Amana | PTH123G35CXXX | Master Catalog | Amana PTH123G35CXXX Master Catalog

Amana PTH123G35CXXX Master Catalog
PACKAGE TERMINAL AIR CONDITIONER (PTAC)
AND HEAT PUMP
Specifications and Accessories Catalog
Wise Decision.
It’s an Amana® brand.
Amana is a registered trademark of Maytag Corporation or
its related companies and is used under license to Goodman
Company, L.P., Houston, TX, USA. All rights reserved.
Premium Amana®
Brand Quality
Featuring
DigiSmart ®
Web-Based
Monitoring
DIGISMART®
A Combination of Energy Management and PTAC Performance
Amana® brand DigiSmart® brings together our best PTAC with our best energy management software that now integrates
with optional property management and front desk management software. Reduce PTAC energy consumption up to
35% OR MORE* through the power of the in-unit energy management system, programmable temperature set-back, and
temperature limiting combined. Our Maintenance Notification System can alert when there is a potential maintenance
issue with the PTAC.
Amana brand DigiSmart Solution
In - Ro om "Self- Installable" Wireles s Peripherals
The DigiSmart Wireless Remote
Thermostat can be mounted on the
wall anywhere in the guest room. It is
Battery powered and with its own wireless ability to communicate with the
PTAC to maintain room temperature.
Best of all, there are no wires to run. The PTAC and thermostat
connect at the press of a button and work in-sync to display
accurate temperature.
The DigiSmart Occupancy Sensor
and Door Switch Combo Device
completes the in-room equipment.
This infrared sensor can determine
whether the room is occupied or
empty and when empty, signal the PTAC to adjust the temperature to save energy based on programmable set-backs.
The DigiSmart Wireless Antenna
installs inside the PTAC with a snap-in
connector like a telephone jack. Installing the antenna allows the PTAC
to communicate wirelessly with other
devices in the room and to the DigiSmart network.
■■
60,000+ rooms have had wireless installations
since 2005
■■
Total wireless devices deployed to date: 425,000+
The Amana brand DigiSmart PTAC with antenna, combined
with the self-installable, wireless thermostat and occupancy
sensor give the property owner complete control over the
equipment settings and can reduce PTAC energy usage up
to 35% OR MORE.*
Site-Level — Central Wireless Controller
■■
Site-wide PTAC Configuration
■■
Site-wide PTAC Diagnostics
■■
Front-Desk System Interface
■■
Email Reporting
■■
Internet Accessible Web User Interface Enterprise
DigiSmart
Controller
* These savings represent estimated savings over time and were generated using general
assumptions including energy loads, local weather averages and use of occupancy controls.
Actual savings will vary according to actual use habits, room square footage, and how the
unit is installed and maintained.
www.amana-ptac.com
Data Warehouse Site Managment
Ent
Maintenance Staff
Internet
DigiSmart
Controller
Site #1
r
se o
ess
Acc
Enterprise
DigiSmart
Controller
Enterprise – Multiple Wireless Controllers
Owner
orm
Central Monitoring and Control of Multiple Properties
or
Platform
Access
Sig
na
l
l
na
Sig
Front Desk Staff
ri
erp
Platf
General Managers
DigiSmart
Controller
Site #2
■■
Data Warehousing
■■
Load Shedding
■■
Virtual Metering
■■
Email Reporting
■■
Savings Analysis
Site #3
Web-Based Monitoring –
Amana® brand DigiSmart® Controller
All PTACs in a building can be managed
through a single interface on a PC.
Features Include:
■■
Full unit details for every PTAC, visible from the front
desk or home office
■■
Automatic emails for PTAC maintenance
■■
Ability to change all settings on the unit
■■
Enhanced diagnostics
■■
Monitors up to 170 PTACs WIRELESSLY with
one controller
■■
Expand the network with additional controllers
–– System Verification – Site Statistics
–– Global Setbacks
– Email Reporting
–– EMS Configuration
– Unit Health
–– Site Statistics
– Unit Code Alerts
Unrented Set-Points
By integrating with your property’s Front Desk System,
the PTACs will adjust to specific set-points when no longer
identified as rented in the system.
Temp Limiting
Each PTAC can be configured with a heating and cooling
temperature set-point limit.
Set-backs
Once a room is declared unoccupied by the occupancy
sensor, the PTAC progresses through three different temperature set-backs, configured as three degree and time
pairs (An example configuration is listed below).
1. 2°, 30 mins – Setback the temp 2 degrees
after 30 minutes
2. 4°, 1 hr – Setback the temp 2 more degrees
after 30 more minutes
3. 8°, 3 hrs – Setback the temp 4 more degrees
after 2 more hours
Talk to your Amana brand dealer about opportunities to optimize the efficiency
of your new unit. Before purchasing this appliance, read important information
about its estimated annual energy consumption, yearly operating cost or energy
efficiency rating that is available from your dealer.
www.amana-ptac.com
3
Standard Features
■■
■■
Energy Efficiencies: With EERs up to 12.0 and COPs
up to 3.4, our unit’s high efficiencies may qualify
you for many of the rebates offered by electrical
power companies.
Quiet Operation: Our PTAC has been redesigned to be
the quietest PTAC we’ve ever built. The unit’s stateof-the-art design and construction provide a quiet
environment, allowing guests to enjoy peaceful,
sleep-filled nights.
■■
■■
■■
–– Two fan motors (indoor/outdoor)
–– Indoor tangential fan for quiet operation
–– STC of 28
■■
■■
■■
■■
■■
4
Assembled in the USA for 35 years: assembled at our
plant in Fayetteville, TN, using Goodman resources
including engineering, production, and testing.
■■
Increased Dehumidification Capacity: Maintain lower
humidity levels in rooms while cooling them without
the need for expensive add-ons. As a result, guests feel
more comfortable at higher temperatures, thus
reducing cooling costs.
Seven-Button Touch Pad: Provides complete control
to guests for in-room comfort while maintaining
energy efficiency.
Five-Year Limited Warranty: Enjoy one of the most
comprehensive warranties in the industry: First Year:
parts & labor; Second through fifth years: parts
& labor on certain sealed system components;
second through fifth years: on certain functional
parts only. For complete warranty details, visit
www.amana-ptac.com.
100% Run Tested: All units are 100% run tested at
our plant in Fayetteville, TN, including leak checks
during manufacturing and again prior to shipment
at the warehouse.
www.amana-ptac.com
■■
7⅝" Unit Front Depth: Enhance valuable room
space with our slim unit front, which has a sleek
7⅝" depth, one of the shallowest silhouettes in
the industry today. In addition, to inhibit guesttampering, the front can be secured to the chassis
with a hidden screw.
Easy Pull-Out Filters: Our filters are washable and
easy to maintain.
Filter Dryer for Sealed System Refrigerant: Standard
in all units to protect the compressor and lengthen the
life of the unit by removing moisture and preventing
acid formation.
Condensate Dispersion System: Our condensate
dispersion system removes condensate from indoor
cooling operation by throwing water directly on to
the outdoor coil for rapid evaporation and increased
cooling efficiencies. The slinger ring on the new,
enhanced fan draws water up and into the fan blades.
This water is then atomized and evaporated into the
atmosphere through the condenser. Increased surface
area from the coil allows more water to be evaporated
on the sides of the coils and helps to minimize
condensate run-off.
Front Desk Control: Each unit comes equipped with
the DigiSmart™ control and energy management
software. Using the DigiSmart™ software and optional
RF Antenna, all units can be wirelessly connected
to a central hub for enhanced energy savings and
diagnostics. Amana brand PTACs also have a lowvoltage interface capability with a field-supplied
front-desk ON/OFF switch. (See inside front cover.)
■■
■■
■■
■■
■■
■■
■■
Room Freeze Protection: When the unit senses
temperatures of 40°F or below, the unit activates
the fan motor and either the electric resistance
heater or the hydronic heater.
Easy-to-use Controls: No complex controls to confuse
your guests and create phone calls for your manager.
Controls are easy to read, understand, and activate.
Our new 7-button control panel provides guests with
complete control of the unit for their in-room comfort
while maintaining overall energy efficiency.
Easy to Service with On-Board LED Diagnostics:
The main components are easily serviced and there
is no guessing to determine the problem with our
easy-to-read diagnostics.
Stonewood Room Front: Our Stonewood room front
strikes the balance between attractive styling and
practical design. Distinctive contours and a modern
appearance enhance the character of even the most
luxurious room, while the sleek 7⅝" depth maximizes
usable space for your guests.
Remote Thermostat Control: When the DigiSmart™
wireless remote thermostat (DS01E, sold separately) is
set up, both the remote thermostat and unit control
panel continue to control the unit, providing flexibility
and home-like system control. Installation requires no
more than pressing two buttons. No need to run wires
or make electrical connections.
Extended Heat Pump Heating: Heat pump models
will operate in the heating mode down to as low as
24°F outdoor ambient temperature.
Zero Floor Clearance: The unit can be installed flush
to a finished floor, if desired. (Some accessories do
not have zero clearance).
■■
■■
■■
■■
■■
■■
30-Second Fan-Off Delay: The fan continues to run
30 seconds after the compressor has stopped in either
cooling or heat pump mode and after electric heat has
been turned off. This improves efficiency by dispersing
the conditioned air on the coils into the room.
Compressor Lock-In: This feature helps prolong the life
of the compressor by preventing short-cycling. When
the compressor is switched from Off to On because
room temperature has risen or fallen below the
specified limit, it will remain on for at least 4 minutes.
If the temperature set-point is changed during this
4 minutes, the lock-in feature is overridden.
Automatic Emergency Heat: No more “my unit is not
heating” complaints during the middle of the night.
Heat pump units will automatically switch over to
electric resistance heat if the heat pump compressor
system fails or if the heating load is greater than the
unit capacity.
Constant Fan Mode: Take advantage of each unit’s
dual options — select continuous fan operation or
cycle the fan ON and OFF with the thermostat.
Our 7-button design allows guests to select fan
performance while allowing the owner to have the
unit revert to the desired program of continuous
fan or cycle with conditioning.
Hidden Ventilation Control: The ventilation control
lever is hidden from the occupant's view to allow you
to manage ventilation requirements.
High-Pressure Switch: Protects the unit from high
pressure and damage to the unit, helping to ensure
long unit life.
Specifications and Accessories Catalog
5
Nomenclature
PTC
07
3
G
35
AXXX
AA
1,2,3
4,5
6
7
8,9
10,11,12,13
14,15
Basic Model Type
Engineering PTC
Standard Cooler PTAC
PTH
Standard Heat Pump PTHP
DRY
Dehumid Cooler PTAC
Major & Minor Revisions
Features Code *
Nominal Cooling Capacity
A
Standard Model
C
Corrosion Protection (Seacoast)
07
7,000 BTU/h
60 Hz
D
Power Door
09
9,000 BTU/h
60 Hz
F
Fuse Holder (230/208 Only)
10
10,000 BTU/h
50 Hz
H
Hydronic Heat-­‐Capable
12
12,000 BTU/h
50 or 60 Hz
P
Condensate Pump (PTH Only)
15
15,000 BTU/h
60 Hz
Q
Quiet STC 31 Chassis
17
17,000 BTU/h
60 Hz
R
RF Antenna
V
Power Vent
Rated Voltage
X
placeholder
2
115V, 60 Hz, 1 Ph
W
Hard-­‐Wired (PTQC)
3
230/208V, 60 Hz, 1 Ph
4
265V, 60 Hz, 1 Ph
5
240/220V, 50 Hz, 1 Ph
Heater Size
00 No Electric Heat
35
15 1.5 kW
Design Series
G
3.5 kW (230/208V)
3.7 kW (265V)
25 2.5 kW
50
5.0 kW
R-­‐410A
* Use up to 4 as needed in alphabetical order. Examples:
PTC123*50AXXX
PTC073*35CRXX
PTC123*50CXXX
PTC073*25CQRW
Power Cord Configuration
Power Receptacle Configuration
Power Cord Plugs
250V Rating Power Cord Plugs with LCDI Device
NEMA 6 Configuration
30 amp
20 amp
15 amp
NEMA6-15R; 250V
receptacle used on
230/208V units
NEMA6-20R; 250V
receptacle used on
230/208V units
NEMA6-30R; 250V
receptacle used on
230/208V units
20 amp
6
www.amana-ptac.com
NEMA7-20R; 277V receptacle
used on 265V units
W
W
G
G
277V Rating Power Cord Plugs
NEMA 7 Configuration
30 amp
NEMA7-30R; 277V receptacle
used on 265V units
All units come with factor-installed power cords.
All units less than 250 volts come with LCDI device.
Product Specifications: PTC Models — Cooling/Electric Heat
230/208 Volts
Model 6, 8, 9
Voltage ³
Capacity (BTU/h)
Amps ¹⁰
Watts ¹⁰
EER
PTC
073G***XXX
230 / 208
7,700 / 7,700
3.5 / 3.5
658 / 658
11.7 / 11.7
PTC
093G***XXX
230 / 208
9,000 / 9,000
4.1 / 4.1
796 / 783
11.3 / 11.5
PTC
123G***XXX
230 / 208
12,000 / 11,700
5.6 / 5.6
1,114 / 1,085
10.4 / 10.5
PTC
153G***XXX
230 / 208
15,000 / 14,700
7.0 / 7.0
1,500 / 1,470
10.0 / 10.0
PTC
173G***XXX
230 / 208
16,400 / 16,200
8.4
1,740 / 1,720
9.4
4.2
290
264
310
282
65*
1.7
98
113
4.9
290
264
310
282
65*
2.2
102
117
6.8
290
264
310
282
65*
3.6
102
119
8.5
340
314
360
332
65*
4.4
113
130
10.2
340
314
360
332
65*
4.8
113
130
PTC
074G***XXX
265
7,700
3.0
658
11.7
PTC
094G***XXX
265
9,000
3.6
796
11.3
PTC
124G***XXX
265
12,000
4.8
1,154
10.4
PTC
154G***XXX
265
14,800
6.0
1,480
10.0
Unit without Electric Heater
Min. Circuit Amps 2, 4, 10
CFM (Cool/Wet Coil)
CFM (Dry Coil)
Ventilated Air, CFM (Fan Only)*
Dehumidification (Pints/Hr.)
Net Weight (lbs.)
Ship Weight (lbs.)
High
Low
High
Low
265/277 Volts
Model 1, 6, 8
Voltage ¹, ³
Capacity (BTU/h)
Amps ¹⁰
Watts ¹⁰
EER
Unit without Electric Heater
Min. Circuit Amps 2, 4,10
CFM (Cool/Wet Coil)
CFM (Dry Coil)
Ventilated Air, CFM (Fan Only)*
Dehumidification (Pints/Hr.)
Net Weight (lbs.)
Ship Weight (lbs.)
High
Low
High
Low
3.6
4.4
5.9
7.4
290
264
310
282
65*
1.7
98
113
290
264
310
282
65*
2.2
102
117
290
264
310
282
65*
3.6
102
119
340
314
360
332
65*
4.4
113
130
* Actual vent CFM performance will vary due to application and installation conditions.
Notes
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit PTPWHWK4 and
disconnect switch PSHW04A.
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
³ Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts. Minimum voltage on 265-volt models is 239 volts;
maximum is 292 volts.
⁴ Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be
cartridge-style time-delay fuses (included and factory-installed on all Amana® brand 265-volt chassis). See heater performance
⁵ Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric
heat at approximately 24°F outdoor ambient.
⁶ Specify two-digit heater kW size to complete model number.
⁷ R-410A refrigerant used in all systems.
⁸ All units meet or exceed ASHRAE 90.1 standards.
⁹ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
¹⁰ Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation
refers to compressor only.
Specifications and Accessories Catalog
7
Product Specifications: PTH Models — Cooling/Heat Pump/Electric Heat
Model 1, 6, 8, 9
PTH073G
**AXXX
PTH093G
**AXXX
PTH123G
**AXXX
PTH153G
**AXXX
PTH074G
**AXXX
PTH094G
**AXXX
PTH124G
**AXXX
PTH154G
**AXXX
Voltage ¹, ³
230 / 208
230 / 208
230 / 208
230 / 208
265
265
265
265
7,600 / 7,600
9,000 / 9,000
12,000 /
12,000
14,700 /
14,700
7,600
9,100
12,000
14,600
5.8 / 5.8
7.0 / 7.0
Capacity (BTU/h)
Amps ¹⁰
3.9 / 3.9
4.2 / 4.2
Watts ¹⁰
650 / 633
750 / 750
3.1
3.7
5.0
6.1
650
758
1,091
1,505
EER
11.7 / 12.0
12.0/12.0
11.0/11.0
9.7 / 9.7
11.7
12.0
11.0
9.7
4.7
5.1
7.1
8.5
3.8
4.5
6.1
7.4
High
340
330
340
390
340
330
340
390
Low
High
245
245
245
340
245
245
245
340
370
360
370
410
370
360
370
410
Low
270
270
270
370
270
270
270
370
Ventilated Air, CFM (Fan Only)*
65*
65*
65*
65*
65*
65*
65*
65*
Dehumidification (Pints/Hr.)
1.7
2.2
3.6
4.4
1.7
2.2
3.6
4.4
1,090 / 1,090 1,515 / 1,515
Unit without Electric Heater
Min. Circuit Amps 2, 4,10
CFM (Cool/Wet Coil)
CFM (Dry Coil)
Net Weight (lbs.)
108
112
115
126
108
112
115
125
Ship Weight (lbs.)
123
127
132
143
123
127
132
142
* Actual vent CFM performance will vary due to application and installation conditions.
Notes
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
³ Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
⁴ Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be
cartridge-style time-delay fuses (included and factory-installed on all Amana® brand 265-volt chassis).
⁵ Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric
heat at approximately 24°F outdoor ambient.
⁶ Specify two-digit heater kW size to complete model number.
⁷ R-410A refrigerant used in all systems.
⁸ All units meet or exceed ASHRAE 90.1 standards.
⁹ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
¹⁰ Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation
refers to compressor only.
8
www.amana-ptac.com
Product Specifications: PTC Models — Cooling (Units for Hydronic Heating)
Model 5, 6
Voltage 2
Capacity (BTU/h)
PTC
072G**XXX
PTC
092G**XXX
115
7000
115
9000
Amps
6.9
8.3
Watts
585
795
EER
11.9
11.3
Min. Circuit Amps 1, 3
8.3
290
264
310
282
10.1
290
264
310
282
Ventilated Air, (Fan Only)*
65*
65*
Dehumidification (Pints/Hr.)
1.7
2.3
CFM (Cool/Wet Coil)
CFM (Dry Coil)
High
Low
High
Low
Net Weight (lbs.)
98
102
Ship Weight (lbs.)
113
117
* Actual vent CFM performance will vary due to application and installation conditions.
Notes
¹
2
3
⁴
⁵
⁶
Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 115-volt models is 109 volts; maximum is 127 volts.
Overcurrent protection for all units without electric heaters is 15 amps.
R-410A refrigerant used in all systems.
All units meet or exceed ASHRAE 90.1 standards.
All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
Specifications and Accessories Catalog
9
Product Specifications: PTC / PTH Models — Electric Heat Performance
(Primary Heating for PTC Models; Auxiliary Heating for PTH Models; See below for Power Cord Configuration)
Voltage
Electric
Heater
Size (kW)
No. of
Stages
230/208V
1.5 / 1.3
1
230/208V
2.5 / 2.1
1
8,500
6,800
--
2,570 / 2,115
11.2 / 10.1
14.1
15
6-15 P
230/208V
3.5 / 3.0
1
12,000
9,900
--
3,570 / 2,935
15.5 / 14.1
19.5
20
6-20 P
230/208V
Nominal Heating (BTU/h)
@ 230V
@ 208V
@ 265V
5,100
4,200
--
Total
Watts6
Total
Amps
1,570 / 1,295
6.8 / 6.2
Min. Circuit MOP4
Ampacity² (amps)
8.5
15
Power
Cord
6-15 P
5.0 / 4.1
1
17,100
14,000
--
5,070 / 4,160
22.1 / 20.0
27.6
30
6-30 P
265V
1.5
1
--
--
5,100
1,570
5.9
7.4
15
7-20P
265V
2.5
1
--
--
8,500
2,570
9.7
12.2
15
7-20 P
265V
3.7
1
--
--
12,600
3,770
14.2
17.9
20
7-20 P
265V
5
1
--
--
17,100
5,070
19.2
23.9
25
7-30 P
Notes
¹
²
³
⁴
⁵
⁶
⁷
⁸
⁹
¹⁰
All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
Minimum branch circuit ampacity ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts. Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be cartridge-style
time-delay fuses (included and factory-installed on all Amana® brand 265-volt chassis).
Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric heat at
approximately 24°F outdoor ambient.
Total watts for 15,000 BTU/h models; subtract 20 watts for PT07/09/12
Specify two-digit heater kW size to complete model number.
R-410A refrigerant used in all systems.
All units meet or exceed ASHRAE 90.1 standards.
All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
Product Specifications: PTH Models — Reverse-Cycle Heating Performance
Heating
Capacity¹
PTH073G
**AXXX
PTH093G
**AXXX
PTH123G
**AXXX
PTH153G
**AXXX
PTH074G
**AXXX
PTH094G
**AXXX
PTH124G
**AXXX
PTH154G
**AXXX
230 / 208
230 / 208
230 / 208
230 / 208
265
265
265
265
BTU/h ⁵
6,800 / 6800
8,300 / 8,100
11,500 / 11,300
13,800 / 13,600
6,800
8,300
11,400
13,700
Amps ¹⁰
3.9 / 3.9
4.2 / 4.2
5.8 / 5.8
7.0 / 7.0
3.1
3.7
5.0
6.1
Watts ¹⁰
585 / 585
715 / 700
1085 /1035
1350 / 1330
585
715
1080
1340
COP ⁵
3.4 / 3.4
3.4 /3.4
3.1 / 3.2
3.0 / 3.0
3.4
3.4
3.1
3.0
370
360
370
410
370
360
370
410
Voltage ¹, ³
CFM (Dry)
COP = Coefficiency of Performance; per AHRI Test Procedures, units are rated for capacities and efficiencies.
Notes
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum branch circuit ampacity ratings conform to the National Electric Code; however, local codes should apply.
³ Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
⁴ Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must
be cartridge-style time-delay fuses (included and factory-installed on all Amana® brand 265-volt chassis).
⁵ Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric
heat at approximately 24°F outdoor ambient.
⁶ Specify two-digit heater kW size to complete model number.
⁷ R-410A refrigerant used in all systems.
⁸ All units meet or exceed ASHRAE 90.1 standards.
⁹ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
¹⁰ Refer to electric heat performance data for total MCA and recommended overcurrent protection.
Amps and Watts notation refers to compressor only.
10
www.amana-ptac.com
Accessories
Standard-Depth Sleeves
WS900E-GS
Heavy Sound Isolation Insulation Sleeve
WS900E
WS900SC
WS900DINTERNAL
Standard PTAC sleeve
Seacoast triple protected
Internal drain only for window-wall
installations (DK900D sold separately)
Outdoor Grilles
Available in stamped-aluminum or architecturally
louvered for application with an Amana brand WS900E
wall sleeve.
AGK: Extruded aluminum architectural grille available
with anodized aluminum finish or a baked-on paint
finish for durability. Choose from 3 stock colors or a
custom color to blend with your building’s exterior
color scheme. Colors include:
CB (Clear Anodized), DB (Dark Brown/Bronze)
TB (Stonewood Beige), WB (White),
SB (Special/Custom Colors)
PGK: One-piece injection molded grille using a polymer
blend of engineered thermoplastic high-impact
strength material with chemical resistance and
an exterior UV protective coating.
Choose from 3 stock colors:
DB (Dark Brown/Bronze), TB (Stonewood Beige),
WB (White)
Condensate Drain Kit
Attaches to the wall sleeve base pan for controlled
internal or external disposal of condensate.
Low-Voltage Wire Harness Kit (not shown)
For quick connections of the remote, or wired,
thermostats, wired EMS, or front desk with jumpers and
connectors.
Remote Escutcheon Kit (not shown)
Optional kit for use with units controlled via a wired,
remote thermostat. Covers control touch-pad for wired
thermostat installations.
Extra Deep Sleeves: in several depths for
thicker wall installations or special room
configurations
WS9XXD1
16" to 24" in 1" increments
WS928D1
WS930D1
WS936D1
Extra deep 28"
Extra deep 30"
Extra deep 36"
Extra deep Internal drain only
for window-wall installations
(DK900D sold separately)
WS9XXD1Interna
161/16"
Wall Sleeves
All our wall sleeves have industry standard dimensions
of 42" wide x 16⅟₁₆" high. The WS900E, SC and INTERNAL
14⅛" depth is the industry standard. Sleeves may
be shipped separately to allow for installation
during construction.
"
42"
14⅛
Standard Outdoor Grille
SGK01B
Single Pack
SGK01TB
Stonewood Beige
Architectural Outdoor Grille
AGK01CB
AGK01DB
AGK01TB
AGK01WB
AGK01SB
PGK01DB
PGK01TB
PGK01WB
DK900D
DK9001D
Anodized Aluminum
Dark Bronze/Brown
Stonewood Beige
Amana White
Custom Colors
Dark Bronze/Brown
Stonewood Beige
Amana White
Condensate Drain Kit
(use with WS900E)
Condensate Drain Kit
(use with WS900B)
PWHK01C
Wire Harness Kit
REK10B
Remote Escutcheon Kit
(10-pack)
REK10A
Remote Escutcheon Plates
SGK
AGK
or
PGK
DK900D
Each “B” kit contains 80 wires and wire nuts,
enough to attach a thermostat and one
additional accessory to 10 PTAC units. Wires
come in assorted colors for easy attachment.
Each “A” kit contains 10 Escutcheon plates only.
Specifications and Accessories Catalog
11
Accessories (cont.)
Sub-base Kit
The fully skirted sub-base conceals wiring while
providing strong support, if needed. Plug-in receptacle
and field-wiring access speeds installation. Electrical
accessories, such as fuse holders, circuit breakers and
disconnect switches, meet N.E.C. requirements.
PTSB215E
PTSB320E
PTSB330E
PTSB420E
PTSB430E
PTSB000E
115V/15A
230/208V 15/20A
230/208V 30A
265V 15/20A
265V 25A
Non-electrical
Leveling Legs
Gives wall sleeve front support and helps to level the
unit for installation.
LL2B
Leveling legs for WS9** sleeves
Hard-wire Kits
Used to permanently wire to the chassis when a
standard sub-base and power cord are not utilized.
Factory Installed Feature Code - W
PTPWHWK4 Armored Cable – all voltages
PTQC3A
Quick Connect – 230/208V
PTQC4A
Quick Connect – 265 & 115 V
Power Disconnect Switch
The PSHW**A power disconnect switch can be used
for 265-volt or 230/208-volt physical disconnect,
where required by local codes. The switch is rated
at 30-amp capacity. The switch is for use with and
Amana® brand standard sub-bases or PTPWHWK4
Hard Wire Kit.
PSHW03A
PSHW04A
230/208V
265V
Fuse Holder Kit
Cartridge-style fuses can be installed in the fuse
holder for use in the sub-base or chassis. Available in
15, 20 and 30 amp (included on 265-volt unit).
FHK315E
FHK315E
FHK320C
FHK320E
FHK330C
FHK330E
230/208V 15A
230/208V 15A (R-410A)
230/208V 20A
230/208V 20A (R-410A)
230/208V 30A
230/208V 30A (R-410A)
Circuit Breaker Kit (230/208V only)
The circuit breaker kit, available in 15, 20 or 30 amp,
can be used with Amana brand sub-bases. It gives
overcurrent protection, and its location allows you to
turn the unit on or off without tools.
CBK15C
CBK20C
15 amp Circuit Breaker Kit
20 amp Circuit Breaker Kit
CBK30C
30 amp Circuit Breaker Kit
12
www.amana-ptac.com
Accessories (cont.)
Duct Extension Kit
Extends air distribution to an adjoining room. Consists
of a main duct for the room of origin and an extension
duct to reach the adjoining room and terminal duct.
PTDK01A allows for the “B” series unit to work with the
“A” series duct kits.
MDK02B
MDK01E
EDK02B
Main Duct – R-22
Main Duct – R-410A
42" Extension Duct
Power Vent Kit
Installation of Power Vent increases CFM up to
approximately 95. Vent door will automatically close
when unit fan is off.
Extension Duct Kit
Main Duct Kit
TRANSITION
BAFFLES
TDK02B
PTDK01A
PTDK01E
Terminal Duct
Transition Duct Only – R-22
Transition Duct Only – R-410A
PVK3A
PVK4A
230/208V – R-22
265V – R-22
DGK1B
Condenser Baffle Kit
Terminal Duct Kit
Factory Installed Feature Code - V
R-410A models must have these kits installed at
the factory.
Condenser Baffle Kit
For use on non-baffled­grilles. These deflectors direct
the air in toward the center and away from the inlet to
prevent recirculation of the hot condenser air.
Condenser Baffles
Condenser
Basepan
Sub-base Extension Cover Kit
Converts older 30-amp sub-bases to allow for installation
of the larger 30-amp LCDI power cord and plugs.
SBEC10A
10 Pack
Condensate Removal Pump
Can be field-installed. Assists in removing condensate
developed by heat pump operation and transfers it to
indoor coil to dissipate into room while adding humidity
to the room.
Factory Installed Feature Code - P
CDP302
CDP402
CDP303E
230/208V – R-22
265V – R-22
230/208V – R-410A
Security Key Locks
In conjunction with the tamper-resistant front, the
installation of Amana® brand security key locks prevents
tampering of the controls used to set temperature, heating
and cooling functions. UL approved for institutional
use only.
KL03B
KL03E
Security Key Lock (R-22)
Security Key Lock (R-410A)
Specifications and Accessories Catalog
13
Accessories (cont.)
Thermostats
The following thermostats offer remote control. Any thermostat other than those listed must be submitted to Goodman Company, L.P.,
for approval prior to use.
Model #
Heat Stages
Cool Stages Fan Speed
# of Wires
Temp
Required Limiting
Backlit Display
Type
Shape &
Orientation
Connection
2246002
1
1
1
5
No
Yes
Digital
Manual
Rect./Horiz.
Wired
2246003
2
2
2
7
Yes
Yes
Digital
Manual
Rect./Horiz.
Wired
2246007
2
2
1
7
Yes
Yes
Digital
Auto-Change
Rect./Horiz.
Wired
2246008
2
2
1
7
Yes
Yes
Digital Programmable
Rect./Horiz.
Wired
DS01E*
2
2
2
0
Yes
Yes
Digital
Rect./Horiz.
Wireless
Manual
*Battery powered, but has optional hard wire capability. Requires DT01G Antennae for operation
Hydronic Heat Kit
Add-on kits fit all units allowing the addition of hydronic
water or hydronic steam heat to cooling and heating units.
The kits feature left- or right-hand piping. Unit retains
complete service access with a kit installed. Unit must be
connected to and operated by a wall thermostat.
HWK03B
HVK03B
HWK03E
HVK03E
14
Hydronic Water Kit – R-22
Hydronic Steam Kit – R-22
Hydronic Water Kit – R-410A
Hydronic Steam Kit – R-410A
www.amana-ptac.com
Hydronic Heat Kit:
Side View
Hydronic Heat Kit: Top View
Hydronic Heat Kit: Right View
Accessories (cont.)
Power Door Kit
Vent door will automatically open when unit fan is on.
Factory Installed Feature Code - D
Hydronic Valves
Water and steam valves are available for use with the
HWK03 (water) and HVK03 (steam) heat kits.
PDK3A
PDK4A
PDK3E
PDK4E
230/208V – R-22
265V – R-22
230/208V – R-410A
265V – R-410A
VS2WNCA*
VS2WNOA*
VW2WNCA*
VW2WNOA*
VW3WNC2B*
2-way/24V/NC/Steam
2-way/24V/NO/Steam
2-way/24V/NC/End Switch
2-way/24V/NO/End Switch
3-way/24V/NC/NO/End Switch
* Poptop Actuator
Wireless RF (Radio Frequency) Controls
All DigiSmart PTACs come factory-ready to be con-trolled
via wireless RF devices. 2.4 Ghz 802 15.4 protocol assures
robust communications and response.
DS01E
DD01E
DT01G
GT01G
DD01F
DP01G
DL01G
DR01G
DL01GSERIAL
Thermostat: 2-way 2
Communications
Occupancy Sensor:
EMS Activation2
Antenna / Router
Factory Installed
Feature Code - R
Generic Radio
Antenna / Router 3
Door Switch: EMS Activation2
Web-enabled Platform Server
Web-enabled Platform
Server Link BAC-NET capable
Mesh Repeater1
Serial Repeater1
Consult Amana Sales representative prior
to purchase
2 Requires DT01G for use
3 Requires DS01E for use
1
Wall Sleeve Extension Adapter Kits
Room-side extension kits to increase the depth of the
existing sleeve to allow for an industry-standard PTAC to
be installed.
Curtain Baffle Kit
The color matched polymer curtain baffles help to
prevent curtains from falling into the discharge air
stream and causing recirculation, reducing efficiencies
and shortening compressor life.
SECM1001A
1.5" Extension for 12½" Climate Master Sleeve (10 Pack)
SEZA0501A
2.5" Extension for 11½" Zone Air Sleeve (5 pack)
PTCB10B
10 Pack for R-22 units
PTCB10E
10 Pack for R-410A units
Specifications and Accessories Catalog
15
Unit with Accessory Wall Sleeve and Sub-base Accessory
Top View
42"
40"
6 - 1/ 8"
1"
9 - 9 / 16"
24 - 5 /16"
Location of external drain holes
on bottom flange of Wall Sleeve
Air
Flow
1"
Air
Flow
Air
Flow
Control
Door
Air Discharge Grille
3"
3" Clearance
to side walls
Right View
Air discharge grille is reversible to provide
either 15° or 40° discharge angle
⅞"
Stamped Grille
21½"
14⅛"
Wall Sleeve
7⅜"
Front View
58" LCDI CORD SET — 230V/208V UNIT*
42"
1⅜"
Arch Grille
LEFT
15°
R I GHT
16-1/16"
40°
2-5/8"
16¹⁄₁₆"
Hinged
Control
Door
Optional
Sub-base
3-1/4"
MIN
4"
1⅜"
¹³⁄₁₆"
11⅜"
¹³⁄₁₆"
2¾"
16
www.amana-ptac.com
½" O.D.
Copper
Drain Tube
2"
MAX
1" and ¾" Concentric knock-outs back &
bottom of sub-base (electrical only)
58" CORD
SET 230V/208V UNIT*
18" CORD
SET 265V UNIT*
Framing for Accessory Wall Sleeve (WS9XX)
Fastening Wall Sleeve
When installed in an opening, the Wall Sleeve must be
horizontally level (side-to-side) and pitched ¼ bubble
to the outside.
Alternative
Fastening Method
(Field Supplied)
(NOTE: To ensure unit’s maximum efficiency,
DO NOT over- or under-pitch.)
Installation Notes
1. If Sub-base (PTSB***E) is installed, allow minimum
3¼" height clearance and maximum 5" height
clearance between wall sleeve and floor; allow
minimum 2¾" protrusion from a finished wall.
See Note 4 if using hydronic units.
Wood Screw
Toggle Bolt
Expansion
Anchor Bolt
Mounting
Holes
(Drilled by
Installer)
2. Drain Kit (DK900D) shipped separately. Can be
mounted either right side, left side or bottom of
sleeve. If mounted to bottom of sleeve, allow
2" height clearance from floor to bottom of sleeve.
3. For UL approval, 265V units must use Amana® brand
Sub-base (PTSB***E) or Amana® brand Hard Wire
Kit (PSHW04A). Overcurrent protection on 265V units
must be by cartridge-style time delay fuses, which
are included and factory-installed on the Amana®
brand 265V chassis.
4. If Hydronic Kit (HWK03 or HVK03) is installed,
Wall Sleeve must extend exactly 3" into the room
from the finished interior wall. If using the Amana®
brand Sub-base (PTSB***E), only the minimum
3¼" height clearance between wall sleeve and floor
is permissible. Unit must also be operated with a
remote-mounted thermostat.
5. If Duct Kit (MDK***) is installed, allow a minimum of
2⅜" into the room from the finished interior wall.
Plastic
Anchor
Screws
Wall Sleeve must extend a minimum of ¼" beyond outside wall to allow for
proper caulking.
JACK STUDS
HEADER - 4" x 4" OR
DOUBLE 2"x 4" ON EDGE
MAIN STUD
16 1/4"
MIN
42
ADJUST FRAMING TO
SECURE THIS DIMENSION
1/4
"
JACK STUD
CRIPPLE
FINISHED FLOOR
SUB-FLOOR
Wall sleeve opening height should be squared with
wall sleeve opening width.
H = 16¼"
W = 42¼"
Specifications and Accessories Catalog
17
Notes
Wise Decision.
It’s an Amana® brand.
■■
■■
■■
Quiet two-fan motor system
Energy-efficient performance
DigiSmart® wireless controls on select models
Our continuing commitment to quality products may mean a change in specifications without notice.
© 2015 Goodman Company, L.P. Amana is a registered trademark of Maytag Corporation or its related
companies and is used under license to Goodman Company, L.P., Houston, TX, USA. All rights reserved.
A legacy of comfort
The impeccable reputation of
an American original
Amana heating and cooling systems are a part of the
enduring legacy of one of America’s most recognized
and respected brands. Originating eight decades ago in
Amana, Iowa, the brand is synonymous with long-lasting, premium-quality products — from home appliances
to heating and air conditioning equipment. Chances
are, you and generations before you have enjoyed the
dependable performance and longevity the Amana
brand continues to deliver.
Call your Amana brand PTAC sales representative at 800-647-2982 for complete details.
Before purchasing this appliance, read important information about its estimated annual energy
consumption, yearly operating cost, or energy efficiency rating that is available from your retailer.
www.amana-ptac.com
Our continuing commitment to quality products may mean a change in specifications without notice. © 2015 Goodman Company, L.P.
Amana is a registered trademark of Maytag Corporation or its related companies and is used under license to Goodman Company, L.P.,
Houston, TX, USA. All rights reserved.
MC-DPTAC 07-15
Supersedes 06-15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising