Hotpoint | HTX24GASKWS | Specifications Sheet | Hotpoint HTX24GASKWS Specifications Sheet

Hotpoint HTX24GASKWS Specifications Sheet
HTX24GASKWS
Hotpoint® 6.2 cu. ft. capacity aluminized alloy gas dryer
22 1/2"
26 3/4"
POWER
DRYER DIMENSIONS (IN INCHES)
11 3/4"
EXHAUST OPTIONS: 3-way via rear, left and bottom. Dryer is shipped exhausted to the
rear. Alternate exhausting knockouts are supplied.
CIRCUIT REQUIREMENTS: An individual properly-grounded branch circuit, with a
three-prong grounding-type receptacle, protected by a 15- or 20-amp circuit breaker or a
time-delay fuse is required.
GAS DRYER ELECTRIC RATING: 120V, 60Hz, 6 Amp
44"
37 1/2"
GAS (BTU/HR): 22,000. Factory-equipped for natural gas. Tested for LP gas. LP gas
supply requires an optional conversion kit. Check installation instructions for ­correct kit
and have a qualified gas technician install a conversion kit. See dryer ducting information
for proper installation.
4 1/4"
1 3/4"
4"
INSTALLATION INFORMATION: For complete information, see installation instructions
packed with product for current dimensional data.
SPECIAL INSTALLATION REQUIREMENTS ALCOVE OR CLOSET INSTALLATION:
- If your dryer is approved for installation in an alcove or closet, it will be stated
on a label
22 1/2"
on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side, 1" front, top and rear
- Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60
sq. in. of open area equally distributed. If this closet contains both a washer and a dryer,
doors must contain a minimum of 120 sq. in. of open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
SIDE VIEW
26 3/4"
27"
POWER CORD 4 1/2"
11 3/4"
BATHROOM OR BEDROOM INSTALLATION:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local codes, with
the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
44"
37 1/2"
4 1/4"
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
Minimum clearances to combustible surfaces 0" both sides, 1" rear
1 3/4"
4"
SIDE VIEW
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
3 1/4"
5"
3 1/4"
REAR VIEW
Specification Revised 5/16
GE Dryer Vent
HTX24GASKWS
GE Dryer Vent
Hotpoint® 6.2 cu. ft. capacity aluminized alloy gas dryer
For complete information, see installation instructions packed with your
dryer.
DUCTING MATERIALS:
For best performance, this dryer should be vented with 4" diameter all
rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed
flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In
special installations, it may be necessary to connect the dryer to the house
vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foiltype) duct may be used ONLY in installations where rigid metal or flexible
metal (semi-rigid) ducting cannot be used AND where a 4” diameter can be
maintained throughout the entire length of the transition duct. Please see
installation instruction packed with your dryer for complete instructions
when using flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If you
exhaust to the side or bottom of dryer, add one turn.
2. The
maximum length of 4' rigid (aluminum or galvanized) duct which
can be tolerated is shown in the table.
turn of 45° or less may be ignored. Two 45° turns within the duct
A
length should be treated as a 90° elbow. A turn over 45° should be
treated as a 90° elbow.
Dryer exhausting information—use metal
duct only vertical and horizontal ducting
Best performance
Maximum length
of 4" dia rigid
A 4
metal duct
B
Exhaust hood type
A
A
B
Number
4
2-1/2
4"
2-1/2"
of 90°
B
turns opening opening
Domestic dryer models
0
120 ft.
90 ft.
2-1/2
1
100 ft.
75 ft.
2
85 ft.
65 ft.
3
70 ft.
55 ft.
Long Vent 6.0 - 8.0 cu. ft.
4
60 ft.
45 ft.
capacity electric & gas dryers
(HTX21 and HTX24)
5
55 ft.
35 ft.
A
For every extra 90° elbow, reduce the allowable vent system length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
When calculating the total vent system length, you must add all the straight
portions and elbows of the system (including the transition duct).
Laundry Center length includes factory-installed elbow that does not impact
vent length.
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney,
under any enclosed house floor (crawl space), or into an attic, since the
accumulated lint could create a fire hazard or moisture could cause
damage. Never terminate the exhaust into a common duct or plenum with
a kitchen exhaust, since the combination of lint and grease could create a
fire hazard. Exhaust ducts should be terminated in a dampered wall cap
to prevent back drafts, bird nesting, etc. The wall cap must also be located
at least 12" above the ground or any other obstruction with the opening
pointed down.
Specification Revised 5/16
HTX24GASKWS
Hotpoint® 6.2 cu. ft. capacity aluminized alloy gas dryer
FEATURES AND BENEFITS
Auto Dry - For clothes that come out feeling and looking great, this setting monitors
air temperature to set the optimal drying time
Up to 120 ft. venting capability - Provides flexible installation
Cottons
Cool Down
Less Dry
Optimum Dry
More Dry
Off
Casuals
More Dry
Less Dry
Cool Down
Off
Off
Quick Fluff 10
Aluminized alloy drum - Improves energy efficiency and resists corrosion
Temperature
Cottons
Regular
Casuals
Medium
Delicates
Low
Start
Push to Start
More Dry
Less Dry
20
Cool Down
30
Off Delicates
40
50
Time Dry
60
70
80 Min.
End of Cycle Signal
3 heat selections - Offer a choice of drying temperatures for personalized fabric care
Delicate cycle - Helps protect delicate fabrics
Rotary electromechanical controls - Make it simple to set cycles
Upfront lint filter - Makes cleaning out lint easy
End-of-cycle signal - Alerts you when the load is done, so clothes can be removed
before wrinkles set in
Reverse-a-door - Door opening can be reversed to meet laundry room needs
Model HTX24GASKWS – White with gray backsplash
HTX24EASKWS_HTX24GASKWS
Specification Revised 5/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising