Klimaire | KSIL036-H215 | User manual | Klimaire KSIL036-H215 User Manual

Klimaire KSIL036-H215 User Manual
Before using your air conditioner , please read
this manua l car efully and kee p it for futur e reference.
INVER TER SPLIT- TYPE
ROOM AIR CONDITIONER
KSIL
USER´S MANUAL
Rea d T hi s Manual
Inside you will find many helpful hints on how
to use and maintain your air conditioner properly.
Just a little preventative care on your part can
save you a great deal of time and money over
the life of your air conditioner. You'll find many
answers to common problems in the chart of
troubleshooting tips. If you review the chart of
Troubleshooting Tips first, you may not need
to call for service.
SOCIABLE REMARK
Sociable remark.......................................................................2
SAFETY PRECAUTIONS
Warning ..............................................................................3
Caution ..............................................................................4
OPERATING INSTRUCTIONS
Parts names ..........................................................................6
Operating temperature.................................................................7
Manual operation .....................................................................7
Airflow direction control ............................................................8
How the air conditioner works ........................................................9
CARE AND MAINTENANCE
Care and maintenance ................................................................10
OPERATION TIPS
Operation tips ......................................................................12
TROUBLESHOOTING TIPS
Troubleshooting tips ................................................................14
C A UT I O N
Contact an authorised service technician for repair or maintenance of this unit.
Contact the authinstaller for installation of this unit.
This appliance is not intended for use by persons(including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Young children should be supervised to ensure that they do not play with the
air conditioner.
If the power cord is to be replaced, replacement work shall be performed by
authorised personnel only.
Installation work must be performed in accordance with the national wiring
standards by authorised personnel only.
SOCIABLE REMARK
When using this air conditioner in the European countries, the following
informations must be followed:
DISPOSAL: Do not. dispose this. product as unsorted municipal waste. Collection
of such waste separately for special treatment is necessary.
It is prohibited to dispose of this appliance in domestic household waste.
For disposal, there are several possibilities:
A) The municipality has established collection systems, where electronic waste can
be disposed of at least free of charge to the user.
B) When buying a new product, the retailer will take back the old product at least
free of charge.
C) The manufacture will take back the old appliance for disposal at least free of
charge to the user.
D) As old products contain valuable resources, they can be sold to scrap metal
dealers.
Wild disposal of waste in forests and landscapes endangers your health when
hazardous substances leak into the ground-water and find their way into the food
chain.
.
SAFETY PRECAUTIONS
To prevent injury to the user or other people and property damage, the following instructions
must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage.
The seriousness is classified by the following indications.
WARNING
This symbol indicates the possibility of death or serious injury.
CAUTION
This symbol indicates the possibility of injury or damage to property.
Meanings of symbols used in this manual are as shown below.
Never do this.
Always do this.
WARNING
Connect with the power
properly.
Do not operate or stop the Do not damag e or use an
unit by switch ing on or o ff unspecified powe r cord.
the power.
Otherw ise, it may cause
It may cause elect ric shockIt may cause electric shock
electr ic shock or fire du e or
to firedue to heat gene ration.
or fire.
excess heat ge ner ati on.
Do not operate with wet
hands or in damp
environment.
Do not direct airflow at
room occupants only.
It may cause electric shock.
This could damage your
health.
Always ensure effective
earthing.
Do not allow water to run
into electric parts.
Always install circuit
breaker and a dedicated
power circuit.
No earthing may cause
electric shock.
It may cause failure of
machine or electric shock.
No installation may cause
fire and electric shock.
Disconnect the power if
strange sounds, smell, or
smoke comes from it.
Do not drink water drained
from air conditioner.
Do not open the unit
during operation.
Do not modif y power cord
lengt h or shar e the outlet
with other appliances
It may cause electric shock
or fire due to heat generation.
It may cause fire and
electric shock.
Use the correctly rated
breaker or fuse.
There is risk of fire or
electric shock.
It contains contaminants and
could make you sick.
It may cause electric shock.
Do not use the power cord
close to heating appliances.
Do not disassemble or
modify unit.
It may cause fire and
electric shock.
It may cause failure and
electric shock.
Ventilate room before operating air
conditioner if there is a gas leakage
from another appliance.
It may cause explosion, fire and, burns.
Do not use the power cord near
flammable gas or combustibles, such
as gasoline, benzene, thinner, etc.
It may cause an explosion or fire.
SAFETY PRECAUTIONS
CAUTION
When the air filter is to be
removed, do not touch the
metal parts of the unit.
Do not clean the air
conditioner with water.
Ventilate the room well
when used together
with a stove, etc.
It may cause an injury.
Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
An oxygen shortage
may occur.
When the unit is to be
cleaned, switch off, and turn
off the circuit breaker.
Do not put a pet or house
plant where it will be
exposed to direct air flow.
Do not use for
special purposes.
Do not clean unit when
power is on as it may cause
fire and electric shock, it may
cause an injury.
This could injure the pet or
plant.
Do not us e thi s air co nditione r to pre ser ve pr ecision devi ces, foo d, pe ts,
plants , and ar t obje ct s.
It may ca use dete rio ra tion
of qua lit y, et c.
Stop operation and close
the window in storm or
hurricane.
Do not place obstacles
around air-inlets or inside
of air-outlet.
Turn off th e main power
switch wh en no tu sing
the un it fo r a lo ng ti me.
Operation with windows
opened may cause wetting
of indoor and soaking of
household furniture.
It may cause failure of
appliance or accident.
It may cause failure of
product or fire.
Do not use strong detergent
such as wax or thinner. Use
a soft cloth for cleaning.
Ensure that the installation bracket of
the outdoor appliance is not damaged
due to prolonged exposure.
Appearance may be
deteriorated due to change
of product color or
scratching of its surface.
If bracket is damaged, there
is concern of damage due to
falling of unit.
Operation without filters
may cause failure.
Do not place heavy object on the
power cord and take care so that
the cord is not compressed.
Use caution when unpacking
and installing. Sharp edges
could cause injury.
If water enters the
unit, turn the unit off
and disconnect the
power , contact a
qualified service
technician.
There is danger of fire or
electric shock.
n Always insert the filters ters
securely. Clean filter
once every two weeks.
OPERATING IN STRUCTIONS
Parts names
Indoor unit
N o te : T h e i n d o o r u ni t y o u p u rc h a se d m a y l o ok
l i ke o n e o f t h e f ol l o wi n g :
Air inlet
1
5
6
2
Indoor unit
3
4
Air outlet
7
10
8
9
11
12
13
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Signal receptor
Display panel
Panel frame
Chassis
Front panel
Horizontal louver
Vertical louver(on some models)
Air filter(under the panel)
Manual control button
Remote controller holder
Remote controller
Connecting pipe
Drain hose
(A)
Outdoor unit
14. Connecting cable
15. Connective pipe
16. Stop valve
(B)
NOTE:
All the pictures in this manual
are for explanation purpose
only. Your air conditioner may
be slightly different.
The actual shape shall prevail.
Outdoor unit
Air inlet(rear)
Air inlet(side)
Air outlet
14
15
16
OPERATING INSTRUCTIONS
LED display panel
T h e di s p la y p a n el of th e a i r c o nd i t io n e r y ou
p u rc h a se d w o ul d l o o k l ik e o n e o f t h e f ol l o wi n g :
TIMER indica tor
This indicat or illuminates when
TIMER progra m is set ON/OFF.
Signal
receptor
(1)
AUTO indicat or
This indicat or illuminates when
the air cond itioner is in AUTO
operation.
OPERATION FREQ UENCY indicator
This display is separated into five zones.
The zones il luminate based on the
compressor c urrent operation. For
example: hig h frequency will illuminate
more zones.
Signal
receptor
(2)
Signal
receptor
Signal
receptor
(3)
TEMPERATURE indicator
A) Usually it displays the temperature
settings. W hen change the setting
temperature,th is indicator begins
to flash, a nd stops 20 seconds later.
B) It displays the room temperature
when the ai r conditioner is in FAN
only operatio n.
C) Displays th e malfunction code or
protectio n code.
DEFROST indi cator
(For Cooling & Heating models only)
This indicat or illuminates when the
air conditio ner starts defrosting
automaticall y or when the warm air
control feat ure is activated in heating
operation.
(4)
CLEAN AIR indi cation lamp:
Lights up whe n CLEAN AIR feature
is activated.
OPERATING INSTRUCTIONS
N O TE : T h is ma n u al do e s n o t i nc l u de Re m o te Co n t ro l l er Op e r at i o ns , s e e t h e
< < Re m o te C o n tr o l le r I n s tr u c ti o n >> pa c k ed wi t h t h e u ni t f o r d e ta i l s.
Operating temperature
Mode
Temperature
Room temperature
Outdoor temperature
CAUTION:
1. If air conditioner is used outside of the above conditions, certain safety protection
features may come into operation and cause the unit to function abnormally.
2. Room relative humidity less than 80%. If the air conditioner operates in excess of
this figure, the surface of the air conditioner may attract condensation. Please sets the
vertical air flow louver to its maximum angle (vertically to the floor), and set HIGH fan
mode.
3. Optimum performance will be achieved within these operating temperature.
Suggestion: For the unit adopts an Electric Heater, when the outside ambient
O
O
temperature is below 0 C(32 F), we strongly recommend you to keep the machine
plugged in order to guarantee it running smoothly.
Manual operation
Manul operation can be used temporarily in case the remote controller is disable or
maintenance necessary.
Front panel
Manual control
button
AUTO/COOL
N O TE : T h e u ni t m u s t b e t ur n e d o ff be f o re
o p er a t in g t h e m an u a l c on t r ol bu t t on . I f t h e
u n it i s o p e ra t i on a l , c on t i nu e p r e ss i n g t he
m a nu a l c on t r ol bu t t on un t i l t he un i t i s o f f.
1 Open and lift the front panel up to an angle
until it remains fixed w ith a clicki ng sou nd.
2 One press of the manual control button will
lead to the forced AUTO operation. If press
the button twice within five seconds, the unit
will operate under forced COOL operation.
Close the panel firmly to its original
3
position.
●
●
CAUTION:
This button is used for testing purposes
only. You had better not choose it.
To restore the remote controller operation,
use the remote controller directly.
OPERATING INSTRUCTIONS
Airflow direction control
Adjust the air flow direction properly otherwise, it
might cause discomfort or cause uneven room
temperatures.
Adjust the horizontal louver using the remote
controller.
Adjust the vertical louver manually.
To set the vertical air flow(Up--Down) direction
Perform this function while the unit is in operation.
Use the remote controller to adjust the air flow
direction. The horizontal louver can be moved at
O
a range of 6 for each press, or swing up and down
automatically. Please refer to the
REMOTE
CONTROLLER OPERATION MANUAL
for details.
Range
Vertical
louver
(three places)
To set the horizontal air flow direction (left - right)
Move the vertical louver manually to adjust the air flow
in the direction you prefer.
IMPORTANT: Before adjusting the vertical louvers, the
supply power must be disconnected.
For some models, the vertical louver can be adjusted
by using the remote controller. Please refer to the
REMOTE CONTROLLER OPERATION MANUAL
for details.
CAUTION
Range
Do not operate the air conditioner for long periods with
the air flow direction set downward in cooling or
dehumidifying mode. Otherwise, condensation may
occur on the surface of the horizontal louver causing
moisture to drop on to the floor or on furnishings.
Do not move the horizontal louver manually unless it is
necessary. Always use the remote controller.
When the air conditioner is started immediately after it
was stopped, the horizontal louver might not move for
approximately 10 seconds.
Open angle of the horizontal louver should not be set
too small, as COOLING or HEATING performance may
be impaired due to too restricted air flow area.
Do not operate unit with horizontal louver in closed
position.
When the air conditioner is connected to power (initial
power), the horizontal louver may generate a sound for
10 seconds, this is a normal operation.
OPERATING INSTRUCTIONS
How the air conditioner works
SLEEP
operation
7 hours tim e r off
Set
Temperature
1 hour
1 hour
Cooling
SLEEP
operation
7 hou rs ti m er o ff
Set
Temperature
1 hour 1 h our
Heatin g
AUTO operation
When you set the air conditioner in AUTO mode, it will
automatically select cooling, heating(cooling/heating
models only), or fan only operation depending on what
temperature you have selected and the room
temperature.
The air conditioner will control room temperature
automatically round the temperature point set by you.
If the AUTO mode is uncomfortable, you can select
desired conditions manually.
SLEEP operation
When you push SLEEP button on remote controller
during cooling, heating(cooling & heating models only),
or AUTO operation , the air conditioner will
automatically increase (cooling) or decrease (heating)
per hour for the first 2 hours, then hold
steady for the next 5 hours, after that it will switch off.
This characteristic maintains both enery saving and
comfort in night operation.
DRYING operation
The fan speed will be automatically controlled under
dry operation.
During the dry operation, if the room temperature is
lower than 10OC(50OF), the compressor stops operation
and restarts until the room temperature is above
12OC(54OF).
Optimal operation
To achieve optimal performance, please note the
following:
Adjust the air flow direction correctly so that it is not
directed on people.
Adjust the temperature to achieve the highest comfort
level. Do not adjust the unit to excessive temperature
levels.
Close doors and windows on COOL or HEAT modes,
or performance may be reduced.
Use TIMER ON button on the remote controller to
select a time you want to start your air conditioner.
Do not put any object near air inlet or air outlet, as the
efficiency of the air conditioner may be reduced and
the air conditioner may stop running.
Clean the air filter periodically, otherwise cooling or
heating performance may be reduced.
Do not operate unit with horizontal louvre in closed
position.
CARE AND MAINTENANCE
Care and maintenance
Cleaning the Grille, Case and Remote Controller
Turn the system off before cleaning. To clean, wipe with
a soft, dry cloth. Do not use bleach or abrasives.
NOTE: Supply power must be disconnectd before
cleaning the indoor unit.
CAUTIONS
Filter Handle
A cloth dampened with cold water may be used
on the indoor unit if it is very dirty. Then wipe it
with a dry cloth.
Do not use a chemically treated cloth or duster to
clean the unit.
Do not use benzine, thinner, polishing powder, or
similar solvents for cleaning. These may cause
the plastic surface to crack or deform.
Never use water hotter than 40OC/104OF to clean
the front panel, it could cause deformation of
discoloration.
Cleaning the air filter
A clogged air filter reduces the cooling efficiency of
this unit. Please clean the filter once every 2 weeks.
1. Lift the indoor unit panel up to an angle until it
stops with a clicking sound.
2. Take hold of the handle of the air filter and lift it
up slightly to take it out from the filter holder,
then pull it downwards.
3. Remove the AIR FILTER from the indoor unit.
Clean the AIR FILTER once two weeks.
Clean the AIR FILTER with a vacuum cleaner
or water, then dry it up in cool place.
.
.
CARE AND MAINTENANCE
4. Remove the Air Freshening Filter from its support
frame (on some models).
(The optional filter include :Plasma Dust Collector/
Silver Ion filter /Bio filter /Vitamin C filter/3M air
purifier filter, etc. The removing and installation
methods are slightly different, see the pictures
marked 1
and 2
on the left.
Clean the air freshening filter at least once a
month ,and re lpace it ever y4-5 months.
Clean it with vacuum cleaner, then dry it in cool
place.
.
.
1
Do not touch the Plasma Dust Collector
Filter within 10 minutes after opening the
front panel, it may cause an electric shock.
5. Install the air freshening filter back into position.
6. Insert the upper portion of air filter back into the
unit, taking care that the left and right edges line
up correctly and place filter into position.
Maintenance
2
If you plan to idle the unit for a long time, perform
the following:
(1) Operate the fan for about half a day to dry the
inside of the unit.
(2) Stop the air conditioner and disconnect power.
Remove the batteries from the remote controller.
(3) The outdoor unit requires periodic maintenance
and cleaning. Do not attempt to do this yourself.
Contact your dealer or servicer.
Checks before operation
Check that the wiring is not broken off or
disconnected.
Check that the air filter is installed.
Check if the air outlet or inlet is blocked after the
air conditioner has not been used for a long time.
C a ut i o n
Do not touch the metal parts of the unit when
removing the filter. Injuries can occur when
handling sharp metal edges.
Do not use water to clean inside the air conditioner.
Exposure to water can destroy the insulation,
leading to possible electric shock.
When cleaning the unit, first make sure that the
power and circuit breaker are turned off.
OPERATION TIPS
The following events may occur during normal operation.
1. Protection of the air conditioner.
Compressor protection
The compressor can't restart for 3 minutes after it stops.
Anti-cold air (Cooling and heating models only)
The unit is designed not to blow cold air on HEAT mode, when the indoor heat exchanger is in
one of the following three situations and the set temperature has not been reached.
A) When heating has just starting.
B) Defrosting.
C) Low temperature heating.
The indoor or outdoor fan stop running when defrosting (Cooling and heating models only).
Defrosting (Cooling and heating models only)
Frost may be generated on the outdoor unit during heat cycle when outdoor temperature is low
and humidity is high resulting in lower heating efficiency of the air conditioner.
During this condition air conditioner will stop heating operation and start defrosting automatically.
The time to defrost may vary from 4 to 10 minutes according to the outdoor temperature and
the amount of frost build up on the outdoor unit.
2. A white mist coming out from the indoor unit
A white mist may generate due to a large temperature difference between air inlet and air outlet
on COOL mode in an indoor environment that has a high relative humidity.
A white mist may generate due to moisture generated from defrosting process when the air
conditioner restarts in HEAT mode operation after defrosting.
3. Low noise of the air conditioner
You may hear a low hissing sound when the compressor is running or has just stopped running.
This sound is the sound of the refrigerant flowing or coming to a stop.
You can also hear a low "squeak" sound when the compressor is running or has just stopped
running. This is caused by heat expansion and cold contraction of the plastic parts in the unit
when the temperature is changing.
A noise may be heard due to louver restoring to its original position when power is first turned on.
4. Dust is blown out from the indoor unit.
This is a normal condition when the air conditioner has not been used for a long time or during first
use of the unit.
5. A peculiar smell comes out from the indoor unit.
This is caused by the indoor unit giving off smells permeated from building material, from furniture,
or smoke.
6. The air conditioner turns to FAN only mode from COOL or HEAT (For cooling and
heating models only) mode.
When indoor temperature reaches the temperature setting on air conditioner, the compressor will
stop automatically, and the air conditioner turns to FAN only mode. The compressor will start again
when the indoor temperature rises on COOL mode or falls on HEAT mode (For cooling and heating
models only) to the set point.
OPERATION TIPS
7. Dripping water may generate on the surface of the indoor unit when cooling in a high
relatively humidity (relative humidity higher than 80%). Adjust the horizontal louver to
the maximum air outlet position and select HIGH fan speed.
8. Heating mode (For cooling and heating models only)
The air conditioner draws in heat from the outdoor unit and releases it via the indoor unit
during heating operation. When the outdoor temperature falls, heat drawn in by the air
conditioner decreases accordingly. At the same time, heat loading of the air conditioner
increases due to larger difference between indoor and outdoor temperature. If a
comfortable temperature can't be achieved by the air conditioner, we suggest you use a
supplementary heating device.
9. Auto-restart function
Power failure during operation will stop the unit completely.
For the unit without Auto-restart feature, when the power restores, the OPERATION indicator
on the indoor unit starts flashing. To restart the operation, push the ON/OFF button on the
remote controller. For the unit with Auto-restart feature, when the power restores, the unit
restarts automatically with all the previous settings preserved by the memory function.
For some models, the machine is special designed with Auto-restart function for the open angle
of the horizontal louver.Power failure during operation or pressing the ON/OFF button on the
remote controller will stop the unit completely.When the power restores or pressing the ON/OFF
button on the remote controller again,the unit restarts automatically with all the previous settings
including the open angle of the horizontal louver by the memory function.So we strongly suggest
that the open angle of the horizontal louver should not be set too small,in case the condensed
water forms and drops from the horizontal louver. Press the AUTO/COOL button under the
front panel and the open angle of the horizontal louver will be restored to the standard angle
when the condensed water forms on the horizontal louver.
10. Lightning or a car wireless telephone operating nearby may cause the unit to malfunction.
Disconnect the unit with power and then re-connect the unit with power again. Push the
ON/OFF button on the remote controller to restart operation.
TROUBLESHOOTING TIPS
Troubleshooting Tips
Stop the air conditioner immediately if one of the fol lowing faults occur. Disconnect the
power and cont act the nearest customer service cent er.
If the following code appea rs on the LED windo w, disco nnect the power and contact
the service peop le: E0,E1, E2,E3,E4 ,E5,E6,E7,E 8 or P0,P1,P2,P3,P4 ,P5, P6.
Trouble
Fus e blows frequently or circu it breake r trips freq uently.
Other objects or water penetrate the air conditioner.
The remote con troller won 't work or works abnormally.
O p erat on ind ic at or o r oth e r i nd ic ator s f las h ra pi d l y a nd thi s fl as h ca n no t be
s t oppe d by disc onnectin g t he po we r an d th e n co nn ec tin g i t i n ag ai n.
Malfunctions
Unit does not
start
Cause
Power cut
What should be done?
Wait for pow er to be restore d.
Unit may have become unpl ugged. Check that plug is securely in wall
receptacle.
Fuse may hav e blo wn.
Replace the fu se.
Batt ery in Remote control ler may Repl ac e the battery.
have been exhausted.
The time you have set with tim er Wait or cancel timer sett ing.
is inc orrect.
Unit not cooling
or heating
(Coolin g/ heating
models only)
room very well
while air flowing
out from the air
condi tioner
Inapp ropriate temperature
Set tempe rature corr ec tly . For
setti ng.
deta iled method plea se re fer to
" Usi ng re mote contro
"l
se ction.
Air filter is blocked.
Clean the air filter.
Door s or Windows are open.
Close the door s or windows.
Air inlet or out let of indoor or Clear obstructions away first, then
outdoor unit has bee n block ed.
restart the unit.
Compr essor 3 or 4 minutes
protecti on has been activat ed.
Wait.
If the trouble has not been corrected, please contact a local dealer or the nearest customer
service center. Be sure to inform them of the detailed malfunctions and unit model.
Notes: Do not attempt to repair the unit yourself.
Always consult an authorised service provider.
7909 N.W. 54th Street, Miami, FL 33166 USA
Tel: (305)594-4972 Fax (305) 675-2212
www.klimaire.com
sales@klimaire.com
The design and specifications are subject to change without prior notice for
product improvement. Consult with the sales agency or manufacturer for details.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising