U-Line | UCO2175FB00 | Full Overlay Panel Specs and Installation | U-Line UCO2175FB00 Full Overlay Panel Specs and Installation

U-Line UCO2175FB00 Full Overlay Panel Specs and Installation
DOOR PANEL INSTALLATION GUIDE
®
Overlay Door Panel
Preparation and Installation
Instructions
The Built-In Undercounter Leader Since 1962
U-LINE.COM
Overlay Door Panel
Door panel Preparation
A Full overlay door panel completely covers the door frame and
handle to give you a built-in appearance. See your U-Line dealer for
the optional Full Overlay Door Panel Kit.
Full Overlay Door Panel Kit Part Number
2175
Black
U-OL2175B
2175
White
U-OL2175W
2115 & 2160
Black
U-OL2115B
2115 & 2160
White
U-OL2115W
Included In Kit:
•
•
•
•
•
1x Replacement Handle •
2x Pivot Plate
•
1x Overlay Cap
•
8x #6x2” Drywall Screw •
2x 8-32 x 3/8” Screws
2x Hinge Plates
1x Door Closer
2x Pivot Posts
8x 8-32 x1/2” Screws
1. Determine cabinet toe kick height, by measuring the difference
between the surface the appliance will rest on and the bottom
of the adjacent cabinetry. Adjust panel height according to the
height of you cabinetry’s Toe Kick.
2. Cut the overlay to the dimensions in Table A & B.
3. Drill hole for upper door hinge (top of panel) using a
#16 drill bit (0.177” diameter) x 11/16” deep (See diagram
below)
4. Drill hole for lower door hinge 5/16” diameter x 1/4” deep (See
diagram below)
Table A (Width)
Model
Width
2175
23 3/4”
2115 & 2160
14 3/4”
Table B (Height)
Toe Kick
Height
Toe Kick
Height
3 3/4”
29 3/4”
4 1/4”
29 3/8”
• The door panel must not weigh more than 20lbs.
3 7/8”
29 3/4”
4 3/8”
29 1/4”
•
4“
29 5/8”
4 1/2”
29 1/4”
4 1/8”
29 1/2”
IMPORTANT
•
•
It is important to ensure that all drilled holes are drilled to the
correct depth in order to avoid splits in the wood when
hardware is installed.
Rear view of wood panel for right-hand hinge shown. Use
mirror image for left hand hinges.
Appliance will need up to 34 1/2” to the under side of the
counter to leave room for leveling adjustments
Note: Table B dimensions will vary based on the level of the floor.
If floor is uneven, cut panel to the next longer dimension and
adjust level legs to achieve proper fit
BACK SURFACE MUST BE A FLUSH FLAT SURFACE
FOR PANEL DOORS USE A BACKER BOARD
.750
MIN
23.750
Detail A
*75 Series
14.750
*BI2115 & 2160 Series
SEE DETAIL
A
15/32
3/8
C
3/16
C
13/16
Detail B
1/4
5/16
CHAMFER 1/32" X 45°
D
3/8
D
13/32
SEE DETAIL
B
U-Line Door Panel Installation Guide
1
Installation Instructions
Removing Existing Door
4 1/16”
1. Remove the door shelves by first pulling shelves at a 45° angle,
then straight out.
11/16”
2. Remove the top hinge screw pin (Phillips screwdriver). Remove
the door by tilting forward and lifting off the bottom hinge pin.
10 1/2”
Old Handle
New Handle
ULIN_0403_A
12 1/2”
3. Pull door gasket out of the groove (top edge of door only). Start
in the middle and pull outward, moving toward the edge. This
may take some force.
4. Remove the two screws located on both sides of the handle. Do
not discard screws.
5. Remove the handle and discard. (This handle will be replaced
with the overlay handle included in the Full Overlay Door Panel
Kit).
6. Install the replacement Door Handle using the two screws
removed in step 4.
Preparing The Door Frame For Overlay
You have received your door with or without holes pre-punched
into the steel panel. If your panel does not have pre-punched holes
please reference diagram A for hole locations.
1. Lay the door down on a flat surface with the galvanized steel
panel facing upwards. If your unit was equipped with door
shelves, it may be helpful to prop up both door sides with 4x4’s
to keep the unit from pivoting.
2. Using a 9/64” Drill bit, drill through the steel panel and frame
using the holes in the steel panel as a guide, or the dimensions
provided in diagram A if your panel did not come pre-punched.
Be sure to drill completely through frame material.
Top Down Slice
View
Steel Plate
7/8”
A
2 7/16”
Panel installation
1. Lay prepared panel face down on a flat clean surface.
2. Carefully lay door down on top of panel, steel plate side down.
3. Line the top of the door flush with the top of the panel.
4. Using a 7/64” Drill bit, drill 8 pilot holes into the wood panel 3/
8” deep.
5. Locate the 8 #6x2”
screws provided in
the overlay panel
install kit.
6. Using a phillips head
bit, place one screw
into each of the 8
pilot holes and screw
down.
Overlay Panel
7. Be sure the screws
force their way past
the opening on the
gasket channel and sit
flush against the
bottom of the gasket
channel.
Overlay Panel
8. Starting at the
corners, re-install the gasket into the gasket channel in the
frame. Make sure the gasket is fully seated, this may take some
force.
U-Line Door Panel Installation Guide
2
Door Installation
Installing the Door
1. Remove the existing bottom pivot plate and replace with the
Full Overlay pivot plate.
1. Remove the existing hinge from the unit, saving the door closer
assembly, see below
2. Attach Overlay cap to door, opposite side of where hinges will
be, see below.
2. Install the replacement top and bottom hinge onto the unit, see
below.
3. Install the pivot post into the new Replacement Bottom Hinge
(using phillips screwdriver) and install the hinge onto the unit.
Overlay Cap
3/4" Wood Panel
4. Replace the door closure assembly onto the bottom pivot post.
Be sure the bosses on closures align with holes in hinge and
hinge plate.
Replacement Handle
Wood Panel Top Hinge Plate
(5/8" Longer than Existing Top Hinge Plate)
Pivot Post
#8-32 x 1/2"
Flat Head Screw
Three Places
3. Attach replacement Top Pivot Plate to door, on the side where
hinges will be. Use the two #8-32 x 1/2” Flat Head Phillips
screws (Black) supplied with kit, see below
Top Pivot Plate
Door Panel
ULIN_0405
#8-32 x 1/2" Flat Head Screws
Black, Two Places
3/4" Wood Overlay
Top Pivot Plate
Screw to attach Handle
Door Closure Top
Existing Door
Closure Assembly
Door Closure
Bottom
Pivot Post
4. Attach replacement bottom pivot plate; on the side where
hinges will be. Use the two #8-32 x 3/8 Hex Screws supplied
with kit, see below.
#8-32 x 1/2" Flat Head Screw
Three Places
Wood Panel Bottom Hinge Plate
(5/8" Longer than Existing Bottom Hinge Plate)
IMPORTANT
Existing
Door
Existing Bottom Pivot Plate
(Remove and Discard)
Pivot posts must be cleaned. Closers must also be clean
and greased to ensure proper operation.
Wood Panel Bottom Pivot Plate
(5/8" Longer Than
Existing Bottom Pivot Plate,
Flush Side Facing Out)
#8-32 x 3/8" SEMS Hex Screw
(2 Places)
5. Place the modified door onto the pivot post.
6. Position door and install the pivot post into the top hinge
7. Adjust door as needed for proper closure
8. Check to see that light goes off when the door closes.
5. Starting at the corners and working toward the center, push the
door gasket into place.
9. Reinstall the door shelves by lining up the bosses and first
pushing straight in, then down at a 45° angle.
U-Line Door Panel Installation Guide
3
Checking Door Alignment
The unit’s door is aligned at the factory before shipment. However,
it’s alignment could have been disturbed during shipment or during
door panel installation.
IMPORTANT
Properly aligned, the door should be 1/8” below the top of
the unit cabinet. NOT flush with the top. See Below.
1. Compare the top edge of the door to the top edge of the
cabinet.
4. Mount the door, recheck alignment and repeat Steps 2 and 3 if
further adjustment is necessary.
5. When top edge of door is parallel to top edge of cabinet,
remove the door and ensure the two screws are secure.
6. Remove the door closers from
the bottom hinge, clean
thoroughly and lubricate the
mating surface with a
petroleum jelly such as Vaseline.
7. Reinstall the closers, lining up
the bosses with holes in hinge
and hinge plate.
8. Mount the door and install top
hinge pivot pin.
1/8"
Note: The bottom of the panel will line up with the top of the
cabinetry toe kick. Minor adjustments can be made using the
leveler feet. Depending on the height of the toe kick, a small
portion of the door may be visible beneath the panel.
2. If the door edge is 1/8” below and parallel to the top of the
cabinet, the door is aligned. If it is not, note whether the side
opposite the hinge needs to be moved UP or DOWN, and use
the following procedure.
Note: If the door is adjusted correctly, but panel is not square with
the adjacent cabinets, slight adjustment can be made by drilling the
holes in the vinyl coated steel panel slightly oversized.
Adjusting Door Alignment
1. Remove top hinge screw pin. Remove door by tilting forward
and lifting off the bottom hinge pin.
2. With door upside-down, loosen, but do not remove the two
screws on the door’s bottom hinge plate.
Bottom Of Panel
Door Gasket
Slotted
Mounting
Holes
Existing Door
Notches
(Must Face Toward
Center of Door)
Toe Kick
Panel
Door Reveal
Wood Overlay
Lower
Outside
Door Edge
Raise
Outside
Door Edge
Right Hand Hinge Model Shown
3. If the top far edge of the door needs to move UP, move the
hinge plate toward the outside of the door and retighten screws.
If the top far edge of the door needs to move DOWN, move
the hinge plate toward the inside of the door and retighten
screws.
U-Line Door Panel Installation Guide
4
DOOR PANEL INSTALLATION GUIDE
®
SERVICE INFORMATION
If you have a problem with this appliance, your use and care guide has troubleshooting information to help you
quickly identify common problems and provide information on possible cause and remedy. Answers to
Customers Frequently Asked Questions are available at www.u-line.com/customer/faq.cfm. You may contact ULine directly:
GENERAL INQUIRIES:
SERVICE ASSISTANCE:
U-Line Corporation
P.O. Box 245040
Milwaukee, Wisconsin 53224-9540 U.S.A.
Phone (414) 354-0300
FAX (414) 354-7905
Email: sales@u-line.com
www.u-line.com
Phone (800) 779-2547
FAX (414) 354-5696
Email: onlineservice@u-line.com
www.u-lineservice.com
PARTS ASSISTANCE:
E-mail: onlineparts@u-line.com
ABOUT U-LINE
Building on 45 years, U-Line has captivated those with an appreciation for the finer things with exceptional
design, inspired innovations and attention to even the smallest details.
U-Line is synonymous with premium built-in under counter ice making, refrigeration and wine storage appliances, the U-Line Corporation is committed to luxury under the counter. U-Line is known and respected for
unwavering dedication to product innovation, quality and selection. A bold and broad line of models is the product of visionaries in the pursuit of distinctive living environments in the kitchen and spaces beyond.
In 1962, Henry Uihlein founded U-Line Corporation as an outgrowth of Ben-Hur Freezer Company and was
the first to develop and patent an automatic stand-alone under counter residential ice maker. His foresight and
determination to develop new ideas and to succeed when there were no clear guidelines or solutions are evident today. The Milwaukee, Wisconsin based family operated business provides continuity and vision from
which innovations continue to be born.
Going forward, U-Line will continue offering best-in-class products that build on the company's numerous patents and world firsts to guide the under counter industry in realizing its unlimited potential.
The Built-In Undercounter Leader Since 1962
U-LINE.COM
©2009 U-Line Corporation
Publication Number 30137 5/2011 Rev. J
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising