GE | GTD45EASJWS | Spec sheet | GE GTD45EASJWS Spec Sheet

GE GTD45EASJWS Spec Sheet
GTD45EASJ
GE® Series 7.2 Cu. Ft. Capacity Aluminized Alloy Drum Electric Dryer with HE Sensor Dry
Dimensions and Installation Information (in inches)
Electric Dryer Rating:
240V
5600W
24A
60Hz
208V
4400W 22A
60Hz
22 1/2"
29 1/2"
27"
Power Cord 4 1/2"
27"
11 3/4"
Exhaust Option: 4-way rear, right, left and bottom
Circuit Requirements: An individual, properly-grounded
branch circuit, protected by a 30-amp circuit breaker or a time-delay
fuse, is required.
Note: Dryer wall outlet must be located within 36" of service cord
entry and acessible when dryer is mounted in position.
44"
37 1/2"
Installation Information: For complete information, see
installation instructions packed with your dryer.
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces5.7
are:cu. ft. Dryers
0" either side; 3" front and rear
2
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of
open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a
minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Power
Bathroom or Bedroom Installation:
Cord Hole
• The dryer MUST be exhausted to the outdoors.
30-1/2
• The installation must conform with the local codes, or in the absence of local codes, with the
National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces are: 0" both sides; 3" rear
Back View
Dryer Exhausting Information­: Use metal duct only, vertical and horizontal
ducting.
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
8"
3 1/2"
1 3/4"
5"
3 1/4"
Side View
Rear View
Side View
Rear View
5.8,
6.0 and
7.0Locations
cu. ft. Dryers
Power
Cord
5
Power
Cord Hole
4-1/2
BAck
View
Back
View
Listed by
Underwriters
Laboratories
Specification Created 7/15
GTD45EASJ
GE® Series 7.2 Cu. Ft. Capacity Aluminized Alloy Drum
Electric Dryer with HE Sensor Dry
For complete information, see installation instructions
packed with your dryer.
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all rigid metal
exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semirigid) ducting can be used (Kit WX08X10077). In special installations, it may be
necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A
UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid
metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can
be maintained throughout the entire length of the transition duct. Please see installation
instruction packed with your dryer for complete instructions when using flexible metal
(foil type) ducting.
Exhaust Length Calculation:
1.Determine the number of 90° turns needed for your installation. If you exhaust to
the side or bottom of dryer, add one turn.
2.The maximum length of 4" rigid (aluminum or galvanized) duct which can be
tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns
within the duct length should be treated as a 90° elbow. A turn over 45° should be
treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any
enclosed house floor (crawl space), or into an attic, since the accumulated lint could
create a fire hazard or moisture could cause damage. Never terminate the exhaust into a
common duct or plenum with a kitchen exhaust, since the combination of lint and grease
could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
For more information on venting kits and accessories,
please call 1-800-GE-CARES.
Dryer exhausting information—
use metal duct only vertical and
horizontal ducting
A
A 4
B
A
4
B
Domestic dryer models
2-1/2
GE Frontload Long Vent 7.0
cu. ft. capacity electric dryer
(GFDL)
Long Vent 6.0 - 8.0 cu. ft.
capacity electric & gas dryers
(GTDL and GTV)
Long Vent 7.0 cu. ft. capacity
electric & gas (GTD42, GTD45,
GTD65, GTX42 and GTX60)
All 6.0 - 8.3 cu. ft. capacity
models electric and gas dryers
(GFDS, GFDR, GFDN, GTDS,
GTDN, GHDN, GHDS, GTDP,
GLDP, GTD, HTDP, HTDX)
DCVH480
All 3.6 cu. ft. (DSKS, DSKP)
electric dryers
Laundry Center GUD27
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
2-1/2
Laundry Center GUD24
Best performance
Maximum length
of 4" dia rigid
metal duct
Exhaust hood type
Number of
A
B
90° turns 4" opening
2-1/2" opening
0
200 ft.
175 ft.
1
185 ft.
2
175 ft.
165 ft.
155 ft.
3
165 ft.
145 ft.
4
155 ft.
135 ft.
5
145 ft.
125 ft.
0
1
2
3
4
5
0
1
2
3
4
5
0
150 ft.
135 ft.
125 ft.
115 ft.
105 ft.
95 ft.
120 ft.
100 ft.
85 ft.
70 ft.
60 ft.
55 ft.
90 ft.
125 ft.
115 ft.
105 ft.
95 ft.
85 ft.
75 ft.
90 ft.
75 ft.
65 ft.
55 ft.
45 ft.
35 ft.
60 ft.
1
2
3
4
0
1
2
3
0
60 ft.
45 ft.
35 ft.
25 ft.
90 ft.
60 ft.
45 ft.
35 ft.
46 ft.
45 ft.
35 ft.
25 ft.
15 ft.
60 ft.
45 ft.
35 ft.
25 ft.
37 ft.
1
2
3
0
37 ft.
30 ft.
23 ft.
56 ft.
30 ft.
22 ft.
15 ft.
42 ft.
1
2
3
0
1
2
48 ft.
40 ft.
32 ft.
43 ft.
33 ft.
24 ft.
34 ft.
26 ft.
18 ft.
36 ft.
26 ft.
16 ft.
Specification Created 7/15
GTD45EASJ
GE® Series 7.2 Cu. Ft. Capacity Aluminized Alloy Drum
Electric Dryer with HE Sensor Dry
Features and Benefits
HE Sensor Dry – Keep your clothes looking and feeling their best. Dual thermistors
continually monitor temperature with a sensor bar that measures moisture to
prevent over-drying
Up to 120 ft. venting capability – Provides flexible installation
Extended Tumble – Freshly tumbles your garments periodically for up to 8 hours
when unable to move clothing to the dryer right away
End-of-cycle signal – Alerts you when the load is done, so clothes can be removed
before wrinkles set in
Model GTD45EASJWS – White with silver backsplash
GTD45EASJWS_GTD45GASJWS
Specification Created 7/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising