Blomberg | DWT55100SS | Use and Care Manual | Blomberg DWT57500FBI Use and Care Manual

Dishwasher
Use and Care Manual
FOR MODELS
DW 55100 B (ADA Height)
DW 55100 FBI (ADA Height)
DW 55100 SS (ADA Height)
DW 55100 W (ADA Height)
DWT 54100 B
DWT 54100 FBI
DWT 54100 SS
DWT 54100 W
DWT 54400 SS ULTRA
DWT 54400 W ULTRA
DWT 55100 B
DWT 55100 FBI
DWT 55100 SS
DWT 55100 W
DWT 55200 BWS
DWT 55200 FBIWS
USA
DWT 55200 SSWS
DWT 55200 WWS
DWT 55500 SS
DWT 57500 B
DWT 57500 FBI
DWT 57500 SS
DWT 57500 W
DWT 57550 SS
To prevent accidents, which could cause serious injury or death, as well as
machine damage read these instructions before installation and / or use.
Contents
1. IMPORTANT SAFETY INSTRUCTIONS
1
2. INSTALLATION
3
3. GETTING TO KNOW YOUR DISHWASHER
4
4. LOADING THE DISHWASHER
5
4.1 UPPER RACK
4.2 LOWER RACK
4.3 PROPER AND IMPROPER LOADING OF DISHWARE
6
7
10
5. WHAT SHOULD NOT BE WASHED IN YOUR DISHWASHER
11
6. OPERATING THE DISHWASHER
12
7. DETERGENT & RINSE AID DISPENSER
15
7.1 FILLING THE DETERGENT DISPENSER
7.2 FILLING RINSE AID DISPENSER
15
16
8. SETTING THE WATER SOFTENER
17
9. FILLING THE DISHWASHER SALT DISPENSER
18
10. CARE AND MAINTENANCE
19
10.1 CARING FOR YOUR DISHWASHER EXTERIOR
10.2 CARING FOR YOUR DISHWASHER INTERIOR
19
19
11. TROUBLE SHOOTING
22
12. TECHNICAL FEATURES
28
13. WARRANTY STATEMENT FOR THE BLOMBERG
DISHWASHERS
29
14. HOW TO GET SERVICE
30
1. IMPORTANT SAFETY
INSTRUCTIONS
INTRODUCTION
Please read this user manual and
particularly the safety instructions
completely and carefully. They will save you
time and effort and help to ensure optimum
dishwasher performance.
WARNING
When using the dishwasher, follow
basic precautions, including the
following:
Read all instructions before using the
dishwasher! Save these operating
instructions and pass them on to any
future user.
• Use the dishwasher only for its intended
purpose as described in this user
manual. This appliance is intended for
normal household use only.
• The manufacturer disclaims
responsibility for damage or injury
caused by improper use of this
appliance.
• The information in this user manual must
be followed to minimize the risk of fire
or explosion and to prevent property
damage, personal injury or loss of life.
• Do not operate your dishwasher unless
all the enclosure panels are properly in
place.
• Do not tamper with the controls.
• Do not abuse, sit on, stand in or on the
door or dish rack of the dishwasher.
• The cup racks are designed to support
cups, glasses and kitchen utensils. When
the cup racks are in the dishwasher
do not lean on or use the cup racks to
support your body weight.
• To reduce the risk of injury, do not
allow children to play in, on or near the
dishwasher.
• Use only detergents or rinse aids
recommended for use in a household
dishwasher and keep them in a dry place
out of the reach of children. Check that
the detergent dispenser is empty after
the completion of each wash program.
• Dishwasher detergents are alkaline.
They can be dangerous if inhaled or
swallowed. Avoid contact with skin
and eyes and keep children and infirm
persons away from the dishwasher
Be sure to observe all listed warnings and
cautions. Look particularly for the icons with
exclamation marks inside. The information
icon will also provide important references.
WARNING
Ý
CAUTION
Notice
WARNING:
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION :
Indicates a potentially hazardous situation
which, if not avoided, may result in injury.
It may also be used to alert against unsafe
practices.
Notice :
Indicates a potentially hazardous situation
which, if not avoided, may result in damage
to the dishwasher, the table-ware, the
equipment or the environment.
1
USA
•
•
•
•
•
•
•
•
•
when the door is opened. Consult a
doctor immediately if detergent has been
swallowed or inhaled.
Do not drink water from the dishwasher!
Harmful residues could be present.
Under certain conditions hydrogen gas
may be produced in a hot water heater
system that has not been used for
two weeks or more. Hydrogen gas is
explosive. If the hot water system has not
been used for such period, before using
the dishwasher turn on all hot water
taps and let the water flow from each for
several minutes. This will release any
accumulated hydrogen gas. As gas is
flammable, do not smoke or use an open
flame during this time.
Do not store or use flammable liquids or
vapors in the area of the dishwasher.
When loading items to be washed,
position sharp items so that they are
not likely to damage the door seal and
load sharp knives with the handles up to
reduce the risk of cut-type injuries.
Do not wash plastic items unless they
are marked “dishwasher safe” or the
equivalent. For plastic items not so
marked, check the manufacturer’s
recommendations.
If a malfunction occurs, switch off the
appliance and turn off the water supply to
the dishwasher.
Before cleaning or carrying out
maintenance, switch off the appliance,
disconnect the power plug and turn off
the water supply.
Repairs and technical modifications must
be carried out exclusively by a qualified
technician.
If the dishwasher is not in use for an
extended period of time (i.e. vacation
home), we recommend you check that
the baskets are empty, leave the inside
of the dishwasher clean, leave the door
cracked open to allow air to circulate and
turn off both the power and water supply
to the dishwasher.
2
• This appliance must be grounded. In the
event of a malfunction or breakdown,
grounding will reduce the risk of electric
shock by providing a path of least
resistance for electric current. This
appliance is equipped with a cord having
an equipment-grounding conductor and
a grounding plug. The plug must be
plugged into an appropriate outlet that
is installed and grounded in accordance
with all local codes and ordinances.
• This appliance must be connected to
a grounded metal, permanent wiring
system, or an equipment-grounding
conductor must be run with the circuit
conductors and connected to the
equipment-grounding terminal or lead on
the appliance.
WARNING
• Improper connection of the
equipment-grounding conductor
can result in a risk of electric shock.
Check with a qualified electrician
or service representative if you are
in doubt whether the appliance is
properly grounded. Do not modify
the plug provided with the appliance,
if it will not fit the outlet, have a
proper outlet installed by a qualified
electrician.
SAVE THESE INSTRUCTIONS
USA
2. INSTALLATION
WARNING
Danger of suffocation!
Ensure that any plastic wrappings, bags,
WARNING
small pieces etc. are disposed of safely
When installing the dishwasher, follow
and kept out of the reach of children.
basic precautions, including the
• Remove the door to the washing
following:
compartment when removing an old
• The dishwasher installation must be
dishwasher from service or discarding it.
performed in accordance with the
Ensure that the appliance presents no
installation manual. If you did not receive
danger to children while being stored for
an installation manual order it by calling
disposal.
1-800-459-9848 or you may also download
•
Old appliances may contain materials
it from our web site at
that can be recycled. Please contact
www.blombergappliances.com
your local recycling authority about the
• Installation, maintenance and repair should
possibility of recycling these materials.
be performed by a qualified installer. Work
by unqualified persons could be dangerous
and may void the warranty.
• Do not operate the appliance if damaged,
malfunctioning, partially disassembled or if
it has missing or broken parts.
• Before installation or service, disconnect
the power supply to the work area by
unplugging the unit, “tripping” the circuit
breaker or removing the fuse.
• Only connect the dishwasher to the power
supply when all installation and plumbing
work is complete.
• Do not install or store the dishwasher
where it can be exposed to below freezing
temperatures or exposed to weather.
• Dishwasher must be secured to adjacent
cabinetry using the brackets provided.
Failure to do this may cause damage to
property or bodily injury.
• Connect to a properly rated, protected
and sized power supply circuit to avoid
electrical overload. The dishwasher is
designed for an electrical supply of 120 V
(volts), 60 Hz (hertz), AC, connected to a
dishwasher-dedicated, properly grounded
electrical circuit with a fuse or breakers
rated for 15 amperes. Electrical supply
conductors shall be a minimum of # 16
AWG copper wire rated at 75 °C (167 °F)
or higher. These requirements must be met
to prevent injury and machine damage.
Consult a qualified electrician if in doubt.
• Do not use any extension cord or portable
outlet device to connect the dishwasher to
a power supply.
3 USA
3. GETTING TO KNOW YOUR DISHWASHER
FOR MODELS
DW 55100 B (ADA Height)
DW 55100 FBI (ADA Height)
DW 55100 SS (ADA Height)
DW 55100 W (ADA Height)
DWT 54100 B
DWT 54100 FBI
DWT 54100 SS
DWT 54100 W
DWT 54400 SS ULTRA
DWT 54400 W ULTRA
DWT 55100 B
DWT 55100 FBI
DWT 55100 SS
DWT 55100 W
DWT 55200 BWS
DWT 55200 FBIWS
DWT 55200 SSWS
DWT 55200 WWS
DWT 55500 SS
DWT 57500 B
DWT 57500 FBI
DWT 57500 SS
DWT 57500 W
DWT 57550 SS
15
14
1
2
3
4
8
9
10
11
5
6
12
7
DWx xxxxx xxxxx
UF5
1. Upper rack
2. Upper spray arm
3. Salt container (model depending)
4. Cutlery basket
5. Detergent dispenser
6. Door
7. Control panel
8. Guiding track for the upper rack
9. Lower spray arm
10. Filters
11. Lower rack
12. Model and Serial Tag
13. Turbo fan heat drying system (model depending)
14. Removable 3rd basket (model depending)
15. Additional upper spray arm (model depending)
4
USA
13
4. LOADING THE
DISHWASHER
CAUTION
• Large knives and other utensils with
sharp tips and edges must be placed
horizontally into the upper rack due
to risk of injury. Other smaller knives
and sharp utensils should be placed
with sharp side down in the cutlery
basket.
• Use extreme caution when removing
knives and other sharp utensils from
the dishwasher. These items may
have shifted position during the wash
program, and may be wet or slippery.
• The cup racks are designed to
support cups, glasses and kitchen
utensils. When the cup racks are in
the dishwasher do not lean on or use
the cup racks to support your body
weight.
1. Pull the handle to open the door. If
the door is opened during operation, the
dishwasher will stop running. Once the
door is closed the program will continue.
Upper rack
MODEL DEPENDING
Top rack load pattern for 12 place
settings according to the AHAM
DW-1 Standards
Notice :
• 3rd basket should be removed out
of the dishwasher during the tests
according to AHAM DW-1.
• Your dishwasher holds a maximum of 12
place settings.
• Place all containers such as cups,
glasses and pots into the dishwasher
with the opening facing downwards (so
that no water can collect).
• Small and light items can go into the
upper rack.
• Long and narrow items are placed in the
middle of the racks.
• Place all large and very dirty items in the
lower rack.
• Dishes and cutlery should not be placed
above each other.
• Glasses should not touch each other.
• The movement of the spray arms must
not be hindered.
• Do not overload your dishwasher
and pay attention to manufacturer
instructions regarding dishes which are
appropriate for use in for a dishwasher.
Only with suitable dishes (mentioned
in section 5) will you obtain optimal
washing results with a sensible use of
energy.
CAUTION
Hot steam can escape! Danger of
serious burns or other injury.
2. Remove coarse food leftovers from
tableware.
3. Now you can load the dishwasher.
Lower rack
Bottom rack load pattern for 12
place settings according to the
AHAM DW-1 Standards
5
USA
4.1 UPPER RACK
Load the upper rack with dessert plates,
cups, glasses etc.
B
4.1.1 HEIGHT SETTING
(MODEL DEPENDING)
In certain models, the height setting of
the upper rack may be changed using the
wheels which are present at two height
levels.
C
4.1.2 VARIABLE HEIGHT SETTING
(MODEL DEPENDING)
The upper rack is equipped with a lifting
mechanism which enables you to change
the height of the rack even if it is fully
loaded, and without having to remove it
from the dishwasher.
CAUTION
Make sure that the rack is empty.
Changing the height setting while the
rack contains tableware could cause the
contents to dislodge, causing personal
injury or damage to the tableware.
LIFT UPPER RACK
1. To lift the upper rack to a higher position,
hold it on one side and carefully pull it
upwards A.
2. To lift the opposite side of the rack, hold
it and pull it upwards in the same manner.
1. Release the latches on both the right
and left tracks of the upper rack by turning
them to the outside A.
2. Pull out the rack completely B.
3. Place the rack into the tracks again at
the desired height C.
4. Push the latches back into the correct
position.
A
A
6
USA
LOWER UPPER RACK
1. To lower the upper rack, hold and press
in the rack lever on one side and carefully
lower the rack without releasing the lever B.
2. Repeat the procedure with the lever on
the opposite side of the rack.
4.1.4 ADJUSTABLE SHELVES (MODEL
DEPENDING)
Depending on the size of the glasses
and cups, the shelf height setting may be
adjusted.
1. Fold the shelf upwards A.
2. Positioning at the desired height B.
3. Fold the shelf again downwards C.
Notice :
Make sure that both levers catch in the
same height position.
C
B
A
4.2 LOWER RACK
Use the lower rack for plates, bowls, pots
etc.
B
4.1.3 FOLDING TINES
(MODEL DEPENDING)
There are “folding tines” in the upper rack
to allow you more space to accommodate
glasses or cups.
Simply pull in the first front folding tine,
move it to left A and right B to place in
another positon. When you need, take the
tines down until the tines fall down.
A
4.2.1 FOUR FOLDING PLATE SUPPORT
TINES (MODEL DEPENDING)
There are 4 separate “folding plate support
tines” in the lower rack of your dishwasher
designed to allow you more space to
accommodate saucepans, pots and large
bowls in the lower rack. You can either fold
each section (1, 2, 3, 4). individually or, all
at once, to create a large empty space.
B
7
USA
1
to remove the dishes from the basket and
place them separately into the kitchen
drawers or shelves.
2
3
Simply press the handgrips A and fold them
down. Pull tines up to fold them up again.
A
If you don’t want to use the Removable 3rd
basket, pull it back to yourself to remove
it from the machine, rotate the rail lids A
towards outside and pull them towards
yourself to take them out. After taking out
the basket by lifting it up, remove the carrier
part from the rails by pulling it towards
yourself. Replace the rail lids and push
them back to seat them into their places.
Turn the rails inside the machine outwards
B to seat them properly in their places.
A
Notice :
When finished, test to ensure that the spray
arm can still move freely.
4.2.2 REMOVABLE 3rd BASKET
(MODEL DEPENDING)
The Removable 3rd basket is designed for
small dishes, or long dishes that cannot fit
into the cutlery basket.
B
In order to put the Removable 3rd basket
back into its place, repeat the same
process in reverse order.
Thanks to the easy take-out feature,
it allows removing the dishes from the
machine together with the basket after
washing operation. Since it can fit into all
standard size drawers, there is no need
8
USA
4.2.3 SLIDING CUTLERY BASKET
Designed to allow free placement of the
B
A
dishes according to their size, the Sliding
Cutlery Basket can slide over the tines to
the left A and right B side.
Use the basket inset C for your cutlery so
C
that all items in the basket are surrounded
by a sufficient water flow.
For larger items (e.g. wire whisks) the
basket inset may be removed C. Simply
raise.
To make loading easier, the cutlery basket
can be removed. Simply take out basket
upward.
Place long items such as ladles, cooking
spoons etc. on the shelf in the upper rack.
Notice :
When finished, test to ensure that the spray
arm can still move freely.
9
USA
4.3 PROPER AND IMPROPER LOADING OF DISHWARE
Notice :
1
2
3
4
5
6
1: Salad Fork
2: Teaspoon
3: Dinner fork
4: Knife-solid handle
5: Serving spoon
6: Serving fork
6
2
4
4
3
2
2
2
1
1 2
4
4
3
3
3
3
2
4
3
2
4
2
2
1
1
1
2
2 1
2
1
1 2
2 1
1
1
4
2
2 2
2
2 2
1
4
3
5
2
2
3
5
4
2
2
4
3
3
4
3
3
4
Sliding Cutlery Basket load
pattern for 12 place settings
according to the AHAM DW-1
Standards
• Place all large and
very dirty items in the
lower rack.
• Place all containers
such as cups,
glasses and pots into
the dishwasher with
the opening facing
downwards (so that
no water can collect).
• The movement of the
spray arms must not
be hindered.
• Do not overload your
dishwasher. Dishes
and cutlery should
not be placed above
each other. Glasses should not touch.
• Only with suitable dishes (mentioned in section 5) will you obtain optimal washing results
with a sensible use of energy.
incorrect
incorrect
incorrect
incorrect
10
USA
• Disposable plastics and disposable
aluminum cannot withstand high
temperatures; do not wash them in the
dishwasher.
5. WHAT SHOULD NOT
BE WASHED IN YOUR
DISHWASHER
Notice :
• Rust-sensitive steel parts like iron and
cast iron that can rust and stain other
utensils and damage the interior stainless
steel liner of the dishwasher and void
the warranty. Do not wash copper, brass,
pewter, bronze or tin.
• Cutlery with wooden or horn handles and
cutlery with mother-of-pearl or porcelain
handles will deteriorate over time if put in
the dishwasher.
• Plastics may lose their shape or color
with hot water, please follow the
instructions of plastic manufacturers.
Be sure that plastic items are marked
"dishwasher safe".
• Glued dishes or cutlery are not suitable
for machine washing since certain
adhesives may get soft or dissolve with
hot water.
• Aluminum may fade over time. Minerals
in water and detergent may cause the
aluminum to darken or spot.
• Sterling silver articles should not be
washed in the dishwasher because they
tend to discolor and become dull by
dishwasher detergent.
• Silverware and stainless steel items
should not be in contact with each other.
Mixing these items can cause staining.
Remove and hand dry these items
immediately when the program ends.
• Decorated glasses, porcelain, fine china
and china with gold rims are sensitive to
machine washing. They may lose their
patterns and colors over time.
• Crystal and very fine glassware may
become opaque (etch) losing their shine
over time. You may prefer to wash them
by hand.
• Do not wash sponges or dish cloths in
dishwasher.
• Do not wash art and craft articles in
dishwasher.
11
CAUTION
• If in doubt, wash by hand or follow the
instructions from the manufacturer of
utensils, dishes, glasses or pots and
pans.
• Do not wash items soiled with
cigarette ash, candle wax, varnish,
paints or chemicals since they can
damage your dishwasher.
Notice :
We recommend when buying new
dishware, try to choose ones that are
suitable for machine washing (marked as
dishwasher safe).
CARING FOR YOUR TABLE-WARE
The combination of high temperatures and
dishwasher detergent may cause damage
to some items if they are washed in the
dishwasher. Remember, if there is any
doubt about any aspect concerning items
to be washed in the dishwasher, follow the
instructions from the manufacturer of the
items, or wash the items by hand.
USA
6. OPERATING THE DISHWASHER
Reset.
3 sec.
1 On/Off button
2 Half Load indicator led
3 Salt level indicator led *
4 Start/Pause/Cancel indicator led
5 Start/Pause/Cancel button
6 Time Delay button
7 Time Delay indicator led
8 Rinse aid level indicator led
9 Remaining Time Indicator/Delay Time
Indicator
Reset.
3 sec.
10 Tablet Detergent indicator
11 Program Indicator
12 Half Load/Combi Tablet button
13 Program Selection buton
(* Model depending)
HOW TO USE YOUR DISHWASHER:
1. Open the door and load the dishwasher.
2. Check that both upper and lower spray
arms move freely.
3. Pour correct amount of detergent into the
detergent dispenser and close the lid.
4. Push in the On/Off button 1 and check
that the display lights come on.
5. Check the rinse aid level indicator led. 8
If necessary, refill rinse aid.
6. Check the salt level indicator led. 3 If
necessary, refill salt. (model depending)
7. Use the Program Selection button 13 to
choose your washing program.
- When there are few dishes, additionally
use the Half Load function.
- Depending on the hardness level of
the tap water, the Tablet Detergent
function allows better drying and washing
performance from the multi-purpose tablets.
8. Start the program with the Start/Pause/
Cancel button 5.
9. Close the door and the program will start.
10. When the wash program has ended, an
electronic beep will sound and will continue
every 10 seconds. After 2 minutes of
elapsed time the sound will stop. The beep
can also be stopped by opening the door or
by pressing the On/Off buton 1.
11. Press the On/Off button 1 and open the
door after the program is completed. The
indicator lights will go off.
12
12. Allow your dishes to cool for 15 minutes,
with the door open.
13. Unload the dishes. Begin with the lower
rack.
CAUTION
Avoid opening the door during the
washing process. This interrupts the
washing process, and hot steam will
escape. Hot steam can cause burns and
other serious injuries. When the door is
closed, the program will continue.
FUNCTION BUTTONS
ON/OFF BUTTON
Turn the dishwasher on with the
On/Off button. When turning on,
the icon on the display module of
the last used program will light up.
PROGRAM SELECTION
BUTTON
Use the Program Selection
button to select the desired
program. The icon of the corresponding
program will light up.
Refer to “Table of Programme Data and
Average Consumption Values” to select a
programme suitable for your dishes. Select
the desired programme with programme
selection button.
USA
HALF LOAD/TABLET
DETERGENT BUTTON
Half Load/Tablet Detergent
Button allows you to turn on
and off the Half Load and Tablet Detergent
functions of your machine.
WARNING
HALF LOAD FUNCTION
If you want to run your machine without
loading it completely, place your dishes
into the machine as you desire. Press On/
Off button to turn on your machine. Press
the Half Load/Tablet Detergent button after
selecting the desired programme until Half
Load Indicator lights up, then press Start/
Pause/Cancel button and close the door
of your machine. With the Half Load option
you can use every part of your lower and
upper baskets and you can save from both
water and power. This function helps you to
save water and energy
TABLET DETERGENT FUNCTION
Depending on the hardness level of the tap
water, the Tablet Detergent function allows
obtaining a better drying performance from
the multi-purpose detergents such as 2in1,
3in1, 4in1, 5in1, etc., called as all-in-one
detergents. Tablet Detergent Indicator
lights when the Tablet Detergent function is
selected.
Salt and Rinse Aid indicators turn off when
this function is activated.
Turn on your machine by pressing the On/
Off button to use the Tablet Detergent
function. Press the Half Load/Tablet
Detergent button after selecting the desired
programme until Half Load Indicator lights
up, then press Start/Pause/Cancel button
and close the door of your machine.
To use the Half Load and Tablet Detergent
functions concurrently, turn on your
machine by pressing the On/Off button and
then press the Half Load/Tablet Detergent
button until Half Load and Tablet Detergent
Indicators illuminate together.
13
If you have used the Half Load or Tablet
Detergent features during the last
programme you used, Half Load or the
Tablet Detergent function will remain
active in the next washing programme
you will select. If you do not want to use
these functions in the new programme
you have selected, press the Half
Load/Tablet Detergent button until the
indicator of the relevant function turns
off.
START/PAUSE/CANCEL
BUTTON
Reset.
3 sec.
Use this button to start the
selected program. When the
button is pressed once, the light on the
button will turn on.
Stop the program with the Start/Pause/
Cancel button.
REMAING TIME INDICATOR/
DELAY TIME INDICATOR
You can follow the remaining
program duration from the time indicator
display.
TIME DELAY BUTTON
This option enables you to start
the selected program with a
delay of 0,5 to 9,5 hours.
1. Delay time is adjusted by pressing the
Time Delay button (press several times).
2. After adjusting the delay time, press the
Start/Pause/Cancel button.
3. Close the door. At the end of the delay
set, the program starts automatically.
Notice :
During a wash program the Time Delay
option does not function.
USA
CANCELLATION OF A PROGRAM
To cancel a program while the dishwasher
is running:
1. Open the door gently.
2. Press and hold Start/Pause/Cancel
button for 3 seconds. The indicator light will
start flashing.
3. Close the door.
4. The dishwasher will drain the water
inside the machine for 2 minutes. At the
end of the cycle a beep will sound. You can
choose and start a new program.
WARNING
Depending on the stage of the program
you have cancelled, there may be
detergent residue or rinse aid inside
the machine and on the dishes. Make
sure the items in the dishwasher are not
used before washing properly. Ingestion
or inhalation of detergent or rinse aid
may cause serious injury. Avoid contact
with skin and eyes and keep children
and infirm persons away from these
materials.
PROGRAM CHANGE
To change the program selection while the
dishwasher is running:
1. Open the door.
2. Press Start/Pause/Cancel and select a
new program.
3. Press Start/Pause/Cancel again, to start.
WARNING
8 RINSE AID LEVEL INDICATOR LED
Reset.
3 sec.
If this indicator light
comes on, you need
to refill rinse aid.
You can also tell
whether rinse aid
must be refilled by
Dark : Sufficient rinse aid
looking at the rinse
Light : Refill rinse aid
aid dispenser. When
the visual fill indicator
is dark, there is enough rinse aid in the
dispenser.
When the color is light, open the dispenser
and refill rinse aid.
Visual indicator
3 SALT LEVEL INDICATOR LED
(MODEL DEPENDING)
Reset.
3 sec.
When this indicator
light comes on, you
must refill special
salt. Only use special
dishwasher salt in
your machine to
soften the water.
The salt content
can be read on the
container for the salt. When the visual fill
indicator is dark, there is enough salt in the
container.
When the color is light, open the container
and add dishwasher salt.
TU Z
S A LT
14
S EL
SALZ
Depending on the length of the
terminated program detergent and rinse
aid may still be in the dispensers.
Ingestion or inhalation of detergent
or rinse aid may cause serious injury.
Avoid contact with skin and eyes, and
keep children and infirm persons away
from these materials.
USA
If you do not know the hardness of your
water supply, use 15 ml / 3 tsp detergent.
Increase the amount of detergent if you see
white water marks especially on the surface
of the glassware.
Find out the hardness of your water supply
by asking your local water department,
water softener company, or county
extension agent.
7. DETERGENT & RINSE AID
DISPENSER
7.1 FILLING THE DETERGENT
DISPENSER
WARNING
• Always store your detergent in
locations which are cool, dry and out
of the reach of children.
• Check that the detergent dispenser
is empty after the completion of each
wash program.
• Dishwasher detergents can be
dangerous if inhaled or swallowed.
Avoid contact with skin and eyes,
keep children and infirm persons
away from the dishwasher when the
door is opened. Consult a doctor
immediately if detergent has been
swallowed or inhaled.
1. Open the detergent container by pushing
the lock to the right A.
2. Pour / put the detergent into the
dispenser.
3. Close the lid until it clicks in.
Turn the
lock to the
right.
Notice :
• Only use detergents suitable for
dishwashers.
• Do not use detergent in Rinse & Hold
cycle.
• Don’t forget to pour / put the detergent
into the dispenser before turning the
machine on.
• Too much detergent may mean that the
detergent does not dissolve properly
and dishes could get scratched.
• Too much detergent in soft water may
cause glass corrosion. Do not use too
much detergent if your water supply is
soft.
A
• The detergent container holds a total of
40 ml / 8 tsp of detergent 1.
• Marking lines on the inside of the
detergent container aid in providing the
correct amount of detergent. When the
dishwasher is fully loaded and the dishes
are very dirty, we recommend filling the
detergent container up to the 25 ml /
5 tsp mark. When the dishes are less
dirty, it is generally sufficient to fill the
detergent up to the 15 ml / 3 tsp mark.
• The detergent amounts for the individual
cleaning programs are shown in the
“Quick Reference Guide - Program
Table”.
• Fill amounts given are for standard
powder detergent. Amounts may vary if
you use liquid or concentrated powder
detergent. Tablet detergents should be
placed in detergent container 1. With the
cover closed.
• Follow instructions on the package of the
detergent when using liquid dishwasher
detergent, concentrated powder
detergent, or tablet detergent.
DE
TE
RG
EN
T
15
USA
• Deviations are possible depending on
how dirty the dishes are and how hard
the water is in your location.
• If your dishes have been in the
dishwasher for some time without being
washed, also fill the smaller container 2.
up to the top.
DE
TE
RG
EN
Notice :
• Only use rinse aids suited for use in
dishwashers. Rinse aids allow washing
water to rinse off more cleanly and
prevent watermarks or streaks on the
dishes.
• If you use “2 in 1” or “3 in 1”
detergents / tabs, you do not need
additional rinse aid.
T
1
25ml
15ml
25ml = 5 TSP
15ml = 3 TSP
5ml
1. Open the rinse aid dispenser by pressing
the lock B.
2. Carefully pour in rinse aid to the MAX
mark.
3. Close the lid until it clicks in 3.
4. Carefully wipe off spilled rinse aid.
Excessive rinse aid causes excessive
foam formation, which may hinder
cleaning.
2
SET THE DOSE OF RINSE AID
5ml = 1 TSP
TSP = teaspoon
7.2 FILLING RINSE AID DISPENSER
WARNING
Keep your rinse aids out of the reach of
children. Ingestion or inhalation of rinse
aid may cause serious injury. Avoid
contact with skin and eyes, and keep
children and infirm persons away from
rinse aids.
The dose of rinse aid to be used can be
set by means of the dispenser regulator 4
between levels 1 and 6.
Change the setting, only if the following
applies after washing:
• Watermarks are visible on the dishes: Set
dosage higher.
• Streaks are visible on the dishes: Set
dosage lower.
RI
NS
E
AI
D
4
B
16
USA
3
8. SETTING THE WATER SOFTENER (MODEL DEPENDING)
a
b
c
1 Min.
d
e
f
1 Second
1 Minute
Remove the test
strip from the packet.
Turn on the tap and
let the water run for
about a minute.
Hold the test strip in
the water for about a
second.
Remove the test strip
from the water and
shake it.
Wait for 1 minute.
The test strip shows
you the hardness
level.
1. Press the Program Selection button before you switch the appliance on and keep this
button pressed down.
2. Switch the appliance on using the On/Off button; then release the switch.
3. Release the Program Selection button when the water hardness level stored on your
machine is displayed in “r…..” format.
4. Start / Stop icon will start flashing as soon as the water hardness level stored on your
machine.
5. Water hardness can be set to the desired level by pressing the Time Delay button
(compare the test strip with the degrees of Hardness Table). The appropriate program
follows up lights up.
6. Once you have set the hardness level, press the Start/Stop/Cancel button to save the
value. The control indicator on the Start/Stop/Cancel button now lights up permanently.
7. Switch the appliance off again using the On/Off button.
WATER HARDNESS TABLE
Name of unit
American
PPM
German
Definition
1 grain of CaCO3/
1 gal (US) of water
1 mg of CaCO3/
1 L of water
10 mg of CaO/
1 L of water
0-6
0-105
0-5
Press the Time Delay button to switch
the water hardness level to position 1.
7-12
106-210
6-11
Press the Time Delay button to switch
the water hardness level to position 2.
13-18
211-320
12-17
Press the Time Delay button to switch
the water hardness level to position 3.
19-23
321-409
18-22
Press the Time Delay button to switch
the water hardness level to position 4.
24-36
410-624
23-34
Press the Time Delay button to switch
the water hardness level to position 5.
37-47
625-804
35-45
Press the Time Delay button to switch
the water hardness level to position 5.
1st Level
2nd Level
3rd Level
4th Level
5th Level
6th Level
Indicator in the Multi-Function Display
Notice :
• If the water hardness level is less than 7 American degree of hardness, you do not need any
special softening salt. In this case the ‘salt’ control indicator lights up continually.
• If your local hardness level exceeds 47 American degree of hardness, you should consider
getting a water softening device for your dishwasher. If you use stream water or rainwater,
you are advised to install filters.
• If you move do not forget to adjust the water hardness level to suit your new neighborhood.
• If the model does not have a salt dispenser ignore this changes. Water hardness level must
in position 1.
17 USA
9. FILLING THE DISHWASHER
SALT DISPENSER (MODEL
DEPENDING)
CAUTION
Never use culinary or table salt. These
types of salt do not dissolve in water
easily and will damage the function of
the softening device.
Notice :
• Only use special dishwasher salt in your
machine to soften the water.
• Do not use coarse grained salt. Small
grains or powdered salt is more easily
soluble.
• The manufacturer is not liable for
damages resulting from the use of the
wrong type of salt.
D
A
3. When operating for the first time: Pour 1
Liter of water into the salt container (Fig.
C).
4. our the salt into the container with the
aid of the supplied salt funnel (Fig. D).
Pour in enough salt to fill the container.
The container holds approximately 2 kg /
4.4 pounds.
5. Close the cap tightly.
CAUTION
B
Begin any wash program immediately
after filling the salt container. The
washing program prevents damage to
the machine which may be caused by
any spilled salt solution.
After the first washing cycle, the salt
level indicator light will go out. (model
depending)
1. Remove the lower rack from the
machine.
2. pen the screw-in cap of the salt
container by turning it counter
clockwise (Fig. A, B).
18
USA
10. CARE AND MAINTENANCE
WARNING
• Before cleaning or carrying out
maintenance, switch off the appliance,
disconnect the mains plug and turn
off the water tap.
• Do not repair or replace any part of the
dishwasher or attempt any servicing
unless specifically recommended by
this manual. We recommend that the
dishwasher only be repaired by an
authorized service agent.
CAUTION
• To avoid the possibility of slipping,
keep the floor around the dishwasher
clean and dry.
• Keep your appliance free from
the accumulation of combustible
materials, such as lint, rags, and
chemicals.
• If the dishwasher is not in use for
an extended period of time, we
recommend you check that the
baskets are empty, leave the inside
of the dishwasher clean, the door
cracked open to allow air to circulate,
turn off both the power and water
supply to the dishwasher.
Cleaning the colored doors: Use only
soft cloth that is lightly dampened with mild
detergent.
Cleaning the stainless steel doors: Use a
soft cloth with a cleaner made for cleaning
stainless steel. For the best results, apply
the stainless steel cleaner to a soft cloth
and wipe the surface in the direction of the
grain.
Cleaning the door gasket: Regularly
clean the door gasket with a damp cloth to
remove food particles and other debris. Use
a gentle household cleaner for the outside
and the door seals, and rinse throughly.
10.2 CARING FOR YOUR
DISHWASHER INTERIOR
Notice :
Cleaning your dishwasher at regular
intervals ensures longer product life and
reduces the risk of reccurring problems.
Always disconnect the power to machine
before cleaning.
CAUTION
When cleaning the underside of the
main filter, care must be taken on the
sharp outer edge to avoid the risk of cut
type injuries.
10.1 CARING FOR YOUR
DISHWASHER EXTERIOR
10.2.1 CLEANING THE FILTERS
Clean the filters and the spray arms
regularly. A dirty dishwasher will have a
negative effect on the cleaning results.
CAUTION
Possible dishwasher damage: Abrasive
cleaners, scouring pads, abrasive
cloths (paper towels) can damage the
dishwasher decorative door.
The following filters are to be cleaned:
1. Main filter
2. Coarse filter
3. Micro filter
Possible dishwasher damage: Abrasive
cleaners, scouring pads, abrasive cloths
(paper towels) can damage the dishwasher
decorative door.
Cleaning the control panel: Use only soft
cloth that is lightly dampened with mild
detergent. Clean the control panel only with
a moist cloth and clear water.
19
1
USA
10.2.2 CLEANING THE SPRAY ARMS
Notice :
2
3
Dirt and/or calcium residue may block the
nozzles on the spray arms. For this reason,
regularly check the spray nozzles.
1. Lower spray arm
2. Upper spray arm
A
1. Remove the lower rack from the
machine.
2. Turn the coarse filter counterclockwise
to the left and pull it out in an upward
direction A.
3. Pull out the main filter B.
4. Press on the two tabs of the coarse filter
and remove the micro filter C.
5. Clean the filters thoroughly under running
water. Use a brush if necessary.
6. Replace main filter.
7. Replace the micro filter and the coarse
filter into the main filter.
8. Twist it clockwise until it clicks into the
place.
1. Remove the lower rack from the
machine.
2. Pull off the lower spray arm in an upward
direction A.
3. Loosen the fastening screw of the upper
spray arm and pull off the spray arm B by
a downward motion.
4. Clean the spray arms under running
water.
5. Replace the lower spray arm in a
downward direction.
6. Replace the upper spray arm and tighten
the fastening screw by turning it around
to the left.
7. Insert the lower rack.
A
1
B
B
2
C
CAUTION
Ensure that the fastening screw is tight
on upper spray arm.
CAUTION
Do not operate your dishwasher without
a filter. You will damage your machine.
Ensure that your filters are correctly
installed.
20
USA
Check if the holes on the top of the
additional upper spray arm are clogged. If
they are clogged, remove and clean them.
To remove them, slightly 1 push them
upwards and then turn clockwise 2.
To replace the impeller, seat it into its
slot, push slightly upwards and turn it
anticlockwise until it is securely fitted. When
the impeller is released, check if it rotates
without any obstruction.
2
1
21
USA
11. TROUBLE SHOOTING
What if the dishwasher will not run :
• Is the machine plugged in?
• Are all fuses operative?
• Is the water supply fully turned on?
• Is the dishwasher door closed securely?
• Have you pressed the On/Off button?
What if the dishwasher starts but fails to circulate water within 5 seconds :
• Cancel the program by pressing the Start/Pause button for 5 seconds. See section 6. or
Quick Reference Guide.
What if the door will not stay down in open position :
• Adjust door tentioners (wooden door models only, see Installation Manual)
What if the dishwasher produces poor cleaning results :
• “Follow the instructions given in the following pages”
The dishes are not dry
Possible causes
•
Improper loading
How to fix these problems
•
Load the dishwasher as suggested in this
manual.
•
Insufficient rinse aid
supply
•
Increase the dosage amount of rinse aid
and/or refill the rinse aid dispenser.
•
Dishes are removed too
soon
•
Do not empty your dishwasher immediately
after washing. Open the door slightly so
that the steam can escape. Begin with
unloading the dishwasher when the dishes
are only hand warm. Empty the lower rack
first. This prevents water from dripping off
dishes in the upper rack.
•
Wrong program selection
•
In short period programs, the wash
temperature and therefore the cleaning
performance is lower. Choose a program
with a longer washing time.
•
Washing cutlery with
worn surface.
•
Evaporation of water is more difficult with
these items. Cutlery or dishes of this type
is not suited for dishwashers.
22
USA
The dishes are not clean
Possible causes
•
Improper loading.
How to fix these problems
•
Load the dishwasher as suggested in this
manual.
•
Wrong program selection.
•
Select a program that washes at a higher
temperature or takes a longer amount of
time.
•
Spray arms are not
turning.
•
Check if the spray arms are blocked from
moving freely.
•
Clogged filters.
•
Clean all filters as described in this
manual.
•
Filters are not placed in
their proper positions.
•
Check if all filters are placed in their proper
positions.
•
Spray arm nozzles are
clogged.
•
Clean the spray arms as described in this
manual.
•
Overloaded racks.
•
Do not overload the racks.
•
Detergent is moist or
clumping in box.
•
Store detergents in a dry location. Close
the lid of the container securely.
•
Too little detergent.
•
Increase the amount of the detergent as
per the program table.
•
Too little rinse aid.
•
Increase the amount of rinse aid and/or
refill the rinse aid dispenser.
•
The lid of the detergent
dispenser remained open.
•
Always ensure that you close the detergent
dispenser lid after pouring in the detergent.
•
Washing cutlery with worn
surface quality.
•
Cutlery of this type is not suited to
dishwashers.
Tea, coffee or other stains
Possible causes
•
Wrong program selection.
How to fix these problems
•
Select a program that washes at a higher
temperature or takes a longer amount of
time.
23
USA
•
Detergent is moist or
clumping in box.
•
Bleaches in cleaners lose their efficiency
when stored under unfavorable conditions.
Store detergents in a dry location. Close
the lid of the container securely.
•
Using cutlery with a low
surface quality.
•
Cleaning of these items is made difficult
by their poor surface structure. Cutlery or
dishes of this type are not for dishwashers.
Calcium streaks, misty appearance
Possible causes
•
Insufficient rinse aid
supply.
How to fix these problems
•
Increase the dosage amount of rinse aid
and/or refill the rinse aid dispenser.
•
The hardness is not
selected properly; too little
salt is being used.
•
Call water supplier and ask for local
hardness in grains per gallon or ppm. Use
a higher phosphate content detergent for
hard water.
•
Salt loss (models with salt
container)
•
Check whether the lid of the salt container
is firmly closed. Use the funnel to pour
in special salt. Begin the Rinse and Hold
program right after filling in salt. After the
program is complete, check whether the lid
may have loosened.
Smell
Possible causes
•
Smell of new machine.
How to fix these problems
•
The smell of a new machine disappears
after a few wash cycles with detergent.
•
Filters are dirty.
•
Clean all filters as described in this
manual.
•
Dirty dishes standing
in the machine for a
few days without being
washed.
Dirty door gasket.
•
Remove coarse dirt under running water
and run the Rinse and Hold program every
2 days without detergent.
•
Regularly clean the door gasket with a
damp cloth to remove food particles and
other debris. Use a gentle household
cleaner for the outside and the door seals,
and rinse thoroughly.
24
USA
•
Milky appearance or rainbow on the
glasses (glass corrosion)
Possible causes
•
Excessive use of
detergent when water
hardness is low.
How to fix these problems
•
Add a smaller amount of detergent.
•
Compare the water hardness level setting
on the dishwasher against the stated
values from the local water supplier.
•
When water hardness is low (below 7
American degree of hardness or 106 parts
per million), do not use salt even if your
dishwasher has a water softener.
•
Use a lower phosphate content detergent.
Rust stains, destruction of the
surface
Possible causes
•
The lid of the salt
container is not closed
securely. Salt loss.
(models with salt
container)
How to fix these problems
•
Salt can destroy metal surfaces and cause
rust damage.
•
Check whether the lid of the salt container
is firmly closed. Use the funnel to pour
in special salt. Begin the Rinse and Hold
program right after filling in salt. After the
program is complete, check whether the lid
may have loosened.
•
Food leftovers are staying
on the dishes for too long.
•
Remove coarse dirt under running water
and carry out the Rinse and Hold program
every 2 days without detergent.
•
The machine is not
grounded properly.
•
Check the grounding of the system. Static
electricity may eat holes into metal and
cause irreparable damages to surfaces.
•
Cutlery parts from lowgrade rust-free steel.
•
Rust on such items cannot be avoided.
Cutlery or dishes of this type are not suited
for the dishwasher.
•
Dish items with rust
stains.
•
Rusty dishes may “infect“ other items.
Cutlery or dishes of this type are not suited
for the dishwasher.
25
USA
Fading of glasses, china, porcelain
pattern
Possible causes
•
Fading of decoration on
glasses and porcelain.
How to fix these problems
•
Glasses, porcelain and cutlery of this type
are not suited for the dishwasher.
Detergent residue remains in the
dispenser
Possible causes
•
Moisture in the detergent
dispenser.
How to fix these problems
•
Ensure that the detergent dispenser is dry
before filling it.
Detergent stays in
the dispenser of the
dishwasher for too long
The lid of the detergent
dispenser does not open.
•
Pour the detergent in just before washing.
•
When loading the dishwasher, take care
to ensure that you do not accidentally
block detergent cup with large dishware or
utensils.
•
Detergent is moist or
clumping in box.
•
Store detergents in a dry location. Close
the lid of the container carefully.
•
Spray arm nozzles are
clogged.
•
Clean the spray arms as described in this
manual.
•
Spray arms are blocked
by dishware.
Was the cycle terminated
early?
•
Make sure spray arms rotate freely.
•
Terminating the cycle early can leave
detergent residue in the dispenser.
•
•
•
26
USA
Dishes break
Possible causes
•
Improper loading.
•
Overloaded racks.
How to fix these problems
•
Load the dishwasher as suggested in this
manual.
•
Do not overload the dish rack. Dishes may
hit against each other and break.
Scratched dishes
Possible causes
•
Dish items/parts made
from aluminium.
How to fix these problems
•
Dishes and cutlery of this type are not
suited for the dishwasher.
•
The lid of the salt
container is not closed
securely. Salt loss.
(models with salt
container)
•
Check whether the lid of the salt container
is firmly closed. Use the funnel to pour
in special salt. Begin the Rinse and Hold
program right after filling in salt. After the
program is complete, check whether the lid
may have loosened.
•
The hardness is not
selected properly; too little
salt is being used.
•
Call water supplier and ask for local
hardness in grains per gallon or ppm.
Adjust the water hardness level setting
accordingly.
•
Detergents are being
stored under unfavourable
conditions.
•
Detergents should not be stored longer
than 2 months in open packages. Store
detergents in a dry location. Close the lid
of the container carefully.
•
Overloaded racks.
•
Take care to ensure that individual glasses
and dishes do not touch. They may hit
against each other during the washing
process, causing scratches.
27
USA
Foam
Possible causes
•
The dishes are prewashed by hand with
a large amount of dish
detergent.
How to fix these problems
•
Dishes do not need to be pre-washed.
Coarse dirt may be removed with a
dishcloth, or you may hold the dishes
under running water.
•
Rinse aid has accidentally
leaked into the machine.
•
If rinse aid has been spilled during refilling,
remove the aid using a paper cloth or
sponge.
•
The cover of the rinse aid
dispenser is not closed
securely.
•
Always take care to ensure that the
lid is closed after refilling the rinse aid
dispenser.
Water remains inside the machine
after the rinse cycle
Possible causes
•
Clogged filters.
•
How to fix these problems
•
Clean all filters as described in this
manual.
Drain hose kinked or
clogged.
•
Ensure that the drain hose is properly
placed and open.
12. TECHNICAL FEATURES
Load capacity
Permissible water pressure
Electrical connection
Total power
Heater power
12 place settings
4.35 - 145 psi (0.3 - 10 bars)
120 V (volts), 12 A (amps), 60Hz (hertz)
1400 W (watts)
1240 W (watts)
Notice :
Because we continually strive to improve our products, we may change our specifications
and design without prior notice.
This device corresponds to the following directives:
UL 749 Household Dishwasher directive.
28
USA
13. WARRANTY STATEMENT FOR THE BLOMBERG
DISHWASHERS
The warranties provided by Blomberg in
these statements only apply to Blomberg
dishwashers sold to the original purchaser
or homeowner in the US and Canada. The
warranty is not transferable. To obtain
warranty service, please contact our
nearest distributor as listed by state. You
will need your dishwasher model number,
serial number, retailer name and address,
where purchased and purchase date /
installation date. This warranty gives you
specific legal rights, and you may also have
other rights which vary from state to state.
5 year * ++ limited warranty from date of
first installation
(parts only 3-5 years) Blomberg will
repair or replace any circuit boards or
nylon dishwasher racks (excluding any
plastic rack attachments) at no cost
to the consumer if material defects or
workmanship have caused the damage
or failure of these components. The
dishwasher must have been used under
normal household conditions and not
commercially (Labor charges are the
responsibility of the consumer)
“This product is fully tested and went
through official quality assurance
inspections before leaving the original
manufacturing site. Warranty terms for
this Blomberg household appliance is not
valid if the product is altered, tampered,
modifed, additional parts assembled, fixed
and re-packed by an authorized distributor,
servicer, a third party retailer, reseller or by
any other unauthorized person(s)”
Lifetime limited warranty from date of
first installation * ++
(parts only) Blomberg will repair or replace
to the original owner the stainless
steel tub or door if rust through occurs
under normal household use and
normal water conditions (no excessive
chlorine). Blomberg may, at its option,
also replace the whole dishwasher with
the same and/or equivalent model with
equal or better functionality if the original
model is no longer available. (Labor,
removal and installation charges are the
responsibility of the consumer.)
1 year * limited warranty from date of
first installation
Blomberg will repair or replace at no
cost to the consumer any defective parts
of the dishwasher if used under normal
household conditions (warranty is void
if the product is used commercially
e.g., bed + breakfast, nursing home
etc.). Service must also be performed
by an authorized Blomberg service
agency. (Cosmetic defects must be
reported within 10 business days from
installation)
2 year * ++ limited warranty from date of
first installation
(Parts only) Blomberg will repair or replace
any parts at no cost to the consumer if
material defects or workmanship have
caused the damage or failure of these
components. Again the dishwasher
must have been used under normal
household conditions and not
commercially as stated above (Labor
charges are the responsibility of the
consumer).
29
Disclaimers of warranties and
exclusions:
Warranty does not cover service
costs by an authorized service agent
to correct installation, electrical and
plumbing problems or educational
instruction on the use of the
dishwasher. The warranty also does not
cover defects or damage caused by an
act of god (such as storms, floods, fires,
mudslides, steam protection folio etc.),
damage cause by use of the dishwasher
for purposes other than those for
which it was designed, misuse, disuse,
abuse, accident, alteration, improper
installation, maintenance, travel fees,
service calls outside normal service
hours, unauthorized service work.
USA
TO THE EXTENT PERMITTED BY LAW,
THIS WARRANTY IS IN LIEU OF ALL
OTHER EXPRESSED AND IMPLIED
WARRANTIES, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR
PURPOSE. BLOMBERG UNDERTAKES
NO RESPONSIBILITY FOR THE
QUALITY OF THIS PRODUCT EXCEPT
AS OTHERWISE PROVIDED IN THIS
WARRANTY STATEMENT. BLOMBERG
ASSUMES NO RESPONSIBILITY THAT
THE PRODUCT WILL BE FIT FOR ANY
PARTICULAR PURPOSE FOR WHICH
YOU MAY BE BUYING THIS PRODUCT,
EXCEPT AS OTHERWISE PROVIDED IN
THIS WARRANTY STATEMENT.
14. HOW TO GET SERVICE
Please contact the Distributor for your State
or Province as listed on the Distributor
Contact List, or call our Toll Free Number
at 1 800 459 9848 for direction to an
Authorized Blomberg Service Agent.
Blomberg does not assume any
responsibility for incidential or
consequential damages. Such damages
include, but are not limited to, loss of
profits, loss of savings or revenue,
loss of use of the dishwasher or any
associated equipment, cost of capital,
cost of any substitute equipment,
facilities or services, downtime, the
claims of third parties, and injury to
property. Some states do not allow the
exclusion or limitation of incidental or
consequential damages, so the above
limitations or exclusion may not apply to
you.
*
installation date shall refer to either
purchase date or 5 business days
after delivery of the product to the
home, whichever is later.
++ parts replaced will assume the
identity of the original parts + their
original warranty.
No Other Warranties. This Warranty
Statement is the complete and exclusive
warranty from the manufacturer. No
employee of Blomberg or any other party
is authorized to make any warranty in
Statement addition to those made in this
Warranty Statement.
30
USA
17 9042 01 00-AA-USA
Download PDF

advertising