Whirlpool | UDT518SAFP | Dimension Guide | Whirlpool UDT518SAFP Dimension Guide

Whirlpool UDT518SAFP Dimension Guide
Undercounter Dishwasher
PRODUCT MODEL NUMBERS
Water Supply Requirements
■■ A
hot water line with 20-120 psi (138-862 kPa) water pressure.
(49°C) water at dishwasher.
■■ 3/8" O.D. copper tubing with compression fitting or flexible
stainless steel braided fill line (1/2" minimum plastic tubing is
not recommended).
■■ A 90° elbow with 3/8" N.P.T. external pipe threads on one end.
Do not solder within 6" (15.2 cm) from water inlet valve.
UDT518SAFP
■■ 120°F
Location Requirements
There must be a minimum of 255/8" (65.1 cm) in front of
dishwasher to allow door to open fully.
Countertop
Product Dimensions
22" (59 cm)*
Dishwasher
255/8"
(65.1 cm)
321/2" (82.6 cm) min.
35" (88.9 cm) max.
2" (5.1 cm) min.
clearance for door
opening
18"
(45.7 cm)
Electrical Requirements
■■ 120
■■
volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical supply
Wiring must be 2-wire with ground
We recommend:
21/2"
(6.2 cm)
*To front of door frame
SIDE VIEW
171/2" (44.5 cm min.
18"(45.7 cm) max.
■■ A
time-delay fuse or circuit breaker
■■ A separate circuit
Drain Requirements
■■ Use
the new drain hose supplied with your dishwasher. If this is
not long enough, use a new drain hose with a maximum length
of 10 ft (3.05 m) that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, use 5/8" (1.58 cm)
or 7/8" (2.2 cm) inside diameter hose and a coupler to connect
the two hose ends. Secure the connection with 2 clamps.
■■ Connect drain hose to waste tee or disposer inlet above drain
trap in house plumbing and 32" (81.3 cm) minimum above the
floor. It is recommended that the drain hose either be looped
up and securely fastened to the underside of the counter, or be
connected to an air gap.
■■ Use an air gap if the drain hose is connected to house
plumbing lower than 18" (45.7 cm) above floor.
Air gap
REAR VIEW
Use 1/2" minimum I.D. drain line fittings.
■■ Do not connect drain lines from other devices to the
dishwasher drain hose.
■■
Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
specifications without notice.
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.
Page 1 of 2
W10702387-D-WH
5/16
Cabinet Cutout Dimensions
Cut holes in shaded area of cabinet walls or floor for plumbing
and electrical service.
323/4" to 341/2"*
(83 cm to 88 cm)
NOTE: ADA installation, 321/2" (82.5 cm) beneath 34" (86.4 cm)
high countertops may be accomplished by adjusting the toekick
and leveling legs.
All surfaces must be
free from instrusions
24"
(61 cm)
min.
4"
(10.2 cm)
6"
(15.2 cm)
175/8" (44.8 cm) min.
18" (45.7 cm) max.
* Underside of countertop to floor
Custom Panel Dimensions and Installation
0.59" (1.5 cm)+
16.48" (41.8 cm)+
26.77" (68.0 cm)+
H
)+
cm m) 15.35" (39.0 cm)+
2
0c
(0.
8" (0.1
0
.
"
0 39
.
-φ
12 ep 0
e
d
ole
1.18" (3.0 cm)
6.79" (17.25 cm)+
2.56" (6.5 cm)+
17.64" (44.9 cm)+
Custom panel should be constructed according to diagram below.
1.50" (3.8 cm)+
7.05" (17.9 cm)+
6.89" (17.5 cm)+
17.4" + (44.4 cm)
Install the hook on the custom wood panel and insert the hook into the slot on the outer door of the dishwasher. After positioning the
panel, attach the panel to the outer door with screws and bolts.
Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
specifications without notice.
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.
Page 2 of 2
W10702387-D-WH
5/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising