Frigidaire | FFRE0633U1 | Installation instructions | Frigidaire FFRE0633U1 Installation Instructions

Installation Instructions
READ BEFORE INSTALLING UNIT
BK Window Mounting (5,000 - 6,000 BTU)
INSTALLATION WARNINGS AND CAUTION
Carefully read the installation manual before beginning.
be exposed:
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over an extended
period of time.
NOTE:
Mounting Hardware
Qty.
7
2
(For Wooden windows)
the best way to store unit during winter, or when not
in use.
2
(For Vinyl-Clad windows)
1
5
window sash seal foam
1
insulation panel
Qty.
Top Rail Hardware
weather seals
1
1
2
2
3
4
5
3
6
7
4
8
9
10
5
11
12
ruler
2
1
4
Top Rail
1
Drill (If pilot holes are needed)
Before installing, the top rail must be assembled on the unit.
Top Rail
Fig. B
Fig. C
66129926906
1
Installation
LEFT + RIGHT FILLER PANEL ASSEMBLY
NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear. This is
necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any
reason, this pitch to the rear must be maintained!
Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels - be sure to use the proper
panel for each side. When installed, the flange for securing the panel in place to the window sill will be facing
into the room.
A. Hold the side Panel in one hand and gently pull back the center to free the open end. See FIG. 1.
B. Slide the free end “T” section of the panel directly into the cabinet as shown in FIG. 2. Slide the panel down. Be
sure to leave enough space to slip the top and bottom of the frame into the rails on the cabinet.
C. Once the panel has been installed on the side of the cabinet, make sure it sits securely inside the frame channel by
making slight adjustments. Slide the top and bottom ends of the frame into the top and bottom rails of the cabinet. See
FIG. 3.
D. Slide the panel all the way in and repeat on the other side.
FIG. 1
FIG. 2 “T” section
FIG. 3 Top Rail
Bottom Rail
Cut the seal foam(adherent type) into proper length. Then stick the seal foam at the lower part of the window frame.
Your air conditioner is designed to install in standard double hung windows with opening widths of 22 to 36 inches
(558 mm to 914 mm) (FIG. 4A & FIG. 4B)
Lower sash must open sufficiently to allow a clear vertical opening of 13.25 inches (337 mm ). Side louvers and the rear
of the air conditioner must have clear air space to allow enough airflow through the condenser, for heat removal. The rear
of the unit must be outdoors, not inside a building or garage.
Fig. 4A
SEAL FOAM
Fig. 4B
SEAL FOAM
22" to 36"
(558 mm to 914mm)
22" to 36"
(558 mm to 914mm)
INNER
WINDOW SILL
13.25" min
(337 mm)
13.25" min
(337 mm)
INNER
WINDOW SILL
INTERIOR
WALL
Vinyl-Clad Windows
Wooden Windows
Storm Window:
SASH
If the air conditioner is blocked by Storm Window, add wood as
shown in FIG. 5, or remove storm window before air conditioner
is installed.
If Storm Window Frame must remain, be sure the drain holes or
slots are not caulked or painted shut. Accumulated Rain Water
or Condensation must be allowed to drain out.
2
Storm window
frame or other
obstruction.
1-1/2” min
(38 mm)
FIG. 5
Board
thickness as
required, for
proper pitch to
rear, along
entire sill.
Fasten with
nails or screws.
Installation
Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air
conditioner frame is against the window sill (FIG. 6A & FIG. 6B). Carefully close the window behind the top rail
of the unit.
FIG. 6B
FIG. 6A
INSIDE
OUTSIDE
INSIDE
OUTSIDE
Wooden Windows
Vinyl-Clad Windows
Extend the side panels out against the window frame (FIG. 7A for wooden windows), (FIG. 7B for Vinyl-Clad
windows).
FIG. 7A
FIG. 7B
window
frame
Place the frame lock between the frame extensions and the window sill as shown (FIG. 8A for wooden
windows), (FIG. 8B for Vinyl-Clad windows).
FIG. 8A
Wooden windows:
FIG. 8B
Vinyl-Clad windows:
Drive locking screws:
A: For wooden windows:
NOTE:To prevent
B: For Vinyl-Clad windows:
NOTE:
Before driving the screws, use a drill to drill 5 holes through the holes in the frame lock and frame extensions
3
Installation
Measure the width of the inner side curtain with the provided ruler, as shown (FIG. 10). Mark a line on the
provided insulation panel according to the measured width, then cut out the insulation panel along the line,
as shown (FIG.11). Peel off the protecting film behind the insulation panel and stick the panel on the side
curtain, as shown (FIG.12). Repeat these instructions for the other side.
L
L
2
3
4
5
4
3
2
1
1
6
7
8
9
10
11
FIG. 10
L
FIG. 11
FIG. 12
(FIG. 13).
NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad windows, so you can use lock by
window itself.
9
Cut foam window seal and insert it into the space between the upper and lower sashes (FIG. 14).
FIG. 13
FIG. 14
FOAM SEAL
4
Installation
10
Check that air conditioner is tilted back about 1/4" to 1/2" (tilted about 2º to 4º downward to the outside, see
FIG. 15A & FIG. 15B). After proper installation, condensate should not drain from the overflow drain hole during
normal use, correct the slope otherwise.
FIG. 15A
2º to 4º
FIG. 15B
2º to 4º
H
H
INSIDE
OUTSIDE
INSIDE
OUTSIDE
about 1/4" to 1/2"
Bottom Rail
H
about
1/4" to 1/2"
Wooden Window
11
Bottom Rail
H1
Trim the weather seal
with a proper length,
peel off the protective backing and plug any gaps if needed
as shown FIG.16.
Vinyl-Clad Window
FIG. 16
Removing the air conditioner From Window
Turn the air conditioner off, and disconnect power cord.
Remove sash seal from between windows, and unscrew sash lock.
Remove screws installed through frame and framelock.
Remove the insulation panel and close (slide) side panels into frame.
Keeping a firm grip on air conditioner, raise sash and
carefully remove.
Be careful not to spill any condensate water while lifting
unit from window. Store parts WITH air conditioner.
5
Download PDF

advertising