Liebherr | HC1540 | Installation instructions | Liebherr HC1540 Installation Instructions

Installation
Instructions
For Fully Integrated NoFrost
Combined Refrigerator-Freezers
HC 1540/1541
7084 331-00
Important
Please Read and Follow these
Instructions
These instructions contain Danger, Warning and
Caution notes.
This information is important for safe and efficient
installation and operation.
Always read and comply with all Danger, Warning and
Caution notes!
DANGER!
Danger indicates a hazard which
will cause serious injury or death if
precautions are not followed.
WARNING!
Warning indicates a potentially hazardous
situation which, if not avoided, could result
in death or serious injury.
Content
Page
Unit dimensions............................................................. 4
Door swing clearance.................................................... 4
Unit venting.................................................................... 4
Cabinet opening dimensions......................................... 5
Panel dimensions - framed cabinet design................... 6
Panel dimensions - frameless cabinet design.............. 7
Mounting the anti tipping device................................... 8
Cover strips.................................................................... 9
Leveling the appliance................................................. 10
Fastening the appliance in the recess......................... 10
Adjusting the refrigerator door...................................... 11
Adjusting the drawer front............................................. 11
Mounting the ventilation grille...................................... 12
Before mounting the door panels................................ 13
Mounting the attachment brackets
onto the door panels..................................................... 14
Mounting the refrigerator door panel........................... 15
Mounting the freezer drawer panels............................. 17
CAUTION!
Caution indicates a potentially hazardous
situation which, if not avoided, may result
in minor or moderate injury.
IMPORTANT
This indicates information that is especially relevant
to a problem-free installation and operation.
R600a Refrigerant
WARNING!
The refrigerant contained within the
appliance R600a is environmentally
friendly, but flammable. Leaking refrigerant
can ignite.
To prevent possible ignition follow
the warnings below:
Note to the Installer
It is very important to follow the instructions in the
manual to ensure proper installation and operation of
the unit.
• Keep ventilation openings, in
the appliance enclosure or in
the built-in structure, clear of
obstruction.
Before installing the unit, be sure to thoroughly read
and understand all of the information in this manual.
• Do not damage the refrigerant
circuit.
• Any repairs and work on the appliance
should only be performed by the customer
service department.
2
Safety
Disposal of Old Appliance
DANGER!
Risk of child entrapment.
Child entrapment and suffocation are not problems of
the past.
Junked or abandoned refrigerators are still dangerous –
even if they will sit for “just a few days.”
If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.
Before you discard old appliances:
• Remove the doors.
• Leave the shelves in place so that children
may not easily climb inside.
• Cut off the power cable from the discarded
appliance. Discard separately from the appliance.
• Be sure to follow your local requirements for
disposal of appliances.
Contact the trash collection agency in
your area for additional information.
Electrical Safety
Connect this appliance to a 15 amp or 20 amp, 110120 VAC, circuit which is grounded and protected by a
circuit breaker or fuse.
We recommend using a dedicated circuit for this appliance to prevent circuit overload and the chance of
interruption to the appliance.
This appliance is equipped with a three-prong (grounding) polarized plug for your protection against possible
shock hazards.
Where a two-prong wall receptacle is encountered,
contact a qualified electrician and have it replaced with
a properly grounded three-prong receptacle in accordance with all local codes and ordinances.
WARNING!
Electrocution hazard.
Electrical grounding required.
• Do not remove the round grounding
prong from the plug.
• Do not use extension cords or
ungrounded (two prong) adapters.
• Do not use a power cord that is frayed or
damaged.
Disposal of Carton
The packaging is designed to protect the appliance and
individual components during moving and is made of
recyclable materials.
WARNING!
Keep packaging materials away from
children. Polythene sheets and bags can
cause suffocation!
Please recycle packaging material where facilities are
available.
•
Do not use a power strip.
Failure to follow these instructions may
result in fire, electrical shock or death.
Blocking for Safety
WARNING!
To avoid a hazard due to instability of the
appliance, it must be fixed in accordance
with the instructions.
3
Planning Information
Unit Dimensions
- Figure 1, Figure 2
Door Swing Clearance
- Figure 3
Please allow for door
swing clearance at locations next to a wall.
The illustrated measurement is without mounted
front panels. Be sure to
add your panel thickness and handle depth
to this measurement in
order to avoid interferences.
Figure 1
A = 3" (76 mm)
B = 79-13/16" (2027 mm)
C = 29-7/8" (757 mm)
D = 24" (610 mm)
E = 55 1/4" (1413 mm)
F = 37-1/8" (952 mm)
Figure 3
Unit Venting
This type of dimension line indicates the
height measured from
the floor.
- Figure 4
HC appliances do not
require any ventilation
openings in the cabinet.
The required air flow is
directed through the toe
kick area.
Only use the ventilation
grille provided with the
appliance. This grille is
required for proper operation of the appliance.
This opening must not be
covered with a cabinet
base.
Failure to use the supplied grille can result in
product failure and will
void the warranty.
Figure 4
Figure 2
4
Planning Information
Cabinet Opening Dimensions
Cabinet
Height
Inset cabinet
Depth D
- Figure 5
Frameless/faceframe cabinet
Depth D
80"
24" + panel thickness
24"
84"
24" + panel thickness
24"
1
For appliance with panel to be flush,
adjacent cabinetry depth must equal
appliance depth (24") plus panel
thickness (5/8" - 3/4").
1
This is where the power cord extends from the back of
the appliance.
Free length of the power cord = 90 inch (2280 mm)
Be sure to take these specifications into consideration
when choosing the location of the electrical outlet.
IMPORTANT
The electrical outlet must not be situated behind
the appliance and must be easily accessible.
30" Single
60" Side by Side
Figure 5
5
Planning Information
Panel Dimensions - Inset Installation Style
- Figure 6
Side view of cabinet
Cabinet frame
Appliance and panels sit fully within the
opening and are flush with what could
be its own box, between two pantry cabinets or decorative columns, etc. This is
the most common installation scenario.
Door panel
You can order stainless steel panels for inset installation style.
Refrigerator door panel 80"- article number 9900 287-00
Refrigerator door panel 84"- article number 9900 285-00
Freezer drawer panels - article number 9900 283-00
Cabinet opening A
Refrigerator door panel B
80" (2032 mm)
45-1/4" (1150 mm)
84" (2134 mm)
49-1/4" (1251 mm)
The panels should be at least 5/8 inch (16 mm) thick to
allow the connecting rails to be fastened to them.
IMPORTANT
The maximum panel thickness is 3/4" (19 mm).
The door panel weight must not exceed 60 lb
(27 kg).
Figure 6
6
Planning Information
Panel Dimensions - Frameless Installation Style
- Figure 7
Side view of cabinet
With this installation style, these wider
appliance panels partially overlay the
shared side gables of adjacent cabinetry
so as to mimic the look of a frameless
style cabinet.
Cabinet frame
Door panel
Cabinet opening C
Refrigerator door panel D
80" (2032 mm)
45-3/4" (1162 mm)
84" (2134 mm)
49-3/4" (1264 mm)
The panels should be at least 5/8 inch (16 mm) thick to
allow the connecting rails to be fastened to them.
IMPORTANT
The maximum panel thickness is 3/4" (19 mm).
The door panel weight must not exceed 60 lb
(27 kg).
Figure 7
7
Blocking
for
Safety
Mounting the Anti Tipping Device
WARNING!
• The anti tipping bracket must be mounted to
prevent the appliance from tipping when the
fully stocked door is opened.
• Be sure that there is no plumbing or
electrical wiring located in this area which
screws or drills could damage.
- Figures 8 - 11
The anti tipping bracket is provided with the appliance.
1. Mark the center line of the appliance on the back
wall. Align the anti tipping bracket center to this
line.
2. Depending on the constitution of the floor and
wall, use any possible mounting option as shown
in Figures 8 - 11.
IMPORTANT
The anti tipping bracket must be fitted at the same
height as the toe kick area. If you set the appliance
to a higher level by laying spacers underneath, the
anti tipping bracket must be fitted accordingly.
Mounting Options
Mounting the bracket with the wall
stud.
Mounting with wall plugs to concrete
walls (Figure 8).
Mounting with wooden floors (Figure 10).
Screws 6 x 63 mm
Screws 6 x 63 mm
ll
Wa
ll
Wa
or
Flo
Figure 8
Mounting with the wall plate turning in the screws at an angle
(Figure 9).
or
Flo
Figure 10
Mounting with concrete floors using the
anchors provided (Figure 11).
Screws 6 x 63 mm
ll
Wa
ll
Wa
or
Flo
8
or
Flo
Figure 9
Figure 11
Blocking
Cover Strips
Mounting the Anti Tipping Device in Cabinets
deeper than 24" - Figures 12 - 13
A proper function of the anti tipping bracket is warranted
within a cabinet depth of between 24" and 25". If the
cabinet is deeper than 25", a wooden spacer must be
mounted between appliance and wall.
WARNING!
Be sure the wooden spacer is fastened
securely to the floor.
for
Safety
- Figure 14
Apply cover strips above, between and below the securing plates on the side walls of the appliance.
Cut the cover strips to the length shown in Figure 14.
Fit the adhesive cover strips leaving a gap of 1/4" to each
securing plate. This
ensures problem-free
fitting of the covers.
Measuring for mounting the wooden spacer on
inset kitchen cabinets - Figure 12
Depth of spacer depending on clearance between appliance and wall
Figure 14
Panel thickness
Figure 12
Measuring for mounting the wooden spacer on
frameless kitchen cabinets - Figure 13
Move the appliance slowly into the recess until the
appliance back slides into the anti tipping bracket
(Figure 15).
Depth of spacer depending on clearance between appliance and wall
Figure 13
IMPORTANT
If the floor slopes down sideways, the anti tipping
bracket must be fitted horizontally. Lay down
spacers in the appropriate positions.
Figure 15
9
Installation
Leveling the Appliance
- Figure 16
1. Adjust the height of the appliance at the front by
twisting the leveling feet
. Use the open-ended
spanner provided.
Turn the spanner counterclockwise to raise the appliance front and clockwise to lower it. Position the
spanner accordingly (Figure 16 - ).
1
1
Fastening the Appliance in the
Recess - Figure 17
Fasten the appliance in the recess through the premounted securing plates at left and right on the appliance housing using screws 4 x 16 mm. Then click the
covers supplied into place.
2. Adjust the height of the appliance at the rear by turning the adjusting bolts
. Use a 1/4" box spanner or
the Torx 25 wrench provided.
2
3. Rotate leveling feet 1until firmly in place against the
floor.
WARNING!
To prevent the appliance from tipping
(Figure 16)
forward the leveling feet
must have contact with the floor.
1
Figure 17
Figure 16
10
Installation
Adjusting the Refrigerator Door
- Figure 18
Adjusting the Drawer Front
-
Figure 19
IMPORTANT
Under normal conditions, the factory adjustment of
the refrigerator door should not be changed. Only if
heavy loading of the refrigerator door is expected,
may the adjustment be changed.
. Adjust the lateral tilt using the grub
Undo screws
screw
(Allen key A/F 2.5).
1
2
If required, the front of the freezer drawers can be
adjusted.
Transfer the screws shown in the illustration (on the left
and right sides of the freezer drawer) individually to the
long slots below.
Tighten the screws in the front of the drawer once it is
in the right position.
Side view of the freezer drawer
pulled out
Figure 19
Figure 18
11
Installation
Mounting the Ventilation Grille
1. Pull out the bottom freezer drawer.
2. Remove the blue protection film from the dust filter
provided and insert the filter into its opening in the
toe kick area as shown in Figure 20. Engage
the filter at the bottom, press down the
button and click into place.
4. Insert the supports for the ventilation grille on the left
and right sides in the motor compartment
(Figure 22).
Figure 22
Figure 20
3. Remove the locking pins of both supports. The supports are provided with the appliance accessory
pack (Figure 21).
5. The front edge of the
brackets is flush with the
front of the ventilation
grille. Adjust the supports
accordingly (Figure 23).
Figure 23
6. Insert the locking pins to block the
supports (Figure 24).
Figure 21
Figure 24
12
Installation
Before Mounting the Door Panels
- Figures 27, 28
7. Install the ventilation grille (Figure 25).
The grille has bolts on the inside (see detail in
Figure 25 a). These bolts must be inserted into the
holes of the supports.
Remove cover
1 and unscrew the upper and lower
attachment bracket 2 of the refrigerator door. These
brackets will be mounted onto the refrigerator door
panel.
iMPORTANT
The nuts are needed to fit the premounted panel
onto the refrigerator door.
Figure 25
Figure 25 a
8. Adjust the height of the ventilation grille
(Figure 26).
• Loosen the grub screws at the front of the grille
(Allen key A/F 2.5).
• Adjust the ventilation grille to the desired height.
• Tighten the grub screws.
Figure 27
Unscrew the attachment brackets of both freezer drawers. These brackets will be mounted onto the freezer
drawer panels (Figure 28).
iMPORTANT
The screws are needed to fit the premounted
panels onto the freezer drawers.
Figure 26
Figure 28
13
Installation
Mounting the Attachment Brackets onto the Door Panels
- Figure 29
Mark a line with a distance of 41" and 4-1/4" from the bottom of the refrigerator door panel.
Align one of the dismounted brackets of the refrigerator door to the line on the refrigerator door panel as shown in
Figure 29 a. Fasten the bracket with any hole wherever possible using a minimum of 6 screws 4 x 16 mm.
Align the second bracket of the refrigerator door to the bottom line on the refrigerator door panel as shown in
Figure 29 b. Fasten the bracket with any hole wherever possible using a minimum of 6 screws 4 x 16 mm.
Fasten the brackets provided onto the freezer drawer panels using three screws (4 x 16 mm) for each bracket considering the measurement in Figure 29 c.
Figure 29 a
Refrigerator door panel
Figure 29 b
Freezer drawer panel
Figure 29 c
Freezer drawer panel
Figure 29
14
Installation
Mounting the Refrigerator Door Panel
1. Turn in the adjusting bolts on the bottom of the refrigerator door as far as possible (Figure 30).
4. Close the door and check the height of the panel.
5. Align the panel in its vertical position if necessary.
Loosen the hex nuts and turn the adusting bolts
(Figure 32).
Figure 30
Figure 32
2. Open the refrigerator door and hang the panel on the
top adjusting bolts (Figure 31).
6. Align the panel horizontally (with the long holes in
the attachment bracket) (Figure 33).
3. Screw on the hex nuts to the adjusting bolts and finger tighten temporarily (Figure 31).
7. Tighten the hex nuts.
Figure 31
Figure 33
15
Installation
8. Turn the adjusting bolts (bottom refrigerator door)
until they make contact with the attachment bracket
(Figure 34).
10. Loosen the three screws on the top of the attachment bracket, align the panel as shown in
Figure 36 and tighten the screws. This can also be
done with the lower attachment bracket.
Figure 36
Figure 34
9. Screw on the hex nuts and tighten (Figure 35).
11. Click cover
into place.
Insert the cover strip provided
between refrigerator door and panel (Figure 37).
1
2
Figure 35
Figure 37
16
Installation
Mounting the Freezer Drawer
Panels - Figure 38
1. Pull out the upper freezer drawer and screw on the
panel with three screws on the left and right sides
using the screws as shown in Figure 38.
2. Close the drawer and check the position to the surrounding cabinet panels. Align the panel in vertical
direction by loosening the screws left and right.
Finally tighten the screws.
IMPORTANT
Do not overtighten. Do not use a power driver.
3. Pull out the lower freezer drawer and fasten the
lower panel in the same way.
4. Finally cover the gap between the drawer and the
panel of both freezer drawers with the strips provided. Remove the foil from the adhesive surface of
the strip and stick on the top of the appliance drawer
making sure the flexible gasket is fully inserted in the
gap.
3.5 x 13 mm screw
Figure 38
17
For Service in the U.S.
Liebherr Service Center
Toll Free: 1-866-LIEBHER or 1-866-543-2437
Email: Service-appliances.us@liebherr.com
PlusOne Solutions, Inc.
3501 Quadrangle Blvd, Suite 120
Orlando, FL 32817
For Service in Canada
Liebherr Service Center
Toll Free: 1-888-LIEBHER or 1-888-543-2437
www.euro-parts.ca
EURO-PARTS CANADA
39822 Belgrave Road
Belgrave, Ontario, N0G 1E0
Phone: (519) 357-3320
Fax: (519) 357-1326
Download PDF

advertising