Dacor | HCT365GSNG | Planning Guide | Dacor HCT365GSNG Planning Guide

RNCT305G, RNCT365G
Revised 0706/16 Page 1/4
Document # PG04-011
Renaissance®
PLANNING
GUIDE
30” and 36” Wide
Drop-in Gas Cooktops
WARNING
•
Observe all governing codes and ordinances during planning
and installation.
•
Contact your local building department for further information.
•
This appliance must be installed in accordance with the
accompanying installation instructions.
Product tolerances ±1/16” (±1.6 mm) unless otherwise
A
2" (5.1 cm)
from countertop
to cooking surface
4" (10.2 cm)
chassis height
Model
A
B
RNCT305G
30” (76.2 cm)
27 5/16” (69.4 cm)
RNCT365G
36” (91.4 cm)
33 5/16” (84.6 cm)
Rear
overhang
1 3/16”
(3.0 cm)
Front
overhang
17/32”
(1.3 cm)
21"
(53.3 cm)
1 11/32”
(3.4 cm)
1 11/32”
(3.4 cm)
19 9/32” (49.0 cm)
B
Side View
Front View
Product Dimensions
Front of cooktop
Front of unit
Power
cord
1/2” male NPT
gas inlet*
1 3/4”
(4.4 cm)
1/2” male
NPT gas inlet
Power cord
42” (106.7 cm) long
Chassis
1 3/4”
(4.4 cm)
2”
(5.1 cm)
Top panel overhang
*Gas inlet extends 1” (2.5 cm) from bottom
UTILITY LOCATIONS
All specifications subject to change without notice.
UTILITY DIMENSIONS
www.dacor.com
Phone: (800) 793-0093
4.18
RNCT305G, RNCT365G
Revised 07/06/16 Page 2/4
Document # PG04-011
PLANNING
GUIDE
Renaissance® 30” and 36” Wide,
Drop-in Gas Cooktops
Electrical Requirements
Gas Supply Requirements
WARNING
To prevent an electric shock hazard, the power supply must meet
the specifications stated below. It is the owner’s responsibility
to make sure that the electrical service meets electrical requirements and that the electrical outlet has been properly installed by
a licensed electrician.
◊
◊
The cooktop is supplied with a factory installed, 42 inch power cord
with a, three-prong, grounding electrical plug. It is connected to
the chassis at the bottom right rear corner (see Chassis Bottom
Diagram below). It must be connected to a dedicated, grounded
three-prong electrical outlet installed by a licensed electrician.
The electrical installation, including minimum supply wire size and
grounding, must be done in accordance with National Electric Code
ANSI/NFPA 70* and local codes and ordinances. A copy of this
standard may be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
◊
◊
The correct voltage, frequency and amperage must be supplied to
the electrical outlet according to the product data label located on the
bottom of the chassis. See the Gas and Electrical Requirements table
on this page for reference.
Be certain to locate the electrical outlet so that the power may be
easily disconnected if the unit needs service.
Front of unit
Product data label
◊
Be certain that the cooktop being installed is correct for the gas
service being provided (natural gas or LP gas). Also, if operating
the cooktop at an altitude above 4000 ft. (1219 m) make sure it is
equipped for high altitude operation.
◊
Units equipped for LP operation have “LP” in the model number listed
on the product data label. See the Chassis Bottom Diagram for label
location.
◊
Units equipped for high altitude operation have an “H” at the end of
the model number listed on the product data label.
◊
Check your local building codes for the proper method of installation.
In the absence of local codes, this appliance should be installed in
accordance with the National Fuel Gas Code ANSI Z223.1/NFPA 54.
◊
An external manual shut-off valve must be installed between the gas
inlet and the cooktop for the purpose of turning on or shutting off gas
to the appliance.
◊
The cooktop comes from the factory with a regulator in the shipping
carton. Use only the regulator provided. The regulator must be
installed in the gas line that runs from the cooktop gas inlet to the gas
shut off valve.
◊
The regulator inlet accommodates a 3/4” gas line. The inlet to the
cooktop itself is equipped with a 3/4” male NPT fitting.
The cooktop gas connection is located on the bottom of the cootktop in the
back right corner as you face the front of the unit. See the Chassis Bottom
Diagram on this page.
RNCT305G_NG
RNCT365G_NG
RNCT305G_LP
RNCT365G_LP
Gas type
Natural Gas
LP Gas
Manifold
pressure
5” water column
10” water column
Min. gas supply
Pressure**
6” water column
11” water column
Max. gas supply
pressure
1/2 psi
1/2 psi
0.25 Amp.
(30 Watts)
0.25 Amp.
(30 Watts)
120 Vac,
60 Hz, 15 Amp.
120 Vac,
60 Hz, 15 Amp.
Total connected load
Circuit requirement
CHASSIS BOTTOM DIAGRAM
GAS AND ELECTRICAL REQUIREMENTS*
* The electrical and gas data on this page is for reference only. If the
above data does not agree with the product data label, use the data on the
product data label.
** The gas supply pressure for testing the regulator setting shall be at least
1 inch water column (249 Pa) above the specified manifold pressure.
All specifications subject to change without notice.
www.dacor.com
Phone: (800) 793-0093
4.19
RNCT305G, RNCT365G
Revised 07/06/16 Page 3/4
Document # PG04-011
Renaissance® 30” and 36” Wide
Drop-in Gas Cooktops
Cabinet and Countertop Layout
◊
WARNING
•
To reduce the risk of personal injury caused by reaching over
a hot appliance, avoid locating cabinet storage space directly
above the cooktop.
•
Failure to meet or exceed the maximum and minimum
dimensions/clearances stated in these instructions may result
in a fire hazard.
•
Follow the countertop manufacturer’s instructions regarding
the minimum corner radius, use of heat reflective tape,
reinforcement of corners, etc.
◊
Allow a minimum 1/4” (6 mm) clearance between the bottom of the
cooktop chassis and all combustible surfaces, including the upper
edge of a drawer installed below the cooktop.
This appliance is to be used in conjunction with a suitable vent hood
or approved Dacor downdraft vent system.
* Allows for clearance between hold down brackets
Model
◊
Cabinet tolerances: +1/16” (+1.6 mm), -0,
unless otherwise stated
B Minimum
RNCT305G
29 1/4” (74.3 cm)
RNCT365G
35 1/4” (89.5 cm)
The gas supply piping, gas shut-off valve and the electrical outlet
must be located so they do not interfere with the cooktop when it is
installed. If installing another appliance in the cabinet below, allow for
the routing of gas and electrical service behind it.
The installation must allow for the following:
A
13” max.3
(33.0 cm)
18” min.1, 3
(45.7 cm)
Combustible
surface to rear
1/4” (6 mm)
mimimum clearance
to combustible
surfaces
B
Carefully check the location where the cooktop will be installed. For
best performance, the cooktop should be placed away from drafts that
may be caused by doors, windows and heating and air conditioning
outlets.
◊
PLANNING
GUIDE
◊
Access to the gas shut-off valve and regulator when the unit is
installed.
◊
Access to the electrical outlet when the cooktop is in place. The 42”
(106.7 cm) power cord must be able to reach the electrical outlet
◊
Access to the underside of the cooktop for service and inspection
purposes
◊
Clearance inside the cabinet to allow for proper hold down bracket
installation.
To allow access to the utilities and cooktop bottom, a fixed shelf should
not be installed below the cooktop. See the following pages for countertop
cutout dimensions.
30” min.1, 2
(76.2 cm)
See cutout
dimensions
1 5/8” min.
(4.1 cm)
See cutout
dimensions
1
Distance to combustible surfaces measured from cooking
surface (top of cooktop grate).
2
If installing with an overhead range hood, check the hood
specifications for minimum required clearances.
3
This specification does not apply for cabinets located
greater than a horizontal distance of 5 1/2” (14.0 cm) from
edge of cooktop. Allow 6 7/8” (17.5 cm) from cutout edge.
MINIMUM REQUIRED CLEARANCES AROUND THE COOKTOP
Model
(A) Minimum
(A) Recommended
RNCT305G
30” (76.2 cm)
36” (91.4 cm)
RNCT365G
36” (91.4 cm)
42” (106.7 cm)
All specifications subject to change without notice.
www.dacor.com
Phone: (800) 793-0093
4.20
RNCT305G, RNCT365G
Revised 07/06/16 Page 4/4
Document # PG04-011
Renaissance®
30” and 36” Wide
Drop-in Gas Cooktops
PLANNING
GUIDE
Cutout Dimensions
Cabinet tolerances: +1/16” (+1.6 mm), -0, unless otherwise stated
Downdraft Compatibility
IMPORTANT: If installing cooktop with a
downdraft, install only the Dacor downdraft models
specified in the table below.
Rear
wall
Vertical
combustible
surface
4 1/4” (10.8 cm) min.
from mounting surface to
combustibles below
cooktop chassis
C
F
E
D
F
Minimum distance to combustible side
wall above countertop (both sides)
1 5/8” min.
(4.1 cm)
Configuration
RNCT305G with no downdraft
RNCT305G with ERV3015 downdraft
RNCT365G with no downdraft
RNCT365G with ERV3615 downdraft
C (Minimum)
D
E
3 1/4” (8.3 cm)
19 5/8” (49.9 cm)
3/8” (1.0 cm)
22 3/4” (57.8 cm)
3 1/4” (8.3 cm)
19 5/8” (49.9 cm)
3/8” (1.0 cm)
22 3/4” (57.8 cm)
F (Minimum)
27 5/8” (70.2 cm)
6 7/8” (17.5 cm)
33 5/8” (85.4 cm)
For replacement purposes, a RNCT series cooktop will fit into the cutout of a Dacor SGM series cooktop.
3/8” min. (1.0 cm)
flat countertop overhang
required behind cutout
Stiffener
Countertop
RNCTXXXG
Series
Cooktop
DCT Series
cooktop
Cabinet face
3/8” min. (1.0 cm) space
behind downdraft vent
chassis to clear stiffener
ERVxx15 downdraft vent.
Check downdraft vent
dimensions/specifications
to determine proper fit
Floor
SIDE VIEW - RNCT SERIES COOKTOP WITH DACOR DOWNDRAFT
All specifications subject to change without notice.
www.dacor.com
Phone: (800) 793-0093
4.21
Download PDF

advertising