Whirlpool | WFW85HEFC | Dimension Guide | Whirlpool WFW85HEFC Dimension Guide

Whirlpool WFW85HEFC Dimension Guide
Front-Loading Washer
PRODUCT MODEL NUMBERS
PRODUCT MODEL NUMBERS
WFW7590F, WFW75HEF, WFW90HEF,
WFW92HEF
WFW7590F, WFW9290F, WFW85HEF
Washer Dimensions:
53¼"
3/4"
52
(1353
(1340 mm)
mm)
Washer Dimensions:
27"
(686 mm)
335/16"
(846 mm)
51½"
3/4"
52
(1308 mm)
mm)
(1340
383/4" - 393/4"
(948 mm - 1010 mm)
27"
(686 mm)
383/4" - 393/4"
(948 mm - 1010 mm)
Recessed or closet installation stacked washer and dryer
3"
(76 mm)
1/8"
31½"
33
(800 mm)
mm)
(841
Recessed area or closet installation (washer only):
3"
(76 mm)
6"
(152 mm)
48 in.2
(310 cm2)
6"
(152 mm)
48 in.2
(310 cm2)
761/2"
(1943 mm)
24 in.2
(155 cm2)
761/2"
(1943 mm)
24 in.2
(155 cm2)
3"
(76 mm)
1"*
(25 mm)
5"
(127 mm)
* Add spacing of 1" (25 mm) on all sides of washer/dryer.
3"
(76 mm)
1"*
(25 mm)
5"
(127 mm)
* Add spacing of 1" (25 mm) on all sides of washer.
W10775528A
05/2016
Undercounter installation washer only:
Custom cabinet installation (washer only):
7"
(178 mm)
14"
(356 mm)
1"
(25 mm)
4"
(102 mm)
** Recommended 4" (102 mm), minimum 1.5" (38 mm)
All dimensions show recommended spacing allowed, except for closet door
ventilation openings which are the minimum required.
For each arrangement, consider allowing more space for ease of installation
and servicing, and spacing for companion appliances and clearances for walls,
doors, and floor moldings.
Space must be large enough to allow door to fully open. Add spacing of 1" (25
mm) on all sides of washer to reduce noise transfer. If a closet door or louvered
door is installed, top and bottom air openings in door are required.
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is
recommended that a separate circuit serving only this appliance be provided.
DRAIN SYSTEM
Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need.
IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of drain hose should be inside standpipe. Always secure drain hose
with cable tie.
Floor standpipe drain system
4.5"
(114 mm)
Laundry tub drain system
4.5"
(114 mm)
min.
30"
(762 mm)
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. A 1/4" (6 mm)
diameter to 1" (25 mm) diameter Standpipe Adapter Kit is
available (Part Number 3363920). Top of standpipe must be at
least 30" (762 mm) high; install no higher than 96" (2.44 m) from
bottom of washer. If you have an overhead sewer and need to
pump higher than 96" (2.44 m), a sump pump and associated
hardware are needed. See “Alternate Parts”.
Minimum capacity: 20 gal. (76 L). Top of laundry tub must
be at least 30" (762 mm) above floor; install no higher than
96" (2.44 m) from bottom of washer.
Floor drain system
Wall standpipe drain system
4.5"
(114 mm)
See requirements for floor standpipe drain system.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. See “Alternate Parts”. Minimum siphon
break height: 28" (710 mm) from bottom of washer. (Additional
hoses may be needed.)
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising