modular storage bins. All of these
bins are removable for easy cleaning. Some of
them have fixed positions, while others can be
adjusted to your needs.
Door bins are ideal for storing jars, bottles,
cans, and large drink containers. They also
enable quick selection of frequently used
items.
To change the position of an adjustable
door bin:
1 Remove all food from door bin.
2 Grip the bin firmly with both hands and lift
it upward.
3 Remove the bin.
4 Place the bin just above desired position.
30
STORAGE FEATURES
5 Lower the bin onto supports until locked in Dairy
place.
compartment
Use the dairy
compartment,
at the top of
the fresh food
compartment
door, for shortterm storage
of cheese,
spreads, or
Dairy Compartment
butter. The dairy
compartment is designed to be warmer than the
open area and includes a lift-up cover and a dairy
divider (select models).
Freezer Features (varies by model)
Adjustable Door Bin
Clip
6 Place bin liner into bin.
Stabilizer
Bar
Freezer Baskets
To Remove Upper Freezer Basket
Accessories (varies by model)
Removable Can Dispenser
The can dispenser holds six (12 ounce) cans.
Insert cans into top of bin and dispense from
the bottom.
Can Dispenser
1 Find the side where the basket frame is
aligned to the clip opening. The basket frame
should be aligned to both front and rear clips
on the same side (either left or right side).
2 If the basket frame is not aligned to the left or
right side, push the basket sideways (to either
side) until it is aligned.
3 By grabbing the basket wire frame close to the
frontal clip, pull up to take the basket frame out.
4 Grab the basket frame close to the rear clip
and pull up until it comes out of the clip.
5 Once one side of the basket is off the clips or
retainers, slide the basket sideways until the
other side of the frame is aligned with the clip
openings on the opposite side of the freezer.
6 In the same way, pull up the basket frame
from the frontal and rear clips until it is
out of the clips.
7 Remove the basket.
Reverse the steps to reinstall the basket.
31
STORAGE FEATURES
Dividers Removal
 NOTE
If basket is not resting on stabilizer bar retainer
clips, the drawer will not close properly.
Removing Freezer Basket
Instructions
1 Locate the basket clips in the rear corners
of the basket and pull them out to remove.
2 Open fresh food doors completely.
Lift up on the front of the upper divider and
pull out.
Upper Basket
Divider
Retainers
3 Lift the basket up and remove.
Replacing Freezer Basket
Instructions
1 Place freezer basket back inside the
freezer drawer.
2 Replace clips by sliding them back into the
slots.
Stabilizer
Bar
Upper Basket Divider
Location of
basket clip.
One each side.
Squeeze handle and lift up in the center of the
divider to move it side-to-side. (The divider
cannot be removed.)
Lower Basket
Divider
Pull to Remove
Plastic Lower Basket Divider
Tilt Wire Shelf
The freezer tilt wire shelf (located on the inside
of the freezer drawer) is not designed to be
removed.
Push to Replace
32
STORING FOOD AND SAVING ENERGY
Ideas for storing foods
•
Activating “quick freeze” also will help
your freezer more efficiently maintain the
selected temperature after placing new
purchases with pre-existing frozen foods.
•
Avoid adding too much warm food to the
freezer at one time. This overloads the
freezer, slows the rate of freezing, and
can raise the temperature of frozen foods.
•
Leave a space between packages, so cold
air can circulate freely, allowing food to
freeze as quickly as possible.
Fresh food storage
•
Keep the fresh food compartment
between 34°F and 40°F with an optimum
temperature of 37°F.
•
Avoid overcrowding the refrigerator
shelves, which reduces air circulation and
causes uneven cooling.
•
Avoid placing food in front of air ports.
(See Controls Section for illustration.)
Fruits and vegetables
•
Store fruits and vegetables in crisper
drawers, where trapped moisture helps
preserve food quality for longer time
periods.
•
Wash items and remove excess water.
•
Wrap any items that have strong odors or
high moisture content.
Ideas for saving energy
Installation
•
Locate the refrigerator in the coolest part
of the room, out of direct sunlight, and
away from heating ducts or registers.
•
Do not place the refrigerator next to
heat-producing appliances such as a
range, oven, or dishwasher. If this is not
possible, a section of cabinetry or an
added layer of insulation between the
two appliances will help the refrigerator
operate more efficiently.
•
Level the refrigerator so that the doors
close tightly.
Meat
•
Wrap raw meat and poultry separately
and securely to prevent leaks and
contamination of other foods or surfaces.
•
Use the deli drawer to store meat/poultry
for short-term storage. Any meat to be
kept longer than two days should be
frozen.
Frozen food storage
•
Keep the freezer compartment at 0°F or
lower.
•
A freezer operates most efficiently when it
is at least ⅔ full.
Packaging foods for freezing
•
To minimize food dehydration and quality
deterioration, use aluminum foil, freezer
wrap, freezer bags, or airtight containers.
Force as much air out of the packages as
possible and seal them tightly. Trapped air
can cause food to dry out, change color,
and develop an off-flavor (freezer burn).
•
Wrap fresh meats and poultry with
suitable freezer wrap prior to freezing.
•
Do not refreeze meat that has completely
thawed.
Loading the freezer
•
Temperature settings
•
Refer to the “Controls” section for
procedures on temperature settings.
Food storage
•
Avoid overcrowding the refrigerator or
blocking cold air vents. Doing so causes
the refrigerator to run longer and use
more energy.
•
Cover foods and wipe containers dry
before placing them in the refrigerator.
This cuts down on moisture build-up
inside the unit.
•
Organize the refrigerator to reduce door
openings. Remove as many items as
needed at one time and close the door as
soon as possible.
•
Do not place a hot container directly on
a cold shelf. Remember, such an extreme
temperature change may damage the
glass.
Prior to grocery shopping, activate
“quick freeze” so that on your return
you can ensure your newly purchased
food designated for the freezer will be
preserved as quickly as possible.
33
NORMAL OPERATING SOUNDS AND SIGHTS
Understanding the sounds you
may hear
Your new, high-efficiency refrigerator may
introduce unfamiliar sounds. These sounds
normally indicate your refrigerator is operating
correctly. Some surfaces on floors, walls, and
kitchen cabinets may make these sounds more
noticeable.
The following is a list of major components
in your refrigerator and the sounds they can
cause:
A Evaporator Refrigerant through the
evaporator may create a boiling or
gurgling sound.

NOTE

NOTE
Energy efficient foam in your refrigerator is
not a sound insulator.
During automatic defrost cycle, a red glow in
the back wall vents of your freezer compartment is normal.
B Evaporator fan You may hear air being
forced through the refrigerator by the
evaporator fan.
C Defrost heater During defrost cycles,
water dripping onto the defrost heater
may cause a hissing or sizzling sound.
After defrosting, a popping sound may
occur.
D Automatic ice maker When ice has
been produced, you will hear ice cubes
falling into the ice bin. Ice maker fan,
water valve activation, and refrigerant gas
fluid may create sounds from its operation.
E Electronic control & automatic
defrost control These parts can produce
a snapping or clicking sound when turning
the cooling system on and off.
K
F Condenser fan You may hear air being
forced through the condenser.
G Compressor Modern, high-efficiency
compressors run much faster than older
models. The compressor may have a highpitched hum or pulsating sound.
H Water valve Makes a buzzing sound each
time it opens to fill the ice maker.
I Drain pan (not removable) You may hear
water dripping into the drain pan during
the defrost cycle.
J Condenser May create minimal sounds
from forced air.
K Motorized damper May produce a light
humming during operation.
L Ice dispensing paddle When dispensing
ice, you will hear a snapping, clicking, or
popping sound.
34
Features vary by model
CHANGING THE FILTER
Air filter
(Frigidaire Gallery/Professional)
The air filter is located at the top of the air
tower.
Replacing your PureAir Ultra IITM
air filter
To ensure optimal filtering of refrigerator
odors, you should change the air filter every
six months (the filter status light on the Touch
Panel prompts you to replace the filter after six
months).
1 Insert fingers in circled area.
2 Push clips in to release front cover.
3 Remove front cover by pulling towards you
and lifting up.
4 Replace air filter by sliding into slots.
5 Installation of front cover is reverse of
removal.
6 To reset Air Filter status, refer to
instructions under “Controls Section”.
Ordering replacement filters
Order new filters by calling 877-808-4195,
online at www.frigidaire.com/store, or through
the dealer where you bought your refrigerator.
You may want to consider ordering extra filters
when you first install your refrigerator.
Air Filter Replacement cartridge,
part #PAULTRA2
35
CHANGING THE FILTER
Locating the Filters
Your refrigerator is equipped with water
filtering system. The water filter system filters
all dispensed drinking water, as well as the
water used to produce ice.
More about your Advanced
Water Filter
The PureSource Ultra IITM
ice and water filter system is
tested and certified to NSF/ANSI
Standards 43, 53 and 401 for the
reduction of claims specified on
the performance data sheet.
Water Filter
The water filter is located at the top right side
of the fresh food compartment.
Replacing the Water Filter
In general, you should change the water
filter every six months to ensure the highest
possible water quality. Water Filter Status
on the user interface prompts you to replace
the filter after a standard amount of water
(125 gallons/473 liters for PureSource
Ultra IITM) has flowed through the system.
If your refrigerator has not been used for a period
of time (during moving for example), change the
filter before reinstalling the refrigerator.
Filter Cartridge
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before or after the system. Systems
certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
Test & certification results:
•
•
•
•
•
Rated Capacity - 125 gallons/473 liters for
PureSource Ultra IITM ice and water filter
Rated service flow - .65 gallons per minute
Operating Temp: Min. 33°F, Max. 100°F
Maximum Rated Pressure - 100 pounds
per square inch
Recommended Minimum Operating
Pressure: 30 pounds per square inch
To replace your PureSource Ultra IITM
water filter:
Ordering Replacement Filters
To order your replacement filters, please visit
our online store at www.frigidaire.com/store,
by calling toll-free at 1-800-599-7569, or by
visiting the dealer where you purchased your
refrigerator. Frigidaire recommends that you
order extra filters when you first install your
refrigerator, and that you replace your filters at
least once every six months.
Here is the product number to request when
ordering:
PureSource Ultra IITM Water Filter
Part #EPTWFU01

NOTE
When ordering your replacement filter,
please reorder the same filter type that is
currently in your refrigerator.
36
It is not necessary to turn the water supply off
to change the filter. Be ready to wipe up any
small amounts of water released during the
filter replacement.
1 Turn Off the ice maker power switch.
2 Remove the old filter by rotating it counterclockwise (to the left) 90 degrees to release it.
3 Slide the old filter cartridge straight out of
the housing and discard it.
4 Unpackage the new filter cartridge. Slide it
into the filter housing as far as it will go with
the grip end horizontal.
5 Push lightly inward on the filter while rotating
it clockwise (to the right). The filter will then
pull itself inward as it is rotated. Rotate the
filter 90 degrees until it stops and the grip
end is vertical. You may be able to feel a very
light click as the filter locks into place.
6 Press a drinking glass against the water
dispenser while checking for any leaks at
the filter housing. Any spurts and sputters
that occur as the system purges air out of
the dispenser system are normal.
7 Continue dispensing water for 3-4 minutes
or until 1.5 gallons of water has flowed
through the system. You will likely need to
empty and refill your glass several times.
8 Turn On the ice maker.
9 Press and hold the Water Filter reset
button on the control panel for three
seconds. When the display changes from
Red to Green, the status has been reset.
CARE & CLEANING
Protecting your investment
Keeping your refrigerator clean maintains its appearance and prevents odor build-up. Wipe up
any spills immediately and clean the freezer and fresh food compartments at least twice a year.

NOTE
Do not use abrasive cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches, or cleansers containing petroleum
products on plastic parts, interior doors, gaskets, or cabinet liners. Do not use paper towels,
scouring pads, or other abrasive cleaning materials.
•
•
•
•
Never use metallic scouring pads, brushes, abrasive cleaners, or strong alkaline solutions on any
surface.
Never use CHLORIDE or cleaners with bleach to clean stainless steel.
Do not wash any removable parts in a dishwasher.
Always unplug the electrical power cord from the wall outlet before cleaning.

NOTE
If you set your temperature controls to turn off cooling, power to lights and other electrical
components will continue until you unplug the power cord from the wall outlet.
•
•
•
Remove adhesive labels by hand. Do not use razor blades or other sharp instruments which
can scratch the appliance surface.
Do not remove the serial plate. Removal of your serial plate voids your warranty.
Before moving your refrigerator, raise the anti-tip brackets so the rollers will work correctly.
This will prevent the floor from being damaged.
Refer to the guide on the next page for details on caring and cleaning specific areas of your refrigerator.
CAUTION
• Pull the refrigerator straight out to move it. Shifting it from side to side may damage
flooring. Be careful not to move the refrigerator beyond the plumbing connections.
• Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or
damp hands.
IMPORTANT
If you store or move your refrigerator in freezing temperatures, be sure to completely drain
the water supply system. Failure to do so could result in water leaks when the refrigerator is
put back into service. Contact a service representative to perform this operation.
Vacation and moving tips
Occasion Tips
Short
• Leave refrigerator operating during vacations of three weeks or less.
Vacations • Use all perishable items from refrigerator compartment.
• Turn automatic ice maker off and empty ice bucket, even if you will only be
gone a few days.
Long
• Remove all food and ice if you will be gone one month or more.
Vacations • Turn the cooling system off (see “Controls” section for location of On/Off
button) and disconnect power cord.
• Turn water supply valve to closed position.
• Clean interior thoroughly.
• Leave both doors open to prevent odors and mold build-up. Block doors open
if necessary.
Moving
• Remove all food and ice.
• If using a handcart, load from the side.
• Adjust rollers all the way up to protect them during sliding or moving.
• Pad cabinet to avoid scratching surface.
37
CARE & CLEANING
Part
Interior & Door
Liners
Door Gaskets
Drawers & Bins
Glass Shelves
Toe Grille
Care & Cleaning Tips
What To Use
Tips and Precautions
• Soap and water
Use two tablespoons of baking soda in one
• Baking soda and water quart of warm water. Be sure to wring
excess water out of sponge or cloth
before cleaning around controls, light
bulb or any electrical part.
• Soap and water
Wipe gaskets with a clean soft cloth.
• Soap and water
Use a soft cloth to clean drawer runners and
tracks.
• Soap and water
Allow glass to warm to room temperature
before immersing in warm water.
• Glass cleaner
• Mild liquid sprays
• Soap and water
• Mild liquid sprays
• Vacuum attachment
Exterior &
Handles
• Soap and water
Exterior &
Handles
• Soap and water
(Stainless Steel
Models Only)
• Non Abrasive Glass
Cleaner
• Stainless Steel
Cleaners
Vacuum dust from front of toe grille. Remove
toe grille (see Installation Instructions). Vacuum
backside, wipe with sudsy cloth or sponge.
Rinse and dry.
Do not use commercial household cleaners
containing ammonia, bleach or alcohol to clean
handles. Use a soft cloth to clean smooth
handles. DO NOT use a dry cloth to clean
smooth doors.
Never use CHLORIDE or cleaners with
bleach to clean stainless steel.
Clean stainless steel front and handles with
non-abrasive soapy water and a dishcloth.
Rinse with clean water and a soft cloth. Use
a non-abrasive stainless steel cleaner. These
cleaners can be purchased at most home
improvement or major department stores.
Always follow manufacturer’s instructions.
Do not use household cleaners containing
ammonia or bleach.
NOTE: Always clean, wipe and dry with
the grain to prevent scratching. Wash the
rest of the cabinet with warm water and mild
liquid detergent. Rinse well, and wipe dry with
a clean soft cloth.
38
BEFORE YOU CALL
1-800-944-9044 (United States)
1-800-265-8352 (Canada)
Concern Potential Cause
Automatic Ice Maker
Ice maker is
not making
any ice.
Visit our web site at
www.frigidaire.com
Common Solution
•
Ice maker is turned off.
•
Turn on ice maker. For the fresh food
ice maker, press ice maker on-off button
once. For the freezer ice maker, lower
the arm to turn the ice maker on, or
raise it and snap it in its upper position
to turn the ice maker off.
•
Refrigerator is not
connected to water line or
water valve is not open.
•
Connect the unit to the household water
supply and ensure the water valve is
open.
•
The water supply line is
kinked.
•
Ensure that the supply line does not
kink when the refrigerator is pushed into
place against the wall.
•
The water filter is not
seated properly.
•
Remove and re-install the water filter.
Be sure to seat it fully into the locked
position.
•
The water filter may be
clogged with foreign
material.
•
If water dispenses slowly or not at all, or
if the filter is six months old or older, it
should be replaced.
•
Freezer ice maker wire
signal arm is being held
up by an item not allowing
it to go in the on or down
position.
•
Move any item or frozen ice cubes that
may block the signal arm from being in
the on or down position. Additionally,
the ice bin itself may be out of position
so that it prevents the signal arm from
dropping all the way down. Be sure the
bin is pushed all the way to the rear
of the shelf. See Automatic Ice MakerFreezer section in manual.
39
BEFORE YOU CALL
Concern Potential Cause
Automatic Ice Maker (Cont’d)
Ice maker is
not making
enough ice.
Freezer ice
maker will
not stop
making
ice (select
models).
Ice cubes
are freezing
together.
40
Common Solution
•
Ice maker is producing less
ice than you expect.
•
The ice maker will produce approximately
2.0 to 2.5 pounds of ice every 24 hours
depending on usage conditions.
•
The water filter may be
clogged with foreign
material.
•
If water dispenses slower than normal,
or if the filter is six months old or older,
it should be replaced.
•
The water supply line is
kinked.
•
Ensure that the supply line does not
kink when the refrigerator is pushed into
place against the wall.
•
Saddle valve on cold water
pipe is clogged or restricted
by foreign material.
•
Turn off household water line valve.
Remove valve. Clean valve. Replace
valve if necessary.
•
Heavy traffic, opening
or closing of the doors
excessively.
•
Press Fast Freeze to temporarily increase
ice production rate. (Freezer ice maker
only.)
•
Freezer control is set too
warm (freezer ice maker).
•
Set freezer control to colder setting to
improve performance of the ice maker
(freezer ice maker). Allow 24 hours for
temperature to stabilize.
•
Water pressure is extremely
low. Cut-off and cut-on
pressures are too low (well
systems only).
•
Have someone turn up the cut-off and
cut-on pressure on the water pump
system (well systems only).
•
Reverse osmosis system is
in regenerative phase.
•
•
Ice maker wire signal arm
is being held down by a
package in the freezer
that has fallen against ice
maker.
•
It is normal for a reverse osmosis
system to be below 20 psi during the
regenerative phase.
Move any item or frozen ice cubes that
may block the signal arm from being
in the off or upward position. See
Automatic Ice Maker-Freezer section in
manual.
•
Ice cubes are not being
used frequently enough or
interruption of power for
prolonged time.
•
Remove ice container and discard ice.
The ice maker will produce fresh supply.
Ice should be used at least twice weekly
to keep the cubes separated.
•
Ice cubes are hollow (shells
of ice with water inside).
The hollow cubes break
open in the bin and leak
their water onto existing
ice, which causes it to
freeze together.
•
This generally occurs when the ice
maker does not get enough water. This
is usually the result of a clogged water
filter or restricted water supply. Replace
the water filter and if the condition still
occurs check for a clogged Saddle Valve,
water valve not turned on all the way or
kinked water supply line.
BEFORE YOU CALL
Concern Potential Cause
Dispenser (Ice & Water)
Dispenser will
not dispense
ice.
Common Solution
•
There is no ice in the bin to
be dispensed.
•
See the “Ice maker is not making any
ice” section above.
•
The refrigerator doors are
not completely closed.
•
Be sure the refrigerator doors are
completely closed.
•
Dispenser paddle has
been pressed too long and
the dispenser motor has
overheated.
Ice has melted and frozen
around auger due to
infrequent use, temperature
fluctuations, and/or power
outages.
•
The motor overload protector will reset
in about three minutes and then ice can
be dispensed.
•
Remove ice container, thaw, and empty
the contents. Clean container, wipe dry,
and replace in proper position. When
new ice is made, dispenser should
operate.
Ice cubes are jammed
between ice maker and
back of ice container.
Water filter not seated
properly.
•
Remove ice cubes that are jamming the
dispenser.
•
Remove and reinstall the water filter. For
Puresource Ultra II, be sure to rotate it
to the right until it stops and the grip
end is vertical.
•
Water filter is clogged.
•
Replace filter cartridge. Be sure to rotate
it to the right until it stops and the grip
end is vertical.
•
Household water line valve
is not open.
•
Water not
cold enough.
•
•
Water has
an odd taste
and/or odor.
•
The water dispensing
system is not designed to
chill water.
Water has not been
dispensed for an extended
period of time.
Open household water line valve. See
CONCERN column AUTOMATIC ICE
MAKER.
Add ice to cup or container before
dispensing water.
•
Draw and discard 10-12 glasses of water
to freshen the supply.
Unit not properly connected
to cold water line.
•
Connect unit to cold water line that
supplies water to the kitchen faucet.
Ice dispenser
is jammed.
•
•
Dispenser will
not dispense
water.
•
•
41
BEFORE YOU CALL
Concern Potential Cause
Common Solution
Opening/Closing Of Doors/Drawers
Door(s) will
not close.
Drawers are
difficult to
move.
•
Door was closed too hard,
causing other door to open
slightly.
•
Close both doors gently.
•
Refrigerator is not level.
It rocks on the floor when
moved slightly.
•
Ensure floor is level and solid, and can
adequately support the refrigerator.
Contact a carpenter to correct a sagging
or sloping floor.
•
Refrigerator is touching a
wall or cabinet.
•
•
Food is touching shelf on
top of drawer.
•
Ensure floor is level and solid, and can
adequately support the refrigerator.
Contact a carpenter to correct a sagging
or sloping floor.
Remove top layer of items in drawer.
•
Track that drawers slide on
is dirty.
•
Ensure drawer is properly installed on
track.
•
Clean drawer, rollers, and track. See
Care & Cleaning.
Running of Refrigerator
Compressor
does not run.
Refrigerator
seems to run
too much or
too long.
•
Freezer control is set to
“OF”.
•
Set freezer control.
•
Refrigerator is in defrost
cycle.
•
This is normal for a fully automatic
defrost refrigerator. The defrost cycle
occurs periodically, lasting about 30
minutes.
•
Plug at electrical outlet is
disconnected.
•
Ensure plug is tightly pushed into outlet.
•
House fuse blown or
tripped circuit breaker.
•
Check/replace fuse with a 15 amp timedelay fuse. Reset circuit breaker.
•
Power outage.
•
•
Your variable speed
compressor is designed
to run 100% of the time
except during the defrost
cycle. At times it will run
faster, such as after a
defrost cycle.
•
Check house lights. Call local electric
company.
It is normal for the compressor to run
continuously except during defrost
mode.
Digital Temperature Setting Display
Digital
temperature
displays an
error.
42
•
Electronic control system
has detected a performance
problem.
•
Call your Electrolux service
representative, who can interpret any
messages or number codes flashing on
the digital displays.
BEFORE YOU CALL
Concern Potential Cause
Common Solution
Water/Moisture/Frost Inside Refrigerator
Moisture
collects on
inside of
refrigerator
walls.
•
Weather is hot and humid.
•
The rate of frost buildup and internal
sweating increases.
•
Flipper mullion
•
Water collects
on bottom
side of drawer
cover.
Water collects
in bottom of
drawer.
•
Vegetables contain and
give off moisture.
•
Adjust flipper mullion. (See “To adjust
the flipper mullion” in the Installation
section.)
It is not unusual to have moisture on the
bottom side of the cover. Move humidity
control (some models) to lower setting.
•
Washed vegetables and
fruit drain while in the
drawer.
•
Water collecting in bottom of drawer is
normal. Dry items before putting them
in the drawer or store produce in tightly
sealed bags to help reduce condensation
inside of the drawer.
Water/Moisture/Frost Outside Refrigerator
Moisture
collects on
outside of
refrigerator
or between
doors.
•
Weather is humid.
•
This is normal in humid weather. When
humidity is lower, the moisture should
disappear.
Food in Fresh Food Compartment
Food is
freezing.
•
Temperature setting is too
low.
•
Move the setting to a higher degree.
•
Temperature sensor is
covered by food (right side
of fresh food area).
•
Allow space for air flow to the sensor.
•
Food is covering the air
ports.
•
Allow space between the air ports and
the food.
43
MAJOR APPLIANCE WARRANTY
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove
to be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside
the USA or Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,
shelves, etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other
consumables, or knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry
trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not
limited to floors, cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other
than genuine Electrolux parts or parts obtained from persons other than authorized service
companies; or external causes such as abuse, misuse, inadequate power supply, accidents,
fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE
YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH
AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS
WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty
period should service be required. If service is performed, it is in your best interest to obtain and
keep all receipts. Service under this warranty must be obtained by contacting Electrolux at the
addresses or phone numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by
Electrolux Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada,
your appliance is warranted by Electrolux Canada Corp. Electrolux authorizes no person to change
or add to any obligations under this warranty. Obligations for service and parts under this warranty
must be performed by Electrolux or an authorized service company. Product features or specifications
as described or illustrated are subject to change without notice.
USA
1.800.944.9044
Frigidaire
10200 David Taylor Drive
Charlotte, NC 28262
44
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising