GE | GTD75GCPLDG | Quick Specs | GE GTD75GCPLDG Quick Specs

GE GTD75GCPLDG Quick Specs
GTD75GCPL/GCSL
GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
EXHAUST OPTION: When viewed from the front
of the unit, exhaust 3-way via rear, left and bottom.
Dryer is shipped exhausted to the rear. Alternate
exhausting knockouts are supplied.
GAS: An individual, properly-grounded branch circuit,
with a three-prong grounding-type receptacle, protected
by a 15 or 20 amp circuit breaker or a time-delay fuse is
required.
GAS DRYER ELECTRIC RATING: 120V, 60Hz, 6A
GAS (BTU/HR): 22,000. Factory-equipped for
natural gas. Tested for LP gas. LP gas supply requires
a conversion kit. Check installation instructions for
correct kit and have a qualified gas technician install a
conversion kit. See dryer ducting information for proper
installation.
NOTE: Dryer wall outlet must be located within 36" of
service cord entry and accessible when dryer is mounted
in position.
INSTALLATION INFORMATION: For complete
information, see installation instructions packed with
your dryer.
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
- If your dryer is approved for installation in an alcove or closet, it will be stated on a
label on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces
are: 0" either side; 1" front, top and rear
- Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a
gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local
codes, with the National Electric Code and National Fuel Gas Code, ANSI
Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET
INSTALLATION:
- Minimum clearances to combustible surfaces are: 0" both sides; 1" rear
DRYER EXHAUSTING INFORMATION­:
- Use metal duct only, vertical and horizontal ducting.
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Specification Revised 9/17
GTD75GCPL/GCSL
GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
5.7 cu. ft. Dryers
5.8,
6.0 and
7.0
cu. ft. Dryers
POWER
CORD
LOCATIONS
5
2
22 1/2"
30 1/2"
27"
Power Cord 4 1/2"
27"
Power
11 3/4"
30-1/2
Power
Cord Hole
Cord Hole
4-1/2
Back View
Back View
48"
40 1/2"
8"
3 1/2"
Side View
1 3/4"
5"
3 1/4"
Rear View
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Specification Revised 9/17
GE Dryer Vent
GTD75GCPL/GCSL
GE Dryer Vent
GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry
FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED
WITH YOUR DRYER.
DUCTING MATERIALS:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust
duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can
be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer
to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type)
duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting
cannot be used AND where a 4" diameter can be maintained throughout the entire length of
the transition duct. Please see installation instruction packed with your dryer for complete
instructions when using flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or
bottom of dryer, add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length
should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard
or moisture could cause damage. Never terminate the exhaust into a common duct or plenum
with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
DRYER EXHAUSTING INFORMATION—
USE METAL DUCT ONLY VERTICAL AND
HORIZONTAL DUCTING
BEST PERFORMANCE
A
A 4
B
A
4
2-1/2
Domestic dryer
B models
Long Vent 6.1-7.4 cu. ft.
capacity electric & gas
2-1/2
Maximum length
of 4" dia rigid
metal duct
Exhaust hood type
Number
A
B
of 90°
4"
2-1/2"
turns
opening opening
0
120 ft.
90 ft.
1
100 ft.
75 ft.
2
85 ft.
65 ft.
3
70 ft.
55 ft.
4
60 ft.
45 ft.
5
55 ft.
35 ft.
For every extra 90° elbow, reduce the allowable vent system
length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
When calculating the total vent system length, you must add all
the straight portions and elbows of the system (including the
transition duct.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES,
PLEASE CALL 1-800-GE-CARES.
Specification Revised 9/17
GTD75GCPL/GCSL
GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry
FEATURES AND BENEFITS
Steam Select - For the best results, customize your cycle by specifying the number of
Mixed Load
Cottons
WiFi Connect - Control and monitor your laundry from anywhere with a smart device
Hold 3 Secs
to Store
Casuals
Delay
Est. Time Remaining
garments needing to be steamed
Towels /Sheets
Drying Cooling Done
Delicates
90 min.
Bulky Items
60
Speed Dry
More Dry
High
Dry
Medium
Less Dry
Low
Damp
No Heat
40
Sanitize
Steam Refresh
3 - 5 Garments
Steam Dewrinkle
9 - 13 Garments
20
Jeans
Time Dry Cycles
Time
Timed Dry
My
Cycle
Delay
Dry
Volume
10
Level
Temp
Damp
Alert
Drum Light
Hold 3 Secs
Warm Up
Extended
Tumble
eDry
Time Adjust
Sensor Dry ™
Control Lock
Hold 3 Seconds
or Amazon Alexa
HE Sensor Dry - Takes the guesswork out of drying times by sensing the moisture in
the drum and drying accordingly
Up to 120 ft. venting capability - Provides flexible installation
Extended Tumble - Tumble clothes without heat to help prevent creasing and wrinkling
ENERGY STAR® qualified - Meets or exceeds federal guidelines for energy efficiency
for year-round energy and money savings
My Cycle Settings - Dry clothes with the settings you prefer on any cycle, rather than
the defaults, and store your settings for later use
Damp Alert - Alerts you when clothes are the ideal dampness for ironing, for perfectly
wrinkle-free results
Y-connector, short and long steam hoses included
Model GTD75GCSLWS – White with silver backsplash
Model GTD75GCPLDG – Diamond Gray
Specification Revised 9/17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising