Wolf | PW302418 | In Line Blowers Installation | Wolf PW302418 In Line Blowers Installation

MODEL 808331
Page 1
IN-LINE BLOWER
READ AND SAVE THESE INSTRUCTIONS
!
FOR DOMESTIC COOKING ONLY
!
WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer or your distributor.
2. Before servicing or cleaning unit, switch power off at service panel
and lock the service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s
guideline and safety standards such as those published by the
National Fire Protection Association (NFPA), and the American
Society for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. To reduce the risk of fire, use only steel ductwork.
8. If this unit is to be installed over a tub or shower, it must be marked
as appropriate for the application and be connected to a GFCI
(Ground Fault Interrupter) - protected branch circuit.
9. Never place a switch where it can be reached from a tub or
shower.
10. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef
Flambe’).
3. Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the
size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT
OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately, EVACUATE AND
CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - violent
steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you already
know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
CAUTION
!
1. For general ventilating use only. Do not use to exhaust hazardous
or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
3. If ventilator is installed in an unconditioned space (such
as an attic): Surround the ventilator with thermal insulation - to
minimize possible condensation.
4. Please read specification label on product for further information
and requirements.
TABLE OF CONTENTS
This manual is divided into sections as follows:
 “TYPICAL INSTALLATION”
This section shows a common installation.
- Mounting (New Frame Construction)
- Mounting (Existing Frame Construction)
- Mounting Using Hanger Kit (included)
- Ducting (Horizontal blower discharge)
- Wiring
 “MOUNTING OPTIONS”
 “WIRING PLATE POSITION”
 “DUCTING OPTIONS”
- Blower Discharge Positions
- Ducting (Vertical blower discharge)
 “ATTACH POWER CORD TO HOOD”
 “USE AND CARE”
Installer: Leave this manual with
the homeowner.
Homeowner: Use and Care
information on page 4.
Page 2
TYPICAL INSTALLATION
TYPICAL INSTALLATION
MOUNTING (New Frame Construction)
MOUNTING USING HANGER KIT (included)
10” ROUND DUCT
4½” X 18½”
TO 10” ROUND
TRANSITION
Mounting brackets
factory-shipped in
position for ½” ceiling material.
CEILING
JOIST
(24” centers
shown)
HANGER
KIT BOLT
& WASHER
EXTENSION
SPRING
HANGER
KIT CHAIN
10” ROUND
DUCT (INTAKE)
HANGER
KIT
EYE-BOLT
10” ROUND
DUCT
Blower factory-shipped
in horizontal
discharge position.
4½” X 18½”
TO 10”
ROUND
TRANSITION
4½” X 18½”
TO 10” ROUND
TRANSITION
MOUNTING
SCREW
Factory-shipped unit installed in new construction.
MOUNTING
BRACKET
4½” X 18½” TO 10”
ROUND TRANSITION
4½” X 18½”
TO 10” ROUND
TRANSITION
10” ROUND
DUCT
GRILLE NUT
(Install into
square holes in
housing)
10” ROUND
DUCT
(OUTLET)
MOUNTING (Existing Frame Construction)
2 X 4 FRAMING
(wide side down)
HANGER
KIT NUT &
WASHER
Blower factory-shipped in straight-through
discharge position.
DUCTING (Horizontal blower discharge)
10” ROUND
DUCT
ROOF CAP
10”
ROUND
DUCT
4½” X 18½”
TO 10” ROUND
TRANSITION
MOUNTING
SCREW
MOUNTING
BRACKETS
(Attached to
opposite sides
of housing &
upside-down,
so housing is
flush with
finished ceiling)
ACCESS
PANEL SCREW
ACCESS
PANEL
CEILING JOIST
(24” centers
shown)
Blower factory-shipped in straight-through
discharge position.
10”
ROUND
DUCT
10”
ROUND
ELBOW
WALL
CAP
Two ways to connect ductwork to a factory-shipped unit.
IMPORTANT: Remove shipping tape from damper
Remove the shipping tape from the damper flap and make sure that
damper flap opens and closes freely inside the ductwork. Use duct
tape to make ductwork connections secure and air-tight.
Page 3
WIRING PLATE POSITION
WIRING
BLACK
TO
BLACK
TOP / BACK
OF HOUSING
VERTICAL
POWER CABLE
CONNECTION
GROUND TO
WIRING PLATE
WIRING
PLATE
HORIZONTAL POWER
CABLE CONNECTION
120 VAC
LINE IN
(from
range
hood)
WHITE
TO
WHITE
Ventilator can be wired from outside of housing.
Use UL approved connectors to wire per local codes.
MOUNTING OPTIONS
Wiring plate mounts to side or top of housing.
DUCTING OPTIONS
BLOWER DISCHARGE POSITIONS
¼-20 hex nuts secure mounting brackets to housing. Loosen and
re-tighten or remove and replace nuts as necessary for desired
mounting bracket position.
DUCT CONNECTOR
1½"
to
2½"
11/ 8"
MAX.
21½"
DUCT CONNECTOR
Change
blower
& duct
connector
positions
for vertical
discharge.
21½"
INSTALLATION
FROM ABOVE FINISHED CEILING
ADUSTABLE FOR VARIOUS CEILING
THICKNESSES
Mounting brackets in
factory-shipped position.
(Outlet parallel to joists.)
(New construction)
Mounting brackets flipped
over and mounted to outlet
sides of housing.
(Outlet parallel to joists.)
(Existing construction)
11/ 2"
to
21/ 2"
BLOWER
BLOWER
Blower and duct connector in horizontal discharge
position. (Factory shipped)
Blower and duct connector in vertical discharge
position.
12¼"
21½"
INSTALLATION WITH DUCTWORK
RUNNINGbrackets
ACROSS mounted
JOISTS
ADUSTABLE Mounting
FOR VARIOUS
CEILING
THICKNESSES
Mounting
brackets
flipped
to outlet sides of housing.
(Outlet perpendicular to joists.)
(New construction)
over to give approx. 1”
more clearance.
(Outlet parallel to joists.)
(New construction)
10 3/ 4" to
11 3/ 4"
91/ 2" to
101/ 2"
21½"
DUCTING (Vertical blower discharge)
ROOF CAP
10”
ROUND
DUCT
4½” X 18½”
TO 10” ROUND
TRANSITION
21½"
ADUSTABLE
FOR VARIOUS
CEILING
THICKNESSES
ADUSTABLE
FOR VARIOUS
Mounting
bracketsCEILING
flippedTHICKNESSES
Mounting
brackets
mounted
to top of sides of housing.
(Outlet parallel to joists.)
(New or existing construction)
over and mounted to top of
sides of housing.
(Outlet parallel to joists.)
(New or existing construction)
Typical ductwork connection to a ventilator converted to
vertical discharge.
Page 4
ATTACH POWER CORD TO
HOOD
Follow wiring instructions packed with range hood, and adhere to
all local and state codes, and the National Electrical Code.
WARNING: To reduce the risk of electric shock,
disconnect from power supply before servicing.
USE AND CARE
To clean blower assembly: Remove access panel, unplug blower
from housing, remove blower mounting nuts, and carefully remove
blower from housing. Use appropriate vacuum attachment or a soft
cloth and mild soap or detergent to clean blower discharge area and
wheel. DO NOT ALLOW WATER TO ENTER MOTOR. Make sure
blower assembly is completely dry before reinstalling.
Motor is permanently lubricated. Do not oil or disassemble motor.
Some hoods require the use of a separate power cord and strain
relief bushing (included), for proper wiring of in-line blowers. Please
refer to the hood manual for proper installation instructions.
99043889B
MODEL 808332
Page 1
IN-LINE BLOWER
READ AND SAVE THESE INSTRUCTIONS
!
FOR DOMESTIC COOKING ONLY
!
WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer or your distributor.
2. Before servicing or cleaning unit, switch power off at service panel
and lock the service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s
guideline and safety standards such as those published by the
National Fire Protection Association (NFPA), and the American
Society for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. To reduce the risk of fire, use only steel ductwork.
8. If this unit is to be installed over a tub or shower, it must be marked
as appropriate for the application and be connected to a GFCI
(Ground Fault Interrupter) - protected branch circuit.
9. Never place a switch where it can be reached from a tub or
shower.
10. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef
Flambe’).
3. Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the
size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT
OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately, EVACUATE AND
CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - violent
steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you already
know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
CAUTION
!
1. For general ventilating use only. Do not use to exhaust hazardous
or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
3. If ventilator is installed in an unconditioned space (such
as an attic): Surround the ventilator with thermal insulation - to
minimize possible condensation.
4. Please read specification label on product for further information
and requirements.
TABLE OF CONTENTS
This manual is divided into sections as follows:
 “TYPICAL INSTALLATION”
This section shows a common installation.
- Mounting (New Frame Construction)
- Mounting (Existing Frame Construction)
- Mounting Using Hanger Kit (included)
- Ducting (Horizontal blower discharge)
- Wiring
 “MOUNTING OPTIONS”
 “WIRING PLATE POSITION”
 “DUCTING OPTIONS”
- Blower Discharge Positions
- Ducting (Vertical blower discharge)
 “ATTACH POWER CORD TO HOOD”
 “USE AND CARE”
Installer: Leave this manual with
the homeowner.
Homeowner: Use and Care
information on page 4.
Page 2
TYPICAL INSTALLATION
TYPICAL INSTALLATION
MOUNTING (New Frame Construction)
MOUNTING USING HANGER KIT (included)
10” ROUND DUCT
(OUTLET)
8” X 12” TO
10” ROUND
TRANSITION
(MALE)
8” X 12” TO
10” ROUND
TRANSITION
(FEMALE)
10” ROUND
DUCT
(INTAKE)
MOUNTING
BRACKETS
Ventilator
factory-shipped
in straight-through
discharge position.
EXTENSION
SPRING
HANGER
KIT CHAIN
8” X 12” TO
10” ROUND
TRANSITION
(MALE)
HANGER
KIT NUT &
WASHER
MOUNTING
BRACKET
GRILLE NUT
(Install into
square holes in
housing)
ACCESS PANEL
10” ROUND
DUCT
(OUTLET)
MOUNTING (Existing Frame Construction)
8” X 12” TO
10” ROUND
TRANSITION
(MALE)
10” ROUND
DUCT (INTAKE)
CEILING
JOIST
(24” centers
shown)
Factory-shipped unit installed in new construction.
8” X 12” TO 10” ROUND
TRANSITION (FEMALE)
HANGER
KIT BOLT
& WASHER
HANGER KIT
EYE-BOLT
GRILLE NUT
(Install into square
holes in housing)
ACCESS
PANEL
SCREW
8” X 12” TO
10” ROUND
TRANSITION
(FEMALE)
10” ROUND
DUCT (INTAKE)
Blower factory-shipped in straight-through
discharge position.
MOUNTING
BRACKETS
DUCTING (Horizontal blower discharge)
10” ROUND
DUCT
(OUTLET)
ROOF CAP
MOUNTING
SCREWS
CEILING
JOIST
(24” centers
shown)
Ventilator factory-shipped
ACCESS
in straight-through
PANEL SCREW
discharge position.
ACCESS
PANEL SCREW
ACCESS
PANEL
GRILLE NUT
(Install into
square
holes in housing)
10”
ROUND
DUCT
8” X 12” TO
10” ROUND
TRANSITION
(MALE)
10”
ROUND
DUCT
ACCESS
PANEL
Factory-shipped unit installed in existing construction.
8” X 12” TO 10” ROUND
TRANSITION (FEMALE)
10” ROUND
ELBOW
WALL
CAP
Two ways to connect ductwork to a factory-shipped unit.
IMPORTANT: Remove shipping tape from damper
Remove the shipping tape from the damper flap and make sure that
damper flap opens and closes freely inside the ductwork. Use duct
tape to make ductwork connections secure and air-tight.
Page 3
WIRING
WIRING PLATE POSITION
BLACK
TO
BLACK
EDGE
OF HOUSING
GROUND TO
WIRING PLATE
VERTICAL
POWER CABLE
CONNECTION
WIRING
PLATE
HORIZONTAL POWER
CABLE CONNECTION
WHITE
TO
WHITE
Wiring plate mounts to side or top of housing.
120 VAC LINE IN
(from range hood)
DUCTING OPTIONS
Ventilator can be wired from outside of housing.
Use UL approved connectors to wire per local codes.
BLOWER DISCHARGE POSITIONS
MOVABLE
PANEL
MOUNTING OPTIONS
¼-20 hex nuts secure mounting brackets to housing. Loosen and
re-tighten or remove and replace nuts as necessary for desired
mounting bracket position.
Factory-Shipped
Straight-Through
Discharge
11/ 8"
MAX.
Factory-Shipped
Straight-Through
Discharge
22"
1½"
to
2½"
18"
ADUSTABLE
FOR VARIOUS
CEILING
Mounting
Mounting
brackets
in THICKNESSES
factory-shipped position mounted directly to joists.
(Outlet parallel to joists.)
(New construction)
brackets flipped
over and mounted to additional framing.
DUCT
DUCT
Housing
CONNECTOR rotated & mov- CONNECTOR
(outlet)
(outlet)
able panel covers previous
open side.
DUCT
CONNECTOR
(intake)
Ventilator shown in
straight-through discharge
position. (Factory shipped)
(Outlet perpendicular to joists.)
(New or Existing construction)
MOVABLE
PANEL
(Change to this
DUCT
location)
CONNECTOR
(intake)
Ventilator shown in rightangle discharge position.
(Change movable panel to
new location as shown.)
DUCTING (Vertical blower discharge)
Housing Converted to RightAngle Discharge
18"
1½"
to
2½"
Factory-Shipped
Straight-Through
Discharge
22"
8” X 12” TO
10” ROUND
TRANSITION
(MALE)
8” X 12” TO 10”
ROUND
TRANSITION
(FEMALE)
ROOF CAP
10” ROUND
DUCT
FOR brackets
VARIOUS CEILING
Mounting
flipped THICKNESSES
Mounting brackets flippedADUSTABLE
10” ROUND
over and mounted to top of
over and mounted to adDUCT
housing. Housing secured
ditional framing.
(Outlet vertical.)
with cables.
(New or Existing construction)
Typical ductwork connection to a ventilator converted to
(Outlet parallel to joists.)
(New or Existing construction)
right-angle discharge.
Page 4
ATTACH POWER CORD TO
HOOD
Follow wiring instructions packed with range hood, and adhere to
all local and state codes, and the National Electrical Code.
WARNING: To reduce the risk of electric shock,
disconnect from power supply before servicing.
USE AND CARE
To clean blower assembly: Remove access panel, unplug blower
from housing, remove blower mounting nuts, and carefully remove
blower from housing. Use appropriate vacuum attachment or a soft
cloth and mild soap or detergent to clean blower discharge area and
wheel. DO NOT ALLOW WATER TO ENTER MOTOR. Make sure
blower assembly is completely dry before reinstalling.
Motor is permanently lubricated. Do not oil or disassemble motor.
Some hoods require the use of a separate power cord and strain
relief bushing (included), for proper wiring of in-line blowers. Please
refer to the hood manual for proper installation instructions.
99043890C
Download PDF

advertising