Frigidaire FFMO1611LS Wiring Diagram/Installation Instructions

Frigidaire FFMO1611LS Wiring Diagram/Installation Instructions
Installation Instructions
Installation
Built-in Trim Kit
Instructions
Model # FFMOTK27LW FFMOTK27LB FFMOTK27LS
FFMOTK30LW FFMOTK30LB FFMOTK30LS
BEFORE YOU BEGIN
•
•
Read these instructions completely and carefully.
IMPORTANT – Save these instructions
•
for local inspector's use.
•
IMPORTANT – Observe all governing
codes and coordinates.
•
•
•
•
Note to Installer – Be sure to leave
these instructions with the Consumer.
•
Note to Consumer – Keep these
instructions for future reference.
Skill level - Installation of this appliance
requires basic mechanical and electrical
skills
•
FOR YOUR SAFETY:
Proper installation is the responsibility of the
installer.
Product failure due to improper installation is
not covered under the Warranty.
Unplug the microwave oven before
attempting installation of this kit.
Because the kit includes metal parts, caution
should be used in handling and installation to
avoid the possibility of injury.
Do not remove permanently affixed labels,
warnings, or plates from the product. This
may void the warranty.
IMPORTANT - PLEASE READ
AND FOLLOW
WARNING – Before beginning the installation,
switch power off at service panel and lock the
service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag, to
the service panel.
THIS BUILT-IN KIT IS DESIGNED FOR USE
ONLY WITH ELECTROLUX MICROWAVE
OVENS SPECIFYING BUILT-IN KIT
FFMOTK27LW/B/S OR
FFMOTK30LW/B/S ON THE RATING LABEL ON THE
LEFT SIDE WALL OF THE MICROWAVE OVEN
CAVITY.
QUESTIONS?
For customers in the United States call:1-1800-944-9044
For customers in Canada call: 1-800-265-8352 (English)
1-800-668-4606 ext.8199 (French)
Visit our Website at: www.frigidaire.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
PN: 316910002
October 2010
1
Installation Instructions
PARTS INCLUDED IN THE KIT
1. Front Frame Assembly- QTY 1
2. Exhaust Duct - QTY 1
3. Bottom Mounting Rail– QTY 2
3. Screw A - QTY 11
4. Screw B - QTY 4
CHOOSING A LOCATION FOR
YOUR MICROWAVE OVEN IF
BUILT-IN
Built-In Trim Kit allows for the installation of microwaves
listed below to be built into a cabinet or wall by itself or
over an electric wall oven*.
Front Frame Assembly
Microwave Models:
FFMO1611LW, FFMO1611LB, FFMO1611LS
See Illustration 1 for proper location and when building
in above a wall oven. Carefully follow both the wall oven
installation instructions and Electrolux’s Built-in Kit
instructions. If building over a wall oven, be sure the
clearance between the wall oven and the microwave
oven is a minimum of 3 inches.
*NOTE:
Illustration 1
Trim Kit Overall Dimensions
27”
Height 18 1/8(460mm)
Width 26 15/16(684mm)
Depth 1 1/16(26.8mm)
Trim Kit and microwave can only be built-in
over an electric self-clean or non self-clean
single cavity wall oven.
CABINET OR WALL CUTOUT
Cutout Dimensions
Height (A)
Minimum
Maximum
17” (432 mm)
171/4”(438 mm)
Width (B)
Minimum
Maximum
24 3/4” (629 mm)
25” (635 mm)
Depth (C)
Minimum
20” (508 mm)
Bottom Mounting Rail
Exhaust Duct
2
30”
18 1/8(460mm)
29 15/16(760mm)
1 1/16(26.8mm)
Installation Instructions
Screw A
Center Line
Illustration 2
Illustration 3
ELECTRICAL OUTLET LOCATION
EXHAUST DUCT ASSEMBLY
Outlet should NOT be in the shaded area as indicated
on Illustration 2
1. Draw a Central Line on floor. Place the Exhaust
Duct in the opening,When the Exhaust Duct
Assembly is in the opening correctly, the Center
Line is in the middle of the Exhaust Duct
Assembly. See Illustration 3.
2. Secure the Exhaust Duct Assembly with the
three screws A.
NOTE 1:
The floor of the opening should be constructed of
plywood strong enough to support the weight of the
oven and floor load (approximately 100 pounds). The
floor should be level for proper operation of the oven. Be
sure to check the local building code as it may require
that the opening be enclosed with side, ceiling and rear
partition. The proper functioning of the oven does not
require the enclosure.
IMPORTANT: Secure screws in outer hole.
3 units are needed for exhaust duct assembly
3
Installation Instructions
Bottom Mounting Rail
OVEN INSTALLATION
1. Turn microwave wave upside down so you are
looking at oven bottom. Secure the bottom
Mounting Rail on oven with four SCREWS A.
See Illustration 4 below.
2. Secure the Exhaust Duct Assembly with the four
screws A.--Place the bracket on proper location
where hole to hole with the oven, then put the
screw inside, and screw them up.
1. Place the oven adjacent to the wall or cabinet
opening. Plug the power cord into the electrical
outlet.
2. Carefully guide the assembled oven into the
prepared opening. Slide the oven on the
Exhaust Duct Assembly. See Illustration 5.
3. Secure the Exhaust Duct Assembly with the four
screws A.
Screw A
Guide line
B
Guide line
Screw A
A
Illustration 5
Illustration 4
Detail B
Detail A
FRAME INSTALLATION
4
Installation Instructions
1.
2.
Position the FRAME ASSEMBLY to be square
with the oven. Carefully place the FRAME
ASSEMBLY on the oven. See Illustration 6.
Check that it is level and then secure with two
SCREWS B. Secure the bottom portion of the
FRAME ASSEMBLY with the two remaining
SCREWS B. See Illustration 7.
Illustration 6
Illustration 7
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement