Liebherr | CS1360B | Installation instructions | Liebherr CS1360B Installation Instructions

Installation
Instructions
For NoFrost Combined
Refrigerator-Freezers with IceMaker
CS 1360
7085 561-00
Important
Please Read and Follow these
Instructions
These instructions contain Danger, Warning and
Caution notes.
This information is important for safe and efficient installation and operation.
Always read and comply with all Danger, Warning and
Caution notes!
DANGER!
Danger indicates a hazard which
will cause serious injury or death if
precautions are not followed.
WARNING!
Warning indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.
CAUTION!
Caution indicates a potentially hazardous
situation which, if not avoided, may result
in minor or moderate injury.
IMPORTANT
This indicates information that is especially
relevant to a problem-free installation and
operation.
Note to the Installer
It is very important to follow the instructions in the
manual to ensure proper installation and operation of
the unit.
Before installing the unit, be sure to thoroughly read
and understand all of the information in this manual.
WARNING!
Electrocution hazard.
Do not connect to the electrical outlet
before the installation is completed.
2
Content
Page
Please Read and Follow these Instructions.................. 2
Note to the Installer......................................................... 2
R600a Refrigerant.......................................................... 2
Disposal of Old Appliance.............................................. 3
Disposal of Carton.......................................................... 3
Electrical Safety.............................................................. 3
Blocking for Safety.......................................................... 3
Appliance Dimensions.................................................... 4
Cabinet Opening Dimensions........................................ 5
Unit Venting..................................................................... 6
Leveling the Appliance................................................... 6
Mounting the anti tipping device.................................... 7
Safety Instructions and Warnings ................................... 8
Water Connection Requirements................................... 8
Water Connection Adapter............................................. 8
Connection to the Water Supply.................................... 9
Changing Over Door Hinges.........................................10
R600a Refrigerant
WARNING!
The refrigerant contained within the
appliance R600a is environmentally
friendly, but flammable. Leaking
refrigerant can ignite.
To prevent possible ignition follow
the warnings below:
• Keep ventilation openings, in
the appliance enclosure or in
the built-in structure, clear of
obstruction.
• Do not damage the refrigerant
circuit.
• Component parts and power cords
shall be replaced with like components
performed by factory authorized service
personnel only.
Safety
Disposal of Old Appliance
DANGER!
Risk of child entrapment.
Child entrapment and suffocation are not problems of
the past.
Junked or abandoned refrigerators are still dangerous –
even if they will sit for “just a few days.”
If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.
Electrical Safety
Connect this appliance to a 15 amp or 20 amp, 110120 VAC, circuit which is grounded and protected by a
circuit breaker or fuse.
We recommend using a dedicated circuit for this appliance to prevent circuit overload and the chance of interruption to the appliance.
This appliance is equipped with a three-prong (grounding) polarized plug for your protection against possible
shock hazards.
Before you discard old appliances:
• Take off the doors.
Where a two-prong wall receptacle is encountered,
contact a qualified electrician and have it replaced with
a properly grounded three-prong receptacle in accordance with all local codes and ordinances.
• Leave the shelves in place so that children may not easily climb inside.
Disconnect power before installing optional Side By
Side Kit.
• Cut off the power cable from the discarded refrigerator. Discard separately from
the refrigerator.
• Be sure to follow your local requirements
for disposal of appliances.
Contact the trash collection agency in
your area for additional information.
Disposal of Carton
The packaging is designed to protect the appliance and
individual components during moving and is made of
recyclable materials.
WARNING!
Keep packaging materials away from
children. Polythene sheets and bags can
cause suffocation!
Please recycle packaging material where facilities are
available.
WARNING!
Electrocution hazard.
Electrical grounding required.
• Do not remove the round grounding
prong from the plug.
• Do not use extension cords or
ungrounded (two prong) adapters.
• Do not use a power cord that is frayed or
damaged.
•
Do not use a power strip.
Failure to follow these
instructions may result in fire,
electrical shock or death.
Blocking for Safety
WARNING!
To avoid a hazard due to instability of the
appliance, it must be fixed in accordance
with the instructions.
3
Planning Information
Appliance Dimensions
Overall height of the appliance can be increased
by a maximum of 5/8” (see Leveling the appliance).
4
Planning Information
Cabinet Opening Dimensions
The appliance can be used freestanding or semi built-in.
If semi built-in, please consider the cabinet opening dimensions.
This is where the
power cord extends
from the back of the
appliance.
Free length of
the power cord =
98 inch (2500 mm).
IMPORTANT
The power plug must be easily accessible so that the appliance can be disconnected from the mains
quickly in an emergency. It must not be behind the back of the appliance.
NOTE
If the gap between the rear of the appliance and the wall is less than 2 inch (51 mm) , the power consumption
level may increase.
5
Installation
Unit Venting
Leveling the Appliance
Do not restrict the air flow.
The ventilation opening can either be directly over the
appliance
, above the cabinet and below the ceiling
or through a vent installed in a soffit
.
1
2
3
IMPORTANT
The clear ventilation cross-section must be at
least 31 in² (200 cm²) from the lower ventilation
opening right to the upper one.
The section below the freezer door and the floor
must not be covered.
The height can be
adjusted in front by twisting the leveling feet.
22 mm
wrench
Twist the adjusting bolt to set up
the back of the appliance. Align
the appliance with sides of kitchen
cabinets by adjusting leveling feet
and the supports.
5 mm socket
IMPORTANT
After final installation, this screw must be turned
down until it has proper floor contact to support
the hinge bracket.
6
Blocking For Safety
Mounting the anti tipping device
WARNING!
Tip over hazard!
The anti tipping bracket must be mounted
to prevent the appliance from tipping
when the fully stocked door is opened.
IMPORTANT
Be sure that there is no plumbing or electrical
wiring located in this area which screws or drills
could damage.
1. Mark the center of the appliance on the back wall.
2. Mount the anti tipping bracket.
Center line of appliance.
IMPORTANT
The screws for fastening the anti-tip device are
not supplied with the appliance. Appropriate
screws must be used for the material (wood,
concrete, etc.) in which the safety device is
mounted.
7
Ice Maker
Safety Instructions and Warnings
• Do not install the water connection while the combined refrigerator-freezer is connected to an electrical outlet.
• The connection to the water supply may only be
made by a trained and licensed plumber.
• All equipment and devices used to supply the water
to the appliance must comply with the current regulations for your geographical area.
WARNING!
Water Connection Adapter
IMPORTANT
Only use the supplied adapter for connection
to the solenoid valve. The solenoid valve has a
metric R3/4 male connector. Any attempt to use
other adapters for connection could damage the
thread on the solenoid valve.
The supplied adapter enables different connection
options for different kinds of water lines. A water line is
not supplied with the appliance.
Connect to potable water supply only.
Seal
Water Connection Requirements
• The water supply pressure requirements are different
based on whether or not the supplied Liebherr water
filter is installed.
With the filter installed, the pressure must be in the
range of 40-90 psi (2.8-6.2 bar).
Without the filter installed, the acceptable pressure
range is 22-87 psi (1.5-6 bar).
Failure to meet these requirements will likely result
in ice maker malfunction and possibly cause a water
leakage that can damage flooring and surrounding
furniture.
Valve connector (union nut
for connection to the solenoid valve)
Connects to 1/4" compression end
Angle connector
Connects to 1/4" compression end
Union nut with compression ring for
use with 1/4" OD copper lines
The connection to the valve connector can be done with
or without the angle connector, as required.
• A shut-off valve, must be installed between the hose
line and the main water supply so the water supply
can be stopped if necessary.
Braided style ice maker hoses can be connected directly
to the threaded ends.
IMPORTANT
For connection with 1/4" OD copper lines, use the union
nut with compression ring.
Do not install the shut-off valve behind the appliance.
IMPORTANT
Make sure that the connection is fitted with a seal
and is tight.
• Insert the water strainer supplied into the
valve connector.
8
Ice Maker
Connection to the Water Supply
1. Move the appliance towards the final position and
leave enough space to work behind.
2. Remove the cover from the solenoid valve.
5. Screw the adapter
onto the solenoid
valve.
6. Move the power supply line to the area of the electrical outlet.
WARNING!
3. Connect the water line to the adapter in
the respective configuration, depending
on the type of water line used.
The figure shows the configuration with a copper line
as an example.
Do not connect to the electrical outlet
before the installation is completed and
the water line is connected to the solenoid
valve.
7. Push the appliance slowly to the back wall. Make
sure the water line does not interfere with the anti tipping bracket(s).
8. Open the shut-off valve for the water supply and
check the entire water system for leaks.
4. Bleed the air from the water line by opening
the water supply temporarily.
9
Reversing Door Hinges
Changing Over Door Hinges
Door hinges should only be changed by a trained
expert.
5.
Changing over the door hinges requires two people.
6.
1.
7.
5.
Unscrew hinge bracket.
6.
Transfer cover plate to the opposite side.
7.
Turn hinge bracket through 180°
and screw into place.
IMPORTANT
The door must now be held secure
by another person.
1. Remove cover from upper door
mounting and unscrew door.
8.
2.
8.
2.
Remove hinge bushing, turn
through 180° and re-fit.
10.
Transfer cover plate to the opposite side.
IMPORTANT
The door must now be held secure by another
person.
11.
3.
9.
4.
Tilt appliance slightly backwards and
unscrew the adjustable foot.
10. Remove the hinge pin.
11. Unscrew hinge bracket.
10
3.
Pull out middle hinge pin.
4.
Remove bottom door.
9.
Reversing Door Hinges
17.
12. Transfer the hinge component on the hinge bracket
to the opposite side.
18.
12.
Both doors
18.
17 Release pressure plates at
the front 1 and pull them
backwards to remove 2.
18. Transfer door handle and
plugs to the opposite side.
13. Transfer cover to the opposite side.
13.
Both doors
19. Transfer spring clip to the opposite side.
14.
15.
20.
14. Transfer cover plate to the opposite side.
15. Screw hinge bracket into place.
20. Suspend bottom door on
hinge pin.
IMPORTANT
The door must now be held secure by another
person.
21.
16.
16. Tilt appliance slightly backwards, insert
pin and attach using the adjustable foot.
21. Insert middle hinge pin.
11
Reversing Door Hinges
IMPORTANT
The door must now be held secure by another
person.
22.
25.
22. Using a screwdriver, push out
the hinge and remove it from
the door .
25. Suspend top door on hinge
pin. For this, the door must
be open at least 90°.
23.
26.
23. Using a screwdriver, push out
the plug and transfer it to the
opposite side.
26. Secure door with screws
and click cover into place.
24.
24. Insert hinge.
27.
27. Place the appliance in its final position at the place of installation.
Extend the adjustable foot at the
bottom hinge bracket until it rests
on the floor and then make a further
90° turn.
12
Download PDF

advertising