Broan | RMDD3004EX | Specification Sheet | Broan RMDD3004EX Specification Sheet

Broan RMDD3004EX Specification Sheet
SPECIFICATION SHEET
MODELS RMDD3004EX,
RMDD3604EX, RMDD4804EX
DOWNDRAFT
For use with external blowers.
Exhaust your cooktop without the use of an overhead hood. Control a powerful external blower from
the cooktop location. Compact design is installed
directly behind cooktop.
TYPICAL SPECIFICATION
FEATURES
Unit to have steel housing with silver paint finish. Air vent to
rise at least 9½" and have a stainless steel front and back
for ease of cleaning.
HOUSING:
• Rugged steel construction
• Finished with silver paint
• Space-saving - can be used with most cooktops on the
market
• 30", 36", or 48" widths - Fits standard-size cabinets
CHIMNEY ASSEMBLY:
• Brushed stainless steel cover - just press button to turn
•
•
•
•
•
•
•
unit "ON"
Chimney rises 9½" when activated - ideal for large pots
and pans
Stylish, stainless steel filters with aluminum mesh - easy
to remove and dishwasher-safe
Stainless steel chimney front and back - makes cleanup
quick and easy
Flush-mounted, infinite rotary speed blower control
Heat Sentry adjusts speed of blower to HIGH in case of
excess heat
Conveniently located button - press to lower air vent and
turn unit "OFF"
OPTIONAL Remote Control (Model RMDDRBK) activates
downdraft from alternate location
Downdraft blower system shall be Broan Elite Model RMDD3004EX (RMDD3604EX) (RMDD4804EX).
Unit shall be for indoor use only.
Filters to be stainless steel with aluminum mesh, easy to
remove and dishwasher-safe.
3¼" x 14" duct connector shall be adjustable to accomodate
ductwork from left, right, or below and have 7½" side to side
adjustment.
Unit must accept an optional remote control activation button.
Unit to include Heat Sentry, to adjust blower speed to HIGH
in case of excess heat.
Downdraft system shall operate on 120 VAC and be able to
be plugged into a standard grounded outlet. It will have an
infinite speed blower control.
SPECIFICATIONS
VOLTS
HZ
AMPS
DUCT
120
60
6
3¼" x 14"
DUCT CONNECTOR HOUSING:
• Rugged steel construction with galvanized finish
• 3¼" x 14" rectangular duct connector (8" round duct using
Model 459 transition)
• 3-position discharge - movable to adjust to floor joists
Broan-NuTone LLC Hartford, Wisconsin www.broan.com 800-558-1711
Broan-NuTone Canada, Inc. Mississauga, Ontario www.broan.ca 877-896-1119
REFERENCE
QTY.
REMARKS
Project
Location
Architect
Engineer
Contractor
Submitted by
Date
90M
99043190C
INSTALLATION PLANNING • MODELS RMDD3004EX, RMDD3604EX, RMDD4804EX
DIMENSIONS
DOWNDRAFT
A
NOTE: Dimensions shown are for reference only. Before cutting out
countertop, refer to instructions packed with downdraft and cooktop.
1 3/4 "
2"
COUNTER TOP
COOKTOP
B
DOWNDRAFT
*
FRONT TO BACK
INSIDE CABINET DEPTH
*
Refer to the cooktop installation instructions for dimensions of
cooktop, countertop cut-out, and cabinet requirements. The
RMDD3004EX can be installed in most standard 30" wide cabinets, (RMDD3604EX can be installed in most standard 36" wide
cabinets), (RMDD4804EX can be installed in most standard 48"
wide cabinets).
Cooktop depth can vary greatly from one to another. This may
cause the fit of these two appliances to be rather tight.
from top
* Dimensioned
of countertop
CHIMNEY TOP
GEAR
MOTOR
COVER
CABINET
FRONT
DUCTWORK
This downdraft blower system is designed for use with 3¼" x 14"
rectangular ductwork (can be transitioned to 8" or 10" round). The
blower discharge can be positioned in one of 3 directions with
7½" movement side to side.
TYPICAL INSTALLATION
COUNTER
TOP
COOK TOP
Pay special attention to the 4 areas of potential interference
highlighted above. A countertop with (A) a raised lip and/or (B)
a backsplash, may not allow enough flat countertop for a proper
installation. The back of the downdraft cut-out will be 1¾" from
the cooktop and 2" of FLAT countertop is needed behind cooktop.
RIGHT
DISCHARGE
AIR
VENT
LEFT
DISCHARGE
BLOWER
BOX
120 VAC
GOUNDED
OUTLET
3-1/4" X 14"
DUCT CONNECTOR
ELECTRICAL
The unit has an 18-in. power cord with a 3-pronged plug. Plan to
provide a grounded outlet within reach of this cord.
DOWN
DISCHARGE
(as shipped)
3¼" x 14" TO
8" RD.
TRANSITION
8" RD.
ELBOW
3¼" X 14"
90o ELBOW
5 FT.
19 FT.
11 FT.
The system will operate most efficiently when the ductwork does
not exceed 40 feet of equivalent duct. The chart above, shows
equivalent feet of elbows and transitions. The number of feet of
straight 3¼" x 14" or 8" duct plus the equivalent feet of elbows or
transitions to be used should equal 40 feet or less.
The equivalent feet of various roof and wall caps has been taken
into consideration. Do not include them in this calculation.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising