Viking | RVCH330SS | Installation Instructions (1 MB) | Viking RVCH330SS Installation Instructions (1 MB)

Installation
Viking Range, LLC
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information, call 1-888-845-4641
or visit the Viking Website at vikingrange.com
Hoods
F21205 EN
(051513)
Table of Contents
IMPORTANT– Please Read and Follow!
Warnings & Important Information _____________________________________________________________________ 3
RVCH Classic Chimney Wall Hoods w/Standard Ventilator
Dimensions & Specifications________________________________________________________________ 5
Clearance Dimensions _____________________________________________________________________ 6
Interior Ventilator Dimensions ______________________________________________________________ 7
Planning Information __________________________________________________________________________ 8
Installation Procedure
Installation (RVCH Classic Chimney Wall Hoods w/Standard Ventilator) __________________________ 9
Duct Cover (RVCH Classic Chimney Wall Hoods w/Standard Ventilator)_________________________ 11
Installation (RVCH Classic Chimney Wall Hoods w/Recirculating Kit) ____________________________ 12
Service & Registration ________________________________________________________________________ 15
NOTE: If installing hood with warming shelf panel,
install warming shelf panel first.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING
1. Installation work and electrical wiring must be
done by qualified person(s) in accordance with
all applicable codes and standards, including
fire-rated construction.
2. Sufficient air is needed for proper combustion
and exhausting of gases through the flute
(chimney) of fuel burning equipment to prevent
back drafting. Follow the heating equipment
manufacturer’s guideline and safety standards
such as those published by the National Fire
Protection Association (NFPA), and the
American Society for Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), and the
local code authorities.
3. When cutting or drilling into wall or ceiling, do
not damage electrical wiring or other hidden
utilities.
4. Ducted fans must always be vented to the
outdoors.
5. WARNING!: To reduce risk of fire, use only
metal ductwork.
6. CAUTION!: To reduce risk of fire and to
properly exhaust air, be sure to duct air outside.
Do not vent exhaust air into spaces within walls
or ceilings, or into attics, crawl spaces, or
garages.
7. CAUTION!: To Reduce the Risk of Fire and
Electric Shock, Install this range hood only with
remote blower models manufactured by Viking,
model numbers – DEV900/DEV1200,
VEV900/VEV1200, OR DEV1500, VEV1500 or
integral blowers manufactured by Viking, model
numbers – DIV300, DIV440, DIV600, DIV800,
DIV1200, VIV300, VIV600, or VIV1200.
NOTE – Please refer inside for specific
canopy/blower combinations.
IMPORTANT – PLEASE READ AND FOLLOW
• Before beginning, please read these instructions
completely and carefully.
• DO NOT remove permanently affixed labels,
warnings, or plates from the product. This may
void the warranty.
• Please observe all local and national codes and
ordinances. If no local codes are applicable, wire
in accordance with the National Electrical Code,
ANSI/NFPA 70-latest edition.
• The installer should leave these instructions with
the consumer who should retain for local
inspector’s use and for future reference.
• Check with a qualified and trained installer or local
codes for makeup air requirement, if any.
This hood is for residential installation only and is
not designed for installation over a commercial
product. Make sure power is off at the main circuit
breaker or fuse box before making connections. To
avoid risk of fire, electric shock, or injury to persons,
turn off the electricity to the hood from the power
supply before servicing or cleaning.
Viking hoods are equipped with the variable speed
controls for blowers. These units will not function
with a single speed ventilator. All Viking ventilator
kits are designed specifically for use with Viking
hoods. Use of any non-Viking ventilator kit will void
the hood warranty.
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF A RANGETOP
GREASE FIRE
1. Never leave surface units unattended at
high setting. Boilovers cause smoking and
greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
2. Always turn hood ON when cooking at
high heat or when cooking flaming foods.
(i.e. crepes suzette, cherries jubilee,
peppercorn beef flambé).
3. Clean ventilating fans frequently. Grease
should not be allowed to accumulate on
fan or filter.
4. Use proper pan size. Always use
cookware appropriate for the size of the
surface element.
2
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING
• Use this unit only in the manner intended by the
manufacturer. If you have any questions, contact
the manufacturer.
• Before servicing or cleaning unit, switch power off
at service panel and lock service panel to prevent
power from being switched on accidentally. When
the service disconnecting means cannot be
locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
3
IMPORTANT– Please Read and Follow!
Dimensions & Specifications
(RVCH Classic Chimney Wall Hoods w/Standard Ventilator)
WARNING
WARNING
”
12 cm)
TO REDUCE THE RISK OF
FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS
Range hoods must be installed
with the ventilators that are
specified on their carton
indicating suitability with this model. Other
ventilators cannot be substituted.
TO REDUCE THE RISK OF INJURY TO
PERSONS IN THE EVENT OF A RANGETOP
GREASE FIRE, OBSERVE THE
FOLLOWING. (Based on “Kitchen Firesafety
Tips,” published by NFPA.)
1. SMOTHER FLAMES with a close fitted lid,
cookie sheet, or metal tray, then turn off the
burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out
immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN. You
may be burned.
3. DO NOT USE WATER, including wet
dishcloths or towels a violent steam
explosion will result.
4. Use an extinguisher ONLY if
• You know it is a Class ABC extinguisher,
and you already know how to operate it.
• The fire is small and contained in the area
where it started.
• The fire department is being called.
• You can fight the fire with your back to an
exit.
0.5
(3
1
(40 6”
.6
cm
)
(5. 2”
1c
m)
(3018”
.5
c
to m)
(7630”
.2
cm
)
1
(30 2”
.5
cm
)
A
”
24 cm)
A (Hood width)
30”W.
29-7/8” (75.9 cm)
36”W.
35-7/8” (91.1 cm)
.0
(61
NOTE: Duct cover included.
RVCH Classic Chimney Wall Hoods w/Standard Ventilator
Description
30”
Duct cover width
Duct cover depth
Duct cover height
Number of lights
Number of filters
Interior ventilator kit
Interior duct size*
Interior—Maximum amps
CAUTION
For general ventilating use only. DO NOT use
to exhaust hazardous or explosive materials
and vapors.
36”
16” (40.6 cm)
12” (30.5 cm)
18” (45.7 cm) to 30” (76.2 cm)
2
2
460 CFM
7” (17.8 cm)
5.6
* Disregard when using recirculating kits.
460 CFM blower is shipped with hood.
NOTE: All products must be hard wired with 2-wire with ground.
4
5
Clearance Dimensions
Interior Ventilator Dimensions
(RVCH Classic Chimney Wall Hoods w/Standard Ventilator)
(RVCH Classic Chimney Wall Hoods w/Standard Ventilator)
Top view
A
16” (40.6 cm)
66
30
(16 ”m
7.6 in.
c
69 to m)
(17 ”ma
5.3 x.
cm
)
(76”mi
.2 n.
c
33 to m)
”
(83 ma
.8 x.
cm
)
A
30”W. 14-15/16” (37.9 cm)
36”W. 17-15/16” (45.6 cm)
4”
(10.2 cm)
9-3/4”
(24.8 cm)
”
36 cm)
(91
.4
120 V
7” (17.8 cm) dia.
duct location
460 CFM Interior Ventilator Installation
6
7
Installation (RVCH Classic Chimney Wall Hoods w/Standard Ventilator)
Planning Information
Plan where the duct work will be located. Install
proper-sized duct work, roof, or wall cap for the
type of blower you are using. Adjust your
measurements for various heights of ceilings,
soffits, cabinets, or ranges/rangetops.
1
Roof cap
7” round duct
2
300 or 600 CFM
single blower
interior-power
typical ductwork
Duct cover or soffit
Proper installation of ducting is extremely
important to ensure maximum performance
from any ventilation product.
• All CFMs are based on tests at 0.1 static pressure:
without applying static pressure, CFM would be
greatly overstated.
• Straight runs and gradual turns are best; for
example, each 90º elbow is equivalent to 5-10 feet
(1.52-3.05 m) of straight run.
• Never use flexible duct; it creates back pressure/air
turbulence and greatly reduces performance.
• Proper performance is dependent on proper
ducting; make sure that a qualified and trained
installer is used.
• Check with a qualified and trained installer or local
codes for makeup air requirement, if any.
• Max. amp rating for hoods includes recommended
ventilator kit rating; all products must be hard
wired direct with 2-wire with ground.
Hood
Roof cap
10” round duct
Duct cover or soffit
Attach transition to damper. Seal with aluminum tape.
Check damper for unrestricted movement,
adjust if necessary.
1200 CFM
single blower
interior power
typical ductwork
WARNING
3
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING
• Use this unit only in the manner intended by
the manufacturer. If you have any questions,
contact the manufacturer.
• Before servicing or cleaning unit, switch
power off at service panel and lock service
panel to prevent power from being switched
on accidentally. When the service
disconnecting means cannot be locked,
securely fasten a prominent warning device,
such as a tag, to the service panel.
Hood
Exterior blower
10” round duct
900, 1200, or
1500 CFM
exterior power
typical ductwork
Duct cover or soffit
Check Framing
Hood
Wall cap
Duct
Wall installation
exterior power
typical ductwork
Duct cover or soffit
Flip hood over and remove electrical box cover.
4
5
1
2
Hood
NOTE: Wall exhaust must be a minimum of 24” (61.0 cm)
from ground. This may vary depending on local codes
and geographic location.
NOTE: Because of the weight of the hood make sure
that the mounting screws are driven into the framing
and not just the drywall. It may be necessary to drill
additional holes in the canopy for proper alignment.
Some hoods require a locally supplied wood strip for
mounting. Check installation procedure of your hood
on page 10 to determine if a wood strip is required.
1
Electrical Supply
Run 120 VAC electrical wiring from service panel
to installation location. See specification pages
for the maximum amp requirements.
Insert 6” of electrical wiring through the
top of vent hood and secure using wiring restrain.
Refer to local codes.
8
Slide duct over transition and tape around joint.
9
11
6
1
5/16”
nut driver
2
CAUTION: If not using a duct cover, using
screws provided make sure top mounting screws are
secured into soffit or cabinet frame. Use additional
mounting screws, if necessary.
CAUTION: Secure vent hood to wall using screws
provided. Use additional mounting screws and
wall anchors, if necessary.
7
3
5/16”
nut driver
8
BARE OR GREEN
Slide filter front over front lip. Push filter rear up,
then slide back over rear lip.
Duct Cover (RVCH Classic Chimney Wall Hoods w/Standard Ventilator)
1
2
1
1
GREEN
BLACK
2
WHITE
BLACK
WHITE
Connect black to black, white to white, and the
green/bare wire under the green screw.
NOTE: Housing wiring must be properly installed for
wiring to be correct when wiring unit.
Replace electrical box cover. Make connection to
breaker box.
Tape to avoid scratching.
3
10
9
Measure distance from ceiling to canopy.
4
1
1
2
3
2
3
2
Slide spacer front over front lip. Push spacer rear up,
then slide back over rear lip.
Slide filter front over front lip. Push filter rear up,
then slide back over rear lip.
10
Place duct cover top inside duct cover base and lower until
desired height is found. Mark height. Use the retaining nuts and
bolts to fasten in place from the inside and remove tape.
Slide duct cover in place and fasten from inside
canopy using the sheet metal screws provided.
11
Installation (RVCH Classic Chimney Wall Hoods w/Recirculating Kit)
1
6
2
7
1
2
5/16”
nut driver
2
Remove damper and discard with transition.
Turn recirculating unit upside down. Place vent hood
upside down on recirculating unit.
8
4
3
Flip hood over. Insert 6” of electrical wiring through
the top of vent hood and secure using wiring restrain.
Refer to local codes.
CAUTION: Secure vent hood. Make sure mounting
screws are secured into framing using additional
mounting screws and wall anchors, if necessary.
9
BARE OR GREEN
1
1
GREEN
BLACK
2
WHITE
WHITE
Attach with screws.
Attach with screws and lock washers provided.
WARNING
5
BLACK
Connect black to black, white to white, and the
green/bare wire under the green screw.
NOTE: Housing wiring must be properly installed for
wiring to be correct when wiring unit.
Replace electrical box cover. Make connection to
breaker box.
11
10
1
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING
• Use this unit only in the manner intended by
the manufacturer. If you have any questions,
contact the manufacturer.
• Before servicing or cleaning unit, switch
power off at service panel and lock service
panel to prevent power from being switched
on accidentally. When the service
disconnecting means cannot be locked,
securely fasten a prominent warning device,
such as a tag, to the service panel.
Remove electrical box cover.
2
3
Assemble brackets to mesh filters and insert
charcoal filters.
12
Slide filter front over front lip. Push filter rear up,
then slide back over rear lip.
13
Service & Registration
13
12
1
1
3
3
Service & Parts
2
2
Slide filter front over front lip. Push filter rear up,
then slide back over rear lip.
Slide spacer front over front lip. Push spacer rear up,
then slide back over rear lip.
Only authorized replacement parts may be
used in performing service on the appliance.
DO NOT repair or replace any part of the
appliance unless specifically recommended in
the manual. All other servicing should be
referred to a qualified technician.
Record the following information indicated
below. You will need it if service is ever required.
The serial number and model number for your
appliance are located on the identification plate
mounted on the inside of the hood canopy.
Model number
_________________________________________
Serial number
_________________________________________
Date of purchase
_________________________________________
Date installed
_________________________________________
Dealer's name
_________________________________________
Address
_________________________________________
14
15
Download PDF

advertising