Amana | PTH123G35CXXX | Spec sheet | Amana PTH123G35CXXX Spec Sheet

PTAC Air Conditioners
and Heat Pumps
11.7 EER / 3.4 COP
P roduct S pecifications
Product Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Quiet operation: STC of 28
Assembled in the USA for 30 years
Increased dehumidification capacity
100% run-tested at our plant in
Fayetteville, TN, for leaks
7⅝” unit front depth: one of the shallowest
silhouettes in the industry today
Removable condenser shroud allows easy
access to enable regular cleaning of coils
Easy pull-out filters that are washable and easy to maintain
Filter drier for sealed system refrigerant
7-Button touch pad provides complete control to guests
for in-room comfort while maintaining energy efficiency
Condensate dispersion system removes condensate
from indoor cooling operation and evaporates it into
the atmosphere through the condenser
Digismart™ front desk control &
energy management software
Room freeze protection is activated when
the unit senses temperatures of 40°F or below
Versatile style that blends into any room’s color
scheme and decor
Easy to service with on-board led diagnostics
Digismart™ wireless remote thermostat is available
Remote temperature sensing for guest climate control
Extended heat pump heating down to as low
as 24°F outdoor ambient temperature
Zero floor clearance allows unit to be installed
flush to a finished floor
30-second fan-off delay
Compressor lock-in prevents compressor short-cycling
Constant fan mode
Hidden ventilation control
High-pressure switch
Control Board
First-Year Warranty: Parts & Labor
Second through Fifth Year: Parts & Labor on certain sealed system components
Second through Fifth Year: on certain functional parts only
* Complete warranty details available at ­www.amana-ptac.com.
SS-DPTAC
www.amana-ptac.com
Amana® is a trademark of Maytag Corporation or its related companies and used under license to Goodman Company, L.P., Houston, Texas.
9/14
Supersedes 8/14
Product Specifications
Nomenclature
PTC
07
3
G
35
AXXX
AA
1,2,3
4,5
6
7
8,9
10,11,12,13
14,15
Basic Model Type
Engineering PTC
Standard Cooler PTAC
Major & Minor Revisions
PTH
Standard Heat Pump PTHP
DRY
Dehumid Cooler PTAC
Features Code
A
Cooling Capacity
Standard Model
C
Corrosion Protection (Seacoast)
07
7,000 BTU/h
60 Hz
D
Power Door
09
9,000 BTU/h
60 Hz
F
Fuse Holder (230/208 Only)
10
10,000 BTU/h
50 Hz
H
Hydronic Heat-­‐Capable
12
12,000 BTU/h
50 or 60 Hz
P
Condensate Pump (PTH Only)
15
15,000 BTU/h
60 Hz
Q
Quiet STC 31 Chassis
17
17,000 BTU/h
60 Hz
R
RF Antenna
V
Power Vent
Rated Voltage
X
placeholder
2
115V, 60 Hz, 1 Ph
W
Hard-­‐Wired (PTQC)
3
230/208V, 60 Hz, 1 Ph
4
265V, 60 Hz, 1 Ph
Use up to 4 as needed in alphabetical order
5
240/220V, 50 Hz, 1 Ph
Examples:
Design Series
G
PTC123*50AXXX
PTC073*35CRXX
PTC123*50CXXX
PTC073*25CQRW
R-­‐410A
Heater Size
2
00
No Electric Heat
15
1.5 kW
25
2.5 kW
35
3.5 kW (230/208V)
3.7 kW (265V)
50
5.0 kW
www.amana-ptac.com
SS-DPTAC
Product Specifications
Product Specifications: PTC Models — Cooling/Electric Heat
230/208 Volts
Model ⁶, ⁸, ⁹
Voltage ³
Capacity (BTU/h)
Amps ¹⁰
Watts ¹⁰
EER
PTC
073G***XXX
PTC
093G***XXX
PTC
123G***XXX
PTC
153G***XXX
PTC
173G***XXX
230 / 208
7,700
3.5
670/660
11.5/11.7
230 / 208
9,000
4.1
805/785
11.2/11.5
230 / 208
11,700 / 11,500
5.6
1135/1105
10.3/10.4
230 / 208
15,000 / 14,700
7.0
1500/1470
10.0/10.0
230 / 208
16400 / 16200
8.4
1740/1720
9.4
4.2
4.9
6.8
8.5
10.2
290
264
290
264
290
264
340
314
340
314
310
282
310
282
310
282
360
332
360
332
65*
1.7
98
113
65*
2.2
102
117
65*
3.6
102
119
65*
4.4
113
130
65*
4.8
113
130
PTC
074G***XXX
PTC
094G***XXX
PTC
124G***XXX
PTC
154G***XXX
265
7,700
3.0
670
11.5
265
9,000
3.6
795
11.3
265
12,000
4.8
1,165
10.3
265
14,800
6.0
1,480
10.0
3.6
4.4
5.9
7.4
290
264
290
264
290
264
340
314
310
282
310
282
310
282
360
332
65*
1.7
98
113
65*
2.2
102
117
65*
3.6
102
119
65*
4.4
113
130
Unit without Electric Heater
Min. Circuit Amps ², ⁴, ¹⁰
CFM (Cool/Wet Coil)
CFM (Dry Coil)
High
Low
High
Low
Ventilated Air, CFM (Fan Only)*
Dehumidification (Pints/Hr.)
Net Weight (lbs.)
Ship Weight (lbs.)
265/277 Volts
Model 1, 6, 8
Voltage ¹, ³
Capacity (BTU/h)
Amps ¹⁰
Watts ¹⁰
EER
Unit without Electric Heater
Min. Circuit Amps ², ⁴, ¹⁰
CFM (Cool/Wet Coil)
CFM (Dry Coil)
Ventilated Air, CFM (Fan Only)*
Dehumidification (Pints/Hr.)
Net Weight (lbs.)
Ship Weight (lbs.)
High
Low
High
Low
* Actual vent CFM performance will vary due to application and installation conditions.
Notes
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit PTPWHWK4 and
disconnect switch PSHW04A.
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
³ Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts. Minimum voltage on 265-volt models is 239 volts;
maximum is 292 volts.
⁴ Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be
cartridge-style time-delay fuses (included and factory-installed on all Amana® brand 265-volt chassis). See heater performance
⁵ Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric
heat at approximately 24°F outdoor ambient.
⁶ Specify two-digit heater kW size to complete model number.
⁷ R-410A refrigerant used in all systems.
⁸ All units meet or exceed ASHRAE 90.1 standards.
⁹ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
¹⁰ Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation
refers to compressor only.
SS-DPTAC
www.amana-ptac.com
3
Product Specifications
Product Specifications: PTH Models — Cooling/Heat Pump/Electric Heat
Model ¹, 6, 8, 9
Voltage ¹, ³
Capacity (BTU/h)
Amps ¹⁰
PTH073G
**AXXX
PTH093G
**AXXX
PTH123G
**AXXX
PTH153G
**AXXX
PTH074G
**AXXX
PTH094G
**AXXX
PTH124G
**AXXX
PTH154G
**AXXX
230 / 208
230 / 208
230 / 208
230 / 208
265
265
265
265
7,700
9,000
12,000
14,400
7,700
9,100
12,000
14,400
3.9
4.2
5.8
7.0
3.1
3.7
5.0
6.1
Watts ¹⁰
650 / 650
785 / 785
1,120 / 1,120
1,480 / 1,480
650
790
1,120
1,480
EER
11.7 / 11.7
11.5 / 11.5
10.7 / 10.7
9.7 / 9.7
11.7
11.5
10.7
9.7
4.7
5.1
7.1
8.5
3.8
4.5
6.1
7.4
Unit without Electric Heater
Min. Circuit Amps ², ⁴, ¹⁰
CFM (Cool/Wet Coil)
High
340
330
340
390
340
330
340
390
Low
245
245
245
340
245
245
245
340
High
370
360
370
410
370
360
370
410
Low
270
270
270
370
270
270
270
370
Ventilated Air, CFM (Fan Only)*
65*
65*
65*
65*
65*
65*
65*
65*
CFM (Dry Coil)
Dehumidification (Pints/Hr.)
1.7
2.2
3.6
4.4
1.7
2.2
3.6
4.4
Net Weight (lbs.)
108
112
115
126
108
112
115
125
Ship Weight (lbs.)
123
127
132
143
123
127
132
142
* Actual vent CFM performance will vary due to application and installation conditions.
Notes
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
³ Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
⁴ Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be
cartridge-style time-delay fuses (included and factory-installed on all Amana® brand 265-volt chassis).
⁵ Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric heat
at approximately 24°F outdoor ambient.
⁶ Specify two-digit heater kW size to complete model number.
⁷ R-410A refrigerant used in all systems.
⁸ All units meet or exceed ASHRAE 90.1 standards.
⁹ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
¹⁰ Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation refers to compressor only.
4
www.amana-ptac.com
SS-DPTAC
Product Specifications
Product Specifications: PTC Models — Cooling (Units for Hydronic Heating)
Model 5, 6
PTC
072G00XXX
PTC
092G00XXX
115
7000
115
9000
Voltage 2
Capacity (BTU/h)
Amps
6.9
8.3
Watts
EER
585
11.9
795
11.3
CFM (Cool/Wet Coil)
High
Low
8.3
290
264
10.1
290
264
CFM (Dry Coil)
High
Low
310
282
310
282
Ventilated Air, (Fan Only)*
65*
65*
Dehumidification (Pints/Hr.)
1.7
2.3
Net Weight (lbs.)
98
102
Ship Weight (lbs.)
113
117
Min. Circuit Amps 1, 3
* Actual vent CFM performance will vary due to application and installation conditions.
Notes
¹ Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
2 Minimum voltage on 115-volt models is 109 volts; maximum is 127 volts.
3 Overcurrent protection for all units without electric heaters is 15 amps.
⁴ R-410A refrigerant used in all systems.
⁵ All units meet or exceed ASHRAE 90.1 standards.
⁶ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
Product Specifications: PTC / PTH Models — Electric Heat Performance
(Primary Heating for PTC Models; Auxiliary Heating for PTH Models; See below for Power Cord Configuration)
Voltage
Electric
Heater
Size (kW)
No. of
Stages
Nominal Heating (BTU/h)
@ 230V
@ 208V
@ 265V
Total
Watts ⁶
Total
Amps
Min. Circuit MOD ⁴
Ampacity² (amps)
Power
Cord
230/208V
2.5
1
8,500
6,800
--
2,570 / 2,115
11.2 / 10.1
14.1
15
6-15 P
230/208V
3.5
1
12,000
9,900
--
3,570 / 2,935
15.5 / 14.1
19.5
20
6-20 P
230/208V
5
1
17,100
14,000
--
5,070 / 4,160
22.1 / 20.0
27.6
30
6-30 P
265V
2.5
1
--
--
8,500
2,570
9.7
12.2
15
7-20 P
265V
3.7
1
--
--
12,600
3,770
14.2
17.9
20
7-20 P
265V
5
1
--
--
17,100
5,070
19.2
23.9
25
7-30 P
Notes
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum branch circuit ampacity ratings conform to the National Electric Code; however, local codes should apply.
³ Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts. Minimum voltage on 265-volt models is 239 volts;
maximum is 292 volts.
⁴ Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be
cartridge-style time-delay fuses (included and factory-installed on all Amana® brand 265-volt chassis).
⁵ Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric
heat at approximately 24°F outdoor ambient.
⁶ Total watts for 15,000 BTU/h models; subtract 20 watts for PT07/09/12
⁷ Specify two-digit heater kW size to complete model number.
⁸ R-410A refrigerant used in all systems.
⁹ All units meet or exceed ASHRAE 90.1 standards.
¹⁰ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
SS-DPTAC
www.amana-ptac.com
5
Product Specifications
Product Specifications: PTH Models — Reverse-Cycle Heating Performance
Heating
Capacity¹
Voltage ¹, ³
BTU/h ⁵
PTH073G
**AXXX
PTH093G
**AXXX
230 / 208
6,800 / 6,800
230 / 208
8,300 / 8,100
PTH123G
**AXXX
PTH153G
**AXXX
230 / 208
230 / 208
11,500 / 11,300 13,800 / 13,600
PTH074G
**AXXX
PTH094G
**AXXX
PTH124G
**AXXX
PTH154G
**AXXX
265
6,800
265
8,300
265
11,400
265
13,700
Amps ¹⁰
3.9
4.2 / 4.2
5.8 / 5.8
7.0 / 7.0
3.1
3.7
5.0
6.1
Watts ¹⁰
585 / 570
715 / 700
1085 /1035
1350 / 1330
570
715
1080
1340
COP ⁵
CFM (Dry)
3.4 / 3.5
370
3.4 / 3.4
360
3.1 / 3.2
370
3.0 / 3.0
410
3.5
370
3.4
360
3.1
370
3.0
410
COP = Coefficiency of Performance; per AHRI Test Procedures, units are rated for capacities and efficiencies.
Notes
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum branch circuit ampacity ratings conform to the National Electric Code; however, local codes should apply.
³ Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
⁴ Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must
be cartridge-style time-delay fuses (included and factory-installed on all Amana® brand 265-volt chassis).
⁵ Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric
heat at approximately 24°F outdoor ambient.
⁶ Specify two-digit heater kW size to complete model number.
⁷ R-410A refrigerant used in all systems.
⁸ All units meet or exceed ASHRAE 90.1 standards.
⁹ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
¹⁰ Refer to electric heat performance data for total MCA and recommended overcurrent protection.
Amps and Watts notation refers to compressor only.
Contractor's Bid Sheet
Furnish and install air-cooled through-the-wall package terminal air conditioners amd heat pumps (assembled in the USA).
Units are rated in accordance with the ARI (Air Conditioning & Refrigeration Institute) Standards 310/380-93, CSA (Canadian
Standards Association) EEV certification programs and listed by U. L. (Underwriters Laboratories).
Ratings
Each unit must meet the following specifications:
ARI rating of _________BTUH cooling (and _________ BTUH
reverse cycle heating with a COP of _________ at 47° F O.D.)
Electric resistance heat of _________ BTUH. Total Amp draw
must be of ________ and _________ Watts at _________ volts.
The unit must remove a minimum of _________ pints of
moisture per hour when operated at rating conditions. The EER
must be a minimum of _________ EER.
Unit Chassis
Each unit must be slide out design shipped with room cabinet
front installed. Unit chassis must have the ability to be installed
with 0 clearance from finished floor. An electrical power cord
must be included with chassis and installed by the manufacturer
to assure proper NEMA 6 or 7 configuration and UL-approved
length. Units less than 250 volts must also have a LCDI power cord.
Unit must be tested for conformance to ASTME water infiltration
specification ASTME 331-86, which ensures no water infiltration
when tested at 8" rain per hour at 63 mph wind for 15 minutes.
Room Cabinet
The monochromatic front of the room cabinet must be able to
be field-secured to chassis to inhibit tampering. Filter must be
accessible without removing room front. Cabinet depth must
not exceed 7⅝” to minimize unit’s impact on room space.
6
Coils
Unit’s coils must have rifled copper tubing expanded into
rippled-edge louvered aluminum fins. Exterior coil must be of
a two-row bent coil design with removable shroud top to allow
easy-access for cleaning of the exterior coil.
Heat Pumps
Each unit must include a change-over thermistor that senses an
outside ambient switch-over temperature as low as 24°F, lockopen refrigerant reversing valve during heat pump operation,
temperature-activated defrost drain and automatic emergency
heat operation to override the heat pump’s change-over
thermostat and bring on electric resistance heaters in the event
of a sealed system failure. Unit must not operate compressor
and electric heaters simultaneously.
Compressor
The compressor must be hermetically sealed, internally isolated,
rotary-type and permanently mounted on rubber isolators. No
removal or adjustment of compressor hold-down bolts is to be
required during installation.
Warranty
The warranty is for Full One Year on the entire unit; Full 2nd through
5th Year on the entire sealed refrigerant system components;
Limited Second through Fifth Year on functional parts only.
www.amana-ptac.com
SS-DPTAC
Product Specifications
Unit Digital Controls
The unit’s control must be completely wired and accessible from
the top of the chassis. Controls shall be a LED touch-pad design
with seven large, easy-to-read and use buttons: Heat – Cool –
Off – Fan – Temp+ (plus) – Temp- (minus) and two red sevensegment LED temperature displays. Unit shall have a green
status LED to advise owner of operational diagnostic messages.
Unit shall have one-button activation via membrane touch-pad.
Unit control board shall have an 18-pin low-voltage connector
to allow for easy connection to remote wired devices. Unit shall
have two serial-port connectors for easy connection to wired or
wireless EMS (Energy Management Systems).
Unit must have the ability to easily configure owner-selectable
and programmable functions:
• Fan-cycle operation
• Electronic temperature limiting for cooling
• Electronic temperature limiting for heating
• Enhanced dehumidification cooling operation
• Unoccupied 18-hour temperature set-back
• Un-rented temperature set-back
• Multiple unit twinning to one wired thermostat
• Load-shedding operation
• Front-desk on-off or temperature set-back
Unit must be able to connect to approved remote devices:
• Wired thermostat
• Wired door motion sensor
• Wired room motion sensor
• Wired room-to-room transfer fan
• Front Desk Control
• Future RF wireless communications devices
Unit must be able to acquire and display operational temperature
data from up to six installed thermistors to include:
• IAT—Indoor air temperature (black)
• ICT—Indoor coil temperature (red )
• IDT—Indoor discharge temperature (yellow)
• OCT—Outdoor coil temperature (blue) (heat pumps
& Wireless cooler models)
• OAT— Outdoor Air Temperature (Wireless-ready
models only)
• Orange—Miscellaneous thermistor or analog device (optional)
Evaporator/Condenser Fans
Direct drive with a permanent, split-capacitor, two-speed
indoor motor. Condensate must be directed onto the back and
sides of the coil to aid in evaporation and removal.
Air Discharge
Must be a sloped surface so that obstructions cannot be placed
on the unit. Discharge conditioned air can be directed into the
room at an angle of 16 or 56 degrees from the vertical position.
The discharge grille must be of polycarbonate material to resist
bending, cracking, rusting and corrosion.
New installations typically require a minimum of WS900E wall sleeve and an outdoor grille.
Wall Sleeves (WS900E)
The wall sleeve must be industry-accepted dimensions:
14⅛” depth x 42” width x 16¹/₁₆” height and constructed of
G90 HDG galvanized steel with a baked corrosion-inhibiting
urethane primer and baked-polyester topcoat enamel.
Sleeve must be insulated and shipped with a weather
resistant rear closure panel installed.
Outdoor Grilles
Outdoor grille must be architecturally extruded, louvered
aluminum (AGK01*B), one-piece polymer-blend injection
molded louver (PGK01*B) or standard stamped aluminum
(SGK**B). All other grilles must be submitted to the PTAC
manufacturer for feasibility, airflow characteristics and
compliance with UL regulations, where necessary.
The optional accessories listed below perform specific functions required in some installations.
Condensate Drain Kit (DK900D)
Power Vent & Damper
Sub-base Kit (PTSB***E)
Fuse Holder (included in 265V chassis)
Attaches to the bottom of the wall sleeve for directionalcontrolled internal or external disposal of condensate,
defrost or rain water.
Necessary for UL listing requirements for 265V units (Hard
Wire Kit may be substituted for Sub-base kit). Optional for
230/208V units. Must be pre-wired to facilitate field-electrical
connections and include an NEMA 6 or 7 configuration
electrical receptacle. It must have two leveling screws for
sleeve support and accurate unit leveling during installation.
Locations for field installation of physical disconnect
switches, cartridge-style fuse holders and circuit breakers
must be provided. Side-skirts must be provided with subbases. (PTSB000E Non-Electrical Sub-base available.)
SS-DPTAC
Must be provided to maximize ventilation air intake to up to
approximately 95 CFM. Power vent must be off and damper
door closed when unit fan is de-energized.
Must be installed either in the unit or the sub-base and must
match the electrical requirements of the chassis.
Security Key Locks (KL03E)
Must be installed to prevent tampering of the unit controls.
Unit room cabinet must also be secured to the chassis with
field supplied screws. UL-approved for institutional use only.
Disconnect Switch
Power disconnect switch must be installed in sub-base for
use as a physical disconnect, where required by local codes.
www.amana-ptac.com
7
Product Specifications
Contractor's Bid Sheet (cont.)
Duct Kits (MDK01E, EDK02B, TDK02B, PTDK01E, DDK01E)
Three kits must be supplied to provide ducted, conditioned
air into a second room: a main duct kit, an extension duct kit
and a terminal duct kit.
Hydronic Heat Kit
Is required for heating functions instead of electric resistance
heaters. Unit must retain complete service access with the
kit installed. Proper water or steam valves must be used.
Condensate Removal Pump (Heat Pumps only)
Must be installed to assist in removing the condensate
developed by the heat pump operation and transfer it to the
indoor coil to dissipate into the room, adding humidity to
the room.
Circuit Breaker Kit
Must be installed in sub-base to provide overcurrent
protection for proper 230/208V amperage. Can also be
used as a physical disconnect where local codes permit for
230/208 voltage.
Hard Wire Kit
Must be used to permanently wire chassis for hard wire
purposes. (For 265V units, Hard Wire Kit may be substituted
with Sub-base Kit.)
Thermostats
A manufacturer-approved manual, auto changeover
or programmable traditionally wired thermostat must
be installed to provide full remote operation of the chassis.
A Remote Escutcheon Kit must be used to indicate remote
operation.
Monthly Maintenance
Intake Air Filters
It is extremely important to clean the inlet air filters once a month (or more often if operated in dusty or dirty locations or
conditions) to properly maintain the operational performance of the PTAC unit. The two intake air filters (constructed of
durable polypropylene) can be easily inserted into the cabinet front using the cabinet filter guides. Before cleaning the intake
filters, turn the unit off by setting the mode switch to the OFF position. Filters should be cleaned as required. The following
procedure is used to remove the intake filters:
1. Facing the unit, pull up on the filter handles located at the front top of the unit.
2. Pull each filter upward and remove.
3. Clean filters with vacuum or with running water. Reverse this procedure to reinstall the filters.
Note: Accessory filter kits are available from your sales person. All filters are permanent and cleanable. Consult your
I&O Manual for other monthly cleaning instructions.
Spare Filters
Helps keep dirt and lint out of the air and off the coil,
thus increasing the unit's efficiency. Amana® brand
filters are easy to remove, wash and replace.
Replacement Charcoal Filter Kit
Absorbs airborne odors caused by cigarette, pipe
or cigar smoke and odors caused by mold, mildew,
etc. Filters are made of polyester fibers coated with
activated charcoal and are individually wrapped.
These filters are permanent and can be washed or
cleaned. Call your Amana® brand PTAC sales person
for details. 10 filters per pack.
FK10A
10-pack - A Series
FK10B
10-pack - B, C & D Series
FK10E
10-pack - E Series
(requires 2 filters per
change.)
CFK10A
10-pack - A Series (R-22)
CFK10B
10-pack - B, C & D Series (R-22)
Amana® is a trademark of Maytag Corporation or its related companies and used under license to Goodman Company, L.P. All rights reserved. Our continuing commitment to quality products may mean a change in specifications without notice. © 2014 • Goodman Company, L.P. • Houston, Texas • Printed in the USA.
8
www.amana-ptac.com
SS-DPTAC
Download PDF

advertising