Verona | VEHOOD3610 | Instalation Manual | Verona VEHOOD3610 Instalation Manual

User’s Manual
Under Cabinet Series
VEHOOD3610
NOTE: PLEASE INSPECT HOOD
IMMEDIATELY UPON RECEIVING.
CLAIM OF DAMAGE AFTER 7 DAYS
OF DELIVERY WILL BE DENIED.
This unit is designed for indoor
residential use only. DO NOT USE
OVER A WOOD GRILL OR MOUNT
IN OUTDOOR ENVIRONMENT.
Please read this manual thoroughly before installing
your range hood. Store it in a safe location for when
you need to reference it in the future.
TABLE OF CONTENTS
1
SAFETY INFORMATION ........................................................................ 2-3
CONTENT CHECKLIST ............................................................................. 4
MEASUREMENTS .................................................................................. 5
PREPARATION ............................................................................... 6 – 7
INSTALLATION ................................................................................ 8 – 9
RE-CIRCULATING KIT (OPTION) INSTALLATION .......................................... 10
OPERATION & FEATURES ..................................................................... 11
CLEANING & MAINTENANCE ................................................................. 12
TROUBLESHOOTING ............................................................................ 13
PARTS LIST / REPLACEMENT ................................................................. 14
WIRING DIAGRAM ............................................................................. 15
WARRANTY / CONTACT US ............................................................. 16-17
Verona Hood VEHOOD3610 can be installed using
outside venting or by use of a re-circulating kit.
HOOD SPECIFICATIONS




36” W x 10” H x 22” D
600 CFM
Hood construction - 430 Stainless Steel
120V 60Hz 3.0 A
2
SAFETY INFORMATION
SAFETY INFORMATION
TO REDUCE THE RISK OF A FIRE, ELECTRICAL SHOCK,
AND/OR INJURY OBSERVE THE FOLLOWING:

Unit is intended for indoor residential use only. If you should have
questions, contact the manufacturer at the address or telephone number
listed in the warranty.

In case the unit should need to be cleaned or repaired, switch power off
at service panel and lock service disconnecting means to prevent power
from being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.

Installation work and electrical wiring must be done by a qualified
technician in accordance with all applicable codes and standards,
including fire-rated construction.

Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent back
drafting. Follow the heating equipment manufacturer’s guideline and
safety standards such as those published by the National Fire
Protection Association (NFPA), and the American Society of Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE), and the local
code authorities.

Because the unit is made of stainless steel, it may contain sharp edges.
Be careful to avoid cuts and abrasions by wearing protective gloves
during installation and cleaning.

Before you begin to cut or drill into the wall, verify that there is no
electrical wiring or any other hidden electrical components.

Ducted fans must always be vented to the outdoors.

The unit must be properly grounded and installed at the recommended
height before beginning operation.
To reduce the risk of fire, use only metal ductwork.

CAUTION: FOR GENERAL VENTILATING USE ONLY. DO
NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE
MATERIALS AND VAPORS
SAFETY INFORMATION
3
TO REDUCE THE RISK OF FIRE, OR ELECTRIC SHOCK, DO
NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL
DEVICE.

Regardless of heat level, never leave any surface materials unattended
while operating an open flame.

Always turn hood ON when cooking at high heat.

Depending on amount of usage, clean ventilating fans and filters
frequently. Grease should not be allowed to accumulate on fan or filter.
For instructions on the how to clean, see maintenance page.

Never leave surface units unattended at high settings. Boil-overs may
cause smoking and greasy spillovers may ignite as result. Heat oils
slowly on low or medium settings.

Use proper pan size. Always use cookware appropriate for the size of
the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING:




SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray,
then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the
flames do not go out immediately, EVACUATE AND CALL 911.
NEVER PICK UP A FLAMING PAN - Doing so may result in serious
burns and possibly spread the fire.
DO NOT USE WATER – Grease fire must be extinguished before
further action may be taken. Using water will agitate the grease and
may cause a violent steam explosion.
Use a Fire Extinguisher ONLY if:
 You know you have a Class ABC extinguisher, and you
already know how to operate it.
 The fire is small and contained in the area where it started.
 The fire department is being called.
 You are able to safely control the fire with your back to an open
exit. * Based on “Kitchen Fire safety Tips” published by NFPA.
4
CONTENT CHECKLIST
1. CONTENTS INCLUDED
a.
(1) VEHOOD3610 - 36” hood assembly
b.
(1) User’s manual
c.
(1) Black 6” collar & (1) 6” – 7” Transition
d.
(3) Mesh filters
e.
(1) Screw packet
2. CONTENTS NOT INCLUDED
a.
Recirculation Kit (Purchased separately)
b.
6” or 7” Metal ducting
3. TOOLS REQUIRED (NOT INCLUDED)
a.
Safety gloves
b.
Safety glasses
c.
Electric drill w/ starter bit
d.
Utility knife
e.
Spirit level
f.
Measuring tape
g.
Writing instrument (pen, marker, pencil)
h.
Aluminum or duct tape
i.
Wire nuts
Round metal duct,
length to suit
installation.
MEASUREMENTS
Fig. 1a
Centerline
5
Keyhole
2 ¼” from Rear
16 ⅝” from Center
10 ⅜” from Rear
Electrical Opening
1 ⅞” from Rear
13 ⅝” from Center
17 ⅞”
24”-36”
6
PREPARATION
1. BEFORE YOU START
**DO NOT INSTALL IF DAMAGED**
**RETURN OR EXCHANGE WILL BE DENIED IF INSTALLED**
a.
Confirm you have all parts and required tools for this installation.
b.
Installation may take at least 2 to 3 hours from start to finish.
c.
Minimize the number of duct elbows (turns) used to maximize hood
performance
d.
Duct elbows should be no closer than 12” to each other, further
apart if possible.
e.
At least two people are needed for installation.
f.
Hiring a certified installer and electrician is recommended.
g.
In some jurisdictions, make-up / replacement air is required.
Check with your local building codes for more details.
2. LOCATION
a.
Determine the exact location you want to install the range hood.
b.
A centerline should be located on bottom of cabinet or soffit.
c.
Distance between cooktop and range hood should be between
24”- 36”. (Fig. 1b)
d.
Range hood should be mounted at stated measurements to ensure
performance and lifespan of electrical components.
e.
For cabinets with recessed-bottom, securely fasten wood strips on
bottom sides of the cabinet so that it is level, and can receive and
support the screws which hold the hood.
7
PREPARATION
Use Fig. 1a and 1b on page 5 for measurements
Center Line
Electrical Opening
1 ⅞” from Rear
13 ⅜” from Centerline
Install wood strips to level if cabinet bottoms are recessed.
Cabinet opening for exhaust should be:

6½” diameter if using collar ONLY

8¼” diameter if using collar + 6” – 7” transition
Place hood under the cabinet to be installed and mark 4 keyholes
to drill starter hole.
8
INSTALLATION
1. UNDER CABINET OR SOFFIT INSTALLATION
a.
Make sure all preparation steps are completed.
b.
Connect 6” black collar to hood. (1) Using screws provided
c.
If using transition, connect transition with damper to 6” black collar,
wider part to front (2)
d.
Secure collar and transition with sheetmetal screws and/or duct
tape for an air-tight seal. Do not impede damper movement. (3)
e.
Cutout hole for 6” or 7” diameter duct exhaust hole in cabinet or
soffit, per figure 1C. Recommended attaching 6” collar & 7”
transition (with damper) to hood before setting into place.
f.
Drill Wiring Access hole in cabinet per figure 1C. (If not using a
plug), feed the wires coming down into top of the hood through the
opening in the bottom of the cabinet. (For recirculation kit
installation, you must feed wires through recirculation vent before
going into hood)
g.
Using the screws provided, fasten 4 hood screws into cabinet or
soffit at location identified. DO NOT SCREW IN ALL THE WAY,
LEAVE 1/8” OF SCREW SHOWING.
h.
Lift the hood up to the cabinet, such that the screws protrude
through the key holes on hood top. Push hood back flush against
the wall, so that screws support hood.
i.
While holding hood, tighten all 4 screws securely from under the
hood.
j.
NOTE: Install additional screws through the back or top for
security.
2. CONNECT DUCTWORK
a.
1.
2.
Connect 6” or 7” metal duct to collar or
transition.
Your METAL Exterior Exhaust Outlet (Purchased Separately),
installed at the end of your duct run on the roof or outer wall
of your home must include an integrated damper to block the
intrusion of outside air into the home.
3.
9
INSTALLATION
3. ELECTRICAL CONNECTION
Electrical Connection can be done by installing an outlet in
the cabinet and securing a plug onto the wires from hood or
bringing wires into hood as shown below.
a.
Verify that power is turned off at the source.
b.
Make electrical connections with wire nuts (Purchased Separately)
as shown. If house wiring is not 2-wire with a ground wire, a
ground must be provided by the installer.
Green or Bare = Ground
Black = Hot
White = Neutral
4. Completion
a.
Turn Power back “ON” from the Circuit or Fuse box.
b.
Activate blower and lights to confirm proper function.
c.
Remove ALL protective film from the exterior of your hood and
filters.
10
Optional Recirculation Kit *
Installation
Electrical
Opening
1-3.
6.
4.
Optional Recirculating Kit
Purchased Separately from your Dealer
1.
Place Recircutating Vent under cabinet and mark position of holes allowing for
unit to slide back in the keyhole slots. (1)
2.
Drive screws into underside of cabinet leaving a ⅛” protrusion.
3.
Install metal vent to underside of cabinet onto mounting screws and slide back to
rear wall. Tighten Screws.
4.
Fasten diverter to top of hood as shown, by screwing 4 sheet metal screws
(provided) into the pre-dilled holes.
5.
Follow “Installation” from page 8
6.
Drive machine screws (provided) into underside of Recirculation Kit, leaving
a ⅛” protrusion.
7.
Install hood to underside of Recirculation Lit onto mounting screws and slide
back to rear wall. Tighten Screws. Add additioal screws to back wall if
neccessary
8.
Install Charcoal Filters to sides of blower inside Hood
11
OPERATION & FEATURES
1. EASY ACCESS CONTROL SWITCH (from left to right)
0
Button 0 – Fan Off
1
Button 1 – Low
2
Button 2 – Medium
3
Button 3 – High

Light On/Off Control
0 1 2 3 
    
2. MESH FILTERS
a.
(3) 10-3/4” x 15” Dishwasher Safe Aluminum Mesh filters
3. PUTTING IN THE MESH FILTERS
a. Insert the Filter into the unit at an angle. (Fig. 3b)
b. Push the Mesh filter upward(Fig. 3c)
c. Snap into place(Fig. 3c)
Fig. 3b
Fig. 3c
12
CLEANING & MAINTENANCE
WARNING!!!
To prevent the possibility of a fire and explosion, do not
use flammable liquids or solvents to clean the unit or any of
its parts.
Check to make sure all power sources are disconnected
before servicing or taking unit apart for cleaning.
Please thoroughly clean the unit weekly
1. RANGE HOOD
a.
Use household cleaner to remove grease or dirt from the outer shell
of the unit. Spray on wiping cloth or sponge and wipe in the
direction of the grain to avoid scratching the unit. (DO NOT SPRAY
DIRECTLY ONTO UNIT)
b.
Stainless steel cleaners can help keep your rangehood bright and
clean.
2. MESH FILTERS
a.
Clean the Mesh filters regularly for the most efficient suction power.
b.
Let it soak thoroughly in warm soapy water overnight, wipe with
sponge and rinse.
c.
OR
Mesh filters may be cleaned using residential dishwasher.
TROUBLESHOOTING
13
TROUBLESHOOTING
WARNING!!!
Check to make sure all power sources are disconnected
before starting any troubleshooting. Safety gloves and
glasses should be worn when working on the unit. Serious
injury or death may occur if safety precautions are not
followed.
VEHOOD3610 Series
LED Light Issue
1. LED lights may need to be changed. Contact
EuroChef or replacement bulb.
Unit Lacks Power
1. Confirm that circuit breaker is “ON”
2. All wiring is connected.
Unit making humming
noise
1. Replace defective capacitor with new one.
Fan Blower Fails
Call for Service
14
Parts / Replacement & Wiring Diagram
PARTS LIST
Item
Name
Part Number
1
Spacer
2
Lamp Panel
3
LED Lamp
C1-0403-0306
4
Switch
C1-0405-0303
5
Capacitor
C1-0401-A250-22
6
LED Driver
C1-0402-D001
7
Motor / Blower
C1-0302-A110-06A
B101-7236-09
B101-7236-06
8
Aluminum Filter
C1-0604-0107
10
Recirculating Kit
(Optional)
RK36
11
Charcoal Filters for
Recirculating Kit
C1-0603-0303
How to Order Parts
Contact Eurochef USA:
866-844-6466 or submit a service call at
www.veronaappliances.com
Accessories
10.
Recirculation kit with Charcoal Filters
11.
Replacement Charcoal Filters
10
11
Parts / Replacement & Wiring Diagram
15
WARRANTY / CONTACT US
16
LIMITED WARRANTY
Verona Hoods warrants its product against defects in material or workmanship as
follows:
Labor: For a period of one (1) year from the date of purchase, if the product is
determined to be defective, Verona will attempt to repair the product, at its option,
at no charge. After the warranty period, customer must pay for all labor charges.
During the "labor" warranty period there will be no charge for any work done on
the purchased model. (All labor repairs are limited only to the installation of
electrical components.)
Parts: In addition, Verona will supply, at no charge, new or rebuilt replacements
in exchange for defective parts for a period of one (1) year. After the warranty
period, customer must pay for all parts. During the "parts" warranty period, there
will be no charge for parts
You must provide the serial number of your unit for any replacement parts during
the warranty period. This warranty applies to products purchased and serviced in
the United States only.
* Verona will attempt to repair malfunctioning units prior to shipping a
replacement. In the case that a unit cannot be repaired and must be replaced,
Verona will not be held liable for removal or installation fees of the malfunctioning
and replacement unit.
17
WARRANTY / CONTACT US
WHAT IS NOT COVERED BY MANUFACTURER WARRANTY
1.
Damages resulting from any of the following:
a.
Improper installation or maintenance
b.
Any repair, modification, alteration or adjustment not
authorized by the manufacturer or an authorized service dealer
c.
Misuse and/or accidents
d.
Incorrect electric current, voltage or power supply
e.
Improper setting of any control (Pressing multiple selections at
the same time)
f.
Improper chemical cleaning (commercial or industrial cleaning
agents)
2.
Products purchased for use in a commercial or industrial setting (such
as in a hotel, office, restaurant, or other business)
3.
Damage resulting from natural disasters (earthquake, flood, storm, etc.)
4.
Aluminum Filters, Charcoal Filters and Light Bulbs
CONTACT US
Verona
41 Mercedes Way, Suite 25
Edgewood, NY 11717
TEL: (866) 844 - 6566
FAX: (631) 254 - 3426
E-mail: info@veronaappliances.com
Information subject to change without notice
Download PDF

advertising