Whirlpool | WGD85HEFW | Dimensions | Whirlpool WGD85HEFW Dimensions

GAS DRYER
PRODUCT MODEL NUMBERS
WGD7505F, WGD7540F, WGD7590F, WGD75HEF, WGD7740F, WGD77HEF,
WGD90HEF, WGD92HEF, WGD85HEF
Front view
Side view
27"
(686 mm)
383/4" Min.
(984 mm)
39" Max.
(990 mm)
* Approx. measurement
Back view
Recommended installation clearances
6/"
(159 mm)
1 4
18" min.
(457 mm)
(Steam Models Only)
Vent
31/2"*
(89 mm)
0" - 5"*
(0" - 127 mm)
3"
(76 mm)
Gas
/4"*
(18 mm)
3
48 in.2 min.
(310 cm2)
297/8"*
(759 mm)
Water inlet
53/4"*
(146 mm)
3"
(76 mm)
143/8"
(365 mm)
253/4"
(654 mm)
61/8"*
(156 mm)
1"*
(25 mm)
24 in.2 min.
(155 cm2)
1"
(25 mm)
* Approx. measurement
NOTE: Most installations require a minimum of 5" (127 mm)
clearance behind dryer for exhaust vent with elbow. See
“Venting Requirements.”
Spacing for recessed area or closet installation
All dimensions show recommended and minimum spacing allowed.
■■ Additional spacing should be considered for ease of
installation and servicing.
■■ Additional clearances might be required for wall, door, floor moldings, dryer venting, and gas line.
■■ Additional spacing should be considered on all sides
of the dryer to reduce noise transfer.
■■ For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings
are acceptable.
■■ Companion appliance spacing should also be considered.
W10775221A
05/2016
INSTALLATION REQUIREMENTS
GAS SUPPLY REQUIREMENTS
Gas supply: This dryer is equipped for use with Natural gas. Dryer can be converted to L.P. gas. When rigid pipe is used it should
be 1/2" IPS. When acceptable to the gas supplier and local codes, 3/8" approved tubing may be used for lengths under 20 ft (6.1 m).
For lengths over 20 ft (6.1 m), larger tubing should be used. Pipe-joint compounds resistant to the action of L.P. gas must be used.
An individual manual shutoff valve must be installed within 6 ft (1.8 m) of the dryer in accordance with the National Fuel Gas Code
ANSI Z223.1.
ELECTRICAL REQUIREMENTS
A 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply is required. A time-delay fuse or circuit breaker and a separate circuit
are recommended.
WATER (STEAM MODELS ONLY) REQUIREMENTS
The dryer must be connected to the cold water faucet using new inlet hoses. Do not use old hoses. Do not overtighten. Damage to the
coupling can result.
VENTING REQUIREMENTS
Exhaust venting: Exhaust your dryer to the outside. 4" (102 mm)
diameter vent is required. Rigid or flexible metal exhaust vent
must be used. Do not use plastic or metal foil vet. Exhaust hood
must be at least 12" (305 mm) from the ground or any object that
may be in the path of the exhaust.
Determine vent length and elbows needed for best
drying performance:
■■
Use the following Vent System Chart to determine type
of vent material and hood combinations acceptable to use.
NOTE: Do not use vent runs longer than those specified
in Vent System Chart. Exhaust systems longer than those
specified will:
■■
Shorten life of dryer.
■■
Reduce performance, resulting in longer drying times
and increased energy usage.
Exhaust hoods:
Recommended styles:
Louvered Hood
Box Hood
Acceptable style:
Angled Hood
Determine vent path:
■■
Select route that will provide straightest and most direct
path outdoors.
■■
Plan installation to use fewest number of elbows and
turns.
■■
When using elbows or making turns, allow as much
room as possible.
■■
Bend vent gradually to avoid kinking.
■■
Use as few 90° turns as possible.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Vent System Chart
Number of
90° elbows
Type
of vent
Box/louvered
hoods
Angled
hoods
0
1
Rigid metal
64 ft. (20 m)
58 ft. (17.7 m)
Rigid metal
54 ft. (16.5 m)
48 ft. (14.6 m)
2
Rigid metal
44 ft. (13.4 m)
38 ft. (11.6 m)
3
Rigid metal
35 ft. (10.7 m)
29 ft. (8.8 m)
4
Rigid metal
27 ft. (8.2 m)
21 ft. (6.4 m)
NOTE: Bottom exhaust installations have a 90º turn inside the
dryer. To determine maximum exhaust length, add one 90º turn to
the chart.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising