ALICE Quick-start guide HIGH-WALL DUCTLESS AIR CONDITIONING & HEATING SYSTEM FAN AUTO OPER AIR HEALTH X-FAN HUMIDITY FILTER TURBO HOUR ON/OFF 2 1 3 ON/OFF MODE 7 FAN 8 9 11 X-FAN TEMP TIMER TURBO SLEEP LIGHT ON/OFF button 2 MODE button 3 +/- button 4 FAN button 5 button 6 button 7 HEALTH SAVE button 8 X-FAN button 6 9 TEMP button 10 10 TIMER button 5 4 1 (Note: X-FAN is same with BLOW) 11 TURBO button 13 12 SLEEP button 12 13 LIGHT button Introduction for icons on display screen air mode Operation mode Auto mode Cool mode Dry mode Fan mode Heat mode set fan speed FAN AUTO OPER AIR HEALTH X-FAN HUMIDITY FILTER set temperature TURBO HOUR ON/OFF Child Lock Sleep mode Temp. display type :Set temp. :Indoor ambient temp. :Outdoor ambient temp. send signal health mode X-fan turbo mode TIMER ON/TIMER OFF set time left & right swing light 1 Up & down swing Introduction for buttons on remote controller Note: ● After putting through power, air conditioner will give out a sound and operation indicator " " is ON (red indicator). You can operate the air conditioner through the remote controller. ● At ON status, after each pressing button on remote controller, the signal icon " " indicates the signal has been sent to air conditioner. ● At OFF status, display screen on remote controller displays set temperature. At on status, display screen on remote controller displays the corresponding startup function’s icon. 1 ON/OFF button Press this button can turn on or turn off the air conditioner. After turning on the unit, operation indicator " " on indoor unit is ON (green indicator. Color may be different for different models)and indoor unit gives out a sound. 2 MODE button Press this button can select your required operation mode. AUTO COOL DRY FAN HEAT ● After selecting auto mode, air conditioner will operate automatically according to ambient temperature. Set temperature can’t be adjusted and also can’t be displayed. Press "FAN" button can adjust fan speed. Press " " button can adjust swing angle. ● After selecting cool mode, air conditioner operates under cool mode. Cool indicator " " on indoor unit is ON. You can press "+" or "-" button to adjust set temperature. Press "FAN" button can adjust fan speed. Press " " button can adjust swing angle. ● After selecting dry mode, air conditioner operates under dry mode at low speed. Dry indicator " " on indoor unit is ON. Under dry mode, fan speed can’t be adjusted. Press " " button to adjust swing angle. ● After selecting fan mode, air conditioner operates only under fan mode, All mode indicators on indoor unit is OFF. Operation indicator is ON. Press "FAN" button can adjust fan speed. Press " " button to adjust swing angle. ● After selecting heat mode, air conditioner operates under heat mode. Heat indicator " " on indoor unit is ON. You can press "+" or "-" button to adjust set temperature. Press "FAN" button to adjust fan speed. Press " " button to adjust swing angle. (Cooling only unit can’t receive the signal for heating mode.) 2 Introduction for buttons on remote controller Note: For preventing cold wind, after starting up heating mode, indoor fan will blow fan afterdelaying 1-5min. (Details time is decided by indoor ambient temperature) Temperature setting range on remote controller: 60.8~86°F (16~30°C). Fan speed setting range: auto, low speed, medium speed and high speed. 3 "+" or "-" button ● After each pressing of "+" or "-" button, it can increase or decrease set temperature 33.8°F(1°C) . Hold "+" or "-" button, 2s later, set temperature on remote controller will change quickly. After reaching to your required time, loosen the button. Temperature indicator on indoor unit will also change accordingly. (Temperature can’t be adjusted under auto mode) ● Under TIMER ON, TIMER OFF or Clock setting, you can press "+"or "-" button to adjust time. (Refer to TIMER button for details) 4 FAN button Pressing this button can set fan speed circularly as: auto (AUTO), low( medium( ), high( ). ), Auto Note: ● Under AUTO Speed,IDU fan motor will adjust the fan speed (high, medium or low speed) according to ambient temperature. ● Fan speed under dry mode is low speed. 5 button ● Press this button to start or stop up & down swing function.The remote controller defaults to simple swing condition. ● Press + button and button at the same time at unit OFF to switch between simple swing and static swing; blinks for 2 seconds. ● In static swing condition, pressing button, the swing angle of up & down louver changes as below: no display (horizontal louvers stops at current position) ● If the unit is turned off during swing operation,the louver will stop at present position. 3 Introduction for buttons on remote controller Note: When selecting " " with remote controller, it’s auto swing. Horizontal louver of air conditioner will swing up&down automatically at the maximum angle. When selecting " 、 、 、 、 swing. Horizontal louver of air conditioner will stop at that position as shown by the icon to swing. 6 button ● Press this button to start or stop left & right swing function. The remote controller defaults to simple swing condition. ● Press + button and button at the same time at unit OFF to switch between simple swing and static swing; blinks for 2 seconds. ● In static swing condition, pressing button, the swing angle of left & right louver changes as below: no display (horizontal louvers stops at current position) (swing angle is displayed dynamically) ● If the unit is turned off during swing operation,the louver will stop at present position. ● When selecting " " with remote controller, it’s auto swing. Horizontal louver of air conditioner will swing left&right automatically at the maximum angle. ● When selecting " 、 、 、 、 " position swing. Horizontal louver of air conditioner will stop at that position as shown by the icon to swing. ● When selecting " ", it’s the circulating swing. Horizontal louver of (swing angle is displayed dynamically) air conditioner will swing circularly according to the angle as shown by the icon. Note: There is no this function for the units. If press this key, the main unit will click, but it also runs under original status. 7 HEALTH SAVE button HEALTH FUNCTION: After pressing HEALTH button, remote controller will switch circularly as below: "HEALTH"→"AIR"→"AIR HEALTH"→"no display" ● When selecting "HEALTH" by remote controller, HEALTH function will be started up. ● When selecting "AIR" by remote controller, AIR function will be started up. ● When selecting "AIT HEALTH", AIR and HEALTH function will be started up. ● When there’s no display on remote controller, AIR and HEALTH function will be turned off. ● AIR function is applicable for some models. 4 Introduction for buttons on remote controller SAVE function: Under cool mode, press SAVE button and the unit will operate under SAVE mode. Dual-8nixie tube on remote controller displays "SE". Air conditioner will operate at auto speed. Set temperature can’t be adjusted. Press SAVE button again to exit SAVE mode. Air conditioner turn back to original set speed and set temperature. ● This function is applicable to partial of models. 8 X-FAN button After pressing this button under cooling or dry mode, remote controller displays the character of "X-FAN" and X-FAN function is started up. Press this button again to cancel X-FAN function. The character of "X-FAN" will disappear. Note: ● After starting up X-FAN function, when turning off the unit, indoor fan will continue to operate for a while at low speed to dry the residual water inside the indoor unit. ● When the unit operates under X-FAN mode, press "X-FAN" button can turn off X-FAN function. Indoor fan stops operation immediately. 9 TEMP button Press this button can see indoor set temperature, indoor ambient temperature or outdoor ambient temperature on indoor unit’s display. Temperature is set circularly by remote controller as below: no display ● When selecting " " by remote controller or no display, temperature indicator on indoor unit displays set temperature. ● When selecting " " by remote controller, temperature indicator on indoor unit displays indoor ambient temperature. ● When selecting " " by remote controller, temperature indicator on indoor unit displays outdoor ambient temperature. Note: ● Outdoor ambient temperature display may can’t be selected for some models. When indoor unit receives " " signal, it displays indoor set temperature. ● Only for the model whose indoor unit has dual-8 display. 10 TIMER button ● At ON status, press this button once can set TIMER OFF. The character of HOUR TIMER ON. After each pressing of "+" or "-" button, time will increase or decrease half an 5 Introduction for buttons on remote controller hour. When holding "+" or "-" button, 2s later, the time will change quickly until to Cancel TIMER OFF: Press "TIMER" button again under TIMER OFF status. ● At OFF status, press this button once can set TIMER ON. Please refer to TIMER off for detailed operation. Cancel TIMER ON: Press "TIMER" button again under TIMER ON status. Note: ● Time setting range: 0.5-24 hours. ● Time interval between two operations can’t exceed 5s. Otherwise, remote controller will exit the setting status automatically. 11 TURBO button 12 SLEEP button 13 LIGHT button When pressing this button under cooling or heating mode, air conditioner will enter into quick cooling or quick heating mode. The character of "TURBO" is displayed on remote controller. Press this button again to exit turbo function and the character of "TURBO" will be disappeared on remote controller. Press this button under cooling, heating mode can start up sleep function. " " icon will be displayed on remote controller. Press this button again to cancel sleep function. " "icon on remote controller will be displayed. Press this button can turn off the light for indoor unit’s display. " " icon on remote controller will disappear. Press this button again to turn on the light for indoor unit’s display. " " icon on remote controller will be displayed. Function introduction for combination buttons Child lock function Press "+" and "-" buttons simultaneously can turn on or turn off child lock function. When child lock function is started up, " " icon will be displayed on remote controller won’t send signal. Switchover function for temperature display After turning off the unit by remote controller, press "-" button and "MODE" button simultaneously to switch between ℃ and °F . KEY FEATURES & FUNCTIONS DEFROST FUNCTION This increases room comfort and saves energy by sensing the need for defrosting and eliminating unnecessary defrost cycles. SLEEP MODE You design a cycle to automatically adjust room temperatures during your sleep time, to maximize comfort and reduce utility bills. TURBO MODE This capacity boost function is the fastest way to reach a desired temperature setpoint, either in heating or cooling. Once setpoint is achieved, you can deactivate Turbo Mode for normal operation. X-FAN MODE Especially useful in humid areas, this function allows the indoor fan to run for a predetermined amount of time after the unit is turned off, to remove additional moisture from the coil. PRIVACY LOCK MODE This prevents unauthorized access or tampering. To lock the remote controller, push the “+” and “-” buttons simultaneously for 2 seconds. Repeat to unlock. OPTIONAL PHOTOCATALYTIC FILTER Advanced technology to improve indoor air quality and prevent the spread of bacteria and viruses. FAQs Why does the fan continue to run even when the unit is not cooling or heating? To maintain consistent temperatures and minimize energy-loss from constant starts and stops, the fan keeps air flowing past the thermostat. What temperature is displayed on the remote controller? The remote always displays your desired indoor temperature. (You may view current indoor and outdoor temperatures on the indoor unit’s Front Panel Display.) What happens if the remote is lost or damaged? Use the Manual Override button to manually operate the unit. Lift up the front panel section on the indoor unit and locate the button right-hand side. Press the button to turn ON the unit. (Not all functions will be available.) Press again to cancel Manual Override Mode and transfer control back to the remote controller. . Not all features available on all models. Your actual air conditioning and heating system and related devices may differ from the images shown in this manual For complete instructions on these and other functions, as well as important safety information, see the Owners Manual. For more information, visit www.cooperandhunter.us Specifications are subject to change without notice. Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice or without incurring obligations. © 2015 .All rights reserved. 66162927
advertising