GE Monogram | ZV36TSFSS | Quick Specs | GE Monogram ZV36TSFSS Quick Specs

zv36Tsfss – GE Monogram 36" Stainless Steel Professional Hood
Dimensions and Specifications (in inches)
28"
12"
18"
25"
35-15/16"
Model ZV36T With Tapered Sides
Installation Clearances
These vent hoods are designed to be installed onto a wall or beneath a
soffit or cabinet.
• Install these hoods* 30" min. to 36" max. above the cooking surface.
*These hoods may be installed 24" min. above a gas or electric drop-in
style cooktop. Always observe the 30" to 36" clearance when installed
over any professional style cooktop or range.
Soffit Installation Soffit
Installation
Note: Clearances may vary due to type of cooking product and local
codes. Check with local inspectors to be sure standard is applicable.
Wall Mount Installation
Wall Mount Installation
SOFFIT
30" MIN.
36" MAX.
In this installation the ductwork running from the top of the hood will
be concealed in the soffit or upper cabinetry.
30" MIN.
36" MAX.
For this installation, a decorative duct cover is available to conceal the
ductwork running from the top of the hood. Use of the duct cover requires
special consideration to the installation height above the countertop.
For answers to your Monogram, GE Profile or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center service, 800.626.2000.
®
Specification Revised 6/11
130650
Listed by
Underwriters
Laboratories
®
™
zv36Tsfss – GE Monogram 36" Stainless Steel Professional Hood
Advanced Planning
Ductwork Planning
• These vent hoods are equipped for 10" round ductwork. In most instances
they may be transitioned to 8" round.
• This hood may be vented vertically through upper cabinets, soffit or ceiling.
A duct transition piece is supplied for vertical exhaust. Use locally supplied
elbows to vent horizontally through the rear wall.
• Determine the exact location of the vent hood.
• Plan the route for venting exhaust to the outdoors.
• Use the shortest and straightest duct route possible. For satisfactory
performance, duct run should not exceed 150 ft. equivalent length for
any duct configurations.
• Refer to “Duct Fittings” chart to compute the maximum permissible length
for duct runs to the outdoors.
• Use metal ductwork only.
•Install a wall cap or roof cap with damper at the exterior opening. Order
the wall or roof cap and any transition needed in advance.
Wall Framing for Adequate Support
• These vent hoods are heavy. Adequate structural support must be provided.
Hoods must be secured to vertical studs in the wall.
• It is strongly recommended that the vent hood with duct cover be on site
before final framing and wall finishing. This will also help to accurately
locate the ductwork and electrical service.
Decorative Duct Covers:
Decorative duct covers, 6" and 12" high, are available to fit all models. The
duct cover conceals the ductwork running from the top of the hood to the
ceiling or soffit. Stack one or more duct covers over the top of the hood
to reach your ceiling height.
power supply
important – (Please read carefully)
WARNING:
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before beginning installation.
Do not use an extension cord or adapter plug with this appliance. Follow
national electrical codes or prevailing local codes and ordinances.
Electric supply
These vent hoods must be supplied with 120V, 60Hz, and connected to an
individual, properly grounded branch circuit, and protected by a 15 or 20 amp
circuit breaker or time delay fuse.
• Wiring must be 2 wire with ground.
• If the electrical supply does not meet the above requirements, call a
licensed electrician before proceeding.
• Route house wiring as close to the installation location as possible on the
back wall or ceiling.
• Connect the wiring to the house wiring in accordance with local codes.
Grounding instructions
The grounding conductor must be connected to a ground metal, permanent
wiring system, or an equipment-grounded terminal or lead on the hood.
WARNING: The improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a qualified
electrician or service representative if you are in doubt whether the appliance
is properly grounded.
Optional Duct Cover Accessories
6" Duct Cover
12" Duct Cover
Decorative duct covers are available in 6" and 12" heights. Duct covers may be
stacked, in various combinations, to conceal the ductwork running from the
top of the hood to the ceiling.
• Before you begin, you should determine the installation height of the hood
and order the correct size duct cover. The duct covers should be ordered at
the same time as the vent hood and be on site before
installation. Order the duct cover corresponding to your model.
Specification Revised 6/11
130650
6" Duct Covers
Hood Model
ZV48T, ZV48S
ZV36T, ZV36S
ZV30T, ZV30S
6" Duct Cover
ZX48DC6
ZX36DC6
ZX36DC6
Dimensions
6"H x 19-11/16"W x 11-7/8"D
6"H x 15-3/4"W x 11-7/8"D
6"H x 15-3/4"W x 11-7/8"D
12" Duct Covers
Hood Model
ZV48T, ZV48S
ZV36T, ZV36S
ZV30T, ZV30S
12" Duct Cover
ZX48DC12
ZX36DC12
ZX36DC12
Dimensions
12"H x 19-11/16"W x 11-7/8"D
12"H x 15-3/4"W x 11-7/8"D
12"H x 15-3/4"W x 11-7/8"D
For answers to your Monogram, GE Profile or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center service, 800.626.2000.
®
Listed by
Underwriters
Laboratories
®
™
zv36Tsfss – GE Monogram 36" Stainless Steel Professional Hood
Using Duct Cover Accessories
We recommend that the vent hood and decorative duct cover (if used) be
on site before final framing and wall finishing. This will help to
accurately locate studs, ductwork and electrical service.
• Read these examples carefully to determine the need for one or more
6" or 12" duct covers.
To avoid unsightly gaps, plan the hood installation height for duct covers
use. Use the following formula to calculate the need for one of more
duct covers and to ensure a trouble free installation.
Ceiling Height
B
A = Countertop to ceiling height.
B = Gap at the top of the hood to the ceiling.
C = Hood installation height – Plus 18" hood height.
18" Hood
Height
A
NOTE: Dia. C should be between 48" and 54" (for a 30" to 36" installation
height). Raise or lower the hood installation height to allow use of one
or more 6" and 12" duct covers.
C
A-B=C
INSTALLATION EXAMPLES
8 ft. Ceiling
12"
10 ft. Ceiling
9 ft. Ceiling
30"
24"
30"
8 ft. ceilings: When the hood is installed 30"
above the cooking surface and there is no
soffit or upper cabinetry, order one 12" duct
cover accessory.
36"
30"
9 ft. ceilings: When the hood is installed 30"
above the cooking surface, order two 12" duct
cover accessories.
10 ft. ceilings: When the hood is installed 36"
above the cooking surface, order three 12" and
one 6" duct cover accessories.
For answers to your Monogram, GE Profile or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center service, 800.626.2000.
®
Specification Revised 6/11
130650
Listed by
Underwriters
Laboratories
®
™
zv36Tsfss – GE Monogram 36" Stainless Steel Professional Hood
Features and Benefits
• 620 CFM Vertical Exhaust
• Variable Speed Fan Control
• 2 Halogen Lamps with 4 Lighting Levels
• Infrared Warming Lamp
• Utensil Rod
• Removable Grease Trays
• Removable Baffle Stainless Steel Filters
• Model ZV36TSFSS – Stainless steel
ZV36TSFSS
Specification Revised 6/11
130650
Download PDF

advertising